rt1711h_probe() registers the TCPCI port before requesting the interrupt
and enabling alert interrupts. If either of those later steps fails, the
probe function returns without unregistering the TCPCI port. The explicit
unregister currently only happens from the remove callback.
Register a devres action immediately after tcpci_register_port() succeeds,
so tcpci_unregister_port() runs on later probe failures and on driver
detach. Drop the remove callback to avoid unregistering the same port
twice.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: 302c570bf3 ("usb: typec: tcpci_rt1711h: avoid screaming irq causing boot hangs")
Cc: stable <stable@kernel.org>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Link: https://patch.msgid.link/20260706145312.37260-1-mhun512@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VDO() second parameter is VDM type (bit 15): 1 for SVDM, 0 for UVDM.
Using 'vdo ? 2 : 1' corrupts SVID low bit when vdo is non-NULL
(2 << 15 = BIT(16)). Enter Mode is always SVDM, hardcode to 1.
Fixes: 8face9aa57 ("usb: typec: Add parameter for the VDO to typec_altmode_enter()")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260604105059.18750-1-andyshrk@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a Dell XPS 13 9360 (BIOS 2.21.0), entering system suspend (deep/S3)
races a pending UCSI connector-change worker against the ACPI EC teardown.
The worker evaluates the UCSI _DSM (GET_CONNECTOR_STATUS), whose AML
accesses the Embedded Controller. By that point the ACPI EC has already
been stopped for suspend, so the EC address space handler rejects the
access with AE_BAD_PARAMETER, aborting the AML and failing the connector
query:
[22314.689495] ACPI: EC: interrupt blocked
[22314.711981] ACPI: PM: Preparing to enter system sleep state S3
[22314.743260] ACPI: EC: event blocked
[22314.743265] ACPI: EC: EC stopped
[22314.743267] ACPI: PM: Saving platform NVS memory
[22314.744241] ACPI Error: AE_BAD_PARAMETER, Returned by Handler for [EmbeddedControl] (20260408/evregion-303)
[22314.744432] ACPI Error: Aborting method \_SB.PCI0.LPCB.ECDV.ECW1 due to previous error (AE_BAD_PARAMETER) (20260408/psparse-543)
[22314.744673] ACPI Error: Aborting method \ECWB due to previous error (AE_BAD_PARAMETER) (20260408/psparse-543)
[22314.745201] ACPI Error: Aborting method \_SB.UBTC._DSM due to previous error (AE_BAD_PARAMETER) (20260408/psparse-543)
[22314.745394] ACPI: \_SB_.UBTC: failed to evaluate _DSM c298836f-a47c-e411-ad36-631042b5008f rev:1 func:1 (0x1001)
[22314.745414] ucsi_acpi USBC000:00: ucsi_acpi_dsm: failed to evaluate _DSM 1
[22314.745424] ucsi_acpi USBC000:00: ucsi_handle_connector_change: GET_CONNECTOR_STATUS failed (-5)
ucsi_acpi implements a resume callback but no suspend callback, so nothing
cancels the connector-change work before the firmware/EC is torn down.
Add a `ucsi_suspend()` core helper that cancels the pending init and
connector-change work, and wire it into ucsi_acpi's PM ops. The connector
state is re-read on resume by `ucsi_resume()`, so cancelling the work loses
nothing.
Fixes: 4e3a50293c ("usb: typec: ucsi: acpi: Implement resume callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Assisted-by: Claude Opus 4.8
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260703110738.8457-2-pmenzel@molgen.mpg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_power_delivery_find() wraps class_find_device_by_name(). That helper
returns a device reference that must be released by the caller.
select_usb_power_delivery_store() only needs this reference while calling
the pd_set callback. Drop it once the callback returns. Otherwise the sysfs
write can pin the selected USB Power Delivery object and prevent it from
being released on unregister.
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable <stable@kernel.org>
Signed-off-by: Shuangpeng Bai <shuangpeng.kernel@gmail.com>
Link: https://patch.msgid.link/20260702191329.2648043-1-shuangpeng.kernel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6bebd9b777 ("usb: typec: ps883x: Rework ps883x_set()") introduced
two regressions:
1. The CONN_STATUS_0_USB_3_1_CONNECTED bit is mistakenly written to the
wrong configuration register (cfg1 instead of cfg0). This breaks USB3
when using USB3+DP adapters.
2. The switch-case fallthrough block is inverted: Currently,
TYPEC_DP_STATE_C (DP-only) inherits the USB3 configuration, while
TYPEC_DP_STATE_D (DP+USB3) is missing the necessary DP sink flags.
