If a VF has been configured and the user later clears all QoS settings,
the vport element remains in the firmware QoS tree. This leads to
inconsistent behavior compared to VFs that were never configured, since
the FW assumes that unconfigured VFs are outside the QoS hierarchy.
As a result, the bandwidth share across VFs may differ, even though
none of them appear to have any configuration.
Align the driver behavior with the FW expectation by destroying the
vport QoS element when all configurations are removed.
Fixes: c9497c9890 ("net/mlx5: Add support for setting VF min rate")
Fixes: cf7e73770d ("net/mlx5: Manage TC arbiter nodes and implement full support for tc-bw")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20250820133209.389065-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When changing parent of a node/leaf with tc-bw configured, the code
saves and restores tc-bw values. However, it was reading the converted
hardware bw_share values (where 0 becomes 1) instead of the original
user values, causing incorrect tc-bw calculations after parent change.
Store original tc-bw values in the node structure and use them directly
for save/restore operations.
Fixes: cf7e73770d ("net/mlx5: Manage TC arbiter nodes and implement full support for tc-bw")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the driver creates a default group (`node0`) and attaches
all vports to it unless the user explicitly sets a parent group. As a
result, when a user configures tx_share on a group and tx_share on
a VF, the expectation is for the group and the VF to share bandwidth
relatively. However, since the VF is not connected to the same parent
(but to the default node), the proportional share logic is not applied
correctly.
To fix this, remove the default group (`node0`) and instead connect
vports directly to the root TSAR when no parent is specified. This
ensures that vports and groups share the same root scheduler and their
tx_share values are compared directly under the same hierarchy.
Fixes: 0fe132eac3 ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adjust the vport number by the base ECVF vport number so the port
attributes start at 0. Previously the port attributes would start 1
after the maximum number of host VFs.
Fixes: dc13180824 ("net/mlx5: Enable devlink port for embedded cpu VF vports")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the power supply's power budget is not defined in the device tree,
the current code still requests power and configures the PSE manager
with a 0W power limit, which is undesirable behavior.
Skip power budget configuration entirely when the budget is zero,
avoiding unnecessary power requests and preventing invalid 0W limits
from being set on the PSE manager.
Fixes: 359754013e ("net: pse-pd: pd692x0: Add support for PSE PI priority feature")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250820133321.841054-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a resource leak where manager power budgets were freed on both
success and error paths during manager setup. Power budgets should
only be freed on error paths after regulator registration or during
driver removal.
Refactor cleanup logic by extracting OF node cleanup and power budget
freeing into separate helper functions for better maintainability.
Fixes: 359754013e ("net: pse-pd: pd692x0: Add support for PSE PI priority feature")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250820132708.837255-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Octeontx2/CN10K silicon supports generating a 256-bit key per packet.
The specific fields to be extracted from a packet for key generation
are configurable via a Key Extraction (MKEX) Profile.
The AF driver scans the configured extraction profile to ensure that
fields from upper layers do not overwrite fields from lower layers in
the key.
Example Packet Field Layout:
LA: DMAC + SMAC
LB: VLAN
LC: IPv4/IPv6
LD: TCP/UDP
Valid MKEX Profile Configuration:
LA -> DMAC -> key_offset[0-5]
LC -> SIP -> key_offset[20-23]
LD -> SPORT -> key_offset[30-31]
Invalid MKEX profile configuration:
LA -> DMAC -> key_offset[0-5]
LC -> SIP -> key_offset[20-23]
LD -> SPORT -> key_offset[2-3] // Overlaps with DMAC field
In another scenario, if the MKEX profile is configured to extract
the SPI field from both AH and ESP headers at the same key offset,
the driver rejecting this configuration. In a regular traffic,
ipsec packet will be having either AH(LD) or ESP (LE). This patch
relaxes the check for the same.
Fixes: 12aa0a3b93 ("octeontx2-af: Harden rule validation.")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250820063919.1463518-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test various combinations of zero-length records.
Unfortunately, kernel cannot be coerced into producing those,
so hardcode the ciphertext messages in the test.
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20250820021952.143068-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each recvmsg() call must process either
- only contiguous DATA records (any number of them)
- one non-DATA record
If the next record has different type than what has already been
processed we break out of the main processing loop. If the record
has already been decrypted (which may be the case for TLS 1.3 where
we don't know type until decryption) we queue the pending record
to the rx_list. Next recvmsg() will pick it up from there.
Queuing the skb to rx_list after zero-copy decrypt is not possible,
since in that case we decrypted directly to the user space buffer,
and we don't have an skb to queue (darg.skb points to the ciphertext
skb for access to metadata like length).
Only data records are allowed zero-copy, and we break the processing
loop after each non-data record. So we should never zero-copy and
then find out that the record type has changed. The corner case
we missed is when the initial record comes from rx_list, and it's
zero length.
