Create struct with bus operations, which will be used to extend bus
implementation features. Auxiliary functions ad5686_write() and
ad5686_read() are created and ad5686_probe() now receives an ops struct
pointer rather than individual read and write functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Review documentation comment header for ad5686_chip_info and ad5686_state.
Update variable names and description and remove unnecessary blank line
between comment and struct declaration.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Create ad5310_control_sync() and ad5683_control_sync() functions that
properly consume the mask definitions with FIELD_PREP(). This allows to
reuse a function that updates the control register with cached values,
without relying on confusing logic that depends on st->use_internal_vref,
which is initialized earlier in ad5686_probe() because it is also
applicable to the AD5686_REGMAP case, removing the need for the
has_external_vref. Powerdown masks initialization is simplified as
*_control_sync() masks outs any unused bits for the single-channel case.
The change cleans up ad5686_write_dac_powerdown() and ad5686_probe(),
organizing the code for feature extension, e.g. gain control support for
single-channel devices.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add ad5686_pd_field_set() and ad5686_pd_field_get() helpers to cleanup
powerdown mask control. Define AD5686_PD_* constants, e.g. AD5686_PD_MSK
to hold powerdown mask value for a single channel. AD5686_LDAC_PWRDN_*
macros are replaced by AD5686_PD_MODE_*, because they are unused and the
LDAC feature for async load of DAC channel values is not related to power
down control.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match table for the SPI device variants to be consistent with the
AD5696 I2C driver.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Split chip info table into separate structs and expose them to the spi
i2c drivers. That is the preferrable approach and allows for the drivers
to have knowledge of the device info before the common probe function gets
called. Those chip info structs may be shared by SPI and I2C driver
variants.
Channel declaration definitions are grouped according to channel count and
DECLARE_AD5693_CHANNELS() macro is renamed to DECLARE_AD5683_CHANNELS() to
match the regmap_type enum.
Use spi_get_device_match_data() and i2c_get_match_data() to get chip info
struct reference, passing it as parameter to the core probe function.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
AD5683_REGMAP and AD5693_REGMAP behave the same way in the common code,
and that is because they target single channel devices from the same
sub-family. There is no reason to separate them and it will make things
simpler when refactoring the chip info table.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Apply IWYU principle, replacing unused/generic headers for
specific/missing headers. The resulting include directive lists are sorted
accordingly.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The AD4880 chip ID was incorrectly set to 0x0750. According to the
datasheet, the product ID registers read 0x00 (PRODUCT_ID_H) and 0x59
(PRODUCT_ID_L), giving a combined chip ID of 0x0059. Fix the value to
match the actual hardware.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the Vishay VEML3328 RGB/IR light sensor communicating
via I2C (SMBus compatible).
Also add a new entry for said driver into Kconfig and Makefile.
Assisted-by: Gemini:3.1-Pro
Signed-off-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Vishay VEML3328 is an RGBCIR light sensor that shares similar
devicetree properties as other existing VEMLxxxx sensors in the
kernel.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Make the clearcpuid= boot parameter less prominent
and warn about its dangers & caveats (Borislav Petkov)
- Do not access the (new) PLATFORM_ID MSR when running as a guest
(Borislav Petkov)
- x86 ftrace: Relocate %rip-relative percpu refs in dynamic
trampolines, to fix crash when using such trampolines
(Alexis Lothoré)
- Fix x86-64 CFI build error (Peter Zijlstra)
- Revert FPU signal return magic number check optimization, because
it broke CRIU and gVisor in certain FPU configurations
(Andrei Vagin)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=4sLh
