[ Upstream commit 621735f590 ]
In very rare cases (I've seen two reports so far about different
RTL8125 chip versions) it seems the MAC locks up when link goes down
and requires a software reset to get revived.
Realtek doesn't publish hw errata information, therefore the root cause
is unknown. Realtek vendor drivers do a full hw re-initialization on
each link-up event, the slimmed-down variant here was reported to fix
the issue for the reporting user.
It's not fully clear which parts of the NIC are reset as part of the
software reset, therefore I can't rule out side effects.
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Reported-by: Martin Kjær Jørgensen <me@lagy.org>
Link: https://lore.kernel.org/netdev/97ec2232-3257-316c-c3e7-a08192ce16a6@gmail.com/T/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/9edde757-9c3b-4730-be3b-0ef3a374ff71@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c99626092e ]
The dev->id value comes from ida_alloc() so it's a number between zero
and INT_MAX. If it's too high then these sprintf()s will overflow.
Fixes: 203d3d4aa4 ("the generic thermal sysfs driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de8dd09694 ]
Both usb_kill_urb() and usb_free_urb() do the NULL check itself, so there
is no need to duplicate it prior to calling.
Fixes: a82dfd33d1 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231008025852.1239450-1-ruanjinjie@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f61fe5f081 ]
According to the definition of virtqueue coalescing spec[1]:
Upon disabling and re-enabling a transmit virtqueue, the device MUST set
the coalescing parameters of the virtqueue to those configured through the
VIRTIO_NET_CTRL_NOTF_COAL_TX_SET command, or, if the driver did not set
any TX coalescing parameters, to 0.
Upon disabling and re-enabling a receive virtqueue, the device MUST set
the coalescing parameters of the virtqueue to those configured through the
VIRTIO_NET_CTRL_NOTF_COAL_RX_SET command, or, if the driver did not set
any RX coalescing parameters, to 0.
We need to add this setting for vq resize (ethtool -G) where vq_reset happens.
[1] https://lists.oasis-open.org/archives/virtio-dev/202303/msg00415.html
Fixes: 394bd87764 ("virtio_net: support per queue interrupt coalesce command")
Cc: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfb2b36091 ]
When the user sets a non-zero coalescing parameter to 0 for a specific
virtqueue, it does not work as expected, so let's fix this.
Fixes: 394bd87764 ("virtio_net: support per queue interrupt coalesce command")
Reported-by: Xiaoming Zhao <zxm377917@alibaba-inc.com>
Cc: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9420838ab ]
When using .set_coalesce interface to set all queue coalescing
parameters, we need to update both per-queue and global save values.
Fixes: 394bd87764 ("virtio_net: support per queue interrupt coalesce command")
Cc: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 134674c187 ]
Since virtio-net allows switching napi_tx for per txq, we have to
get the specific txq's result now.
Fixes: 394bd87764 ("virtio_net: support per queue interrupt coalesce command")
Cc: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30fa41a0f6 ]
None of the dump callbacks uses netlink_callback::args beyond the first
element, no need to zero the data.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea2274ab0b ]
When frames are sent over the air, the device always applies the data
rates in descending order. The driver assumed Minstrel also provided
rate in descending order.
However, in some cases, Minstrel can a choose a fallback rate greater
than the primary rate. In this case, the two rates was inverted, the
device try highest rate first and we get many retries.
Since the device always applies rates in descending order, the
workaround is to drop the rate when it higher than its predecessor in
the rate list. Thus [ 4, 5, 3 ] becomes [ 4, 3 ].
