Shenghao Yang says:
====================
net: dsa: mv88e6xxx: fix MV88E6393X PHC frequency on internal clock
The MV88E6393X family of switches can additionally run their cycle
counters using a 250MHz internal clock instead of the usual 125MHz
external clock [1].
The driver currently assumes all designs utilize that external clock,
but MikroTik's RB5009 uses the internal source - causing the PHC to be
seen running at 2x real time in userspace, making synchronization
with ptp4l impossible.
This series adds support for reading off the cycle counter frequency
known to the hardware in the TAI_CLOCK_PERIOD register and picking an
appropriate set of scaling coefficients instead of using a fixed set
for each switch family.
Patch 1 groups those cycle counter coefficients into a new structure to
make it easier to pass them around.
Patch 2 modifies PTP initialization to probe TAI_CLOCK_PERIOD and
use an appropriate set of coefficients.
Patch 3 adds support for 4000ps cycle counter periods.
Changes since v2 [2]:
- Patch 1: "net: dsa: mv88e6xxx: group cycle counter coefficients"
- Moved declaration of mv88e6xxx_cc_coeffs to avoid moving that in
Patch 2.
- Patch 2: "net: dsa: mv88e6xxx: read cycle counter period from hardware"
- Removed move of mv88e6xxx_cc_coeffs declaration.
- Patch 3: "net: dsa: mv88e6xxx: support 4000ps cycle counter periods"
- No change.
[1] https://lore.kernel.org/netdev/d6622575-bf1b-445a-b08f-2739e3642aae@lunn.ch/
[2] https://lore.kernel.org/netdev/20241006145951.719162-1-me@shenghaoyang.info/
====================
Link: https://patch.msgid.link/20241020063833.5425-1-me@shenghaoyang.info
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The MV88E6393X family of devices can run its cycle counter off
an internal 250MHz clock instead of an external 125MHz one.
Add support for this cycle counter period by adding another set
of coefficients and lowering the periodic cycle counter read interval
to compensate for faster overflows at the increased frequency.
Otherwise, the PHC runs at 2x real time in userspace and cannot be
synchronized.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of relying on a fixed mapping of hardware family to cycle
counter frequency, pull this information from the
MV88E6XXX_TAI_CLOCK_PERIOD register.
This lets us support switches whose cycle counter frequencies depend on
board design.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of having them as individual fields in ptp_ops, wrap the
coefficients in a separate struct so they can be referenced together.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The existing code moves VF to the same namespace as the synthetic NIC
during netvsc_register_vf(). But, if the synthetic device is moved to a
new namespace after the VF registration, the VF won't be moved together.
To make the behavior more consistent, add a namespace check for synthetic
NIC's NETDEV_REGISTER event (generated during its move), and move the VF
if it is not in the same namespace.
Cc: stable@vger.kernel.org
Fixes: c0a41b887c ("hv_netvsc: move VF to same namespace as netvsc device")
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1729275922-17595-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The well-known errata regarding EEE not being functional on various KSZ
switches has been refactored a few times. Recently the refactoring has
excluded several switches that the errata should also apply to.
Disable EEE for additional switches with this errata and provide
additional comments referring to the public errata document.
The original workaround for the errata was applied with a register
write to manually disable the EEE feature in MMD 7:60 which was being
applied for KSZ9477/KSZ9897/KSZ9567 switch ID's.
Then came commit 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata
fixes to PHY driver") and commit 6068e6d7ba ("net: dsa: microchip:
remove KSZ9477 PHY errata handling") which moved the errata from the
switch driver to the PHY driver but only for PHY_ID_KSZ9477 (PHY ID)
however that PHY code was dead code because an entry was never added
for PHY_ID_KSZ9477 via MODULE_DEVICE_TABLE.
This was apparently realized much later and commit 54a4e5c163 ("net:
phy: micrel: add Microchip KSZ 9477 to the device table") added the
PHY_ID_KSZ9477 to the PHY driver but as the errata was only being
applied to PHY_ID_KSZ9477 it's not completely clear what switches
that relates to.
Later commit 6149db4997 ("net: phy: micrel: fix KSZ9477 PHY issues
after suspend/resume") breaks this again for all but KSZ9897 by only
applying the errata for that PHY ID.
