commit 1e66cded33 upstream.
This is legitimate but because we don't clear the drv->state pointer in the
unregister code causes a bogus BUG().
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42880
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a7b83f86 upstream.
tty_unlock is used on all other exits from the function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af6d17cdc8 upstream.
This driver anticipates pch_uart_verify_port() is not called
during installation.
However, actually pch_uart_verify_port() is called during
installation.
As a result, memory access violation occurs like below.
0. initial value: use_dma=0
1. starup()
- dma channel is not allocated because use_dma=0
2. pch_uart_verify_port()
- Set use_dma=1
3. UART processing acts DMA mode because use_dma=1
- memory access violation occurs!
This patch fixes the issue.
Solution:
Whenever pch_uart_verify_port() is called and then
dma channel is not allocated, the channel should be allocated.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a6fbc9a88 upstream.
Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result
of call disable_irq from ISR. synchronize_irq waits for end of interrupt
and goes to infinite loop. This patch fix this problem.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64d91cfaad upstream.
Currently, ".setup" function is not set.
As a result, when detecting our IOH's uart device without pch_uart, kernel panic
occurs at the following of pciserial_init_ports().
for (i = 0; i < nr_ports; i++) {
if (quirk->setup(priv, board, &serial_port, i))
break;
So, this patch adds the ".setup" function.
We can use pci_default_setup because our IOH's uart is compatible with 16550.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c4b47d243 upstream.
Currently, PCIe bus number is set as fixed value "2".
However, PCIe bus number is not always "2".
This patch sets bus number using probe() parameter.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3d8b76f61 upstream.
Commit 360f748b204275229f8398cb2f9f53955db1503b
"serial: PL011: clear pending interrupts"
attempts to clear interrupts by writing to a
yet-unassigned memory address. This fixes the issue.
The breaking patch is marked for stable so should be
carried along with the other patch.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@fluxnic.net>
Reported-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b96fbacda upstream.
Chanho Min reported that when the boot loader transfers
control to the kernel, there may be pending interrupts
causing the UART to lock up in an eternal loop trying to
pick tokens from the FIFO (since the RX interrupt flag
indicates there are tokens) while in practice there are
no tokens - in fact there is only a pending IRQ flag.
This patch address the issue with a combination of two
patches suggested by Russell King that clears and mask
all interrupts at probe() and clears any pending error
and RX interrupts at port startup time.
We suspect the spurious interrupts are a side-effect of
switching the UART from FIFO to non-FIFO mode.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Reported-by: Chanho Min <chanho0207@gmail.com>
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jong-Sung Kim <neidhard.kim@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acede70d65 upstream.
Follow altera_jtag_uart. This fixes a crash if there is a mistake in the DTS.
Signed-off-by: Yuriy Kozlov <ykozlov@ptcusa.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49d4bcaddc upstream.
When DMA is enabled, sh-sci transfer begins with
uart_start()
sci_start_tx()
if (cookie_tx < 0) schedule_work()
Then, starts DMA when wq scheduled, -- (A)
process_one_work()
work_fn_rx()
cookie_tx = desc->submit_tx()
And finishes when DMA transfer ends, -- (B)
sci_dma_tx_complete()
async_tx_ack()
cookie_tx = -EINVAL
(possible another schedule_work())
This A to B sequence is not reentrant, since controlling variables
(for example, cookie_tx above) are not queues nor lists. So, they
must be invoked as A B A B..., otherwise results in kernel crash.
To ensure the sequence, sci_start_tx() seems to test if cookie_tx < 0
(represents "not used") to call schedule_work().
But cookie_tx will not be set (to a cookie, also means "used") until
in the middle of work queue scheduled function work_fn_tx().
This gap between the test and set allows the breakage of the sequence
under the very frequently call of uart_start().
Another gap between async_tx_ack() and another schedule_work() results
in the same issue, too.
This patch introduces a new condition "cookie_tx == 0" just to mark
it is "busy" and assign it within spin-locked region to fill the gaps.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a4c61b7ce upstream.
Bugzilla 40012: PIO_UNIMAP bug: error updating Unicode-to-font map
https://bugzilla.kernel.org/show_bug.cgi?id=40012
The unicode font map for the virtual console is a 32x32x64 table which
allocates rows dynamically as entries are added. The unicode value
increases sequentially and should count all entries even in empty
rows. The defect is when copying the unicode font map in con_set_unimap(),
the unicode value is not incremented properly. The wrong unicode value
is entered in the new font map.
Signed-off-by: Liz Clark <liz.clark@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58112dfbfe upstream.
