The cs89x0 driver is really two in one, and they are mutually exclusive:
- the ISA driver was used on 486-era PCs. It likely has no remaining
users, like the other ethernet drivers that got removed in
linux-7.1. The DMA support in here is the last device driver use of
the deprecated isa_bus_to_virt() interface, all other users are either
x86 specific or or got converted to the normal dma-mapping interface.
The driver was maintained by Andrew Morton at the time, based on
the linux-2.2 vendor driver from Cirrus Logic.
- the platform_driver instance was used on some embedded Arm boards
around the same time, such as the EP7211 Development Kit. This
is the same chip, but uses modern devicetree based probing and no DMA.
This was added by Alexander Shiyan.
Remove the ISA driver as a cleanup, including all of the outdated
documentation referring to its configuration.
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260429145624.2948432-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We try to validate during registration that the netdev
has ops if it has features. This is currently somewhat sillily
written because we have a dereference before a NULL check
on the ops struct. Straighten this out.
No functional change intended other than saving ourselves
the very theoretical crash with a bad driver.
Note that we check earlier in the function that either ops
or TLS features are set for the device in question.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260429213001.1908235-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
net/sched: tc_dump_qdisc() optimizations
Before converting tc_dump_qdisc() to RCU, we make the following changes:
- Use for_each_netdev_dump() instead of for_each_netdev()
- Only dump qdiscs of a single device at user space request.
====================
Link: https://patch.msgid.link/20260430023628.3216283-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no point dumping qdiscs for all devices when user space
wants them for a single device:
tc -s -d qdisc show dev eth1
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260430023628.3216283-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use for_each_netdev_dump() instead of for_each_netdev().
This is more scalable, and will ease RCU conversion.
This also offer better behavior when other threads
are adding or deleting netevices concurrently.
This enables dumping qdiscs for a single device
at user space request in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260430023628.3216283-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change tc_fill_qdisc() to return -EMSGSIZE when skb is too small.
Change tc_dump_qdisc_root() to propagate tc_fill_qdisc() error to its callers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260430023628.3216283-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change tc_fill_tclass() to return -EMSGSIZE when skb is too small.
Change its caller to propagate this error (instead of -EINVAL)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260430023628.3216283-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These tests check syncookie mode is able to reconstruct some
client options when TCP TS are used:
- wscale option.
- sackOK.
- MSS (in a limited way, especially for IPv4).
- ECN : not enabled.
Note that IPv4 and IPv6 have different msstab[] values:
IPv4 msstab[4] = { 536, 1300, 1440, 1460 }
IPv6 msstab[4] = { 1280 - 60, 1480 - 60, 1500 - 60, 9000 - 60 }
IPv4 is currently capping SND_MSS to 1460, even on a 9K MTU network.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Link: https://patch.msgid.link/20260430021444.2929534-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan says:
====================
mlx5-next updates 2026-04-29
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Extend query_esw_functions output for multi-function support
net/mlx5: Remove unused host_sf_enable field
net/mlx5: Add function_id_type for enable/disable_hca cmds
mlx5: Rename the vport number enums for host PF and VF
====================
Link: https://patch.msgid.link/20260429212747.224411-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson says:
====================
bridge: Do not suppress ARP probes and DAD NS unconditionally
When using bridge neighbor suppression in EVPN deployments, Duplicate
Address Detection (DAD) is currently broken for both IPv4 (ARP probes)
and IPv6 (DAD Neighbor Solicitations). This prevents proper address
conflict detection across the VXLAN fabric.
The neighbor suppression feature allows the bridge to reply to ARP/NS
messages on behalf of remote hosts when FDB and neighbor entries exist,
suppressing unnecessary flooding over the VXLAN overlay. However, the
current implementation unconditionally suppresses ARP probes and DAD NS,
which breaks DAD.
For DAD to work correctly:
- When the bridge doesn't know the answer:
flood the probe/DAD packet to allow remote VTEPs to respond.
- When the bridge knows the answer:
reply to indicate the address is in use.
This series fixes the issue by adjusting the early suppression checks to
exclude ARP probes and DAD NS from unconditional suppression, allowing
them to reach the normal FDB lookup path. Gratuitous ARP and IPv6
unsolicited-NA messages are still suppressed unconditionally as before.
Patchset overview:
Patch #1: Fixes the unconditional suppression.
Patch #2: Adds selftests.
====================
Link: https://patch.msgid.link/20260429062405.1386417-1-danieller@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add test cases to verify that ARP probes and DAD Neighbor Solicitations
are handled correctly by the bridge neighbor suppression feature.
When neighbor suppression is enabled on a bridge VXLAN port, the bridge
should reply to ARP/NS messages on behalf of remote hosts when both FDB
and neighbor entries exist, and the answer is known. However, when
either the FDB or the neighbor exists, ARP probes / DAD NS should be
treated like regular ARP requests / NS and flood to VXLAN.
Add two new test functions:
neigh_suppress_arp_probe(): Tests ARP probe handling by triggering
duplicate address detection using arping -D. Verifies that probes are
flooded when the bridge doesn't know the answer, and suppressed when FDB
and neighbor entries exist.
neigh_suppress_dad_ns(): Tests DAD NS handling by constructing DAD NS
packets using mausezahn and verifies correct flooding/suppression
behavior.