Reported-by: Muhammad Alifa Ramdhan <ramdhan@starlabs.sg>
Reported-by: Billy Jheng Bing-Jhong <billy@starlabs.sg>
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20250820021952.143068-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SW hash computed by airoha_ppe_foe_get_entry_hash routine (used for
foe_flow hlist) can theoretically produce collisions between two
different HW PPE entries.
In airoha_ppe_foe_insert_entry() if the collision occurs we will mark
the second PPE entry in the list as stale (setting the hw hash to 0xffff).
Stale entries are no more updated in airoha_ppe_foe_flow_entry_update
routine and so they are removed by Netfilter.
Fix the problem not marking the second entry as stale in
airoha_ppe_foe_insert_entry routine if we have already inserted the
brand new entry in the PPE table and let Netfilter remove real stale
entries according to their timestamp.
Please note this is just a theoretical issue spotted reviewing the code
and not faced running the system.
Fixes: cd53f62261 ("net: airoha: Add L2 hw acceleration support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250818-airoha-en7581-hash-collision-fix-v1-1-d190c4b53d1c@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Hangbin Liu says:
====================
bonding: fix negotiation flapping in 802.3ad passive mode
This patch fixes unstable LACP negotiation when bonding is configured in
passive mode (`lacp_active=off`).
Previously, the actor would stop sending LACPDUs after initial negotiation
succeeded, leading to the partner timing out and restarting the negotiation
cycle. This resulted in continuous LACP state flapping.
The fix ensures the passive actor starts sending periodic LACPDUs after
receiving the first LACPDU from the partner, in accordance with IEEE
802.1AX-2020 section 6.4.1.
====================
Link: https://patch.msgid.link/20250815062000.22220-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a selftest to verify bonding behavior when `lacp_active` is set to `off`.
The test checks the following:
- The passive LACP bond should not send LACPDUs before receiving a partner's
LACPDU.
- The transmitted LACPDUs must not include the active flag.
- After transitioning to EXPIRED and DEFAULTED states, the passive side should
still not initiate LACPDUs.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250815062000.22220-4-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When `lacp_active` is set to `off`, the bond operates in passive mode, meaning
it only "speaks when spoken to." However, the current kernel implementation
only sends an LACPDU in response when the partner's state changes.
As a result, once LACP negotiation succeeds, the actor stops sending LACPDUs
until the partner times out and sends an "expired" LACPDU. This causes
continuous LACP state flapping.
According to IEEE 802.1AX-2014, 6.4.13 Periodic Transmission machine. The
values of Partner_Oper_Port_State.LACP_Activity and
Actor_Oper_Port_State.LACP_Activity determine whether periodic transmissions
take place. If either or both parameters are set to Active LACP, then periodic
transmissions occur; if both are set to Passive LACP, then periodic
transmissions do not occur.
To comply with this, we remove the `!bond->params.lacp_active` check in
`ad_periodic_machine()`. Instead, we initialize the actor's port's
`LACP_STATE_LACP_ACTIVITY` state based on `lacp_active` setting.
Additionally, we avoid setting the partner's state to
`LACP_STATE_LACP_ACTIVITY` in the EXPIRED state, since we should not assume
the partner is active by default.
This ensures that in passive mode, the bond starts sending periodic LACPDUs
after receiving one from the partner, and avoids flapping due to inactivity.
Fixes: 3a755cd8b7 ("bonding: add new option lacp_active")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250815062000.22220-3-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The port's actor_oper_port_state activity flag should be updated immediately
after changing the lacp_active option to reflect the current mode correctly.
Fixes: 3a755cd8b7 ("bonding: add new option lacp_active")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250815062000.22220-2-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This reverts commit db400061b5.
This commit can cause a Devicetree ABI break for older DTS files that rely this
flag for RMII configuration. Adding this back in ensures that the older
DTBs will not break.
Fixes: db400061b5 ("net: cadence: macb: sama7g5_emac: Remove USARIO CLKEN flag")
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Link: https://patch.msgid.link/20250819163236.100680-1-Ryan.Wanner@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To prevent timing attacks, MACs need to be compared in constant time.
Use the appropriate helper function for this.
Fixes: bf355b8d2c ("ipv6: sr: add core files for SR HMAC support")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Link: https://patch.msgid.link/20250818202724.15713-1-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Receiving HSR frame with insufficient space to hold HSR tag in the skb
can result in a crash (kernel BUG):
[ 45.390915] skbuff: skb_under_panic: text:ffffffff86f32cac len:26 put:14 head:ffff888042418000 data:ffff888042417ff4 tail:0xe end:0x180 dev:bridge_slave_1
[ 45.392559] ------------[ cut here ]------------
[ 45.392912] kernel BUG at net/core/skbuff.c:211!
