* pm-domains:
PM / domains: Remove one unnecessary blank line
PM / Domains: Return early for all errors in _genpd_power_off()
PM / Domains: Improve warn for multiple states but no governor
After commit 61cb5758d3 ("cpuidle: Add cpuidle.governor= command
line parameter") new cpuidle governors are not added to the list
of available governors, so governor selection via sysfs doesn't
work as expected (even though it is rarely used anyway).
Fix that by making cpuidle_register_governor() add new governors to
cpuidle_governors again.
Fixes: 61cb5758d3 ("cpuidle: Add cpuidle.governor= command line parameter")
Reported-by: Kees Cook <keescook@chromium.org>
Cc: 5.0+ <stable@vger.kernel.org> # 5.0+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit b8bd1581aa ("cpufreq: intel_pstate: Rework iowait
boosting to be less aggressive") the handling of the case when
the SCHED_CPUFREQ_IOWAIT flag is set again after a few iterations of
intel_pstate_update_util() is a bit inconsistent, because the
new value of cpu->iowait_boost may be lower than ONE_EIGHTH_FP
if it was set before, but has not dropped down to zero just yet.
Fix that up by ensuring that the new value of cpu->iowait_boost
will always be at least ONE_EIGHTH_FP then.
Fixes: b8bd1581aa ("cpufreq: intel_pstate: Rework iowait boosting to be less aggressive")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
At boot up, CPUFreq core performs a sanity check to see if the system is
running at a frequency defined in the frequency table of the CPU. If so,
we try to find a valid frequency (lowest frequency greater than the
currently programmed frequency) from the table and set it. When the call
reaches dev_pm_opp_set_rate(), it calls _find_freq_ceil(opp_table,
&old_freq) to find the previously configured OPP and this call also
updates the old_freq. This eventually sets the old_freq == freq (new
target requested by cpufreq core) and we skip updating the performance
state in this case.
Fix this by also updating the performance state when the old_freq ==
freq.
Fixes: ca1b5d77b1 ("OPP: Configure all required OPPs")
Cc: v5.0 <stable@vger.kernel.org> # v5.0
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit d856f39ac1cc ("PM / wakeup: Rework wakeup source timer
cancellation") wakeup_source_drop() is a trivial wrapper around
__pm_relax() and it has no users except for wakeup_source_destroy()
and wakeup_source_trash() which also has no users, so drop it along
with the latter and make wakeup_source_destroy() call __pm_relax()
directly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
If wakeup_source_add() is called right after wakeup_source_remove()
for the same wakeup source, timer_setup() may be called for a
potentially scheduled timer which is incorrect.
To avoid that, move the wakeup source timer cancellation from
wakeup_source_drop() to wakeup_source_remove().
Moreover, make wakeup_source_remove() clear the timer function after
canceling the timer to let wakeup_source_not_registered() treat
unregistered wakeup sources in the same way as the ones that have
never been registered.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
[ rjw: Subject, changelog, merged two patches together ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is strange to only return early for -EBUSY state and left other
errors to be still measured execution time.
As for error cases, the elapsed_ns computed actually is not quite
accurate and meaningful for governor to use. So let's simply return
for all error cases.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It's possible a PM domain defines only one state and it does not need
a governor to work. For such case, a warning actually is not necessary.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We seem to rely on the number of phandles specified in the
'required-opps' property to identify cases where a device is
associated with multiple power domains and hence would have
multiple virtual devices that have to be dealt with.
In cases where we do have devices with multiple power domains
but with only one of them being scalable, this logic seems to
fail.
Instead read the number of power domains from DT to identify
such cases.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a typo in the file description comment.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pxa_cpufreq_init_voltages() is marked __init but usually inlined into
the non-__init pxa_cpufreq_init() function. When building with clang,
it can stay as a standalone function in a discarded section, and produce
this warning:
WARNING: vmlinux.o(.text+0x616a00): Section mismatch in reference from the function pxa_cpufreq_init() to the function .init.text:pxa_cpufreq_init_voltages()
The function pxa_cpufreq_init() references
the function __init pxa_cpufreq_init_voltages().
This is often because pxa_cpufreq_init lacks a __init
annotation or the annotation of pxa_cpufreq_init_voltages is wrong.
Fixes: 50e77fcd79 ("ARM: pxa: remove __init from cpufreq_driver->init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Avoid the open-coding of the accounted time acquisition in
runtime_active|suspend_time_show() and make them call
pm_runtime_active|suspended_time() instead.
