A minor refactor to combine the subroutines for legacy a6xx GMUs under
a single check. This helps to avoid an unnecessary check and return
early from the subroutine for majority of a6xx gpus.
Also, document an intermediate unknown low power state which is not
exposed by the GMU firmware.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673364/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Since the PDC resides out of the GPU subsystem and cannot be reset in
case it enters bad state, utmost care must be taken to trigger the PDC
wake/sleep routines in the correct order.
The PDC wake sequence can be exercised only after a PDC sleep sequence.
Additionally, GMU firmware should initialize a few registers before the
KMD can trigger a PDC sleep sequence. So PDC sleep can't be done if the
GMU firmware has not initialized. Track these dependencies using a new
status variable and trigger PDC sleep/wake sequences appropriately.
Cc: stable@vger.kernel.org
Fixes: 4b565ca5a2 ("drm/msm: Add A6XX device support")
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673362/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
A7XX_GEN2 generation has additional TCS slots. Poll the respective
DRV status registers before pm suspend.
Fixes: 1f8c29e800 ("drm/msm/a6xx: Add A740 support")
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673361/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Bitfield definition for REG_A6XX_GMU_SPTPRAC_PWR_CLK_STATUS register is
different in A7XX family. Check the correct bits to see if GX is
collapsed on A7XX series.
Fixes: af66706acc ("drm/msm/a6xx: Add skeleton A7xx support")
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673358/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Update GMU register xml with additional definitions for a7x family.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673356/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Descirbe A505 clocks it is using same clocks like A506.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Patchwork: https://patchwork.freedesktop.org/patch/672751/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Use the msm_kms_init_vm() function to allocate memory manager instead of
hand-coding a copy of it. Although MDP4 platforms don't have MDSS
device, it's still safe to use the function as all MDP4 devices have
IOMMU and the parent of the MDP4 is the root SoC device.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/672563/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
As we've dropped no-IOMMU support, there is no reason to specially
handle the no-IOMMU case inside msm_iommu_new(). Make it return -ENODEV
if there is no IOMMU (instead of returning NULL) and simplify all
calling sites accordingly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/672561/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
With the switch to GPUVM the msm driver no longer supports the no-IOMMU
configurations (even without the actual GPU). Return an error in case we
face the lack of the IOMMU.
Fixes: 111fdd2198 ("drm/msm: drm_gpuvm conversion")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/672559/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
With the switch to GPUVM the msm driver no longer supports the no-IOMMU
configurations (even without the actual GPU). Return an error in case we
face the lack of the IOMMU for an MDP4 device.
Fixes: 111fdd2198 ("drm/msm: drm_gpuvm conversion")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/672557/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Add the speedbin mappings for Adreno 623 GPU.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/672462/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Update Adreno 623's dt-binding to remove smmu_clk which is not required
for this GMU.
Signed-off-by: Jie Zhang <quic_jiezh@quicinc.com>
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/672455/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
If two fault IRQs arrive in short succession recovery work will be
queued up twice.
When recovery runs a second time it may end up killing an unrelated
context.
Prevent this by masking off interrupts when triggering recovery.
Signed-off-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/670023/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
The Adreno GPU Management Unit (GMU) can also scale DDR Bandwidth along
the Frequency and Power Domain level, but by default we leave the
OPP core scale the interconnect ddr path.
Declare the Bus Control Modules (BCMs) and the corresponding parameters
in the GPU info struct to allow the GMU to vote for the bandwidth.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/665778/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
This is always set in msm_gpu_init(), and can never be NULL.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/664431/
Somehow we never noticed this when arm64 became a thing, many years ago.
v2: also fix npages
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/669785/
We need to reject the MAP op if offset+range is larger than the BO size.
Reported-by: Connor Abbott <cwabbott0@gmail.com>
Fixes: 2e6a8a1fe2 ("drm/msm: Add VM_BIND ioctl")
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/669781/
If we fail a handle-lookup part way thru, we need to drop the already
obtained obj references.
Fixes: 2e6a8a1fe2 ("drm/msm: Add VM_BIND ioctl")
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/669784/
On a vast majority of Qualcomm chipsets DisplayPort controller can
support several MST streams (up to 4x). To support MST these chipsets
use up to 4 stream pixel clocks for the DisplayPort controller and
several extra register regions. Expand corresponding region and clock
bindings for these platforms and fix example schema files to follow
updated bindings.
Note: On chipsets that support MST, the number of streams supported
can vary between controllers. For example, SA8775P supports 4 MST
streams on mdss_dp0 but only 2 streams on mdss_dp1.
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/672585/
Link: https://lore.kernel.org/r/20250903-dp_mst_bindings-v8-7-7526f0311eaa@oss.qualcomm.com
DP controller schema documents assigned-clocks and
assigned-clock-parents. However these assignments should not be a part
of the ABI: there are no actual requirements on the order of the
assignments, MST cases require different number of clocks to be
assigned, etc.
