Jiawen Wu says:
====================
Fix IRQ vectors
The interrupt vector order was adjusted by [1]commit 937d46ecc5 ("net:
wangxun: add ethtool_ops for channel number") in Linux-6.8. Because at
that time, the MISC interrupt acts as the parent interrupt in the GPIO
IRQ chip. When the number of Rx/Tx ring changes, the last MISC
interrupt must be reallocated. Then the GPIO interrupt controller would
be corrupted. So the initial plan was to adjust the sequence of the
interrupt vectors, let MISC interrupt to be the first one and do not
free it.
Later, irq_domain was introduced in [2]commit aefd013624 ("net: txgbe:
use irq_domain for interrupt controller") to avoid this problem.
However, the vector sequence adjustment was not reverted. So there is
still one problem that has been left unresolved.
Due to hardware limitations of NGBE, queue IRQs can only be requested
on vector 0 to 7. When the number of queues is set to the maximum 8,
the PCI IRQ vectors are allocated from 0 to 8. The vector 0 is used by
MISC interrupt, and althrough the vector 8 is used by queue interrupt,
it is unable to receive packets. This will cause some packets to be
dropped when RSS is enabled and they are assigned to queue 8.
This patch set fix the above problems.
[1] https://git.kernel.org/netdev/net-next/c/937d46ecc5f9
[2] https://git.kernel.org/netdev/net-next/c/aefd013624a1
====================
Link: https://patch.msgid.link/20250701063030.59340-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For NGBE devices, the queue number is limited to be 1 when SRIOV is
enabled. In this case, IRQ vector[0] is used for MISC and vector[1] is
used for queue, based on the previous patches. But for the hardware
design, the IRQ vector[1] must be allocated for use by the VF[6] when
the number of VFs is 7. So the IRQ vector[0] should be shared for PF
MISC and QUEUE interrupts.
+-----------+----------------------+
| Vector | Assigned To |
+-----------+----------------------+
| Vector 0 | PF MISC and QUEUE |
| Vector 1 | VF 6 |
| Vector 2 | VF 5 |
| Vector 3 | VF 4 |
| Vector 4 | VF 3 |
| Vector 5 | VF 2 |
| Vector 6 | VF 1 |
| Vector 7 | VF 0 |
+-----------+----------------------+
Minimize code modifications, only adjust the IRQ vector number for this
case.
Fixes: 877253d2cb ("net: ngbe: add sriov function support")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20250701063030.59340-4-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Due to hardware limitations of NGBE, queue IRQs can only be requested
on vector 0 to 7. When the number of queues is set to the maximum 8,
the PCI IRQ vectors are allocated from 0 to 8. The vector 0 is used by
MISC interrupt, and althrough the vector 8 is used by queue interrupt,
it is unable to receive packets. This will cause some packets to be
dropped when RSS is enabled and they are assigned to queue 8.
So revert the adjustment of the MISC IRQ location, to make it be the
last one in IRQ vectors.
Fixes: 937d46ecc5 ("net: wangxun: add ethtool_ops for channel number")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20250701063030.59340-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move the creating of irq_domain for MISC IRQ from .probe to .ndo_open,
and free it in .ndo_stop, to maintain consistency with the queue IRQs.
This it for subsequent adjustments to the IRQ vectors.
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250701063030.59340-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Laurent Vivier says:
====================
virtio: Fixes for TX ring sizing and resize error reporting
This patch series contains two fixes and a cleanup for the virtio subsystem.
The first patch fixes an error reporting bug in virtio_ring's
virtqueue_resize() function. Previously, errors from internal resize
helpers could be masked if the subsequent re-enabling of the virtqueue
succeeded. This patch restores the correct error propagation, ensuring that
callers of virtqueue_resize() are properly informed of underlying resize
failures.
The second patch does a cleanup of the use of '2+MAX_SKB_FRAGS'
The third patch addresses a reliability issue in virtio_net where the TX
ring size could be configured too small, potentially leading to
persistently stopped queues and degraded performance. It enforces a
minimum TX ring size to ensure there's always enough space for at least one
maximally-fragmented packet plus an additional slot.
