The Renesas RZ/G3S SoC supports a power saving mode in which power to most
of the SoC components is turned off, including the DMA IP. Add suspend to
RAM support to save and restore the DMA IP registers.
Cyclic DMA channels require special handling. Since they can be paused and
resumed during system suspend/resume, the driver restores additional
registers for these channels during the system resume phase. If a channel
was not explicitly paused during suspend, the driver ensures that it is
paused and resumed as part of the system suspend/resume flow.
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-16-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Protect the driver exposed APIs with runtime PM suspend/resume calls
before accessing HW registers. As the current driver leaves runtime PM
enabled in probe, the purpose of the changes in this patch is to avoid
accessing HW registers after a failed system suspend leaves the runtime
PM state of the device improperly reinitialized.
In that case, the driver remains bound to the device, the APIs are still
exposed, and any access to HW registers without runtime resuming the
device may lead to synchronous aborts.
To avoid leaking resources in case of runtime PM failures, save the error
code returned by PM_RUNTIME_ACQUIRE_ERR() in rz_dmac_terminate_all() and
return it only at the end of the function to allow the cleanup code to
run. A similar approach is used in rz_dmac_free_chan_resources().
Because some exposed APIs (e.g. ->device_terminate_all()) may be called
from atomic context according to the documentation, mark the DMA device as
pm_runtime_irq_safe().
This patch prepares the driver for suspend-to-RAM support.
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-15-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adjust rz_dmac_chan_get_residue() to return error codes on failure and
provide the residue to callers through the residue parameter. This
prepares the code for the addition of runtime PM support.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-14-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add cyclic DMA support to the RZ DMAC driver. A per-channel status bit is
introduced to mark cyclic channels and is set during the DMA prepare
callback. The IRQ handler checks this status bit and calls
vchan_cyclic_callback() accordingly.
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-13-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The CHCTRL_SETEN bit is explicitly set in rz_dmac_enable_hw(). Updating
struct rz_dmac_chan::chctrl with this bit in
rz_dmac_prepare_desc_for_memcpy() and rz_dmac_prepare_descs_for_slave_sg()
is unnecessary in the current code base. Moreover, it conflicts with the
configuration sequence that will be used for cyclic DMA channels during
suspend to RAM. Cyclic DMA support will be introduced in subsequent
commits.
This is a preparatory commit for cyclic DMA suspend to RAM support.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-12-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Subsequent patches will add suspend/resume and cyclic DMA support to the
rz-dmac driver. This support needs to work on SoCs where power to most
components (including DMA) is turned off during system suspend. For this,
some channels (for example cyclic ones) may need to be paused and resumed
manually by the DMA driver during system suspend/resume.
Refactor the pause/resume support so the same code can be reused in the
system suspend/resume path.
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-11-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver used a mix of virt-dma APIs and driver specific logic to
process descriptors. It maintained three internal queues: ld_free,
ld_queue, and ld_active as follows:
- ld_free: stores the descriptors pre-allocated at probe time
- ld_queue: stores descriptors after they are taken from ld_free and
prepared. At the same time, vchan_tx_prep() queues them to
vc->desc_allocated. The vc->desc_allocated list is then checked in
rz_dmac_issue_pending() and rz_dmac_irq_handler_thread() before
starting a new transfer via rz_dmac_xfer_desc(). In turn,
rz_dmac_xfer_desc() grabs the next descriptor from vc->desc_issued and
submits it for transfer
- ld_active: stores the descriptors currently being transferred
The interrupt handler moved a completed descriptor to ld_free before
invoking its completion callback. Once returned to ld_free, the
descriptor can be reused to prepare a new transfer. In theory, this
means the descriptor could be re-prepared before its completion
callback is called.
Commit fully back the driver by the virt-dma APIs. With this, only ld_free
need to be kept to track how many free descriptors are available. This
is now done as follows:
- the prepare stage removes the first descriptor from the ld_free and
prepares it
- the completion calls for it vc->desc_free() (rz_dmac_virt_desc_free())
which re-adds the descriptor at the end of ld_free
With this, the critical areas in prepare callbacks were minimized to only
getting the descriptor from the ld_free list.
