airoha_tc_htb_alloc_leaf_queue() assigns queue IDs based on the channel
index (opt->qid = AIROHA_NUM_TX_RING + channel), but updates
real_num_tx_queues with a simple increment (num_tx_queues + 1). When QoS
channels are allocated sparsely (e.g., channels 0 and 3 without 1 and
2), the returned qid can exceed real_num_tx_queues, causing out-of-bounds
accesses in the networking stack.
For example, allocating channel 0 then channel 3 results in
real_num_tx_queues = 34 but qid = 35, which is out of range [0, 34).
Fix this by computing real_num_tx_queues based on the highest active
channel index rather than using a simple counter, in both the allocation
and deletion paths.
Fixes: ef1ca92713 ("net: airoha: Add sched HTB offload support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260619-airoha-qos-fixes-v2-2-5c43485038f9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
airoha_tc_htb_alloc_leaf_queue() computes the HTB QoS channel index
as opt->classid % AIROHA_NUM_QOS_CHANNELS and stores it in qos_sq_bmap.
However, airoha_tc_remove_htb_queue() clears the HTB configuration
using queue + 1 as the channel index, causing an off-by-one error.
Use queue directly as the QoS channel index to match the allocation
logic.
Fixes: ef1ca92713 ("net: airoha: Add sched HTB offload support")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260619-airoha-qos-fixes-v2-1-5c43485038f9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When requesting ownership of the NIC (MAC/PHY control), we set up
the heartbeat to look stale:
/* Initialize heartbeat, set last response to 1 second in the past
* so that we will trigger a timeout if the firmware doesn't respond
*/
fbd->last_heartbeat_response = req_time - HZ;
fbd->last_heartbeat_request = req_time;
The response handler then sets:
fbd->last_heartbeat_response = jiffies;
for which we wait via:
fbnic_fw_init_heartbeat() -> fbnic_fw_heartbeat_current()
The scheme is a bit odd, but it should work in principle.
Fix the ordering of operations. We have to set up the stale heartbeat
before we send the message. Otherwise if the response is very fast
we will override it. This triggers on QEMU if we run on the core
that handles the IRQ, and results in ndo_open failing with ETIMEDOUT.
The change in ordering doesn't impact releasing the ownership.
Both ndo_stop and heartbeat check are under rtnl_lock.
Fixes: 20d2e88cc7 ("eth: fbnic: Add initial messaging to notify FW of our presence")
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260622154753.827506-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fernando Fernandez Mancera says:
====================
ipv6: fix error handling in disable_ipv6 sysctl
While working on a different IPv6 patch series I have spotted multiple
minor bugs around sysctl error handling and notifications. In general,
they are not serious issues.
In addition, there is one more issue in forwarding sysctl as it does not
check for CAP_NET_ADMIN for the namespace. I am keeping that patch out
of this series and I am aiming it at the net-next tree once it re-opens.
During v3, Ido's pointed out that it is unnecessary to reset the
position pointer when the return value is negative as at
new_sync_write() the ppos is only advanced when ret return value is
positive. That means we can get rid of that operation in ipv4/ipv6
sysctls. That is going to be sent to net-next too.
====================
Link: https://patch.msgid.link/20260622130857.5115-1-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When changing the ignore_routes_with_linkdown sysctl for a specific
interface, the RTM_NEWNETCONF netlink notification was not being emitted
to userspace. Fix this by emitting the notification when needed.
In addition, fix bogus return value for successful "all" and specific
interface write operation leading to a wrong reset of the position
pointer.
Fixes: 35103d1117 ("net: ipv6 sysctl option to ignore routes when nexthop link is down")
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260622130857.5115-7-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When handling proxy_ndp, if rtnl_net_trylock() fails, the operation is
retried but as the value was already modified by the initial
proc_dointvec() call, the restarted syscall will read the newly modified
value as the 'old' state.
Fix this by taking the RTNL lock before parsing the input value if the
operation is a write.
Fixes: c92d5491a6 ("netconf: add support for IPv6 proxy_ndp")
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260622130857.5115-6-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When writing to the disable_policy sysctl, if proc_dointvec() fails to
parse the input, it returns a negative error code. The current
implementation is resetting the position argument even if an error
occurred during proc_dointvec() and not only during sysctl restart.
Fix this by checking the return value of proc_dointvec() and returning
early on failure.
Fixes: df789fe752 ("ipv6: Provide ipv6 version of "disable_policy" sysctl")
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260622130857.5115-5-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When writing to the forwarding sysctl, if proc_dointvec() fails to parse
the input, it returns a negative error code. The current implementation
is overwriting that error for write operations.
This results in a silent failure, it returns a successful write although
the configuration was not modified at all. When modifying the "all"
variant it can also modify the configuration of existing interfaces to
the wrong value.
Fix this by checking the return value of proc_dointvec() and returning
early on failure. In addition, adjust return code of
addrconf_fixup_forwarding() for successful operation.
Fixes: b325fddb7f ("ipv6: Fix sysctl unregistration deadlock")
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260622130857.5115-4-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When writing to the ignore_routes_with_linkdown sysctl, if
proc_dointvec() fails to parse the input, it returns a negative error
code. The current implementation is overwriting that error for write
operations.
This results in a silent failure, it returns a successful write although
the configuration was not modified at all. When modifying the "all"
variant it can also modify the configuration of existing interfaces to
the wrong value.
Fix this by checking the return value of proc_dointvec() and returning
early on failure.
Fixes: 35103d1117 ("net: ipv6 sysctl option to ignore routes when nexthop link is down")
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260622130857.5115-3-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When writing to the disable_ipv6 sysctl, if proc_dointvec() fails to
parse the input, it returns a negative error code. The current
implementation is overwriting that error for write operations.
This results in a silent failure, it returns a successful write although
the configuration was not modified at all. When modifying the "all"
variant it can also modify the configuration of existing interfaces to
the wrong value.
Fix this by checking the return value of proc_dointvec() and returning
early on failure.
Fixes: 56d417b12e ("IPv6: Add 'autoconf' and 'disable_ipv6' module parameters")
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260622130857.5115-2-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I have left Sunplus and no longer have access to the relevant hardware
to test or maintain this driver. Mark the driver as orphaned.