Before the previous patch:
$ ./test_bridge_neigh_suppress.sh -t "neigh_suppress_arp_probe neigh_suppress_dad_ns"
Per-port ARP probe suppression
------------------------------
TEST: ARP probe suppression [ OK ]
TEST: "neigh_suppress" is on [ OK ]
TEST: ARP probe suppression [FAIL]
TEST: FDB and neighbor entry installation [ OK ]
TEST: arping [FAIL]
TEST: ARP probe suppression [FAIL]
TEST: neighbor removal [ OK ]
TEST: ARP probe suppression [FAIL]
TEST: "neigh_suppress" is off [ OK ]
TEST: ARP probe suppression [FAIL]
Per-port DAD NS suppression
---------------------------
TEST: DAD NS suppression [ OK ]
TEST: "neigh_suppress" is on [ OK ]
TEST: DAD NS suppression [FAIL]
TEST: FDB and neighbor entry installation [ OK ]
TEST: DAD NS suppression [FAIL]
TEST: neighbor removal [ OK ]
TEST: DAD NS suppression [FAIL]
TEST: DAD NS proxy NA reply [FAIL]
TEST: "neigh_suppress" is off [ OK ]
TEST: DAD NS suppression [FAIL]
Tests passed: 10
Tests failed: 10
After the previous patch:
$ ./test_bridge_neigh_suppress.sh -t "neigh_suppress_arp_probe neigh_suppress_dad_ns"
Per-port ARP probe suppression
------------------------------
TEST: ARP probe suppression [ OK ]
TEST: "neigh_suppress" is on [ OK ]
TEST: ARP probe suppression [ OK ]
TEST: FDB and neighbor entry installation [ OK ]
TEST: arping [ OK ]
TEST: ARP probe suppression [ OK ]
TEST: neighbor removal [ OK ]
TEST: ARP probe suppression [ OK ]
TEST: "neigh_suppress" is off [ OK ]
TEST: ARP probe suppression [ OK ]
Per-port DAD NS suppression
---------------------------
TEST: DAD NS suppression [ OK ]
TEST: "neigh_suppress" is on [ OK ]
TEST: DAD NS suppression [ OK ]
TEST: FDB and neighbor entry installation [ OK ]
TEST: DAD NS suppression [ OK ]
TEST: neighbor removal [ OK ]
TEST: DAD NS suppression [ OK ]
TEST: DAD NS proxy NA reply [ OK ]
TEST: "neigh_suppress" is off [ OK ]
TEST: DAD NS suppression [ OK ]
Tests passed: 20
Tests failed: 0
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260429062405.1386417-3-danieller@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When neighbor suppression is enabled on a VXLAN port, the bridge is
expected to reply to ARP/NS messages on behalf of remote hosts when both
FDB and neighbor entries exist. This allows the bridge to suppress
flooding of these messages to the VXLAN overlay.
According to RFC 9161 ("Operational Aspects of Proxy ARP/ND in Ethernet
Virtual Private Networks"):
"A PE SHOULD reply to broadcast/multicast address resolution messages,
i.e., ARP Requests, ARP probes, NS messages, as well as DAD NS messages.
An ARP probe is an ARP Request constructed with an all-zero sender IP
address that may be used by hosts for IPv4 Address Conflict Detection as
specified in [RFC5227]".
However, the current implementation unconditionally suppresses ARP probes
and DAD Neighbor Solicitations, which breaks Duplicate Address Detection
(DAD) over EVPN.
For DAD to work correctly over the VXLAN fabric:
- When the bridge does not know the answer:
flood the probe/DAD packet to allow remote VTEPs to respond.
- When the bridge knows the answer:
reply to indicate the address is in use.
Fix by adjusting the early suppression checks to exclude ARP probes and
DAD NS from unconditional suppression.
When replying to a DAD NS, br_nd_send() is adjusted to set the NA
destination to the all-nodes multicast address (ff02::1) and clear the
Solicited flag, in accordance with RFC 4861 section 7.2.4.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260429062405.1386417-2-danieller@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The alloc_pages() cannot satisfy requests exceeding MAX_PAGE_ORDER,
and attempting such allocations will lead to guaranteed failures
and potential kernel warnings.
For SMCR_PHYS_CONT_BUFS, cap the allocation order to MAX_PAGE_ORDER.
This ensures the attempts to allocate the largest possible physically
contiguous chunk succeed, instead of failing with an invalid order.
This also avoids redundant "try-fail-degrade" cycles in
__smc_buf_create().
For SMCR_MIXED_BUFS, no cap is needed: if the order exceeds
MAX_PAGE_ORDER, alloc_pages() will silently fail (__GFP_NOWARN)
and automatically fall back to virtual memory.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sidraya Jayagond <sidraya@linux.ibm.com>
Link: https://patch.msgid.link/20260429021637.21815-1-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- mac80211: major rework of station bandwidth handling,
fixing issues with lower capability than AP
- general: cleanups for EMLSR spec issues (drafts differed)
- ath9k: GPIO interface improvements
- ath12k: replace dynamic memory allocation in WMI RX path
-----BEGIN PGP SIGNATURE-----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=cEhV
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-04-30' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Some new content already, notably:
- mac80211: major rework of station bandwidth handling,
fixing issues with lower capability than AP
- general: cleanups for EMLSR spec issues (drafts differed)
- ath9k: GPIO interface improvements
- ath12k: replace dynamic memory allocation in WMI RX path
* tag 'wireless-next-2026-04-30' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (39 commits)
wifi: brcmsmac: phy_lcn: Remove dead code in wlc_lcnphy_radio_2064_channel_tune_4313()
wifi: mac80211: always allow transmitting null-data on TXQs
wifi: mac80211: use kstrtobool_from_user() in debugfs callbacks
wifi: cfg80211: validate cipher suite for NAN Data keys
wifi: nl80211: check link is beaconing for color change
wifi: mac80211: clarify an 802.11 VHT spec reference
wifi: mac80211: fix per-station PHY capability bandwidth
wifi: mac80211: clarify per-STA bandwidth handling
wifi: nl80211: always validate AP operation/PHY regulatory
wifi: cfg80211: provide HT/VHT operation for AP beacon
wifi: nl80211: reject too short HT/VHT/HE/EHT capability/operation
wifi: cfg80211: move AP HT/VHT/... operation to beacon info
wifi: nl80211: reject beacons with bad HE operation
wifi: cfg80211: remove HE/SAE H2E required fields
wifi: mac80211: remove ieee80211_sta_cur_vht_bw()
wifi: mac80211: clean up ieee80211_sta_cap_rx_bw()
wifi: mac80211: clean up initial STA NSS/bandwidth handling
wifi: mac80211: clean up STA NSS handling
wifi: mac80211: simplify ieee80211_sta_rx_bw_to_chan_width()
wifi: nl80211: document channel opmode change channel width
...
====================
Link: https://patch.msgid.link/20260430120304.249081-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're currently dumping skb info in our fragment input test, which makes
interpreting the TAP test output a bit awkward.