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2026-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Make the clearcpuid= boot parameter less prominent
and warn about its dangers & caveats (Borislav Petkov)
- Do not access the (new) PLATFORM_ID MSR when running
as a guest (Borislav Petkov)
- x86 ftrace: Relocate %rip-relative percpu refs in dynamic
trampolines, to fix crash when using such trampolines
(Alexis Lothoré)
- Fix x86-64 CFI build error (Peter Zijlstra)
- Revert FPU signal return magic number check optimization,
because it broke CRIU and gVisor in certain FPU configurations
(Andrei Vagin)
* tag 'x86-urgent-2026-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "x86/fpu: Refine and simplify the magic number check during signal return"
x86/kvm/vmx: Fix x86_64 CFI build
x86/ftrace: Relocate %rip-relative percpu refs in dynamic trampolines
x86/microcode: Do not access MSR_IA32_PLATFORM_ID when running as a guest
Documentation/arch/x86: Hide clearcpuid=
Two core changes, the only one of significance being the change to kick queues
in SDEV_CANCEL which had a small window for stuck requests. The major driver
fixes are the one to the FC transport class to widen the FPIN counter to
counter a theoretical (and privileged) fabric traffic injection attack and the
other is an iscsi fix where a malicious target could trick the kernel into an
output buffer overrun. Both the driver fixes were AI assisted.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCahxQ/RsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMiwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIX+HgD+Mqf+AKbV/EhPhKAfONeBaE0Q5e78KTyK
3e47Qxjs+mQBAKhWUwodLDS/WSm7Fbdj7tn/kuPSaH+R+JQltnPR4QPG
=BRJ7
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two core changes, the only one of significance being the change to
kick queues in SDEV_CANCEL which had a small window for stuck
requests.
The major driver fixes are the one to the FC transport class to widen
the FPIN counter to counter a theoretical (and privileged) fabric
traffic injection attack and the other is an iscsi fix where a
malicious target could trick the kernel into an output buffer overrun.
Both the driver fixes were AI assisted"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: iscsi: Validate CHAP_R length before base64 decode
scsi: target: iscsi: Bound iscsi_encode_text_output() appends to rsp_buf
scsi: target: iscsi: Fix CRC overread and double-free in iscsit_handle_text_cmd()
scsi: fcoe: Reject FIP descriptors with zero fip_dlen in CVL walker
scsi: scsi_transport_fc: Widen FPIN pname walker counter to u32
scsi: scsi_debug: Add missing newline in scsi_debug_device_reset()
scsi: megaraid_sas: Fix NULL pointer dereference on firmware duplicate completion
scsi: devinfo: Add BLIST_NO_RSOC for Promise VTrak E310f
scsi: core: Run queues for all non-SDEV_DEL devices from scsi_run_host_queues
davinci: fix fallback bus frequency on missing clock-frequency
virtio: mark device ready initially
-----BEGIN PGP SIGNATURE-----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=AcAd
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- davinci: fix fallback bus frequency on missing clock-frequency
- virtio: mark device ready initially
* tag 'i2c-for-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: virtio: mark device ready before registering the adapter
i2c: davinci: fix division by zero on missing clock-frequency
- updates to Elan I2C touchpad driver to handle a new IC type and to
validate size of supplied firmware to prevent OOB access
- updates to Xpad controller driver to recognize ASUS ROG RAIKIRI II and
"Nova 2 Lite" from GameSir controllers as well as a fix to prevent a
potential OOB access when handling "Share" button
- an update to Synaptics touchpad driver to use RMI mode for touchpad in
Thinkpad E490
- updates to Atmel MXT driver adding checks to prevent potential OOB
accesses
- a fix to IMS PCU driver to free correct amount of memory when
tearing it down
- a fixup to the recent change to Atlas buttons driver
- a small cleanup in fm801-fp for PCI IDs table initialisation
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCahvBFwAKCRBAj56VGEWX
nP7XAQDH9WIYBX7XEHSPInN6GH8GngWA/94v3b6UpBSL2UFdQQEAo1+WoyOGL/Dh
0U0g5CcvDwx9irF8qJBWX2a3DRNPngo=
=hDBA
