In the kfd_process_device_init_vm function, a valid error code is now
returned when the associated Process Address Space ID (PASID) is not
present.
If the address space virtual memory (avm) does not have an associated
PASID, the function sets the ret variable to -EINVAL before proceeding
to the error handling section. This ensures that the calling function,
such as kfd_ioctl_acquire_vm, can appropriately handle the error,
thereby preventing any issues during virtual memory initialization.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_process.c:1694 kfd_process_device_init_vm()
warn: missing error code 'ret'
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_process.c
1647 int kfd_process_device_init_vm(struct kfd_process_device *pdd,
1648 struct file *drm_file)
1649 {
...
1690
1691 if (unlikely(!avm->pasid)) {
1692 dev_warn(pdd->dev->adev->dev, "WARN: vm %p has no pasid associated",
1693 avm);
--> 1694 goto err_get_pasid;
ret = -EINVAL?
1695 }
Fixes: 8544374c0f ("drm/amdkfd: Have kfd driver use same PASID values from graphic driver")
Reported by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: Xiaogang Chen <xiaogang.chen@amd.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no need to check adev for sure.
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move code about checking aca enabled to the cper init/fini function
to make code clean.
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If firmware supported NPS modes are available through CAP register, use
those values for supported NPS modes.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On SMU v13.0.12, always query the firmware to get the current power
limit as it could be updated through other means also.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add ring reset function callback for JPEG4_0_3 to
recover from job timeouts without a full gpu reset.
V2:
- sched->ready flag shouldn't be modified by HW backend (Christian)
V3:
- Dont modifying sched/job-submission state from HW backend (Christian)
- Implement per-core reset sequence
V4:
- Dont create reset_mask sysfs and return -EOPNOTSUPP on VFs (Lijo)
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add core reset control registers for JPEG4_0_3
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RLCG Register Access is a way for virtual functions to safely access GPU
registers in a virtualized environment., including TLB flushes and
register reads. When multiple threads or VFs try to access the same
registers simultaneously, it can lead to race conditions. By using the
RLCG interface, the driver can serialize access to the registers. This
means that only one thread can access the registers at a time,
preventing conflicts and ensuring that operations are performed
correctly. Additionally, when a low-priority task holds a mutex that a
high-priority task needs, ie., If a thread holding a spinlock tries to
acquire a mutex, it can lead to priority inversion. register access in
amdgpu_virt_rlcg_reg_rw especially in a fast code path is critical.
The call stack shows that the function amdgpu_virt_rlcg_reg_rw is being
called, which attempts to acquire the mutex. This function is invoked
from amdgpu_sriov_wreg, which in turn is called from
gmc_v11_0_flush_gpu_tlb.
The [ BUG: Invalid wait context ] indicates that a thread is trying to
acquire a mutex while it is in a context that does not allow it to sleep
(like holding a spinlock).