Introduce struct rz_dmac_chan::desc to keep track of the currently
transferred descriptor. It is cleared in rz_dmac_terminate_all(),
referenced from rz_dmac_issue_pending() to determine whether a new transfer
can be started, and from rz_dmac_irq_handler_thread() once a descriptor has
completed. Finally, the rz_dmac_device_synchronize() was updated with
vchan_synchronize() call to ensure the terminated descriptor is freed and
the tasklet is killed.
With this, residue computation is also simplified, as it can now be
handled entirely through the virt-dma APIs.
The spin_lock/unlock operations from rz_dmac_irq_handler_thread() were
replaced by guard as the final code after rework is simpler this way.
As subsequent commits will set the Link End bit on the last descriptor
of a transfer, rz_dmac_enable_hw() is also adjusted as part of the full
conversion to virt-dma APIs. It no longer checks the channel enable
status itself; instead, its callers verify whether the channel is
enabled and whether the previous transfer has completed before starting
a new one.
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-10-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the rz_dmac_chan_is_paused() helper to check if the channel is paused.
This helper will be reused in subsequent patches.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-9-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the rz_dmac_chan_is_enabled() helper to check if a channel is
enabled. This helper will be reused in subsequent patches.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-8-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Save the start LM descriptor to avoid starting from the beginning of the
channel's LM descriptor list in rz_dmac_calculate_residue_bytes_in_vd().
This avoids unnecessary iterations.
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-7-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a the rz_dmac_lmdesc_addr() helper function to compute the lmdesc
address, to make the code easier to understand. The helper will be used in
subsequent patches.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-6-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use rz_dmac_disable_hw() instead of open coding it. This unifies the
code and prepares it for the addition of suspend to RAM and cyclic DMA.
The rz_dmac_disable_hw() from rz_dmac_chan_probe() was moved after
vchan_init() as it initializes the channel->vc.chan.device used in
rz_dmac_disable_hw().
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-5-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use list_first_entry_or_null() instead of open-coding it with a
list_empty() check and list_first_entry(). This simplifies the code.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-4-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
list_first_entry() does not return NULL when the list is empty,
making the existing NULL check invalid. Use list_first_entry_or_null()
instead.
Fixes: 21323b118c ("dmaengine: sh: rz-dmac: Add device_tx_status() callback")
Cc: stable@vger.kernel.org
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-3-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Once the interrupt is requested, the interrupt handler may run immediately.
Since the IRQ handler can access channel->ch_base, which is initialized
only after requesting the IRQ, this may lead to invalid memory access.
Likewise, the IRQ thread may access uninitialized data (the ld_free,
ld_queue, and ld_active lists), which may also lead to issues.
Request the interrupts only after everything is set up. To keep the error
path simpler, use dmam_alloc_coherent() instead of dma_alloc_coherent().
Fixes: 5000d37042 ("dmaengine: sh: Add DMAC driver for RZ/G2L SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-2-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add compatible and chip data to support GPCDMA in Tegra264, which has
differences in register layout and address bits compared to previous
versions.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-10-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use 'iommu-map', when provided, to get the stream ID to be programmed
for each channel. Iterate over the channels registered and configure
each channel device separately using of_dma_configure_id() to allow
it to use a separate IOMMU domain for the transfer. However, do this
in a second loop since the first loop populates the DMA device channels
list and async_device_register() registers the channels. Both are
prerequisites for using the channel device in the next loop.
Channels will continue to use the same global stream ID if the
'iommu-map' property is not present in the device tree.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-9-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Switch to managed registration in probe. This simplifies the error
paths in the probe and also removes the requirement of the driver
remove function.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Suggested-by: Frank Li <frank.li@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-8-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tegra264 supports address width of 41 bits. Unlike older SoCs which use
a common high_addr register for upper address bits, Tegra264 has separate
src_high and dst_high registers to accommodate this wider address space.
Add an addr_bits property to the device data structure to specify the
number of address bits supported on each device and use that to program
the appropriate registers.
Update the sg_req struct to remove the high_addr field and use
dma_addr_t for src and dst to store the complete addresses. Extract
the high address bits only when programming the registers.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-7-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Repurpose the struct tegra_dma_channel_regs to define offsets for all the
channel registers. Previously, the struct only held the register values
for each transfer and was wrapped within tegra_dma_sg_req. Move the
values directly into tegra_dma_sg_req and use channel_regs for
storing the register offsets. Update all register reads/writes to use
the struct channel_regs. This prepares for the register offset change
in Tegra264.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-6-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On Tegra264, reset is not available for the driver to control as
this is handled by the boot firmware. Hence make the reset control
optional and update the error message to reflect the correct error.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-5-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add iommu-map property to specify separate stream IDs for each DMA
channel. This enables each channel to be in its own IOMMU domain,
keeping memory isolated from other devices sharing the same DMA
controller.