[ 45.393276] Oops: invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN NOPTI
[ 45.393809] CPU: 1 UID: 0 PID: 2496 Comm: reproducer Not tainted 6.15.0 #12 PREEMPT(undef)
[ 45.394433] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[ 45.395273] RIP: 0010:skb_panic+0x15b/0x1d0
<snip registers, remove unreliable trace>
[ 45.402911] Call Trace:
[ 45.403105] <IRQ>
[ 45.404470] skb_push+0xcd/0xf0
[ 45.404726] br_dev_queue_push_xmit+0x7c/0x6c0
[ 45.406513] br_forward_finish+0x128/0x260
[ 45.408483] __br_forward+0x42d/0x590
[ 45.409464] maybe_deliver+0x2eb/0x420
[ 45.409763] br_flood+0x174/0x4a0
[ 45.410030] br_handle_frame_finish+0xc7c/0x1bc0
[ 45.411618] br_handle_frame+0xac3/0x1230
[ 45.413674] __netif_receive_skb_core.constprop.0+0x808/0x3df0
[ 45.422966] __netif_receive_skb_one_core+0xb4/0x1f0
[ 45.424478] __netif_receive_skb+0x22/0x170
[ 45.424806] process_backlog+0x242/0x6d0
[ 45.425116] __napi_poll+0xbb/0x630
[ 45.425394] net_rx_action+0x4d1/0xcc0
[ 45.427613] handle_softirqs+0x1a4/0x580
[ 45.427926] do_softirq+0x74/0x90
[ 45.428196] </IRQ>
This issue was found by syzkaller.
The panic happens in br_dev_queue_push_xmit() once it receives a
corrupted skb with ETH header already pushed in linear data. When it
attempts the skb_push() call, there's not enough headroom and
skb_push() panics.
The corrupted skb is put on the queue by HSR layer, which makes a
sequence of unintended transformations when it receives a specific
corrupted HSR frame (with incomplete TAG).
Fix it by dropping and consuming frames that are not long enough to
contain both ethernet and hsr headers.
Alternative fix would be to check for enough headroom before skb_push()
in br_dev_queue_push_xmit().
In the reproducer, this is injected via AF_PACKET, but I don't easily
see why it couldn't be sent over the wire from adjacent network.
Further Details:
In the reproducer, the following network interface chain is set up:
┌────────────────┐ ┌────────────────┐
│ veth0_to_hsr ├───┤ hsr_slave0 ┼───┐
└────────────────┘ └────────────────┘ │
│ ┌──────┐
├─┤ hsr0 ├───┐
│ └──────┘ │
┌────────────────┐ ┌────────────────┐ │ │┌────────┐
│ veth1_to_hsr ┼───┤ hsr_slave1 ├───┘ └┤ │
└────────────────┘ └────────────────┘ ┌┼ bridge │
││ │
│└────────┘
│
┌───────┐ │
│ ... ├──────┘
└───────┘
To trigger the events leading up to crash, reproducer sends a corrupted
HSR frame with incomplete TAG, via AF_PACKET socket on 'veth0_to_hsr'.
The first HSR-layer function to process this frame is
hsr_handle_frame(). It and then checks if the
protocol is ETH_P_PRP or ETH_P_HSR. If it is, it calls
skb_set_network_header(skb, ETH_HLEN + HSR_HLEN), without checking that
the skb is long enough. For the crashing frame it is not, and hence the
skb->network_header and skb->mac_len fields are set incorrectly,
pointing after the end of the linear buffer.
I will call this a BUG#1 and it is what is addressed by this patch. In
the crashing scenario before the fix, the skb continues to go down the
hsr path as follows.
hsr_handle_frame() then calls this sequence
hsr_forward_skb()
fill_frame_info()
hsr->proto_ops->fill_frame_info()
hsr_fill_frame_info()
hsr_fill_frame_info() contains a check that intends to check whether the
skb actually contains the HSR header. But the check relies on the
skb->mac_len field which was erroneously setup due to BUG#1, so the
check passes and the execution continues back in the hsr_forward_skb():
hsr_forward_skb()
hsr_forward_do()
hsr->proto_ops->get_untagged_frame()
hsr_get_untagged_frame()
create_stripped_skb_hsr()
In create_stripped_skb_hsr(), a copy of the skb is created and is
further corrupted by operation that attempts to strip the HSR tag in a
call to __pskb_copy().