Note that this change also indirectly avoids holding dev->power.lock
around the do_div() computation and the sprintf() call which is an
additional improvement.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In a step to consolidate the code for fetching the PM-runtime
active/suspended time for a device, add a common function for that
and make the existing pm_runtime_suspended_time() call it.
Also add a corresponding pm_runtime_active_time() calling the new
common function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Changelog, function rename ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prefix all printk/pr_<level> messages with "PM: " to make the
logging a bit more consistent.
Miscellanea:
o Convert a few printks to pr_<level>
o Whitespace to align to open parentheses
o Remove embedded "PM: " from pr_debugs as pr_fmt adds it
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the formatting of the cpufreq_cpu_get() and cpufreq_cpu_put()
kerneldoc comments and rework them to be somewhat easier to follow.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The variance computation in get_typical_interval() may overflow if
the square of the value of diff exceeds the maximum for the int64_t
data type value which basically is the case when it is of the order
of UINT_MAX.
However, data points so far in the future don't matter for idle
state selection anyway, so change the initial threshold value in
get_typical_interval() to INT_MAX which will cause more "outlying"
data points to be discarded without affecting the selection result.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Update the PM-runtime framework to use ktime instead of
jiffies for accounting (Thara Gopinath, Vincent Guittot).
- Optimize the autosuspend code in the PM-runtime framework
somewhat (Ladislav Michl).
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla).
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki).
- Add Jacobsville support to the intel_idle driver (Zhang Rui).
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam).
- Add new cpufreq driver for Armada 8K (Gregory Clement).
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar,
Amit Kucheria).
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar).
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria).
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar).
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang).
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki).
- Clean up multiple cpufreq drivers (Yangtao Li).
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn).
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann,
Matthias Kaehlcke).
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui).
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar).
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TSKG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are PM-runtime framework changes to use ktime instead of jiffies
for accounting, new PM core flag to mark devices that don't need any
form of power management, cpuidle updates including driver API
documentation and a new governor, cpufreq updates including a new
driver for Armada 8K, thermal cleanups and more, some energy-aware
scheduling (EAS) enabling changes, new chips support in the intel_idle
and RAPL drivers and assorted cleanups in some other places.
Specifics:
- Update the PM-runtime framework to use ktime instead of jiffies for
accounting (Thara Gopinath, Vincent Guittot)
- Optimize the autosuspend code in the PM-runtime framework somewhat
(Ladislav Michl)
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla)
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki)
- Add Jacobsville support to the intel_idle driver (Zhang Rui)
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam)
- Add new cpufreq driver for Armada 8K (Gregory Clement)
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar, Amit
Kucheria)
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar)
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria)
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar)
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang)
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki)
- Clean up multiple cpufreq drivers (Yangtao Li)
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn)
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann, Matthias
Kaehlcke)
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui)
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar)
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li)"
* tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (80 commits)
cpufreq: kryo: Release OPP tables on module removal
cpufreq: ap806: add missing of_node_put after of_device_is_available
cpufreq: acpi-cpufreq: Report if CPU doesn't support boost technologies
cpufreq: Pass updated policy to driver ->setpolicy() callback
cpufreq: Fix two debug messages in cpufreq_set_policy()
cpufreq: Reorder and simplify cpufreq_update_policy()
cpufreq: Add kerneldoc comments for two core functions
PM / core: Add support to skip power management in device/driver model
cpufreq: intel_pstate: Rework iowait boosting to be less aggressive
cpufreq: intel_pstate: Eliminate intel_pstate_get_base_pstate()
cpufreq: intel_pstate: Avoid redundant initialization of local vars
powercap/intel_rapl: add Ice Lake mobile
ACPI / processor: Set P_LVL{2,3} idle state descriptions
cpufreq / cppc: Work around for Hisilicon CPPC cpufreq
ACPI / CPPC: Add a helper to get desired performance
cpufreq: davinci: move configuration to include/linux/platform_data
cpufreq: speedstep: convert BUG() to BUG_ON()
cpufreq: powernv: fix missing check of return value in init_powernv_pstates()
cpufreq: longhaul: remove unneeded semicolon
cpufreq: pcc-cpufreq: remove unneeded semicolon
..