Define the constraints such that if the channel and stream IDs are
contiguous, a single entry can map all the channels, but if the
channels or stream IDs are non-contiguous support multiple entries.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-4-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On Tegra264, GPCDMA reset control is not exposed to Linux and is handled
by the boot firmware.
Although reset was not exposed in Tegra234 as well, the firmware supported
a dummy reset which just returns success on reset without doing an actual
reset. This is also not supported in Tegra264 BPMP. Therefore mark 'reset'
and 'reset-names' properties as required only for devices prior to
Tegra264.
This also necessitates that the Tegra264 compatible be standalone and
cannot have the fallback compatible of Tegra186. Since there is no
functional impact, we keep reset as required for Tegra234 to avoid
breaking the ABI.
Fixes: bb8c97571d ("dt-bindings: dma: Add Tegra264 compatible string")
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-2-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are multi spba-busses for i.MX8M* platforms, if only search for
the first spba-bus in DT, the found spba-bus may not the real bus of
audio devices, which cause issue for sdma p2p case, as the sdma p2p
script presently does not deal with the transactions involving two devices
connected to the AIPS bus.
Search the SDMA parent node first, which should be the AIPS bus, then
search the child node whose compatible string is spba-bus under that AIPS
bus for the above multi spba-busses case.
Fixes: 8391ecf465 ("dmaengine: imx-sdma: Add device to device support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260407032755.2758049-1-shengjiu.wang@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
By convention MODULE_DEVICE_TABLE() immediately follows the ID table it
exports, because this is easier to read and verify. It also makes more
sense since #ifdef for ACPI or OF could hide both of them.
Most of the drivers already have this correctly placed, so adjust
the missing ones. No functional impact.
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260514060525.9253-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the GPI DMA engine found on the Eliza SoC.
It is fully compatible with the GPI DMA engine found on SM6350,
thus using qcom,sm6350-gpi-dma as fallback compatible.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Pankaj Patil <pankaj.patil@oss.qualcomm.com>
Link: https://patch.msgid.link/20260515-eliza-gpi-dma-v2-1-1255b43d5ca9@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SpacemiT K3 reuses most of the PDMA IP design found on K1, with one
difference being the extended DRCMR base address. Add "spacemit,k3-pdma"
compatible string and define a new mmp_pdma_ops for K3 PDMA.
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260518-k3-pdma-v6-3-67fdf319a8f8@linux.spacemit.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Refactor the DRCMR macro into a helper function mmp_pdma_get_drcmr()
to support variable extended DRCMR base addresses across different PDMA
implementations, such as SpacemiT K3.
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260518-k3-pdma-v6-2-67fdf319a8f8@linux.spacemit.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the "spacemit,k3-pdma" compatible string for the SpacemiT K3 SoC.
While the K3 PDMA IP reuses most of the design found on the earlier
K1 SoC, a new compatible string is required because the DRCMR
(DMA Request/Command Register) base address for extended DMA request
numbers (>= 64) differs from the K1 implementation.
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260518-k3-pdma-v6-1-67fdf319a8f8@linux.spacemit.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Hawi GPI DMA engine follows the same programming model and
register interface as previous generation of Qualcomm SoCs like
kaanapali, glymur, and is fully compatible with earlier GPI DMA
implementations.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Xueyao An <xueyao.an@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260401124028.589931-1-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document compatible string for bam v2.0.0 version found on kaanapali.
BAM v2.0.0 differs from the earlier v1.7.X revision in terms of register
layout and offsets, requiring a distinct compatible for correct hardware
description.
Also add a new example for BAM v2.0.0 to illustrate a more complete
configuration than the existing v1.4 example. The new example covers
64-bit address and size cells, IOMMU bindings and execution
environment–related properties required on newer platforms.
Signed-off-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260514-knp_qce-v2-1-890e3372eef8@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Raspberry Pi 3B by marking the VEC clk critical so it doesn't get
turned off and hang the bus.