The skb enters create_stripped_skb_hsr() with ethernet header pushed in
linear buffer. The skb_pull(skb_in, HSR_HLEN) thus pulls 6 bytes of
ethernet header into the headroom, creating skb_in with a headroom of
size 8. The subsequent __pskb_copy() then creates an skb with headroom
of just 2 and skb->len of just 12, this is how it looks after the copy:
gdb) p skb->len
$10 = 12
(gdb) p skb->data
$11 = (unsigned char *) 0xffff888041e45382 "\252\252\252\252\252!\210\373",
(gdb) p skb->head
$12 = (unsigned char *) 0xffff888041e45380 ""
It seems create_stripped_skb_hsr() assumes that ETH header is pulled
in the headroom when it's entered, because it just pulls HSR header on
top. But that is not the case in our code-path and we end up with the
corrupted skb instead. I will call this BUG#2
*I got confused here because it seems that under no conditions can
create_stripped_skb_hsr() work well, the assumption it makes is not true
during the processing of hsr frames - since the skb_push() in
hsr_handle_frame to skb_pull in hsr_deliver_master(). I wonder whether I
missed something here.*
Next, the execution arrives in hsr_deliver_master(). It calls
skb_pull(ETH_HLEN), which just returns NULL - the SKB does not have
enough space for the pull (as it only has 12 bytes in total at this
point).
*The skb_pull() here further suggests that ethernet header is meant
to be pushed through the whole hsr processing and
create_stripped_skb_hsr() should pull it before doing the HSR header
pull.*
hsr_deliver_master() then puts the corrupted skb on the queue, it is
then picked up from there by bridge frame handling layer and finally
lands in br_dev_queue_push_xmit where it panics.
Cc: stable@kernel.org
Fixes: 48b491a5cc ("net: hsr: fix mac_len checks")
Reported-by: syzbot+a81f2759d022496b40ab@syzkaller.appspotmail.com
Signed-off-by: Jakub Acs <acsjakub@amazon.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250819082842.94378-1-acsjakub@amazon.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The WARN_ON trigger based on !cl->leaf.q->q.qlen is unnecessary in
htb_activate. htb_dequeue_tree already accounts for that scenario.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: William Liu <will@willsroot.io>
Reviewed-by: Savino Dicanosa <savy@syst3mfailure.io>
Link: https://patch.msgid.link/20250819033632.579854-1-will@willsroot.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following setup can trigger a WARNING in htb_activate due to
the condition: !cl->leaf.q->q.qlen
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: htb default 1
tc class add dev lo parent 1: classid 1:1 \
htb rate 64bit
tc qdisc add dev lo parent 1:1 handle f: \
cake memlimit 1b
ping -I lo -f -c1 -s64 -W0.001 127.0.0.1
This is because the low memlimit leads to a low buffer_limit, which
causes packet dropping. However, cake_enqueue still returns
NET_XMIT_SUCCESS, causing htb_enqueue to call htb_activate with an
empty child qdisc. We should return NET_XMIT_CN when packets are
dropped from the same tin and flow.
I do not believe return value of NET_XMIT_CN is necessary for packet
drops in the case of ack filtering, as that is meant to optimize
performance, not to signal congestion.
Fixes: 046f6fd5da ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: William Liu <will@willsroot.io>
Reviewed-by: Savino Dicanosa <savy@syst3mfailure.io>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20250819033601.579821-1-will@willsroot.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ksz9477_hsr_join() is called once to setup the HSR port membership, but
the port can be enabled later, or disabled and enabled back and the port
membership is not set correctly inside ksz_update_port_member(). The
added code always use the correct HSR port membership for HSR port that
is enabled.
Fixes: 2d61298fdd ("net: dsa: microchip: Enable HSR offloading for KSZ9477")
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Łukasz Majewski <lukma@nabladev.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20250819010457.563286-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-08-15 (ice, ixgbe, igc)
For ixgbe:
Jason Xing corrects a condition in which improper decrement can cause
improper budget value.
Maciej extends down states in which XDP cannot transmit and excludes XDP
rings from Tx hang checks.
For igc:
VladikSS moves setting of hardware device information to allow for proper
check of device ID.
v1: https://lore.kernel.org/20250815204205.1407768-1-anthony.l.nguyen@intel.com
====================
Link: https://patch.msgid.link/20250819222000.3504873-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Device ID comparison in igc_is_device_id_i226 is performed before
the ID is set, resulting in always failing check on init.
Before the patch:
* L1.2 is not disabled on init
* L1.2 is properly disabled after suspend-resume cycle
With the patch:
* L1.2 is properly disabled both on init and after suspend-resume
How to test:
Connect to the 1G link with 300+ mbit/s Internet speed, and run
the download speed test, such as:
curl -o /dev/null http://speedtest.selectel.ru/1GB
Without L1.2 disabled, the speed would be no more than ~200 mbit/s.
With L1.2 disabled, the speed would reach 1 gbit/s.
Note: it's required that the latency between your host and the remote
be around 3-5 ms, the test inside LAN (<1 ms latency) won't trigger the
issue.
Link: https://lore.kernel.org/intel-wired-lan/15248b4f-3271-42dd-8e35-02bfc92b25e1@intel.com
Fixes: 0325143b59 ("igc: disable L1.2 PCI-E link substate to avoid performance issue")
Signed-off-by: ValdikSS <iam@valdikss.org.ru>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250819222000.3504873-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently ixgbe driver checks periodically in its watchdog subtask if
there is anything to be transmitted (considering both Tx and XDP rings)
under state of carrier not being 'ok'. Such event is interpreted as Tx
hang and therefore results in interface reset.
