Some old devices with 4 MiB flashes were using 0x1000 block size and
could use smaller (0x6000 bytes) flash partition for storing NVRAM
content. This adds support for reading NVRAM on Netgear WNR1000 V3.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19005/
Signed-off-by: James Hogan <jhogan@kernel.org>
This adds support for detecting this model board and registers some LEDs
and buttons.
There are two uncommon things regarding this device:
1) It can use two different "board_id" ID values.
Unit I have uses "U12H139T00_NETGEAR" value. This magic is also used
in firmware file header. There are two reports (one from an OpenWrt
user) of a different "U12H139T50_NETGEAR" magic though.
2) Power LEDs share GPIOs with buttons.
Amber one seems to share GPIO 2 with WPS button and green one seems
to share GPIO 3 with reset button. It remains unknown how to support
them and handle buttons at the same time. For that reason they aren't
added to the list of supported LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19004/
Signed-off-by: James Hogan <jhogan@kernel.org>
arch/mips/boot/dts/Makefile collects objects from sub-directories into
built-in.a only when CONFIG_BUILTIN_DTB is enabled. Reflect it also to
the sub-directory Makefiles. This suppresses unneeded built-in.a
creation in arch/mips/boot/dts/*/ directories.
While I am here, I replaced $(patsubst %.dtb, %.dtb.o, $(dtb-y)) with
$(addsuffix .o, $(dtb-y)) to simplify the code a little bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19099/
Signed-off-by: James Hogan <jhogan@kernel.org>
GPL-1.0 is not part of the valid identifier list and as its meaning is GPL
version 1.0 only this would be incompatible with the kernel license.
As this code was included into the kernel, assume its GPL-1.0+
Fixes: 84b2170109 ("ARM: S3C24XX: Add SPDX license identifiers")
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Based on discussion with Kate Stewart this license is not a
BSD-2-Clause, but is now formally identified as Linux-OpenIB
by SPDX.
The key difference between the licenses is in the 'warranty'
paragraph.
if_infiniband.h refers to the 'OpenIB.org' license, but
does not include the text, instead it links to an obsolete
web site that contains a license that matches the BSD-2-Clause
SPX. There is no 'three clause' version of the OpenIB.org
license.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Command 'perf record' calls:
cmd_report()
record__auxtrace_init()
auxtrace_record__init()
On s390 function auxtrace_record__init() returns random return value due
to missing initialization.
This sometime causes 'perf record' to exit immediately without error
message and creating a perf.data file.
Fix this by setting error the return code to zero before returning from
platform specific functions which may not set the error code in call
cases.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180423142940.21143-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The RDMA CM will select a source device and address by consulting
the routing table if no source address is passed into
rdma_resolve_address(). Userspace will ask for this by passing an
all-zero source address in the RESOLVE_IP command. Unfortunately
the new check for non-zero address size rejects this with EINVAL,
which breaks valid userspace applications.
Fix this by explicitly allowing a zero address family for the source.
Fixes: 2975d5de64 ("RDMA/ucma: Check AF family prior resolving address")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Several options were incorrectly described, some lacked describing
required arguments while others were simply not documented, fix it.
Signed-off-by: Sangwon Hong <qpakzk@gmail.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Taeung Song <treeze.taeung@gmail.com>
Link: http://lkml.kernel.org/r/1524382146-19609-1-git-send-email-qpakzk@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Enable the remoteproc framework and the da8xx remoteproc driver by
default in the davinci defconfig.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This is needed by the spi-mem logic to force all messages that have been
queued before a memory operation to be sent before we start the memory
operation. We do that in order to guarantee that spi-mem operations do
not preempt regular SPI transfers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_{map,unmap}_buf() are needed by the spi-mem logic that is about to
be introduced to prepare data buffer for DMA operations.
Remove the static specifier on these functions and add their prototypes
to drivers/spi/internals.h. We do not export the symbols here because
both SPI_MEM and SPI can't be enabled as modules and we'd like to
prevent controller/device drivers from using these functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like axp221, axp223, axp813 the axp803 is also supporting external
regulator to drive the OTG VBus through N_VBUSEN PMIC pin.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
intel_scu_ipc_i2c_cntrl() calls mutex_lock(), which indicates
this function is not called in atomic context.
Despite never getting called from atomic context,
intel_scu_ipc_i2c_cntrl() calls mdelay to busily wait.
This is not necessary and can be replaced with usleep_range to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
.. and other related fields that do not need to be enabled
for events that have sampling leader.
It fixes the perf top usage Ingo reported broken:
# perf top -e '{cycles,msr/aperf/}:S'
The 'msr/aperf/' event is configured for write_back sampling, which is
not allowed by the MSR PMU, so it fails to create the event.