-----END PGP SIGNATURE-----
Merge tag 'input-for-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- updates to Elan I2C touchpad driver to handle a new IC type and to
validate size of supplied firmware to prevent OOB access
- updates to Xpad controller driver to recognize ASUS ROG RAIKIRI II
and "Nova 2 Lite" from GameSir controllers as well as a fix to
prevent a potential OOB access when handling "Share" button
- an update to Synaptics touchpad driver to use RMI mode for touchpad
in Thinkpad E490
- updates to Atmel MXT driver adding checks to prevent potential OOB
accesses
- a fix to IMS PCU driver to free correct amount of memory when tearing
it down
- a fixup to the recent change to Atlas buttons driver
- a small cleanup in fm801-fp for PCI IDs table initialisation
* tag 'input-for-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-pcu - fix usb_free_coherent() size in ims_pcu_buffers_free()
Input: synaptics - add LEN2058 to SMBus passlist for ThinkPad E490
Input: atlas - check ACPI_COMPANION() against NULL
Input: atmel_mxt_ts - check mem_size before calculating config memory size
Input: atmel_mxt_ts - fix boundary check in mxt_prepare_cfg_mem
Input: fm801-gp - simplify initialisation of pci_device_id array
Input: xpad - add "Nova 2 Lite" from GameSir
Input: xpad - add support for ASUS ROG RAIKIRI II
Input: elan_i2c - validate firmware size before use
Input: xpad - fix out-of-bounds access for Share button
Input: usbtouchscreen - clamp NEXIO data_len/x_len to URB buffer size
Input: elan_i2c - increase device reset wait timeout after update FW
Input: elan_i2c - add ic type 0x19
Add RST documentation for the AD4691 family ADC driver covering
supported devices, IIO channels, operating modes, oversampling,
reference voltage, LDO supply, reset, GP pins, SPI offload support,
and buffer data format.
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add oversampling ratio (OSR) support for CNV burst mode. The accumulator
depth register (ACC_DEPTH_IN(0)) is programmed with the selected OSR at
buffer enable time and before each single-shot read.
Supported OSR values: 1, 2, 4, 8, 16, 32.
Introduce AD4691_MANUAL_CHANNEL() for manual mode channels, which do
not expose the oversampling_ratio attribute since OSR is not applicable
in that mode. A separate manual_channels array is added to
struct ad4691_channel_info and selected at probe time.
The OSR is shared across all channels (in_voltage_sampling_frequency
and in_voltage_oversampling_ratio are info_mask_shared_by_all) because
the chip has one internal oscillator and a single accumulator depth
register (ACC_DEPTH_IN(0)) for all channels.
in_voltage_sampling_frequency represents the effective output rate,
defined as osc_freq / osr. Writing it computes needed_osc = freq * osr
and snaps down to the largest oscillator table entry that satisfies both
osc <= needed_osc and osc % osr == 0, guaranteeing an exact integer
read-back. The result is stored in target_osc_freq_Hz and written to
OSC_FREQ_REG at buffer enable and single-shot time, so sampling_frequency
and oversampling_ratio can be set in any order.
in_voltage_sampling_frequency_available is precomputed at probe for
each OSR value, listing only oscillator table entries that divide
evenly by that OSR, expressed as effective rates (osc_freq / osr).
The list becomes sparser as OSR increases, capping at max_rate / osr.
read_avail picks the precomputed list for the current OSR, making the
returned pointer stable and race-free.
Writing oversampling_ratio stores the new shared OSR and snaps
target_osc_freq_Hz to the largest oscillator table entry that is both
<= old_effective_rate * new_osr and evenly divisible by new_osr. This
preserves an integer read-back of in_voltage_sampling_frequency after
the OSR change while keeping the oscillator as close as possible to the
previous effective rate.
OSR defaults to 1 (no accumulation).
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add SPI offload support to enable DMA-based, CPU-independent data
acquisition using the SPI Engine offload framework.
When an SPI offload is available (devm_spi_offload_get() succeeds),
the driver registers a DMA engine IIO buffer and uses dedicated buffer
setup operations. If no offload is available the existing software
triggered buffer path is used unchanged.