Signed-off-by: Wells Lu <wellslutw@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260622180721.28334-1-wellslutw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
au1000_close() calls free_irq() while aup->lock is still held with
spin_lock_irqsave(). free_irq() can sleep because it takes the IRQ
descriptor request mutex, so it does not belong inside the close-time
spinlocked section.
This was found by our static analysis tool and then confirmed by manual
review of the in-tree au1000_close() .ndo_stop path. The reviewed path
keeps aup->lock held across the MAC reset, queue stop and
free_irq(dev->irq, dev).
A directed runtime validation kept that ndo_stop carrier and the same
free_irq(dev->irq, dev) operation under the driver lock. Lockdep reported
"BUG: sleeping function called from invalid context" and "Invalid wait
context" while free_irq() was taking desc->request_mutex, with
au1000_close() and free_irq() on the stack.
Drop aup->lock before freeing the IRQ. The protected close-time work still
stops the device and queue before IRQ teardown, but the sleepable IRQ core
path now runs outside the spinlocked section.
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260619151816.1144289-1-runyu.xiao@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When sctp_verify_init() encounters unrecognized parameters, it allocates an
err_chunk to report them. However, this chunk is leaked in several code
paths:
1. In sctp_sf_do_5_1B_init(), if security_sctp_assoc_request() fails after
sctp_verify_init() has populated err_chunk, the function returns
immediately without freeing it.
2. In sctp_sf_do_unexpected_init(), the same leak occurs on the
security_sctp_assoc_request() failure path.
3. In sctp_sf_do_unexpected_init(), on the success path after copying
unrecognized parameters to the INIT-ACK, the function returns without
freeing err_chunk, unlike sctp_sf_do_5_1B_init() which properly frees
it.
Fix all three leaks by adding sctp_chunk_free(err_chunk) calls before
returning in the error paths and on the success path in
sctp_sf_do_unexpected_init().
Fixes: c081d53f97 ("security: pass asoc to sctp_assoc_request and sctp_sk_clone")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/0656704f1b0158287c98aec09ba36c83e4a537ab.1781970534.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcf_classify() can return TC_ACT_CONSUMED while the skb is held by the
defragmentation engine (e.g. act_ct on out-of-order fragments). When
that happens the skb is no longer owned by the caller and must not be
touched again.
tcf_qevent_handle() did not handle TC_ACT_CONSUMED: it fell through the
switch and returned the skb to the caller as if classification had
passed. The only qdisc that wires up qevents today is RED, via three call sites
(qe_mark on RED_PROB_MARK/HARD_MARK, qe_early_drop on congestion_drop)
red_enqueue() was continuing to operate on an skb it no longer owns in this
case -- enqueueing it, dropping it, or updating statistics. Resulting in a UAF.
tc qdisc add dev eth0 root handle 1: red ... qevent early_drop block 10
tc filter add block 10 ... action ct
(with ct defrag enabled and traffic that produces out-of-order
fragments, e.g. a fragmented UDP stream)
Handle TC_ACT_CONSUMED in tcf_qevent_handle() the same way the ingress
and egress fast paths do: treat it as stolen and return NULL without
touching the skb. Unlike the TC_ACT_STOLEN case, the skb must not be
dropped/freed here, as it is no longer owned by us.
Fixes: 3f14b377d0 ("net/sched: act_ct: fix skb leak and crash on ooo frags")
Reported-by: Zero Day Initiative <zdi-disclosures@trendmicro.com>
Tested-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260620130749.226642-1-jhs@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that an LWT encapsulation does not silently corrupt XDP metadata
sitting in the skb headroom. Exercise all three LWT dispatch paths:
- BPF LWT xmit prog reserves headroom on the LWT .xmit redirect,
- mpls pushes an MPLS label on the LWT .xmit redirect,
- seg6 in encap mode runs on the LWT .input redirect,
- ioam6 encap inserts an IOAM Hop-by-Hop option on LWT .output redirect.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://patch.msgid.link/20260619-bpf-lwt-drop-skb-metadata-v3-2-71d6a33ab76b@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
skb metadata is meant for passing information between XDP and TC. It lives
in the skb headroom, immediately before skb->data. LWT programs cannot
access the __sk_buff->data_meta pseudo-pointer to metadata.
However, LWT encapsulation prepends outer headers, moving skb->data back
over the headroom where the metadata sits. On an RX-originated (forwarded)
packet that still carries XDP metadata this goes wrong in two different
ways, depending on the encap type:
1. Non-BPF LWT encaps (mpls, seg6, ioam6 ...) call skb_push()/skb_pull()
and silently overwrite the metadata that sits in the headroom.
2) BPF LWT xmit calls bpf_skb_change_head(), which uses skb_data_move().
That helper expects metadata immediately before skb->data. But since
the IP output path runs LWT xmit before neighbour output has built
the outgoing L2 header, for forwarded packets skb->data points at the
L3 header while skb_mac_header() still points at the old L2 header.
skb_data_move() sees metadata ending at skb_mac_header(), not before
skb->data, warns and clears metadata:
WARNING: CPU: 21 PID: 454557 at include/linux/skbuff.h:4609 skb_data_move+0x47/0x90
CPU: 21 UID: 0 PID: 454557 Comm: napi/iconduit-g Tainted: G O 6.18.21 #1
RIP: 0010:skb_data_move+0x47/0x90
Call Trace:
<IRQ>
bpf_skb_change_head+0xe6/0x1a0
bpf_prog_...+0x213/0x2e3
run_lwt_bpf.isra.0+0x1d3/0x360
bpf_xmit+0x46/0xe0
lwtunnel_xmit+0xa1/0xf0
ip_finish_output2+0x1e7/0x5e0
ip_output+0x63/0x100
__netif_receive_skb_one_core+0x85/0xa0
process_backlog+0x9c/0x150
__napi_poll+0x2b/0x190
net_rx_action+0x40b/0x7f0
handle_softirqs+0xd2/0x270
do_softirq+0x3f/0x60
</IRQ>
That is what happens, as for how to fix it - a received packet that
carries metadata can reach an encap through any of the three LWT
redirect modes:
LWTUNNEL_STATE_INPUT_REDIRECT
ip6_rcv_finish
dst_input
lwtunnel_input
LWTUNNEL_STATE_OUTPUT_REDIRECT
ip6_rcv_finish
dst_input
ip6_forward
ip6_forward_finish
dst_output
lwtunnel_output
LWTUNNEL_STATE_XMIT_REDIRECT
ip6_rcv_finish
dst_input
ip6_forward
ip6_forward_finish
dst_output
ip6_output
ip6_finish_output
ip6_finish_output2
lwtunnel_xmit
Every encap funnels through the three LWT dispatch helpers, so drop the
metadata there, right before handing the skb to the encap op. This
single chokepoint covers all encap types and all three redirect modes:
- lwtunnel_input(): seg6, rpl, ila, seg6_local
- lwtunnel_output(): ioam6
- lwtunnel_xmit(): mpls, LWT BPF xmit
Alternatively, we could clear the metadata right after TC ingress hook.
