There is no need to populate the ckdv[] with invalid dividers as that
part will not be indexed anyway. The ssi->audio_mck/bclk_rate should
always be >= 0. While at it, change the ckdv type as u8, as the divider
128 was previously using the s8 sign bit.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Fixes: 03e786bd43 ("ASoC: sh: Add RZ/G2L SSIF-2 driver")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20241210170953.2936724-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The stop trigger invokes rz_ssi_stop() and rz_ssi_stream_quit().
- The purpose of rz_ssi_stop() is to disable TX/RX, terminate DMA
transactions, and set the controller to idle.
- The purpose of rz_ssi_stream_quit() is to reset the substream-specific
software data by setting strm->running and strm->substream appropriately.
The function rz_ssi_is_stream_running() checks if both strm->substream and
strm->running are valid and returns true if so. Its implementation is as
follows:
static inline bool rz_ssi_is_stream_running(struct rz_ssi_stream *strm)
{
return strm->substream && strm->running;
}
When the controller is configured in full-duplex mode (with both playback
and capture active), the rz_ssi_stop() function does not modify the
controller settings when called for the first substream in the full-duplex
setup. Instead, it simply sets strm->running = 0 and returns if the
companion substream is still running. The following code illustrates this:
static int rz_ssi_stop(struct rz_ssi_priv *ssi, struct rz_ssi_stream *strm)
{
strm->running = 0;
if (rz_ssi_is_stream_running(&ssi->playback) ||
rz_ssi_is_stream_running(&ssi->capture))
return 0;
// ...
}
The controller settings, along with the DMA termination (for the last
stopped substream), are only applied when the last substream in the
full-duplex setup is stopped.
While applying the controller settings only when the last substream stops
is not problematic, terminating the DMA operations for only one substream
causes failures when starting and stopping full-duplex operations multiple
times in a loop.
To address this issue, call dmaengine_terminate_async() for both substreams
involved in the full-duplex setup when the last substream in the setup is
stopped.
Fixes: 4f8cd05a43 ("ASoC: sh: rz-ssi: Add full duplex support")
Cc: stable@vger.kernel.org
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20241210170953.2936724-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
These patches tidyup simple-card-utils for Multi connection of
Audio Graph Card, Because of DT node parsing, it should check port
1st instead of endpoint. Otherwise, it can't handle DAI correctly.
Merge series from Chancel Liu <chancel.liu@nxp.com>:
Platforms like i.MX93/91 only have one audio PLL. Some sample rates are
not supported. If the PLL source is used for 8kHz series rates, then
11kHz series rates can't be supported. Add common function to constrain
rates according to different clock sources.
In ASoC drivers switch to this new function.
Merge series from codekipper@gmail.com:
I've tested this patch series on the Allwinner H3, A64, H6 and H313 SoCs
up to 192KHz.
24bit support is working on my H313 board but 16bit plays a bit slow and
I suspect that there is an issue with the clock setups. This is even
present without this patch stack. I would look to address this asap,
but for now can you please review what's here.
24 bit audio file can be detected by the alsa driver as S32_LE.
Add this format to what is supported and change the DMA address
width.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Link: https://patch.msgid.link/20241111165600.57219-4-codekipper@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There have been intermittent issues with the SPDIF output on H3
and H2+ devices which has been fixed by setting the s_clk to 4
times the audio pll.
Add a quirk for the clock multiplier as not every supported SoC
requires it. Without the multiplier, the audio at normal sampling
rates was distorted and did not play at higher sampling rates.
Fixes: 1bd92af877 ("ASoC: sun4i-spdif: Add support for the H3 SoC")
Signed-off-by: George Lander <lander@jagmn.com>
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Link: https://patch.msgid.link/20241111165600.57219-2-codekipper@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-21-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-20-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-19-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-18-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-17-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-16-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-15-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-14-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-13-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-12-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-11-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-10-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-9-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-8-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-7-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-6-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-5-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-4-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-3-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-2-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-1-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Number of DAIs in the codec is not really a binding constant, because it
could grow, e.g. when we implement missing features.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241209094442.38900-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Number of DAIs in the codec is not really a binding, because it could
grow, e.g. when we implement missing features. Add the define to the
driver, which will replace the one in the binding header.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241209094442.38900-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add some new match table entries on Arrowlake for some coming cs42l43
laptops.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As there are many combinations these follow a naming scheme to make
the content of link structures clearer:
cs35l56_<controller link>_<l or r><unique instance id>_adr
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt713_vb on SoundWire link 2 and rt1320 on SoundWire link 1 and 3
configuration support.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt713_vb on SoundWire link 2 and rt1320 on SoundWire link 1 and 3
configuration support.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt712_vb on SDW link 2 and 1 rt1320 on SDW link 1 configuration
support.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add debug message when SOC_SDW_CODEC_MIC is enabled (which informs the
machine driver to not bind in the cs42l43 microphone DAI link).