Remove the skb dumps.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260429-dev-mctp-test-skb-dump-v1-1-13fd5789ef71@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Fix a reference leak on device_register() failure in pata_parport
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRN+ES/c4tHlMch3DzJZDGjmcZNcgUCafNROAAKCRDJZDGjmcZN
cnFfAQD+x6vRvu0bpGab9J7gvZYYtbbsj12pCbVA9jPpS2AMXQEA/ity23nuogu4
vF+H+XKqSjfdRGhn5GZ9GMhIq4tNOQ4=
=0MCi
-----END PGP SIGNATURE-----
Merge tag 'ata-7.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fix from Niklas Cassel:
- Fix a reference leak on device_register() failure in pata_parport
* tag 'ata-7.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: pata_parport: switch to dynamic root device
A bunch of small fixes. One minor fix is found in the core side for
data race in PCM OSS layer, while remaining changes are various
device-specific fixes and quirks.
- Core: PCM OSS data race fix
- HD-audio: Fixes for TAS2781, CS35L56, and Realtek/Conexant quirks;
avoidance of a WARN_ON for HDMI channel mapping
- USB-audio: Improvements in UAC3 parsing robustness (leaks, size
checks) and fixes for potential endless loops
- ASoC: Driver-specific fixes for CS35L56, Intel bytcr_wm5102,
Spacemit, AW88395, and others, plus a new quirk for Steam Deck OLED.
- Misc: A UAF fix in aloop driver, division by zero fix in ua101
driver and leak fixes in caiaq driver
-----BEGIN PGP SIGNATURE-----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=SGI0
-----END PGP SIGNATURE-----
Merge tag 'sound-7.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bunch of small fixes. One minor fix is found in the core side for
data race in PCM OSS layer, while remaining changes are various
device-specific fixes and quirks.
- Core: PCM OSS data race fix
- HD-audio: Fixes for TAS2781, CS35L56, and Realtek/Conexant quirks;
avoidance of a WARN_ON for HDMI channel mapping
- USB-audio: Improvements in UAC3 parsing robustness (leaks, size
checks) and fixes for potential endless loops
- ASoC: Driver-specific fixes for CS35L56, Intel bytcr_wm5102,
Spacemit, AW88395, and others, plus a new quirk for Steam Deck
OLED
- Misc: A UAF fix in aloop driver, division by zero fix in ua101
driver and leak fixes in caiaq driver"
* tag 'sound-7.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (32 commits)
ALSA: hda/tas2781: Fix incorrect bit update for non-book-zero or book 0 pages >1
ALSA: hda: cs35l56: Fix uninitialized value in cs35l56_hda_read_acpi()
ALSA: hda/conexant: Fix missing error check for jack detection
ALSA: hda: Avoid WARN_ON() for HDMI chmap slot checks
ALSA: usb-audio: Fix quirk entry placement for PreSonus AudioBox USB
ASoC: spacemit: adjust FIFO trigger threshold to half FIFO size
ASoC: spacemit: move hw constraints from hw_params to startup
ASoC: codecs: ab8500: Fix casting of private data
ASoC: cs35l56: Fix illegal writes to OTP_MEM registers
ASoC: Intel: bytcr_wm5102: Fix MCLK leak on platform_clock_control error
ALSA: usb-audio: Avoid potential endless loop in convert_chmap_v3()
ALSA: usb-audio: Fix potential leak of pd at parsing UAC3 streams
ALSA: caiaq: Don't abort when no input device is available
ALSA: caiaq: Fix potentially leftover ep1_in_urb at error path
ASoC: aw88395: Fix kernel panic caused by invalid GPIO error pointer
ALSA: caiaq: fix usb_dev refcount leak on probe failure
sound: ua101: fix division by zero at probe
ALSA: usb-audio: apply quirk for Playstation PDP Riffmaster
ALSA: hda: Remove duplicate cmedia entries in codecs Makefile
ALSA: hda/realtek: Add micmute LED quirk for Acer Aspire A315-44P
...
Ivan Vecera says:
====================
dpll: add pin operational state
Add pin operational state (operstate) to the DPLL subsystem to
separate administrative intent from actual hardware status.
Currently pin-state mixes what the user requested (connected,
selectable, disconnected) with what the hardware is actually doing.
This makes it difficult to diagnose situations where a user sets
a pin as selectable or connected but the hardware cannot use it
due to signal issues.
The new operstate attribute is reported inside the pin-parent-device
nest alongside the existing state and is read-only. Defined values:
- active: pin is qualified and actively used by the DPLL
- standby: pin is qualified but not actively used by the DPLL
- no-signal: pin does not have a valid signal
- qual-failed: pin signal failed qualification checks
Patch 1 adds the operstate enum, netlink attribute and the
operstate_on_dpll_get callback to the DPLL subsystem. It also
updates Documentation/driver-api/dpll.rst to describe the
separation between admin state and operational state.
Patch 2 implements the callback for ZL3073x input pins using the
reference monitor status register. It also refactors the existing
state_on_dpll_get to return purely administrative state and switches
periodic monitoring to track operstate changes.
====================
Link: https://patch.msgid.link/20260428154907.2820654-1-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Implement operstate_on_dpll_get callback for input pins to report
the actual hardware status:
- active: pin is the currently locked reference
- standby: signal is valid but pin is not actively used
- no-signal: reference monitor reports Loss of Signal (LOS)
- qual-failed: reference monitor reports a qualification failure
(SCM, CFM, GST, PFM, eSync or Split-XO)
Separate administrative state (state_on_dpll_get) from operational
state: admin state now reports purely the user-requested intent
(connected in reflock mode, selectable in auto mode).
Switch periodic monitoring to track operstate changes instead of
the mixed admin/oper state that was previously reported.
Add ref_mon_status bit definitions to regs.h.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Petr Oros <poros@redhat.com>
Link: https://patch.msgid.link/20260428154907.2820654-3-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add pin-operstate enum and operstate_on_dpll_get callback to report
the actual hardware status of a pin with respect to its parent DPLL
device. Unlike pin-state (which reflects administrative intent set
by the user), operstate reflects what the hardware is actually doing.
