The size limit of H2C commands is 2048. With regulatory that enables
U-NII-6 ~ UNII-8 channels, channel list length combining with channel info
length will exceed that. Split the channel list to parts and do scan
multiple times to workaround that.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-10-pkshih@realtek.com
This enables hw_scan function for 52c. The mechanism is similar to 52a
except that it adds modifications required for 6G channels and extends the
command length to make driver compatible to both newer and existing
firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-9-pkshih@realtek.com
8852c transmits packets with slow response in deep ps mode,
and lead to low throughput. We need to call tx_wake for
each pakcet to trigger firmware wake earlier to avoid it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-8-pkshih@realtek.com
rtw8852c could support deep ps mode if the firmware version
is greater than 0.17.34.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-7-pkshih@realtek.com
With suitable response rate, it can acknowledge peer packets are received.
Otherwise, peer could re-transmit again due to missing of ACK frames.
To achieve this, refer to RX rate and CMAC table to choose the smaller
as initial response rate.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-6-pkshih@realtek.com
With one path TX for 1SS rate, it can transmit higher power in 6GHz band
to yield better performance in high attenuation circumstance.
Signed-off-by: Yi-Tang Chiu <chiuyitang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-5-pkshih@realtek.com
The range of calibration time of RX DCK is quite wide from ~40us to
~1300us by experiments, and probability is about 0.1% for the cases larger
than 1000us. Though it can retry calibration and get positive result, it
will spend more time. Therefore, enlarge it to avoid warning and duplicate
calibration.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-4-pkshih@realtek.com
Enable MU-MIMO interference cancellation (MUIC) to yield expected
performance of receiving MU-MIMO packets on 6GHz.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-3-pkshih@realtek.com
Since control register address for DIG are different per IC, add a new
struct rtw89_dig_regs in chip info for each IC to define their own address.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-2-pkshih@realtek.com
Originally, we show average signal strength. To support TX diversity, this
patch prepares strength per path, then we can decide TX path.
RSSI: -54 dBm (raw=112, prev=110) [-57, -52]
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908074140.39776-5-pkshih@realtek.com
Two fields, TX/RX ANT NUM, are introduced to address variant TX/RX antenna
number of hardware. For example, a 1x1 chip with TX diversity, TX NSS = 1
and TX/RX ANT NUM = 2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908074140.39776-3-pkshih@realtek.com
The definitions of bit fields in structure will be wrong in big-endian
platform, so use u32_get_bits() to access them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908074140.39776-2-pkshih@realtek.com
We can call this in one of two ways: through mac80211, where
we're already in an RCU read-side critical section, or from
some other code in the driver where this pointer can only be
NULL. In any case, we get a 'free' already protected pointer
to the sta through info->control.sta, so we can use it on
the stack without any further protection.
Remove the rcu_dereference() and critical section.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.e5bc20dd17bf.Ib570ff7fde33c2b6eddef493a3541fa04eb47181@changeid
These cause sparse warnings, and since the device generally
works in little endian we can assume the code is correct, so
just fix the casts accordingly. No binary changes on x86.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.3f72609a3825.If4048592701bf04981be1dab18eaaa339b2ea382@changeid
rtl8xxxu_queue_select() selects the wrong TX queues because it's
reading memory from the wrong address. It expects to find ieee80211_hdr
at skb->data, but that's not the case after skb_push(). Move the call
to rtl8xxxu_queue_select() before the call to skb_push().
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7fa4819a-4f20-b2af-b7a6-8ee01ac49295@gmail.com
Return value from brcmf_fil_iovar_data_set() and
brcmf_config_ap_mgmt_ie() directly instead of
taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220831132254.303697-1-cui.jinpeng2@zte.com.cn
Add HW and SDIO ids for use with the muRata 1YN (Cypress CYW43439).
Add the firmware mapping structures for the CYW43439 chipset.
The 43439 needs some things setup similar to the 43430 chipset.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220827024903.617294-1-marex@denx.de
Since the logic of the driver's error handling code has changed, the
previous dead store and checks are not needed.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220818073352.3156288-1-zheyuma97@gmail.com
The double `to' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220811120340.12968-1-wangborong@cdjrlc.com
The Chuwi Hi8 Pro tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43430a0-sdio.Default string-Default string.txt" as nvram file
which is way too generic.