Following that this was affected with commit 08c6d8bae48c("net: phy:
Provide Module 4 KSZ9477 errata (DS80000754C)") which removes
the blatant register write to MMD 7:60 and replaces it by
setting phydev->eee_broken_modes = -1 so that the generic phy-c45 code
disables EEE but this is only done for the KSZ9477_CHIP_ID (Switch ID).
Lastly commit 0411f73c13 ("net: dsa: microchip: disable EEE for
KSZ8567/KSZ9567/KSZ9896/KSZ9897.") adds some additional switches
that were missing to the errata due to the previous changes.
This commit adds an additional set of switches.
Fixes: 0411f73c13 ("net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241018160658.781564-1-tharvey@gateworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- hci_core: Disable works on hci_unregister_dev
- SCO: Fix UAF on sco_sock_timeout
- ISO: Fix UAF on iso_sock_timeout
-----BEGIN PGP SIGNATURE-----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=gOTr
-----END PGP SIGNATURE-----
Merge tag 'for-net-2024-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_core: Disable works on hci_unregister_dev
- SCO: Fix UAF on sco_sock_timeout
- ISO: Fix UAF on iso_sock_timeout
* tag 'for-net-2024-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: ISO: Fix UAF on iso_sock_timeout
Bluetooth: SCO: Fix UAF on sco_sock_timeout
Bluetooth: hci_core: Disable works on hci_unregister_dev
====================
Link: https://patch.msgid.link/20241023143005.2297694-1-luiz.dentz@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=Ai21
-----END PGP SIGNATURE-----
Merge tag 'ipsec-2024-10-22' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2024-10-22
1) Fix routing behavior that relies on L4 information
for xfrm encapsulated packets.
From Eyal Birger.
2) Remove leftovers of pernet policy_inexact lists.
From Florian Westphal.
3) Validate new SA's prefixlen when the selector family is
not set from userspace.
From Sabrina Dubroca.
4) Fix a kernel-infoleak when dumping an auth algorithm.
From Petr Vaganov.
Please pull or let me know if there are problems.
ipsec-2024-10-22
* tag 'ipsec-2024-10-22' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: fix one more kernel-infoleak in algo dumping
xfrm: validate new SA's prefixlen using SA family when sel.family is unset
xfrm: policy: remove last remnants of pernet inexact list
xfrm: respect ip protocols rules criteria when performing dst lookups
xfrm: extract dst lookup parameters into a struct
====================
Link: https://patch.msgid.link/20241022092226.654370-1-steffen.klassert@secunet.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
conn->sk maybe have been unlinked/freed while waiting for iso_conn_lock
so this checks if the conn->sk is still valid by checking if it part of
iso_sk_list.
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This make use of disable_work_* on hci_unregister_dev since the hci_dev is
about to be freed new submissions are not disarable.
Fixes: 0d151a1037 ("Bluetooth: hci_core: cancel all works upon hci_unregister_dev()")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If get_clock_desc() succeeds, it calls fget() for the clockid's fd,
and get the clk->rwsem read lock, so the error path should release
the lock to make the lock balance and fput the clockid's fd to make
the refcount balance and release the fd related resource.
However the below commit left the error path locked behind resulting in
unbalanced locking. Check timespec64_valid_strict() before
get_clock_desc() to fix it, because the "ts" is not changed
after that.
Fixes: d8794ac20a ("posix-clock: Fix missing timespec64 check in pc_clock_settime()")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
[pabeni@redhat.com: fixed commit message typo]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It was reported that after resume from suspend a PCI error is logged
and connectivity is broken. Error message is:
PCI error (cmd = 0x0407, status_errs = 0x0000)
The message seems to be a red herring as none of the error bits is set,
and the PCI command register value also is normal. Exception handling
for a PCI error includes a chip reset what apparently brakes connectivity
here. The interrupt status bit triggering the PCI error handling isn't
actually used on PCIe chip versions, so it's not clear why this bit is
set by the chip. Fix this by ignoring this bit on PCIe chip versions.