Instead of fixing up the documentation, drop the assigned-clock-parents
and assigned-clocks from the bindings. The generic clock/clock.yaml
already covers these properties.
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/672586/
Link: https://lore.kernel.org/r/20250903-dp_mst_bindings-v8-6-7526f0311eaa@oss.qualcomm.com
Fix c&p error and correct example to use 32-bit addressing (as the rest
of the example DT does) instead of 64-bit (as the platform does). It
got unnoticed before since DP controller node wasn't validated against
DT schema because of the missing compatible.
Fixes: 81de267367 ("dt-bindings: display/msm: Document MDSS on X1E80100")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/672574/
Link: https://lore.kernel.org/r/20250903-dp_mst_bindings-v8-4-7526f0311eaa@oss.qualcomm.com
Currently SM6350 uses qcom,sm8350-dp as a fallback compatible entry.
This works, but adding DP MST support will reveal that this SoC is
not fully compatible with SM8350 platform: the former one doesn't
provide MST support, while the latter one will get it. DT schema for
SM8350 is going to demand MST-related clocks which SM6350 doesn't
provide.
Add new entry for SM6350 with fallback to SC7180 (which belongs to the
same generation and also doesn't have MST support). SC7180 has been
supported by the Linux kernel long ago (and long before SM8350 support
was added).
Fixes: 3908615159 ("dt-bindings: display: msm: dp-controller: document SM6350 compatible")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/672571/
Link: https://lore.kernel.org/r/20250903-dp_mst_bindings-v8-2-7526f0311eaa@oss.qualcomm.com
Currently, only one pair of mixers is supported, so a non-zero counter
value is sufficient to identify the correct mixer within that pair.
However, future implementations may involve multiple mixer pairs. With
the current implementation, all mixers within the second pair would be
incorrectly selected as right mixer. To correctly select the mixer
within a pair, test the least significant bit of the counter. If the
least significant bit is not set, select the mixer as left one;
otherwise, select the mixer as right one for all pairs.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/669226/
Link: https://lore.kernel.org/r/20250819-v6-16-rc2-quad-pipe-upstream-v15-3-2c7a85089db8@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
It is more likely that resource allocation may fail in complex usage
case, such as quad-pipe case, than existing usage cases.
A resource type ID is printed on failure in the current implementation,
but the raw ID number is not explicit enough to help easily understand
which resource caused the failure, so add a table to match the type ID
to an human readable resource name and use it in the error print.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/669225/
Link: https://lore.kernel.org/r/20250819-v6-16-rc2-quad-pipe-upstream-v15-2-2c7a85089db8@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Driver unconditionally saves current state on first init in
dsi_pll_7nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_7nm_pll_restore_state().
Restoring calls dsi_pll_7nm_vco_set_rate() with
pll_7nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/657827/
Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-9-ee633e3ddbff@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
According to Hardware Programming Guide for DSI PHY, the retime buffer
resync should be done after PLL clock users (byte_clk and intf_byte_clk)
are enabled. Downstream also does it as part of configuring the PLL.
Driver was only turning off the resync FIFO buffer, but never bringing it
on again.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/657823/
Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-6-ee633e3ddbff@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series.
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
Patchwork: https://patchwork.freedesktop.org/patch/667982/
Link: https://lore.kernel.org/r/20250811-drm-clk-round-rate-v2-4-4a91ccf239cf@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series.
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
Patchwork: https://patchwork.freedesktop.org/patch/667980/
Link: https://lore.kernel.org/r/20250811-drm-clk-round-rate-v2-3-4a91ccf239cf@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667878/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-7-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667876/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-6-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667874/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-5-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667872/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-4-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667870/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-3-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667869/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-2-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667866/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-1-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
irq_domain_create_simple() takes fwnode as the first argument. It can be
extracted from the struct device using dev_fwnode() helper instead of
using of_node with of_fwnode_handle().
So use the dev_fwnode() helper.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <lumag@kernel.org>
Cc: Sean Paul <sean@poorly.run>
Cc: Marijn Suijten <marijn.suijten@somainline.org>
Cc: David Airlie <airlied@gmail.com>
Cc: Simona Vetter <simona@ffwll.ch>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/665227/
Link: https://lore.kernel.org/r/20250723055512.1800438-1-jirislaby@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Use the newly added of_reserved_mem_region_to_resource() function to
handle "memory-region" properties.
The original code did not set 'zap_available' to false if
of_address_to_resource() failed which seems like an oversight.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662275/
Link: https://lore.kernel.org/r/20250703183442.2073717-1-robh@kernel.org
[DB: dropped part related to VRAM, no longer applicable]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
