When the firmware sends a WCN36XX_HAL_SCAN_IND_DEQUEUED indication,
the request is apparently no longer valid. Attempts to stop the hardware
scan request subsequently will lead to the following error message, and
the hardware is no longer able to communicate with any AP:
[ 57.917186] wcn36xx: ERROR hal_stop_scan_offload response failed err=5
Interpreting this indicator message as scan abortion fixes this.
While at it, add a newline to a debug print.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable sta power save in fw for the targets that
supports idle power save. The idle ps enable command
will be ignored by the firmware which does not support
this feature.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SRRI/DRRI are not mapped in the HW Shadow block and can lead
to un-clocked access if common subsystem in the target is
powered down due to idle mode.
To mitigate this problem SRRI/DRRI can be read from
DDR instead of doing an actual hardware read.
Host allocates non cached memory on ddr and configures
the physical address of this memory to the CE hardware.
The hardware updates the RRI on this particular location.
Read SRRI/DRRI from DDR location instead of
direct target read.
Enable retention restore on ddr using hw params to enable
in specific targets.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 needs shadow register write operation support
for copy engine for regular operation in powersave mode.
Add support for copy engine shadow register write in
datapath tx for WCN3990
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3990 supports shadow register for ce write.
Add a hw param for shadow register support.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default ath10k driver enables the support for HW_CHECKSUM
(NETIF_F_HW_CSUM). Since the TCP/UDP checksum calculation is not enabled
in the wcn3990 firmware the checksum is incorrect in the TCP/UDP packets
and all patckets are dropped. But due note that wcn3990 support in
ath10k is still incomplete so this isn't a critical fix (yet).
Enable hw checksum calculations in wcn3990 hardware by
setting the proper flags in msdu descriptor tso flags.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware message to delete BSS keys expects a BSS index to be passed.
This field is currently hard-coded to 0. Fix this by passing in the index
we received from the firmware when the BSS was configured.
The encryption type in that message also needs to be set to what was used
when the key was set, so the assignment of vif_priv->encrypt_type is now
done after the firmware command was sent. This reportedly fixes the
following error in AP mode:
wcn36xx: ERROR hal_remove_bsskey response failed err=6
Also, AFAIU, when a BSS is deleted, the firmware apparently drops all the
keys associated with it. Trying to remove the key explicitly afterwards
will hence lead to the following message:
wcn36xx: ERROR hal_remove_bsskey response failed err=16
This is now suppressed with an extra check for the BSS index validity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When trying to set wow wakeup patterns it fails with this command:
iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx
The reason is that the wow pattern from upper layer is in 802.3 format
for this case, it need to convert it to 802.11 format. The input
offset parameter is used for 802.3, but the actual offset firmware
need depends on rx_decap_mode, so that it needs to be recalculated.
Pattern of 802.3 packet is not same with 802.11 packet. If the
rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will
receive data packet with 802.11 format from hardware.
Tested with QCA6174 hw3.0 with firmware
WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377.
This has always failed, so it's not a regression with new firmware
releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code extracts the physical address for UE errors and then
hooks it up into memory failure infrastructure. On successful
extraction of physical address it wrongly sets "handled = 1" which
means this UE error has been recovered. Since MCE handler gets return
value as handled = 1, it assumes that error has been recovered and
goes back to same NIP. This causes MCE interrupt again and again in a
loop leading to hard lockup.
Also, initialize phys_addr to ULONG_MAX so that we don't end up
queuing undesired page to hwpoison.
Without this patch we see:
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
...
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
Memory failure: 0x20181a08: recovery action for dirty LRU page: Recovered
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
...
Watchdog CPU:38 Hard LOCKUP
After this patch we see:
Severe Machine check interrupt [Not recovered]
NIP: [00007fffaae585f4] PID: 7168 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffaafe28ac
Physical address: 00002017c0bd0000
find[7168]: unhandled signal 7 at 00007fffaae585f4 nip 00007fffaae585f4 lr 00007fffaae585e0 code 4
Memory failure: 0x2017c0bd: recovery action for dirty LRU page: Recovered
Fixes: 01eaac2b05 ("powerpc/mce: Hookup ierror (instruction) UE errors")
Fixes: ba41e1e1cc ("powerpc/mce: Hookup derror (load/store) UE errors")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ALL-H3-CC has a fixed VDD-CPUX voltage at 1.2V, which is supplied
by a regulator.