Fix these by writing the USB3 bit to the correct register and swapping the
case statement order so both states get their correct bits assigned.
Cc: stable <stable@kernel.org>
Fixes: 6bebd9b777 ("usb: typec: ps883x: Rework ps883x_set()")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260601-ps883x-usb3dp-fixes-v1-1-d19bec3a6d26@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device with active stream endpoints is disconnected,
xhci_free_streams() is called from the hub_event workqueue to
free the stream resources. It calls xhci_free_stream_info()
while holding xhci->lock with irqs disabled.
xhci_free_stream_info() invokes xhci_free_stream_ctx(), which
calls dma_free_coherent() for large stream context arrays.
dma_free_coherent() can sleep (e.g. via vunmap), triggering
a BUG when called from atomic context.
Call trace:
dma_free_attrs+0x174/0x220
xhci_free_stream_info+0xd0/0x11c
xhci_free_streams+0x278/0x37c
usb_free_streams+0x98/0xc0
usb_unbind_interface+0x1b8/0x2f8
device_release_driver_internal+0x1d4/0x2cc
device_release_driver+0x18/0x28
bus_remove_device+0x160/0x1a4
device_del+0x1ec/0x350
usb_disable_device+0x98/0x214
usb_disconnect+0xf0/0x35c
hub_event+0xab4/0x19ec
process_one_work+0x278/0x63c
Fix this by saving the stream_info pointers and clearing the
ep references under the lock, then calling xhci_free_stream_info()
outside the lock where sleeping is allowed.
Fixes: 8df75f42f8 ("USB: xhci: Add memory allocation for USB3 bulk streams.")
Cc: stable <stable@kernel.org>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260703144033.483286-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_ring_to_sgtable() allocates a temporary pages array and
uses it to build the returned sg_table with
sg_alloc_table_from_pages().
The error paths free the pages array, but the success path
returns the sg_table without freeing it. This leaks the temporary
array every time a sideband client gets an endpoint or event ring
buffer.
Free the pages array after sg_alloc_table_from_pages() succeeds.
The returned sg_table has its own scatterlist entries and does not
depend on the temporary array after construction.
Fixes: de66754e9f ("xhci: sideband: add initial api to register a secondary interrupter entity")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260703144033.483286-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc structure acts as the management structure for the gadget,
but their lifecycles are decoupled. A race condition exists where
usb_del_gadget() frees the udc memory (e.g., via mode-switch work)
while gadget_match_driver() concurrently accesses the freed udc memory
(e.g., via configfs), causing a Use-After-Free (UAF) that triggers a
NULL pointer dereference when the freed memory is zeroed:
[39430.908615][ T1171] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[39430.911397][ T1171] pc : __pi_strcmp+0x20/0x140
[39430.911441][ T1171] lr : gadget_match_driver+0x34/0x60
...
[39430.911890][ T1171] usb_gadget_register_driver_owner+0x50/0xf8
[39430.911910][ T1171] gadget_dev_desc_UDC_store+0xf4/0x140
[39430.931308][ T1171] configfs_write_iter+0xec/0x134
[39430.957058][ T1171] Workqueue: events_freezable __dwc3_set_mode
[39430.957287][ T1171] dwc3_gadget_exit+0x34/0x8c
[39430.957304][ T1171] __dwc3_set_mode+0xc0/0x664
Fix this by ensuring the udc structure remains allocated until the
gadget is released. To achieve this, introduce a new
usb_gadget_release() routine to the core. When the gadget is added,
usb_add_gadget() stores the gadget's release routine in the udc
structure and takes a reference to the udc. When the gadget is
released, usb_gadget_release() drops the reference to the udc and
then calls the gadget's release routine.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20260625073705.803880-1-hhhuuu@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3_gadget_suspend() takes dwc->lock with IRQs disabled and then calls
dwc3_disconnect_gadget(). For async callbacks that helper only uses
plain spin_unlock()/spin_lock(), so the gadget ->disconnect() callback
still runs with IRQs disabled and any sleepable callback trips Lockdep.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the dwc3_gadget_suspend() ->
dwc3_disconnect_gadget() -> gadget_driver->disconnect() chain, and
Lockdep reported:
BUG: sleeping function called from invalid context
gadget_disconnect+0x21/0x39 [vuln_msv]
dwc3_gadget_suspend.constprop.0+0x2b/0x42 [vuln_msv]
Keep the disconnect callback selection in one common helper, but add a
sleepable suspend-side wrapper which snapshots the callback under
dwc->lock and then runs it after spin_unlock_irqrestore(). The regular
event path still uses the existing spin_unlock()/spin_lock() window.