That would require a compromise, however. Metadata would become
inaccessible from TC egress (in setups where it actually reaches the
hook it tact, that is without any L2 tunnels on path).
Fixes: 8989d328df ("net: Helper to move packet data and metadata after skb_push/pull")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://patch.msgid.link/20260619-bpf-lwt-drop-skb-metadata-v3-1-71d6a33ab76b@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LFlA
-----END PGP SIGNATURE-----
Merge tag 'ipsec-2026-06-22' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2026-06-22
1) xfrm: use compat translator only for u64 alignment mismatch
Gate the XFRM_USER_COMPAT translator on COMPAT_FOR_U64_ALIGNMENT
so 32-bit compat tasks on arches whose 32-bit ABI already matches
the native 64-bit layout are no longer rejected with -EOPNOTSUPP.
From Sanman Pradhan.
2) net: af_key: initialize alg_key_len for IPComp states
Initialize the alg_key_len to 0 in the IPComp branch of
pfkey_msg2xfrm_state() so an uninitialized value cannot drive
xfrm_alg_len() into a slab-out-of-bounds kmemdup during
XFRM_MSG_MIGRATE. From Zijing Yin.
3) xfrm: Fix dev use-after-free in xfrm async resumption
Stash the original skb->dev and extend the RCU critical section
across xfrm_rcv_cb() and transport_finish() to prevent a
tunnel-device UAF and original-device refcount leak when a
callback replaces skb->dev. From Dong Chenchen.
4) xfrm: Fix xfrm state cache insertion race
Move the state-validity check inside xfrm_state_lock in the
input state cache insertion path so a state cannot be killed
between the check and the insert. From Herbert Xu.
5) xfrm: annotate data-races around xfrm_policy_count[] and xfrm_policy_default[]
Add READ_ONCE()/WRITE_ONCE() annotations on xfrm_policy_count
and xfrm_policy_default to silence the KCSAN data race reported
on net->xfrm.policy_count. From Eric Dumazet.
6) espintcp: use sk_msg_free_partial to fix partial send
Replace the manual skmsg accounting in espintcp with
sk_msg_free_partial() so the skmsg stays consistent on every
iteration and the partial-send accounting bugs go away.
From Sabrina Dubroca.
7) xfrm: validate selector family and prefixlen during match
Reject mismatched address families in xfrm_selector_match() and
bound prefixlen in addr4_match()/addr_match() to prevent the
shift-out-of-bounds syzbot reported when an AF_UNSPEC selector
with a large prefixlen is matched against an IPv4 flow.
From Eric Dumazet.
* tag 'ipsec-2026-06-22' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: validate selector family and prefixlen during match
espintcp: use sk_msg_free_partial to fix partial send
xfrm: annotate data-races around xfrm_policy_count[] and xfrm_policy_default[]
xfrm: Fix xfrm state cache insertion race
xfrm: Fix dev use-after-free in xfrm async resumption
net: af_key: initialize alg_key_len for IPComp states
xfrm: use compat translator only for u64 alignment mismatch
====================
Link: https://patch.msgid.link/20260622075726.29685-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Configured VLANs intermittently stop receiving traffic after a link
down/up cycle, e.g. when the network cable is unplugged and plugged back
in. VLAN filtering stays enabled but all VLAN-tagged frames are dropped
until a VLAN is added or removed again.
The LAN7801 datasheet (DS00002123E) states:
"A portion of the MAC operates on clocks generated by the Ethernet
PHY. During a PHY reset event, this portion of the MAC is designed to
not be taken out of reset until the PHY clocks are operational"
(section 8.10, MAC Reset Watchdog Timer)
"After a reset event, the RFE will automatically initialize the
contents of the VHF to 0h."
(section 7.1.4, VHF Organization)
Thus a link down/up cycle stops and restarts the PHY clock, resets the
PHY-clocked portion of the MAC, and the RFE clears its VLAN/DA hash
filter (VHF) memory. The VHF holds both the VLAN filter table and the
multicast hash table, but the driver never reprograms either from its
shadow copy once the link is back, so both stay empty.
Reprogram the VLAN filter and multicast hash tables on link up.
Reported-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Closes: https://lore.kernel.org/netdev/BEZP281MB224501E38B30BFDC4BD3D364D9E32@BEZP281MB2245.DEUP281.PROD.OUTLOOK.COM/T/#u
Tested-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260622102911.484045-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During XDP enablement in veth, if xdp_rxq_info_reg() or
xdp_rxq_info_reg_mem_model() fails, the driver rolls back the changes.
However, the rollback loop:
for (i--; i >= start; i--) {
decrements the loop index 'i' before the first iteration. This
correctly skips unregistering the rxq for the failed index 'i' (as
registration failed or was already cleaned up), but it also
erroneously skips calling netif_napi_deli() for rq[i].xdp_napi.
Since netif_napi_add() was already called for index 'i', this leaves
a dangling napi_struct in the device's napi_list. When the veth
device is later destroyed, the freed queue memory (which contains the
leaked NAPI structure) can be reused.