Both CNV Burst Mode and Manual Mode support offload, but use different
trigger mechanisms:
CNV Burst Mode: the SPI Engine is triggered by the ADC's DATA_READY
signal on the GP pin specified by the trigger-source consumer reference
in the device tree (one cell = GP pin number 0-3). For this mode the
driver acts as both an SPI offload consumer (DMA RX stream, message
optimization) and a trigger source provider: it registers the
GP/DATA_READY output via devm_spi_offload_trigger_register() so the
offload framework can match the '#trigger-source-cells' phandle and
automatically fire the SPI Engine DMA transfer at end-of-conversion.
Manual Mode: the SPI Engine is triggered by a periodic trigger at
the configured sampling frequency. The pre-built SPI message uses
the pipelined CNV-on-CS protocol: N+1 16-bit transfers are issued
for N active channels (the first result is discarded as garbage from
the pipeline flush) and the remaining N results are captured by DMA.
All offload transfers use 16-bit frames (bits_per_word=16, len=2).
The SPI Engine assembles received bits into native 16-bit words before
DMA, so offload samples land in CPU-native byte order (IIO_CPU).
Dedicated channel arrays (AD4691_OFFLOAD_CHANNEL) reflect this: they
omit IIO_BE and carry no soft timestamp (DMA delivers data directly to
userspace). The software triggered-buffer path retains its IIO_BE
channels because bits_per_word=8 causes SPI to deliver bytes MSB-first
into memory, making the on-disk layout big-endian. Both paths use
storagebits=16 as transfers are 16 bits wide in both cases.
IIO_BUFFER_DMAENGINE is selected because the offload path uses
devm_iio_dmaengine_buffer_setup_with_handle() to allocate and
attach the DMA RX buffer to the IIO device.
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add buffered capture support using the IIO triggered buffer framework.
CNV Burst Mode: the GP pin identified by interrupt-names in the device
tree is configured as DATA_READY output. The IRQ handler stops
conversions and fires the IIO trigger; the trigger handler executes a
pre-built SPI message that reads all active channels from the AVG_IN
accumulator registers and then resets accumulator state and restarts
conversions for the next cycle.
Manual Mode: CNV is tied to SPI CS so each transfer simultaneously
reads the previous result and starts the next conversion (pipelined
N+1 scheme). At preenable time a pre-built, optimised SPI message of
N+1 transfers is constructed (N channel reads plus one NOOP to drain
the pipeline). The trigger handler executes the message in a single
spi_sync() call and collects the results. An external trigger (e.g.
iio-trig-hrtimer) is required to drive the trigger at the desired
sample rate.
Both modes share the same trigger handler and push a complete scan —
one big-endian 16-bit (__be16) slot per active channel, densely packed
in scan_index order, followed by a timestamp.
The CNV Burst Mode sampling frequency (PWM period) is exposed as a
buffer-level attribute via IIO_DEVICE_ATTR.
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the Analog Devices AD4691 family of high-speed,
low-power multichannel SAR ADCs: AD4691 (16-ch, 500 kSPS),
AD4692 (16-ch, 1 MSPS), AD4693 (8-ch, 500 kSPS) and
AD4694 (8-ch, 1 MSPS).
The driver implements a custom regmap layer over raw SPI to handle the
device's mixed 1/2/3/4-byte register widths and uses the standard IIO
read_raw/write_raw interface for single-channel reads.
The chip idles in Autonomous Mode so that single-shot read_raw can use
the internal oscillator without disturbing the hardware configuration.
Three voltage supply domains are managed: avdd (required), vio, and a
reference supply on either the REF pin (ref-supply, external buffer)
or the REFIN pin (refin-supply, uses the on-chip reference buffer;
REFBUF_EN is set accordingly). Hardware reset is performed by asserting
then deasserting the reset-gpios GPIO line (tRESETL minimum pulse width
is 10 ns, satisfied by function-call overhead); the driver then waits
300 µs for the chip to complete its internal reset sequence. A software
reset via SPI_CONFIG_A is used as fallback when no reset GPIO is
provided.