Fixes: c8540870af ("usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()")
Cc: stable <stable@kernel.org>
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260612052005.3849659-1-runyu.xiao@seu.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sl811h_probe() enables the HCD controller device as a wakeup source after
usb_add_hcd() succeeds, but sl811h_remove() removes the HCD and releases
the driver resources without disabling that wakeup source.
Disable controller wakeup after usb_remove_hcd() and before usb_put_hcd()
so the wakeup source object is detached while the controller device pointer
is still available.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: 3c9740a117 ("usb: hcd: move controller wakeup setting initialization to individual driver")
Cc: stable <stable@kernel.org>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Link: https://patch.msgid.link/20260701121625.96815-1-mhun512@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
anx7411_i2c_probe() enables runtime PM before returning successfully, but
anx7411_i2c_remove() tears down the Type-C partner state, workqueue, dummy
I2C device, mux, switch and port without disabling runtime PM.
Use devm_pm_runtime_enable() so runtime PM is disabled automatically on
driver detach. Since devres action registration can fail, route that
failure through the existing probe unwind path.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Cc: stable <stable@kernel.org>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260701114006.75738-1-mhun512@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3_ulpi_setup() calls the register read and write calls with
dwc3->regs when both these calls take the dwc3 structure directly.
Chnage these two calls to fix the following sparse warning, and
possibly a nasty bug in the dwc3_ulpi_setup() code:
drivers/usb/dwc3/core.c:796:45: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/core.c:796:45: expected struct dwc3 *dwc
drivers/usb/dwc3/core.c:796:45: got void [noderef] __iomem *regs
drivers/usb/dwc3/core.c:798:40: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/core.c:798:40: expected struct dwc3 *dwc
drivers/usb/dwc3/core.c:798:40: got void [noderef] __iomem *regs
Cc: stable <stable@kernel.org>
Fixes: 9accc68b1c ("usb: dwc3: Add dwc pointer to dwc3_readl/writel")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://patch.msgid.link/20260703162033.2847599-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uss720_probe() registers a parport before reading the 1284 register used
to detect unsupported Belkin F5U002 adapters. If get_1284_register()
fails, the error path drops the driver private data and the USB device
reference, but leaves the parport device registered.
Leaving the port registered is more than a private allocation leak:
parport_register_port() has already reserved a parport number and
registered the parport bus device, while pp->private_data still points at
the private data that the common error path is about to release.
Undo the pre-announce registration in the get_1284_register() failure
branch before jumping to the common private-data cleanup path. Clear
priv->pp first, matching the disconnect path and avoiding a stale pointer
in the private data.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: 3295f1b866 ("usb: misc: uss720: check for incompatible versions of the Belkin F5U002")
Cc: stable <stable@kernel.org>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Reviewed-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://patch.msgid.link/20260706151049.63470-1-mhun512@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a length check for the rndis header in rndis_rm_hdr, to ensure that
MessageType, MessageLength, DataOffset, and DataLength fields are
present before they are accessed.
Assisted-by: gkh_clanker_2000
Cc: stable <stable@kernel.org>
Signed-off-by: Griffin Kroah-Hartman <griffin@kroah.com>
Link: https://patch.msgid.link/20260708-usb-gadget-rndis-v1-2-e77e026dcc6a@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add variable representations for BufLength and BufOffset in
rndis_query_response(), and perform a length check on them.
This is identical to how rndis_set_response() handles these parameters.
Assisted-by: gkh_clanker_2000
Cc: stable <stable@kernel.org>
Signed-off-by: Griffin Kroah-Hartman <griffin@kroah.com>
Link: https://patch.msgid.link/20260708-usb-gadget-rndis-v1-1-e77e026dcc6a@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EHCI and FOTG210 isochronous submits build an ehci_iso_sched before
linking the URB to the endpoint queue, and keep the staged schedule in
urb->hcpriv until iso_stream_schedule() and the link helpers consume it.
If the controller is no longer accessible, or usb_hcd_link_urb_to_ep()
fails, submit jumps to done_not_linked before that handoff happens and
leaks the staged schedule still attached to urb->hcpriv.
Free the staged schedule from done_not_linked when submit fails before
the URB is linked and clear urb->hcpriv after the free.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1.1.
An x86_64 allyesconfig build showed no new warnings. As we do not have an
EHCI host controller with a USB isochronous device to test with, no
runtime testing was able to be performed.