The subsequent device teardown iterates the NAPI list and
corrupts the reallocated memory, leading to UAF.
Fix this by explicitly deleting the NAPI association for the failed
index 'i' before rolling back the successfully configured queues.
Fixes: b02e5a0ebb ("xsk: Propagate napi_id to XDP socket Rx path")
Reported-by: Guenter Roeck <groeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260622111825.88337-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
emac_xsk_xmit_zc() handles tx xmit for zero copy and gets called
inside napi context. User application wakes up the kernel while
initiating the transmit which triggers napi to start processing
the tx packets. The num_tx check inside emac_tx_complete_packets()
returns early if no packet transfer happen hindering the call
to emac_xsk_xmit_zc(). Remove this check to let application
wakeup initiate zero copy xmit traffic.
Add __netif_tx_lock() to ensure that the TX queue is protected
from concurrent access during the transmission of XDP frames.
This fixes netdev watchdog timeout for long runs.
Fixes: e2dc7bfd67 ("net: ti: icssg-prueth: Move common functions into a separate file")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Link: https://patch.msgid.link/20260618100348.2209907-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pin_duration is converted from the user-provided period to SJA1105
clock ticks and is later passed as the cycle_time argument to
future_base_time().
Very small period values may become zero after the conversion,
which can lead to a division by zero in future_base_time().
Round zero pin_duration up to 1 tick so that the smallest unsupported
periods use the minimum non-zero hardware duration instead of passing
zero to future_base_time().
Fixes: 747e5eb31d ("net: dsa: sja1105: configure the PTP_CLK pin as EXT_TS or PER_OUT")
Signed-off-by: Aleksandrova Alyona <aga@itb.spb.ru>
Link: https://patch.msgid.link/20260618110508.53094-1-aga@itb.spb.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marek Szyprowski reported a deadlock during system resume when virtio_net
driver is used.
The deadlock occurs because netif_device_attach() is called while holding
dev->tx_global_lock (via netif_tx_lock_bh() in virtnet_restore_up()).
netif_device_attach() calls __netdev_watchdog_up(), which now also tries
to acquire dev->tx_global_lock to synchronize with dev_watchdog().
This recursive lock acquisition results in a deadlock.
Fix this by removing the tx_global_lock acquisition from netdev_watchdog_up().
The critical state (watchdog_timer and watchdog_ref_held) is already
protected by dev->watchdog_lock, which was introduced in the blamed commit.
Fixes: 8eed5519e4 ("net: watchdog: fix refcount tracking races")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/netdev/a443376e-5187-4268-93b3-58047ef113a8@samsung.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260622110108.69541-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_master_redirect() dereferences the result of
netdev_master_upper_dev_get_rcu() without a NULL check, but that helper
returns NULL when the receiving device has no upper-master adjacency.
The reach guard only checks netif_is_bond_slave(). On bond slave release
bond_upper_dev_unlink() drops the upper-master adjacency before clearing
IFF_SLAVE, so an XDP_TX reaching xdp_master_redirect() in that window
still passes netif_is_bond_slave() while master is already NULL, and
faults on master->flags at offset 0xb0:
BUG: kernel NULL pointer dereference, address: 00000000000000b0
RIP: 0010:xdp_master_redirect (net/core/filter.c:4432)
Call Trace:
xdp_master_redirect (net/core/filter.c:4432)
bpf_prog_run_generic_xdp (include/net/xdp.h:700)
do_xdp_generic (net/core/dev.c:5608)
__netif_receive_skb_one_core (net/core/dev.c:6204)
process_backlog (net/core/dev.c:6319)
__napi_poll (net/core/dev.c:7729)
net_rx_action (net/core/dev.c:7792)
handle_softirqs (kernel/softirq.c:622)
__dev_queue_xmit (include/linux/bottom_half.h:33)
packet_sendmsg (net/packet/af_packet.c:3082)
__sys_sendto (net/socket.c:2252)
Kernel panic - not syncing: Fatal exception in interrupt
The missing check dates back to the original code; commit 1921f91298
("net, bpf: fix null-ptr-deref in xdp_master_redirect() for down master")
later added the master->flags read where the fault now lands but kept the
unconditional deref. Check master for NULL before use; a NULL master is
treated the same as one that is not up.
Fixes: 879af96ffd ("net, core: Add support for XDP redirection to slave device")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://patch.msgid.link/20260620201531.180123-1-xmei5@asu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tushar Vyavahare says:
====================
selftests/xsk: stabilize timeout test behavior
This series improves AF_XDP selftests by making timeout handling
explicit and fixing sources of non-determinism in xsk timeout tests.
Patch 1 introduces test_spec::poll_tmout and removes implicit
dependence on RX UMEM setup state for timeout behavior.
Patch 2 fixes thread harness sequencing by attaching XDP programs
before worker startup, removing signal-based termination, and using
barrier synchronization only for dual-thread runs.
Patch 3 restores shared_umem after POLL_TXQ_FULL so test-local
configuration does not leak into subsequent cases on shared-netdev
runs.
Together these changes make timeout handling easier to follow and
improve selftest stability, especially on real NIC runs.
====================
Link: https://patch.msgid.link/20260616154955.1492560-1-tushar.vyavahare@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
POLL_TXQ_FULL temporarily disables shared_umem on TX to exercise the
TX timeout path in isolation.
With shared_umem enabled, TX setup expects RX UMEM to be initialized
first and fails with: "RX UMEM is not initialized before shared-UMEM TX
setup".
Save and restore shared_umem around POLL_TXQ_FULL execution, and restore
it on both success and pkt_stream_replace() failure paths.
Also add an in-code comment explaining why shared_umem is temporarily
disabled in this test.
This keeps timeout setup local and prevents cross-test state leakage.
Signed-off-by: Tushar Vyavahare <tushar.vyavahare@intel.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20260616154955.1492560-4-tushar.vyavahare@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prevent workers from running before XDP program attachment completes.
The previous ordering allowed races between worker startup and setup.
Attach XDP programs before entering traffic validation.
Remove SIGUSR1-based worker termination and use pthread_join() for
thread shutdown so blocking syscalls are not interrupted.