This patch has been tested in isolated room with a series of
attenuators. Here are the Minstrel statistics with 80dBm of attenuation:
Without the fix:
best ____________rate__________ ____statistics___ _____last____ ______sum-of________
mode guard # rate [name idx airtime max_tp] [avg(tp) avg(prob)] [retry|suc|att] [#success | #attempts]
HT20 LGI 1 S MCS0 0 1477 5.6 5.2 82.7 3 0 0 3 4
HT20 LGI 1 MCS1 1 738 10.6 0.0 0.0 0 0 0 0 1
HT20 LGI 1 D MCS2 2 492 14.9 13.5 81.5 5 0 0 5 9
HT20 LGI 1 C MCS3 3 369 18.8 17.6 84.3 5 0 0 76 96
HT20 LGI 1 A P MCS4 4 246 25.4 22.4 79.5 5 0 0 11268 14026
HT20 LGI 1 B S MCS5 5 185 30.7 19.7 57.7 5 8 9 3918 9793
HT20 LGI 1 MCS6 6 164 33.0 0.0 0.0 5 0 0 6 102
HT20 LGI 1 MCS7 7 148 35.1 0.0 0.0 0 0 0 0 44
With the fix:
best ____________rate__________ ____statistics___ _____last____ ______sum-of________
mode guard # rate [name idx airtime max_tp] [avg(tp) avg(prob)] [retry|suc|att] [#success | #attempts]
HT20 LGI 1 S MCS0 0 1477 5.6 1.8 28.6 1 0 0 1 5
HT20 LGI 1 DP MCS1 1 738 10.6 9.7 82.6 4 0 0 14 34
HT20 LGI 1 MCS2 2 492 14.9 9.2 55.4 5 0 0 52 77
HT20 LGI 1 B S MCS3 3 369 18.8 15.6 74.9 5 1 1 417 554
HT20 LGI 1 A MCS4 4 246 25.4 16.7 59.2 5 1 1 13812 17951
HT20 LGI 1 C S MCS5 5 185 30.7 14.0 41.0 5 1 5 57 640
HT20 LGI 1 MCS6 6 164 33.0 0.0 0.0 0 0 1 0 48
HT20 LGI 1 S MCS7 7 148 35.1 0.0 0.0 0 0 0 0 36
We can notice the device try now to send with lower rates (and high
success rates). At the end, we measured 20-25% better throughput with
this patch.
Fixes: 9bca45f3d6 ("staging: wfx: allow to send 802.11 frames")
Tested-by: Olivier Souloumiac <olivier.souloumiac@silabs.com>
Tested-by: Alexandr Suslenko <suslenko.o@ajax.systems>
Reported-by: Alexandr Suslenko <suslenko.o@ajax.systems>
Co-developed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Felipe Negrelli Wolter <felipe.negrelliwolter@silabs.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231004123039.157112-1-jerome.pouiller@silabs.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0731c05c ]
As a matter of fact the regmap_pmu already is mandatory because
it is used unconditionally in the driver. Bail out gracefully in
probe() rather than crashing later.
Link: https://lore.kernel.org/lkml/20230704093242.583575-2-s.hauer@pengutronix.de/
Fixes: b9d1262bca ("PM / devfreq: event: support rockchip dfi controller")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6411959c10 ]
If the "struct can_priv::echoo_skb" is accessed out of bounds, this
would cause a kernel crash. Instead, issue a meaningful warning
message and return with an error.
Fixes: a6e4bc5304 ("can: make the number of echo skb's configurable")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-5-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6841cab8c4 ]
This race condition was discovered while updating the at91_can driver
to use can_bus_off(). The following scenario describes how the
converted at91_can driver would behave.
When a CAN device goes into BUS-OFF state, the driver usually
stops/resets the CAN device and calls can_bus_off().
This function sets the netif carrier to off, and (if configured by
user space) schedules a delayed work that calls can_restart() to
restart the CAN device.
The can_restart() function first checks if the carrier is off and
triggers an error message if the carrier is OK.
Then it calls the driver's do_set_mode() function to restart the
device, then it sets the netif carrier to on. There is a race window
between these two calls.
The at91 CAN controller (observed on the sama5d3, a single core 32 bit
ARM CPU) has a hardware limitation. If the device goes into bus-off
while sending a CAN frame, there is no way to abort the sending of
this frame. After the controller is enabled again, another attempt is
made to send it.
If the bus is still faulty, the device immediately goes back to the
bus-off state. The driver calls can_bus_off(), the netif carrier is
switched off and another can_restart is scheduled. This occurs within
the race window before the original can_restart() handler marks the
netif carrier as OK. This would cause the 2nd can_restart() to be
called with an OK netif carrier, resulting in an error message.