Fixes: 8de9840265 ("[PATCH] USB: Fix USB suspend/resume crasher (#2)")
Fixes: e9df41c5c5 ("USB: make HCDs responsible for managing endpoint queues")
Fixes: 7d50195f6c ("usb: host: Faraday fotg210-hcd driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20260630071419.349161-1-dawei.feng@seu.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1892bf9067 ("USB: usb-storage: Fix use of bitfields for
hardware data in ene_ub6250.c") converted the media status fields from
bitfields to bit masks.
The original ene_transport() test called ene_init() only when neither
media type was ready:
!(sd_ready || ms_ready)
The converted test became:
!sd_ready || ms_ready
This is not equivalent. Restore the original semantics by testing that
both ready bits are clear before calling ene_init().
Fixes: 1892bf9067 ("USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/F42641386E32404F+20260626070607.4119527-1-raoxu@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
printer_open() returns -EBUSY when the character device is already
open, but it increments dev->kref regardless of the return value. VFS
does not call ->release() for a failed open, so every rejected second
open permanently leaks one reference.
Move kref_get() into the successful-open branch.
Fixes: e8d5f92b8d ("usb: gadget: function: printer: fix use-after-free in __lock_acquire")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Link: https://patch.msgid.link/80295742B820DA9B+20260626064617.4090626-1-raoxu@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vep_alloc_request() wasn't initializing vrequest->udc, so cancellations
on the FunctionFS AIO path were arriving in vep_dequeue without a valid
UDC reference.
Since vrequest->udc is never actually properly used anywhere, we opt to
remove it, and update vep_dequeue to obtain a reference to the udc with
ep_to_vudc(), consistent with the other vep_ ops.
AFAICT this bug has existed for ~10 years. Seems that nobody has really
stressed the FunctionFS AIO path on usbip's vudc.
I tested this fix in a QEMU aarch64 guest driving FunctionFS endpoints
via AIO. Before the fix, running `usbip attach` from the host would
cause the guest to oops with the following backtrace:
Call trace:
vep_dequeue+0x1c/0xe4 (P)
usb_ep_dequeue+0x14/0x20
ffs_aio_cancel+0x24/0x34
__arm64_sys_io_cancel+0xb0/0x124
do_el0_svc+0x68/0x100
el0_svc+0x18/0x5c
el0t_64_sync_handler+0x98/0xdc
el0t_64_sync+0x154/0x158
Assisted-by: opencode:openai/gpt-5.5
Cc: stable <stable@kernel.org>
Fixes: b6a0ca1118 ("usbip: vudc: Add UDC specific ops")
Reviewed-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20260626-usbip-vudc-deque-fix-v3-1-98c2dc4d6a48@samcday.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB devices running at SuperSpeedPlus report "10000" or "20000" in
their sysfs speed attribute. usbip currently maps only "5000" to
USB_SPEED_SUPER, so a SuperSpeedPlus device is imported as
USB_SPEED_UNKNOWN.
The attach request is then rejected by vhci_hcd:
vhci_hcd: Failed attach request for unsupported USB speed: UNKNOWN
Map the SuperSpeedPlus sysfs speed values to USB_SPEED_SUPER_PLUS, use
the SuperSpeed VHCI hub for SuperSpeedPlus devices, and recognize the
gadget current_speed string used by the kernel.
Fixes: b2316645ca ("usb: show speed "10000" in sysfs for USB 3.1 SuperSpeedPlus devices")
Cc: stable <stable@kernel.org>
Signed-off-by: Yichong Chen <chenyichong@uniontech.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://patch.msgid.link/00C828F338E43447+20260617020613.199086-1-chenyichong@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the UCSI Specification Revision 3.1 RC1, bits 32-63 of the SET_NEW_CAM
command hold the 32-bit Alternate Mode Specific (AMSpecific) field.
For DisplayPort Alternate Mode, this field must contain the full
32-bit DisplayPort configuration VDO payload that the OPM wants the
connector to operate in, rather than just the pin assignment value.
This AMSpecific value follows the DisplayPort Configurations defined
in the DisplayPort Alt Mode on USB Type-C Specification v2.1a,
Table 5-13: SOP DisplayPort Configurations.
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Jameson Thies <jthies@google.com>
Reviewed-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260619153311.3526083-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a fix for an information leak in the keyspan_pda driver and
three fixes for digi_acceleport addressing stuck rx if a port is closed
while throttled, a hard lockup on disconnect and write buffer
corruption.
Included are also some new modem device ids.
All have been in linux-next for a few days with no reported issues.
