I plan to better decouple the cdclk computation from actual
modesets. To that end make the cdclk code self sufficient in
being able to determine if a full cdclk calculation/update is
needed or not due to some not strictly cdclk related reason.
Currently we have three such things that depend active_pipes:
- cdclk_state->actual
- glk audio w/a
- dg2 power well stuff
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250923171943.7319-8-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Extract the code to determine the DG2 pipe power well count
into a small helper. I'll have other uses for this later.
TODO: need to move this power well stuff out from the cdclk code...
v2: Don't lose the early return from intel_cdclk_pcode_pre_notify()
(kernel test robot)
v3: Compare old vs. new, not old vs. old (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250926083950.24486-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
intel_bw_modeset_checks() is now only called from
intel_bw_atomic_check() which alrady does the display
version check. Drop the redundant check from
intel_bw_modeset_checks().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250923171943.7319-5-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Currently we may end up doing a bunch of redundant bw_state
recomputation whenever any modeset happens. Skip a bunch of
that by only considering whether any pipe actually changes
its active state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250923171943.7319-4-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Currently we use the implicit modifier fb creation path for fbdev,
but as we never call set_tiling on the bo it will always end up as
linear anyway. The rest of the code (eg. stride alignment) also
assumes that we'll use linear. Just select the linear modifier
explicitly.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-4-ville.syrjala@linux.intel.com
intel_frontbuffer_get() is what locks out subsequent set_tiling
changes to the bo. Thus the fence vs. modifier check must be done
after intel_frontbuffer_get(), or else a concurrent set_tiling ioctl
might sneak in and change the fence after the check has been done.
Close the race again. See commit dd689287b9 ("drm/i915: Prevent
concurrent tiling/framebuffer modifications") for the previous
instance.
v2: Reorder intel_user_framebuffer_destroy() to match the unwind (Jani)
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Fixes: 10690b8a49 ("drm/i915/display: Add intel_fb_bo_framebuffer_fini")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-3-ville.syrjala@linux.intel.com
Currently xe's intel_frontbuffer implementation forgets to
hold a reference on the bo. This makes the entire thing
extremely fragile as the cleanup order now depends on bo
references held by other things
(namely intel_fb_bo_framebuffer_fini()).
Move the bo refcounting to intel_frontbuffer_{get,release}()
so that both i915 and xe do this the same way.
I first tried to fix this by having xe do the refcounting
from its intel_bo_set_frontbuffer() implementation
(which is what i915 does currently), but turns out xe's
drm_gem_object_free() can sleep and thus drm_gem_object_put()
isn't safe to call while we hold fb_tracking.lock.
Fixes: 10690b8a49 ("drm/i915/display: Add intel_fb_bo_framebuffer_fini")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
drm_crtc_accurate_vblank_count takes a spinlock, which we should avoid
in tracepoints and debug functions.
This also prevents taking the spinlock 2x during the critical
section of pipe updates for DSI updates.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250829131701.15607-2-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Luca Abeni reported this:
| BUG: scheduling while atomic: kworker/u8:2/15203/0x00000003
| CPU: 1 PID: 15203 Comm: kworker/u8:2 Not tainted 4.19.1-rt3 #10
| Call Trace:
| rt_spin_lock+0x3f/0x50
| gen6_read32+0x45/0x1d0 [i915]
| g4x_get_vblank_counter+0x36/0x40 [i915]
| trace_event_raw_event_i915_pipe_update_start+0x7d/0xf0 [i915]
The tracing events use trace_intel_pipe_update_start() among other events
use functions acquire spinlock_t locks which are transformed into
sleeping locks on PREEMPT_RT. A few trace points use
intel_get_crtc_scanline(), others use ->get_vblank_counter() wich also
might acquire a sleeping locks on PREEMPT_RT.
At the time the arguments are evaluated within trace point, preemption
is disabled and so the locks must not be acquired on PREEMPT_RT.