Merge misc updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (159 commits)
tools/testing/selftests/proc/proc-self-syscall.c: remove duplicate include
proc: more robust bulk read test
proc: test /proc/*/maps, smaps, smaps_rollup, statm
proc: use seq_puts() everywhere
proc: read kernel cpu stat pointer once
proc: remove unused argument in proc_pid_lookup()
fs/proc/thread_self.c: code cleanup for proc_setup_thread_self()
fs/proc/self.c: code cleanup for proc_setup_self()
proc: return exit code 4 for skipped tests
mm,mremap: bail out earlier in mremap_to under map pressure
mm/sparse: fix a bad comparison
mm/memory.c: do_fault: avoid usage of stale vm_area_struct
writeback: fix inode cgroup switching comment
mm/huge_memory.c: fix "orig_pud" set but not used
mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC
mm/memcontrol.c: fix bad line in comment
mm/cma.c: cma_declare_contiguous: correct err handling
mm/page_ext.c: fix an imbalance with kmemleak
mm/compaction: pass pgdat to too_many_isolated() instead of zone
mm: remove zone_lru_lock() function, access ->lru_lock directly
...
Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection driver
is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8
release, I'm sending them along with the other updates.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0u1N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Arnd Bergmann:
"Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection
driver is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8 release,
I'm sending them along with the other updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
net: ethernet: ti: cpsw: deprecate cpsw-phy-sel driver
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
...
Two new SoC families are added this time.
Sugaya Taichi submitted support for the Milbeaut SoC family from
Socionext and explains:
"SC2000 is a SoC of the Milbeaut series. equipped with a DSP optimized for
computer vision. It also features advanced functionalities such as 360-degree,
real-time spherical stitching with multi cameras, image stabilization for
without mechanical gimbals, and rolling shutter correction. More detail is
below:
https://www.socionext.com/en/products/assp/milbeaut/SC2000.html"
Interestingly, this one has a history dating back to older chips
made by Socionext and previously Matsushita/Panasonic based on their
own mn10300 CPU architecture that was removed from the kernel last year.
Manivannan Sadhasivam adds support for another SoC family, this is the
Bitmain BM1880 chip used in the Sophon Edge TPU developer board.
The chip is intended for Deep Learning applications, and comes
with dual-core Arm Cortex-A53 to run Linux as well as a RISC-V
microcontroller core to control the tensor unit.
For the moment, the TPU is not accessible in mainline Linux, so
we treat it as a generic Arm SoC.
More information is available at https://www.sophon.ai/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HQS8
-----END PGP SIGNATURE-----
Merge tag 'armsoc-newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM new SoC family support from Arnd Bergmann:
"Two new SoC families are added this time.
Sugaya Taichi submitted support for the Milbeaut SoC family from
Socionext and explains:
"SC2000 is a SoC of the Milbeaut series. equipped with a DSP
optimized for computer vision. It also features advanced
functionalities such as 360-degree, real-time spherical stitching
with multi cameras, image stabilization for without mechanical
gimbals, and rolling shutter correction. More detail is below:
https://www.socionext.com/en/products/assp/milbeaut/SC2000.html"
Interestingly, this one has a history dating back to older chips made
by Socionext and previously Matsushita/Panasonic based on their own
mn10300 CPU architecture that was removed from the kernel last year.
Manivannan Sadhasivam adds support for another SoC family, this is the
Bitmain BM1880 chip used in the Sophon Edge TPU developer board.
The chip is intended for Deep Learning applications, and comes with
dual-core Arm Cortex-A53 to run Linux as well as a RISC-V
microcontroller core to control the tensor unit. For the moment, the
TPU is not accessible in mainline Linux, so we treat it as a generic
Arm SoC.
More information is available at
https://www.sophon.ai/"
* tag 'armsoc-newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: multi_v7_defconfig: add ARCH_MILBEAUT and ARCH_MILBEAUT_M10V
ARM: configs: Add Milbeaut M10V defconfig
ARM: dts: milbeaut: Add device tree set for the Milbeaut M10V board
clocksource/drivers/timer-milbeaut: Introduce timer for Milbeaut SoCs
dt-bindings: timer: Add Milbeaut M10V timer description
ARM: milbeaut: Add basic support for Milbeaut m10v SoC
dt-bindings: Add documentation for Milbeaut SoCs
dt-bindings: arm: Add SMP enable-method for Milbeaut
dt-bindings: sram: milbeaut: Add binding for Milbeaut smp-sram
MAINTAINERS: Add entry for Bitmain SoC platform
arm64: dts: bitmain: Add Sophon Egde board support
arm64: dts: bitmain: Add BM1880 SoC support
arm64: Add ARCH_BITMAIN platform
dt-bindings: arm: Document Bitmain BM1880 SoC
We regenerated the defconfig files for samsung, shmobile, lpc18xx,
lpc32xx, omap2, and nhk8815.
