Add support for the MCIMXHDMICARD expansion card attached to the iMX53
QSB / QSRB platforms. This enables HDMI output on those devices.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove /omit-if-no-ref/ from node usdhc1-pwrseq, because if the compile
flag -@ (include symbols) is used the node will always be there. In this
case, GPIO H is not released and therefore cannot be used. Therefore,
remove this node manually from the corresponding devicetree file and
don't rely on /omit-if-no-ref/.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the new Apalis Evaluation Board v1.2. Because
only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
has been created which has common hardware configurations for v1.0, v1.1
and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
files include imx6q-apalis-eval.dtsi.
Versions 1.0 and 1.1 are compatible with each other and should
use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
should be used.
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add aliases for all ethernet nodes including the switch. It makes it
easier to find this nodes by the boot loader.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
HummingBoard has two RTCs, first integrated within SoC that can be used to
wake up from sleep - and a second on the carrier board including back-up
battery which is intended for keeping time during power-off.
Add aliases for both, ensuring that the battery-backed clock is primary
rtc and used by default during boot for restoring system time.
Fixes keeping time across power-cycle observed on Debian,
which sets RTC_HCTOSYS_DEVICE="rtc0".
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Sielaff i.MX6 Solo board is used as controller and user interface
in vending machines. It is based on the i.MX6 Solo SoC and features
the following peripherals and interfaces:
* 512 MB DDR3 RAM
* 512 MB NAND Flash
* 1 MB NOR Flash
* SD card
* Debug LED
* Debug UART
* Key Inputs
* RTC
* RS232
* 100 MBit Ethernet
* USB Hub
* USB OTG
* HDMI
* 7" LVDS IPS panel
* PWM Backlight
* Optional Extension Board with USB Ethernet NIC
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the dtbs_check warning:
tempmon: '#thermal-sensor-cells' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The display is in landscape orientation, but the touchscreen is in portrait
orientation. Specify that properly in the devicetree.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Due to CPU lifetime consideration of the SoC manufacturer [1] and
the preferred area of operation in the industrial related
environment, set the maximum frequency for each DHCOM i.MX6ULL to
792MHz, as with the industrial type. This is done by removing the
operating point at 900MHz and set the clock-frequency to 792000000.
[1] https://www.nxp.com/docs/en/application-note/AN5337.pdf
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
regulator-*-microvolt is not the range the regulator supports, but the
range which the regulator is allowed to configure. Limit v33 rail to
3.3V only.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the warnings:
pca953x 1-0020: supply vcc not found, using dummy regulator
lm75 0-0049: supply vs not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the warnings:
at24 0-0050: supply vcc not found, using dummy regulator
at24 0-0056: supply vcc not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These properties are only used on USB OTG/DR devices, remove them from
a host only device.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
temperature-sensor is the recommended node name and its main purpose.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is manufacturer data and shall not be modified.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDMA is enabled by default, so remove the status property.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USDHC3 is directly connected to an eMMC, so disable other interface modes.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USDHC1 is directly connected to an SD card, so disable other interface modes.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
0x56 is the EEPROM component of SE97BTP.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the pin muxing and GPIO settings for SCL/SDA for i2c2 & i2c3.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the pin muxing and GPIO settings for SCL/SDA for i2c1.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ensure the RTC devices are numbered correctly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows using S10 for power down / shutdown.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C expander is capable of generating an IRQ during powersave, so the
attached buttons can be used for waking up the system.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PCIE_DIS & PCIE_RST (correctly named W_DISABLE# & PERST#) affect USB
devices as well. So hog them to make USB devices attached to Mini PCIe
connector available, despite PCIe being disabled.
Supply voltages are enabled unconditionally.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using internal PHY refclk is not supported yet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB host is an HSIC interface directly connected to a USB hub. USB OTG2
is a direct connection to Mini PCIe interface without any OC signaling.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Split pinctrl as well. 'reset-deassert-us' is added with a small safe
margin.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
make dtbs_check does not warn about this anymore, but bindings mandate
a uint32-matrix.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- assorted prep work for disk space accounting rewrite
- BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
makes our trigger context more explicit
- A few fixes to avoid excessive transaction restarts on multithreaded
workloads: fstests (in addition to ktest tests) are now checking
slowpath counters, and that's shaking out a few bugs
- Assorted tracepoint improvements
- Starting to break up bcachefs_format.h and move on disk types so
they're with the code they belong to; this will make room to start
documenting the on disk format better.
- A few minor fixes
-----BEGIN PGP SIGNATURE-----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=yd+F
-----END PGP SIGNATURE-----
Merge tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs
Pull more bcachefs updates from Kent Overstreet:
"Some fixes, Some refactoring, some minor features:
- Assorted prep work for disk space accounting rewrite
- BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
makes our trigger context more explicit
- A few fixes to avoid excessive transaction restarts on
multithreaded workloads: fstests (in addition to ktest tests) are
now checking slowpath counters, and that's shaking out a few bugs
- Assorted tracepoint improvements
- Starting to break up bcachefs_format.h and move on disk types so
they're with the code they belong to; this will make room to start
documenting the on disk format better.
- A few minor fixes"
* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
bcachefs: Improve inode_to_text()
bcachefs: logged_ops_format.h
bcachefs: reflink_format.h
bcachefs; extents_format.h
bcachefs: ec_format.h
bcachefs: subvolume_format.h
bcachefs: snapshot_format.h
bcachefs: alloc_background_format.h
bcachefs: xattr_format.h
bcachefs: dirent_format.h
bcachefs: inode_format.h
bcachefs; quota_format.h
bcachefs: sb-counters_format.h
bcachefs: counters.c -> sb-counters.c
bcachefs: comment bch_subvolume
bcachefs: bch_snapshot::btime
bcachefs: add missing __GFP_NOWARN
bcachefs: opts->compression can now also be applied in the background
bcachefs: Prep work for variable size btree node buffers
bcachefs: grab s_umount only if snapshotting
...
- A fix for the idle and iowait time accounting vs. CPU hotplug.
The time is reset on CPU hotplug which makes the accumulated
systemwide time jump backwards.
- Assorted fixes and improvements for clocksource/event drivers
-----BEGIN PGP SIGNATURE-----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=RD6E
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for time and clocksources:
- A fix for the idle and iowait time accounting vs CPU hotplug.
The time is reset on CPU hotplug which makes the accumulated
systemwide time jump backwards.
- Assorted fixes and improvements for clocksource/event drivers"
* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
clocksource/drivers/ep93xx: Fix error handling during probe
clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
clocksource/timer-riscv: Add riscv_clock_shutdown callback
dt-bindings: timer: Add StarFive JH8100 clint
dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs
- 18f14afe28 powerpc/64s: Increase default stack size to 32KB BY: Michael Ellerman
Thanks to:
Michael Ellerman
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTYs9CDOrDQRwKRmtrJvCLnGrjHVgUCZayxkgAKCRDJvCLnGrjH
Vv2hAQDwvyYydFw64D7bnaFJDLvOwi3SL02OBaFYV1JTr8rf/QEA8NcTuqXis5o5
NedFYVE5PhYGWfyPD63aL+JpUKxsXwc=
=Ud9v
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Aneesh Kumar:
- Increase default stack size to 32KB for Book3S
Thanks to Michael Ellerman.
* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Increase default stack size to 32KB