-----BEGIN PGP SIGNATURE-----
iJEEABYKADkWIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCakd3IxsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMiwyLDIACgkQC8XNwux9ZQhbZAEAwMNsbp0cXHxNt1ork9xu
dxPabcqTYZ5FwOEGktY7k4oA+we0wwuk/5862uDVzG+hNESL65XIDfuPrtLq7l1C
4ZoO
=ZNNY
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-7.2-rc2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB serial fixes for 7.2-rc2
Here is a fix for an information leak in the keyspan_pda driver and
three fixes for digi_acceleport addressing stuck rx if a port is closed
while throttled, a hard lockup on disconnect and write buffer
corruption.
Included are also some new modem device ids.
All have been in linux-next for a few days with no reported issues.
* tag 'usb-serial-7.2-rc2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: keyspan_pda: fix information leak
USB: serial: option: add Telit Cinterion FE990D50 compositions
USB: serial: digi_acceleport: fix broken rx after throttle
USB: serial: digi_acceleport: fix hard lockup on disconnect
USB: serial: digi_acceleport: fix write buffer corruption
The write() callback is supposed to return the number of characters
accepted or a negative errno. Since the addition of write fifo support
the keyspan_pda implementation will however return the number characters
submitted to the device if the write urb is not already in use. If this
number is larger than the number of characters passed to write(), the
line discipline continues writing data from beyond the tty write buffer.
Fix the information leak by making sure that keyspan_pda_write_start()
returns zero on success as intended.
Fixes: 034e38e8f6 ("USB: serial: keyspan_pda: add write-fifo support")
Cc: stable@vger.kernel.org # 5.11
Signed-off-by: Johan Hovold <johan@kernel.org>
If the port is closed while throttled, the read urb is never resubmitted
and the port will not receive any further data until the device is
reconnected (or the driver is rebound).
Clear the throttle flags and submit the urb if needed when opening the
port.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
If submitting the OOB write urb fails persistently (e.g if the device is
being disconnected) the driver would loop indefinitely with interrupts
disabled.
Check for urb submission errors when sending OOB commands to avoid
hanging if, for example, open(), set_termios() or close() races with a
physical disconnect.
This is issue was flagged by Sashiko when reviewing an unrelated change
to the driver.
Link: https://sashiko.dev/#/patchset/20260610132232.356139-1-johan%40kernel.org?part=1
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The digi_write_inb_command() is supposed to wait for the write urb to
become available or return an error, but instead it updates the transfer
buffer and tries to resubmit the urb on timeout.
To make things worse, for commands like break control where no timeout
is used, the driver would corrupt the urb immediately due to a broken
jiffies comparison (on 32-bit machines this takes five minutes of uptime
to trigger due to INITIAL_JIFFIES).
Fix this by adding the missing return on timeout and waiting
indefinitely when no timeout has been specified as intended.
This issue was (sort of) flagged by Sashiko when reviewing an unrelated
change to the driver.
Link: https://sashiko.dev/#/patchset/20260610132232.356139-1-johan%40kernel.org?part=11
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
As was recently noted on the rust-for-linux list, the usb.rs file is not
listed as part of the USB SUBSYSTEM files, which can cause changes to it
to be not sent to the proper list and people. Fix this up by adding it
to the USB SUBSYSTEM file list
Reported-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patch.msgid.link/2026062533-achiness-outsell-a93a@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbio_bulk_msg() copies bpkt_len = le16_to_cpu(bpkt->len) bytes out of
the bulk IN buffer (usbio->rxbuf, allocated with size usbio->rxbuf_len)
into the caller's buffer. bpkt_len is fully controlled by the device
and is only checked against ibuf_len; ibuf_len in turn is checked
against usbio->txbuf_len, not against rxbuf_len:
if ((obuf_len > (usbio->txbuf_len - sizeof(*bpkt))) ||
(ibuf_len > (usbio->txbuf_len - sizeof(*bpkt))))
return -EMSGSIZE;
txbuf_len and rxbuf_len are taken independently from the bulk OUT and
bulk IN endpoint wMaxPacketSize in usbio_probe(). A malicious or
malfunctioning device that advertises a large bulk OUT endpoint and a
small bulk IN endpoint (e.g. by claiming one of the quirk-free IDs such
as the Lattice NX33U, 0x2ac1:0x20cb) therefore makes ibuf_len, and
hence the device-supplied bpkt_len, exceed rxbuf_len. memcpy() then
reads up to txbuf_len - rxbuf_len bytes past the end of the rxbuf slab
object. The over-read bytes are handed back to the i2c layer and on to
user space through i2c-dev, disclosing adjacent slab memory; with KASAN
this is reported as a slab-out-of-bounds read.
The number of bytes actually received is already known: act equals the
URB actual_length and is bounded by rxbuf_len. Reject any response
that claims more payload than was received, mirroring the existing
"act < sizeof(*bpkt)" check just above.