-----BEGIN PGP SIGNATURE-----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=JtUn
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the merge window to avoid a boot hang on
Raspberry Pi 3B by marking the VEC clk critical so that it
doesn't get turned off and hang the bus"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: bcm: rpi: Mark VEC clock as CLK_IGNORE_UNUSED
- Drop class_create() for the "tsm" class
-----BEGIN PGP SIGNATURE-----
iIYEABYKAC4WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCae40aBAcZGpid0BrZXJu
ZWwub3JnAAoJEN+KhhkeUWxn/F0BAIpdhnq3TbPMC6Pj0q3DfcXpP+LPD0pqqIom
TwsQVZJCAP4rYVEbIbgeXvkilr7Fpcs2AXbidR/ggBsR3lyVBSNhAA==
=ZK/r
-----END PGP SIGNATURE-----
Merge tag 'tsm-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm
Pull PCIe TSP update from Dan Williams:
"A small update for the TSM core. It is arguably a fix and coming in
late as I have been offline the past few weeks:
- Drop class_create() for the 'tsm' class"
* tag 'tsm-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm:
virt: coco: change tsm_class to a const struct
- kbuild: builddeb - avoid recompiles for non-cross-compiles
Avoid triggering complete rebuilds for non-cross-compile Debian
package builds by only triggering the rebuild of host tools for
actual cross-compile builds.
- kbuild: Never respect CONFIG_WERROR / W=e to fixdep
Avoid spurious rebuilds of fixdep w/ and w/o -Werror during a single
kbuild invocation by never respecting CONFIG_WERROR for fixdep.
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Mathias Krause <minipli@grsecurity.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Thomas Weißschuh <linux@weissschuh.net>
-----BEGIN PGP SIGNATURE-----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=yCeR
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nicolas Schier:
- builddeb - avoid recompiles for non-cross-compiles
Avoid triggering complete rebuilds for non-cross-compile Debian
package builds by only triggering the rebuild of host tools for
actual cross-compile builds
- Never respect CONFIG_WERROR / W=e to fixdep
Avoid spurious rebuilds of fixdep w/ and w/o -Werror during a single
kbuild invocation by never respecting CONFIG_WERROR for fixdep
* tag 'kbuild-fixes-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Never respect CONFIG_WERROR / W=e to fixdep
kbuild: builddeb - avoid recompiles for non-cross-compiles
Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode
-----BEGIN PGP SIGNATURE-----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=mY/t
-----END PGP SIGNATURE-----
Merge tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode"
* tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: abx80x: Disable alarm feature if no interrupt attached
rtc: ntxec: fix OF node reference imbalance
rtc: pic32: allow driver to be compiled with COMPILE_TEST
rtc: ti-k3: Add support to resume from IO DDR low power mode
rtc: cmos: Use platform_get_irq_optional() in cmos_platform_probe()
dt-bindings: rtc: add olpc,xo1-rtc to trivial-rtc
dt-bindings: rtc: sc2731: Add compatible for SC2730
rtc: add data_race() in rtc_dev_poll()
rtc: armada38x: zalloc + calloc to single allocation
dt-bindings: rtc: isl12026: convert to YAML schema
dt-bindings: rtc: microcrystal,rv3028: Allow to specify vdd-supply
rtc: max77686: convert to i2c_new_ancillary_device
dt-bindings: rtc: mpfs-rtc: permit resets
rtc: rx8025: Remove use of i2c_match_id()
rtc: rv8803: Remove use of i2c_match_id()
rtc: rs5c372: Remove use of i2c_match_id()
rtc: pcf2127: Remove use of i2c_match_id()
rtc: m41t80: Remove use of i2c_match_id()
rtc: abx80x: Remove use of i2c_match_id()
mentioning separately: Rafael's commit converting tpm_crb from ACPI driver
to a platform driver. Starting from this release cycle, the branch with TPM
changes mirrored to next is 'for-next-tpm', and patches for keys have their
own separate 'for-next-keys' branch.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRE6pSOnaBC00OEHEIaerohdGur0gUCaezVbgAKCRAaerohdGur
0ggHAQDmhaZ2C3ddAV1WjfXh1YqdWAmqEqoP7ZHAh4OrjyRPTQD+Pc4xl9TSOgHx
/9WzzV6AM6fL5RuC2/PO5RvOKF9mswc=
=tpJM
-----END PGP SIGNATURE-----
Merge tag 'for-next-tpm-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
"Here are the accumulated fixes for 7.1-rc1 and a single structural
change worth mentioning separately: Rafael's commit converting tpm_crb
from ACPI driver to a platform driver"
* tag 'for-next-tpm-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: tpm_tis: stop transmit if retries are exhausted
tpm: tpm_tis: add error logging for data transfer
tpm: avoid -Wunused-but-set-variable
tpm: Use kfree_sensitive() to free auth session in tpm_dev_release()
tpm2-sessions: Fix missing tpm_buf_destroy() in tpm2_read_public()
tpm: Fix auth session leak in tpm2_get_random() error path
tpm: i2c: atmel: fix block comment formatting
tpm_crb: Convert ACPI driver to a platform one
tpm: Make tcpci_pm_ops variable static const
Since v2025.11.22:
Initial SoC Slider support
SoC Slider is an SoC-wide power/performance policy setting.