Set the CPU's cpu-supply property to the VDD-CPUX regulator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Fix device node ordering]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The VDD-CPUX voltage of ALL-H3-CC H3 ver should be 1.2V, not the 3.3V
currently defined in the device tree.
Fix the voltage in the device tree.
Fixes: 6ca358645d ("ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
aTom Lendacky says:
====================
amd-xgbe: AMD XGBE driver fixes 2018-04-23
This patch series addresses some issues in the AMD XGBE driver.
The following fixes are included in this driver update series:
- Improve KR auto-negotiation and training (2 patches)
- Add pre and post auto-negotiation hooks
- Use the pre and post auto-negotiation hooks to disable CDR tracking
during auto-negotiation page exchange in KR mode
- Check for SFP tranceiver signal support and only use the signal if the
SFP indicates that it is supported
This patch series is based on net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must validate sockaddr_len, otherwise userspace can pass fewer data
than we expect and we end up accessing invalid data.
Fixes: 224cf5ad14 ("ppp: Move the PPP drivers")
Reported-by: syzbot+4f03bdf92fdf9ef5ddab@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check sockaddr_len before dereferencing sp->sa_protocol, to ensure that
it actually points to valid data.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Reported-by: syzbot+a70ac890b23b1bf29f5c@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 192dc405f3 ("selftests: net: add tcp_mmap program")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function dca_common_get_tag is local to the source and does not need to be
in global scope, so make it static.
Cleans up sparse warning:
drivers/dca/dca-core.c:273:4: warning: symbol 'dca_common_get_tag' was
not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NPU has a limited number of address translation shootdown (ATSD)
registers and the GPU has limited bandwidth to process ATSDs. This can
result in contention of ATSD registers leading to soft lockups on some
threads, particularly when invalidating a large address range in
pnv_npu2_mn_invalidate_range().
At some threshold it becomes more efficient to flush the entire GPU
TLB for the given MM context (PID) than individually flushing each
address in the range. This patch will result in ranges greater than
2MB being converted from 32+ ATSDs into a single ATSD which will flush
the TLB for the given PID on each GPU.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a single npu context per set of callback parameters. Callers
should be prevented from overwriting existing callback values so
instead return an error if different parameters are passed.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pnv_npu2_init_context() and pnv_npu2_destroy_context() functions
are used to allocate/free contexts to allow address translation and
shootdown by the NPU on a particular GPU. Context initialisation is
implicitly safe as it is protected by the requirement mmap_sem be held
in write mode, however pnv_npu2_destroy_context() does not require
mmap_sem to be held and it is not safe to call with a concurrent
initialisation for a different GPU.
It was assumed the driver would ensure destruction was not called
concurrently with initialisation. However the driver may be simplified
by allowing concurrent initialisation and destruction for different
GPUs. As npu context creation/destruction is not a performance
critical path and the critical section is not large a single spinlock
is used for simplicity.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Don't do this via custom code, instead now that we have support in the
arch hotplug/hotunplug code, rely on those routines to do the right
thing.
The existing flush doesn't work because it uses ppc64_caches.l1d.size
instead of ppc64_caches.l1d.line_size.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds support for flushing potentially dirty cache lines
when memory is hot-plugged/hot-un-plugged. The support is currently
limited to 64 bit systems.
The bug was exposed when mappings for a device were actually
hot-unplugged and plugged in back later. A similar issue was observed
during the development of memtrace, but memtrace does it's own
flushing of region via a custom routine.
These patches do a flush both on hotplug/unplug to clear any stale
data in the cache w.r.t mappings, there is a small race window where a
clean cache line may be created again just prior to tearing down the
mapping.
The patches were tested by disabling the flush routines in memtrace
and doing I/O on the trace file. The system immediately
checkstops (quite reliablly if prior to the hot-unplug of the memtrace
region, we memset the regions we are about to hot unplug). After these
patches no custom flushing is needed in the memtrace code.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Reza Arbab <arbab@linux.ibm.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current mail address is rejected, last activity (with a different
address) in git-history is from 2012. Remove this.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a spelling error found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove cite "Not sure what this does, but it is absolutely essential".