====================
Link: https://patch.msgid.link/20250521092236.661410-1-lvivier@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The `tx_may_stop()` logic stops TX queues if free descriptors
(`sq->vq->num_free`) fall below the threshold of (`MAX_SKB_FRAGS` + 2).
If the total ring size (`ring_num`) is not strictly greater than this
value, queues can become persistently stopped or stop after minimal
use, severely degrading performance.
A single sk_buff transmission typically requires descriptors for:
- The virtio_net_hdr (1 descriptor)
- The sk_buff's linear data (head) (1 descriptor)
- Paged fragments (up to MAX_SKB_FRAGS descriptors)
This patch enforces that the TX ring size ('ring_num') must be strictly
greater than (MAX_SKB_FRAGS + 2). This ensures that the ring is
always large enough to hold at least one maximally-fragmented packet
plus at least one additional slot.
Reported-by: Lei Yang <leiyang@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-4-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Improve consistency by using everywhere it is needed
'MAX_SKB_FRAGS + 2' rather than '2+MAX_SKB_FRAGS' or
'2 + MAX_SKB_FRAGS'.
No functional change.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-3-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The virtqueue_resize() function was not correctly propagating error codes
from its internal resize helper functions, specifically
virtqueue_resize_packet() and virtqueue_resize_split(). If these helpers
returned an error, but the subsequent call to virtqueue_enable_after_reset()
succeeded, the original error from the resize operation would be masked.
Consequently, virtqueue_resize() could incorrectly report success to its
caller despite an underlying resize failure.
This change restores the original code behavior:
if (vdev->config->enable_vq_after_reset(_vq))
return -EBUSY;
return err;
Fix: commit ad48d53b5b ("virtio_ring: separate the logic of reset/enable from virtqueue_resize")
Cc: xuanzhuo@linux.alibaba.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-2-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When calling buf_to_xdp, the len argument is the frame data's length
without virtio header's length (vi->hdr_len). We check that len with
xsk_pool_get_rx_frame_size() + vi->hdr_len
to ensure the provided len does not larger than the allocated chunk
size. The additional vi->hdr_len is because in virtnet_add_recvbuf_xsk,
we use part of XDP_PACKET_HEADROOM for virtio header and ask the vhost
to start placing data from
hard_start + XDP_PACKET_HEADROOM - vi->hdr_len
not
hard_start + XDP_PACKET_HEADROOM
But the first buffer has virtio_header, so the maximum frame's length in
the first buffer can only be
xsk_pool_get_rx_frame_size()
not
xsk_pool_get_rx_frame_size() + vi->hdr_len
like in the current check.
This commit adds an additional argument to buf_to_xdp differentiate
between the first buffer and other ones to correctly calculate the maximum
frame's length.
Cc: stable@vger.kernel.org
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Fixes: a4e7ba7027 ("virtio_net: xsk: rx: support recv small mode")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250630151315.86722-2-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Bui Quang Minh says:
====================
virtio-net: fixes for mergeable XDP receive path
This series contains fixes for XDP receive path in virtio-net
- Patch 1: add a missing check for the received data length with our
allocated buffer size in mergeable mode.
- Patch 2: remove a redundant truesize check with PAGE_SIZE in mergeable
mode
- Patch 3: make the current repeated code use the check_mergeable_len to
check for received data length in mergeable mode
====================
Link: https://patch.msgid.link/20250630144212.48471-1-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace the current repeated code to check received length in mergeable
mode with the new check_mergeable_len helper.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250630144212.48471-4-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The truesize is guaranteed not to exceed PAGE_SIZE in
get_mergeable_buf_len(). It is saved in mergeable context, which is not
changeable by the host side, so the check in receive path is quite
redundant.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250630144212.48471-3-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In xdp_linearize_page, when reading the following buffers from the ring,
we forget to check the received length with the true allocate size. This
can lead to an out-of-bound read. This commit adds that missing check.
Cc: <stable@vger.kernel.org>
Fixes: 4941d472bf ("virtio-net: do not reset during XDP set")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250630144212.48471-2-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-07-01 (idpf, igc)
For idpf:
Michal returns 0 for key size when RSS is not supported.
Ahmed changes control queue to a spinlock due to sleeping calls.