The Chuwi Hi8 Pro uses the same Ampak AP6212 module as the Chuwi Vi8 Plus
and the nvram for the Vi8 Plus is already in linux-firmware, so point
the new DMI nvram filename quirk to the Vi8 Plus nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220810142333.141044-1-hdegoede@redhat.com
Many devices ship with a nvram ccode value of X2/XT/XU/XV/ALL which are
all special world-wide compatibility ccode-s. Most of these world-wide
ccode-s allow passive scan mode only for 2.4GHz channels 12-14,
only enabling them when an AP is seen on them.
Since linux-firmware has moved to the new cyfmac43430-sdio.bin +
cyfmac43430-sdio.clm_blob firmware files this no longer works and
43430 devices using e.g. an X2 ccode fail to connect to an AP on
channel 13.
Add the 43430 chip-id to the list of chips for which to use the ISO3166
country code + rev 0 as fallback in brcmf_translate_country_code() to
fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220810142328.141030-1-hdegoede@redhat.com
In preparation for FORTIFY_SOURCE performing run-time destination buffer
bounds checking for memcpy(), refactor the use of struct iwl_calib_result:
- Have struct iwl_calib_result contain struct iwl_calib_cmd since
functions expect to operate on the "data" flex array in "cmd", which
follows the "hdr" member.
- Switch argument passing around to use struct iwl_calib_cmd instead of
struct iwl_calib_hdr to prepare functions to see the "data" member.
- Change iwl_calib_set()'s "len" argument to a size_t since it is always
unsigned and is normally receiving the output of sizeof().
- Add an explicit length sanity check in iwl_calib_set().
- Adjust the memcpy() to avoid copying across the now visible composite
flex array structure.
This avoids the future run-time warning:
memcpy: detected field-spanning write (size 8) of single field "&res->hdr" (size 4)
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Reported-by: Andy Lavr <andy.lavr@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220901204558.2256458-1-keescook@chromium.org
One of my previous patches here changed the function prototype,
but since it was (half?) automated, I didn't update the docs.
Fix that now.
Fixes: b3e2130bf5 ("wifi: mac80211: change QoS settings API to take link into account")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By default, even in client mode, hwsim always had all links
active, where it then uses them in a round-robin fashion.
Re-enable that by activating all valid links work right after
the connection is authorized.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement an API function and debugfs file to switch
active links.
Also provide an async version of the API so drivers
can call it in arbitrary contexts, e.g. while in the
authorized callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The A-MSDU data needs to be stored per-link and aggregated into a single
value for the station. Add a new struct ieee_80211_sta_aggregates in
order to store this data and a new function
ieee80211_sta_recalc_aggregates to update the current data for the STA.
Note that in the non MLO case the pointer in ieee80211_sta will directly
reference the data in deflink.agg, which means that recalculation may be
skipped in that case.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add macros (and an exported function) to allow checking some
link RCU protected accesses that are happening in callbacks
from mac80211 and are thus under the correct lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In hwsim we now track when we receive NDP (or other frames
carrying a PM bit) to see if a link should be active, but
then of course we also need to transmit NDPs to at least
set a link to inactive when we deacivate it. Implement that
as well as sending an NDP when we activate a link, which
allows receiving frames before transmitting any.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a link_id parameter to ieee80211_nullfunc_get() to be
able to obtain a correctly addressed frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track the powersave bit on frames where we can look up
the STA by link addresses and set the links active or
inactive accordingly, and use this information to TX
only on links that are actually active in the peer.
Note that this doesn't implement powersave fully so
if no link is active things will not work right.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new API function ieee80211_find_sta_by_link_addrs()
that looks up the STA and link ID based on interface and
station link addresses.
We're going to use it for mac80211-hwsim to track on the
AP side which links are active.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to let the driver select active links and properly
make multi-link connections, as a first step isolate the
driver from inactive links, and set the active links to be
only the association link for client-side interfaces. For
AP side nothing changes since APs always have to have all
their links active.
To simplify things, update the for_each_sta_active_link()
API to include the appropriate vif pointer.
This also implies not allocating a chanctx for an inactive
link, which requires a few more changes.
Since we now no longer try to program multiple links to the
driver, remove the check in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SMPS power save mode needs to be per-link rather than being shared
for all links. As such, move it into struct ieee80211_link_sta.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use rx->link_sta everywhere instead of accessing the default link.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we have a link_sta pointer in the rx struct
we also need to fill it in all the cases. It didn't
matter so much until now as we weren't using it, but
the code should really be able to assume that if the
rx.sta is set, so is rx.link_sta.
Fixes: ccdde7c74f ("wifi: mac80211: properly implement MLO key handling")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