Lots of additional drivers added on samsung and nhk8815,
as well as the new pl110 driver on all machines that have it.
The remaining changes are mostly to enable newly added drivers,
and in case of imx8mq together with the SoC getting merged.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=YWHu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"We regenerated the defconfig files for samsung, shmobile, lpc18xx,
lpc32xx, omap2, and nhk8815.
Lots of additional drivers added on samsung and nhk8815, as well as
the new pl110 driver on all machines that have it.
The remaining changes are mostly to enable newly added drivers, and in
case of imx8mq together with the SoC getting merged"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: spear3xx_defconfig: Activate PL111 DRM driver
ARM: nhk8815_defconfig: Add new options
ARM: nhk8815_defconfig: Update defconfig
ARM: pxa: remove CONFIG_SND_PXA2XX_AC97 in pxa_defconfig
ARM: defconfig: integrator: Switch to DRM
arm64: defconfig: Add IMX2+ watchdog
arm64: defconfig: Enable PFUZE100 regulator
arm64: defconfig: enable NXP FlexSPI driver
arm64: defconfig: Add i.MX8MQ boot necessary configs
arm64: defconfig: add imx8qxp support
arm64: defconfig: add i.MX system controller RTC support
arm64: defconfig: Enable Tegra TCU
arm64: defconfig: Enable MAX8973 regulator
ARM: socfpga_defconfig: enable BLK_DEV_LOOP config option
ARM: defconfig: lpc32xx: enable DRM simple panel driver
ARM: defconfig: lpc32xx: enable fixed voltage regulator support
arm64: defconfig: Enable SUN6I Camera sensor interface
arm64: defconfig: Enable I2C_GPIO
ARM: omap2plus_defconfig: Update for moved options
ARM: omap2plus_defconfig: Update for dropped options
...
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging processor
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for
Rich Graphics Applications".
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power
Tools GmbH, based on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based
machine used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed
ast2500 baseboard management controller. This is for running on
the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet
switch used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development
system in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely
virtual platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both
in 32-bit and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a,
in 96Boards enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes include
updates for
- STMicroelectronics stm32mp1, which was now formally
launched last week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1goV
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging
processor:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics
Applications":
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC:
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power Tools GmbH, based
on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based machine
used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed ast2500
baseboard management controller. This is for running on the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet switch
used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development system
in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual
platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit
and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards
enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes
include updates for
- STMicroelectronics stm32mp1, which was now formally launched last
week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits)
ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
arm64: dts: sprd: Remove wildcard compatible string
arm64: dts: sprd: Add SC27XX fuel gauge device
arm64: dts: sprd: Add SC2731 charger device
arm64: dts: sprd: Add ADC calibration support
arm64: dts: sprd: Remove PMIC INTC irq trigger type
arm64: dts: rockchip: Enable tsadc device on rock960
ARM: dts: rockchip: add chosen node on veyron devices
...
The APM X-Gene platform is now maintained by folks from Ampere
computing that took over the product line a while ago, this gets
reflected in the MAINTAINERS file.
Cleanups continue on the older mach-davinci and mach-pxa platform,
to get them to be more like the modern ones. For pxa, we
now remove the Raumfeld platform code as it now works with
device tree based booting.
i.MX adds a couple new features for the i.MX7ULP SoC
Mediatek gains support for a new SoC: MT7629 is a new wireless
router platform, following MT7623.
Aside from those, there are the usual minor cleanups and bugfixes
across several platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vxwd
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The APM X-Gene platform is now maintained by folks from Ampere
computing that took over the product line a while ago, this gets
reflected in the MAINTAINERS file.
Cleanups continue on the older mach-davinci and mach-pxa platform, to
get them to be more like the modern ones. For pxa, we now remove the
Raumfeld platform code as it now works with device tree based booting.
i.MX adds a couple new features for the i.MX7ULP SoC
Mediatek gains support for a new SoC: MT7629 is a new wireless router
platform, following MT7623.