The flow of the 1st can_restart() looks like this:
can_restart()
// bail out if netif_carrier is OK
netif_carrier_ok(dev)
priv->do_set_mode(dev, CAN_MODE_START)
// enable CAN controller
// sama5d3 restarts sending old message
// CAN devices goes into BUS_OFF, triggers IRQ
// IRQ handler start
at91_irq()
at91_irq_err_line()
can_bus_off()
netif_carrier_off()
schedule_delayed_work()
// IRQ handler end
netif_carrier_on()
The 2nd can_restart() will be called with an OK netif carrier and the
error message will be printed.
To close the race window, first set the netif carrier to on, then
restart the controller. In case the restart fails with an error code,
roll back the netif carrier to off.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-2-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe5c9940df ]
During testing, I triggered a can_restart() with the netif carrier
being OK [1]. The BUG_ON, which checks if the carrier is OK, results
in a fatal kernel crash. This is neither helpful for debugging nor for
a production system.
[1] The root cause is a race condition in can_restart() which will be
fixed in the next patch.
Do not crash the kernel, issue an error message instead, and continue
restarting the CAN device anyway.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-1-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77f1ee6fd8 ]
Tx power is fetched from firmware's pdev stats. However, during active
CAC, firmware does not fill the current Tx power and sends the max
initialised value filled during firmware init. If host sends this power
to user space, this is wrong since in certain situations, the Tx power
could be greater than the max allowed by the regulatory. Hence, host
should not be fetching the Tx power during an active CAC.
Fix this issue by returning -EAGAIN error so that user space knows that there's
no valid value available.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: 9a2aa68afe ("wifi: ath11k: add get_txpower mac ops")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230912051857.2284-4-quic_adisi@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cf51f9317 ]
A bulk transfer of the USB may contain many packets. And, the total
number of the packets in the bulk transfer may be more than budget.
Originally, only budget packets would be handled by napi_gro_receive(),
and the other packets would be queued in the driver for next schedule.
This patch would break the loop about getting next bulk transfer, when
the budget is exhausted. That is, only the current bulk transfer would
be handled, and the other bulk transfers would be queued for next
schedule. Besides, the packets which are more than the budget in the
current bulk trasnfer would be still queued in the driver, as the
original method.
In addition, a bulk transfer wouldn't contain more than 400 packets, so
the check of queue length is unnecessary. Therefore, I replace it with
WARN_ON_ONCE().
Fixes: cf74eb5a5b ("eth: r8152: try to use a normal budget")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230926111714.9448-433-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b55b775f03 ]
Add missing sys_nanosleep name for RISC-V, which is used by some tests
(e.g. attach_probe).
Fixes: 08d0ce30e0 ("riscv: Implement syscall wrappers")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/bpf/20231004110905.49024-4-bjorn@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f2692ee43 ]
SYS_PREFIX was missing for a RISC-V, which made a couple of kprobe
tests fail.
Add missing SYS_PREFIX for RISC-V.
Fixes: 08d0ce30e0 ("riscv: Implement syscall wrappers")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/bpf/20231004110905.49024-3-bjorn@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 107e6f6fe6 ]
Following [1], es58x_devlink.c now triggers the following
format-truncation GCC warnings:
drivers/net/can/usb/etas_es58x/es58x_devlink.c: In function ‘es58x_devlink_info_get’:
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:41: warning: ‘%02u’ directive output may be truncated writing between 2 and 3 bytes into a region of size between 1 and 3 [-Wformat-truncation=]
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:30: note: directive argument in the range [0, 255]
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:3: note: ‘snprintf’ output between 9 and 12 bytes into a destination of size 9
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
202 | fw_ver->major, fw_ver->minor, fw_ver->revision);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:41: warning: ‘%02u’ directive output may be truncated writing between 2 and 3 bytes into a region of size between 1 and 3 [-Wformat-truncation=]
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:30: note: directive argument in the range [0, 255]
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:3: note: ‘snprintf’ output between 9 and 12 bytes into a destination of size 9
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
212 | bl_ver->major, bl_ver->minor, bl_ver->revision);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:38: warning: ‘%03u’ directive output may be truncated writing between 3 and 5 bytes into a region of size between 2 and 4 [-Wformat-truncation=]
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:30: note: directive argument in the range [0, 65535]
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:3: note: ‘snprintf’ output between 9 and 13 bytes into a destination of size 9
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
222 | hw_rev->letter, hw_rev->major, hw_rev->minor);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is not an actual bug because the sscanf() parsing makes sure that
the u8 are only two digits long and the u16 only three digits long.