Extract initialization of trackstick part when touchpad is in passthrough
mode for v3 and v6 protocols into own function. Initialization for v3 is:
setscale11, setscale11, setscale11, nibble 0x9, nibble 0x4. Initialization
for v6 is: setscale11, setscale11, setscale11, setrate 0xC8, setrate 0x14.
Nibbles 0x9 and 0x4 for v3 protocol correspond to setrate 0xC8 and 0x14,
therefore these sequences are same.
When touchpad is in passthrough mode, then OS communicates with trackstick
and this sequence is some magic vendor PS/2 command to put trackstick into
"extended" mode. After that sequence trackstick starts reporting packets in
some vendor 4 bytes format (first byte is always 0xE8).
Next step after configuring trackstick to be in "extended" mode, is to
configure touchpad for v3 protocol to expect that trackstick reports data
in "extended" mode. For v3 protocol this is done by setting bit 1 in
register 0xC2C8 (offset 0x08 from base address 0xC2C0).
When both touchpad and trackstick are not configured for "extended" mode
then touchpad reports trackstick packets in different format, which is not
supported by psmouse/alps driver (yet).
In Cirque documentation GP-AN- 130823 INTERFACING TO GEN4 OVER I2C (PDF)
available at http://www.cirque.com/gen4-dev-resources is Logical Address
0xC2C8 named as PS2AuxControl and Bit Number 1 as ProcessAuxExtendedData
with description: Auxiliary device data is assumed to be extended data when
set.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
John Fastabend says:
====================
While testing sockmap with more programs (besides our test programs)
I found a couple issues.
The attached series fixes an issue where pinned maps were not
working correctly, blocking sockets returned zero, and an error
path that when the sock hit an out of memory case resulted in a
double page_put() while doing ingress redirects.
See individual patches for more details.
v2: Incorporated Daniel's feedback to use map ops for uref put op
which also fixed the build error discovered in v1.
v3: rename map_put_uref to map_release_uref
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In the case where the socket memory boundary is hit the redirect
path returns an ENOMEM error. However, before checking for this
condition the redirect scatterlist buffer is setup with a valid
page and length. This is never unwound so when the buffers are
released latter in the error path we do a put_page() and clear
the scatterlist fields. But, because the initial error happens
before completing the scatterlist buffer we end up with both the
original buffer and the redirect buffer pointing to the same page
resulting in duplicate put_page() calls.
To fix this simply move the initial configuration of the redirect
scatterlist buffer below the sock memory check.
Found this while running TCP_STREAM test with netperf using Cilium.
Fixes: fa246693a1 ("bpf: sockmap, BPF_F_INGRESS flag for BPF_SK_SKB_STREAM_VERDICT")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In the recvmsg handler we need to add a wait event to support the
blocking use cases. Without this we return zero and may confuse
user applications. In the wait event any data received on the
sk either via sk_receive_queue or the psock ingress list will
wake up the sock.
Fixes: fa246693a1 ("bpf: sockmap, BPF_F_INGRESS flag for BPF_SK_SKB_STREAM_VERDICT")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Relying on map_release hook to decrement the reference counts when a
map is removed only works if the map is not being pinned. In the
pinned case the ref is decremented immediately and the BPF programs
released. After this BPF programs may not be in-use which is not
what the user would expect.
This patch moves the release logic into bpf_map_put_uref() and brings
sockmap in-line with how a similar case is handled in prog array maps.
Fixes: 3d9e952697 ("bpf: sockmap, fix leaking maps with attached but not detached progs")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds a reference to the dts of the Raspberry Pi 3 B+
in arm, so don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Per Documentation/bpf/bpf_devel_QA.txt add the -target flag to the
sockmap Makefile. Relevant text quoted here,
Otherwise, you can use bpf target. Additionally, you _must_ use
bpf target when:
- Your program uses data structures with pointer or long / unsigned
long types that interface with BPF helpers or context data
structures. Access into these structures is verified by the BPF
verifier and may result in verification failures if the native
architecture is not aligned with the BPF architecture, e.g. 64-bit.