Aside from those, there are the usual minor cleanups and bugfixes
across several platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (49 commits)
MAINTAINERS: Update Ampere email address
usb: ohci-da8xx: remove unused callbacks from platform data
ARM: davinci: da830-evm: remove legacy usb helpers
ARM: davinci: omapl138-hawk: remove legacy usb helpers
usb: ohci-da8xx: add vbus and overcurrent gpios
ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
usb: ohci-da8xx: add a helper pointer to &pdev->dev
usb: ohci-da8xx: add a new line after local variables
arm64: meson: enable g12a clock controller
MAINTAINERS: Add entry for uDPU board
ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
arm: mediatek: add MT7629 smp bring up code
Revert "ARM: mediatek: add MT7623a smp bringup code"
dt-bindings: soc: fix typo of MT8173 power dt-bindings
ARM: meson: remove COMMON_CLK_AMLOGIC selection
arm64: meson: remove COMMON_CLK_AMLOGIC selection
ARM: lpc32xx: remove platform data of ARM PL111 LCD controller
ARM: lpc32xx: remove platform data of ARM PL180 SD/MMC controller
ARM: lpc32xx: Use kmemdup to replace duplicating its implementation
...
Only a few small changes this time:
- Michael S. Tsirkin cleans up linux/mman.h
- Mike Rapoport found a typo
I had originally merged another cleanup series for I/O accessors from
Hugo Lefeuvre as well, but dropped it after the discussion of the barrier
semantics and some conflicts. I expect this series to get merged for a
later release though.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=C9p7
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"Only a few small changes this time:
- Michael S. Tsirkin cleans up linux/mman.h
- Mike Rapoport found a typo
I had originally merged another cleanup series for I/O accessors from
Hugo Lefeuvre as well, but dropped it after the discussion of the
barrier semantics and some conflicts. I expect this series to get
merged for a later release though"
* tag 'asm-generic-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/page.h: fix typo in #error text requiring a real asm/page.h
arch: move common mmap flags to linux/mman.h
drm: tweak header name
x86/mpx: tweak header name
Here is one more patch on top of the y2038 changes already pulled
for linux-5.1, for some reason this had escaped all testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/MC2
-----END PGP SIGNATURE-----
Merge tag 'y2038-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground
Pull y2038 build fix for compat mode from Arnd Bergmann:
"Here is one more patch on top of the y2038 changes already pulled for
linux-5.1, for some reason this had escaped all testing"
* tag 'y2038-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground:
ipc: Fix building compat mode without sysvipc
Pull x86 alternative instruction updates from Ingo Molnar:
"Small RDTSCP opimization, enabled by the newly added ALTERNATIVE_3(),
and other small improvements"
* 'x86-alternatives-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/TSC: Use RDTSCP
x86/alternatives: Add an ALTERNATIVE_3() macro
x86/alternatives: Print containing function
x86/alternatives: Add macro comments
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- refcount conversions
- Solve the rq->leaf_cfs_rq_list can of worms for real.
- improve power-aware scheduling
- add sysctl knob for Energy Aware Scheduling
- documentation updates
- misc other changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
kthread: Do not use TIMER_IRQSAFE
kthread: Convert worker lock to raw spinlock
sched/fair: Use non-atomic cpumask_{set,clear}_cpu()
sched/fair: Remove unused 'sd' parameter from select_idle_smt()
sched/wait: Use freezable_schedule() when possible
sched/fair: Prune, fix and simplify the nohz_balancer_kick() comment block
sched/fair: Explain LLC nohz kick condition
sched/fair: Simplify nohz_balancer_kick()
sched/topology: Fix percpu data types in struct sd_data & struct s_data
sched/fair: Simplify post_init_entity_util_avg() by calling it with a task_struct pointer argument
sched/fair: Fix O(nr_cgroups) in the load balancing path
sched/fair: Optimize update_blocked_averages()
sched/fair: Fix insertion in rq->leaf_cfs_rq_list
sched/fair: Add tmp_alone_branch assertion
sched/core: Use READ_ONCE()/WRITE_ONCE() in move_queued_task()/task_rq_lock()
sched/debug: Initialize sd_sysctl_cpus if !CONFIG_CPUMASK_OFFSTACK
sched/pelt: Skip updating util_est when utilization is higher than CPU's capacity
sched/fair: Update scale invariance of PELT
sched/fair: Move the rq_of() helper function
sched/core: Convert task_struct.stack_refcount to refcount_t
...