Fixes the below:
[ 253.013423] =============================
[ 253.013434] [ BUG: Invalid wait context ]
[ 253.013446] 6.12.0-amdstaging-drm-next-lol-050225 #14 Tainted: G U OE
[ 253.013464] -----------------------------
[ 253.013475] kworker/0:1/10 is trying to lock:
[ 253.013487] ffff9f30542e3cf8 (&adev->virt.rlcg_reg_lock){+.+.}-{3:3}, at: amdgpu_virt_rlcg_reg_rw+0xf6/0x330 [amdgpu]
[ 253.013815] other info that might help us debug this:
[ 253.013827] context-{4:4}
[ 253.013835] 3 locks held by kworker/0:1/10:
[ 253.013847] #0: ffff9f3040050f58 ((wq_completion)events){+.+.}-{0:0}, at: process_one_work+0x3f5/0x680
[ 253.013877] #1: ffffb789c008be40 ((work_completion)(&wfc.work)){+.+.}-{0:0}, at: process_one_work+0x1d6/0x680
[ 253.013905] #2: ffff9f3054281838 (&adev->gmc.invalidate_lock){+.+.}-{2:2}, at: gmc_v11_0_flush_gpu_tlb+0x198/0x4f0 [amdgpu]
[ 253.014154] stack backtrace:
[ 253.014164] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Tainted: G U OE 6.12.0-amdstaging-drm-next-lol-050225 #14
[ 253.014189] Tainted: [U]=USER, [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
[ 253.014203] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 11/18/2024
[ 253.014224] Workqueue: events work_for_cpu_fn
[ 253.014241] Call Trace:
[ 253.014250] <TASK>
[ 253.014260] dump_stack_lvl+0x9b/0xf0
[ 253.014275] dump_stack+0x10/0x20
[ 253.014287] __lock_acquire+0xa47/0x2810
[ 253.014303] ? srso_alias_return_thunk+0x5/0xfbef5
[ 253.014321] lock_acquire+0xd1/0x300
[ 253.014333] ? amdgpu_virt_rlcg_reg_rw+0xf6/0x330 [amdgpu]
[ 253.014562] ? __lock_acquire+0xa6b/0x2810
[ 253.014578] __mutex_lock+0x85/0xe20
[ 253.014591] ? amdgpu_virt_rlcg_reg_rw+0xf6/0x330 [amdgpu]
[ 253.014782] ? sched_clock_noinstr+0x9/0x10
[ 253.014795] ? srso_alias_return_thunk+0x5/0xfbef5
[ 253.014808] ? local_clock_noinstr+0xe/0xc0
[ 253.014822] ? amdgpu_virt_rlcg_reg_rw+0xf6/0x330 [amdgpu]
[ 253.015012] ? srso_alias_return_thunk+0x5/0xfbef5
[ 253.015029] mutex_lock_nested+0x1b/0x30
[ 253.015044] ? mutex_lock_nested+0x1b/0x30
[ 253.015057] amdgpu_virt_rlcg_reg_rw+0xf6/0x330 [amdgpu]
[ 253.015249] amdgpu_sriov_wreg+0xc5/0xd0 [amdgpu]
[ 253.015435] gmc_v11_0_flush_gpu_tlb+0x44b/0x4f0 [amdgpu]
[ 253.015667] gfx_v11_0_hw_init+0x499/0x29c0 [amdgpu]
[ 253.015901] ? __pfx_smu_v13_0_update_pcie_parameters+0x10/0x10 [amdgpu]
[ 253.016159] ? srso_alias_return_thunk+0x5/0xfbef5
[ 253.016173] ? smu_hw_init+0x18d/0x300 [amdgpu]
[ 253.016403] amdgpu_device_init+0x29ad/0x36a0 [amdgpu]
[ 253.016614] amdgpu_driver_load_kms+0x1a/0xc0 [amdgpu]
[ 253.017057] amdgpu_pci_probe+0x1c2/0x660 [amdgpu]
[ 253.017493] local_pci_probe+0x4b/0xb0
[ 253.017746] work_for_cpu_fn+0x1a/0x30
[ 253.017995] process_one_work+0x21e/0x680
[ 253.018248] worker_thread+0x190/0x330
[ 253.018500] ? __pfx_worker_thread+0x10/0x10
[ 253.018746] kthread+0xe7/0x120
[ 253.018988] ? __pfx_kthread+0x10/0x10
[ 253.019231] ret_from_fork+0x3c/0x60
[ 253.019468] ? __pfx_kthread+0x10/0x10
[ 253.019701] ret_from_fork_asm+0x1a/0x30
[ 253.019939] </TASK>
v2: s/spin_trylock/spin_lock_irqsave to be safe (Christian).
