During firmware recovery, the monitor interface is not
getting created in the driver and firmware since
the respective flags are not updated properly.
So after firmware recovery is successful, when monitor
interface is brought down manually, firmware assertion
is observed, since we are trying to bring down the
interface which is not yet created in the firmware.
Fix this by updating the monitor flags properly per
phy#, during firmware recovery.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221014155054.11471-1-quic_nmaran@quicinc.com
On WCN3990, we are seeing a rare scenario where copy engine hardware is
sending a copy complete interrupt to the host driver while still
processing the buffer that the driver has sent, this is leading into an
SMMU fault triggering kernel panic. This is happening on copy engine
channel 3 (CE3) where the driver normally enqueues WMI commands to the
firmware. Upon receiving a copy complete interrupt, host driver will
immediately unmap and frees the buffer presuming that hardware has
processed the buffer. In the issue case, upon receiving copy complete
interrupt, host driver will unmap and free the buffer but since hardware
is still accessing the buffer (which in this case got unmapped in
parallel), SMMU hardware will trigger an SMMU fault resulting in a
kernel panic.
In order to avoid this, as a work around, add a delay before unmapping
the copy engine source DMA buffer. This is conditionally done for
WCN3990 and only for the CE3 channel where issue is seen.
Below is the crash signature:
wifi smmu error: kernel: [ 10.120965] arm-smmu 15000000.iommu: Unhandled
context fault: fsr=0x402, iova=0x7fdfd8ac0,
fsynr=0x500003,cbfrsynra=0xc1, cb=6 arm-smmu 15000000.iommu: Unhandled
context fault:fsr=0x402, iova=0x7fe06fdc0, fsynr=0x710003,
cbfrsynra=0xc1, cb=6 qcom-q6v5-mss 4080000.remoteproc: fatal error
received: err_qdi.c:1040:EF:wlan_process:0x1:WLAN RT:0x2091:
cmnos_thread.c:3998:Asserted in copy_engine.c:AXI_ERROR_DETECTED:2149
remoteproc remoteproc0: crash detected in
4080000.remoteproc: type fatal error <3> remoteproc remoteproc0:
handling crash #1 in 4080000.remoteproc
pc : __arm_lpae_unmap+0x500/0x514
lr : __arm_lpae_unmap+0x4bc/0x514
sp : ffffffc011ffb530
x29: ffffffc011ffb590 x28: 0000000000000000
x27: 0000000000000000 x26: 0000000000000004
x25: 0000000000000003 x24: ffffffc011ffb890
x23: ffffffa762ef9be0 x22: ffffffa77244ef00
x21: 0000000000000009 x20: 00000007fff7c000
x19: 0000000000000003 x18: 0000000000000000
x17: 0000000000000004 x16: ffffffd7a357d9f0
x15: 0000000000000000 x14: 00fd5d4fa7ffffff
x13: 000000000000000e x12: 0000000000000000
x11: 00000000ffffffff x10: 00000000fffffe00
x9 : 000000000000017c x8 : 000000000000000c
x7 : 0000000000000000 x6 : ffffffa762ef9000
x5 : 0000000000000003 x4 : 0000000000000004
x3 : 0000000000001000 x2 : 00000007fff7c000
x1 : ffffffc011ffb890 x0 : 0000000000000000 Call trace:
__arm_lpae_unmap+0x500/0x514
__arm_lpae_unmap+0x4bc/0x514
__arm_lpae_unmap+0x4bc/0x514
arm_lpae_unmap_pages+0x78/0xa4
arm_smmu_unmap_pages+0x78/0x104
__iommu_unmap+0xc8/0x1e4
iommu_unmap_fast+0x38/0x48
__iommu_dma_unmap+0x84/0x104
iommu_dma_free+0x34/0x50
dma_free_attrs+0xa4/0xd0
ath10k_htt_rx_free+0xc4/0xf4 [ath10k_core] ath10k_core_stop+0x64/0x7c
[ath10k_core]
ath10k_halt+0x11c/0x180 [ath10k_core]
ath10k_stop+0x54/0x94 [ath10k_core]
drv_stop+0x48/0x1c8 [mac80211]
ieee80211_do_open+0x638/0x77c [mac80211] ieee80211_open+0x48/0x5c
[mac80211]
__dev_open+0xb4/0x174
__dev_change_flags+0xc4/0x1dc
dev_change_flags+0x3c/0x7c
devinet_ioctl+0x2b4/0x580
inet_ioctl+0xb0/0x1b4
sock_do_ioctl+0x4c/0x16c
compat_ifreq_ioctl+0x1cc/0x35c
compat_sock_ioctl+0x110/0x2ac
__arm64_compat_sys_ioctl+0xf4/0x3e0
el0_svc_common+0xb4/0x17c
el0_svc_compat_handler+0x2c/0x58
el0_svc_compat+0x8/0x2c
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221012142733.32420-1-quic_youghand@quicinc.com
Return value of a function ath10k_get_arvif() is dereferenced without
checking for null in ath10k_wmi_event_tdls_peer(), but it is usually checked
for this function.