This is supposed to be doing a shift before the comparison instead of
just doing a bitwise AND directly. The current code means the start()
just returns without doing anything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbcb834605 upstream.
KDFONTOP(GET) currently fails with EIO when being run in a 32bit userland
with a 64bit kernel if the font width is not 8.
This is because of the setting of the KD_FONT_FLAG_OLD flag, which makes
con_font_get return EIO in such case.
This flag should *not* be set for KDFONTOP, since it's actually the whole
point of this flag (see comment in con_font_set for instance).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arthur Taylor <art@ified.ca>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26aa38cafa upstream.
There was an error on the jsm driver that would cause it to be unable to
recover after a second error is detected.
At the first error, the device recovers properly:
[72521.485691] EEH: Detected PCI bus error on device 0003:02:00.0
[72521.485695] EEH: This PCI device has failed 1 times in the last hour:
...
[72532.035693] ttyn3 at MMIO 0x0 (irq = 49) is a jsm
[72532.105689] jsm: Port 3 added
However, at the second error, it cascades until EEH disables the device:
[72631.229549] Call Trace:
...
[72641.725687] jsm: Port 3 added
[72641.725695] EEH: Detected PCI bus error on device 0003:02:00.0
[72641.725698] EEH: This PCI device has failed 3 times in the last hour:
It was caused because the PCI state was not being saved after the first
restore. Therefore, at the second recovery the PCI state would not be
restored.
Signed-off-by: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef605fdb33 upstream.
Protect against pl011_console_write() and the interrupt for
the console UART running concurrently on different CPUs.
Otherwise the console_write could spin for a long time
waiting for the UART to become not busy, while the other
CPU continuously services UART interrupts and keeps the
UART busy.
The checks for sysrq and oops_in_progress are taken
from 8250.c.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Bibek Basu <bibek.basu@stericsson.com>
Reviewed-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eee50af5b upstream.
Commit 74c2107759 (serial: Use block_til_ready helper) and its fixup
3f582b8c11 (serial: fix termios settings in open) introduced a
regression on UV systems. The serial eventually freezes while being
used. It's completely unpredictable and sometimes needs a heap of
traffic to happen first.
To reproduce this, yast installation was used as it turned out to be
pretty reliable in reproducing. Especially during installation process
where one doesn't have an SSH daemon running. And no monitor as the HW
is completely headless. So this was fun to find. Given the machine
doesn't boot on vanilla before 2.6.36 final. (And the commits above
are older.)
Unless there is some bad race in the code, the hardware seems to be
pretty broken. Otherwise pure MSR read should not cause such a bug,
or?
So to prevent the bug, revert to the old behavior. I.e. read modem
status only if we really have to -- for non-CLOCAL set serials.
Non-CLOCAL works on this hardware OK, I tried. See? I don't.
And document that shit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
References: https://lkml.org/lkml/2011/12/6/573
References: https://bugzilla.novell.com/show_bug.cgi?id=718518
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbf1115d3f upstream.
Patch to fix a spinlock lockup in the driver that sometimes happens when the
tasklet starts.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Dave Bender <codehero@gmail.com>
Tested-by: Dave Bender <codehero@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0c73c08ec7 upstream.
For /dev/console case, we do not kill all ldisc users. It's due to
redirected_tty_write test in __tty_hangup. In that case there still
might be a process waiting e.g. in n_tty_read for input.
We wait for such processes to disappear. The problem is that we use a
timeout. After this timeout, we continue closing the ldisc and start
freeing tty resources. It obviously leads to crashes when the other
process is woken.
So to fix this, we wait infinitely before reiniting the ldisc. (The
tiocsetd remains untouched -- times out after 5s.)
This is nicely reproducible with this run from shell:
exec 0<>/dev/console 1<>/dev/console 2<>/dev/console
and stopping a getty like:
systemctl stop serial-getty@ttyS0.service
The crash proper may be produced only under load or with constified
timing the same as for 92f6fa09b.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Dmitriy Matrosov <sgf.dma@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 300420722e upstream.
It is the only place where reinit is called from. And we really need
to wait for the old ldisc to go once. Actually this is the place where
the waiting originally was (before removed and re-added later).
This will make the fix in the following patch easier to implement.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Dmitriy Matrosov <sgf.dma@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit df92d0561d upstream.
To fix a nasty bug in ldisc hup vs. reinit we need to wait infinitely
long for ldisc to be gone. So here we add a parameter to
tty_ldisc_wait_idle to allow that.
This is only a preparation for the real fix which is done in the
following patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Dmitriy Matrosov <sgf.dma@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c2a3e84f95 upstream.
