When a CRTC is moved to a different transcoder (e.g. on DP-MST stream
allocation), PIPE_SCANLINE and PIPE_FRMCNT can return values latched
from the previous transcoder/mode for up to one vblank period after
the new pipe is enabled. The vblank evasion code in
intel_pipe_update_start()/end() then samples a stale or boundary
scanline and the frame counter ticks during the critical section,
producing diagnostic errors of the form:
[243.348405] xe 0000:00:02.0: [drm] *ERROR* Atomic update failure on
pipe B (start=300 end=301) time 61 us, min 2128, max 2161, scanline
start 1200, end 2165
[248.536260] xe 0000:00:02.0: [drm] *ERROR* Atomic update failure on
pipe B (start=561 end=562) time 61 us, min 2128, max 2161, scanline
start 2162, end 2167
Here "scanline start 1200" is the vblank_start of a previously
programmed mode on a different transcoder, while "2162" is the current
mode's vblank_start sampled before any real frame has been emitted.
Both indicate a stale read rather than a real evasion miss.
Wait for one vblank after crtc_enable() to give the new transcoder a
chance to start producing live PIPE_SCANLINE/FRMCNT values before any
subsequent atomic commit enters the vblank evasion section. This adds
at most one frame of latency on modeset, which is invisible to users.
Reproduced with igt@kms_rotation_crc@sprite-rotation-180 on a DP-MST
sink; with this patch the failures no longer occur.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Pranay Samala <pranay.samala@intel.com>
Link: https://patch.msgid.link/20260429042650.3335718-1-suraj.kandpal@intel.com
For LNL+, odd source size and panning for YUV 422/420 surfaces is
supported. However, it requires the UV (chroma) surface Start X/Y and
width/height to be calculated as ceiling(half of Y plane value) rather
than floor.
The current code uses (>> 17) which combines the U16.16 fixed-point to
integer conversion (>> 16) with a divide-by-2 for chroma subsampling
(>> 1) into a single floor division. For odd Y plane values this
produces an off-by-one error in the UV plane offset.
On Android systems we see PLANE ATS fault when NV12 overlays are
used with odd source dimensions:
[ 126.854200] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:148:pipe A] attached scaler id 0.0 to PLANE:33
[ 126.854617] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:148:pipe A] scaler_user index 0.0: staged scaling request for 1279x719->1340x753
[ 126.854837] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]
[ 126.854926] xe 0000:00:02.0: [drm] *ERROR* [CRTC:148:pipe A] PLANE ATS fault
With Y plane width 1279:
floor(1279/2) = 639 (current)
ceil(1279/2) = 640 (required)
Introduce fp_16_16_div2() and fp_16_16_to_int_ceil() helpers to cleanly
separate the two operations: first halve the U16.16 fixed-point value
for chroma subsampling (staying in fixed-point domain), then convert
to integer with ceiling rounding.
v2: Use DIV_ROUND_UP(value, 1 << 17) to preserve sub-pixel precision
while making the ceiling division readable (Jani, Uma)
v3: Split into two helpers - fp_16_16_div2() for fixed-point division
by 2 and fp_16_16_to_int_ceil() for ceiling conversion to integer,
cleanly separating chroma subsampling from fixed-point to integer
conversion (Jani)
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patch.msgid.link/20260415165849.187693-1-vidya.srinivas@intel.com
Since Xe driver aux ccs enablement dg2 ccs modifiers have been
disabled on i915 driver. Here allow dg2 to use ccs again for framebuffers.
Fixes: 6a99e91a6c ("drm/i915/display: Detect AuxCCS support via display parent interface")
Signed-off-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patch.msgid.link/20260427165715.864721-1-juhapekka.heikkila@gmail.com
Add a helper that determines whether AS SDP can be used for the
current DP configuration. For now this is true only when the sink
supports AS SDP and VRR is enabled, but more conditions may be added
later.
v2:
- Rename to intel_dp_needs_as_sdp(). (Ville)
- Add a #FIXME documenting non-atomic of DP SDP updates. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260424090942.3060291-3-ankit.k.nautiyal@intel.com
Currently we do not support VRR with HDMI so skip vrr compute
config step for all DP branch devices.
v2: Restrict VRR on all DP branch devices instead for checking only for
HDMI. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260424090942.3060291-2-ankit.k.nautiyal@intel.com
Change the drm_err to drm_dbg_kms when we fail to read the FEC
capability. This is mainly because this is called from intel_dp_detect.