Fixes: e864180ee4 ("drm/amdgpu: Add lock around VF RLCG interface")
Cc: lin cao <lin.cao@amd.com>
Cc: Jingwen Chen <Jingwen.Chen2@amd.com>
Cc: Victor Skvortsov <victor.skvortsov@amd.com>
Cc: Zhigang Luo <zhigang.luo@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Summary:
* Add support for disconnected eDP streams
* Add log for MALL entry on DCN32x
* Add DCC/Tiling reset helper for DCN and DCE
* Guard against setting dispclk low when active
* Other minor fixes
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP may not be connected to the GPU on driver start causing
fail enumeration.
[How]
Move the virtual signal type check before the eDP connector
signal check.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In current HPO DP2 implementation, driver would enable/disable DIG
encoder when configuring HPO DP2. Therefore, usb4 dp tunnelling should
not use the DIG encoder if the corresponded phy is used by a HPO DP2
stream.
[HOW]
A DP2 stream is treated as a dig stream.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should never apply a minimum dispclk value while in prepare_bandwidth
or while displays are active. This is always an optimization for when
all displays are disabled.
[How]
Defer dispclk optimization until safe_to_lower = true and display_count
reaches 0.
Since 0 has a special value in this logic (ie. no dispclk required)
we also need adjust the logic that clamps it for the actual request
to PMFW.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Reviewed-by: Leo Chen <leo.chen@amd.com>
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
BT2020 YCbCr input is not handled properly when full range
quantization is used and limited range is not supported at all.
[How]
- Add enums for BT2020 YCbCr limited/full range
- Add limited range CSC matrix
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Robert Mader <robert.mader@collabora.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add a dyndbg log entry to check whether the driver requested scanout
from MALL cache to PMFW via DMCUB
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The informative structure needs to be extended by the total number of DPPs
required per each active plane.
The new informative field is going to be used as a statistical indicator.
[How]
The dml2_core_calcs_get_informative() routine must count a total number of DPPs.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Oleh Kuzhylnyi <okuzhyln@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The latest DP spec requires the DP TX to read DPCD F0000h through F0009h
when detecting LTTPR capabilities for the first time.
[How]
Update LTTPR cap retrieval to read up to F0009h (two more bytes than the
previous F0007h), and store the LTTPR ALPM capabilities.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Add a message so users know the stream will be used for seamless boot.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Introduce the DCC and Tiling reset callback to all DCN versions that can
call it.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rename dc_plane_force_update_for_panic to
dc_plane_force_dcc_and_tiling_disable to describe the function operation
in the name. Also, this function might be used in other contexts, and a
more generic name can be helpful for this purpose.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit introduces a function helper for resetting DCN/DCE DCC and
tiling. Those functions are generic for their respective DCN/DCE, so
they were added to the oldest version of each architecture.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 13437c9160.
Reason to revert: idle power regression found in testing.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't try to operate on a drm_wb_connector as an amdgpu_dm_connector.
While dereferencing aconnector->base will "work" it's wrong and
might lead to unknown bad things. Just... don't.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
By default, DCN HW is in idle optimized state which does not allow access
to PHY registers. If BIOS powers up the DCN, it is fine because they will
power up everything. Only exit idle optimized state when not taking control
from VBIOS.
Fixes: be704e5ef4 ("Revert "drm/amd/display: Exit idle optimizations before attempt to access PHY"")
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During disabling the transcoder in DP 128b/132b mode (both in case of an
MST master transcoder and in case of SST) the transcoder function must
be first disabled without changing any other field in the register (in
particular leaving the DDI port and mode select fields unchanged) and
clearing the DDI port and mode select fields separately, later during
the disabling sequences. Fix the sequence accordingly.
Bspec: 54128, 65448, 68849
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 79a6734cd5 ("drm/i915/ddi: disable trancoder port select for 128b/132b SST")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217223828.1166093-3-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 2ed653c7b8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
At the end of a 128b/132b link training sequence, the HW expects the
transcoder training pattern to be set to TPS2 and from that to normal
mode (disabling the training pattern). Transitioning from TPS1 directly
to normal mode leaves the transcoder in a stuck state, resulting in
page-flip timeouts later in the modeset sequence.