Make ath10k_wmi_event_tdls_peer() do check retval of ath10k_get_arvif().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Peter Kosyh <pkosyh@yandex.ru>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221003091217.322598-1-pkosyh@yandex.ru
Current code does not wait for vdev delete completion on vdev create
failures and tries to send another vdev create followed by vdev set
param to firmware with same vdev id. This causes firmware crash.
Fix this crash by waiting for vdev delete completion on vdev
create failures.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.6.0.1-00905-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221011095346.3901-1-quic_ssreeela@quicinc.com
We are seeing system stuck on some specific platforms due to
WLAN chip fails to wakeup from D3cold state.
With this flag, firmware will send PME message during wakeup
and this issue is gone.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221010033237.415478-1-quic_bqiang@quicinc.com
Add support to configure channel dwell time during scan.
Dwell time help to stay on the channel for a specified duration
during scan and aid userspace in finding WiFi networks. Very
useful in passive scans where longer dwell times are needed
to find the WiFi networks.
Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.
Advertise corresponding feature flag NL80211_EXT_FEATURE_SET_SCAN_DWELL
to enable the feature.
Change is applicable for all ath11k hardware.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221007051130.6067-1-quic_mpubbise@quicinc.com
In the VIF (other than monitor type) creation request, we should not
throw the error code when the monitor VIF creation fails, since the
actual VIF creation succeeds. If we throw the error code from driver
then the actual VIF creation get fail. So suppress the monitor VIF
creation error by throwing warning message instead of error code.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00760-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221006005842.8599-1-quic_periyasa@quicinc.com
Currently, ath11k sends peer assoc command for each peer to
firmware when bandwidth changes. Peer assoc command is a
bulky command and if many clients are connected, this could
lead to firmware buffer getting overflowed leading to a firmware
assert.
However, during bandwidth change, only phymode and bandwidth
also can be updated by WMI set peer param command. This makes
the overall command light when compared to peer assoc and for
multi-client cases, firmware buffer overflow also does not
occur.
Remove sending peer assoc command during sta bandwidth change
and instead add sending WMI set peer param command for phymode
and bandwidth.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: f187fe8e3b ("ath11k: fix firmware crash during channel switch")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221005095430.19890-1-quic_adisi@quicinc.com
GCC-12 emits false positive -Warray-bounds warnings with
CONFIG_UBSAN_SHIFT (-fsanitize=shift). This is fixed in GCC 13[1],
and there is top-level Makefile logic to remove -Warray-bounds for
known-bad GCC versions staring with commit f0be87c42c ("gcc-12: disable
'-Warray-bounds' universally for now").
Remove the local work-around.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=105679
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221006192051.1742930-1-keescook@chromium.org
The bug arises when a USB device claims to be an ATH9K but doesn't
have the expected endpoints. (In this case there was an interrupt
endpoint where the driver expected a bulk endpoint.) The kernel
needs to be able to handle such devices without getting an internal error.