Thus below declaration:
char buf[max(sizeof("xx.xx.xx"), sizeof("axxx/xxx"))];
allocates just what is needed to represent either of the versions.
This warning was known but ignored because, at the time of writing,
-Wformat-truncation was not present in the kernel, not even at W=3 [2].
One way to silence this warning is to check the range of all sub
version numbers are valid: [0, 99] for u8 and range [0, 999] for u16.
The module already has a logic which considers that when all the sub
version numbers are zero, the version number is not set. Note that not
having access to the device specification, this was an arbitrary
decision. This logic can thus be removed in favor of global check that
would cover both cases:
- the version number is not set (parsing failed)
- the version number is not valid (paranoiac check to please gcc)
Before starting to parse the product info string, set the version
sub-numbers to the maximum unsigned integer thus violating the
definitions of struct es58x_sw_version or struct es58x_hw_revision.
Then, rework the es58x_sw_version_is_set() and
es58x_hw_revision_is_set() functions: remove the check that the
sub-numbers are non zero and replace it by a check that they fit in
the expected number of digits. This done, rename the functions to
reflect the change and rewrite the documentation. While doing so, also
add a description of the return value.
Finally, the previous version only checked that
&es58x_hw_revision.letter was not the null character. Replace this
check by an alphanumeric character check to make sure that we never
return a special character or a non-printable one and update the
documentation of struct es58x_hw_revision accordingly.
All those extra checks are paranoid but have the merit to silence the
newly introduced W=1 format-truncation warning [1].
[1] commit 6d4ab2e97d ("extrawarn: enable format and stringop overflow warnings in W=1")
Link: https://git.kernel.org/torvalds/c/6d4ab2e97dcf
[2] https://lore.kernel.org/all/CAMZ6Rq+K+6gbaZ35SOJcR9qQaTJ7KR0jW=XoDKFkobjhj8CHhw@mail.gmail.com/
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/linux-can/20230914-carrousel-wrecker-720a08e173e9-mkl@pengutronix.de/
Fixes: 9f06631c3f ("can: etas_es58x: export product information through devlink_ops::info_get()")
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230924110914.183898-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a341c9b2 ]
Toshiba Portégé R100 has both acpi_video and toshiba_acpi vendor
backlight driver working. But none of them gets activated as it has
a VGA with no kernel driver (Trident CyberBlade XP4m32).
The DMI strings are very generic ("Portable PC") so add a custom
callback function to check for Trident CyberBlade XP4m32 PCI device
before enabling the vendor backlight driver (better than acpi_video
as it has more brightness steps).
Fixes: 5aa9d943e9 ("ACPI: video: Don't enable fallback path for creating ACPI backlight by default")
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 046ece773c ]
In accordance with ACPI specificication and _DSD data buffer
representation the data there is an array of bytes. Hence,
accessing it with something longer will create a sparse data
which is against of how device property APIs work in general
and also not defined in the ACPI specification (see [1]).
Fix the code to emit an error if non-byte accessor is used to
retrieve _DSD buffer data.
Fixes: 369af6bf2c ("ACPI: property: Read buffer properties as integers")
Link: https://uefi.org/specs/ACPI/6.5/19_ASL_Reference.html#buffer-declare-buffer-object # [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ rjw: Add missing braces ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3391ee7f9e ]
In 'rtl92c_dm_check_edca_turbo()', 'rtl88e_dm_check_edca_turbo()',
and 'rtl8723e_dm_check_edca_turbo()', the DL limit should be set
from the corresponding field of 'rtlpriv->btcoexist' rather than
UL. Compile tested only.