For igc:
Vitaly disables L1.2 PCI-E link substate on I226 devices to resolve
performance issues.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: disable L1.2 PCI-E link substate to avoid performance issue
idpf: convert control queue mutex to a spinlock
idpf: return 0 size for RSS key if not supported
====================
Link: https://patch.msgid.link/20250701164317.2983952-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
udp_v4_early_demux now returns drop reasons as it either returns 0 or
ip_mc_validate_source, which returns itself a drop reason. However its
use was not converted in ip_rcv_finish_core and the drop reason is
ignored, leading to potentially skipping increasing LINUX_MIB_IPRPFILTER
if the drop reason is SKB_DROP_REASON_IP_RPFILTER.
This is a fix and we're not converting udp_v4_early_demux to explicitly
return a drop reason to ease backports; this can be done as a follow-up.
Fixes: d46f827016 ("net: ip: make ip_mc_validate_source() return drop reason")
Cc: Menglong Dong <menglong8.dong@gmail.com>
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20250701074935.144134-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting "ethtool -L eth0 combined 1", the number of RX/TX queue is
changed to be 1. RSS is disabled at this moment, and the indices of FDIR
have not be changed in wx_set_rss_queues(). So the combined count still
shows the previous value. This issue was introduced when supporting
FDIR. Fix it for those devices that support FDIR.
Fixes: 34744a7749 ("net: txgbe: add FDIR info to ethtool ops")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/A5C8FE56D6C04608+20250701070625.73680-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The link status is latched low so that momentary link drops
can be detected. Always double-reading the status defeats this
design feature. Only double read if link was already down
This prevents unnecessary duplicate readings of the link status.
Fixes: 4f3b20bfbb ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250701065016.4140707-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Certain classful qdiscs may invoke their classes' dequeue handler on an
enqueue operation. This may unexpectedly empty the child qdisc and thus
make an in-flight class passive via qlen_notify(). Most qdiscs do not
expect such behaviour at this point in time and may re-activate the
class eventually anyways which will lead to a use-after-free.
The referenced fix commit attempted to fix this behavior for the HFSC
case by moving the backlog accounting around, though this turned out to
be incomplete since the parent's parent may run into the issue too.
The following reproducer demonstrates this use-after-free:
tc qdisc add dev lo root handle 1: drr
tc filter add dev lo parent 1: basic classid 1:1
tc class add dev lo parent 1: classid 1:1 drr
tc qdisc add dev lo parent 1:1 handle 2: hfsc def 1
tc class add dev lo parent 2: classid 2:1 hfsc rt m1 8 d 1 m2 0
tc qdisc add dev lo parent 2:1 handle 3: netem
tc qdisc add dev lo parent 3:1 handle 4: blackhole
echo 1 | socat -u STDIN UDP4-DATAGRAM:127.0.0.1:8888
tc class delete dev lo classid 1:1
echo 1 | socat -u STDIN UDP4-DATAGRAM:127.0.0.1:8888
Since backlog accounting issues leading to a use-after-frees on stale
class pointers is a recurring pattern at this point, this patch takes
a different approach. Instead of trying to fix the accounting, the patch
ensures that qdisc_tree_reduce_backlog always calls qlen_notify when
the child qdisc is empty. This solves the problem because deletion of
qdiscs always involves a call to qdisc_reset() and / or
qdisc_purge_queue() which ultimately resets its qlen to 0 thus causing
the following qdisc_tree_reduce_backlog() to report to the parent. Note
that this may call qlen_notify on passive classes multiple times. This
is not a problem after the recent patch series that made all the
classful qdiscs qlen_notify() handlers idempotent.
Fixes: 3f98113810 ("sch_hfsc: Fix qlen accounting bug when using peek in hfsc_enqueue()")
Signed-off-by: Lion Ackermann <nnamrec@gmail.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/d912cbd7-193b-4269-9857-525bee8bbb6a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dma_map_XXX() functions return values DMA_MAPPING_ERROR as error values
which is often ~0. The error value should be tested with
dma_mapping_error().
This patch creates a new function in niu_ops to test if the mapping
failed. The test is fixed in niu_rbr_add_page(), added in
niu_start_xmit() and the successfully mapped pages are unmaped upon error.