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 3 PID: 500 at drivers/usb/core/urb.c:493 usb_submit_urb+0xce2/0x1430 drivers/usb/core/urb.c:493
Modules linked in:
CPU: 3 PID: 500 Comm: kworker/3:2 Not tainted 5.10.135-syzkaller #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Workqueue: events request_firmware_work_func
RIP: 0010:usb_submit_urb+0xce2/0x1430 drivers/usb/core/urb.c:493
Call Trace:
ath9k_hif_usb_alloc_rx_urbs drivers/net/wireless/ath/ath9k/hif_usb.c:908 [inline]
ath9k_hif_usb_alloc_urbs+0x75e/0x1010 drivers/net/wireless/ath/ath9k/hif_usb.c:1019
ath9k_hif_usb_dev_init drivers/net/wireless/ath/ath9k/hif_usb.c:1109 [inline]
ath9k_hif_usb_firmware_cb+0x142/0x530 drivers/net/wireless/ath/ath9k/hif_usb.c:1242
request_firmware_work_func+0x12e/0x240 drivers/base/firmware_loader/main.c:1097
process_one_work+0x9af/0x1600 kernel/workqueue.c:2279
worker_thread+0x61d/0x12f0 kernel/workqueue.c:2425
kthread+0x3b4/0x4a0 kernel/kthread.c:313
ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:299
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221008211532.74583-1-pchelkin@ispras.ru
It is possible that skb is freed in ath9k_htc_rx_msg(), then
usb_submit_urb() fails and we try to free skb again. It causes
use-after-free bug. Moreover, if alloc_skb() fails, urb->context becomes
NULL but rx_buf is not freed and there can be a memory leak.
The patch removes unnecessary nskb and makes skb processing more clear: it
is supposed that ath9k_htc_rx_msg() either frees old skb or passes its
managing to another callback function.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 3deff76095 ("ath9k_htc: Increase URB count for REG_IN pipe")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221008114917.21404-1-pchelkin@ispras.ru
GCC-12 emits false positive -Warray-bounds warnings with
CONFIG_UBSAN_SHIFT (-fsanitize=shift). This is fixed in GCC 13[1],
and there is top-level Makefile logic to remove -Warray-bounds for
known-bad GCC versions staring with commit f0be87c42c ("gcc-12: disable
'-Warray-bounds' universally for now").
Remove the local work-around.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=105679
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221006192054.1742982-1-keescook@chromium.org
Syzkaller reports a long-known leak of urbs in
ath9k_hif_usb_dealloc_tx_urbs().
The cause of the leak is that usb_get_urb() is called but usb_free_urb()
(or usb_put_urb()) is not called inside usb_kill_urb() as urb->dev or
urb->ep fields have not been initialized and usb_kill_urb() returns
immediately.
The patch removes trying to kill urbs located in hif_dev->tx.tx_buf
because hif_dev->tx.tx_buf is not supposed to contain urbs which are in
pending state (the pending urbs are stored in hif_dev->tx.tx_pending).
The tx.tx_lock is acquired so there should not be any changes in the list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 03fb92a432 ("ath9k: hif_usb: fix race condition between usb_get_urb() and usb_kill_anchored_urbs()")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725151359.283704-1-pchelkin@ispras.ru
Don't populate the read-only arrays prof_prio and channelmap
on the stack but instead make them static const. Also makes the
object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221005155558.320556-1-colin.i.king@gmail.com
Running this test in a loop it is easy to reproduce an rtnl deadlock:
iw reg set FI
ifconfig wlan0 down
What happens is that thread A (workqueue) tries to update the regulatory:
try to acquire the rtnl_lock of ar->regd_update_work
rtnl_lock+0x17/0x20
ath11k_regd_update+0x15a/0x260 [ath11k]
ath11k_regd_update_work+0x15/0x20 [ath11k]
process_one_work+0x228/0x670
worker_thread+0x4d/0x440
kthread+0x16d/0x1b0
ret_from_fork+0x22/0x30
And thread B (ifconfig) tries to stop the interface:
try to cancel_work_sync(&ar->regd_update_work) in ath11k_mac_op_stop().