Fixes: 0529c6b817 ("rtlwifi: rtl8723ae: Update driver to match 06/28/14 Realtek version")
Fixes: c151aed6aa ("rtlwifi: rtl8188ee: Update driver to match Realtek release of 06282014")
Fixes: beb5bc4020 ("rtlwifi: rtl8192c-common: Convert common dynamic management routines for addition of rtl8192se and rtl8192de")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230928052327.120178-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a135798e6e ]
tcp_init_metrics() only wants to get metrics if they were
previously stored in the cache. Creating an entry is adding
useless costs, especially when tcp_no_metrics_save is set.
Fixes: 51c5d0c4b1 ("tcp: Maintain dynamic metrics in local cache.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 081480014a ]
We need to set tp->snd_ssthresh to TCP_INFINITE_SSTHRESH
in the case tcp_get_metrics() fails for some reason.
Fixes: 9ad7c049f0 ("tcp: RFC2988bis + taking RTT sample from 3WHS for the passive open side")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbc3a15322 ]
When removing an item from RCU protected list, we must prevent
store-tearing, using rcu_assign_pointer() or WRITE_ONCE().
Fixes: 04f721c671 ("tcp_metrics: Rewrite tcp_metrics_flush_all")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79bd60ee87 ]
If an error occurs and channel_detector_exit() is called, it relies on
entries of the 'detectors' array to be NULL.
Otherwise, it may access to un-initialized memory.
Fix it and initialize the memory, as what was done before the commit in
Fixes.
Fixes: a063b650ce ("ath: dfs_pattern_detector: Avoid open coded arithmetic in memory allocation")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/ad8c55b97ee4b330cb053ce2c448123c309cc91c.1695538105.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c558d22e7a ]
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val and
mt76_connac_get_he_phy_cap for the firmware can select the proper rate.
Fixes: 41ac53c899 ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: David Ruth <druth@chromium.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32b1000db2 ]
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val by distinguishing if
it can support chanctx to fix the incorrect rate pickup.
Fixes: 41ac53c899 ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: David Ruth <druth@chromium.org>
Tested-by: David Ruth <druth@chromium.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f502065559 ]
Move struct ieee80211_chanctx_conf up to struct mt76_vif to allow the
connac2 library can access the struct ieee80211_chanctx_conf * member in
struct mt76_vif.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: David Ruth <druth@chromium.org>
Tested-by: David Ruth <druth@chromium.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stable-dep-of: 32b1000db2 ("wifi: mt76: mt7921: fix the wrong rate pickup for the chanctx driver")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ced1a0b8f3 ]
Without this patch, when ap sets the tx stream number to 2,
ap won't send any beamforming packet.
Fixes: f89f297aef ("mt76: mt7915: fix txbf starec TLV issues")
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 413f05d68d ]
When the set_chan_info command is set with CH_SWITCH_NORMAL reason,
even if the action is UNI_CHANNEL_RX_PATH, it'll still generate some
unexpected tones, which might confuse DFS CAC tests that there are some
tone leakages. To get rid of these kinds of false alarms, always bypass
DPD calibration when IEEE80211_CONF_IDLE is set.
Reviewed-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stable-dep-of: c685034cab ("wifi: mt76: fix per-band IEEE80211_CONF_MONITOR flag comparison")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0197923ecf ]
RX vector reports channel bandwidth 320-1 and 320-2 with different
values. Fix it to correctly report rx rate when using CBW320-2.
Fixes: 80f5a31d28 ("wifi: mt76: mt7996: add support for EHT rate report")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e19028104b ]
According to P802.11be_D3.2 Table 9-404m, the minimum value of
Beamformee SS field shall be 3. Fix the values to follow the spec.