Adjusting related attr test.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180423090823.32309-6-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Roopa Prabhu says:
====================
fib rules extack support
First patch refactors code to move fib rule netlink handling
into a common function. This became obvious when adding
duplicate extack msgs in add and del paths. Second patch
adds extack msgs.
v2 - Dropped the ip route get support and selftests from
the series to look at the input path some more (as pointed
out by ido). Will come back to that next week when i have
some time. resending just the extack part for now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reduces code duplication in the fib rule add and del paths.
Get rid of validate_rulemsg. This became obvious when adding duplicate
extack support in fib newrule/delrule error paths.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent code refactoring made the argument for some helper
functions to be the explicit UAC_CS_* and UAC2_CS_* value instead of
0-based offset. However, there was one place left forgotten, and it
caused a regression on some devices appearing as the inconsistent
mixer setup.
This patch corrects the forgotten conversion.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199449
Fixes: 21e9b3e931 ("ALSA: usb-audio: fix uac control query argument")
Tested-by: Nazar Mokrynskyi <nazar@mokrynskyi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is one place missing __user annotation to the pointer used by
the recent code refactoring. Reported by sparse.
Fixes: 450296f305 ("ALSA: control: code refactoring TLV ioctl handler")
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently all the event parsing fails end up in the event_pmu rule, and
display misleading help like:
$ perf stat -e inst kill
event syntax error: 'inst'
\___ Cannot find PMU `inst'. Missing kernel support?
...
The reason is that the event_pmu is too strong and match also single
string. Changing it to force the '/' separators to be part of the rule,
and getting the proper error now:
$ perf stat -e inst kill
event syntax error: 'inst'
\___ parser error
Run 'perf list' for a list of valid events
...
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180423090823.32309-5-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The 'perf stat' fallback for EACCES error sets the exclude_kernel
perf_event_attr and tries perf_event_open() again with it. In addition,
it also changes the name of the event to reflect that change by adding
the 'u' modifier.
But it does not take into account the '/' separator, so the event name
can end up mangled, like: (note the '/:' characters)
$ perf stat -e cpu/cpu-cycles/ kill
...
386,832 cpu/cpu-cycles/:u
Adding the code to check on the '/' separator and set the following
correct event name:
$ perf stat -e cpu/cpu-cycles/ kill
...
388,548 cpu/cpu-cycles/u
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180423090823.32309-4-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf test case 58 (record+probe_libc_inet_pton.sh) executed on s390x
using kernel 4.16.0rc3 displays this result:
# perf trace --no-syscalls -e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
probe_libc:inet_pton: (3ffa0240448)
__GI___inet_pton (/usr/lib64/libc-2.26.so)
gaih_inet (inlined)
__GI_getaddrinfo (inlined)
main (/usr/bin/ping)
__libc_start_main (/usr/lib64/libc-2.26.so)
_start (/usr/bin/ping)
After I installed kernel 4.16.0 the same tests uses commands:
# perf record -e probe_libc:inet_pton/call-graph=dwarf/
-o /tmp/perf.data.abc ping -6 -c 1 ::1
# perf script -i /tmp/perf.data.abc
and displays:
ping 39048 [006] 84230.381198: probe_libc:inet_pton: (3ffa0240448)
140448 __GI___inet_pton (/usr/lib64/libc-2.26.so)
fbde1 gaih_inet (inlined)
fe2b9 __GI_getaddrinfo (inlined)
398d main (/usr/bin/ping)
Nothing else changed including glibc elfutils and other libraries picked
up by the build.
The entries for __libc_start_main and _start are missing.
I bisected missing __libc_start_main and _start to commit
Fixes: 3d20c62466 ("perf unwind: Unwind with libdw doesn't take symfs into account")
When I undo this commit I get this call stack on s390:
[root@s35lp76 perf]# ./perf script -i /tmp/perf.data.abc
ping 39048 [006] 84230.381198: probe_libc:inet_pton: (3ffa0240448)
140448 __GI___inet_pton (/usr/lib64/libc-2.26.so)
fbde1 gaih_inet (inlined)
fe2b9 __GI_getaddrinfo (inlined)
398d main (/usr/bin/ping)
22fbd __libc_start_main (/usr/lib64/libc-2.26.so)
457b _start (/usr/bin/ping)
Looks like dwarf functions dwfl_xxx create different call back stack
trace when using file /usr/lib/debug/usr/bin/ping-20161105-7.fc27.s390x.debug
instead of file /usr/bin/ping.