ifconfig 3109 [003] 2414.232506: probe:
ath11k_mac_op_stop: (ffffffffc14187a0)
drv_stop+0x30 ([mac80211])
ieee80211_do_stop+0x5d2 ([mac80211])
ieee80211_stop+0x3e ([mac80211])
__dev_close_many+0x9e ([kernel.kallsyms])
__dev_change_flags+0xbe ([kernel.kallsyms])
dev_change_flags+0x23 ([kernel.kallsyms])
devinet_ioctl+0x5e3 ([kernel.kallsyms])
inet_ioctl+0x197 ([kernel.kallsyms])
sock_do_ioctl+0x4d ([kernel.kallsyms])
sock_ioctl+0x264 ([kernel.kallsyms])
__x64_sys_ioctl+0x92 ([kernel.kallsyms])
do_syscall_64+0x3a ([kernel.kallsyms])
entry_SYSCALL_64_after_hwframe+0x63 ([kernel.kallsyms])
__GI___ioctl+0x7 (/lib/x86_64-linux-gnu/libc-2.23.so)
The sequence of deadlock is:
1. Thread B calls rtnl_lock().
2. Thread A starts to run and calls rtnl_lock() from within
ath11k_regd_update_work(), then enters wait state because the lock is owned by
thread B.
3. Thread B continues to run and tries to call
cancel_work_sync(&ar->regd_update_work), but thread A is in
ath11k_regd_update_work() waiting for rtnl_lock(). So cancel_work_sync()
forever waits for ath11k_regd_update_work() to finish and we have a deadlock.
Fix this by switching from using regulatory_set_wiphy_regd_sync() to
regulatory_set_wiphy_regd(). Now cfg80211 will schedule another workqueue which
handles the locking on it's own. So the ath11k workqueue can simply exit without
taking any locks, avoiding the deadlock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
[kvalo: improve commit log]
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221006151747.13757-1-kvalo@kernel.org
Commit 26f3a021b3 ("ath11k: allocate smaller chunks of memory for
firmware") and commit f6f92968e1 ("ath11k: qmi: try to allocate a
big block of DMA memory first") change ath11k to allocate the memory
chunks for target twice while wlan load. It fails for the 1st time
because of large memory and then changed to allocate many small chunks
for the 2nd time sometimes as below log.
1st time failed:
[10411.640620] ath11k_pci 0000:05:00.0: qmi firmware request memory request
[10411.640625] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 6881280
[10411.640630] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 3784704
[10411.640658] ath11k_pci 0000:05:00.0: qmi dma allocation failed (6881280 B type 1), will try later with small size
[10411.640671] ath11k_pci 0000:05:00.0: qmi delays mem_request 2
[10411.640677] ath11k_pci 0000:05:00.0: qmi respond memory request delayed 1
2nd time success:
[10411.642004] ath11k_pci 0000:05:00.0: qmi firmware request memory request
[10411.642008] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642012] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642014] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642016] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642018] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642020] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642022] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642024] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642027] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642029] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642031] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 458752
[10411.642033] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 131072
[10411.642035] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642037] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642039] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642041] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642043] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642045] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642047] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 491520
[10411.642049] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
And then commit 5962f370ce ("ath11k: Reuse the available memory after
firmware reload") skip the ath11k_qmi_free_resource() which frees the
memory chunks while recovery, after that, when run recovery test on
WCN6855, a warning happened every time as below and finally leads fail
for recovery.