On SoC Slider systems, EPP plays a diminished role.
Whitespace cleanup via: indent -npro -kr -i8 -ts8 -sob -l160 -ss -ncs -cp1
No functional changes
Signed-off-by: Len Brown <len.brown@intel.com>
x86_energy_perf_policy accesses the SoC Slider via standard
user/kernel APIs to the processor_thermal_soc_slider driver.
Machines that support SoC Slider largely use it instead of EPP,
which may continue to exist in a diminished role, or vanish entirely.
Signed-off-by: Len Brown <len.brown@intel.com>
When processor_thermal_soc_slider is loaded, its slider
and offset modparams are visible. Check that the driver
actually registered the profile named "SoC Slider" before
reading or writing these modparams.
n.b. This utility allows writing the Slider and Offset modparams
even if the driver policy is not "balanced". Currently the
processor_thermal_soc_slider consults those modparams
only in "balanced" mode.
Signed-off-by: Len Brown <len.brown@intel.com>
On Raspberry Pi 3B, the VEC clock is used by the VideoCore firmware
display driver, which remains active until the vc4 driver loads and
sends NOTIFY_DISPLAY_DONE. If this clock is disabled during boot, a bus
lockup happens and the firmware becomes unresponsive, causing a complete
system lockup.
Mark the VEC clock with CLK_IGNORE_UNUSED so it survives the unused
clock disablement and remains available until the vc4 driver takes over
display management.
Fixes: 672299736a ("clk: bcm: rpi: Manage clock rate in prepare/unprepare callbacks")
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/r/5f0bec08-f458-4fba-8bf3-06817a100c4c@sirena.org.uk
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patch.msgid.link/20260401111416.562279-2-mcanal@igalia.com
Tested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Brian Masney <bmasney@redhat.com> # Active contributor to clk
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Several development updates for 7.1-rc1:
- fix a race condition handling PG_dcache_clean
- further cleanups for the fault handling, allowing RT to be enabled
- fixing nzones validation in adfs filesystem driver
- fix for module unwinding
-----BEGIN PGP SIGNATURE-----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=arB6
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux
Pull ARM updates from Russell King:
- fix a race condition handling PG_dcache_clean
- further cleanups for the fault handling, allowing RT to be enabled
- fixing nzones validation in adfs filesystem driver
- fix for module unwinding
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux:
ARM: 9463/1: Allow to enable RT
ARM: 9472/1: fix race condition on PG_dcache_clean in __sync_icache_dcache()
ARM: 9471/1: module: fix unwind section relocation out of range error
fs/adfs: validate nzones in adfs_validate_bblk()
ARM: provide individual is_translation_fault() and is_permission_fault()
ARM: move FSR fault status definitions before fsr_fs()
ARM: use BIT() and GENMASK() for fault status register fields
ARM: move is_permission_fault() and is_translation_fault() to fault.h
ARM: move vmalloc() lazy-page table population
ARM: ensure interrupts are enabled in __do_user_fault()
- Fix accounting of persistent ring buffer rewind
On boot up, the head page is moved back to the earliest point of
the saved ring buffer. This is because the ring buffer being read by
user space on a crash may not save the part it read. Rewinding the head
page back to the earliest saved position helps keep those events from
being lost.
The number of events is also read during boot up and displayed in the
stats file in the tracefs directory. It's also used for other accounting
as well. On boot up, the "reader page" is accounted for but a rewind may
put it back into the buffer and then the reader page may be accounted
for again.