An example of this is BPF_PROG_TYPE_SK_MSG require '-target bpf'
Fixes: 69e8cc134b ("bpf: sockmap sample program")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
BPF_PROG_TYPE_SK_MSG programs use a 'void *' for both data and the
data_end pointers. Additionally, the verifier ensures that every
accesses into the values is a __u64 read. This correctly maps on
to the BPF 64-bit architecture.
However, to ensure that when building on 32bit architectures that
clang uses correct types the '-target bpf' option _must_ be
specified. To make this clear add a note to the Documentation.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Before [1], When MAC address of the netdevice is changed, default GID is
supposed to get deleted and added back which affects the node and/or port
GUID in below sequence.
netdevice_event()
-> NETDEV_CHANGEADDR
default_del_cmd()
del_netdev_default_ips()
bond_delete_netdev_default_gids()
ib_cache_gid_set_default_gid()
ib_cache_gid_del()
add_cmd()
[..]
However, ib_cache_gid_del() was not getting invoked in non bonding
scenarios because event_ndev and rdma_ndev are same.
Therefore, fix such condition to ignore checking upper device when event
ndev and rdma_dev are same; similar to bond_set_netdev_default_gids().
Which this fix ib_cache_gid_del() is invoked correctly; however
ib_cache_gid_del() doesn't find the default GID for deletion because
find_gid() was given default_gid = false with
GID_ATTR_FIND_MASK_DEFAULT set.
But it was getting overwritten by ib_cache_gid_set_default_gid() later
on as part of add_cmd().
Therefore, mac address change used to work for default GID.
With refactor series [1], this incorrect behavior is detected.
Therefore,
when deleting default GID, set default_gid and set MASK flag.
when deleting IP based GID, clear default_gid and set MASK flag.
[1] https://patchwork.kernel.org/patch/10319151/
Fixes: 238fdf48f2 ("IB/core: Add RoCE table bonding support")
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When IPv6 link local address is removed, if it matches with the default
GID, default GID(s)s gets removed which may not be a desired behavior.
This behavior is introduced by refactor work in Fixes tag.
When IPv6 link address is removed, removing its equivalent RoCEv2 GID
which exactly matches with default RoCEv2 GID, is right thing to do.
However achieving it correctly requires lot more changes, likely in
roce_gid_mgmt.c and core/cache.c. This should be done as independent
patch.
Therefore, this patch preserves behavior of not deleteing default GIDs.
This is done by providing explicit hint to consider default GID property
using mask and default_gid; similar to add_gid().
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Default GIDs are marked reserved at the start of the GID table at index
0 and 1 by gid_table_reserve_default(). Currently when default GID is
requested, it can still allocates an empty slot which was not marked as
RESERVED for default GID, which is incorrect.
At least in current code flow of roce_gid_mgmt.c, in theory we can
still request to allocate more than one/two default GIDs depending
on how upper devices are setup.
Therefore, it is better for cache layer to only allow our reserved slots
to be used by default GID allocation requests.
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Running bpf programs requires disabled preemption,
however at least some* of the BPF_PROG_RUN_ARRAY users
do not follow this rule.
To fix this bug, and also to make it not happen in the future,
let's add explicit preemption disabling/re-enabling
to the __BPF_PROG_RUN_ARRAY code.
* for example:
[ 17.624472] RIP: 0010:__cgroup_bpf_run_filter_sk+0x1c4/0x1d0
...
[ 17.640890] inet6_create+0x3eb/0x520
[ 17.641405] __sock_create+0x242/0x340
[ 17.641939] __sys_socket+0x57/0xe0
[ 17.642370] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 17.642944] SyS_socket+0xa/0x10
[ 17.643357] do_syscall_64+0x79/0x220
[ 17.643879] entry_SYSCALL_64_after_hwframe+0x42/0xb7
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It's called v4l2_fwnode_endpoint_parse, not v4l2_fwnode_parse_endpoint.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Raspberry Pi 3 B+ has a Microchip LAN7515 (connect via USB) and
a Cypress CYW43455 (connect via UART). This patch enables the necessary
drivers.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The Raspberry Pi 3 B+ has a Microchip LAN7515 (connect via USB) and
a Cypress CYW43455 (connect via UART). This patch enables the necessary
drivers.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to gain more test coverage (e.g. Kernel CI) enable
the VCHIQ driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables the necessary driver for Raspberry Pi 3 B+,
which has a LAN7515 chip.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