Fix this test case on s390 and do not expect any call back stack entry
after the main() function. Also be more robust and accept a leading
__GI_ prefix in front of getaddrinfo.
On x86 this test case shows the same call stack using both kernel
versions 4.16.0rc3 and 4.16.0 and also stops at main:
[root@f27 perf]# ./perf script -i /tmp/perf.data.tmr
ping 4446 [000] 172.027088: probe_libc:inet_pton: (7fdfa08c93c0)
1393c0 __GI___inet_pton (/usr/lib64/libc-2.26.so)
fe60d getaddrinfo (/usr/lib64/libc-2.26.so)
2f40 main (/usr/bin/ping)
[root@f27 perf]#
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Martin Vuille <jpmv27@aim.com>
Link: http://lkml.kernel.org/r/20180423082428.7930-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Make the type field in pmu-events/arch/s390/mapfile.cvs more generic to
match the created cpuid string for s390.
The pattern also checks for the counter first version number and counter
second version number ([13]\.[1-5]) and the authorization field which
follows.
These numbers do not exist in the cpuid identification string when perf
commands are executed on a z/VM environment (which does not support CPU
counter measurement facility).
CPUID string for LPAR:
cpuid : IBM,3906,704,M03,3.5,002f
CPUID string for z/VM:
cpuid : IBM,2964,702,N96
This allows the removal of s390 specific cpuid compare code and uses the
common compare function with its regular expression matching algorithm.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180423081745.3672-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since commit 39cee200c2 ("usb: musb: core: call init and shutdown for
the usb phy") the musb USB phy is initialised by musb_core, but the
original initialisation in the dsps-glue init callback was left in
place resulting in two calls to phy init during probe (and similarly,
two shutdowns on remove).
Drop the duplicate phy init and shutdown calls from the dsps glue in
favour of the ones in musb core, which other glue drivers rely on.
Note however that any generic phy is still initialised in the glue init
callback (just as for the other drivers).
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the new HCD flag which prevents USB core from trying to manage our
phys.
This is needed to be able to associate the controller platform device
with the glue device device-tree node on the BBB which uses legacy USB
phys. Otherwise, the generic phy lookup in usb_phy_roothub_init() and
thus HCD registration fails repeatedly with -EPROBE_DEFER (see commit
178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD
core")).
Note that a related phy-lookup issue was recently worked around in the
phy core by commit b7563e2796 ("phy: work around 'phys' references to
usb-nop-xceiv devices"). Something similar may now be needed for other
USB phys, and in particular if we eventually want to let USB core manage
musb generic phys.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcp_rcv_space_adjust is called every time data is copied to user space,
introducing a tcp tracepoint for which could show us when the packet is
copied to user.
When a tcp packet arrives, tcp_rcv_established() will be called and with
the existed tracepoint tcp_probe we could get the time when this packet
arrives.
Then this packet will be copied to user, and tcp_rcv_space_adjust will
be called and with this new introduced tracepoint we could get the time
when this packet is copied to user.
With these two tracepoints, we could figure out whether the user program
processes this packet immediately or there's latency.
Hence in the printk message, sk_cookie is printed as a key to relate
tcp_rcv_space_adjust with tcp_probe.
Maybe we could export sockfd in this new tracepoint as well, then we
could relate this new tracepoint with epoll/read/recv* tracepoints, and
finally that could show us the whole lifespan of this packet. But we
could also implement that with pid as these functions are executed in
process context.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fe014d4e6b (staging: wilc1000: free memory allocated for general info
message from firmware) introduced a bug by using wrong source address in
kmemdup(). 'conn_info.req_ies' is used for source address in kempdup()
instead of 'hif_drv->usr_conn_req.ies'.
This commit fixes the NULL pointer dereference issue in
host_int_parse_assoc_resp_info() by using the correct source address in
kmemdup().
Fixes: fe014d4e6b (staging: wilc1000: free memory allocated for general info message from firmware)
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add maintainer for the DPAA2 PTP clock driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add driver for the DPAA2 1588 timer module (RTC)
which interfaces to up to an unlimited number of 10/100/1000 or
10G ethernet MACs, providing current time, alarm, and fiper support.
The 1588 IP control block includes these distinctive features.
- External GPIO trigger for time-stamping
- 2 Time-stamp alarms
- 3 FIPER pulse generators
- Phase adjusted output timer clock
Currently this driver only supports basic functions like
settime/gettime/adjtime/adjfreq.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
map_groups__fixup_end() was called to set the end addresses of kernel
and module maps. But now since machine__create_modules() sets the end
address of modules properly, the only remaining piece is the kernel map.
We can set it with adjacent module's address directly instead of calling
map_groups__fixup_end(). If there's no module after the kernel map, the
end address will be ~0ULL.
Since it also changes the start address of the kernel map, it needs to
re-insert the map to the kmaps in order to keep a correct ordering. Kim
reported that it caused problems on ARM64.