Use barriers only for dual-thread runs so participants match and
teardown ordering stays deterministic.
This removes setup/startup races and stabilizes harness sequencing.
Signed-off-by: Tushar Vyavahare <tushar.vyavahare@intel.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20260616154955.1492560-3-tushar.vyavahare@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop inferring timeout behavior from RX UMEM initialization state.
That ties timeout semantics to setup internals and obscures intent.
Use test_spec::poll_tmout as the explicit timeout-mode selector in
TX and RX paths.
In RX, treat poll timeout as expected only in timeout mode.
In TX, let send_pkts() own loop completion in non-timeout mode
and use __send_pkts() only for progress and timeout detection.
This makes timeout logic explicit and keeps control flow predictable.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tushar Vyavahare <tushar.vyavahare@intel.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20260616154955.1492560-2-tushar.vyavahare@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The net-next-hw spinners on netdev.bots.linux.dev observe failing
so-txtime-py tests. A review of stdout shows most failures to be
due to exceeding the 4ms grace period. All I saw were within 8ms.
So increase to that.
Double the bounds from 4 to 8ms. This is still is small enough to
differentiate the delays programmed by the test, 10 and 20ms.
Fixes: 5c6baef388 ("selftests: drv-net: convert so_txtime to drv-net")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20260610170651.1b644001@kernel.org/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260621200137.1564776-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In airoha_qdma_set_chan_tx_sched(), the loop clearing queue mask was
using AIROHA_NUM_TX_RING (32) instead of AIROHA_NUM_QOS_QUEUES (8).
Each channel has 8 queues, and TXQ_DISABLE_CHAN_QUEUE_MASK(channel, i)
computes BIT(i + (channel * 8)). With i ranging 0..31, this causes:
- channel 0: clears bit 0..31 (all 4 channels) instead of 0..7
- channel 1: clears bit 8..31 (channels 1-3) instead of 8..15
- channel 2: clears bit 16..31 (channels 2-3) instead of 16..23
- channel 3: clears bit 24..31 (channel 3 only) - correct by accident
While BIT(32+) on arm64 produces 64-bit values truncated to 0 in u32
mask parameter, the loop still incorrectly clears queues within the
same channel beyond queue 7.
Even though this is functionally harmless (the register resets to 0
and is only ever cleared, never set — so clearing extra bits is a
no-op), the loop bound is semantically wrong and should be fixed for
correctness and clarity.
Fix by using AIROHA_NUM_QOS_QUEUES (8) as the loop upper bound.
Fixes: ef1ca92713 ("net: airoha: Add sched HTB offload support")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Wayen Yan <win847@gmail.com>
Link: https://patch.msgid.link/178187479434.2400840.1312143943526335838@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the allocation of fp[i].tpa_info fails, the error path will not free
the struct bnx2x_fastpath allocated earlier, as it is not linked to the
bp structure yet. Fix that by linking it immediately after allocation.
Cc: stable@vger.kernel.org
Fixes: 15192a8cf8 ("bnx2x: Split the FP structure")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260620062402.89549-1-nihaal@cse.iitm.ac.in
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_IP_MULTIPLE_TABLES is enabled but no rule is added,
fib_lookup() performs route lookup directly on two tables.
Since the first lookup does not properly bail out, the result
of an error route in the merged local/main table could be
overwritten by another route in the default table:
# unshare -n
# ip link set lo up
# ip route add 192.168.0.0/24 dev lo table 253
# ip route add unreachable 192.168.0.0/24
# ip route get 192.168.0.1
192.168.0.1 dev lo table default uid 0
cache <local>
Once a random rule is added, the error route is respected:
# ip rule add table 0
# ip rule del table 0
# ip route get 192.168.0.1
RTNETLINK answers: No route to host
Let's fix the inconsistent behaviour.
Fixes: f4530fa574 ("ipv4: Avoid overhead when no custom FIB rules are installed.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260619212753.3367244-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel selftests wait 1.25x of the promised stats refresh time
(as read from ethtool -c). bnxt reports 1sec by default, but
the stats update process has two steps. First device DMAs the
new values, then the service task performs update in full-width
SW counters. So the worst case delay is actually 2x.
Note that the behavior is different for ring stats and port stats.
Port stats are fetched synchronously by the service worker, so
there's no risk of doubling up the delay there.
The problem of stale stats impacts not only tests but real workloads
which monitor egress bandwidth of a NIC. The inaccuracy causes double
counting in the next cycle and spurious overload alarms.
Try to read from the DMA buffer more aggressively, to mitigate
timing issues between DMA and service task. The SW update should
be cheap.
Fixes: 51f307856b ("bnxt_en: Allow statistics DMA to be configurable using ethtool -C.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260619191538.104165-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fib6_nh_mtu_change() re-fetches idev via __in6_dev_get(arg->dev) and
dereferences idev->cnf.mtu6 without a NULL check. addrconf_ifdown()
clears dev->ip6_ptr with RCU_INIT_POINTER() after rt6_disable_ip() has
released tb6_lock, so the RA-driven MTU walk can observe a NULL idev and
oops. The caller rt6_mtu_change_route() guards its own __in6_dev_get(),
but this re-fetch is unguarded; nexthop-backed routes survive
addrconf_ifdown()'s flush, so the walk still reaches it after ip6_ptr is
nulled.
Return 0 when idev is NULL, matching rt6_mtu_change_route() and the
fib6_mtu() fix in commit 5ad509c1fd ("ipv6: Fix null-ptr-deref in
fib6_mtu().").
Oops: general protection fault, ... KASAN: null-ptr-deref in range
[0x00000000000002a8-0x00000000000002af]
RIP: 0010:fib6_nh_mtu_change+0x203/0x990
rt6_mtu_change_route+0x141/0x1d0
__fib6_clean_all+0xd0/0x160
rt6_mtu_change+0xb4/0x100
ndisc_router_discovery+0x24b5/0x2cb0
icmpv6_rcv+0x12e9/0x1710
ipv6_rcv+0x39b/0x410
Fixes: c0b220cf7d ("ipv6: Refactor exception functions")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Reviewed-by: Fernando Fernandez Mancera <fmancera@suse.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260619045334.2427073-1-xmei5@asu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each PPP control protocol (LCP/IPCP/IPV6CP) embedded in struct ppp
registers a timer via timer_setup(). That struct ppp is the
hdlc->state allocation, which detach_hdlc_protocol() frees with kfree()
in both teardown paths: unregister_hdlc_device() and the re-attach inside
attach_hdlc_protocol().
