Mostly cleanups. A few fixes and small features.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQM3A3Pv7vbm9vtjWbacY7uyt+OfQUCaFuvoQAKCRDacY7uyt+O
fQTbAP4oQVGex+lUgoGukD7pFShDGo73aFcKsXMbS+68N0GA1QEAqIrbt27keWJS
23ceOELgJlTEzECj2sMy3LzCp7/EFwc=
=xlnn
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-2025-06-25' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
iwlwifi-next - iwlwifi features
Mostly cleanups. A few fixes and small features.
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'index' variable in the rs_fill_link_cmd() function can reach
LINK_QUAL_MAX_RETRY_NUM during the execution of the inner loop. This
variable is used as an index for the lq_cmd->rs_table array, which has a
size of LINK_QUAL_MAX_RETRY_NUM, without proper validation.
Modify the condition of the inner loop to ensure that the 'index' variable
does not exceed LINK_QUAL_MAX_RETRY_NUM - 1, thereby preventing any
potential overflow issues.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Link: https://patch.msgid.link/20240313101755.269209-1-rand.sec96@gmail.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Add check for the return value of alloc_ordered_workqueue since it may
return NULL pointer.
Fixes: b481de9ca0 ("[IWLWIFI]: add iwlwifi wireless drivers")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://patch.msgid.link/20230110014848.28226-1-jiasheng@iscas.ac.cn
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
When iwl_opmode_register() fails, it does not unregster rate control,
which will cause a memory leak issue, this patch fixes it.
Fixes: 9f66a397c8 ("iwlwifi: mvm: rs: add ops for the new rate scaling in the FW")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Link: https://patch.msgid.link/20221109035213.570-1-xiujianfeng@huawei.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
When reading the interrupt status after a FW reset handshake
timeout, read the actual value not the mask for the non-MSIX
case.
Fixes: ab606dea80 ("wifi: iwlwifi: pcie: add support for the reset handshake in MSI")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.83aafead6061.I2f8571aafa55aa3b936a30b938de9d260592a584@changeid
There is a requirement to exit EMLSR if there wasn't enough throughput
in the secondary link.
This is checked in check_tpt_wk, which runs every 5 seconds in a high
throughput scenario (when the throughput blocker isn't set)
It can happen that this worker is running immediately after we entered
EMLSR, and in that case the secondary link didn't have a chance to have
throughput. In that case we will exit EMLSR for no good reason.
Fix this by tracking the time we entered EMLSR, and in the worker make
sure that 5 seconds passed from when we entered EMLSR. If not, don't
check the secondary link throughput.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.c680f8d7dc37.I8a02d1e8d99df3789da8d5714f19b31a865a61ff@changeid
Move the iwl_trans_pcie_dump_regs() function to utils.c in the PCIe
directory since it operates on PCIe registers and is not
hardware-dependent.
Refactor the pcie_dbg_dumped_once indicator, previously part of the
iwl_trans_pcie struct, into a static variable within the
iwl_trans_pcie_dump_regs() function, where it is used.
Signed-off-by: Rotem Kerem <rotem.kerem@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.06950459ce97.I3105158eb9ae698efebe4b9ada1093aeb1f1b869@changeid
The iwlmld driver is able to handle TTLM changes as long as all TIDs
have the same TID to Link Mapping. Add the corresponding code so that
mac80211 will accept and trigger the TTLM change.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.3b0a4fd2c12b.I1fab7840f1cc222bd1e8cb58ac1a4177474fcd56@changeid
Temporarily block EMLSR when scanning on a P2P Device interface,
as this is an indication that P2P activity is about to start, e.g.,
P2P client connection to a P2P GO.
Since a P2P scan while a station interface connection is active might
be long, increase the EMLSR blocking timeout to 10 seconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.85fb79d537fe.I27523f8d3f00f2b66f5f555f098e323be29465ea@changeid
For the iwlmld driver the RX command is using struct iwl_rx_mpdu_desc
and not the much older struct iwl_rx_mpdu_res_start. Adjust the value of
rx_mpdu_cmd_hdr_size accordingly so that the trace data is correct.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.688d95d99ff3.Id3055ca6c19cf8c821cbbd80c09ca2a21d9acec7@changeid
Since secs_to_jiffies()(commit:b35108a51cf7) has been introduced, we can
use it to avoid scaling the time to msec.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Link: https://patch.msgid.link/20250612022501.3492345-1-liyuesong@vivo.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Doing a scan right after link activation can be less reliable
than at other times, as the firmware is still busy trying to
catch beacons from the just activated link, etc. In case a new
MLO scan request comes in, defer it for a few seconds after a
link activation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.09548e958a9e.I24dbfd425da260f3ae6fa5a48fe25bd4ab6fcf99@changeid
The (applicable) firmware versions will send an error interrupt as
part of the resume process, so there's no need now to check for it
explicitly. Simplify the code. This also fixes an issue where any
dump taken during the resume isn't able to do the reset handshake
as part of the dump (since interrupts are disabled) and then there
isn't all the correct data and we get more errors later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9e778f1bae0c.I96483b5236ab23141b45079464c73f93e0164e65@changeid
Add a debugfs file to be able to control how long, at most,
the device will sleep before waking up the host. This will
be useful to test certain "assert during suspend" scenarios
for the previous change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9f2a39cae1e1.Ie0003f21286fea50b507d0debe06332b030cd4cb@changeid
The D3 handshake can be interrupted by an error, especially
on resume where we no longer want to check explicitly for
errors. Expand the sx_complete to sx_state and handle any
errors occurring during the handshake.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.157dca92c573.I6dd3b9d2f435c2c363224aa84e373931e56a545f@changeid
At load time, the firmware may request a TOP reset via
bit 6 in the IPC status register. Handle that and set
TOP reset in that case. Since the init will be retried,
there's no need to do anything else.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609211928.0875d5f7e066.I62f14008d89416bc4a3a1056e06762561a7fac57@changeid
All ath drivers:
Add "#include <linux/export.h>" to all files that use EXPORT_SYMBOL()
to fix a newly introduced 'make W=1' check. Note that check has
subsequently been changed to only test when W=2, but keep the fixes to
suppress the warning for 'make W=2'.
ath12k:
Properly handle scan requests on multi-radio wiphy devices.
Perform the usual set of bug fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaFq4qwAKCRAsFbugiYzL
e9nKAQC0wQ9QR53BFLGVu3TpR2hbaVaJmYlxCtf+DbrEUbOe1gEAgp2Cz0NdjUaQ
IABFyUquZS/ZAkqytpjXMvoilyDawAg=
=bBFE
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250624' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.17
All ath drivers:
Add "#include <linux/export.h>" to all files that use EXPORT_SYMBOL()
to fix a newly introduced 'make W=1' check. Note that check has
subsequently been changed to only test when W=2, but keep the fixes to
suppress the warning for 'make W=2'.
ath12k:
Properly handle scan requests on multi-radio wiphy devices.
Perform the usual set of bug fixes and cleanups.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