Fixes: 0e4851502f ("r8169: merge with version 8.001.00 of Realtek's r8168 driver")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219388
Tested-by: Atlas Yu <atlas.yu@canonical.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/78e2f535-438f-4212-ad94-a77637ac6c9c@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In 'taprio_change()', 'admin' pointer may become dangling due to sched
switch / removal caused by 'advance_sched()', and critical section
protected by 'q->current_entry_lock' is too small to prevent from such
a scenario (which causes use-after-free detected by KASAN). Fix this
by prefer 'rcu_replace_pointer()' over 'rcu_assign_pointer()' to update
'admin' immediately before an attempt to schedule freeing.
Fixes: a3d43c0d56 ("taprio: Add support adding an admin schedule")
Reported-by: syzbot+b65e0af58423fc8a73aa@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=b65e0af58423fc8a73aa
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20241018051339.418890-1-dmantipov@yandex.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
tcf_action_init() has logic for checking mismatches between action and
filter offload flags (skip_sw/skip_hw). AFAIU, this is intended to run
on the transition between the new tc_act_bind(flags) returning true (aka
now gets bound to classifier) and tc_act_bind(act->tcfa_flags) returning
false (aka action was not bound to classifier before). Otherwise, the
check is skipped.
For the case where an action is not standalone, but rather it was
created by a classifier and is bound to it, tcf_action_init() skips the
check entirely, and this means it allows mismatched flags to occur.
Taking the matchall classifier code path as an example (with mirred as
an action), the reason is the following:
1 | mall_change()
2 | -> mall_replace_hw_filter()
3 | -> tcf_exts_validate_ex()
4 | -> flags |= TCA_ACT_FLAGS_BIND;
5 | -> tcf_action_init()
6 | -> tcf_action_init_1()
7 | -> a_o->init()
8 | -> tcf_mirred_init()
9 | -> tcf_idr_create_from_flags()
10 | -> tcf_idr_create()
11 | -> p->tcfa_flags = flags;
12 | -> tc_act_bind(flags))
13 | -> tc_act_bind(act->tcfa_flags)
When invoked from tcf_exts_validate_ex() like matchall does (but other
classifiers validate their extensions as well), tcf_action_init() runs
in a call path where "flags" always contains TCA_ACT_FLAGS_BIND (set by
line 4). So line 12 is always true, and line 13 is always true as well.
No transition ever takes place, and the check is skipped.
The code was added in this form in commit c86e0209dc ("flow_offload:
validate flags of filter and actions"), but I'm attributing the blame
even earlier in that series, to when TCA_ACT_FLAGS_SKIP_HW and
TCA_ACT_FLAGS_SKIP_SW were added to the UAPI.
Following the development process of this change, the check did not
always exist in this form. A change took place between v3 [1] and v4 [2],
AFAIU due to review feedback that it doesn't make sense for action flags
to be different than classifier flags. I think I agree with that
feedback, but it was translated into code that omits enforcing this for
"classic" actions created at the same time with the filters themselves.
There are 3 more important cases to discuss. First there is this command:
$ tc qdisc add dev eth0 clasct
$ tc filter add dev eth0 ingress matchall skip_sw \
action mirred ingress mirror dev eth1
which should be allowed, because prior to the concept of dedicated
action flags, it used to work and it used to mean the action inherited
the skip_sw/skip_hw flags from the classifier. It's not a mismatch.
Then we have this command:
$ tc qdisc add dev eth0 clasct
$ tc filter add dev eth0 ingress matchall skip_sw \
action mirred ingress mirror dev eth1 skip_hw
where there is a mismatch and it should be rejected.
Finally, we have:
$ tc qdisc add dev eth0 clasct
$ tc filter add dev eth0 ingress matchall skip_sw \
action mirred ingress mirror dev eth1 skip_sw
where the offload flags coincide, and this should be treated the same as
the first command based on inheritance, and accepted.
[1]: https://lore.kernel.org/netdev/20211028110646.13791-9-simon.horman@corigine.com/
[2]: https://lore.kernel.org/netdev/20211118130805.23897-10-simon.horman@corigine.com/
Fixes: 7adc576512 ("flow_offload: add skip_hw and skip_sw to control if offload the action")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20241017161049.3570037-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The fix for MAC addresses broke detection of the naming convention
because it gave network devices no random MAC before bind()
was called. This means that the check for the local assignment bit
was always negative as the address was zeroed from allocation,
instead of from overwriting the MAC with a unique hardware address.