Defined operational states:
- active: pin is qualified and actively used by the DPLL
- standby: pin is qualified but not actively used by the DPLL
- no-signal: pin does not have a valid signal
- qual-failed: pin signal failed qualification
The operstate is reported inside the pin-parent-device nested
attribute alongside the existing state and phase-offset attributes.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Petr Oros <poros@redhat.com>
Link: https://patch.msgid.link/20260428154907.2820654-2-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Return -EIO if efx_mcdi_rpc() doesn't return enough space.
Fixes: 14743ddd24 ("sfc: add devlink info support for ef100")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/afGpsbLRHL4_H0KS@stanley.mountain
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When tls_set_device_offload_rx() fails at tls_dev_add(), the error path
calls tls_sw_free_resources_rx() to clean up the SW context that was
initialized by tls_set_sw_offload(). This function calls
tls_sw_release_resources_rx() (which stops the strparser via
tls_strp_stop()) and tls_sw_free_ctx_rx() (which kfrees the context),
but never frees the anchor skb that was allocated by alloc_skb(0) in
tls_strp_init().
Note that tls_sw_free_resources_rx() is exclusively used for this
"failed to start offload" code path, there's no other caller.
The leak did not exist before commit 84c61fe1a7 ("tls: rx: do not use
the standard strparser"), because the standard strparser doesn't try
to pre-allocate an skb.
The normal close path in tls_sk_proto_close() handles cleanup by calling
tls_sw_strparser_done() (which calls tls_strp_done()) after dropping
the socket lock, because tls_strp_done() does cancel_work_sync() and
the strparser work handler takes the socket lock.
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260428231559.1358502-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jacob Keller says:
====================
Intel Wired LAN Update 2026-04-27 (ice, iavf)
Petr Oros from RedHat has accumulated a number of fixes for the Intel ice
and iavf drivers, bundled together in this series.
First, a series of 4 fixes to resolve issues with the iavf driver logic for
handling VLAN filters. This includes keeping VLAN filters while the
interface is brought down, waiting for confirmation on filter deletion
before deleting filters from the driver tracking structures, and handling
the VIRTCHNL_OP_ADD_VLAN for the old v1 VLAN_ADD command.
A fix for a crash in ice_reset_all_vfs(), properly checking for errors when
ice_vf_rebuild_vsi() fails.
A fix for a possible infinite recursion in ice_cfg_tx_topo() that occurs
when trying to apply invalid Tx topology configuration.
A fix to initialize the SMA pins in the DPLL subsystem properly.
A fix to change the SMA and U.FL pin state for paired pins, ensuring that
all flows changing one pin will also update its shared pin appropriately.
A preparatory patch to export __dpll_pin_change_ntf() so that drivers can
notify pin changes while already holding the dpll_lock.
A fix to ensure DPLL notifications are sent for the software-controlled
pins which wrap the physical CGU input/output pins.
A fix to add DPLL notifications for peer pins when changing the SMA or U.FL
pins, ensuring DPLL subsystem is notified about the paired connected pins.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
====================
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-0-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
SMA and U.FL pins share physical signal paths in pairs (SMA1/U.FL1 and
SMA2/U.FL2). When one pin's state changes via a PCA9575 GPIO write,
the paired pin's state also changes, but no notification is sent for
the peer pin. Userspace consumers monitoring the peer via dpll netlink
subscribe never learn about the update.
Add ice_dpll_sw_pin_notify_peer() which sends a change notification for
the paired SW pin. Call it from ice_dpll_pin_sma_direction_set(),
ice_dpll_sma_pin_state_set(), and ice_dpll_ufl_pin_state_set() after
pf->dplls.lock is released. Use __dpll_pin_change_ntf() because
dpll_lock is still held by the dpll netlink layer (dpll_pin_pre_doit).
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-11-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The SMA/U.FL pin redesign (commit 2dd5d03c77 ("ice: redesign dpll
sma/u.fl pins control")) introduced software-controlled pins that wrap
backing CGU input/output pins, but never updated the notification and
data paths to propagate pin events to these SW wrappers.
The periodic work sends dpll_pin_change_ntf() only for direct CGU input
pins. SW pins that wrap these inputs never receive change or phase
offset notifications, so userspace consumers such as synce4l monitoring
SMA pins via dpll netlink never learn about state transitions or phase
offset updates. Similarly, ice_dpll_phase_offset_get() reads the SW
pin's own phase_offset field which is never updated; the PPS monitor
writes to the backing CGU input's field instead.
Fix by introducing ice_dpll_pin_ntf(), a wrapper around
dpll_pin_change_ntf() that also notifies any registered SMA/U.FL pin
whose backing CGU input matches. Replace all direct
dpll_pin_change_ntf() calls in the periodic notification paths with
this wrapper. Fix ice_dpll_phase_offset_get() to return the backing
CGU input's phase_offset for input-direction SW pins.
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-10-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Export __dpll_pin_change_ntf() so that drivers can send pin change
notifications from within pin callbacks, which are already called
under dpll_lock. Using dpll_pin_change_ntf() in that context would
deadlock.
Add lockdep_assert_held() to catch misuse without the lock held.
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-9-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
SMA and U.FL pins share physical signal paths in pairs (SMA1/U.FL1 and
SMA2/U.FL2) controlled by the PCA9575 GPIO expander. Each pair can
only have one active pin at a time: SMA1 output and U.FL1 output share
the same CGU output, SMA2 input and U.FL2 input share the same CGU
input. The PCA9575 register bits determine which connector in each
pair owns the signal path.
The driver does not account for this pairing in two places:
ice_dpll_ufl_pin_state_set() modifies PCA9575 bits and disables the
backing CGU pin without checking whether the U.FL pin is currently
active. Disconnecting an already inactive U.FL pin flips bits that
the paired SMA pin relies on, breaking its connection.
ice_dpll_sma_direction_set() does not propagate direction changes to
the paired U.FL pin. For SMA2/U.FL2 the ICE_SMA2_UFL2_RX_DIS bit is
never managed, so U.FL2 stays disconnected after SMA2 switches to
output. For both pairs the backing CGU pin of the U.FL side is never
enabled when a direction change activates it, so userspace sees the
pin as disconnected even though the routing is correct.