[ 159.570318] BUG: Bad page state in process kworker/u16:5 pfn:33300
[ 159.570320] page:0000000096ffdbb9 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x33300
[ 159.570324] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
[ 159.570329] raw: 000fffffc0000000 0000000000000000 dead000000000122 0000000000000000
[ 159.570332] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 159.570334] page dumped because: nonzero _refcount
[ 159.570440] firewire_ohci syscopyarea sysfillrect psmouse sdhci_pci ahci sysimgblt firewire_core fb_sys_fops libahci crc_itu_t cqhci drm sdhci e1000e wmi video
[ 159.570460] CPU: 2 PID: 217 Comm: kworker/u16:5 Kdump: loaded Tainted: G B 5.19.0-rc1-wt-ath+ #3
[ 159.570465] Hardware name: LENOVO 418065C/418065C, BIOS 83ET63WW (1.33 ) 07/29/2011
[ 159.570467] Workqueue: qmi_msg_handler qmi_data_ready_work [qmi_helpers]
[ 159.570475] Call Trace:
[ 159.570476] <TASK>
[ 159.570478] dump_stack_lvl+0x49/0x5f
[ 159.570486] dump_stack+0x10/0x12
[ 159.570493] bad_page+0xab/0xf0
[ 159.570502] check_free_page_bad+0x66/0x70
[ 159.570511] __free_pages_ok+0x530/0x9a0
[ 159.570517] ? __dev_printk+0x58/0x6b
[ 159.570525] ? _dev_printk+0x56/0x72
[ 159.570534] ? qmi_decode+0x119/0x470 [qmi_helpers]
[ 159.570543] __free_pages+0x91/0xd0
[ 159.570548] dma_free_contiguous+0x50/0x60
[ 159.570556] dma_direct_free+0xe5/0x140
[ 159.570564] dma_free_attrs+0x35/0x50
[ 159.570570] ath11k_qmi_msg_mem_request_cb+0x2ae/0x3c0 [ath11k]
[ 159.570620] qmi_invoke_handler+0xac/0xe0 [qmi_helpers]
[ 159.570630] qmi_handle_message+0x6d/0x180 [qmi_helpers]
[ 159.570643] qmi_data_ready_work+0x2ca/0x440 [qmi_helpers]
[ 159.570656] process_one_work+0x227/0x440
[ 159.570667] worker_thread+0x31/0x3d0
[ 159.570676] ? process_one_work+0x440/0x440
[ 159.570685] kthread+0xfe/0x130
[ 159.570692] ? kthread_complete_and_exit+0x20/0x20
[ 159.570701] ret_from_fork+0x22/0x30
[ 159.570712] </TASK>
The reason is because when wlan start to recovery, the type, size and
count is not same for the 1st and 2nd QMI_WLFW_REQUEST_MEM_IND message,
Then it leads the parameter size is not correct for the dma_free_coherent().
For the chunk[1], the actual dma size is 524288 which allocate in the
2nd time of the initial wlan load phase, and the size which pass to
dma_free_coherent() is 3784704 which is got in the 1st time of recovery
phase, then warning above happened.
Change to use prev_size of struct target_mem_chunk for the paramter of
dma_free_coherent() since prev_size is the real size of last load/recovery.
Also change to check both type and size of struct target_mem_chunk to
reuse the memory to avoid mismatch buffer size for target. Then the
warning disappear and recovery success. When the 1st QMI_WLFW_REQUEST_MEM_IND
for recovery arrived, the trunk[0] is freed in ath11k_qmi_alloc_target_mem_chunk()
and then dma_alloc_coherent() failed caused by large size, and then
trunk[1] is freed in ath11k_qmi_free_target_mem_chunk(), the left 18
trunks will be reuse for the 2nd QMI_WLFW_REQUEST_MEM_IND message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 5962f370ce ("ath11k: Reuse the available memory after firmware reload")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220928073832.16251-1-quic_wgong@quicinc.com
Currently, ath11k_pcic_read() returns an error if wakeup()
fails, this makes firmware crash debug quite hard because we can
get nothing.
Change to go ahead on wakeup failure, in that case we still may
get something valid to check. There should be no mislead due
to incorrect content because we are aware of the failure with the
log printed.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220928015140.5431-1-quic_bqiang@quicinc.com
Currently, recovery flag is set immediately upon firmware
exit but tx queues are stopped once firmware arrives back
and is ready which is during ath11k_core_restart. Once
ieee80211 hw restart is completed, tx queues are resumed.
If during the time delta between firmware exit and firmware
ready, mac80211 send packets, currently ath11k will drop it
since recovery flag will be set. But warning prints will
come -
"ath11k c000000.wifi: failed to transmit frame -108"
If more tx packets are there, this could lead to flooding
of above print.
However, actually tx queues should be stopped immediately
when firmware leaves. This will prevent packets to get
dropped when firmware is recovering.