The correct check for whether bind() has altered the MAC is
done with is_zero_ether_addr
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Greg Thelen <gthelen@google.com>
Diagnosed-by: John Sperbeck <jsperbeck@google.com>
Fixes: bab8eb0dd4 ("usbnet: modern method to get random MAC")
Link: https://patch.msgid.link/20241017071849.389636-1-oneukum@suse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is meant to use xa_err() to extract the error encoded in the return
value of xa_store().
Fixes: 44c2fbebe1 ("mlxsw: spectrum_router: Share nexthop counters in resilient groups")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20241017023223.74180-1-yuancan@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=cTcY
-----END PGP SIGNATURE-----
Merge tag 'nf-24-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
This patchset contains Netfilter fixes for net:
1) syzkaller managed to triger UaF due to missing reference on netns in
bpf infrastructure, from Florian Westphal.
2) Fix incorrect conversion from NFPROTO_UNSPEC to NFPROTO_{IPV4,IPV6}
in the following xtables targets: MARK and NFLOG. Moreover, add
missing
I have my half share in this mistake, I did not take the necessary time
to review this: For several years I have been struggling to keep working
on Netfilter, juggling a myriad of side consulting projects to stop
burning my own savings.
I have extended the iptables-tests.py test infrastructure to improve the
coverage of ip6tables and detect similar problems in the future.
This is a v2 including a extended PR with one more fix.
netfilter pull request 24-10-21
* tag 'nf-24-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: xtables: fix typo causing some targets not to load on IPv6
netfilter: bpf: must hold reference on net namespace
====================
Link: https://patch.msgid.link/20241021094536.81487-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Static analysis on linux-next has detected the following issue
in function virtnet_stats_ctx_init, in drivers/net/virtio_net.c :
if (vi->device_stats_cap & VIRTIO_NET_STATS_TYPE_CVQ) {
queue_type = VIRTNET_Q_TYPE_CQ;
ctx->bitmap[queue_type] |= VIRTIO_NET_STATS_TYPE_CVQ;
ctx->desc_num[queue_type] += ARRAY_SIZE(virtnet_stats_cvq_desc);
ctx->size[queue_type] += sizeof(struct virtio_net_stats_cvq);
}
ctx->bitmap is declared as a u32 however it is being bit-wise or'd with
VIRTIO_NET_STATS_TYPE_CVQ and this is defined as 1 << 32:
include/uapi/linux/virtio_net.h:#define VIRTIO_NET_STATS_TYPE_CVQ (1ULL << 32)
..and hence the bit-wise or operation won't set any bits in ctx->bitmap
because 1ULL < 32 is too wide for a u32.
In fact, the field is read into a u64:
u64 offset, bitmap;
....
bitmap = ctx->bitmap[queue_type];
so to fix, it is enough to make bitmap an array of u64.
Fixes: 941168f8b4 ("virtio_net: support device stats")
Reported-by: "Colin King (gmail)" <colin.i.king@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/53e2bd6728136d5916e384a7840e5dc7eebff832.1729099611.git.mst@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some workloads hit the infamous dev_watchdog() message:
"NETDEV WATCHDOG: eth0 (xxxx): transmit queue XX timed out"
It seems possible to hit this even for perfectly normal
BQL enabled drivers:
1) Assume a TX queue was idle for more than dev->watchdog_timeo
(5 seconds unless changed by the driver)
2) Assume a big packet is sent, exceeding current BQL limit.
3) Driver ndo_start_xmit() puts the packet in TX ring,
and netdev_tx_sent_queue() is called.
4) QUEUE_STATE_STACK_XOFF could be set from netdev_tx_sent_queue()
before txq->trans_start has been written.
5) txq->trans_start is written later, from netdev_start_xmit()
if (rc == NETDEV_TX_OK)
txq_trans_update(txq)
dev_watchdog() running on another cpu could read the old
txq->trans_start, and then see QUEUE_STATE_STACK_XOFF, because 5)
did not happen yet.