This is currently problematic for ndo_xdp_xmit() as it is allowed to
produce descriptors when interface is going through reset or its carrier
is turned off.
Furthermore, XDP rings should not really be objects of Tx hang
detection. This mechanism is rather a matter of ndo_tx_timeout() being
called from dev_watchdog against Tx rings exposed to networking stack.
Taking into account issues described above, let us have a two fold fix -
do not respect XDP rings in local ixgbe watchdog and do not produce Tx
descriptors in ndo_xdp_xmit callback when there is some problem with
carrier currently. For now, keep the Tx hang checks in clean Tx irq
routine, but adjust it to not execute for XDP rings.
Cc: Tobias Böhm <tobias.boehm@hetzner-cloud.de>
Reported-by: Marcus Wichelmann <marcus.wichelmann@hetzner-cloud.de>
Closes: https://lore.kernel.org/netdev/eca1880f-253a-4955-afe6-732d7c6926ee@hetzner-cloud.de/
Fixes: 6453073987 ("ixgbe: add initial support for xdp redirect")
Fixes: 33fdc82f08 ("ixgbe: add support for XDP_TX action")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Marcus Wichelmann <marcus.wichelmann@hetzner-cloud.de>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250819222000.3504873-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Resolve the budget negative overflow which leads to returning true in
ixgbe_xmit_zc even when the budget of descs are thoroughly consumed.
Before this patch, when the budget is decreased to zero and finishes
sending the last allowed desc in ixgbe_xmit_zc, it will always turn back
and enter into the while() statement to see if it should keep processing
packets, but in the meantime it unexpectedly decreases the value again to
'unsigned int (0--)', namely, UINT_MAX. Finally, the ixgbe_xmit_zc returns
true, showing 'we complete cleaning the budget'. That also means
'clean_complete = true' in ixgbe_poll.
The true theory behind this is if that budget number of descs are consumed,
it implies that we might have more descs to be done. So we should return
false in ixgbe_xmit_zc to tell napi poll to find another chance to start
polling to handle the rest of descs. On the contrary, returning true here
means job done and we know we finish all the possible descs this time and
we don't intend to start a new napi poll.
It is apparently against our expectations. Please also see how
ixgbe_clean_tx_irq() handles the problem: it uses do..while() statement
to make sure the budget can be decreased to zero at most and the negative
overflow never happens.
The patch adds 'likely' because we rarely would not hit the loop condition
since the standard budget is 256.
Fixes: 8221c5eba8 ("ixgbe: add AF_XDP zero-copy Tx support")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Priya Singh <priyax.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250819222000.3504873-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Parthiban Veerasooran says:
====================
Fixes on the Microchip's LAN865x driver
This patch series includes two bug fixes for the LAN865x Ethernet MAC-PHY
driver:
1. Fix missing transmit queue restart on device reopen
This patch addresses an issue where the transmit queue is not restarted
when the network interface is brought back up after being taken down
(e.g., via ip or ifconfig). As a result, packet transmission hangs
after the first down/up cycle. The fix ensures netif_start_queue() is
explicitly called in lan865x_net_open() to properly restart the queue
on every reopen.
2. Fix missing configuration in the Microchip LAN865x driver for silicon
revisions B0 and B1, as documented in Microchip Application Note AN1760
(Rev F, June 2024). These revisions require the MAC to be configured for
timestamping at the end of the Start of Frame Delimiter (SFD) and the
Timer Increment register to be set to 40 ns, corresponding to a 25 MHz
internal clock.
Both patches address issues introduced with the initial driver support and
are marked with the appropriate Fixes: tag.
====================
Link: https://patch.msgid.link/20250818060514.52795-1-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix missing configuration for LAN865x silicon revisions B0 and B1 as per
Microchip Application Note AN1760 (Rev F, June 2024).
The Timer Increment register was not being set, which is required for
accurate timestamping. As per the application note, configure the MAC to
set timestamping at the end of the Start of Frame Delimiter (SFD), and
set the Timer Increment register to 40 ns (corresponding to a 25 MHz
internal clock).
Link: https://www.microchip.com/en-us/application-notes/an1760
Fixes: 5cd2340cb6 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY")
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250818060514.52795-3-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This fixes an issue where the transmit queue is started implicitly only
the very first time the device is registered. When the device is taken
down and brought back up again (using `ip` or `ifconfig`), the transmit
queue is not restarted, causing packet transmission to hang.
Adding an explicit call to netif_start_queue() in lan865x_net_open()
ensures the transmit queue is properly started every time the device
is reopened.
Fixes: 5cd2340cb6 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY")
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20250818060514.52795-2-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mark Bloch says:
====================
mlx5 HWS fixes 2025-08-17
The following patch set focuses on hardware steering fixes
found by the team.