Fixes: ec2deec1f3 ("niu: Fix to check for dma mapping errors.")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two bugs in rose_rt_device_down() that can cause
use-after-free:
1. The loop bound `t->count` is modified within the loop, which can
cause the loop to terminate early and miss some entries.
2. When removing an entry from the neighbour array, the subsequent entries
are moved up to fill the gap, but the loop index `i` is still
incremented, causing the next entry to be skipped.
For example, if a node has three neighbours (A, A, B) with count=3 and A
is being removed, the second A is not checked.
i=0: (A, A, B) -> (A, B) with count=2
^ checked
i=1: (A, B) -> (A, B) with count=2
^ checked (B, not A!)
i=2: (doesn't occur because i < count is false)
This leaves the second A in the array with count=2, but the rose_neigh
structure has been freed. Code that accesses these entries assumes that
the first `count` entries are valid pointers, causing a use-after-free
when it accesses the dangling pointer.
Fix both issues by iterating over the array in reverse order with a fixed
loop bound. This ensures that all entries are examined and that the removal
of an entry doesn't affect subsequent iterations.
Reported-by: syzbot+e04e2c007ba2c80476cb@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=e04e2c007ba2c80476cb
Tested-by: syzbot+e04e2c007ba2c80476cb@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250629030833.6680-1-enjuk@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The comparison in enic_change_mtu() incorrectly used the current
netdev->mtu instead of the new new_mtu value when warning about
an MTU exceeding the port MTU. This could suppress valid warnings
or issue incorrect ones.
Fix the condition and log to properly reflect the new_mtu.
Fixes: ab123fe071 ("enic: handle mtu change for vf properly")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Acked-by: John Daley <johndale@cisco.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250628145612.476096-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the Clause 37 Auto-Negotiation implementation to properly align
with the PCS hardware specifications:
- Fix incorrect bit settings in Link Status and Link Duplex fields
- Implement missing sequence steps 2 and 7
These changes ensure CL37 auto-negotiation protocol follows the exact
sequence patterns as specified in the hardware databook.
Fixes: 1bf40ada62 ("amd-xgbe: Add support for clause 37 auto-negotiation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250630192636.3838291-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch complains that the error message isn't set in the caller:
lib/test_objagg.c:923 test_hints_case2()
error: uninitialized symbol 'errmsg'.
This static checker warning only showed up after a recent refactoring
but the bug dates back to when the code was originally added. This
likely doesn't affect anything in real life.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202506281403.DsuyHFTZ-lkp@intel.com/
Fixes: 0a020d416d ("lib: introduce initial implementation of object aggregation manager")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/8548f423-2e3b-4bb7-b816-5041de2762aa@sabinyo.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I226 devices advertise support for the PCI-E link L1.2 substate. However,
due to a hardware limitation, the exit latency from this low-power state
is longer than the packet buffer can tolerate under high traffic
conditions. This can lead to packet loss and degraded performance.
To mitigate this, disable the L1.2 substate. The increased power draw
between L1.1 and L1.2 is insignificant.
Fixes: 4354621173 ("igc: Add new device ID's")
Link: https://lore.kernel.org/intel-wired-lan/15248b4f-3271-42dd-8e35-02bfc92b25e1@intel.com
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
- MGMT: set_mesh: update LE scan interval and window
- MGMT: mesh_send: check instances prior disabling advertising
- hci_sync: revert some mesh modifications
- hci_sync: Set extended advertising data synchronously
- hci_sync: Prevent unintended pause by checking if advertising is active
-----BEGIN PGP SIGNATURE-----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=QBPI
-----END PGP SIGNATURE-----
Merge tag 'for-net-2025-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- MGMT: set_mesh: update LE scan interval and window
- MGMT: mesh_send: check instances prior disabling advertising
- hci_sync: revert some mesh modifications
- hci_sync: Set extended advertising data synchronously
- hci_sync: Prevent unintended pause by checking if advertising is active
* tag 'for-net-2025-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: HCI: Set extended advertising data synchronously
Bluetooth: MGMT: mesh_send: check instances prior disabling advertising
Bluetooth: MGMT: set_mesh: update LE scan interval and window
Bluetooth: hci_sync: revert some mesh modifications
Bluetooth: Prevent unintended pause by checking if advertising is active
====================
Link: https://patch.msgid.link/20250627181601.520435-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d53320aeef ("dt-bindings: net: Rename
renesas,r9a09g057-gbeth.yaml") renames the net devicetree binding
renesas,r9a09g057-gbeth.yaml to renesas,rzv2h-gbeth.yaml, but misses to
adjust the file entry in the RENESAS RZ/V2H(P) DWMAC GBETH GLUE LAYER
DRIVER section in MAINTAINERS.