Save off the original reader page and skip accounting it when scanning
the pages in the ring buffer.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCaevLRxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qsNBAQCO9T+3kbDLD/DxRBYjeMXhTg2iY2OV
SHV9jEzcYTahmwEAqVCFY9sNxVYXait/C924SmHCSi1N0HrIuEzIEd29iwk=
=bv+t
-----END PGP SIGNATURE-----
Merge tag 'trace-ring-buffer-v7.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull ring-buffer fix from Steven Rostedt:
- Fix accounting of persistent ring buffer rewind
On boot up, the head page is moved back to the earliest point of the
saved ring buffer. This is because the ring buffer being read by user
space on a crash may not save the part it read. Rewinding the head
page back to the earliest saved position helps keep those events from
being lost.
The number of events is also read during boot up and displayed in the
stats file in the tracefs directory. It's also used for other
accounting as well. On boot up, the "reader page" is accounted for
but a rewind may put it back into the buffer and then the reader page
may be accounted for again.
Save off the original reader page and skip accounting it when
scanning the pages in the ring buffer.
* tag 'trace-ring-buffer-v7.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ring-buffer: Do not double count the reader_page
-----BEGIN PGP SIGNATURE-----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=0AP+
-----END PGP SIGNATURE-----
Merge tag 'block-7.1-20260424' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block fixes from Jens Axboe:
- Series for zloop, fixing a variety of issues
- t10-pi code cleanup
- Fix for a merge window regression with the bio memory allocation mask
- Fix for a merge window regression in ublk, caused by an issue with
the maple tree iteration code at teardown
- ublk self tests additions
- Zoned device pgmap fixes
- Various little cleanups and fixes
* tag 'block-7.1-20260424' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux: (21 commits)
Revert "floppy: fix reference leak on platform_device_register() failure"
ublk: avoid unpinning pages under maple tree spinlock
ublk: refactor common helper ublk_shmem_remove_ranges()
ublk: fix maple tree lockdep warning in ublk_buf_cleanup
selftests: ublk: add ublk auto integrity test
selftests: ublk: enable test_integrity_02.sh on fio 3.42
selftests: ublk: remove unused argument to _cleanup
block: only restrict bio allocation gfp mask asked to block
block/blk-throttle: Add WQ_PERCPU to alloc_workqueue users
block: Add WQ_PERCPU to alloc_workqueue users
block: relax pgmap check in bio_add_page for compatible zone device pages
block: add pgmap check to biovec_phys_mergeable
floppy: fix reference leak on platform_device_register() failure
ublk: use unchecked copy helpers for bio page data
t10-pi: reduce ref tag code duplication
zloop: remove irq-safe locking
zloop: factor out zloop_mark_{full,empty} helpers
zloop: set RQF_QUIET when completing requests on deleted devices
zloop: improve the unaligned write pointer warning
zloop: use vfs_truncate
...
-----BEGIN PGP SIGNATURE-----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=YZdX
-----END PGP SIGNATURE-----
Merge tag 'io_uring-7.1-20260424' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull io_uring fixes from Jens Axboe:
- Fix for a NOMMU bug with io_uring, where NOMMU doesn't grab page refs
at mmap time. NOMMU also has entirely broken FOLL_PIN support, yet
here we are
- A few fixes covering minor issues introduced in this merge window
- data race annotation to shut up KCSAN for when io-wq limits are
applied
- A nospec addition for direct descriptor file updating. Rest of the
direct descriptor path already had this, but for some reason the
update did not. Now they are all the same
- Various minor defensive changes that claude identified and suggested
terrible fixes for, turned into actually useful cleanups:
- Use kvfree() for the imu cache. These can come from kmalloc or
vmalloc depending on size, but the in-cache ones are capped
where it's always kmalloc based. Change to kvfree() in the
cleanup path, making future changes unlikely to mess that up
- Negative kbuf consumption lengths. Can't happen right now, but
cqe->res is used directly, which if other codes changes could
then be an error value
- Fix for an issue with the futex code, where partial wakes on a
vectored fuxes would potentially wake the same futex twice, rather
than move on to the next one. This could confuse an application as it
would've expected the next futex to have been woken
- Fix for a bug with ring resizing, where SQEs or CQEs might not have
been copied correctly if large SQEs or CQEs are used in the ring.
