Some network drivers use __dev_mc_sync()/__dev_uc_sync() and therefore
program the hardware only with addresses with a non-zero sync_cnt.
Some of the above drivers also need to save/restore the address
filtering lists when certain events happen, and they need to walk
through the struct net_device :: uc and struct net_device :: mc lists.
But these lists contain unsynced addresses too.
To keep the appearance of an elementary form of data encapsulation,
provide iterators through these lists that only look at entries with a
non-zero sync_cnt, instead of filtering entries out from device drivers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
ice: L2TPv3 offload support
Wojciech Drewek says:
Add support for dissecting L2TPv3 session id in flow dissector. Add support
for this field in tc-flower and support offloading L2TPv3. Finally, add
support for hardware offload of L2TPv3 packets based on session id in
switchdev mode in ice driver.
Example filter:
# tc filter add dev $PF1 ingress prio 1 protocol ip \
flower \
ip_proto l2tp \
l2tpv3_sid 1234 \
skip_sw \
action mirred egress redirect dev $VF1_PR
Changes in iproute2 are required to use the new fields.
ICE COMMS DDP package is required to create a filter in ice.
COMMS DDP package contains profiles of more advanced protocols.
Without COMMS DDP package hw offload will not work, however
sw offload will still work.
====================
Link: https://lore.kernel.org/r/20220908171644.1282191-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for offloading packets based on L2TPv3 session id in switchdev
mode.
Example filter:
tc filter add dev $PF1 ingress prio 1 protocol ip flower ip_proto l2tp \
l2tpv3_sid 1234 skip_sw action mirred egress redirect dev $VF1_PR
Changes in iproute2 are required to be able to specify l2tpv3_sid.
ICE COMMS DDP package is required to create a filter as it contains L2TPv3
profiles.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Allow to offload L2TPv3 filters by adding flow_rule_match_l2tpv3.
Drivers can extract L2TPv3 specific fields from now on.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for matching on L2TPv3 session ID.
Session ID can be specified only when ip proto was
set to IPPROTO_L2TP.
Example filter:
# tc filter add dev $PF1 ingress prio 1 protocol ip \
flower \
ip_proto l2tp \
l2tpv3_sid 1234 \
skip_sw \
action mirred egress redirect dev $VF1_PR
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Allow to dissect L2TPv3 specific field which is:
- session ID (32 bits)
L2TPv3 might be transported over IP or over UDP,
this implementation is only about L2TPv3 over IP.
IP protocol carries L2TPv3 when ip_proto is
IPPROTO_L2TP (115).
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
IPPROTO_L2TP is currently defined in l2tp.h, but most of
ip protocols are defined in in.h file. Move it there in order
to keep code clean.
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
coccinelle reports a warning
WARNING: casting value returned by memory allocation
function to (struct octep_rx_buffer *) is useless.
To fix this the useless cast is removed.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/Yx+sr9o0uylXVcOl@playground
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All usages of the vport_ops struct have the .send field set to
dev_queue_xmit or internal_dev_recv. Since most usages are set to
dev_queue_xmit, the function hook should match the signature of
dev_queue_xmit.
The only call to vport_ops->send() is in net/openvswitch/vport.c and it
throws away the return value.
This mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220913230739.228313-1-nhuck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit field in net_device_ops is expected to be of type
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev).
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of t7xx_ccmni_start_xmit should be changed from int to
netdev_tx_t.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://lore.kernel.org/r/20220912214510.929070-1-nhuck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit field in net_device_ops is expected to be of type
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev).
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of ipc_wwan_link_transmit should be changed from int to
netdev_tx_t.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://lore.kernel.org/r/20220912214455.929028-1-nhuck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit field in net_device_ops is expected to be of type
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev).
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of korina_send_packet should be changed from int to
netdev_tx_t.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220912214344.928925-1-nhuck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit field in net_device_ops is expected to be of type
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev).
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of liteeth_start_xmit should be changed from int to
netdev_tx_t.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20220912195307.812229-1-nhuck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit field in net_device_ops is expected to be of type
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev).
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of emac_dev_xmit should be changed from int to
netdev_tx_t.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220912195023.810319-1-nhuck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit field in net_device_ops is expected to be of type
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev).
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of dm9000_start_xmit should be changed from int to
netdev_tx_t.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220912194722.809525-1-nhuck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit field in net_device_ops is expected to be of type
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev).