Which ends up in race more frequently in case of MST scenarios,
when we are disabling streams but the downstream Dock still sends
signals which causes intel_dp_detect to be invoked which has DPCD
reads. These pass until the Transcoder and DPLL go down causing
AUX to go down too. At this point AUX Timeouts are expected and not
an issue. But this drm_err gets flagged in CI causing noise even
for passing scenarios.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patch.msgid.link/20260423080355.2744117-1-suraj.kandpal@intel.com
There is no need for dereferencing the dmc pointer if the display is
already in the scope of intel_dmc_update_dc6_allowed_count function.
No functional change.
Signed-off-by: Desnes Nunes <desnesn@redhat.com>
Link: https://patch.msgid.link/20260423201020.506908-1-desnesn@redhat.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add intel_ddi_buf_trans_get() wrapper for calling the
encoder->get_buf_trans() hooks, allowing for a centralized place to
e.g. check for VBT overrides for the buf translations.
Cc: Michał Grzelak <michal.grzelak@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20260415115104.1721008-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that we have the pin_params the low level pinning code no
longer needs the entire framebuffer structure. The gem object
alone (along with the pin_params) is enough.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Move the intel_fb_uses_dpt() out from __xe_pin_fb_vma() into
intel_plane_pin_fb() so that we don't do have display stuff
that deep in the pinning code.
And intel_fb_pin_to_ggtt() can just say "this does not need DPT"
always since it's specifically about pinning the fb into GGTT.
The previous logic here was kinda insane with the high level code
assuming GGTT, and low level code potentially deciding otherwise.
In practice it should have been fine because intel_fb_pin_to_ggtt()
only gets used from the initial_plane code, and there we are
not supposed to be have a framebuffer that needs DPT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add a new flag pin_params.needs_fence to inform the pinning
code that the display needs a fence for tiled scanout.
The goal is to eliminate all display specific stuff from
the low level pinning code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Extract the naked DISPLAY_VER<4 checks into a descriptive little
helper (intel_plane_needs_fence()).
And while at it document the reason why the check is what it is.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add a new flag pin_params.needs_physical to inform the pinning
code that the display needs a physical address and not GGTT
address.
This isn't strictly necessary as the current phys_alignment!=0
check is enough in practice. But theoretically one could have
needs_physical==true without any alignment requirements. And
having an explicit flag feels a bit less magical.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add a new flag pin_params.needs_low_address to inform the pinning
code that the display needs a low ggtt address.
The goal is to eliminate all display specific stuff from
the low level pinning code (the direct intel_plane_needs_low_addres())
call in this case).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Extract the naked "gmch? -> need a low ggtt address" check into
a more descriptive helper (intel_plane_needs_low_address()).
The goal being to eliminate all display specific stuff from the
low level pinning code.
The actual implementation still abuses PIN_MAPPABLE to achieve
this goal. I'm not entire convinced that this whole thing even
needs to exist, and the original issue wasn't just caused by
some other bug. But no time to dig into it right now, so let's
keep going.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add a new flag pin_params.neeeds_cpu_lmem_access so that the
low level pinning code doesn't need to peek into the display
driver's framebuffer structure.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Replace the naked "does the framebuffer have a clear color
plane?" checks with a more abstract helper that simply tells
us whether we require CPU access to the framebuffer's memory.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We need to pass a lot of information between the display driver
and the core driver to get framebuffers mapped into GGTT/DPT
correctly. Rather than passing around a swarm of integers and
boolean as function arguments, let's collect it all into a
structure (struct intel_fb_pin_params).
Start by moving the gtt view, alignment, phys_alignment,
and vtd_guard there. Going forward additional things need
to added as well (mainly various boolean flags).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Use the proper gtt view from the plane state rather than always
assuming that it came directly from the FB. This is in the DPT
codepath so the view should currently always come from the FB,
but in the future we may also want per-plane remapping with DPT.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416174448.28264-2-ville.syrjala@linux.intel.com
The display reset only happens from the full reset path. We must
therefore force execlist submission to always take the full reset
path and not the per-engine reset path. Currently the display
reset tests are in fact not testing display resets at all on
platforms using execlist submission. Ring submission and GuC
submission always take the full path anyway.
Also disable the engine reset inside __intel_gt_set_wedged() so
that we simulate the intel_gt_gpu_reset_clobbers_display() behavior
as closely as possible also when taking the full wedge path.