Based on this I don't see any other way than disable trace points on
PREMPT_RT.
[mlankhorst]
The original patch was insufficient, and since the tracing
infrastructure does not allow for partial disabling of tracepoints.
Completely disable tracing for the entire i915 driver in PREEMPT_RT,
a separate fix for display tracepoints on xe is added to make those
work.
Cc: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reported-by: Luca Abeni <lucabe72@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Co-developed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250828090944.101069-1-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Now as intel_dp->alpm_parameters doesn't really contain any parameters it
doesn't make sense to call it as alpm_parameters -> remove parameters
suffix.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://lore.kernel.org/r/20250929130003.28365-2-jouni.hogander@intel.com
Currently ALPM parameters are computed directly into
intel_dp->alpm_parameters. This is a problem when compute config ends up to
not using the computed state.
Fix this by adding ALPM parameters into intel_crtc_state and compute into
there. Copy needed parameters (io_wake_lines and fast_wake_lines used by
PSR activate/exit) from crtc_state->alpm_state into
intel_dp->alpm.alpm_parameters when they are configured into HW.
v3:
- enhance commit message
v2:
- store io/fast wake lines into intel_dp->dp instead of
intel_dp->alpm_parameters and do it in intel_psr_enable_locked
- rename crtc_state->alpm_parameters -> crtc_state->alpm_state
- clarify commit message
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://lore.kernel.org/r/20250929130003.28365-1-jouni.hogander@intel.com
intel_get_linetime_us() is a mess. Rewrite it in a straightforward
manner. Also the checks for the !active and pixel_rate==0 are
completely pointless here since we know that the plane is visible.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250919180838.10498-3-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
The line time used for the watermark calculations is supposed to
based on the plane's adjusted pixel rate, not the pipe's adjusted
pixel rate. The current code will give incorrect answers if plane
downscaling is used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250919180838.10498-2-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
According to Bspec, before enabling AUX power, we need to have the
"power well containing Aux logic powered up". Starting with Xe2_LPD,
such power well is the "PICA" power well, which is managed by the driver
on demand.
While we did add the mapping of AUX power domains to the PICA power
well, we ended up placing its power well descriptor after the
descriptor for AUX power. As a result, when enabling power wells for one
of the aux power domains, the driver will enable AUX power before PICA
power, going against the order specified in Bspec.
It appears that issue did not become apparent to us mainly because,
luckily, AUX power is brought up after we assert PICA power, even if
done in the wrong order; and in enough time for the first AUX
transaction to succeed.
Furthermore, I have also realized that, in some cases, like driver
initialization, PICA power is already up when we need to acquire AUX
power.
One case where we can observe the incorrect ordering is when the driver
is resuming from runtime PM suspend. Here is an excerpt of a dmesg with
some extra debug logs extracted from a LNL machine to illustrate the
issue:
[ +0.000156] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_TC1
[ +0.001312] xe 0000:00:02.0: [drm:xelpdp_aux_power_well_enable [xe]] DBG: AUX_CH_USBC1 power status: 0
[ +0.000127] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC
[ +0.001072] xe 0000:00:02.0: [drm:xe2lpd_pica_power_well_enable [xe]] DBG: AUX_CH_USBC1 power status: 1
[ +0.000102] xe 0000:00:02.0: [drm:xe2lpd_pica_power_well_enable [xe]] DBG: AUX_CH_USBC2 power status: 0
[ +0.000090] xe 0000:00:02.0: [drm:xe2lpd_pica_power_well_enable [xe]] DBG: AUX_CH_USBC3 power status: 0
[ +0.000092] xe 0000:00:02.0: [drm:xe2lpd_pica_power_well_enable [xe]] DBG: AUX_CH_USBC4 power status: 0
The first "DBG: ..." line shows that AUX power for TC1 is off after we
assert and wait. The remaining lines show that AUX power for TC1 was on
after we enabled PICA power and waited for AUX power.