Reported-by: Kim Phillips <kim.phillips@arm.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-team@lge.com
Link: http://lkml.kernel.org/r/20180419235915.GA19067@sejong
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Remove unneeded call to dev_set_drvdata(dev, NULL) since the device
will be deallocated in any case.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the mapping of the QBMan cache enabled area from using ioremap_wc()
to devm_memremap(). This allows the __iomem attribute to be removed from
the pointer (which makes sense as accesses treat this as cacheable memory
not IO memory). These changes allow sparse checks to pass.
Also use devm_ioremap() for the cache inhibited area so unmap occurs
automatically when the device is released.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm_TXPowerTrackingCallback_TSSI() is never called in atomic context.
dm_TXPowerTrackingCallback_TSSI() is only called by
dm_txpower_trackingcallback(), which is set a parameter of
INIT_DELAYED_WORK() in rtl8192_init_priv_task().
Despite never getting called from atomic context,
dm_TXPowerTrackingCallback_TSSI() calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtl8192_usb_disconnect() is never called in atomic context.
rtl8192_usb_disconnect() is only set as ".disconnect" in
struct usb_driver.
Despite never getting called from atomic context,
rtl8192_usb_disconnect() calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ieee80211_softmac_init() is never called in atomic context.
The call chains ending up at ieee80211_softmac_init() is:
[1] ieee80211_softmac_init() <- alloc_ieee80211_rsl() <-
rtl8192_usb_probe()
rtl8192_usb_probe() is set as ".probe" in struct usb_driver.
Despite never getting called from atomic context,
ieee80211_softmac_init() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
prism2_wep_init() is never called in atomic context.
prism2_wep_init() is only set as ".init" in
struct ieee80211_crypto_ops.
The call chains ending up at "->init" function are:
[1] ->init() <- ieee80211_wpa_set_encryption() <-
ieee80211_wpa_supplicant_ioctl()
[2] ->init() <- ieee80211_wx_set_encode_ext_rsl() <-
r8192_wx_set_enc_ext()
[3] ->init() <- ieee80211_wx_set_encode_rsl() <-
r8192_wx_set_enc()
ieee80211_wpa_supplicant_ioctl(), r8192_wx_set_enc_ext() and
r8192_wx_set_enc() call mutex_lock(), which indicates these functions
are not called in atomic context.
Despite never getting called from atomic context,
prism2_wep_init() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ieee80211_tkip_init() is never called in atomic context.
ieee80211_tkip_init() is only set as ".init" in
struct ieee80211_crypto_ops.
The call chains ending up at "->init" function are:
[1] ->init() <- ieee80211_wpa_set_encryption() <-
ieee80211_wpa_supplicant_ioctl()
[2] ->init() <- ieee80211_wx_set_encode_ext_rsl() <-
r8192_wx_set_enc_ext()
[3] ->init() <- ieee80211_wx_set_encode_rsl() <-
r8192_wx_set_enc()
ieee80211_wpa_supplicant_ioctl(), r8192_wx_set_enc_ext() and
r8192_wx_set_enc() call mutex_lock(), which indicates these functions
are not called in atomic context.
Despite never getting called from atomic context,
ieee80211_tkip_init() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ieee80211_ccmp_init() is never called in atomic context.
ieee80211_ccmp_init() is only set as ".init" in
struct ieee80211_crypto_ops.
The call chains ending up at "->init" function are:
[1] ->init() <- ieee80211_wpa_set_encryption() <-
ieee80211_wpa_supplicant_ioctl()
[2] ->init() <- ieee80211_wx_set_encode_ext_rsl() <-
r8192_wx_set_enc_ext()
[3] ->init() <- ieee80211_wx_set_encode_rsl() <-
r8192_wx_set_enc()
ieee80211_wpa_supplicant_ioctl(), r8192_wx_set_enc_ext() and
r8192_wx_set_enc() call mutex_lock(), which indicates these functions
are not called in atomic context.
Despite never getting called from atomic context,
ieee80211_ccmp_init() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added blank spaces between a plus sign in order to standardize the coding
style.
Signed-off-by: Joao Dalben <jhdalben@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix most checkpatch.pl issues of type:
CHECK: Alignment should match open parenthesis
Signed-off-by: Gabriel Francisco Mandaji <gfmandaji@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to free the kthreads in error case before leaving
vchiq_init_state() otherwise we leak resources.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all calls of wake_up_process to one point, whichs makes the
following implementation of clean-up code easier.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vchiq_initialise() is used in non-interrupt context, so we can
replace udelay with usleep_range as suggested by timers-howto.txt.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiline dereferences aren't nice to review. So fix this checkpatch
warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's better to use the __func__ macro instead of open-code the function
name. This fixes the following checkpatch warning:
WARNING: Prefer using '"%s...", __func__' to using 'x',
this function's name, in a string
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiding memset behind a macro isn't the best, because it relies on that
the parameter is not a pointer. Luckily all user has been removed, so
we can remove BITSET_ZERO too.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