Add fix to stop tx queues immediately after firmware exit.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220923170235.18873-1-quic_adisi@quicinc.com
ath.git patches for v6.1. Major changes:
ath11k
* cold boot calibration support on WCN6750
* Target Wake Time (TWT) debugfs support for STA interface
* support to connect to a non-transmit MBSSID AP profile
* enable remain-on-channel support on WCN6750
* implement SRAM dump debugfs interface
* enable threaded NAPI on all hardware
* WoW support for WCN6750
* support to provide transmit power from firmware via nl80211
* support to get power save duration for each client
* spectral scan support for 160 MHz
wcn36xx
* add SNR from a received frame as a source of system entropy
When STA roams from one AP to another, after roam is complete, host
driver tries to get TIM information from firmware. This is no longer
supported in the firmware & hence, this call will always fail.
This failure results in the below message being displayed on the
console all the time when roam is done.
ieee80211 phy0: brcmf_update_bss_info: wl dtim_assoc failed (-52)
Changes ensure that the host driver will no longer try to get TIM
information from firmware.
Signed-off-by: Ramesh Rangavittal <ramesh.rangavittal@infineon.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@infineon.com>
Signed-off-by: Ian Lin <ian.lin@infineon.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922104140.11889-5-ian.lin@infineon.com
Increase dcmd maximum buffer size to match firmware
configuration for new chips.
Signed-off-by: Lo(Double)Hsiang Lo <double.lo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Ian Lin <ian.lin@infineon.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922104140.11889-4-ian.lin@infineon.com
Adds support of 89459 chip pcie device and save restore support.
Signed-off-by: Alexander Prutskov <alep@cypress.com>
Signed-off-by: Joseph chuang <jiac@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Ian Lin <ian.lin@infineon.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922104140.11889-3-ian.lin@infineon.com
4373 has support of 16 WOWL patterns thus increasing the default value
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Ian Lin <ian.lin@infineon.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922104140.11889-2-ian.lin@infineon.com
The bug is here: "} else if (item) {".
The list iterator value will *always* be set and non-NULL by
list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element is found in list.
Use a new value 'iter' as the list iterator, while use the old value
'item' as a dedicated pointer to point to the found element, which
1. can fix this bug, due to now 'item' is NULL only if it's not found.
2. do not need to change all the uses of 'item' after the loop.
3. can also limit the scope of the list iterator 'iter' *only inside*
the traversal loop by simply declaring 'iter' inside the loop in the
future, as usage of the iterator outside of the list_for_each_entry
is considered harmful. https://lkml.org/lkml/2022/2/17/1032
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413091723.17596-1-xiam0nd.tong@gmail.com
We are seeing system hangs during WoWLAN suspend, and get below
two stacks:
Stack1:
[ffffb02cc1557b20] __schedule at ffffffff8bb10860
[ffffb02cc1557ba8] schedule at ffffffff8bb10f24
[ffffb02cc1557bb8] schedule_timeout at ffffffff8bb16d88
[ffffb02cc1557c30] wait_for_completion at ffffffff8bb11778
[ffffb02cc1557c78] __flush_work at ffffffff8b0b30cd
[ffffb02cc1557cf0] __cancel_work_timer at ffffffff8b0b33ad
[ffffb02cc1557d60] ath11k_mac_drain_tx at ffffffffc0c1f0ca [ath11k]
[ffffb02cc1557d70] ath11k_wow_op_suspend at ffffffffc0c5201e [ath11k]
[ffffb02cc1557da8] __ieee80211_suspend at ffffffffc11e2bd3 [mac80211]
[ffffb02cc1557dd8] wiphy_suspend at ffffffffc0f901ac [cfg80211]
[ffffb02cc1557e08] dpm_run_callback at ffffffff8b75118a
[ffffb02cc1557e38] __device_suspend at ffffffff8b751630
[ffffb02cc1557e70] async_suspend at ffffffff8b7519ea
[ffffb02cc1557e88] async_run_entry_fn at ffffffff8b0bf4ce
[ffffb02cc1557ea8] process_one_work at ffffffff8b0b1a24
[ffffb02cc1557ee0] worker_thread at ffffffff8b0b1c4a
[ffffb02cc1557f18] kthread at ffffffff8b0b9cb8
[ffffb02cc1557f50] ret_from_fork at ffffffff8b001d32
Stack2:
[ffffb02cc00b7d18] __schedule at ffffffff8bb10860
[ffffb02cc00b7da0] schedule at ffffffff8bb10f24
[ffffb02cc00b7db0] schedule_preempt_disabled at ffffffff8bb112b4
[ffffb02cc00b7db8] __mutex_lock at ffffffff8bb127ea
[ffffb02cc00b7e38] ath11k_mgmt_over_wmi_tx_work at ffffffffc0c1aa44 [ath11k]
[ffffb02cc00b7ea8] process_one_work at ffffffff8b0b1a24
[ffffb02cc00b7ee0] worker_thread at ffffffff8b0b1c4a
[ffffb02cc00b7f18] kthread at ffffffff8b0b9cb8
[ffffb02cc00b7f50] ret_from_fork at ffffffff8b001d32
From the first stack, ath11k_mac_drain_tx calls
cancel_work_sync(&ar->wmi_mgmt_tx_work) and waits all packets to be sent
out or dropped. However, we find from Stack2 that this work item is blocked
because ar->conf_mutex is already held by ath11k_wow_op_suspend.