It is important that we stay compliant with the spec, so let's fix this
by listing the power wells in an order that matches the requirements
from Bspec. (As a side note, it would be nice if we could define those
dependencies explicitly.)
After this change, we have:
[ +0.000146] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC
[ +0.001417] xe 0000:00:02.0: [drm:xe2lpd_pica_power_well_enable [xe]] DBG: AUX_CH_USBC1 power status: 0
[ +0.000116] xe 0000:00:02.0: [drm:xe2lpd_pica_power_well_enable [xe]] DBG: AUX_CH_USBC2 power status: 0
[ +0.000096] xe 0000:00:02.0: [drm:xe2lpd_pica_power_well_enable [xe]] DBG: AUX_CH_USBC3 power status: 0
[ +0.000094] xe 0000:00:02.0: [drm:xe2lpd_pica_power_well_enable [xe]] DBG: AUX_CH_USBC4 power status: 0
[ +0.000095] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_TC1
[ +0.000915] xe 0000:00:02.0: [drm:xelpdp_aux_power_well_enable [xe]] DBG: AUX_CH_USBC1 power status: 1
Bspec: 68967, 68886, 72519
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20251001-pica-power-before-aux-v2-2-6308df4de5a8@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
In an upcoming change, we will fix an ordering issue between PICA and
AUX power wells for Xe2_LPD and later, making sure that the driver
acquires PICA power before AUX. As a preparation for that, let's
extract separate descriptors for AUX power wells.
Suggested-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20251001-pica-power-before-aux-v2-1-6308df4de5a8@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Handle the DSC pixel throughput quirk, limiting the compressed link-bpp
value for Synaptics Panamera branch devices, working around a
blank/unstable output issue observed on docking stations containing
these branch devices, when using a mode with a high pixel clock and a
high compressed link-bpp value.
For now use the same mode clock limit for RGB/YUV444 and YUV422/420
output modes. This may result in limiting the link-bpp value for a
YUV422/420 output mode already at a lower than required mode clock.
v2: Apply the quirk only when DSC is enabled.
v3 (Ville):
- Move adjustment of link-bpp within the already existing is_dsc
if branch.
- Add TODO comment to move the HW revision check as well to the
DRM core quirk table.
v4:
- Fix incorrect fxp_q4_from_int(INT_MAX) vs. INT_MAX return value
from dsc_throughput_quirk_max_bpp_x16().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reported-and-tested-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250930182450.563016-7-imre.deak@intel.com
Read out the branch devices' maximum overall DSC pixel throughput and
line width and verify the mode's corresponding pixel clock and hactive
period against these.
v2: Use drm helpers to query the throughput/line-width caps. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-and-tested-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250930182450.563016-6-imre.deak@intel.com
Pass the DPCD sink/branch device descriptor along with the
is_branch/sink flag to intel_dp_get_dsc_sink_cap(). These will be used
by a follow up change to read out the branch device's DSC overall
throughput/line width capabilities and to detect a throughput/link-bpp
quirk.
Reported-and-tested-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250930182450.563016-5-imre.deak@intel.com
Use the DSC sink device's actual per-slice peak throughput to calculate
the minimum number of required DSC slices, falling back to the
hard-coded throughput values (as suggested by the DP Standard) if the
device's reported throughput value is 0.
For now use the minimum of the two throughput values, which is ok,
potentially resulting in a higher than required minimum slice count.
This doesn't change the current way of using the same minimum throughput
value regardless of the RGB/YUV output format used.
While at it add a TODO comment for MST tiled displays to calculate the
slice count for these based on the total pixel rate of all the tiles.
v2: Use drm helpers to query the throughput caps. (Ville)
v3: Add TODO comment to account for MST tiled displays. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-and-tested-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250930182450.563016-4-imre.deak@intel.com
Add helpers to query the DP DSC sink device's per-slice throughput as
well as a DSC branch device's overall throughput and line-width
capabilities.
v2 (Ville):
- Rename pixel_clock to peak_pixel_rate, document what the value means
in case of MST tiled displays.