Accumulator channel masking for single-shot reads uses ACC_MASK_REG via
an ADDR_DESCENDING SPI write, which covers both mask bytes in a single
16-bit transfer.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add DT bindings for the Analog Devices AD4691 family of multichannel
SAR ADCs (AD4691, AD4692, AD4693, AD4694).
The four variants are not compatible with each other: AD4691/AD4692 have
16 analog input channels while AD4693/AD4694 have 8, and AD4691/AD4693
top out at 500 kSPS while AD4692/AD4694 reach 1 MSPS. These differences
in channel count and maximum sample rate require distinct compatible
strings so the driver can select the correct channel configuration and
rate limits.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the AD4884, a dual-channel, 16-bit, 40 MSPS SAR ADC.
The AD4884 is the dual-channel variant of the AD4084, sharing the same
register map and SPI interface as the rest of the AD4080 family. Like
the AD4880, it uses two independent ADC channels, each with its own SPI
configuration interface.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add AD4884 compatible string to the AD4080 devicetree binding.
The AD4884 is a dual-channel, 16-bit, 40 MSPS SAR ADC, sharing the same
register map and interface as the AD4080 family. Like the AD4880, it
requires two SPI chip selects and two io-backends for its independent
ADC channels. The AD4884 differs from the AD4880 in resolution (16-bit
vs 20-bit), which requires distinct channel configuration in the driver,
precluding a fallback compatible.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace switch statements with an indexed lookup table for
persist cycle conversions.
Both functions contain redundant switch statements. This
reduces code duplication and makes future updates to
TSL2591_PRST_ALS_INT_CYCLE_* definitions easier to maintain
by keeping the mapping in a single place.
Signed-off-by: Matheus Silveira <matheus.feitosa@usp.br>
Co-developed-by: Lucas Rabaquim <lucas.rabaquim@usp.br>
Signed-off-by: Lucas Rabaquim <lucas.rabaquim@usp.br>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Named initializers are better readable and more robust to changes of the
struct definition. This robustness is relevant for a planned change to
struct platform_device_id replacing .driver_data by an anonymous union.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADT7604 shares the same die as the LTC2984. It repurposes the
custom RTD sensor type (18) as a copper trace resistance sensor
and the custom thermistor type (27) as a leak detector, and
removes thermocouple, diode and direct ADC sensor types.
Two new software sensor type values are introduced
(LTC2983_SENSOR_COPPER_TRACE = 32, LTC2983_SENSOR_LEAK_DETECTOR = 33)
that map to the hardware register values 18 and 27 respectively.
Dedicated structs (ltc2983_copper_trace, ltc2983_leak_detector) and
parser functions are added rather than extending the existing RTD and
thermistor paths, as the hardware configuration bits are fully
hardcoded and several RTD/thermistor properties would need to be
explicitly forbidden or ignored.
Custom RTD (type 18) becomes the copper trace sensor. Sensor
configuration bits are hardcoded to 0b1001 per the datasheet.
Two variants are supported via the adi,copper-trace-sub-ohm DT
property: sub-ohm traces (< 1 ohm) have bits 17:0 cleared with no
excitation current or custom table; standard traces (> 1 ohm) have
a required resistance-to-temperature table.
Custom thermistor (type 27) becomes the leak detector. Sensor
configuration bits are hardcoded to 0b001. The custom table uses
a resolution of 16 instead of 64, and is specified via the
required adi,custom-leak-detector DT property.
Both sensor types expose an IIO_RESISTANCE channel reading from
the resistance result register bank (0x0060-0x00AF). Added a
"base" parameter to the LTC2983_RESULT_ADDR macro and a "base_reg"
parameter to the ltc2983_chan_read function so we can read from
both result register banks. The resistance register encodes the
measured resistance with 10 fractional bits, so dividing by 1024
gives ohms. Since the sense resistor is specified in ohms, the
output is in ohms for both sensor types and a single 1/1024
scale applies to both. For > 1 ohm copper traces and for leak
detectors, a secondary channel also appears: IIO_TEMP
(millidegrees Celsius) for copper trace and IIO_COVERAGE (percent)
for leak detector.