Fix by guarding the U.FL disconnect path against inactive pins and by
updating the paired U.FL pin fully on SMA direction changes: manage
ICE_SMA2_UFL2_RX_DIS for the SMA2/U.FL2 pair and enable the backing
CGU pin whenever the peer becomes active.
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-8-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DPLL SMA/U.FL pin redesign introduced ice_dpll_sw_pin_frequency_get()
which gates frequency reporting on the pin's active flag. This flag is
determined by ice_dpll_sw_pins_update() from the PCA9575 GPIO expander
state. Before the redesign, SMA pins were exposed as direct HW
input/output pins and ice_dpll_frequency_get() returned the CGU
frequency unconditionally — the PCA9575 state was never consulted.
The PCA9575 powers on with all outputs high, setting ICE_SMA1_DIR_EN,
ICE_SMA1_TX_EN, ICE_SMA2_DIR_EN and ICE_SMA2_TX_EN. Nothing in the
driver writes the register during initialization, so
ice_dpll_sw_pins_update() sees all pins as inactive and
ice_dpll_sw_pin_frequency_get() permanently returns 0 Hz for every
SW pin.
Fix this by writing a default SMA configuration in
ice_dpll_init_info_sw_pins(): clear all SMA bits, then set SMA1 and
SMA2 as active inputs (DIR_EN=0) with U.FL1 output and U.FL2 input
disabled. Each SMA/U.FL pair shares a physical signal path so only
one pin per pair can be active at a time. U.FL pins still report
frequency 0 after this fix: U.FL1 (output-only) is disabled by
ICE_SMA1_TX_EN which keeps the TX output buffer off, and U.FL2
(input-only) is disabled by ICE_SMA2_UFL2_RX_DIS. They can be
activated by changing the corresponding SMA pin direction via dpll
netlink.
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-7-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On certain E810 configurations where firmware supports Tx scheduler
topology switching (tx_sched_topo_comp_mode_en), ice_cfg_tx_topo()
may need to apply a new 5-layer or 9-layer topology from the DDP
package. If the AQ command to set the topology fails (e.g. due to
invalid DDP data or firmware limitations), the global configuration
lock must still be cleared via a CORER reset.
Commit 86aae43f21 ("ice: don't leave device non-functional if Tx
scheduler config fails") correctly fixed this by refactoring
ice_cfg_tx_topo() to always trigger CORER after acquiring the global
lock and re-initialize hardware via ice_init_hw() afterwards.
However, commit 8a37f9e2ff ("ice: move ice_deinit_dev() to the end
of deinit paths") later moved ice_init_dev_hw() into ice_init_hw(),
breaking the reinit path introduced by 86aae43f21. This creates an
infinite recursive call chain:
ice_init_hw()
ice_init_dev_hw()
ice_cfg_tx_topo() # topology change needed
ice_deinit_hw()
ice_init_hw() # reinit after CORER
ice_init_dev_hw() # recurse
ice_cfg_tx_topo()
... # stack overflow
Fix by moving ice_init_dev_hw() back out of ice_init_hw() and calling
it explicitly from ice_probe() and ice_devlink_reinit_up(). The third
caller, ice_cfg_tx_topo(), intentionally does not need ice_init_dev_hw()
during its reinit, it only needs the core HW reinitialization. This
breaks the recursion cleanly without adding flags or guards.
The deinit ordering changes from commit 8a37f9e2ff ("ice: move
ice_deinit_dev() to the end of deinit paths") which fixed slow rmmod
are preserved, only the init-side placement of ice_init_dev_hw() is
reverted.
Fixes: 8a37f9e2ff ("ice: move ice_deinit_dev() to the end of deinit paths")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-6-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ice_reset_all_vfs() ignores the return value of ice_vf_rebuild_vsi().
When the VSI rebuild fails (e.g. during NVM firmware update via
nvmupdate64e), ice_vsi_rebuild() tears down the VSI on its error path,
leaving txq_map and rxq_map as NULL. The subsequent unconditional call
to ice_vf_post_vsi_rebuild() leads to a NULL pointer dereference in
ice_ena_vf_q_mappings() when it accesses vsi->txq_map[0].
The single-VF reset path in ice_reset_vf() already handles this
correctly by checking the return value of ice_vf_reconfig_vsi() and
skipping ice_vf_post_vsi_rebuild() on failure.
Apply the same pattern to ice_reset_all_vfs(): check the return value
of ice_vf_rebuild_vsi() and skip ice_vf_post_vsi_rebuild() and
ice_eswitch_attach_vf() on failure. The VF is left safely disabled
(ICE_VF_STATE_INIT not set, VFGEN_RSTAT not set to VFACTIVE) and can
be recovered via a VFLR triggered by a PCI reset of the VF
(sysfs reset or driver rebind).
Note that this patch does not prevent the VF VSI rebuild from failing
during NVM update — the underlying cause is firmware being in a
transitional state while the EMP reset is processed, which can cause
Admin Queue commands (ice_add_vsi, ice_cfg_vsi_lan) to fail. This
patch only prevents the subsequent NULL pointer dereference that
crashes the kernel when the rebuild does fail.