Application side issue, where SQEs or CQEs might have been lost
during resize
- Fix for a bug where EPOLL_URING_WAKE might have been lost, causing a
multishot poll to not be terminated when it's nested, like it should
have been
- Fix for an issue with signed comparison of poll references for the
slow path
- Fix for a user struct UAF in the zcrx code
- Two minor zcrx cleanups
* tag 'io_uring-7.1-20260424' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring: take page references for NOMMU pbuf_ring mmaps
io_uring/poll: ensure EPOLL_ONESHOT is propagated for EPOLL_URING_WAKE
io_uring/zcrx: warn on freelist violations
io_uring/zcrx: clear RQ headers on init
io_uring/zcrx: fix user_struct uaf
io_uring/register: fix ring resizing with mixed/large SQEs/CQEs
io_uring/futex: ensure partial wakes are appropriately dequeued
io_uring/rw: add defensive hardening for negative kbuf lengths
io_uring/rsrc: use kvfree() for the imu cache
io_uring/rsrc: unify nospec indexing for direct descriptors
io_uring: fix spurious fput in registered ring path
io_uring: fix iowq_limits data race in tctx node addition
io_uring/tctx: mark io_wq as exiting before error path teardown
io_uring/tctx: check for setup tctx->io_wq before teardown
io_uring/poll: fix signed comparison in io_poll_get_ownership()
Highlights include:
Bugfixes:
- NFS: Fix handling of ENOSPC so that if we have to resend writes, they
are written synchronously.
- SUNRPC: RDMA transport fixes from Chuck
- NFSv4.2: Several fixes for delegated timestamps
- NFSv4: Failure to obtain a directory delegation should not cause
stat() to fail.
- NFSv4: Rename was failing to update timestamps when a directory
delegation is held.
- NFSv4: Ensure we check rsize/wsize after crossing a NFSv4 filesystem
boundary.
- NFSv4/pnfs: If the server is down, retry the layout returns on reboot
- NFSv4/pnfs: Fallback to MDS could result in a short write being
incorrectly logged.
Cleanups:
- NFS: use memcpy_and_pad in decode_fh
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR8xgHcVzJNfOYElJo6EXfx2a6V0QUCaevSUgAKCRA6EXfx2a6V
0ewIAQD+23uMo5sxY10btKATcBBxswY5YMtN1qQBMyn88N0XfwEAz0+zoEbRv4L2
39goJ/WeJ0/gqhfJV9F+Oe2U1DbsEgM=
=l9y/
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-7.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Bugfixes:
- Fix handling of ENOSPC so that if we have to resend writes, they
are written synchronously
- SUNRPC RDMA transport fixes from Chuck
- Several fixes for delegated timestamps in NFSv4.2
- Failure to obtain a directory delegation should not cause stat() to
fail with NFSv4
- Rename was failing to update timestamps when a directory delegation
is held on NFSv4
- Ensure we check rsize/wsize after crossing a NFSv4 filesystem
boundary
- NFSv4/pnfs:
- If the server is down, retry the layout returns on reboot
- Fallback to MDS could result in a short write being incorrectly
logged
Cleanups:
- Use memcpy_and_pad in decode_fh"
* tag 'nfs-for-7.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (21 commits)
NFS: Fix RCU dereference of cl_xprt in nfs_compare_super_address
NFS: remove redundant __private attribute from nfs_page_class
NFSv4.2: fix CLONE/COPY attrs in presence of delegated attributes
NFS: fix writeback in presence of errors
nfs: use memcpy_and_pad in decode_fh
NFSv4.1: Apply session size limits on clone path
NFSv4: retry GETATTR if GET_DIR_DELEGATION failed
NFS: fix RENAME attr in presence of directory delegations
pnfs/flexfiles: validate ds_versions_cnt is non-zero
NFS/blocklayout: print each device used for SCSI layouts
xprtrdma: Post receive buffers after RPC completion
xprtrdma: Scale receive batch size with credit window
xprtrdma: Replace rpcrdma_mr_seg with xdr_buf cursor
xprtrdma: Decouple frwr_wp_create from frwr_map
xprtrdma: Close lost-wakeup race in xprt_rdma_alloc_slot
xprtrdma: Avoid 250 ms delay on backlog wakeup
xprtrdma: Close sendctx get/put race that can block a transport
nfs: update inode ctime after removexattr operation
nfs: fix utimensat() for atime with delegated timestamps
NFS: improve "Server wrote zero bytes" error
...