The ltc2983_chip_info struct is extended with a u64 supported_sensors
bitmask using BIT_ULL() to safely represent the new sensor type bits
32 and 33 on 32-bit builds. A LTC2983_SENSOR_NUM sentinel is added
to the enum so that the bounds check uses >= LTC2983_SENSOR_NUM
rather than hardcoding the last sensor type.
Tested on EVAL-ADT7604-AZ connected to Raspberry Pi 5 via SPI.
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADT7604 shares the same die as the LTC2984. It repurposes the
custom RTD sensor type (18) as a copper trace resistance sensor
and the custom thermistor type (27) as a leak detector, and
removes thermocouple, diode and direct ADC sensor types.
Add adi,adt7604 to the compatible list and introduce two new
sensor node types specific to this device:
- copper-trace@: maps to the custom RTD sensor type (18). Two
variants: sub-ohm (< 1 ohm, adi,copper-trace-sub-ohm boolean,
no custom table and excitation current) and standard (> 1 ohm,
required adi,custom-copper-trace table, optional excitation current
defaulting to the datasheet recommended value). Primary output
is resistance in ohms. For > 1 ohm copper traces with a custom table,
the chip also outputs temperature in millidegrees Celsius.
- leak-detector@: maps to the custom thermistor sensor type (27).
Takes a required adi,custom-leak-detector lookup table encoding
resistance (uOhm) against coverage data (%). Two outputs:
resistance in ohms and coverage in percent.
Separate node types are used rather than extending the existing
rtd@ and thermistor@ nodes because adi,custom-rtd is required
for sensor type 18, and several properties (adi,number-of-wires,
adi,rtd-curve, adi,rsense-share, adi,single-ended,
adi,current-rotate) have no meaning for the new sensor types, since
the configuration is hardcoded, and would need to be explicitly
forbidden or ignored in the driver.
allOf conditions are added to restrict thermocouple, diode, direct
ADC and active temperature nodes to non-ADT7604 devices, and to
restrict copper-trace and leak-detector nodes to the ADT7604
(some parts only).
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a new channel type for sensors that report fractional coverage as
a percentage. The sysfs attribute is in_coverageY_raw; after applying
in_coverageY_scale the value is in percent. The first user is the
ADT7604 leak detector, where the value represents the portion of the
sensing element that is wetted.
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Checking fwnode_property_read_u32() return value with if (!ret)
silently swallows meaningful error codes when a property is present
but malformed. Use fwnode_property_present() first so that absence
uses the default while a present but unreadable property returns
a proper error.
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace occurrences of the abbreviated 'chann' and 'chan' with
'channel' in error and debug messages throughout the driver.
Also changed the diode invalid channel error message from
"thermistor" to "diode".
Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some functions define a local 'dev' pointer but still use bare
'&st->spi->dev' in some code paths, and some don't have it at all.
Replace bare references with the local pointer for consistency and
collapse some wrapped lines that now fit within 80 characters.
Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Wrap the 'chan' parameter in LTC2983_CHAN_START_ADDR() and
LTC2983_CHAN_RES_ADDR() with parentheses to prevent potential
macro argument expansion issues. Also rename LTC2983_CHAN_START_ADDR
to LTC2983_CHAN_ASSIGN_ADDR and LTC2983_CHAN_RES_ADDR to
LTC2983_RESULT_ADDR, to better reflect the datasheet names and avoid
them being confused as related.
Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
reinit_completion() was called after regmap_write() initiated the hardware
conversion, creating a race window where the interrupt could fire and call
complete() before reinit_completion() reset the completion.
Move reinit_completion() before the regmap_write() to close the race.
ltc2983_eeprom_cmd() already does it in the correct order.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When adi,number-of-wires is absent, n_wires is left at 0. The binding
documents a default of 2 wires, matching the hardware default. However
the current-rotate validation checks n_wires == 2 || n_wires == 3, so
with n_wires = 0 the guard is bypassed and adi,current-rotate is accepted
for a 2-wire RTD.