To solve the issue, write txq->trans_start right before one XOFF bit
is set :
- _QUEUE_STATE_DRV_XOFF from netif_tx_stop_queue()
- __QUEUE_STATE_STACK_XOFF from netdev_tx_sent_queue()
From dev_watchdog(), we have to read txq->state before txq->trans_start.
Add memory barriers to enforce correct ordering.
In the future, we could avoid writing over txq->trans_start for normal
operations, and rename this field to txq->xoff_start_time.
Fixes: bec251bc8b ("net: no longer stop all TX queues in dev_watchdog()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://patch.msgid.link/20241015194118.3951657-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- There is no NFPROTO_IPV6 family for mark and NFLOG.
- TRACE is also missing module autoload with NFPROTO_IPV6.
This results in ip6tables failing to restore a ruleset. This issue has been
reported by several users providing incomplete patches.
Very similar to Ilya Katsnelson's patch including a missing chunk in the
TRACE extension.
Fixes: 0bfcb7b71e ("netfilter: xtables: avoid NFPROTO_UNSPEC where needed")
Reported-by: Ignat Korchagin <ignat@cloudflare.com>
Reported-by: Ilya Katsnelson <me@0upti.me>
Reported-by: Krzysztof Olędzki <ole@ans.pl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Aleksandr Mishin says:
====================
fsl/fman: Fix refcount handling of fman-related devices
The series is intended to fix refcount handling for fman-related "struct
device" objects - the devices are not released upon driver removal or in
the error paths during probe. This leads to device reference leaks.
The device pointers are now saved to struct mac_device and properly handled
in the driver's probe and removal functions.
Originally reported by Simon Horman <horms@kernel.org>
(https://lore.kernel.org/all/20240702133651.GK598357@kernel.org/)
Compile tested only.
====================
Link: https://patch.msgid.link/20241015060122.25709-1-amishin@t-argos.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In mac_probe() there are multiple calls to of_find_device_by_node(),
fman_bind() and fman_port_bind() which takes references to of_dev->dev.
Not all references taken by these calls are released later on error path
in mac_probe() and in mac_remove() which lead to reference leaks.
Add references release.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In mac_probe() there are calls to of_find_device_by_node() which takes
references to of_dev->dev. These references are not saved and not released
later on error path in mac_probe() and in mac_remove().
Add new fields into mac_device structure to save references taken for
future use in mac_probe() and mac_remove().
This is a preparation for further reference leaks fix.
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
samples/pktgen is missing in the MAINTAINERS file.
Suggested-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Message-ID: <20241018005301.10052-1-liuhangbin@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Mapping all my previously used emails to my kernel.org email.
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Message-ID: <172909057364.2452383.8019986488234344607.stgit@firesoul>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
mv88e6393x_port_set_policy doesn't correctly shift the ptr value when
converting the policy format between the old and new styles, so the
target register ends up with the ptr being written over the data bits.
Shift the pointer to align with the format expected by
mv88e6393x_port_policy_write().
Fixes: 6584b26020 ("net: dsa: mv88e6xxx: implement .port_set_policy for Amethyst")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016040822.3917-1-peter@rashleigh.ca>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
build_skb() returns NULL in case of a memory allocation failure so handle
it inside __octep_oq_process_rx() to avoid NULL pointer dereference.
__octep_oq_process_rx() is called during NAPI polling by the driver. If
skb allocation fails, keep on pulling packets out of the Rx DMA queue: we
shouldn't break the polling immediately and thus falsely indicate to the
octep_napi_poll() that the Rx pressure is going down. As there is no
associated skb in this case, don't process the packets and don't push them
up the network stack - they are skipped.
Helper function is implemented to unmmap/flush all the fragment buffers
used by the dropped packet. 'alloc_failures' counter is incremented to
mark the skb allocation error in driver statistics.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 37d79d0596 ("octeon_ep: add Tx/Rx processing and interrupt support")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The common code with some packet and index manipulations is extracted and
moved to newly implemented helper to make the code more readable and avoid
duplication. This is a preparation for skb allocation failure handling.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Suggested-by: Simon Horman <horms@kernel.org>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
In netpoll configuration the completion processing can happen in hard
irq context which will break with spin_lock_bh() for fullfilling RX
timestamp in case of all packets timestamping. Replace it with
spin_lock_irqsave() variant.