Fix this issue by moving ath11k_mac_wait_tx_complete to the start of
ath11k_wow_op_suspend where ar->conf_mutex has not been acquired. And
this change also makes the logic in ath11k_wow_op_suspend match the
logic in ath11k_mac_op_start and ath11k_mac_op_stop.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220919021435.2459-1-quic_bqiang@quicinc.com
ath11k_mac_drain_tx is already called in ath11k_mac_wait_tx_complete, no need to call it again. So remove it.
This is found in code review.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220919020259.1746-1-quic_bqiang@quicinc.com
There are two types of 160 MHz spectral scan support mentioned below
1. Fragmented approach
2. Single event approach
In this fragmented approach, single 160 MHz will be split as two
80 MHz buffer. First fft sample buffer will contain spectral scan
result of primary 80 MHz and the second fft sample buffer will contain
secondary 80 MHz and here cfreq1 and cfreq2 will be mentioned.
In case of 160 MHz on 36th channel will contain cfreq1 as 5210 and
cfreq2 as 5290. Chipsets which support this approach are IPQ8074/IPQ6018.
Replacing freq1 with freq2 in every secondary sepctral scan event to
distinguish between two different 80 MHz spectral event data.
In the 2nd approach each fft sample buffer will contain spectral scan
result for whole 160 MHz by mentioning cfreq1 as 5250 which is center
frequency of whole 160 MHz. Chipset which support this approach is QCN9074.
Host will receive spectral event from target for every 5 fft samples.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01120-QCAHKSWPL-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01120-QCAHKSWP
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725055001.15194-1-quic_tamizhr@quicinc.com
Add support to get the following power save information through debugfs interface,
* Current ps state of the peer
* Time duration since the peer is in power save
* Total duration of the peer spent in power save
Above information is helpful in debugging the issues with power save clients.
This patch also add trace log support for PS timekeeper to track the PS state
change of the peers alongs with the peer MAC address and timestamp.
Use the below commands to get the above power save information,
To know the time_since_station_in_power_save:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/current_ps_duration
To know power_save_duration:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/total_ps_duration
To reset the power_save_duration of all stations connected to AP:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath11k/reset_ps_duration
To enable/disable the ps_timekeeper:
echo Y > /sys/kernel/debug/ieee80211/phyX/ath11k/ps_timekeeper_enable
Y = 1 to enable and Y = 0 to disable.
To record PS timekeeer logs after enabling ps_timekeeper:
trace-cmd record -e ath11k_ps_timekeeper
Tested-on: Tested-on: IPQ8074 WLAN.HK.2.5.0.1-00991-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725054601.14719-1-quic_tamizhr@quicinc.com
This patch try to fix the following error.