The control path (usbio_ctrl_msg()) is not affected: it uses a single
buffer (ctrlbuf) for both directions, so its analogous copy can never
leave the allocation.
Found by code review. The out-of-bounds read was confirmed under
AddressSanitizer with a faithful userspace model of usbio_bulk_msg()'s
receive path (an rxbuf_len-sized buffer, the same act/ibuf_len/bpkt_len
checks and the memcpy). A USB raw-gadget + dummy_hcd reproducer is
also available.
Fixes: 121a0f839d ("usb: misc: Add Intel USBIO bridge driver")
Cc: stable <stable@kernel.org>
Signed-off-by: HE WEI (ギカク) <skyexpoc@gmail.com>
Link: https://patch.msgid.link/20260624090952.86439-1-skyexpoc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mtu3_gadget_queue() maps the request before checking whether
the QMU GPD ring can accept another transfer. the request is
returned with -EAGAIN before it is linked on the endpoint
request list if mtu3_prepare_transfer() fails.
Normal completion and dequeue paths unmap requests from
mtu3_req_complete(), but this error path never reaches that
helper, so the DMA mapping is left active. Unmap the request
before returning from the failed queue path.
Fixes: df2069acb0 ("usb: Add MediaTek USB3 DRD driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20260623093325.2105323-1-haoxiang_li2024@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3_meson_g12a_resume() succeeds in calling
reset_control_reset(), an internal triggered_count reference is
acquired. If any later step fails (usb_init, phy_init,
phy_power_on, regulator_enable, or usb_post_init), the function
returns the error without rearming the reset control. This leaks
the reference and leaves the reset control in a triggered state,
causing future reset_control_reset() calls to incorrectly return
early as if already reset.
Add an error path that calls reset_control_rearm() to balance
the reference before returning the error.
Cc: stable <stable@kernel.org>
Fixes: 5b0ba0caaf ("usb: dwc3: meson-g12a: refactor usb init")
Signed-off-by: WenTao Liang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20260611131121.81784-1-vulab@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OTG branch of composite_setup() falls back to the first
configuration when none is selected:
if (cdev->config)
config = cdev->config;
else
config = list_first_entry(&cdev->configs,
struct usb_configuration, list);
if (!config)
goto done;
...
memcpy(req->buf, config->descriptors[0], value);
list_first_entry() never returns NULL. On an empty list it returns
container_of() of the list head. So the "if (!config)" check is dead.
When cdev->configs is empty, config points at the head inside struct
usb_composite_dev. config->descriptors[0] reads whatever sits at that
offset. The memcpy copies up to w_length bytes of it into the response
buffer.
cdev->configs can be empty in two cases. One is a teardown race on
gadget unbind with a control transfer in flight. The other is a driver
that sets is_otg before it adds a config. A reproducer that holds
cdev->configs empty triggers a KASAN fault in this branch.
Use list_first_entry_or_null() so the existing check does its job.
Fixes: 53e6242db8 ("usb: gadget: composite: add USB_DT_OTG request handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Link: https://patch.msgid.link/20260527150832.2943293-1-maoyixie.tju@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, ffs_epfile_release unconditionally frees the endpoint's
read_buffer when a file descriptor is closed. If userspace explicitly
opens the endpoint multiple times and closes one, the read_buffer is
destroyed. This can lead to silent data loss if other file descriptors
are still actively reading from the endpoint.
By tying the lifetime of the read_buffer to the ffs_epfile structure itself
(which is destroyed when the functionfs instance is torn down in
ffs_epfiles_destroy), we eliminate the brittle dependency on open/release
calls while correctly matching the conceptual lifetime of unread data on
the hardware endpoint.
Fixes: 9353afbbfa ("usb: gadget: f_fs: buffer data from ‘oversized’ OUT requests")
Cc: stable <stable@kernel.org>
Assisted-by: Antigravity:gemini-3.1-pro
Signed-off-by: Neill Kapron <nkapron@google.com>
Link: https://patch.msgid.link/20260619040609.4010746-3-nkapron@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When parsing endpoint descriptors, ffs_data_got_descs() generates the
eps_addrmap which contains the endpoint direction. However, epfile->in
was previously only populated in ffs_func_eps_enable() which executes
upon USB host connection. As a result, early userspace ioctls like
FUNCTIONFS_DMABUF_ATTACH that run before the host connects would see
epfile->in as 0, leading to incorrect DMA directions.