The ppp proto never registered a .detach callback, so
detach_hdlc_protocol() performs no timer synchronization before the
kfree(). The only cancel, timer_delete(&proto->timer) in ppp_cp_event(),
is partial (it does not wait for a running callback) and only runs on the
->CLOSED transition; ppp_stop()/ppp_close() do not sync either. A
ppp_timer callback already executing (blocked on ppp->lock) survives the
kfree and then dereferences proto->state / ppp->lock in freed memory,
leading to a use-after-free.
Fix this by adding a .detach helper that calls timer_shutdown_sync() on
every per-proto timer. detach_hdlc_protocol() invokes proto->detach(dev)
before kfree(hdlc->state), so timer_shutdown_sync()
now runs on both free paths.
timer_shutdown_sync() is used instead of timer_delete_sync() because the
keepalive path re-arms the timer through add_timer()/mod_timer() and
shutdown blocks any re-activation during teardown.
Initialize the per-protocol timers in ppp_ioctl() when the protocol is
attached, and remove the now-redundant timer_setup() from ppp_start(), so
that the timers are initialized exactly once at attach time and
ppp_timer_release() never operates on uninitialized timer_list
structures. attach_hdlc_protocol() uses kmalloc() (not kzalloc), so
struct ppp's protos[i].timer is uninitialized garbage until the first
timer_setup(); without this init-at-attach, attaching the PPP protocol
without ever bringing the device up would leave timer_shutdown_sync()
operating on uninitialized memory in .detach. Moving the init out of
ppp_start() (which only runs on NETDEV_UP) into the attach path makes the
initialization unconditional and avoids initializing the same timer_list
twice.
This bug was found by static analysis.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260617020518.116319-1-fanwu01@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
icssg_ndo_get_stats64() unconditionally calls emac_get_stat_by_name()
with FW PA stat names regardless of whether the PA stats block is
present on the hardware. emac_get_stat_by_name() already guards the
PA stats lookup with `if (emac->prueth->pa_stats)`; when that pointer
is NULL the lookup falls through to netdev_err() and returns -EINVAL.
Because ndo_get_stats64 is polled regularly by the networking stack
this produces thousands of log entries of the form:
icssg-prueth icssg1-eth end0: Invalid stats FW_RX_ERROR
A secondary consequence is that the int(-EINVAL) return value is
implicitly widened to a near-ULLONG_MAX unsigned value when accumulated
into the __u64 fields of rtnl_link_stats64, silently corrupting the
rx_errors, rx_dropped and tx_dropped counters reported by `ip -s link`.
Every other PA-aware code path in the driver is already guarded with
the same `if (emac->prueth->pa_stats)` check. Apply the same guard
here.
Fixes: 0d15a26b24 ("net: ti: icssg-prueth: Add ICSSG FW Stats")
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Cc: danishanwar@ti.com
Cc: rogerq@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260618093037.3448858-1-dev@pschenker.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ofdpa_port_fdb(), the hash_del() only unlinks the node from
hash table, but does not free it.
Fix this by adding kfree(found) after the !found == removing check,
where the pointer value is no longer needed.
Found by Coccinelle kfree script.
Cc: <stable+noautosel@kernel.org> # rocker is a test harness, it's never loaded on production systems
Signed-off-by: Ziran Zhang <zhangcoder@yeah.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260616013245.7098-1-zhangcoder@yeah.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=GGDL
-----END PGP SIGNATURE-----
Merge tag 'nf-26-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net. This batches
fixes for real crashes with trivial/correctness fixes. There is too
a rework of the conntrack expectation timeout strategy to deal with
a possible race when removing an expectation.
1) Fix the incorrect flowtable timeout extension for entries in
hw offload, from Adrian Bente. This is correcting a defect in
the functionality, no crash.
2) Hold reference to device under the fake dst in br_netfilter,
from Haoze Xie. This is fixing a possible UaF if the device
is removed while packet is sitting in nfqueue.
3) Reject template conntrack in xt_cluster, otherwise access to
uninitialize conntrack fields are possible leading to WARN_ON
due to unset layer 3 protocol. From Wyatt Feng.
4) Make sure the IPv6 tunnel header is in the linear skb data
area before pulling. While at it remove incomplete NEXTHDR_DEST
support. From Lorenzo Bianconi. This possibly leading to crash
if IPv4 header is not in the linear area.
5) Use test_bit_acquire in ipset hash set to avoid reordering
of subsequent memory access. This is addressing a LLM related
report, no crash has been observed. From Jozsef Kadlecsik.
6) Use test_bit_acquire in ipset bitmap set too, for the same
reason as in the previous patch, from Jozsef Kadlecsik.
7) Call kfree_rcu() after rcu_assign_pointer() to address a
possible UaF if kfree_rcu() runs inmediately, which to my
understanding never happens. Never observed in practise,
reported by LLM. Also from Jozsef Kadlecsik.
8) Use disable_delayed_work_sync() instead cancel_delayed_work_sync()
to avoid that ipset GC handler re-queues work as reported by LLM.
From Jozsef Kadlecsik. This is for correctness.
9) Restore the check in nft_payload for exceeding payloda offset
over 2^16. From Florian Westphal. This fixes a silent truncation,
not a big deal, but better be assertive and reject it.
10) Validate NFT_META_BRI_IIFHWADDR can only run from bridge
prerouting. From Florian Westphal. Harmless but it could allow
to read bytes from skb->cb.
11) Zero out destination hardware address during the flowtable
path setup, also from Florian. This is a correctness fix, LLM
points that possible infoleak can happen but topology to achieve
it is not clear.
12) Skip IPv4 options if present when building the IPV4 reject reply.
Otherwise bytes in the IPv4 options header can be sent back to
origin where the ICMP header is being expected. Again from
Florian Westphal.