Atm, in case of a failure during link training, the transcoder may be
still set to output the TPS1 pattern. Later the transcoder is then set
from TPS1 directly to normal mode in intel_dp_stop_link_train(), leading
to modeset failures later as described above. Fix this by setting the
training patter to TPS2, if the link training failed at any point.
The clue in the specification about the above HW behavior is the
explicit mention that TPS2 must be set after the link training sequence
(and there isn't a similar requirement specified for the 8b/10b link
training), see the Bspec links below.
v2: Add bspec aspect/link to the commit log. (Jani)
Bspec: 54128, 65448, 68849
Cc: stable@vger.kernel.org # v5.18+
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217223828.1166093-2-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 8b4bbaf8dd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
During disabling the transcoder in DP 128b/132b mode (both in case of an
MST master transcoder and in case of SST) the transcoder function must
be first disabled without changing any other field in the register (in
particular leaving the DDI port and mode select fields unchanged) and
clearing the DDI port and mode select fields separately, later during
the disabling sequences. Fix the sequence accordingly.
Bspec: 54128, 65448, 68849
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 79a6734cd5 ("drm/i915/ddi: disable trancoder port select for 128b/132b SST")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217223828.1166093-3-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
At the end of a 128b/132b link training sequence, the HW expects the
transcoder training pattern to be set to TPS2 and from that to normal
mode (disabling the training pattern). Transitioning from TPS1 directly
to normal mode leaves the transcoder in a stuck state, resulting in
page-flip timeouts later in the modeset sequence.
Atm, in case of a failure during link training, the transcoder may be
still set to output the TPS1 pattern. Later the transcoder is then set
from TPS1 directly to normal mode in intel_dp_stop_link_train(), leading
to modeset failures later as described above. Fix this by setting the
training patter to TPS2, if the link training failed at any point.
The clue in the specification about the above HW behavior is the
explicit mention that TPS2 must be set after the link training sequence
(and there isn't a similar requirement specified for the 8b/10b link
training), see the Bspec links below.
v2: Add bspec aspect/link to the commit log. (Jani)
Bspec: 54128, 65448, 68849
Cc: stable@vger.kernel.org # v5.18+
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217223828.1166093-2-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Error handling was wrong, causing unhandled transaction restart errors.
check_directory_size() was also inefficient, since keys in multiple
snapshots would be iterated over once for every snapshot. Convert it to
the same scheme used for i_sectors and subdir count checking.
Cc: Hongbo Li <lihongbo22@huawei.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
When compiling without CONFIG_IA32_EMULATION, there can be some errors:
drivers/accel/amdxdna/amdxdna_mailbox.c: In function ‘mailbox_release_msg’:
drivers/accel/amdxdna/amdxdna_mailbox.c:197:2: error: implicit declaration
of function ‘kfree’.
197 | kfree(mb_msg);
| ^~~~~
drivers/accel/amdxdna/amdxdna_mailbox.c: In function ‘xdna_mailbox_send_msg’:
drivers/accel/amdxdna/amdxdna_mailbox.c:418:11: error:implicit declaration
of function ‘kzalloc’.
418 | mb_msg = kzalloc(sizeof(*mb_msg) + pkg_size, GFP_KERNEL);
| ^~~~~~~
Add the missing include.
Fixes: b87f920b93 ("accel/amdxdna: Support hardware mailbox")
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Lizhi Hou <lizhi.hou@amd.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250211015354.3388171-1-suhui@nfschina.com
If the reparse point was not handled (indicated by the -EOPNOTSUPP from
ops->parse_reparse_point() call) but reparse tag is of type name surrogate
directory type, then treat is as a new mount point.
Name surrogate reparse point represents another named entity in the system.