Adjust the file entry after this file renaming.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20250627134453.51780-1-lukas.bulwahn@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a occasional problem that ping is failed between AML devices.
That is because the manual enablement of the security Tx path on the
hardware is missing, no matter what its previous state was.
Fixes: 6f8b4c01a8 ("net: txgbe: Implement PHYLINK for AML 25G/10G devices")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/5BDFB14C57D1C42A+20250626085153.86122-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I have been working on mlx5 related code for several years,
contributing features, code reviews, and occasional maintainer tasks
when needed. This patch makes my maintainer role official.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://patch.msgid.link/20250627014252.1262592-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver registered xdp_rxq_info structures via xdp_rxq_info_reg()
but failed to properly unregister them in error paths and during
removal.
Fixes: d678be1dc1 ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Fushuai Wang <wangfushuai@baidu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20250626133003.80136-1-wangfushuai@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The `dma_map_XXX()` functions can fail and must be checked using
`dma_mapping_error()`. This patch adds proper error handling for all
DMA mapping calls.
In `atl1_alloc_rx_buffers()`, if DMA mapping fails, the buffer is
deallocated and marked accordingly.
In `atl1_tx_map()`, previously mapped buffers are unmapped and the
packet is dropped on failure.
If `atl1_xmit_frame()` drops the packet, increment the tx_error counter.
Fixes: f3cc28c797 ("Add Attansic L1 ethernet driver.")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Link: https://patch.msgid.link/20250625141629.114984-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To enable TLS ulp socket needs to be in established state.
This was added in commit d91c3e17f7 ("net/tls: Only attach
to sockets in ESTABLISHED state"), in 2018.
Signed-off-by: Ulrich Weber <ulrich.weber@gmail.com>
Link: https://patch.msgid.link/20250626145618.15464-1-ulrich.weber@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
"Co-posting selftests" belongs in the "netdev patch review" section,
same as "co-posting changes to user space components". It was
erroneously added as its own section.
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://patch.msgid.link/20250626182055.4161905-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to changes of my responsibilities within IBM i
can no longer act as maintainer for smc.
As a result of the co-operation with Alibaba over
the last years we decided to, once more, give them
more responsibility for smc by appointing
D. Wythe <alibuda@linux.alibaba.com> and
Dust Li <dust.li@linux.alibaba.com>
as maintainers as well.
Within IBM Sidraya Jayagond <sidraya@linux.ibm.com>
and Mahanta Jambigi <mjambigi@linux.ibm.com>
are going to take over the maintainership for smc.
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://patch.msgid.link/20250626051653.4259-1-jaka@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, for controllers with extended advertising, the advertising
data is set in the asynchronous response handler for extended
adverstising params. As most advertising settings are performed in a
synchronous context, the (asynchronous) setting of the advertising data
is done too late (after enabling the advertising).
Move setting of adverstising data from asynchronous response handler
into synchronous context to fix ordering of HCI commands.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: a0fb3726ba ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Cc: stable@vger.kernel.org
v2: https://lore.kernel.org/linux-bluetooth/20250626115209.17839-1-ceggers@arri.de/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The unconditional call of hci_disable_advertising_sync() in
mesh_send_done_sync() also disables other LE advertisings (non mesh
related).
I am not sure whether this call is required at all, but checking the
adv_instances list (like done at other places) seems to solve the
problem.
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
According to the message of commit b338d91703 ("Bluetooth: Implement
support for Mesh"), MGMT_OP_SET_MESH_RECEIVER should set the passive scan
parameters. Currently the scan interval and window parameters are
silently ignored, although user space (bluetooth-meshd) expects that
they can be used [1]
[1] https://git.kernel.org/pub/scm/bluetooth/bluez.git/tree/mesh/mesh-io-mgmt.c#n344
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts minor parts of the changes made in commit b338d91703
("Bluetooth: Implement support for Mesh"). It looks like these changes
were only made for development purposes but shouldn't have been part of
the commit.