Pull perf updates from Ingo Molnar:
"Lots of tooling updates - too many to list, here's a few highlights:
- Various subcommand updates to 'perf trace', 'perf report', 'perf
record', 'perf annotate', 'perf script', 'perf test', etc.
- CPU and NUMA topology and affinity handling improvements,
- HW tracing and HW support updates:
- Intel PT updates
- ARM CoreSight updates
- vendor HW event updates
- BPF updates
- Tons of infrastructure updates, both on the build system and the
library support side
- Documentation updates.
- ... and lots of other changes, see the changelog for details.
Kernel side updates:
- Tighten up kprobes blacklist handling, reduce the number of places
where developers can install a kprobe and hang/crash the system.
- Fix/enhance vma address filter handling.
- Various PMU driver updates, small fixes and additions.
- refcount_t conversions
- BPF updates
- error code propagation enhancements
- misc other changes"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (238 commits)
perf script python: Add Python3 support to syscall-counts-by-pid.py
perf script python: Add Python3 support to syscall-counts.py
perf script python: Add Python3 support to stat-cpi.py
perf script python: Add Python3 support to stackcollapse.py
perf script python: Add Python3 support to sctop.py
perf script python: Add Python3 support to powerpc-hcalls.py
perf script python: Add Python3 support to net_dropmonitor.py
perf script python: Add Python3 support to mem-phys-addr.py
perf script python: Add Python3 support to failed-syscalls-by-pid.py
perf script python: Add Python3 support to netdev-times.py
perf tools: Add perf_exe() helper to find perf binary
perf script: Handle missing fields with -F +..
perf data: Add perf_data__open_dir_data function
perf data: Add perf_data__(create_dir|close_dir) functions
perf data: Fail check_backup in case of error
perf data: Make check_backup work over directories
perf tools: Add rm_rf_perf_data function
perf tools: Add pattern name checking to rm_rf
perf tools: Add depth checking to rm_rf
perf data: Add global path holder
...
Pull locking updates from Ingo Molnar:
"The biggest part of this tree is the new auto-generated atomics API
wrappers by Mark Rutland.
The primary motivation was to allow instrumentation without uglifying
the primary source code.
The linecount increase comes from adding the auto-generated files to
the Git space as well:
include/asm-generic/atomic-instrumented.h | 1689 ++++++++++++++++--
include/asm-generic/atomic-long.h | 1174 ++++++++++---
include/linux/atomic-fallback.h | 2295 +++++++++++++++++++++++++
include/linux/atomic.h | 1241 +------------
I preferred this approach, so that the full call stack of the (already
complex) locking APIs is still fully visible in 'git grep'.
But if this is excessive we could certainly hide them.
There's a separate build-time mechanism to determine whether the
headers are out of date (they should never be stale if we do our job
right).
Anyway, nothing from this should be visible to regular kernel
developers.
Other changes:
- Add support for dynamic keys, which removes a source of false
positives in the workqueue code, among other things (Bart Van
Assche)
- Updates to tools/memory-model (Andrea Parri, Paul E. McKenney)
- qspinlock, wake_q and lockdep micro-optimizations (Waiman Long)
- misc other updates and enhancements"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (48 commits)
locking/lockdep: Shrink struct lock_class_key
locking/lockdep: Add module_param to enable consistency checks
lockdep/lib/tests: Test dynamic key registration
lockdep/lib/tests: Fix run_tests.sh
kernel/workqueue: Use dynamic lockdep keys for workqueues
locking/lockdep: Add support for dynamic keys
locking/lockdep: Verify whether lock objects are small enough to be used as class keys
locking/lockdep: Check data structure consistency
locking/lockdep: Reuse lock chains that have been freed
locking/lockdep: Fix a comment in add_chain_cache()
locking/lockdep: Introduce lockdep_next_lockchain() and lock_chain_count()
locking/lockdep: Reuse list entries that are no longer in use
locking/lockdep: Free lock classes that are no longer in use
locking/lockdep: Update two outdated comments
locking/lockdep: Make it easy to detect whether or not inside a selftest
locking/lockdep: Split lockdep_free_key_range() and lockdep_reset_lock()
locking/lockdep: Initialize the locks_before and locks_after lists earlier
locking/lockdep: Make zap_class() remove all matching lock order entries
locking/lockdep: Reorder struct lock_class members
locking/lockdep: Avoid that add_chain_cache() adds an invalid chain to the cache
...