Fixes: 348533eb96 ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d40fd59b72 ]
The bf_num field represents how many bands can support beamform, so set
the value to 3, and bf_bitmap represents the bitmap of bf_num.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bde2e77f76 ]
Set correct wcid in txp to let the SDO hw module look into the correct
wtbl, otherwise the tx descriptor may be wrongly fiiled. This patch also
fixed the issue that driver could not correctly report sta statistics,
especially in WDS mode, which misled AQL.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Co-developed-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 832f426997 ]
The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stable-dep-of: bde2e77f76 ("wifi: mt76: mt7996: set correct wcid in txp")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3176205933 ]
Before preparing the new beacon, check the queue status, flush out all
previous beacons and buffered multicast packets, then (if necessary)
try to recover more gracefully from a stuck beacon condition by making a
less invasive attempt at getting the MAC un-stuck.
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c677dda165 ]
Only trigger PSE reset if PSE was stuck, otherwise it can cause DMA issues.
Trigger the PSE reset while DMA is fully stopped in order to improve
reliabilty.
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baa19b2e4b ]
It turns out that the code in mt7603_rx_pse_busy() does not detect actual
hardware hangs, it only checks for busy conditions in PSE.
A reset should only be performed if these conditions are true and if there
is no rx activity as well.
Reset the counter whenever a rx interrupt occurs. In order to also deal with
a fully loaded CPU that leaves interrupts disabled with continuous NAPI
polling, also check for pending rx interrupts in the function itself.
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d74f1da77 ]
Currently EXPORT_*_SIMPLE_DEV_PM_OPS() use EXPORT_*_DEV_PM_OPS() set
of macros to export dev_pm_ops symbol, which export the symbol in case
CONFIG_PM=y but don't take CONFIG_PM_SLEEP into consideration.
Since _SIMPLE_ variants of _PM_OPS() do not include runtime PM handles
and are only used in case CONFIG_PM_SLEEP=y, we should not be exporting
dev_pm_ops symbol for them in case CONFIG_PM_SLEEP=n.
This can be fixed by having two distinct set of export macros for both
_RUNTIME_ and _SIMPLE_ variants of _PM_OPS(), such that the export of
dev_pm_ops symbol used in each variant depends on CONFIG_PM and
CONFIG_PM_SLEEP respectively.
Introduce _DEV_SLEEP_PM_OPS() set of export macros for _SIMPLE_ variants
of _PM_OPS(), which export dev_pm_ops symbol only in case CONFIG_PM_SLEEP=y
and discard it otherwise.
Fixes: 34e1ed189f ("PM: Improve EXPORT_*_DEV_PM_OPS macros")
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 583058542f ]
If we just check "result & RX_DROP_UNUSABLE", this really only works
by accident, because SKB_DROP_REASON_SUBSYS_MAC80211_UNUSABLE got to
have the value 1, and SKB_DROP_REASON_SUBSYS_MAC80211_MONITOR is 2.
Fix this to really check the entire subsys mask for the value, so it
doesn't matter what the subsystem value is.
Fixes: 7f4e09700b ("wifi: mac80211: report all unusable beacon frames")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39564b475a ]
Commit 5b32b6dd96 ("ath11k: Remove core PCI references from
PCI common code") breaks with one MSI vector because it moves
affinity setting after IRQ request, see below log:
[ 1417.278835] ath11k_pci 0000:02:00.0: failed to receive control response completion, polling..
[ 1418.302829] ath11k_pci 0000:02:00.0: Service connect timeout
[ 1418.302833] ath11k_pci 0000:02:00.0: failed to connect to HTT: -110
[ 1418.303669] ath11k_pci 0000:02:00.0: failed to start core: -110
The detail is, if do affinity request after IRQ activated,
which is done in request_irq(), kernel caches that request and
returns success directly. Later when a subsequent MHI interrupt is
fired, kernel will do the real affinity setting work, as a result,
changs the MSI vector. However at that time host has configured
old vector to hardware, so host never receives CE or DP interrupts.
Fix it by setting affinity before registering MHI controller
where host is, for the first time, doing IRQ request.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1
Fixes: 5b32b6dd96 ("ath11k: Remove core PCI references from PCI common code")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230907015606.16297-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