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
'rx_ring->size' means the count of ring descriptors multiplied by the
size of one descriptor. When increasing the count of ring descriptors,
it may exceed the limit of pool size.
[ 864.209610] page_pool_create_percpu() gave up with errno -7
[ 864.209613] txgbe 0000:11:00.0: Page pool creation failed: -7
Fix to set the pool_size to the count of ring descriptors.
Fixes: 850b971110 ("net: libwx: Allocate Rx and Tx resources")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/434C72BFB40E350A+20250625023924.21821-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The length in the pseudo header should be the length of the L3 payload
AKA the L4 header+payload. The selftest code builds the packet from
the lower layers up, so all the headers are pushed already when it
constructs L4. We need to subtract the lower layer headers from skb->len.
Fixes: 3e1e58d64c ("net: add generic selftest support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250624183258.3377740-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=Buaz
-----END PGP SIGNATURE-----
Merge tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Pull bpf fixes from Alexei Starovoitov:
- Fix use-after-free in libbpf when map is resized (Adin Scannell)
- Fix verifier assumptions about 2nd argument of bpf_sysctl_get_name
(Jerome Marchand)
- Fix verifier assumption of nullness of d_inode in dentry (Song Liu)
- Fix global starvation of LRU map (Willem de Bruijn)
- Fix potential NULL dereference in btf_dump__free (Yuan Chen)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: adapt one more case in test_lru_map to the new target_free
libbpf: Fix possible use-after-free for externs
selftests/bpf: Convert test_sysctl to prog_tests
bpf: Specify access type of bpf_sysctl_get_name args
libbpf: Fix null pointer dereference in btf_dump__free on allocation failure
bpf: Adjust free target to avoid global starvation of LRU map
bpf: Mark dentry->d_inode as trusted_or_null
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCaFx0bQAKCRBZ7Krx/gZQ
63yTAQC4NS7qopT8BQGn3aM+t8YjYo36BTeSRcSy4hVEAFrEJAD/WyW5Dcy1lWZR
S8g8rqRimsCepwxqTinYJlS7H8S56ws=
=CmGc
-----END PGP SIGNATURE-----
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull mount fixes from Al Viro:
"Several mount-related fixes"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
userns and mnt_idmap leak in open_tree_attr(2)
attach_recursive_mnt(): do not lock the covering tree when sliding something under it
replace collect_mounts()/drop_collected_mounts() with a safer variant
Jakub Kicinski says:
====================
netlink: specs: enforce strict naming of properties
I got annoyed once again by the name properties in the ethtool spec
which use underscore instead of dash. I previously assumed that there
is a lot of such properties in the specs so fixing them now would
be near impossible. On a closer look, however, I only found 22
(rough grep suggests we have ~4.8k names in the specs, so bad ones
are just 0.46%).
Add a regex to the JSON schema to enforce the naming, fix the few
bad names. I was hoping we could start enforcing this from newer
families, but there's no correlation between the protocol and the
number of errors. If anything classic netlink has more recently
added specs so it has fewer errors.
The regex is just for name properties which will end up visible
to the user (in Python or YNL CLI). I left the c-name properties
alone, those don't matter as much. C codegen rewrites them, anyway.
I'm not updating the spec for genetlink-c. Looks like it has no
users, new families use genetlink, all old ones need genetlink-legacy.
If these patches are merged I will remove genetlink-c completely
in net-next.
====================
Link: https://patch.msgid.link/20250624211002.3475021-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a regexp to make sure all names which may end up being visible
to the user consist of lower case characters, numbers and dashes.
Underscores keep sneaking into the specs, which is not visible
in the C code but makes the Python and alike inconsistent.
Note that starting with a number is okay, as in C the full
name will include the family name.
For legacy families we can't enforce the naming in the family
name or the multicast group names, as these are part of the
binary uAPI of the kernel.
For classic netlink we need to allow capital letters in names
of struct members. TC has some structs with capitalized members.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-11-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: a1bcfde836 ("doc/netlink/specs: Add a spec for tc")
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-10-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