- Fix name of drm_dp_dsc_branch_max_slice_throughput() to
drm_dp_dsc_sink_max_slice_throughput().
v3:
- Fix the DSC branch device minimum valid line width value from 2560
to 5120 pixels.
- Fix drm_dp_dsc_sink_max_slice_throughput()'s pixel_clock parameter
name to peak_pixel_rate in header file.
- Add handling for throughput mode 0 granular delta, defined by DP
Standard v2.1a.
v4:
- Remove the default switch case in
drm_dp_dsc_sink_max_slice_throughput(), which is unreachable in the
current code. (Ville)
Cc: dri-devel@lists.freedesktop.org
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-and-tested-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250930182450.563016-3-imre.deak@intel.com
Some Synaptics MST branch devices have a problem decompressing a stream
with a compressed link-bpp higher than 12, if the pixel clock is higher
than ~50 % of the maximum throughput capability reported by the branch
device. The screen remains blank, or for some - mostly black content -
gets enabled, but may stil have jitter artifacts.
At least the following docking stations are affected, based on testing
both with any Intel devices or the UCD-500 reference device as a source:
- DELL WD19DCS, DELL WD19TB3, DELL WD22TB4
- ThinkPad 40AN
- HP G2
At least the following docking stations are free from this problem,
based on tests with a source/sink/mode etc. configuration matching the
test cases used above:
- DELL Dual Charge HD22Q, DELL WD25TB5
- ThinkPad 40B0
- Anker 565
All the affected devices have an older version of the Synaptics MST
branch device (Panamera), whereas all the non-affected docking stations
have a newer branch device (at least Synaptics Panamera with a higher HW
revision number and Synaptics Cayenne models). Add the required quirk
entries accordingly. The quirk will be handled by the i915/xe drivers in
a follow-up change.
The latest firmware version of the Synaptics branch device for all the
affected devices tested above is 5.7 (as reported at DPCD address
0x50a/0x50b). For the DELL devices this corresponds to the latest
01.00.14.01.A03 firmware package version of the docking station.
v2:
- Document the DP_DPCD_QUIRK_DSC_THROUGHPUT_BPP_LIMIT enum.
- Describe the quirk in more detail in the dpcd_quirk_list.
v3:
- s/Panarema/Panamera in the commit log.
Cc: dri-devel@lists.freedesktop.org
Reported-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reported-and-tested-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250930182450.563016-2-imre.deak@intel.com
Return the actual error code from vfio_set_irqs_validate_and_prepare()
instead of always collapsing to -EINVAL. While the helper
currently returns -EINVAL in most cases, passing through the real
error code is more future-proof.
While at it, drop the stray 'intel:' prefix from the error
message.
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw.linux@gmail.com>
Link: https://lore.kernel.org/r/20251001142336.82089-1-andi.shyti@linux.intel.com
The error irq handling needs to mask page table errors on gen 2/3 with
FBC. See commit e7e12f6ec8 ("drm/i915: Mask page table errors on
gen2/3 with FBC") for details.
We want to avoid using display feature checks in i915 core code. Since
FBC can't be fused off on gen 2/3, just list the platforms that support
FBC. Add a macro purely for making the code self-documenting.
With this, we can drop the intel_display_core.h include, and make struct
intel_display opaque inside i915_irq.c.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250929133418.2033006-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The display driver needs to get from the struct drm_device pointer to
the struct intel_display pointer. Currently, this depends on knowledge
of the struct drm_i915_private and struct xe_device definitions, but
we'd like to hide those definitions from display.
Require the struct drm_device and struct intel_display * members within
struct drm_i915_private and struct xe_device to be placed next to each
other, to be able to figure out the display pointer without knowledge of
the structures.