Pull EFI updates from Ingo Molnar:
"The main EFI changes in this cycle were:
- Use 32-bit alignment for efi_guid_t
- Allow the SetVirtualAddressMap() call to be omitted
- Implement earlycon=efifb based on existing earlyprintk code
- Various minor fixes and code cleanups from Sai, Ard and me"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Fix build error due to enum collision between efi.h and ima.h
efi/x86: Convert x86 EFI earlyprintk into generic earlycon implementation
x86: Make ARCH_USE_MEMREMAP_PROT a generic Kconfig symbol
efi/arm/arm64: Allow SetVirtualAddressMap() to be omitted
efi: Replace GPL license boilerplate with SPDX headers
efi/fdt: Apply more cleanups
efi: Use 32-bit alignment for efi_guid_t
efi/memattr: Don't bail on zero VA if it equals the region's PA
x86/efi: Mark can_free_region() as an __init function
As John Stultz noticed, my y2038 syscall series caused a link
failure when CONFIG_SYSVIPC is disabled but CONFIG_COMPAT is
enabled:
arch/arm64/kernel/sys32.o:(.rodata+0x960): undefined reference to `__arm64_compat_sys_old_semctl'
arch/arm64/kernel/sys32.o:(.rodata+0x980): undefined reference to `__arm64_compat_sys_old_msgctl'
arch/arm64/kernel/sys32.o:(.rodata+0x9a0): undefined reference to `__arm64_compat_sys_old_shmctl'
Add the missing entries in kernel/sys_ni.c for the new system
calls.
Cc: Laura Abbott <labbott@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This cpupower update for Linux 5.1-rc1 consists of a patch to add
support to display boost frequency separately from Abhishek Goel.
-----BEGIN PGP SIGNATURE-----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=Gmfv
-----END PGP SIGNATURE-----
Merge tag 'linux-cpupower-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux
Pull cpupower updates for 5.1-rc1 from Shuah Khan:
"This cpupower update for Linux 5.1-rc1 consists of a patch to add
support to display boost frequency separately from Abhishek Goel."
* tag 'linux-cpupower-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
tools/power/cpupower: Display boost frequency separately
/proc may not be mounted and test will exit successfully.
Ensure proc is mounted at /proc.
Link: http://lkml.kernel.org/r/20190209105613.GA10384@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start testing VM related fiels found in per-process files.
Do it by jiting small executable which brings its address space to
precisely known state, then comparing /proc/*/maps, smaps, smaps_rollup,
and statm files to expected values.
Currently only x86_64 is supported.
[adobriyan@gmail.com: exit correctly in /proc/*/maps test]
Link: http://lkml.kernel.org/r/20190206073659.GB15311@avx2
Link: http://lkml.kernel.org/r/20190203165806.GA14568@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using mremap() syscall in addition to MREMAP_FIXED flag, mremap()
calls mremap_to() which does the following:
1) unmaps the destination region where we are going to move the map
2) If the new region is going to be smaller, we unmap the last part
of the old region
Then, we will eventually call move_vma() to do the actual move.
move_vma() checks whether we are at least 4 maps below max_map_count
before going further, otherwise it bails out with -ENOMEM. The problem
is that we might have already unmapped the vma's in steps 1) and 2), so
it is not possible for userspace to figure out the state of the vmas
after it gets -ENOMEM, and it gets tricky for userspace to clean up
properly on error path.
While it is true that we can return -ENOMEM for more reasons (e.g: see
may_expand_vm() or move_page_tables()), I think that we can avoid this
scenario if we check early in mremap_to() if the operation has high
chances to succeed map-wise.
Should that not be the case, we can bail out before we even try to unmap
anything, so we make sure the vma's are left untouched in case we are
likely to be short of maps.
The thumb-rule now is to rely on the worst-scenario case we can have.
That is when both vma's (old region and new region) are going to be
split in 3, so we get two more maps to the ones we already hold (one per
each). If current map count + 2 maps still leads us to 4 maps below the
threshold, we are going to pass the check in move_vma().
Of course, this is not free, as it might generate false positives when
it is true that we are tight map-wise, but the unmap operation can
release several vma's leading us to a good state.
Another approach was also investigated [1], but it may be too much
hassle for what it brings.