Reading from the DCC grabs a character from the buffer and
clears the status bit. Since this is a context-changing
operation, instructions following the character read that rely on
the status bit being accurate need to be synchronized with an
ISB.
In this case, the status bit check needs to execute after the
character read otherwise we run the risk of reading the character
and checking the status bit before the read can clear the status
bit in the first place. When this happens, the user will see the
same character they typed twice, instead of once.
Add an ISB after the read and the write, so that the status check
is synchronized with the read/write operations.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 90f04c2926 upstream.
Changing UART mode PIO->DMA->PIO->DMA like below, pch_uart driver can't get
DMA channel resource.
setserial /dev/ttyPCH0 ^low_latency
setserial /dev/ttyPCH0 low_latency
CAUSE:
Changing mode using setserial command, ".startup" function which gets DMA
channel is called before ".verify_port" function which sets
dma-flag(use_dma/use_dma_flag) as 1.
PIO->DMA
.startup: Since dma-flag is 0, DMA channel is not requested.
.verify_port: dma-flag is set as 1.
.shutdown: N/A
DMA->PIO
.startup: Since dma-flag is 1, DMA channel is requested.
.verify_port: dma-flag is set as 0.
.shutdown: Since dma-flag is 0, DMA channel is not released.
This means DMA channel resource leak occurs.
Next time, this driver can't get DMA channel resource forever.
MODIFICATION:
Currently, when release DMA channel resource, this driver checks dma-flag.
However, this specification occurs the above issue.
This driver must check whether dma_request_channel is executed or not.
The values are saved in private data variable "chan_tx/chan_tx".
These variables mean if the value is NULL, DMA channel is not requested,
if not NULL, DMA channel is requested.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a1d7cfe29f upstream.
Using hardware flow control,
currently, register of the control-bit(AFE) is not set.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9d898966c4 upstream.
jsm uses a write queue that copies from uart_core circular buffer. This
copying however has some bugs, like not wrapping the head counter. Since
this write queue is also a circular buffer, the consumer function is
ready to use the uart_core circular buffer directly.
This buggy copying function was making some bytes be dropped when
transmitting to a raw tty, doing something like this.
[root@hostname ~]$ cat /dev/ttyn1 > cascardo/dump &
[1] 2658
[root@hostname ~]$ cat /proc/tty/drivers > /dev/ttyn0
[root@hostname ~]$ cat /proc/tty/drivers
/dev/tty /dev/tty 5 0 system:/dev/tty
/dev/console /dev/console 5 1 system:console
/dev/ptmx /dev/ptmx 5 2 system
/dev/vc/0 /dev/vc/0 4 0 system:vtmaster
jsm /dev/ttyn 250 0-31 serial
serial /dev/ttyS 4 64-95 serial
hvc /dev/hvc 229 0-7 system
pty_slave /dev/pts 136 0-1048575 pty:slave
pty_master /dev/ptm 128 0-1048575 pty:master
unknown /dev/tty 4 1-63 console
[root@hostname ~]$ cat cascardo/dump
/dev/tty /dev/tty 5 0 system:/dev/tty
/dev/console /dev/console 5 1 system:console
/dev/ptmx /dev/ptmx 5 2 system
/dev/vc/0 /dev/vc/0 4 0 system:vtmaste[root@hostname ~]$
This patch drops the driver write queue entirely, using the circular
buffer from uart_core only.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 94abc56f4d upstream.