Use a generic dummy device structure to define the relative offsets of
the drm and display members, and add static assertions to ensure this
holds for both i915 and xe. Use the dummy structure to do the pointer
chase from struct drm_device * to struct intel_display *.
This requires moving the display member in struct xe_device after the
drm member.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Suggested-by: Simona Vetter <simona.vetter@ffwll.ch>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250926111032.1188876-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add i915_gem_stolen_node_alloc() and i915_gem_stolen_node_free(),
returning struct intel_stolen_node pointer. Make struct
intel_stolen_node an opaque pointer, with different implementations in
i915 and xe.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/3fe71bbb4c75ee86b4d129fafa3d4cd6526363f4.1758732183.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
i915_gem_stolen.h simply defines intel_stolen_node as drm_mm_node. Make
struct intel_stolen_node an actual struct of its own right, and embed
struct drm_mm_node inside. This allow better unification between i915
and xe.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/36762f611566d81427e702369f4e8207ead5f26c.1758732183.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Using intel_psr_exit in frontbuffer flush on older platforms seems to be
causing problems.
Sending single full frame update using intel_psr_force_update is anyways
more optimal compared to psr deactivate/activate -> move back to this
approach on PSR1, PSR HW tracking and Panel Replay full frame update and
use deactivate/activate only on LunarLake and only when selective fetch is
enabled.
Tested-by: Lemen <lemen@lemen.xyz>
Tested-by: Koos Vriezen <koos.vriezen@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14946
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://lore.kernel.org/r/20250922102725.2752742-1-jouni.hogander@intel.com
This tag contains habanalabs driver changes for v6.18.
It continues the previous upstream work from tags/drm-habanalabs-next-2024-06-23,
Including improvements in debug and visibility, alongside general code cleanups,
and new features such as vmalloc-backed coherent mmap, HLDIO infrastructure, etc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: "Elbaz, Koby" <koby.elbaz@intel.com>
Link: https://lore.kernel.org/r/da02d370-9967-49d2-9eef-7aeaa40c987c@intel.com
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Signed-off-by: Madhur Kumar <madhurkumar004@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20250923195051.1277855-1-madhurkumar004@gmail.com
Add error handling for the following VFIO_DEVICE_SET_IRQS cases with
respect to the hdr struct:
- More than one VFIO_IRQ_DATA_TYPE_MASK flag is set in hdr.flags
- More than one VFIO_IRQ_ACTION_TYPE_MASK flag is set in hdr.flags
- hdr.count is not specified
Note that since hdr.count != 0, data_size != 0 is guaranteed unless
vfio_set_irqs_validate_and_prepare fails and returns an error. So, we
no longer need to check data_size before running memdup_user because
checking the return value of the function is sufficient.
v2: Use correct name for mask
v3: Use is_power_of_2 over hweight32 as it's more efficient (Andi)
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw.linux@gmail.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20250923212332.112137-2-jonathan.cavitt@intel.com
We do not need a case switch to check cap_type_id in intel_vgpu_ioctl
for various reasons (it's impossible to hit the default case in the
current code, there's only one valid case to check, the error handling
code overlaps in both cases, etc.). Simplify the case switch into a
single if statement. This has the additional effect of simplifying the
error handling code.
Note that it is still currently impossible for
'if (cap_type_id == VFIO_REGION_INFO_CAP_SPARSE_MMAP)'
to fail, but we should still guard against the possibility of this
changing in the future.
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw.linux@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20250918214515.66926-2-jonathan.cavitt@intel.com
Drop the now single-use dsb_vblank_delay() helper and inline its logic
directly into intel_dsb_wait_for_delayed_vblank().
This will help to keep all VRR related wait stuff in one place.
v2: Use intel_scanlines_to_usecs() in intel_dsb_wait_usec(). (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250925022352.3129859-1-ankit.k.nautiyal@intel.com