13) Replace timer API for expectation by GC worker approach. This
is implicitly fixing a race between nf_ct_remove_expectations()
which might fail to remove the expectation due to timer_del()
returning false because timer has expired and callback is
being run concurrently. This fix is addressing a crash that has
been already reported with a reproducer.
14) Check if br_vlan_get_pvid_rcu() fails, otherwise possible stack
infoleak of 4-bytes. From Florian Westphal.
* tag 'nf-26-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_meta_bridge: fix NFT_META_BRI_IIFPVID stack leak
netfilter: nf_conntrack_expect: use conntrack GC to reap expectations
netfilter: nf_reject: skip iphdr options when looking for icmp header
netfilter: nft_flow_offload: zero device address for non-ether case
netfilter: nft_meta_bridge: add validate callback for get operations
netfilter: nft_payload: reject offsets exceeding 65535 bytes
netfilter: ipset: make sure gc is properly stopped
netfilter: ipset: fix order of kfree_rcu() and rcu_assign_pointer()
netfilter: ipset: Don't use test_bit() in lockless RCU readers in bitmap types
netfilter: ipset: Don't use test_bit() in lockless RCU readers in hash types
netfilter: flowtable: fix and simplify IP6IP6 tunnel handling
netfilter: xt_cluster: reject template conntracks in hash match
netfilter: nf_queue: pin bridge device while NFQUEUE holds fake dst
netfilter: flowtable: fix offloaded ct timeout never being extended
====================
Link: https://patch.msgid.link/20260620222738.112506-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dpaa2-switch driver does not support VLAN uppers while its ports are
bridged. This scenario tried to be prevented by rejecting a bridge join
while VLAN uppers exist but the reverse order was still possible.
This patches adds a check so that the dpaa2-switch also does not accept
VLAN uppers while bridged.
Fixes: f48298d3fb ("staging: dpaa2-switch: move the driver out of staging")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260618092813.432535-2-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IOAM uses a dummy dst_entry(null_dst) to mark that the destination should
not be changed after the transformation. This dst is stored in the IOAM lwt
state and may be passed to dst_cache_set_ip6().
However, the IPv6 dst cache path eventually calls rt6_get_cookie(), which
treats the dst_entry as part of a struct rt6_info. Since the null_dst was
embedded directly as a struct dst_entry in struct ioam6_lwt, this resulted
in an invalid cast and rt6_get_cookie() reading fields from the wrong
object.
In practice, the wrong cookie is not used while dst->obsolete is zero, but
rt6_get_cookie() may also access per-cpu value when rt->sernum is
zero. In this case, rt->sernum aliases ioam6_lwt::cache::reset_ts, which
can become zero, making this a potential invalid pointer access.
Fix this by embedding a full struct rt6_info for the dummy IPv6 route and
passing its dst member to the dst APIs.
Fixes: 47ce7c8545 ("net: ipv6: ioam6: fix double reallocation")
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Reviewed-by: Justin Iurman <justin.iurman@gmail.com>
Link: https://patch.msgid.link/20260618104336.48934-1-jiayuan.chen@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In __ip6_append_data(), when the paged-allocation branch is taken
(MSG_MORE / NETIF_F_SG / large fraglen), alloclen and pagedlen are
computed as
alloclen = fragheaderlen + transhdrlen;
pagedlen = datalen - transhdrlen;
datalen already includes fraggap (datalen = length + fraggap). When
fraggap is non-zero, this is not the first skb and transhdrlen is zero.
The fraggap bytes carried over from the previous skb are copied just past
the fragment headers in the new skb's linear area. The linear area is
therefore undersized by fraggap bytes while pagedlen is overstated by the
same amount, and the copy writes past skb->end into the trailing
skb_shared_info.
An unprivileged user can trigger this via a UDPv6 socket using
MSG_MORE together with MSG_SPLICE_PAGES.
The bad accounting was introduced by commit 773ba4fe91 ("ipv6:
avoid partial copy for zc"). Before commit ce650a1663 ("udp6: Fix
__ip6_append_data()'s handling of MSG_SPLICE_PAGES"), the negative
copy value caused -EINVAL to be returned. That later commit allowed
MSG_SPLICE_PAGES to proceed in this case, making the corruption
triggerable.
The non-paged branch sets alloclen to fraglen, which already accounts
for fraggap because datalen does. Bring the paged branch in line by
adding fraggap to alloclen and subtracting it from pagedlen.
After this adjustment, copy no longer collapses to -fraggap on the
paged path, so remove the stale comment describing that old arithmetic.
Since a negative copy is no longer expected for a valid MSG_SPLICE_PAGES
case, remove the MSG_SPLICE_PAGES exception from the negative copy check.
Fixes: 773ba4fe91 ("ipv6: avoid partial copy for zc")
Signed-off-by: Jungwoo Lee <jwlee2217@gmail.com>
Signed-off-by: Wongi Lee <qw3rtyp0@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/ajFTqRljatR17fFy@DESKTOP-19IMU7U.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In __ip_append_data(), when the paged-allocation branch is taken,
alloclen and pagedlen are computed as
alloclen = fragheaderlen + transhdrlen;
pagedlen = datalen - transhdrlen;
datalen already includes fraggap, but the fraggap bytes carried over
from the previous skb are copied into the new skb's linear area at
offset transhdrlen by the subsequent skb_copy_and_csum_bits(). The
linear area is therefore undersized by fraggap bytes while pagedlen is
overstated by the same amount.
The non-paged branch sets alloclen to fraglen, which already accounts
for fraggap because datalen does. Bring the paged branch in line by
adding fraggap to alloclen and subtracting it from pagedlen.
After this adjustment, copy no longer collapses to -fraggap on the
paged path, so remove the stale comment describing that old arithmetic.
Fixes: 8eb77cc739 ("ipv4: avoid partial copy for zc")
Signed-off-by: Jungwoo Lee <jwlee2217@gmail.com>
Signed-off-by: Wongi Lee <qw3rtyp0@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/ajFR1eLAIs42TN3g@DESKTOP-19IMU7U.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a regression test for DualPI2 GSO backlog accounting when it is
used as a child qdisc of QFQ.