crash> bt
PID: 50795 TASK: ff34c9ee708dc680 CPU: 1 COMMAND: "kworker/u512:5"
#0 [ff72159bcfe5bb50] machine_kexec at ffffffffaa8850ee
#1 [ff72159bcfe5bba8] __crash_kexec at ffffffffaaa15fba
#2 [ff72159bcfe5bc68] crash_kexec at ffffffffaaa16540
#3 [ff72159bcfe5bc70] oops_end at ffffffffaa837eda
#4 [ff72159bcfe5bc90] page_fault_oops at ffffffffaa893997
#5 [ff72159bcfe5bce8] exc_page_fault at ffffffffab528595
#6 [ff72159bcfe5bd10] asm_exc_page_fault at ffffffffab600bb2
[exception RIP: ice_ena_vf_q_mappings+0x79]
RIP: ffffffffc0a85b29 RSP: ff72159bcfe5bdc8 RFLAGS: 00010206
RAX: 00000000000f0000 RBX: ff34c9efc9c00000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000010 RDI: ff34c9efc9c00000
RBP: ff34c9efc27d4828 R8: 0000000000000093 R9: 0000000000000040
R10: ff34c9efc27d4828 R11: 0000000000000040 R12: 0000000000100000
R13: 0000000000000010 R14: R15:
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ff72159bcfe5bdf8] ice_sriov_post_vsi_rebuild at ffffffffc0a85e2e [ice]
#8 [ff72159bcfe5be08] ice_reset_all_vfs at ffffffffc0a920b4 [ice]
#9 [ff72159bcfe5be48] ice_service_task at ffffffffc0a31519 [ice]
#10 [ff72159bcfe5be88] process_one_work at ffffffffaa93dca4
#11 [ff72159bcfe5bec8] worker_thread at ffffffffaa93e9de
#12 [ff72159bcfe5bf18] kthread at ffffffffaa946663
#13 [ff72159bcfe5bf50] ret_from_fork at ffffffffaa8086b9
The panic occurs attempting to dereference the NULL pointer in RDX at
ice_sriov.c:294, which loads vsi->txq_map (offset 0x4b8 in ice_vsi).
The faulting VSI is an allocated slab object but not fully initialized
after a failed ice_vsi_rebuild():
crash> struct ice_vsi 0xff34c9efc27d4828
netdev = 0x0,
rx_rings = 0x0,
tx_rings = 0x0,
q_vectors = 0x0,
txq_map = 0x0,
rxq_map = 0x0,
alloc_txq = 0x10,
num_txq = 0x10,
alloc_rxq = 0x10,
num_rxq = 0x10,
The nvmupdate64e process was performing NVM firmware update:
crash> bt 0xff34c9edd1a30000
PID: 49858 TASK: ff34c9edd1a30000 CPU: 1 COMMAND: "nvmupdate64e"
#0 [ff72159bcd617618] __schedule at ffffffffab5333f8
#4 [ff72159bcd617750] ice_sq_send_cmd at ffffffffc0a35347 [ice]
#5 [ff72159bcd6177a8] ice_sq_send_cmd_retry at ffffffffc0a35b47 [ice]
#6 [ff72159bcd617810] ice_aq_send_cmd at ffffffffc0a38018 [ice]
#7 [ff72159bcd617848] ice_aq_read_nvm at ffffffffc0a40254 [ice]
#8 [ff72159bcd6178b8] ice_read_flat_nvm at ffffffffc0a4034c [ice]
#9 [ff72159bcd617918] ice_devlink_nvm_snapshot at ffffffffc0a6ffa5 [ice]
dmesg:
ice 0000:13:00.0: firmware recommends not updating fw.mgmt, as it
may result in a downgrade. continuing anyways
ice 0000:13:00.1: ice_init_nvm failed -5
ice 0000:13:00.1: Rebuild failed, unload and reload driver
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-5-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The V1 ADD_VLAN opcode had no success handler; filters sent via V1
stayed in ADDING state permanently. Add a fallthrough case so V1
filters also transition ADDING -> ACTIVE on PF confirmation.
Critically, add an `if (v_retval) break` guard: the error switch in
iavf_virtchnl_completion() does NOT return after handling errors,
it falls through to the success switch. Without this guard, a
PF-rejected ADD would incorrectly mark ADDING filters as ACTIVE,
creating a driver/HW mismatch where the driver believes the filter
is installed but the PF never accepted it.
For V2, this is harmless: iavf_vlan_add_reject() in the error
block already kfree'd all ADDING filters, so the success handler
finds nothing to transition.
Fixes: 968996c070 ("iavf: Fix VLAN_V2 addition/rejection")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-4-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The VLAN filter DELETE path was asymmetric with the ADD path: ADD
waits for PF confirmation (ADD -> ADDING -> ACTIVE), but DELETE
immediately frees the filter struct after sending the DEL message
without waiting for the PF response.
This is problematic because:
- If the PF rejects the DEL, the filter remains in HW but the driver
has already freed the tracking structure, losing sync.
- Race conditions between DEL pending and other operations
(add, reset) cannot be properly resolved if the filter struct
is already gone.
Add IAVF_VLAN_REMOVING state to make the DELETE path symmetric:
REMOVE -> REMOVING (send DEL) -> PF confirms -> kfree
-> PF rejects -> ACTIVE
In iavf_del_vlans(), transition filters from REMOVE to REMOVING
instead of immediately freeing them. The new DEL completion handler
in iavf_virtchnl_completion() frees filters on success or reverts
them to ACTIVE on error.
Update iavf_add_vlan() to handle the REMOVING state: if a DEL is
pending and the user re-adds the same VLAN, queue it for ADD so
it gets re-programmed after the PF processes the DEL.
The !VLAN_FILTERING_ALLOWED early-exit path still frees filters
directly since no PF message is sent in that case.
Also update iavf_del_vlan() to skip filters already in REMOVING
state: DEL has been sent to PF and the completion handler will
free the filter when PF confirms. Without this guard, the sequence
DEL(pending) -> user-del -> second DEL could cause the PF to return
an error for the second DEL (filter already gone), causing the
completion handler to incorrectly revert a deleted filter back to
ACTIVE.
Fixes: 968996c070 ("iavf: Fix VLAN_V2 addition/rejection")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-3-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a VF goes down, the driver currently sends DEL_VLAN to the PF for
every VLAN filter (ACTIVE -> DISABLE -> send DEL -> INACTIVE), then
re-adds them all on UP (INACTIVE -> ADD -> send ADD -> ADDING ->
ACTIVE). This round-trip is unnecessary because:
1. The PF disables the VF's queues via VIRTCHNL_OP_DISABLE_QUEUES,
which already prevents all RX/TX traffic regardless of VLAN filter
state.
2. The VLAN filters remaining in PF HW while the VF is down is
harmless - packets matching those filters have nowhere to go with
queues disabled.
3. The DEL+ADD cycle during down/up creates race windows where the
VLAN filter list is incomplete. With spoofcheck enabled, the PF
enables TX VLAN filtering on the first non-zero VLAN add, blocking
traffic for any VLANs not yet re-added.