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of ax88796c_start_xmit should be changed from int to
netdev_tx_t.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Acked-by: Lukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20220912194031.808425-1-nhuck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- bump version strings, by Simon Wunderlich
- drop unused headers in trace.h, by Sven Eckelmann
- drop initialization of flexible ethtool_link_ksettings,
by Sven Eckelmann
- remove unused struct definitions, by Marek Lindner
-----BEGIN PGP SIGNATURE-----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=Fh8v
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-pullrequest-20220916' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- drop unused headers in trace.h, by Sven Eckelmann
- drop initialization of flexible ethtool_link_ksettings,
by Sven Eckelmann
- remove unused struct definitions, by Marek Lindner
* tag 'batadv-next-pullrequest-20220916' of git://git.open-mesh.org/linux-merge:
batman-adv: remove unused struct definitions
batman-adv: Drop initialization of flexible ethtool_link_ksettings
batman-adv: Drop unused headers in trace.h
batman-adv: Start new development cycle
====================
Link: https://lore.kernel.org/r/20220916161454.1413154-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
mlxsw: Adjust QOS tests for Spectrum-4 testing
Amit writes:
Quality Of Service tests create congestion and verify the switch behavior.
To create congestion, they need to have more traffic than the port can
handle, so some of them force 1Gbps speed.
The tests assume that 1Gbps speed is supported. Spectrum-4 ASIC will not
support this speed in all ports, so to be able to run QOS tests there,
some adjustments are required.
Patch set overview:
Patch #1 adjusts qos_ets_strict, qos_mc_aware and sch_ets tests.
Patch #2 adjusts RED tests.
Patch #3 extends devlink_lib to support querying maximum pool size.
Patch #4 adds a test which can be used instead of qos_burst and do not
assume that 1Gbps speed is supported.
Patch #5 removes qos_burst test.
====================
Link: https://lore.kernel.org/r/cover.1663152826.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch added a test which can be used instead of qos_burst.sh.
Remove this test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an equivalent test to qos_burst, the test's purpose is same, but the
new test uses simpler topology and does not require forcing low speed.
In addition, it can be run Spectrum-2 and not only Spectrum-3+. The idea
is to use a shaper in order to limit the traffic and create congestion.
qos_burst test uses small pool, sends many small packets, and verify that
packets are not dropped, which means that many descriptors can be handled.
This test should check the change that commit c864769add
("mlxsw: Configure descriptor buffers") pushed.
Instead, the new test tries to use more than 85% of maximum supported
descriptors. The idea is to use big pool (as much as the ASIC supports),
such that the pool size does not limit the traffic, then send many small
packets, which means that many descriptors are used, and check how many
packets the switch can handle.
The usage of shaper allows to run the test in all ASICs, regardless of
the CPU abilities, as it is able to create the congestion with low rate
of packets.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The maximum pool size is exposed via 'devlink sb' command. The next
patch will add a test which increases some pools to the maximum size.
Add a function to query the value.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
QOS tests create congestion and verify the switch behavior. To create
congestion, they need to have more traffic than the port can handle, so
some of them force 1Gbps speed.
The tests assume that 1Gbps speed is supported, otherwise, they will fail.
Spectrum-4 ASIC will not support this speed in all ports, so to be able
to run the tests there, some adjustments are required. Use shapers to limit
the traffic instead of forcing speed. Note that for several ports, the
speed configuration is just for autoneg issues, so shaper is not needed
instead.
The tests already use ETS qdisc as a root and RED qdiscs as children. Add
a new TBF shaper to limit the rate of traffic, and use it as a root qdisc,
then save the previous hierarchy of qdiscs under the new TBF root.
In some ASICs, the shapers do not limit the traffic as accurately as
forcing speed. To make the tests stable, allow the backlog size to be up to
+-10% of the threshold. The aim of the tests is to make sure that with
backlog << threshold, there are no drops, and that packets are dropped
somewhere in vicinity of the configured threshold.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
QOS tests create congestion and verify the switch behavior. To create
congestion, they need to have more traffic than the port can handle, so
some of them force 1Gbps speed.
The tests assume that 1Gbps speed is supported, otherwise, they will fail.
Spectrum-4 ASIC will not support this speed in all ports, so to be able
to run QOS tests there, some adjustments are required. Use shapers to
limit the traffic instead of forcing speed. Note that for several ports,
the speed configuration is just for autoneg issues, so shaper is not needed
instead.
In tests that already use shapers, set the existing shaper to be a child of
a new TBF shaper which is added as a root qdisc and acts as a port shaper.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Remove label = "cpu" from DSA dt-bindings
As explained in more detail in patch 1/3, label = "cpu" is not part of
DSA's device tree bindings, yet we have some checks in the dt-schema for
mt7530 which are written as if it was.
Reformulate those checks, and remove all occurrences of this seemingly
used, but actually unused, property from the binding examples.
====================
Link: https://lore.kernel.org/r/20220912175058.280386-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is not used by the DSA dt-binding, so remove it from all examples.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The common dsa-port.yaml does this (and more) since commit 2ec2fb8331
("dt-bindings: net: dsa: make phylink bindings required for CPU/DSA
ports").
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fact that some DSA device trees use 'label = "cpu"' for the CPU port
is nothing but blind cargo cult copying. The 'label' property was never
part of the DSA DT bindings for anything except the user ports, where it
provided a hint as to what name the created netdevs should use.