[1] https://lore.kernel.org/lkml/20190219155320.tkfkwvqk53tfdojt@d104.suse.de/
Link: http://lkml.kernel.org/r/20190226091314.18446-1-osalvador@suse.de
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Cyril Hrubis <chrubis@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
next_present_section_nr() could only return an unsigned number -1, so
just check it specifically where compilers will convert -1 to unsigned
if needed.
mm/sparse.c: In function 'sparse_init_nid':
mm/sparse.c:200:20: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
((section_nr >= 0) && \
^~
mm/sparse.c:478:2: note: in expansion of macro
'for_each_present_section_nr'
for_each_present_section_nr(pnum_begin, pnum) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~
mm/sparse.c:200:20: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
((section_nr >= 0) && \
^~
mm/sparse.c:497:2: note: in expansion of macro
'for_each_present_section_nr'
for_each_present_section_nr(pnum_begin, pnum) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~
mm/sparse.c: In function 'sparse_init':
mm/sparse.c:200:20: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
((section_nr >= 0) && \
^~
mm/sparse.c:520:2: note: in expansion of macro
'for_each_present_section_nr'
for_each_present_section_nr(pnum_begin + 1, pnum_end) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~
Link: http://lkml.kernel.org/r/20190228181839.86504-1-cai@lca.pw
Fixes: c4e1be9ec1 ("mm, sparsemem: break out of loops early")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LTP testcase mtest06 [1] can trigger a crash on s390x running 5.0.0-rc8.
This is a stress test, where one thread mmaps/writes/munmaps memory area
and other thread is trying to read from it:
CPU: 0 PID: 2611 Comm: mmap1 Not tainted 5.0.0-rc8+ #51
Hardware name: IBM 2964 N63 400 (z/VM 6.4.0)
Krnl PSW : 0404e00180000000 00000000001ac8d8 (__lock_acquire+0x7/0x7a8)
Call Trace:
([<0000000000000000>] (null))
[<00000000001adae4>] lock_acquire+0xec/0x258
[<000000000080d1ac>] _raw_spin_lock_bh+0x5c/0x98
[<000000000012a780>] page_table_free+0x48/0x1a8
[<00000000002f6e54>] do_fault+0xdc/0x670
[<00000000002fadae>] __handle_mm_fault+0x416/0x5f0
[<00000000002fb138>] handle_mm_fault+0x1b0/0x320
[<00000000001248cc>] do_dat_exception+0x19c/0x2c8
[<000000000080e5ee>] pgm_check_handler+0x19e/0x200
page_table_free() is called with NULL mm parameter, but because "0" is a
valid address on s390 (see S390_lowcore), it keeps going until it
eventually crashes in lockdep's lock_acquire. This crash is
reproducible at least since 4.14.
Problem is that "vmf->vma" used in do_fault() can become stale. Because
mmap_sem may be released, other threads can come in, call munmap() and
cause "vma" be returned to kmem cache, and get zeroed/re-initialized and
re-used:
handle_mm_fault |
__handle_mm_fault |
do_fault |
vma = vmf->vma |
do_read_fault |
__do_fault |
vma->vm_ops->fault(vmf); |
mmap_sem is released |
|
| do_munmap()
| remove_vma_list()
| remove_vma()
| vm_area_free()
| # vma is released
| ...
| # same vma is allocated
| # from kmem cache
| do_mmap()
| vm_area_alloc()
| memset(vma, 0, ...)
|
pte_free(vma->vm_mm, ...); |
page_table_free |
spin_lock_bh(&mm->context.lock);|
<crash> |
Cache mm_struct to avoid using potentially stale "vma".
[1] https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/mem/mtest06/mmap1.c
Link: http://lkml.kernel.org/r/5b3fdf19e2a5be460a384b936f5b56e13733f1b8.1551595137.git.jstancek@redhat.com
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Rafael Aquini <aquini@redhat.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 682aa8e1a6 ("writeback: implement unlocked_inode_to_wb
transaction and use it for stat updates") refers to
inode_switch_wb_work_fn() which never got merged.
Switch the comments to inode_switch_wbs_work_fn().
Link: http://lkml.kernel.org/r/20190305004617.142590-1-gthelen@google.com
Fixes: 682aa8e1a6 ("writeback: implement unlocked_inode_to_wb transaction and use it for stat updates")
Signed-off-by: Greg Thelen <gthelen@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