The slight race between the separate intel_display_reset_test()
calls in the overall reset path is harmless. kms_busy will keep
the modparam fixed during the test, and even if someone were to
fiddle with the modparam manually nothing bad should happen if
the calls return different values.
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260415210411.24750-8-ville.syrjala@linux.intel.com
Expose the number of display resets performed in a new
"display_reset_count" debugfs file. kms_busy can use this to
confirm that the kernel actually took the full display reset path.
v2: Give the file an "intel_" namespace (Jani)
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Testcase: igt/kms_busy/*-with-reset
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260415210411.24750-7-ville.syrjala@linux.intel.com
Add static inline stubs for init_clock_gating.h functions
so that we don't need ifdefs in the actual code. We already
have one in intel_display_power.c, and now I need to bring
over intel_display_reset.c.
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260415210411.24750-6-ville.syrjala@linux.intel.com
Only i915 uses the pending_fb_pin counter to potentially whack
the GPU harder if the display gets nuked during a GPU reset.
Move the atomic counter into the i915 specific bits of code, so
that we don't need to worry about on the display side.
For some reason the overlay code kept the pending_fb_pin counter
elevated for longer than just for the pin, but from now on it'll
just cover the actual pinning part.
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260415210411.24750-5-ville.syrjala@linux.intel.com
Stop returning the "is there a display?" status from
intel_display_reset_prepare(). I plan to move the pending_fb_pin
into the i915 code, so I need to make that determination already
before intel_display_reset_prepare() is called. Add a new
intel_display_reset_supported() function for that.
v2: Also check display!=NULL for mock tests
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260415210411.24750-4-ville.syrjala@linux.intel.com
Don't leave a stale xe->display pointer hanging around after
the display driver has been torn down.
While xe shouldn't hit the display reset related issue that
affects i915, leaving stale pointer floating around still
seems like a bad idea.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260415210411.24750-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Don't leave a stale i915->display pointer hanging around after
the display driver has been torn down. Apparently the gt code
calls into the reset codepaths after this, and if the display
pointer is still around we may try to access freed memory.
The whole teardown sequence here seems rather suspect. Why is
display done first and then everything else via the managed
release? Who the heck knows. Someone really needs to dig into
this stuff and figure out the proper init/cleanup sequence for
both i915 (real and mock) and xe...
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260415210411.24750-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Changes have been introduced in Bspec regarding the Tx Swing level,
Tx pre/post coefficients. Update the Tx Swing Level and the Tx
pre/post-cursor co-effecients to incorporate these changes
v2: Updated the commit message (Suraj)
BSpec: 74493
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20260415043952.3189598-1-arun.r.murthy@intel.com
With the fb pinning stuff directly returning the fence_id
there is no longer any need for the vma parent interface.
Get rid of it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260407170942.16515-2-ville.syrjala@linux.intel.com
Get rid of the needlessly complicated PLANE_HAS_FENCE +
intel_parent_vma_fence_id() dance by simply tracking the
fence_id directly in the plane state.
v2: Don't request the redundant fence for fbdev (Jani)
Assign *out_fence_id with '=' instead of '|=' (Sashiko,Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260407170942.16515-1-ville.syrjala@linux.intel.com
When big joiner is enabled, it reserves the adjacent pipe as the
secondary pipe. This happens without the user space knowing, and
subsequent attempts at using the CRTC with that pipe will fail. If the
user space does not have a coping mechanism, i.e. trying another CRTC,
this leads to a black screen.
Try to reduce the impact of the problem on discrete platforms by mapping
the CRTCs to pipes in order A, C, B, and D. If the user space reserves
CRTCs in order, this should trick it to using pipes that are more likely
to be available for and after joining.
Limit this to discrete platforms, which have four pipes, and no eDP, a
combination that should benefit the most with least drawbacks.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260413081609.969342-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reject 90/270 degree rotated BIOS framebuffers in common
code. Currently skl_get_initial_plane_config() already rejects
these, but we may want to implement the missing parts there
so that skl_get_initial_plane_config() could be reused for
general plane state verification purposes.
90/270 degree rotated framebuffers require two completely
separate GGTT mappings (0 degree for the CPU, 270 degree
for the display engine), and the rest of the BIOS FB
takeover code is not prepared for that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Our BIOS FB handling can't deal with DPT, and instead everything
just assumes a direct GGTT mapping. Reject any BIOS FB using DPT.
