This patch adds Renesas R-mobile series common PM domain APIs.
R-mobile CPU can use/switch this API
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove variable and ignore return value of stv090x_chk_signal().
Tested by compilation only.
[mchehab@redhat.com: instead of reverting and applying V3,
applied just the diff patch, for the sake of a cleaner history]
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tegra's I2C2 controller can be routed to either the PTA or DDC pin group
on Seaboard. Define the pinctrl state nodes required to allow runtime
control of this routing. Instantiate a pinctrl-i2cmux I2C bus mux that
uses these pinctrl states.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Original work by Magnus Damm, tested and tweaked by Simon Horman
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The alternate setting number is not equal to the alternate setting index
in the interface alternate settings table. Use the alternate setting
number from the interface descriptor when calling usb_set_interface().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When video endpoint is configured as bulk, a ZLP is sent after every
video frames with size as multiple of 512 bytes. This is done so that
host can detect end of transfer and pass data for processing.
Still, frames that are multiple of 16K in size gets dropped. The ZLP
sent by camera is ignored by uvc_video_decode_bulk(). The makes sure
that the ZLP is not part of a video frame before ignoring it. If ZLP
follows a video frame, then it triggers completion callback.
[mchehab@redhat.com: Fix a small CodingStyle issue]
Signed-off-by: Jayakrishnan Memana <jayakrishnan.memana@maxim-ic.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several developers have reported that the lack of macros for the struct
uvc_xu_control_query query field in uvcvideo.h was confusing and forced
them to look at the driver source code to find out what applications
were supposed to pass in that field.
Add a comment to the header to clarify the expected usage of the query
field.
Reported-by: Paulo Assis <pj.assis@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On systems, using regulators to supply power to devices, if the REGULATOR
Kconfig option is disabled, regulator API stubs will be used, which often
suffices to bring a default configuration up. If REGULATOR is enabled but
respective regulator drivers are inactive, the real regulator API calls
will be used, which in the absence of drivers will fail to provide
services. This patch prevents such a problem on sh-mobile boards by
forcing REGULATOR_FIXED_VOLTAGE on if REGULATOR is selected.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Now of_regulator_match() returns without finding the match if match->of_node
is not NULL.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is multiple voltage input pins on device which
takes the voltage input for different voltage regulator.
Support to configure the voltage input supplied by
different regulator for each regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is to convert port_owners type from void * to struct dev_state *
in order to make code more readable.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MODULE_ALIAS() was missing from the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we're now relying on DAPM for things like enabling clocks when we
reparent the clocks for widgets we need to either use conditional routes
(which are expensive) or remove routes at runtime. Add a route removal
API to support this use case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If we add a new route at runtime then we'll need to recheck the connections
to the affected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Some userspace will open a PCM device and then configure mixers
for routing before triggering. This patch allows userspace to do
this sequence.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix spelling mistake in "High-Performance" option of twl6040 power mode.
Signed-off-by: Simon Wilson <simonwilson@google.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we set the bias level for all DAPM contexts when
changing level.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch rename struct ci13xxx_udc_driver and var with the type.
ci13xxx_platform_data reflect it's passed from platfrom driver.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_ style logging throughout soc_new_pcm()
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Codec shutdown performs a DAPM power sequence that might cause conflicts
and/or race conditions if another stream power event is running simultaneously.
Use card's dapm mutex to protect any potential race condition between them.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
allow this driver to be removed too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes, it will just free up some
code if we don't have hotplug.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
msm glue layer compiles on all arches just
fine. Let's drop the unnecessary ARCH check
so we have easier compile tests.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Dan Carpenter, there is a NULL check in udc_start() that
follows a dereference of the pointer that's being checked. However, at
that point udc pointer shouldn't ever be NULL and if it is, the dereference
should cause an oops.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since DT doesn't provide an idiomatic mechanism for enabling full
constraints and since it's much more natural with DT to provide them
just assume that a DT enabled system has full constraints.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch simply fixes some logging calls:
- Use KERN_INFO when printing the chip status.
- Add a missing space when logging the drxk_gate_ctrl call.
- Use the same logging text as always if the scu_command in GetQAMLockStatus fails.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently there are two different implementations (in the firmware) for
the QAM demodulator command: one takes 4 and the other takes 2
parameters. The driver shows an error in dmesg When using the
4-parameter command with firmware that implements the 2-parameter
command. Unfortunately this happens every time when chaning the
frequency (on DVB-C).
This patch simply makes configurable, how many command parameters will
be used. All existing drxk_config instances using the "drxk_a3.mc" were
updated because this firmware is the only loadable firmware where the
QAM demodulator command takes 4 parameters. Some firmwares in the ROM
might also use it. The drxk instances in the em28xx-dvb driver were also
updated to silence the warnings.
If no qam_demod_parameter_count is given in the drxk_config struct, then
the correct number of parameters will be auto-detected.
[mchehab@redhat.com: Fix a small CodingStyle issue at one comment]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IQM_AF_CLKNEG_CLKNEGDATA__M is 0x2 and
IQM_AF_CLKNEG_CLKNEGDATA_CLK_ADC_DATA_POS is 0. (clkNeg | 0x2) is never
equal to zero so the condition can never be true.