Fixes: 7f5515d19c ("bnxt_en: Get the RX packet timestamp")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Message-ID: <20241016195234.2622004-1-vadfed@meta.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This change fixes a rare issue where the PHY fails to detect a link
due to incorrect reset behavior.
The SW_RESET definition was incorrectly assigned to bit 14, which is the
Digital Restart bit according to the datasheet. This commit corrects
SW_RESET to bit 15 and assigns DIG_RESTART to bit 14 as per the
datasheet specifications.
The SW_RESET define is only used in the phy_reset function, which fully
re-initializes the PHY after the reset is performed. The change in the
bit definitions should not have any negative impact on the functionality
of the PHY.
v2:
- added Fixes tag
- improved commit message
Cc: stable@vger.kernel.org
Fixes: 5dc39fd5ef ("net: phy: DP83822: Add ability to advertise Fiber connection")
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Message-ID: <AS1P250MB0608A798661549BF83C4B43EA9462@AS1P250MB0608.EURP250.PROD.OUTLOOK.COM>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Simon has been diligently and consistently reviewing networking
changes for at least as long as our development statistics
go back. Often if not usually topping the list of reviewers.
Make his role official.
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241015153005.2854018-1-kuba@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Since commit
71ae2cb305 ("net: plip: Fix fall-through warnings for Clang")
plip was not able to send any packets, this patch replaces one
unintended break; with fallthrough; which was originally missed by
commit 9525d69a36 ("net: plip: mark expected switch fall-throughs").
I have verified with a real hardware PLIP connection that everything
works once again after applying this patch.
Fixes: 71ae2cb305 ("net: plip: Fix fall-through warnings for Clang")
Signed-off-by: Jakub Boehm <boehm.jakub@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241015-net-plip-tx-fix-v1-1-32d8be1c7e0b@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The be_xmit() returns NETDEV_TX_OK without freeing skb
in case of be_xmit_enqueue() fails, add dev_kfree_skb_any() to fix it.
Fixes: 760c295e0e ("be2net: Support for OS2BMC.")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Message-ID: <20241015144802.12150-1-wanghai38@huawei.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The sun3_82586_send_packet() returns NETDEV_TX_OK without freeing skb
in case of skb->len being too long, add dev_kfree_skb() to fix it.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241015144148.7918-1-wanghai38@huawei.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Adjust the loop limit to prevent out-of-bounds access when iterating over
PI structures. The loop should not reach the index pcdev->nr_lines since
we allocate exactly pcdev->nr_lines number of PI structures. This fix
ensures proper bounds are maintained during iterations.
Fixes: 9be9567a7c ("net: pse-pd: Add support for PSE PIs")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Message-ID: <20241015130255.125508-1-kory.maincent@bootlin.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Current release - new code bugs:
- eth: mlx5: HWS, don't destroy more bwc queue locks than allocated
Previous releases - regressions:
- ipv4: give an IPv4 dev to blackhole_netdev
- udp: compute L4 checksum as usual when not segmenting the skb
- tcp/dccp: don't use timer_pending() in reqsk_queue_unlink().
- eth: mlx5e: don't call cleanup on profile rollback failure
- eth: microchip: vcap api: fix memory leaks in vcap_api_encode_rule_test()
- eth: enetc: disable Tx BD rings after they are empty
- eth: macb: avoid 20s boot delay by skipping MDIO bus registration for fixed-link PHY
Previous releases - always broken:
- posix-clock: fix missing timespec64 check in pc_clock_settime()
- genetlink: hold RCU in genlmsg_mcast()
- mptcp: prevent MPC handshake on port-based signal endpoints
- eth: vmxnet3: fix packet corruption in vmxnet3_xdp_xmit_frame
- eth: stmmac: dwmac-tegra: fix link bring-up sequence
- eth: bcmasp: fix potential memory leak in bcmasp_xmit()
Misc:
- add Andrew Lunn as a co-maintainer of all networking drivers
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=ukTi
-----END PGP SIGNATURE-----
Merge tag 'net-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Current release - new code bugs:
- eth: mlx5: HWS, don't destroy more bwc queue locks than allocated
Previous releases - regressions:
- ipv4: give an IPv4 dev to blackhole_netdev
- udp: compute L4 checksum as usual when not segmenting the skb
- tcp/dccp: don't use timer_pending() in reqsk_queue_unlink().