The following patch removed uart_change_pm() in uart_resume_port():
commit 5933a161ab
Author: Yin Kangkai <kangkai.yin@linux.intel.com>
serial-core: reset the console speed on resume
It will break the pxa serial driver when the system resumes from suspend mode
as it will try to set baud rate divider register in set_termios but with
clock off. The register value can not be set correctly on some platform if
the clock is disabled. The pxa driver will check the value and report the
following warning:
------------[ cut here ]------------
WARNING: at drivers/tty/serial/pxa.c:545 serial_pxa_set_termios+0x1dc/0x250()
Modules linked in:
[<c0281f30>] (unwind_backtrace+0x0/0xf0) from [<c029341c>] (warn_slowpath_common+0x4c/0x64)
[<c029341c>] (warn_slowpath_common+0x4c/0x64) from [<c029344c>] (warn_slowpath_null+0x18/0x1c)
[<c029344c>] (warn_slowpath_null+0x18/0x1c) from [<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250)
[<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250) from [<c044a840>] (uart_resume_port+0x128/0x2dc)
[<c044a840>] (uart_resume_port+0x128/0x2dc) from [<c044bbe0>] (serial_pxa_resume+0x18/0x24)
[<c044bbe0>] (serial_pxa_resume+0x18/0x24) from [<c0454d34>] (platform_pm_resume+0x40/0x4c)
[<c0454d34>] (platform_pm_resume+0x40/0x4c) from [<c0457ebc>] (pm_op+0x68/0xb4)
[<c0457ebc>] (pm_op+0x68/0xb4) from [<c0458368>] (device_resume+0xb0/0xec)
[<c0458368>] (device_resume+0xb0/0xec) from [<c04584c8>] (dpm_resume+0xe0/0x194)
[<c04584c8>] (dpm_resume+0xe0/0x194) from [<c0458588>] (dpm_resume_end+0xc/0x18)
[<c0458588>] (dpm_resume_end+0xc/0x18) from [<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac)
[<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac) from [<c02c5278>] (enter_state+0xac/0xdc)
[<c02c5278>] (enter_state+0xac/0xdc) from [<c02c48ec>] (state_store+0xa0/0xbc)
[<c02c48ec>] (state_store+0xa0/0xbc) from [<c0408f7c>] (kobj_attr_store+0x18/0x1c)
[<c0408f7c>] (kobj_attr_store+0x18/0x1c) from [<c034a6a4>] (sysfs_write_file+0x108/0x140)
[<c034a6a4>] (sysfs_write_file+0x108/0x140) from [<c02fb798>] (vfs_write+0xac/0x134)
[<c02fb798>] (vfs_write+0xac/0x134) from [<c02fb8cc>] (sys_write+0x3c/0x68)
[<c02fb8cc>] (sys_write+0x3c/0x68) from [<c027c700>] (ret_fast_syscall+0x0/0x2c)
---[ end trace 88289eceb4675b04 ]---
This patch fix the problem by adding the power on opertion back for uart
console when console_suspend_enabled is true.
Signed-off-by: Ning Jiang <ning.jiang@marvell.com>
Tested-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e44aabd649 upstream.
Errata E20: UART: Character Timeout interrupt remains set under certain
software conditions.
Implication: The software servicing the UART can be trapped in an infinite loop.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1177c0efc0 upstream.
Mistakenly, commit 64ba3dc314 (tty: never hold BTM while getting
tty_mutex) switched one fail path in ptmx_open to not free the newly
allocated tty.
Fix that by jumping to the appropriate place. And rename the labels so
that it's clear what is going on there.
Introduced-in: v2.6.36-rc2
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit fa90e1c935 upstream.
If tty_add_file fails at the point it is now, we have to revert all
the changes we did to the tty. It means either decrease all refcounts
if this was a tty reopen or delete the tty if it was newly allocated.
There was a try to fix this in v3.0-rc2 using tty_release in 0259894c7
(TTY: fix fail path in tty_open). But instead it introduced a NULL
dereference. It's because tty_release dereferences
filp->private_data, but that one is set even in our tty_add_file. And
when tty_add_file fails, it's still NULL/garbage. Hence tty_release
cannot be called there.
To circumvent the original leak (and the current NULL deref) we split
tty_add_file into two functions, making the latter non-failing. In
that case we may do the former early in open, where handling failures
is easy. The latter stays as it is now. So there is no change in
functionality.
The original bug (leak) was introduced by f573bd176 (tty: Remove
__GFP_NOFAIL from tty_add_file()). Thanks Dan for reporting this.
Later, we may split tty_release into more functions and call only some
of them in this fail path instead. (If at all possible.)
Introduced-in: v2.6.37-rc2
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c290f8358a upstream.
When tty_driver_lookup_tty fails in tty_open, we forget to drop a
reference to the tty driver. This was added by commit 4a2b5fddd5 (Move
tty lookup/reopen to caller).
Fix that by adding tty_driver_kref_put to the fail path.
I will refactor the code later. This is for the ease of backporting to
stable.
Introduced-in: v2.6.28-rc2
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 2f7861de11 upstream.
This patch fixes the following build error:
drivers/tty/serial/crisv10.c:4453: error: 'if_ser0' undeclared (first use in this function): 2 errors in 2 logs
v3.1-rc4/cris/cris-allmodconfig v3.1-rc4/cris/cris-allyesconfig
drivers/tty/serial/crisv10.c:4453: error: (Each undeclared identifier is reported only once: 2 errors in 2 logs
v3.1-rc4/cris/cris-allmodconfig v3.1-rc4/cris/cris-allyesconfig
drivers/tty/serial/crisv10.c:4453: error: for each function it appears in.): 2 errors in 2 logs
v3.1-rc4/cris/cris-allmodconfig v3.1-rc4/cris/cris-allyesconfig
"if_ser0" is a typo, it should be "if_serial_0".
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