====================
Link: https://patch.msgid.link/20250817202323.308604-1-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Specifying the counter action is not enough, as it is used by multiple
counters that were allocated in a bulk. By omitting the offset, rules
will be associated with a different counter from the same bulk.
Subsequently, the CT subsystem checks the correct counter, assumes that
no traffic has triggered the rule, and ages out the rule. The end result
is intermittent offloading of long lived connections, as rules are aged
out then promptly re-added.
Fix this by specifying the correct offset along with the counter rule.
Fixes: 34eea5b12a ("net/mlx5e: CT: Add initial support for Hardware Steering")
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250817202323.308604-8-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During table creation, caller passes a UID using ft_attr. The UID
value was ignored, which leads to problems when the caller sets the
UID to a non-zero value, such as SHARED_RESOURCE_UID (0xffff) - the
internal FT objects will be created with UID=0.
Fixes: 0869701cba ("net/mlx5: HWS, added FW commands handling")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250817202323.308604-7-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If rule creation failed due to a full queue, due to timeout
in polling for completion, or due to matcher being in resize,
don't try to initiate rehash sequence - rehash would have
failed anyway.
Fixes: 2111bb970c ("net/mlx5: HWS, added backward-compatible API handling")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Vlad Dogaru <vdogaru@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250817202323.308604-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While moving the rules during rehash, CQ is not drained. The flush
and drain happens only when all the rules of a certain queue have been
moved. This behaviour can lead to accumulating large quantity of rules
that haven't got their completion yet, and eventually will fill up
the queue and will cause the rehash to fail.
Fix this problem by requiring drain once the number of outstanding
completions reaches a certain threshold.
Fixes: ef94799a87 ("net/mlx5: HWS, rework rehash loop")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Vlad Dogaru <vdogaru@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250817202323.308604-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Moving rules from matcher to matcher should not fail.
However, if it does fail due to various reasons, the error flow
should allow the kernel to continue functioning (albeit with broken
steering rules) instead of going into series of soft lock-ups or
some other problematic behaviour.
Similar to the simple rules, complex rules rehash logic suffers
from the same problems. This patch fixes the error flow for moving
complex rules:
- If new rule creation fails before it was even enqeued, do not
poll for completion
- If TIMEOUT happened while moving the rule, no point trying
to poll for completions for other rules. Something is broken,
completion won't come, just abort the rehash sequence.
- If some other completion with error received, don't give up.
Continue handling rest of the rules to minimize the damage.
- Make sure that the first error code that was received will
be actually returned to the caller instead of replacing it
with the generic error code.
All the aforementioned issues stem from the same bad error flow,
so no point fixing them one by one and leaving partially broken
code - fixing them in one patch.
Fixes: 17e0accac5 ("net/mlx5: HWS, support complex matchers")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Vlad Dogaru <vdogaru@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250817202323.308604-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Moving rules from matcher to matcher should not fail.
However, if it does fail due to various reasons, the error flow
should allow the kernel to continue functioning (albeit with broken
steering rules) instead of going into series of soft lock-ups or
some other problematic behaviour.
This patch fixes the error flow for moving simple rules:
- If new rule creation fails before it was even enqeued, do not
poll for completion
- If TIMEOUT happened while moving the rule, no point trying
to poll for completions for other rules. Something is broken,
completion won't come, just abort the rehash sequence.
- If some other completion with error received, don't give up.
Continue handling rest of the rules to minimize the damage.
- Make sure that the first error code that was received will
be actually returned to the caller instead of replacing it
with the generic error code.
All the aforementioned issues stem from the same bad error flow,
so no point fixing them one by one and leaving partially broken
code - fixing them in one patch.
Fixes: ef94799a87 ("net/mlx5: HWS, rework rehash loop")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Vlad Dogaru <vdogaru@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250817202323.308604-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The clk_tx_i clock must be supplied to the MAC for successful
initialization. On TH1520 SoC, the clock is provided by an internal
divider configured through GMAC_PLLCLK_DIV register when using RGMII
interface. However, currently we don't setup the divider before
initialization of the MAC, resulting in DMA reset failures if the
bootloader/firmware doesn't enable the divider,
[ 7.839601] thead-dwmac ffe7060000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 7.938338] thead-dwmac ffe7060000.ethernet eth0: PHY [stmmac-0:02] driver [RTL8211F Gigabit Ethernet] (irq=POLL)
[ 8.160746] thead-dwmac ffe7060000.ethernet eth0: Failed to reset the dma
[ 8.170118] thead-dwmac ffe7060000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 8.179384] thead-dwmac ffe7060000.ethernet eth0: __stmmac_open: Hw setup failed
Let's simply write GMAC_PLLCLK_DIV_EN to GMAC_PLLCLK_DIV to enable the
divider before MAC initialization. Note that for reconfiguring the
divisor, the divider must be disabled first and re-enabled later to make
sure the new divisor take effect.