By moving the initialization to ffs_epfiles_create(), epfile->in is
accurate before userspace opens the endpoint files.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Cc: stable <stable@kernel.org>
Assisted-by: Antigravity:gemini-3.1-pro
Signed-off-by: Neill Kapron <nkapron@google.com>
Link: https://patch.msgid.link/20260619040609.4010746-2-nkapron@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The threaded IRQ handler ccg_irq_handler() calls ucsi_notify_common(),
which on a connector-change event calls ucsi_connector_change() and
schedules connector work. In ucsi_ccg_remove(), ucsi_destroy() frees
uc->ucsi (kfree) before free_irq() is called, so a handler invocation
already in flight may access the freed object after ucsi_destroy().
CPU 0 (remove) | CPU 1 (threaded IRQ)
ucsi_destroy(uc->ucsi) | ccg_irq_handler()
kfree(ucsi) // FREE | ucsi_notify_common(uc->ucsi) // USE
Move free_irq() before ucsi_destroy() in the remove path. It is kept
after ucsi_unregister(): ucsi_unregister() cancels connector work whose
handler issues GET_CONNECTOR_STATUS through ucsi_send_command_common(),
which waits for a completion that is signalled from the IRQ handler, so
the IRQ must stay active until that work has been cancelled.
The probe error path already orders free_irq() before ucsi_destroy().
This bug was found by static analysis.
Fixes: e32fd989ac ("usb: typec: ucsi: ccg: Move to the new API")
Cc: stable <stable@kernel.org>
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260616132011.103279-1-fanwu01@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In svdm_consume_modes(), the SVID value is read from pmdata->svids using
pmdata->svid_index as an array index without bounds validation:
paltmode->svid = pmdata->svids[pmdata->svid_index];
If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results
in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data
is embedded inside struct tcpm_port, indexing past svids reads into
adjacent fields. In particular:
- At index 16, it reads the altmodes count.
- At index 18 and beyond, it reads into altmode_desc[], which contains
partner-supplied SVDM Discovery Modes VDOs.
By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index
to 20, the partner can force paltmode->svid to be loaded with an arbitrary,
partner- chosen SVID, which is then registered via
typec_partner_register_altmode().
Fix this by validating that pmdata->svid_index is non-negative and strictly
less than pmdata->nsvids before accessing the pmdata->svids array inside
svdm_consume_modes().
Assisted-by: Antigravity:gemini-3.5-flash
Fixes: 4ab8c18d4d ("usb: typec: Register a device for every mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260622220803.305750-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9b ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: 18bcbcfe9c ("USB: misc: legousbtower: semaphore to mutex")
Cc: stable <stable@kernel.org>
Cc: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9b ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: ce0d7d3f57 ("usb: ldusb: ld_usb semaphore to mutex")
Cc: stable <stable@kernel.org>
Cc: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9b ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: 54d2bc068f ("USB: fix locking in idmouse")
Cc: stable@vger.kernel.org # 2.6.24
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34 ("locking/mutex: Document that mutex_unlock() is non-atomic")
[2] 2b9d9e0a9b ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@kernel.org>
Reported-by: Yue Sun <samsun1006219@gmail.com>
Link: https://lore.kernel.org/r/20260618080204.38322-1-samsun1006219@gmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ffs_fs_kill_sb() unconditionally calls cancel_work_sync() on
ffs->reset_work when a functionfs instance is unmounted:
ffs_data_reset(ffs);
cancel_work_sync(&ffs->reset_work);
However ffs->reset_work is only ever initialized via INIT_WORK() in
ffs_func_set_alt() and ffs_func_disable(), and only on the
FFS_DEACTIVATED path. That state is reached solely by ffs_data_closed()
when the instance is mounted with the "no_disconnect" option, so for the
common case (no "no_disconnect", or mounted and unmounted without ever
being deactivated) reset_work is never initialized.
ffs_data_new() allocates the ffs_data with kzalloc_obj() and does not
initialize reset_work, and ffs_data_reset()/ffs_data_clear() do not touch
it either, so reset_work.func is left NULL. cancel_work_sync() on such a
work then trips the WARN_ON(!work->func) guard in __flush_work():
WARNING: kernel/workqueue.c:4301 at __flush_work+0x330/0x360, CPU#3: umount
Call trace:
__flush_work
cancel_work_sync
ffs_fs_kill_sb [usb_f_fs]
deactivate_locked_super
deactivate_super
cleanup_mnt
__cleanup_mnt
task_work_run
exit_to_user_mode_loop
el0_svc
On older kernels cancel_work_sync() on a zero-initialized work struct was
a silent no-op, which hid the missing initialization.
Initialize reset_work once in ffs_data_new() so it is always valid for
the lifetime of the ffs_data, and drop the now-redundant INIT_WORK()
calls from the two deactivation paths.