DSA does use the "cpu" port label to identify a CPU port in dsa_port_parse(),
but this is only for non-OF code paths (platform data).
The proper way to identify a CPU port is to look at whether the
'ethernet' phandle is present.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use kmemdup() helper instead of open-coding to
simplify the code when allocate dev_addr.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20220914140100.3795545-2-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Standardized ethtool counters for NXP ENETC
This is another preparation patch for the introduction of MAC Merge
Layer statistics, this time for the enetc driver (endpoint ports on the
NXP LS1028A). The same set of stats groups is supported as in the case
of the Felix DSA switch.
====================
Link: https://lore.kernel.org/r/20220909113800.55225-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Structure the code in such a way that it can be reused later for the
pMAC statistics, by just changing the "mac" argument to 1.
Usage:
ethtool --include-statistics --show-pause eno2
ethtool -S eno0 --groups eth-mac
ethtool -S eno0 --groups eth-ctrl
ethtool -S eno0 --groups rmon
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ENETC has counters for the eMAC and for the pMAC exactly 0x1000
apart from each other. The driver only contains definitions for PM0,
the eMAC.
Rather than duplicating everything for PM1, modify the register
definitions such that they take the MAC as argument.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the Renesas Ethernet AVB (EtherAVB-IF) blocks on R-Car
Gen4 SoCs (e.g. R-Car V4H) by matching on a family-specific compatible
value.
These are treated the same as EtherAVB on R-Car Gen3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/2ee968890feba777e627d781128b074b2c43cddb.1662718171.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geert Uytterhoeven says:
====================
dt-bindings: net: renesas,etheravb: R-Car Gen4 updates
This patch series contains two updates for the Renesas Ethernet AVB
Device Tree bindings.
====================
Link: https://lore.kernel.org/r/cover.1662714607.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document support for the Renesas Ethernet AVB (EtherAVB-IF) block in the
Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence move its compatible value to the R-Car Gen4 section.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wei Fang says:
====================
Add FEC support on s32v234 platform
This series patches are to add FEC support on s32v234 platfom.
1. Add compatible string and quirks for fsl,s32v234
2. Update Kconfig to also check for ARCH_S32.
====================
Link: https://lore.kernel.org/r/20220907095649.3101484-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update Kconfig to also check for ARCH_S32.
Add compatible string and quirks for fsl,s32v234
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add fsl,s32v234-fec to compatible property to support s32v234 platform.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=HdIo
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-net-pinctrl-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Lee Jones says:
====================
Immutable branch between MFD, Net and Pinctrl due for the v6.0 merge window
* tag 'ib-mfd-net-pinctrl-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: ocelot: Add support for the vsc7512 chip via spi
dt-bindings: mfd: ocelot: Add bindings for VSC7512
resource: add define macro for register address resources
pinctrl: microchip-sgpio: add ability to be used in a non-mmio configuration
pinctrl: microchip-sgpio: allow sgpio driver to be used as a module
pinctrl: ocelot: add ability to be used in a non-mmio configuration
net: mdio: mscc-miim: add ability to be used in a non-mmio configuration
mfd: ocelot: Add helper to get regmap from a resource
====================
Link: https://lore.kernel.org/r/YxrjyHcceLOFlT/c@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This node pointer is returned by of_find_compatible_node() with
refcount incremented in this function. of_node_put() on it before
exitting this function.
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Sun Ke <sunke32@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220908040226.871690-1-sunke32@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I found no evidence that this chip version ever made it to the mass
market. Therefore disable detection. Like in similar cases before:
If nobody complains, we'll remove support for this chip version after
few months.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/ac622d4a-ae0a-3817-710f-849db4015c78@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fs_mii_disconnect and fs_mii_connect have been removed since
commit 5b4b845434 ("[PATCH] FS_ENET: use PAL for mii management"),
so remove them.
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220909062959.1144493-1-cuigaosheng1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the reset value of PTP_SEC_ROLLOVER is incorrect on
CNF10KB silicon, the ptp timestamps are inaccurate. This
patch initializes the PTP_SEC_ROLLOVER register properly
for the CNF10KB silicon.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata:
The ptp_clock_hi rollsover to zero one clock cycle before it
reaches one second boundary. As a result, the pps threshold
comparison fails after one second and the pps output signal
won't toggle further.
This patch workarounds the issue by programming the pps_lo_incr
register to 500msec minus one clock cycle period, ensuring that
the pps threshold comparison succeeds at one second rollover
boundary and pps edge toggles. After that point, the driver will
have enough time (~500msec) to reset the pps threshold value.
After each one second boundary, hrtimer is invoked which resets
the pps threshold value.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ptp 1-step mode using timecounter. The seconds and
nanoseconds to be updated in PTP header are calculated by adding the
timecounter offset to the free running PTP clock counter time. The PF
driver periodically gets the PTP clock time using AF mbox. The 1-step
support uses HW feature to update correction field rather than
OriginTimestamp field in PTP header.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