Most likely this should never happen anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The CPU always needs linear view into the BIOS FB, and for X/Y tiled
buffers that is achieved by the use of a fenced region. If the
underlying driver doesn't support fenced regions then we can't keep
the X/Y tiled BIOS FB. i915 has fenced regions, xe does not.
Probably not a big deal since I don't think we've seen tiled BIOS
FBs outside of some MacBooks. See eg. commit d9a515867b
("drm/i915/gen9+: Fix initial readout for Y tiled framebuffers").
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
There is no such thing as tile4 fenced region, so there is no
way to have a linear view of the tile4 framebuffer for the CPU.
Thus we should never encounter a tile4 BIOS FB, but if we somehow
do, then reject it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
40 msec seems like a very random number for a vblank wait timeout.
Considering ~24Hz display modes are definitely a thing this seems
way too low. Just bump it to a full second to match what we've been
using for normal vblank waits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The initial plane vblank wait operates on display registers,
so it really belongs in the display code proper. Move it there.
We can use intel_parent_irq_enabled() to determine if we can
rely on interrupts or not.
On average we should end up waiting half a frame here, so the
polling interval can be fairly long. 1 ms (which actually
makes poll_timeout_us() use ~250-1000 usec) seems good enough
to me.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
There's no need to use the intel specific struct intel_framebuffer*
type in the initial plane_config structure. Just make it a
struct drm_framebuffer*.
I think the fewer special types we expose in the interface (even
if just pointers) the better. At least then there is no need to
change the interface definition if we ever change the internal
types. And I hope that the existing examples will generally
encourage people to not expose more special types unless
absolutely necessary.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
initial_plane_phys() only needs the 'base' (== ggtt virtual address)
from the plane_config. Stop passing the whole plane_config and just
pass the 'base'.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The 'mem' and 'phy_base' members of struct intel_initial_plane_config
only exist to be passed from initial_plane_phys() to its sole caller.
Just return them via function arguments.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The "plane_config" vs. "plane_configs" naming difference is very
subtle, making it far too easy to use the wrong thing by accident.
Introduce a separate type for the array, making it impossible to
pass in the wrong thing. And while at it name the variable
"all_plane_configs" to help the poor reader make sense of things.
The .config_fini() prototype also mistakenly used the plural
form despite only taking in a singular plane_config. So fix that
one up as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260410150449.9699-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Uninitialized boolean variable may cause unwanted exit from et alignment
loop. Fix this by initializing it as false.
Fixes: 681e12440d ("drm/i915/psr: Repeat Selective Update area alignment")
Cc: <stable@vger.kernel.org> # v6.9+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Nemesa Garg <nemesa.garg@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patch.msgid.link/20260413112345.88853-1-jouni.hogander@intel.com
Currently we take the Hail Mary RGB fallback for "4:2:0 only" modes
already during the first pass when respect_downstream_limits==true.
It seems better to try everything else first (like ignoring TMDS
clock limits) while still preferring 4:2:0, and only if everything
else has failed fall back to RGB.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-10-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Currently we take the Hail Mary RGB fallback for "4:2:0 only" modes
already during the first pass when respect_downstream_limits==true.
It seems better to try everything else first (like ignoring TMDS
clock limits) while still preferring 4:2:0, and only if everything
else has failed fall back to RGB.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-9-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Make sure the sink supports our chosen sink format. I suppose it
might be at least possible that some PCONs might not snoop the EDID
hard enough and filter out all the modes that they should.
Also if we ever want to add a similar "force DVI" knob to DP
outputs that we have for native HDMI, we'd need to manually
get rid of anything DVI sinks can't handle.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-8-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
DVI sinks can't deal with YCbCr. Make sure we have a HDMI sink connected
after the PCON before doing YCbCr 4:2:0 output.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-7-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Currently we only validate "4:2:0 also" modes as RGB. But
if that fails we could perhaps still use the mode in with
4:2:0 output. All we have to do is retry the validation with
the different sink format.
So far we did the double validation only so far as it affects
PCON TMDS clock limits. But validating everything twice seems
a bit more sane.
Note that intel_dp_output_format() might still end up picking
RGB for the actual output format (and letting PCON deal with
the YCbCr conversion). So I suppose we could still fail the
validation due to that, and forcing even the output format
to 4:2:0 might solve it on a third try. But we'd need the
same fallback logic in intel_dp_compute_config(). For now
this seems sufficient.
v2: Pass output_format to intel_dp_mode_min_link_bpp_x16()
Add TODO about remaining issues
Nuke intel_dp_sink_format()
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-6-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