Fixes: 18d6b32fca ("usb: gadget: f_fs: add "no_disconnect" mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Tyler Baker <tyler.baker@oss.qualcomm.com>
Cc: Loic Poulain <loic.poulain@oss.qualcomm.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Michał Nazarewicz <mina86@mina86.com>
Link: https://patch.msgid.link/20260609193635.2284430-1-tyler.baker@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdnsp_alloc_stream_info() allocates stream_info->stream_ctx_array with
cdnsp_alloc_stream_ctx(). If a later stream ring allocation or stream
mapping update fails, the error path frees the allocated stream rings
and stream_rings array, but leaves stream_ctx_array allocated.
Free the stream context array before falling through to the stream_rings
cleanup path.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://patch.msgid.link/20260622052627.696373-1-haoxiang_li2024@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ffs_dmabuf_transfer(), a ffs_dma_fence object is kmalloc'd, with the
underlying dma_fence later initialized by dma_fence_init(), which sets
its kref counter to 1. Then, dma_resv_add_fence() gets a second
reference, and a pointer to the ffs_dma_fence is passed as the
usb_request's "context" field.
The dma-resv mechanism will manage the second reference, but the first
reference is never properly released; the ffs_dmabuf_cleanup() function
decreases the reference count, but only to balance with the reference
grab in ffs_dmabuf_signal_done().
The code will then slowly leak memory as more ffs_dma_fence objects are
created without being ever freed.
Address this issue by transferring ownership of the fence to the DMA
reservation object, by calling dma_fence_put() right after
dma_resv_add_fence(). The ffs_dma_fence then gets properly discarded
after being signalled.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Cc: stable <stable@kernel.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20260609152905.729328-1-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing implementation assigned these flags backwards, configuring
the partner's DisplayPort role to match the port's role instead of
complementing it.
This prevents proper configuration during DP altmode activation, often
causing `pin_assignment` to remain 0 in `dp_altmode_configure()` and
resulting in VDM negotiation failures:
[ 583.328246] typec port1.1: VDM 0xff01a150 failed
Additionally, the fix ensures that the `pin_assignment` sysfs attribute
displays the correct values.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260601142837.3240207-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The allocated device name is never freed on early ULPI device
registration failures.
Fix this by initialising the device structure earlier and releasing the
initial reference whenever registration fails.
Fixes: 289fcff4bc ("usb: add bus type for USB ULPI")
Cc: stable <stable@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260608145803.69360-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_stor_adjust_quirks() parses the usb-storage.quirks module
parameter into a new flag set and then applies it with the quirk
mask to override built-in flags.
The mask is meant to cover the flags that can be overridden by
the module parameter. The 'k' quirk character sets US_FL_NO_SAME,
but US_FL_NO_SAME is not included in the mask.
As a result, the module parameter can set US_FL_NO_SAME, but it
cannot clear a built-in US_FL_NO_SAME flag by providing an override
entry that omits 'k'.
Add US_FL_NO_SAME to the mask so that the module parameter can
override it in the same way as the other supported flags.
Fixes: 8010622c86 ("USB: UAS: introduce a quirk to set no_write_same")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/3BCE5880F9A45C2E+20260602053842.2920137-1-raoxu@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VIA Labs, Inc. USB 2.0 hub controller (2109:2817),
found in a KVM switch, fails to enumerate high-power devices during
cold boot and system restart.
Applying the kernel parameter
usbcore.quirks=2109:2817:k
resolves the issue.
Enumeration failure log:
usb 1-1.2.3: device descriptor read/64, error -32
usb 1-1.2.3: Device not responding to setup address.
usb 1-1.2.3: device not accepting address 11, error -71
usb 1-1.2-port3: unable to enumerate USB device
Add USB_QUIRK_NO_LPM for this device.
Signed-off-by: Rodrigo Lugathe da Conceição Alves <lugathe2@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260603113626.395612-1-lugathe2@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Samsung T5 EVO Portable SSD (04e8:6200) exhibit two forms of
link instability when USB Link Power Management is enabled:
1. The units fail to initialize properly on first detection,
resulting in a lockup in the drive where it must be power cycled
or the kernel will not recognize the presence of the device.
2. If used for sustained operations (small amounts of continuous
data are transferred to the unit) then the unit will "hiccup"
after roughly 8 hours of use and will disconnect and reconnect.
This has a certain probability of triggering the first issue,
but also causes mount points to become invalid since the device
gets issued a new letter.
Signed-off-by: Erich E. Hoover <erich.e.hoover@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260602204508.48856-1-erich.e.hoover@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