The test sends one UDP GSO datagram through a QFQ class with DualPI2 as
the leaf qdisc. DualPI2 splits the skb into two segments. After the
traffic drains, both QFQ and DualPI2 must report zero backlog and zero
qlen.
On kernels with the broken accounting, QFQ can keep a stale non-zero
qlen after all real packets have been dequeued.
Signed-off-by: Xingquan Liu <b1n@b1n.io>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20260619151447.223640-2-b1n@b1n.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When DualPI2 splits a GSO skb into N segments, it propagates N
additional packets to its parent before returning NET_XMIT_SUCCESS.
The parent then accounts for the original skb once more, leaving its
qlen one larger than the number of packets actually queued.
With QFQ as the parent, after all real packets are dequeued, QFQ still
has a non-zero qlen while its in-service aggregate has no active
classes. qfq_choose_next_agg() returns NULL and qfq_dequeue() passes
the result to qfq_peek_skb(), causing a NULL pointer dereference.
Follow the same pattern used by tbf_segment() and taprio: count only
successfully queued segments, propagate the difference between the
original skb and those segments, and return NET_XMIT_SUCCESS whenever
at least one segment was queued.
Fixes: 8f9516daed ("sched: Add enqueue/dequeue of dualpi2 qdisc")
Cc: stable@vger.kernel.org
Signed-off-by: Xingquan Liu <b1n@b1n.io>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20260619151447.223640-1-b1n@b1n.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
accept_untracked_na() re-fetches the inet6_dev with __in6_dev_get(dev)
and dereferences idev->cnf.accept_untracked_na without a NULL check,
even though its only caller ndisc_recv_na() already fetched and
NULL-checked idev for the same device.
Both reads of dev->ip6_ptr run in the same RCU read-side critical
section, but a concurrent addrconf_ifdown() can clear dev->ip6_ptr
between them: lowering the MTU below IPV6_MIN_MTU calls addrconf_ifdown()
without the synchronize_net() that orders the unregister path, so the
re-fetch returns NULL and oopses:
BUG: KASAN: null-ptr-deref in ndisc_recv_na (net/ipv6/ndisc.c:974)
Read of size 4 at addr 0000000000000364
Call Trace:
<IRQ>
ndisc_recv_na (net/ipv6/ndisc.c:974)
icmpv6_rcv (net/ipv6/icmp.c:1193)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:479)
ip6_input_finish (net/ipv6/ip6_input.c:534)
ip6_input (net/ipv6/ip6_input.c:545)
ip6_mc_input (net/ipv6/ip6_input.c:635)
ipv6_rcv (net/ipv6/ip6_input.c:351)
</IRQ>
It is reachable by an unprivileged user via a network namespace.
Pass the caller's already validated idev instead of re-fetching it; the
idev stays alive for the whole RCU critical section, so it is safe even
after dev->ip6_ptr has been cleared.
Fixes: aaa5f515b1 ("net: ipv6: new accept_untracked_na option to accept na only if in-network")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://patch.msgid.link/20260617065512.2529757-2-bestswngs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipip6_changelink() operates on at most two netns, dev_net(dev) and the
tunnel link netns t->net. They differ once the device is created in or
moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in t->net can rewrite a tunnel that
lives in t->net.
Gate ipip6_changelink() on rtnl_dev_link_net_capable() at its top,
before any attribute is parsed. sit was the one tunnel type not covered
by the recent series that added this check to the other changelink()
handlers.
Fixes: 5e6700b3bf ("sit: add support of x-netns")
Link: https://lore.kernel.org/netdev/20260612085941.3158249-1-maoyixie.tju@gmail.com/
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260618070817.3378283-1-maoyixie.tju@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In airoha_dev_select_queue(), the expression:
queue = (skb->priority - 1) % AIROHA_NUM_QOS_QUEUES;
implicitly converts to unsigned arithmetic: when skb->priority is 0
(the default for unclassified traffic), (0u - 1u) wraps to UINT_MAX,
and UINT_MAX % 8 = 7, routing default best-effort packets to the
highest-priority QoS queue. This causes QoS inversion where the
majority of traffic on a PON gateway starves actual high-priority
flows (VoIP, gaming, etc.).
The "- 1" offset was a leftover from the ETS offload implementation
that has since been removed. The correct mapping is a direct modulo:
queue = skb->priority % AIROHA_NUM_QOS_QUEUES;
This maps priority 0 → queue 0 (lowest), priority 7 → queue 7
(highest), with higher priorities wrapping around. This is the
standard Linux sk_prio → HW queue mapping used by other drivers.
Fixes: 2b288b8156 ("net: airoha: Introduce ndo_select_queue callback")
Link: https://lore.kernel.org/netdev/178185573207.2378135.3729126358670287878@gmail.com/
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Joe Damato <joe@dama.to>
Signed-off-by: Wayen Yan <win847@gmail.com>
Link: https://patch.msgid.link/178194366700.2485734.5368768965976693502@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcf_ct_fill_params() calls nf_connlabels_get() (setting put_labels) when
TCA_CT_LABELS is present, but two later error sites use a bare return
instead of "goto err", skipping the err: nf_connlabels_put() cleanup.
They also precede the "p->put_labels = put_labels" assignment, so the
tcf_ct_params_free() fallback does not release the count either. Each
failed RTM_NEWACTION on these paths leaks one nf_connlabels reference:
net->ct.labels_used is incremented and never released. The action is
reachable with CAP_NET_ADMIN over the netns, i.e. from an unprivileged
user namespace on default-userns kernels.
Impact: an unprivileged user with CAP_NET_ADMIN over a network namespace
(e.g. via user namespaces) leaks one nf_connlabels reference per failed
RTM_NEWACTION on the two error paths; net->ct.labels_used is never
released.
The err: label is safe to reach from both sites: p->tmpl is still NULL
there (kzalloc'd, not yet assigned) and nf_ct_put(NULL) is a no-op, so
no inline release is needed.
Fixes: 70f06c115b ("sched: act_ct: switch to per-action label counting")
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260617215708.1115818-1-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