- eth: mlx5e: don't call cleanup on profile rollback failure
- eth: microchip: vcap api: fix memory leaks in
vcap_api_encode_rule_test()
- eth: enetc: disable Tx BD rings after they are empty
- eth: macb: avoid 20s boot delay by skipping MDIO bus registration
for fixed-link PHY
Previous releases - always broken:
- posix-clock: fix missing timespec64 check in pc_clock_settime()
- genetlink: hold RCU in genlmsg_mcast()
- mptcp: prevent MPC handshake on port-based signal endpoints
- eth: vmxnet3: fix packet corruption in vmxnet3_xdp_xmit_frame
- eth: stmmac: dwmac-tegra: fix link bring-up sequence
- eth: bcmasp: fix potential memory leak in bcmasp_xmit()
Misc:
- add Andrew Lunn as a co-maintainer of all networking drivers"
* tag 'net-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
net/mlx5e: Don't call cleanup on profile rollback failure
net/mlx5: Unregister notifier on eswitch init failure
net/mlx5: Fix command bitmask initialization
net/mlx5: Check for invalid vector index on EQ creation
net/mlx5: HWS, use lock classes for bwc locks
net/mlx5: HWS, don't destroy more bwc queue locks than allocated
net/mlx5: HWS, fixed double free in error flow of definer layout
net/mlx5: HWS, removed wrong access to a number of rules variable
mptcp: pm: fix UaF read in mptcp_pm_nl_rm_addr_or_subflow
net: ethernet: mtk_eth_soc: fix memory corruption during fq dma init
vmxnet3: Fix packet corruption in vmxnet3_xdp_xmit_frame
net: dsa: vsc73xx: fix reception from VLAN-unaware bridges
net: ravb: Only advertise Rx/Tx timestamps if hardware supports it
net: microchip: vcap api: Fix memory leaks in vcap_api_encode_rule_test()
net: phy: mdio-bcm-unimac: Add BCM6846 support
dt-bindings: net: brcm,unimac-mdio: Add bcm6846-mdio
udp: Compute L4 checksum as usual when not segmenting the skb
genetlink: hold RCU in genlmsg_mcast()
net: dsa: mv88e6xxx: Fix the max_vid definition for the MV88E6361
tcp/dccp: Don't use timer_pending() in reqsk_queue_unlink().
...
BUG: KASAN: slab-use-after-free in __nf_unregister_net_hook+0x640/0x6b0
Read of size 8 at addr ffff8880106fe400 by task repro/72=
bpf_nf_link_release+0xda/0x1e0
bpf_link_free+0x139/0x2d0
bpf_link_release+0x68/0x80
__fput+0x414/0xb60
Eric says:
It seems that bpf was able to defer the __nf_unregister_net_hook()
after exit()/close() time.
Perhaps a netns reference is missing, because the netns has been
dismantled/freed already.
bpf_nf_link_attach() does :
link->net = net;
But I do not see a reference being taken on net.
Add such a reference and release it after hook unreg.
Note that I was unable to get syzbot reproducer to work, so I
do not know if this resolves this splat.
Fixes: 84601d6ee6 ("bpf: add bpf_link support for BPF_NETFILTER programs")
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Reported-by: Lai, Yi <yi1.lai@linux.intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tariq Toukan says:
====================
mlx5 misc fixes 2024-10-15
This patchset provides misc bug fixes from the team to the mlx5 core and
Eth drivers.
Series generated against:
commit 174714f0e5 ("selftests: drivers: net: fix name not defined")
====================
Link: https://patch.msgid.link/20241015093208.197603-1-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Command bitmask have a dedicated bit for MANAGE_PAGES command, this bit
isn't Initialize during command bitmask Initialization, only during
MANAGE_PAGES.