Remove the entire DISABLE/INACTIVE state machinery:
- Remove IAVF_VLAN_DISABLE and IAVF_VLAN_INACTIVE enum values
- Remove iavf_restore_filters() and its call from iavf_open()
- Remove VLAN filter handling from iavf_clear_mac_vlan_filters(),
rename it to iavf_clear_mac_filters()
- Remove DEL_VLAN_FILTER scheduling from iavf_down()
- Remove all DISABLE/INACTIVE handling from iavf_del_vlans()
VLAN filters now stay ACTIVE across down/up cycles. Only explicit
user removal (ndo_vlan_rx_kill_vid) or PF/VF reset triggers VLAN
filter deletion/re-addition.
Fixes: ed1f5b58ea ("i40evf: remove VLAN filters on close")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-2-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename the IAVF_VLAN_IS_NEW state to IAVF_VLAN_ADDING to better
describe what the state represents: an ADD request has been sent to
the PF and is waiting for a response.
This is a pure rename with no behavioral change, preparing for a
cleanup of the VLAN filter state machine.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-1-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Eric Biggers says:
====================
Reimplement TCP-AO using crypto library
This series can also be retrieved from:
git fetch https://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux.git tcp-ao-v2
This series is targeting net-next for 7.2. To make this series
self-contained in the networking code, I dropped the patches that remove
support for transformation cloning from the crypto API, which is a
further negative 275-line cleanup and optimization this series enables.
That will be done as a follow-up, either through the crypto tree for
7.3, or still through net-next for 7.2 at maintainer preference.
This series refactors the TCP-AO (TCP Authentication Option) code to do
MAC and KDF computations using lib/crypto/ instead of crypto_ahash.
This greatly simplifies the code and makes it much more efficient. The
entire tcp_sigpool mechanism becomes unnecessary and is removed, as the
problems it was designed to solve don't exist with the library APIs.
The crypto API's support for crypto transformation cloning also becomes
unnecessary and will be removed in follow-up patches. Note that as part
of that, we'll be able to roll back the addition of the reference count
to crypto_tfm, which had regressed performance for all crypto API users.
To make this simplification and optimization possible, this series also
updates the TCP-AO code to support a specific set of algorithms, rather
than arbitrary algorithms that don't make sense and are very likely not
being used, e.g. CRC-32 and HMAC-MD5.
Specifically, this series retains the support for AES-128-CMAC,
HMAC-SHA1, and HMAC-SHA256. AES-128-CMAC and HMAC-SHA1 are the only
algorithms that are actually standardized for use in TCP-AO, while
HMAC-SHA256 makes sense to continue supporting as a Linux extension. Of
course, other algorithms can still be (re-)added later if ever needed.
It's worth noting that TCP-AO MACs are limited to 20 bytes by the TCP
options space, which limits the benefit of further algorithm upgrades.
This series passes the tcp_ao selftests
(sudo make -C tools/testing/selftests/net/tcp_ao/ run_tests).
To get a sense for how much more efficient this makes the TCP-AO code,
here's a microbenchmark for tcp_ao_hash_skb() with skb->len == 128:
Algorithm Avg cycles (before) Avg cycles (after)
--------- ------------------- ------------------
HMAC-SHA1 3319 1256
HMAC-SHA256 3311 1344
AES-128-CMAC 2720 1107
====================
Link: https://patch.msgid.link/20260427172727.9310-1-ebiggers@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
tcp_sigpool is no longer used. It existed only as a workaround for
issues in the design of the crypto_ahash API, which have been avoided by
switching to the much easier-to-use library APIs instead. Remove it.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20260427172727.9310-6-ebiggers@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since tcp-ao now uses the crypto library API instead of crypto_ahash,
and MACs and keys now have a statically-known maximum size, many tcp-ao
functions can no longer fail. Propagate this change up into the return
types of various functions.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20260427172727.9310-5-ebiggers@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that the maximum MAC and traffic key lengths are statically-known
small values, allocate MACs and traffic keys on the stack instead of
with kmalloc. This eliminates multiple failure-prone GFP_ATOMIC
allocations.
Note that some cases such as tcp_ao_prepare_reset() are left unchanged
for now since they would require slightly wider changes.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20260427172727.9310-4-ebiggers@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently the kernel's TCP-AO implementation does the MAC and KDF
computations using the crypto_ahash API. This API is inefficient and
difficult to use, and it has required extensive workarounds in the form
of per-CPU preallocated objects (tcp_sigpool) to work at all.
Let's use lib/crypto/ instead. This means switching to straightforward
stack-allocated structures, virtually addressed buffers, and direct
function calls. It also means removing quite a bit of error handling.
This makes TCP-AO quite a bit faster.
This also enables many additional cleanups, which later commits will
handle: removing tcp-sigpool, removing support for crypto_tfm cloning,
removing more error handling, and replacing more dynamically-allocated
buffers with stack buffers based on the now-statically-known limits.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20260427172727.9310-3-ebiggers@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
RFC 5926 (https://datatracker.ietf.org/doc/html/rfc5926) specifies the
use of AES-128-CMAC and HMAC-SHA1 with TCP-AO. This includes a
specification for how traffic keys shall be derived for each algorithm.
Support for any other algorithms with TCP-AO isn't standardized, though
an expired Internet Draft (a work-in-progress document, not a standard)
from 2019 does propose adding HMAC-SHA256 support:
https://datatracker.ietf.org/doc/html/draft-nayak-tcp-sha2-03
Since both documents specify the KDF for each algorithm individually, it
isn't necessarily clear how any other algorithm should be integrated.
Nevertheless, the Linux implementation of TCP-AO allows userspace to
specify the MAC algorithm as a string tcp_ao_add::alg_name naming either
"cmac(aes128)" or an arbitrary algorithm in the crypto_ahash API. The
set of valid strings is undocumented. The implementation assumes that
"cmac(aes128)" is the only algorithm that requires an entropy extraction
step and that all algorithms accept keys with length equal to the
untruncated MAC; thus, arbitrary HMAC algorithms probably do work, but
some other MAC algorithms like AES-256-CMAC have never actually worked.