Initialize n_wires = 2 to match the binding default and ensure the
rotation check fires correctly when the property is absent.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add IIO driver for Broadcom APDS9999 ambient light sensor.
The APDS9999 is a digital proximity and RGB sensor with ALS
capability. The driver implements the ALS/Lux functionality
using the green channel, which uses optical coating technology
to approximate the human eye spectral response.
Raw IIO_INTENSITY channels are exposed for red, green, blue,
and IR so userspace can compute its own weighted lux.
Proximity (PS) support is not yet implemented.
Signed-off-by: Jose A. Perez de Azpillaga <azpijr@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add Device Tree binding for the Broadcom APDS9999 ambient light
and proximity sensor. A separate binding file is used rather
than merging with avago,apds9300.yaml because the APDS9999
has an additional vcsel-supply for the VCSEL.
The APDS9999 features individual R, G, B, and IR channels with
a green channel that uses optical coating to approximate the
human eye spectral response for ALS/lux measurements. Calibrated
RGB color sensing is not yet implemented in the driver.
Signed-off-by: Jose A. Perez de Azpillaga <azpijr@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove unused includes and add what is being used:
#include <linux/array_size.h> // for ARRAY_SIZE
#include <linux/bits.h> // for GENMASKxx
#include <linux/dev_printk.h> // for dev_err_probe, dev_info
#include <linux/math.h> // for DIV_ROUND_UP
#include <linux/mutex.h> // for struct mutex
#include <linux/types.h> // for uXX definitions
#include <linux/iio/types.h> // for IIO_CHAN_INFO_*
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sort includes alphabetically, no functional change
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use IIO_CHAN_SOFT_TIMESTAMP() to define the timestamp channel instead of
manually filling in the struct iio_chan_spec fields. This makes the code
less verbose and mistake-prone.
Also drop obvious comment while we're at it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use IIO_CHAN_SOFT_TIMESTAMP() to define the timestamp channel instead of
manually filling in the struct iio_chan_spec fields. This makes the code
less verbose and mistake-prone.
Also drop obvious comment while we're at it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use IIO_CHAN_SOFT_TIMESTAMP() to define the timestamp channel instead of
manually filling in the struct iio_chan_spec fields. This makes the code
less verbose and mistake-prone.
Also drop obvious comment while we're at it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use IIO_CHAN_SOFT_TIMESTAMP() to define the timestamp channel instead of
manually filling in the struct iio_chan_spec fields. This makes the code
less verbose and mistake-prone.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use IIO_CHAN_SOFT_TIMESTAMP() to define the timestamp channel instead of
manually filling in the struct iio_chan_spec fields. This makes the code
less verbose and mistake-prone.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use IIO_CHAN_SOFT_TIMESTAMP() to define the timestamp channel instead of
manually filling in the struct iio_chan_spec fields. This makes the code
less verbose and mistake-prone.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use IIO_CHAN_SOFT_TIMESTAMP() to define the timestamp channel instead of
manually filling in the struct iio_chan_spec fields. This makes the code
less verbose and mistake-prone.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use IIO_CHAN_SOFT_TIMESTAMP() to define the timestamp channel instead of
manually filling in the struct iio_chan_spec fields. This makes the code
less verbose and mistake-prone.
In fact, there was an error here as the sign should be 's' instead of
'u' which is now changed to 's' by using IIO_CHAN_SOFT_TIMESTAMP().
If we find that this breaks userspace, we will have to revert this
change, but seems unlikely since the timestamp channel is well-known to
be a signed 64-bit integer globally.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently IIO_CHAN_SOFT_TIMESTAMP() can only be used to fill the static
data. In some cases it would be convenient to use it as right value in
the assignment operation. But it can't be done as is, because compiler
has no clue about the data layout. Converting it to be a compound literal
allows the above mentioned usage.
While at it, tidy up the indentation.
We also have to change existing uses of compound literal at the same
time to avoid compiler errors.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