I consulted with Ralph Metzler and the '|' should be changed to a '&'.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
CC: Ralph Metzler <rjkm@metzlerbros.de>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When using urb->transfer_buffer we need to allocate physical contiguous buffers
for the entire transfer, which is pretty much guaranteed to fail with large
transfers.
Currently userspace works around this by breaking large transfers into multiple
urbs. For large bulk transfers this leads to all kind of complications.
This patch makes it possible for userspace to reliable submit large bulk
transfers to scatter-gather capable host controllers in one go, by using a
scatterlist to break the transfer up in managable chunks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few (new) usbdevfs capabilities which an application cannot
discover in any other way then checking the kernel version. There are 3
problems with this:
1) It is just not very pretty.
2) Given the tendency of enterprise distros to backport stuff it is not
reliable.
3) As discussed in length on the mailinglist, USBDEVFS_URB_BULK_CONTINUATION
does not work as it should when combined with USBDEVFS_URB_SHORT_NOT_OK
(which is its intended use) on devices attached to an XHCI controller.
So the availability of these features can be host controller dependent,
making depending on them based on the kernel version not a good idea.
This patch besides adding the new ioctl also adds flags for the following
existing capabilities:
USBDEVFS_CAP_ZERO_PACKET, available since 2.6.31
USBDEVFS_CAP_BULK_CONTINUATION, available since 2.6.32, except for XHCI
USBDEVFS_CAP_NO_PACKET_SIZE_LIM, available since 3.3
Note that this patch only does not advertise the USBDEVFS_URB_BULK_CONTINUATION
cap for XHCI controllers, bulk transfers with this flag set will still be
accepted when submitted to XHCI controllers.
Returning -EINVAL for them would break existing apps, and in most cases the
troublesome scenario wrt USBDEVFS_URB_SHORT_NOT_OK urbs on XHCI controllers
will never get hit, so this would break working use cases.
The disadvantage of not returning -EINVAL is that cases were it is causing
real trouble may go undetected / the cause of the trouble may be unclear,
but this is the best we can do.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iso data buffers may have holes in them if some packets were short, so for
iso urbs we should always copy the entire buffer, just like the regular
processcompl does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the dmaengine based Tegra APB DMA driver for
apbio access in place of legacy Tegra APB DMA.
The new driver is selected if legacy driver is not
selected and new DMA driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: s/pr_err/pr_debug/ in tegra_apb_dma_init; this condition is
expected to fire repeatedly before the DMA driver is available]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra20 HW issue with accessing APBIO registers (such
as fuse registers) directly from the CPU concurrently with
APB DMA accesses has been fixed in Tegra30 and later chips.
Access these registers directly from the CPU on Tegra30
and later, and apply the workaround only for Tegra20.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fixed coding style issue related to
prohibited space in drivers/usb/class/cdc-acm.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds clock gating to suspend and resume functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a logic error in OLPC CAFÉ NAND ready() function.
- Fix regression due to bitflip handling changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/265wACgkQdwG7hYl686MWGgCfdnxPKE/cJnjVm5wxlp+hTBLv
tbsAn3hpmrXhZNYNhQ+U34RDpw8V7SYc
=IEqd
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20120706' of git://git.infradead.org/linux-mtd
Pull two MTD fixes from David Woodhouse:
- Fix a logic error in OLPC CAFÉ NAND ready() function.
- Fix regression due to bitflip handling changes.
* tag 'for-linus-20120706' of git://git.infradead.org/linux-mtd:
mtd: cafe_nand: fix an & vs | mistake
mtd: nand: initialize bitflip_threshold prior to BBT scanning
Otherwise the code races with munmap (causing a use-after-free
of the vma) or with close (causing a use-after-free of the struct
file).
The bug was introduced by commit 90ed52ebe4 ("[PATCH] holepunch: fix
mmap_sem i_mutex deadlock")
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When tuner-xc2028 is not compiled as a module, dracut will
need to copy the firmware inside the initfs image.
So, use MODULE_FIRMWARE() to indicate such need.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If last_boosted_vcpu == 0, then we fall through all test cases and
may end up with all VCPUs pouncing on vcpu 0. With a large enough
guest, this can result in enormous runqueue lock contention, which
can prevent vcpu0 from running, leading to a livelock.
Changing < to <= makes sure we properly handle that case.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Make the mg_disk driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make the msi-laptop driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Lee, Chun-Yi <jlee@suse.com>
Pull ocfs2 fixes from Joel Becker.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
aio: make kiocb->private NUll in init_sync_kiocb()
ocfs2: Fix bogus error message from ocfs2_global_read_info
ocfs2: for SEEK_DATA/SEEK_HOLE, return internal error unchanged if ocfs2_get_clusters_nocache() or ocfs2_inode_lock() call failed.
ocfs2: use spinlock irqsave for downconvert lock.patch
ocfs2: Misplaced parens in unlikley
ocfs2: clear unaligned io flag when dio fails