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561227] ath11k c000000.wifi: peer already added vdev id 0 req, vdev id 1 present
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561282] ath11k c000000.wifi: Failed to add peer: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.568053] ath11k c000000.wifi: Failed to add station: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: Could not add STA to kernel driver
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: did not acknowledge authentication response
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED 28:c2:1f:xx:xx:xx
Wed Jun 1 22:19:31 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: disassociated due to inactivity
Wed Jun 1 22:19:32 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
To repro this:
- Have 2 Wifi with the same bssid and pass on different band (2.4 and
5GHz)
- Enable 802.11r Fast Transaction with same mobility domain
- FT Protocol: FT over the Air
From a openwrt system issue the command (with the correct mac)
ubus call hostapd.wlan1 wnm_disassoc_imminent '{"addr":"28:C2:1F:xx:xx:xx"}'
Notice the log printing the errors.
The cause of this error has been investigated and we found that this is
related to the WiFi Fast Transaction feature. We observed that this is
triggered when the router tells the device to change band. In this case
the device first auth to the other band and then the disconnect path
from the prev band is triggered.
This is problematic with the current rhash implementation since the
addrs is used as key and the logic of "adding first, delete later"
conflicts with the rhash logic.
In fact peer addition will fail since the peer is already added and with
that fixed a peer deletion will cause unitended effect by removing the
peer just added.
Current solution to this is to add additional logic to the peer delete,
make sure we are deleting the correct peer taken from the rhash
table (and fallback to the peer list) and for the peer add logic delete
the peer entry for the rhash list before adding the new one (counting as
an error only when a peer with the same vlan_id is asked to be added).
With this change, a sta can correctly transition from 2.4GHz and 5GHZ
with no drop and no error are printed.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: 7b0c70d92a ("ath11k: Add peer rhash table support")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603164559.27769-1-ansuelsmth@gmail.com
To enable/disable amsdu in set_tid_config, and currently only support to
configure all tids (==0xff) for AMSDU, not individual tid.
The command example is:
iw wlan0 set tidconf tids 0xff amsdu off
iw wlan0 set tidconf peer xx:xx:xx:xx:xx:xx tids 0xff amsdu on
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922012737.15091-1-pkshih@realtek.com
Align with the spec of 802.11ax, follow the conditions for not responding
with an HE TB PPDU. When there are OBSS that cannot interpret 26-tone RU
transmissions, we should disable such transmissions.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922012719.15037-1-pkshih@realtek.com
Support P2P client to process Notice of Absence (NoA) mechanism when it
connects with P2P GO applying an NoA schedule. We define some action
types including init, update, remove and terminate in h2c function to
enable/disable NoA schedule.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-6-pkshih@realtek.com
To handle a connected client using WMM-PS, the P2P GO also need to enable
this power save mechanism.
We add WIPHY_FLAG_AP_UAPSD flag to support it and define maximum number
of buffered frames the WMM GO may deliver to the WMM client.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-5-pkshih@realtek.com
Consider vif->p2p to set wifi_role to let firmware know current vif is
running as GC or GO. And, allow GC to enter PS mode, but disallow to enter
deep PS for now.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-4-pkshih@realtek.com
Check IEEE80211_TX_CTL_NO_CCK_RATE flag to avoid sending frames with
CCK rates in 2GHz band.
In TX flow, add IEEE80211_TX_CTL_NO_CCK_RATE flag to check and get its
lowest rate without CCK rates if the TX type is mgmt frames or data frames.
Besides, the decision of phy rate and retry rate in P2P mode are also
be handled.
In P2P GO mode, it should send beacon of no CCK rates in its frame rate.
Therefore, We add a condition to decide which rate is added to beacon
content.
Moreover, we avoid setting a mask of rates to be used for rate control
selection before and after connection in P2P mode.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-3-pkshih@realtek.com
To support P2P in driver, we set P2P interface mode to the wiphy
allocated for 802.11 PHY and add a change interface function to
switch the interface type to P2P.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-2-pkshih@realtek.com
Instead of using the default value 33 (pci), set US_CYC_CNT init based
on Programming guide:
If available, set chipset bus clock with fallback to cpu clock/3.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/3e275d259f476f597dab91a9c395015ef3fe3284.1663445157.git.daniel@makrotopia.org
Add RXIQ calibration found in mtk driver. With old openwrt builds this
gets us ~8Mbps more of RX bandwidth (test with iPA/eLNA layout).
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/033a39a697d51f6df258acea4c33608e0944fe4c.1663445157.git.daniel@makrotopia.org