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In addition to changing the DMI match to examine the product name rather
than the SKU, this adds the quirk to inform the machine driver to not
bind in the cs42l43 microphone DAI link.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The log shows the number for different type of DAIs. Add "DAI link
numbers:" to make the log be more explicit.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ctx->ignore_internal_dmic is set when there is a dedicated SoundWire
DMIC is in the system. In other words, ignoring internal DMIC is
expected, not an error.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
mach_params->dmic_num will be used to set the cfg-mics value of
card->components string which should be the dmic channels. However
dmic_num is dmic link number and could be set due to the SOC_SDW_PCH_DMIC
quirk. Set mach_params->dmic_num to the default value if the dmic link
is created due to the SOC_SDW_PCH_DMIC quirk.
Fixes: 7db9f63611 ("ASoC: Intel: sof_sdw: overwrite mach_params->dmic_num")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20241206075903.195730-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because DT check when compiling become very strict in these days,
we need to add reg = <x> if it has multi port/endpoint, otherwise
it will get error or warning. But it was not so strict and/or
mandatry before.
Current code is counting "endpoint" to get DAI ID, but it should count
"port" instead, otherwise strange ID will be used for DAI if it was multi
connected case (A). There is no issue if it was not multi connected (B).
One note is that this code will be used if neither port/endpoint doesn't
have reg = <x> property on DT.
case (A)
/* This should be handled as DAI-0 */
port@0 {
endpoint@0 { } /* It will be DAI-0 by endpoint count */
endpoint@1 { } /* It will be DAI-1 by endpoint count */
};
/* This should be handled as DAI-1 */
port@1 {
endpoint { } /* It will be DAI-2 by endpoint count */
};
case (B)
/* both endpoint cound and port count are same */
port@0 {
endpoint { ... }
};
port@1 {
endpoint { ... }
};
It will be issue if Audio-Graph-Card is used with Multi Connection.
No issue will be happen with Audio-Graph-Card2 / Simple-Card.
This patch uses for_each_of_graph_port() instead of
for_each_endpoint_of_node(), and thus, we can use "break" to quit
from loop. Because for_each_of_graph_port() uses __free(device_node)
inside.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87o71tfrdz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because DT check when compiling become very strict in these days,
we need to add reg = <x> if it has multi port/endpoint, otherwise
it will get error or warning. But it was not so strict and/or
mandatry before.
Current code uses reg number as DAI ID, but it will use "endpoint"
reg first and use "port" reg 2nd. But it should use port number as 1st (A)
if it was used for multi connected case. There is no priority for
port/endpoint if it was not multi connected (B).
case (A)
port {
/*
* "port" and "endpoint" are using different reg number.
* It should use <x> as DAI ID, not <y> not <z>
*/
reg = <x>;
endpoint@y { reg = <y>; ... };
endpoint@z { reg = <z>; ... };
};
case (B)
port {
/*
* Both port/endpoint are using same reg numer <x>.
*/
reg = <x>;
endpoint { reg = <x>; ... };
};
It will be issue if Audio-Graph-Card is used with Multi Connection.
No issue will be happen with Audio-Graph-Card2 / Simple-Card.
This patch swtich port/endpoint priority.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87plm9fre3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-card-utils handles many type of device_node, thus need to
use of_node_put() in many place. Let's use __free(device_node)
and avoid it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87r06pfre8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Platforms like i.MX93/91 only have one audio PLL. Some sample rates are
not supported. If the PLL source is used for 8kHz series rates, then
11kHz series rates can't be supported. Use fsl_asoc_constrain_rates()
to constrain rates according to PLL sources.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://patch.msgid.link/20241126115440.3929061-5-chancel.liu@nxp.com
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Platforms like i.MX93/91 only have one audio PLL. Some sample rates are
not supported. If the PLL source is used for 8kHz series rates, then
11kHz series rates can't be supported. Use fsl_asoc_constrain_rates()
to constrain rates according to PLL sources. This constraint is merely
applicable to playback cases on SPDIF only platforms.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://patch.msgid.link/20241126115440.3929061-4-chancel.liu@nxp.com
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_asoc_constrain_rates() is a common function to constrain rates.
Let's switch to this function.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://patch.msgid.link/20241126115440.3929061-3-chancel.liu@nxp.com
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