The exact clock rate doesn't affect MAC's initialization according to my
test. It's set to the speed required by RGMII when the linkspeed is
1Gbps and could be reclocked later after link is up if necessary.
Fixes: 33a1a01e3a ("net: stmmac: Add glue layer for T-HEAD TH1520 SoC")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Link: https://patch.msgid.link/20250815104803.55294-1-ziyao@disroot.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A crash can occur if an ethtool operation is invoked
after shutdown() is called.
shutdown() is invoked during system shutdown to stop DMA operations
without performing expensive deallocations. It is discouraged to
unregister the netdev in this path, so the device may still be visible
to userspace and kernel helpers.
In gve, shutdown() tears down most internal data structures. If an
ethtool operation is dispatched after shutdown(), it will dereference
freed or NULL pointers, leading to a kernel panic. While graceful
shutdown normally quiesces userspace before invoking the reboot
syscall, forced shutdowns (as observed on GCP VMs) can still trigger
this path.
Fix by calling netif_device_detach() in shutdown().
This marks the device as detached so the ethtool ioctl handler
will skip dispatching operations to the driver.
Fixes: 974365e518 ("gve: Implement suspend/resume/shutdown")
Signed-off-by: Jordan Rhee <jordanrhee@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250818211245.1156919-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There was a problem when we received frames and the frames were
timestamped. The driver is configured to store the nanosecond part of
the timestmap in the ptp reserved bits and it would take the second part
by reading the LTC. The problem is that when reading the LTC we are in
atomic context and to read the second part will go over mdio bus which
might sleep, so we get an error.
The fix consists in actually put all the frames in a queue and start the
aux work and in that work to read the LTC and then calculate the full
received time.
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250818081029.1300780-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a user creates a dualpi2 qdisc it automatically sets a timer. This
timer will run constantly and update the qdisc's probability field.
The issue is that the timer acquires the qdisc root lock and runs in
hardirq. The qdisc root lock is also acquired in dev.c whenever a packet
arrives for this qdisc. Since the dualpi2 timer callback runs in hardirq,
it may interrupt the packet processing running in softirq. If that happens
and it runs on the same CPU, it will acquire the same lock and cause a
deadlock. The following splat shows up when running a kernel compiled with
lock debugging:
[ +0.000224] WARNING: inconsistent lock state
[ +0.000224] 6.16.0+ #10 Not tainted
[ +0.000169] --------------------------------
[ +0.000029] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[ +0.000000] ping/156 [HC0[0]:SC0[2]:HE1:SE0] takes:
[ +0.000000] ffff897841242110 (&sch->root_lock_key){?.-.}-{3:3}, at: __dev_queue_xmit+0x86d/0x1140
[ +0.000000] {IN-HARDIRQ-W} state was registered at:
[ +0.000000] lock_acquire.part.0+0xb6/0x220
[ +0.000000] _raw_spin_lock+0x31/0x80
[ +0.000000] dualpi2_timer+0x6f/0x270
[ +0.000000] __hrtimer_run_queues+0x1c5/0x360
[ +0.000000] hrtimer_interrupt+0x115/0x260
[ +0.000000] __sysvec_apic_timer_interrupt+0x6d/0x1a0
[ +0.000000] sysvec_apic_timer_interrupt+0x6e/0x80
[ +0.000000] asm_sysvec_apic_timer_interrupt+0x1a/0x20
[ +0.000000] pv_native_safe_halt+0xf/0x20
[ +0.000000] default_idle+0x9/0x10
[ +0.000000] default_idle_call+0x7e/0x1e0
[ +0.000000] do_idle+0x1e8/0x250
[ +0.000000] cpu_startup_entry+0x29/0x30
[ +0.000000] rest_init+0x151/0x160
[ +0.000000] start_kernel+0x6f3/0x700
[ +0.000000] x86_64_start_reservations+0x24/0x30
[ +0.000000] x86_64_start_kernel+0xc8/0xd0
[ +0.000000] common_startup_64+0x13e/0x148
[ +0.000000] irq event stamp: 6884
[ +0.000000] hardirqs last enabled at (6883): [<ffffffffa75700b3>] neigh_resolve_output+0x223/0x270
[ +0.000000] hardirqs last disabled at (6882): [<ffffffffa7570078>] neigh_resolve_output+0x1e8/0x270
[ +0.000000] softirqs last enabled at (6880): [<ffffffffa757006b>] neigh_resolve_output+0x1db/0x270
[ +0.000000] softirqs last disabled at (6884): [<ffffffffa755b533>] __dev_queue_xmit+0x73/0x1140
[ +0.000000]
other info that might help us debug this:
[ +0.000000] Possible unsafe locking scenario:
[ +0.000000] CPU0
[ +0.000000] ----
[ +0.000000] lock(&sch->root_lock_key);
[ +0.000000] <Interrupt>
[ +0.000000] lock(&sch->root_lock_key);
[ +0.000000]
*** DEADLOCK ***
[ +0.000000] 4 locks held by ping/156:
[ +0.000000] #0: ffff897842332e08 (sk_lock-AF_INET){+.+.}-{0:0}, at: raw_sendmsg+0x41e/0xf40
[ +0.000000] #1: ffffffffa816f880 (rcu_read_lock){....}-{1:3}, at: ip_output+0x2c/0x190
[ +0.000000] #2: ffffffffa816f880 (rcu_read_lock){....}-{1:3}, at: ip_finish_output2+0xad/0x950
[ +0.000000] #3: ffffffffa816f840 (rcu_read_lock_bh){....}-{1:3}, at: __dev_queue_xmit+0x73/0x1140
I am able to reproduce it consistently when running the following:
tc qdisc add dev lo handle 1: root dualpi2
ping -f 127.0.0.1
To fix it, make the timer run in softirq.