From SMB client point of view, this another entity is resolved on the SMB
server, and server serves its content automatically. Therefore from Linux
client point of view, this name surrogate reparse point of directory type
crosses mount point.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
This would help to track and detect by caller if the reparse point type was
processed or not.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
If a file size has bits 0x410 = ATTR_DIRECTORY | ATTR_REPARSE set
then during queryinfo (stat) the file is regarded as a directory
and subsequent opens can fail. A simple test example is trying
to open any file 1040 bytes long when mounting with "posix"
(SMB3.1.1 POSIX/Linux Extensions).
The cause of this bug is that Attributes field in smb2_file_all_info
struct occupies the same place that EndOfFile field in
smb311_posix_qinfo, and sometimes the latter struct is incorrectly
processed as if it was the first one.
Reported-by: Oleh Nykyforchyn <oleh.nyk@gmail.com>
Tested-by: Oleh Nykyforchyn <oleh.nyk@gmail.com>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with flexible-array members in the
middle of other structs, we use the `__struct_group()` helper to
separate the flexible arrays from the rest of the members in the
flexible structures. We then use the newly created tagged `struct
smb2_file_link_info_hdr` and `struct smb2_file_rename_info_hdr`
to replace the type of the objects causing trouble: `rename_info`
and `link_info` in `struct smb2_compound_vars`.
We also want to ensure that when new members need to be added to the
flexible structures, they are always included within the newly created
tagged structs. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
So, with these changes, fix 86 of the following warnings:
fs/smb/client/cifsglob.h:2335:36: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
fs/smb/client/cifsglob.h:2334:38: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
drm_atomic_helper_wait_for_flip_done() will wait for pages flips on all
CRTCs affected by a given commit. It takes the drm_atomic_state being
committed as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-26-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_wait_for_dependencies() is the final part of a commit
and signals it completion. It takes the drm_atomic_state being committed
as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-25-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_cleanup_planes() is one of the final part of a commit,
and will free up all plane resources used in the previous commit. It
takes the drm_atomic_state being committed as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-24-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_wait_for_vblanks() waits for vblank events on all the
CRTCs affected by a commit. It takes the drm_atomic_state being
committed as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-23-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_commit_hw_done() signals hardware completion of a
given commit. It takes the drm_atomic_state being committed as a
parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-22-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_fake_vblank() fake a vblank event if needed when a new
commit is being applied. It takes the drm_atomic_state being committed
as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-21-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_commit_writebacks() updates all writeback connectors
affected by a new commit. It takes the drm_atomic_state being committed
as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-20-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_bridge_chain_enable() enables all bridges affected by a new
commit. It takes the drm_atomic_state being committed as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-19-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_bridge_chain_pre_enable() enables all bridges affected by
a new commit. It takes the drm_atomic_state being committed as a
parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-18-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_commit_modeset_enables() enables all outputs affected
by a new commit. It takes the drm_atomic_state being committed as a
parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-17-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_commit_planes() updates all planes affected by a new
commit. It takes the drm_atomic_state being committed as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-16-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
crtc_set_mode() deals with calling the modeset related hooks for CRTC,
connectors and bridges if and when a new commit changes them. It takes
the drm_atomic_state being committed as a parameter.
However, that parameter name is called as old_state, which is pretty
confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-15-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_update_legacy_modeset_state() updates all the legacy
modeset pointers a connector, encoder or CRTC might have with the ones
being setup by a given commit. It takes the drm_atomic_state being
committed as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-14-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_bridge_chain_post_disable() disables all bridges affected by
a new commit. It takes the drm_atomic_state being committed as a
parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-13-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_bridge_chain_disable() disables all bridges affected by a new
commit. It takes the drm_atomic_state being committed as a parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-12-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
disable_outputs() disables all connectors and CRTCs affected by a
commit. It takes the drm_atomic_state being committed as a parameter.
However, that parameter name is called as old_state, which is pretty
confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-11-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_modeset_disables() disables all the outputs affected
by a commit. It takes the drm_atomic_state being committed as a
parameter.
However, that parameter name is called (and documented) as old_state,
which is pretty confusing. Let's rename that variable as state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-10-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