In addition, mlx5_cmd_trigger_completions() is trying to trigger
completion for MANAGE_PAGES command as well.
Hence, in case health error occurred before any MANAGE_PAGES command
have been invoke (for example, during mlx5_enable_hca()),
mlx5_cmd_trigger_completions() will try to trigger completion for
MANAGE_PAGES command, which will result in null-ptr-deref error.[1]
Fix it by Initialize command bitmask correctly.
While at it, re-write the code for better understanding.
[1]
BUG: KASAN: null-ptr-deref in mlx5_cmd_trigger_completions+0x1db/0x600 [mlx5_core]
Write of size 4 at addr 0000000000000214 by task kworker/u96:2/12078
CPU: 10 PID: 12078 Comm: kworker/u96:2 Not tainted 6.9.0-rc2_for_upstream_debug_2024_04_07_19_01 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_health0000:08:00.0 mlx5_fw_fatal_reporter_err_work [mlx5_core]
Call Trace:
<TASK>
dump_stack_lvl+0x7e/0xc0
kasan_report+0xb9/0xf0
kasan_check_range+0xec/0x190
mlx5_cmd_trigger_completions+0x1db/0x600 [mlx5_core]
mlx5_cmd_flush+0x94/0x240 [mlx5_core]
enter_error_state+0x6c/0xd0 [mlx5_core]
mlx5_fw_fatal_reporter_err_work+0xf3/0x480 [mlx5_core]
process_one_work+0x787/0x1490
? lockdep_hardirqs_on_prepare+0x400/0x400
? pwq_dec_nr_in_flight+0xda0/0xda0
? assign_work+0x168/0x240
worker_thread+0x586/0xd30
? rescuer_thread+0xae0/0xae0
kthread+0x2df/0x3b0
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x2d/0x70
? kthread_complete_and_exit+0x20/0x20
ret_from_fork_asm+0x11/0x20
</TASK>
Fixes: 9b98d395b8 ("net/mlx5: Start health poll at earlier stage of driver load")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, mlx5 driver does not enforce vector index to be lower than
the maximum number of supported completion vectors when requesting a
new completion EQ. Thus, mlx5_comp_eqn_get() fails when trying to
acquire an IRQ with an improper vector index.
To prevent the case above, enforce that vector index value is
valid and lower than maximum in mlx5_comp_eqn_get() before handling the
request.
Fixes: f14c1a14e6 ("net/mlx5: Allocate completion EQs dynamically")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The HWS BWC API uses one lock per queue and usually acquires one of
them, except when doing changes which require locking all queues in
order. Naturally, lockdep isn't too happy about acquiring the same lock
class multiple times, so inform it that each queue lock is a different
class to avoid false positives.
Fixes: 2ca62599aa ("net/mlx5: HWS, added send engine and context handling")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
hws_send_queues_bwc_locks_destroy destroyed more queue locks than
allocated, leading to memory corruption (occasionally) and warnings such
as DEBUG_LOCKS_WARN_ON(mutex_is_locked(lock)) in __mutex_destroy because
sometimes, the 'mutex' being destroyed was random memory.
The severity of this problem is proportional to the number of queues
configured because the code overreaches beyond the end of the
bwc_send_queue_locks array by 2x its length.
Fix that by using the correct number of bwc queues.
Fixes: 2ca62599aa ("net/mlx5: HWS, added send engine and context handling")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix error flow bug that could lead to double free of a buffer
during a failure to calculate a suitable definer layout.
Fixes: 74a778b4a6 ("net/mlx5: HWS, added definers handling")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Removed wrong access to the num_of_rules field of the matcher.
This is a usual u32 variable, but the access was as if it was atomic.
This fixes the following CI warnings:
mlx5hws_bwc.c:708:17: warning: large atomic operation may incur significant performance penalty;
the access size (4 bytes) exceeds the max lock-free size (0 bytes) [-Watomic-alignment]
Fixes: 510f9f61a1 ("net/mlx5: HWS, added API and enabled HWS support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409291101.6NdtMFVC-lkp@intel.com/
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