Fixes: 320d031ad6 ("sched: Struct definition and parsing of dualpi2 qdisc")
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250815135317.664993-1-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This lets NetworkManager/ModemManager know that this is a modem and
needs to be connected first.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://patch.msgid.link/20250814154214.250103-1-lkundrak@v3.sk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To enable HSR / Switch offload, certain configurations are needed.
Currently they are done inside icssg_change_mode(). This function only
gets called if we move from one mode to another without bringing the
links up / down.
Once in HSR / Switch mode, if we bring the links down and bring it back
up again. The callback sequence is,
- emac_ndo_stop()
Firmwares are stopped
- emac_ndo_open()
Firmwares are loaded
In this path icssg_change_mode() doesn't get called and as a result the
configurations needed for HSR / Switch is not done.
To fix this, put all these configurations in a separate function
icssg_enable_fw_offload() and call this from both icssg_change_mode()
and emac_ndo_open()
Fixes: 56375086d0 ("net: ti: icssg-prueth: Enable HSR Tx duplication, Tx Tag and Rx Tag offload")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20250814105106.1491871-1-danishanwar@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ppp_fill_forward_path() has two race conditions:
1. The ppp->channels list can change between list_empty() and
list_first_entry(), as ppp_lock() is not held. If the only channel
is deleted in ppp_disconnect_channel(), list_first_entry() may
access an empty head or a freed entry, and trigger a panic.
2. pch->chan can be NULL. When ppp_unregister_channel() is called,
pch->chan is set to NULL before pch is removed from ppp->channels.
Fix these by using a lockless RCU approach:
- Use list_first_or_null_rcu() to safely test and access the first list
entry.
- Convert list modifications on ppp->channels to their RCU variants and
add synchronize_net() after removal.
- Check for a NULL pch->chan before dereferencing it.
Fixes: f6efc675c9 ("net: ppp: resolve forwarding path for bridge pppoe devices")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://patch.msgid.link/20250814012559.3705-2-dqfext@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ensure ndo_fill_forward_path() is called with RCU lock held.
Fixes: 2830e31477 ("net: ethernet: mtk-ppe: fix traffic offload with bridged wlan")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://patch.msgid.link/20250814012559.3705-1-dqfext@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Matthieu Baerts says:
====================
mptcp: misc fixes for v6.17-rc
Here are various fixes:
- Patch 1: Better handling SKB extension allocation failures.
A fix for v5.7.
- Patches 2, 3: Avoid resetting MPTCP limits when flushing MPTCP
endpoints. With a validation in the selftests. Fixes for v5.7.
- Patches 4, 5, 6: Disallow '0' as ADD_ADDR retransmission timeout.
With a preparation patch, and a validation in the selftests.
Fixes for v5.11.
- Patches 8, 9: Fix C23 extension warnings in the selftests,
spotted by GCC. Fixes for v6.16.
====================
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-0-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GCC was complaining about the new label:
mptcp_inq.c:79:2: warning: label followed by a declaration is a C23 extension [-Wc23-extensions]
79 | int err = getaddrinfo(node, service, hints, res);
| ^
mptcp_sockopt.c:166:2: warning: label followed by a declaration is a C23 extension [-Wc23-extensions]
166 | int err = getaddrinfo(node, service, hints, res);
| ^
Simply declare 'err' before the label to avoid this warning.
Fixes: dd367e81b7 ("selftests: mptcp: sockopt: use IPPROTO_MPTCP for getaddrinfo")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-8-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GCC was complaining about the new label:
mptcp_connect.c:187:2: warning: label followed by a declaration is a C23 extension [-Wc23-extensions]
187 | int err = getaddrinfo(node, service, hints, res);
| ^
Simply declare 'err' before the label to avoid this warning.
Fixes: a862771d1a ("selftests: mptcp: use IPPROTO_MPTCP for getaddrinfo")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-7-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