Unfortunately, this undocumented string allows many obsolete, insecure,
or redundant algorithms. For example, "hmac(md5)" and the
non-cryptographic "crc32" are accepted. It also ties the implementation
to crypto_ahash and requires that most memory be dynamically allocated,
making the implementation unnecessarily complex and inefficient. Still
furthermore, this implementation requires the crypto API to support
"transformation cloning", whose only user is this feature.
Fortunately, it's very likely that only a few algorithms are actually
used in practice. Let's restrict the set of allowed algorithms to
"cmac(aes128)" (or "cmac(aes)" with keylen=16), "hmac(sha1)", and
"hmac(sha256)". The first two are the actually standard ones, while
HMAC-SHA256 seems like a reasonable algorithm to continue supporting as
a Linux extension, considering the Internet Draft for it and the fact
that SHA-256 is the usual choice of upgrade from the outdated SHA-1.
If any other algorithm ever turns out to be needed, e.g. HMAC-SHA512, it
can of course be (re-)added in library form. However, note that the TCP
options space limits TCP-AO MACs to 20 bytes (160 bits) anyway, which
limits the potential benefit of any further upgrade to the algorithm.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20260427172727.9310-2-ebiggers@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- Fix inverted check of registering the stats for branch tracing
When calling register_stat_tracer() which returns zero on success and
negative on error, the callers were checking the return of zero as an
error and printing a warning message. Because this was just a normal
printk() message and not a WARN(), it wasn't caught in any testing.
Fix the check to print the warning message when an error actually happens.
- Fix a typo in a comment in tracepoint.h
- Limit the size of event probes to 3K in size
It is possible to create a dynamic event probe via the tracefs system that
is greater than the max size of an event that the ring buffer can hold.
This basically causes the event to become useless. Limit the size of an
event probe to be 3K as that should be large enough to handle any dynamic
events being created, and fits within the PAGE_SIZE sub-buffers of the
ring buffer.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCafJn9hQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6quUaAP9ezC2VXWugRIhOEmK0pIpY90zddsyv
xYTa3XuPP2r5JQEA8DcmH6fTo7JJxzbbyWPot/EgaqMt5XguqKC7txhjfww=
=+e7q
-----END PGP SIGNATURE-----
Merge tag 'trace-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix inverted check of registering the stats for branch tracing
When calling register_stat_tracer() which returns zero on success and
negative on error, the callers were checking the return of zero as an
error and printing a warning message. Because this was just a normal
printk() message and not a WARN(), it wasn't caught in any testing.
Fix the check to print the warning message when an error actually
happens.
- Fix a typo in a comment in tracepoint.h
- Limit the size of event probes to 3K in size
It is possible to create a dynamic event probe via the tracefs system
that is greater than the max size of an event that the ring buffer
can hold. This basically causes the event to become useless.
Limit the size of an event probe to be 3K as that should be large
enough to handle any dynamic events being created, and fits within
the PAGE_SIZE sub-buffers of the ring buffer.
* tag 'trace-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/probes: Limit size of event probe to 3K
tracepoint: Fix typo in tracepoint.h comment
tracing: branch: Fix inverted check on stat tracer registration
When page_pool_create_percpu() fails on page_pool_list(), it falls
through to its err_uninit: label, which calls page_pool_uninit().
At that point page_pool_init() has already taken two references
when the user requested PP_FLAG_ALLOW_UNREADABLE_NETMEM:
pool->mp_ops->init(pool)
static_branch_inc(&page_pool_mem_providers);
Neither is undone by page_pool_uninit(); both are only undone by
__page_pool_destroy() (success-side teardown). The error path
therefore leaks the per-provider reference taken by mp_ops->init
(io_zcrx_ifq->refs in the io_uring zcrx provider, the dmabuf
binding refcount in the devmem provider) plus one increment of
the page_pool_mem_providers static branch on every failure of
xa_alloc_cyclic() inside page_pool_list().
The leaked io_zcrx_ifq->refs in turn pins everything
io_zcrx_ifq_free() would release on cleanup: ifq->user (uid),
ifq->mm_account (mmdrop), ifq->dev (device refcount),
ifq->netdev_tracker (netdev refcount), and the rbuf region.
The leaked static branch increment forces all subsequent
page_pool_alloc_netmems() and page_pool_return_page() callers to
take the slow mp_ops branch for the lifetime of the kernel.
Reachable via the io_uring zcrx path:
io_uring_register(IORING_REGISTER_ZCRX_IFQ) /* CAP_NET_ADMIN */
-> __io_uring_register
-> io_register_zcrx
-> zcrx_register_netdev
-> netif_mp_open_rxq
-> driver ndo_queue_mem_alloc
-> page_pool_create_percpu
-> page_pool_init succeeds (mp_ops->init runs, branch++)
-> page_pool_list fails (xa_alloc_cyclic -ENOMEM)
-> goto err_uninit <-- leak
The same shape applies to the devmem dmabuf provider via
mp_dmabuf_devmem_init()/mp_dmabuf_devmem_destroy().
Restore the cleanup symmetry by moving the mp_ops->destroy() and
static_branch_dec() calls out of __page_pool_destroy() and into
page_pool_uninit(), so page_pool_uninit() is again the strict
inverse of page_pool_init(). page_pool_uninit() has only two
callers (the err_uninit: path and __page_pool_destroy()), so this
preserves the single-call invariant on the success path while
fixing the err path. The error path of page_pool_init() itself
still skips the mp_ops cleanup correctly: mp_ops->init is the
last action that takes a reference before page_pool_init() returns
0, so when it returns an error neither the refcount nor the static
branch has been touched.
Triggering the bug requires xa_alloc_cyclic() to fail with -ENOMEM,
which under normal GFP_KERNEL retry behaviour is rare. It is
deterministic under CONFIG_FAULT_INJECTION with fail_page_alloc /
xa fault injection, or under sustained memory pressure. The leak
is silent: there is no warning, and the released kernel build
continues running with a permanently-incremented static branch.
Fixes: 0f92140468 ("memory-provider: dmabuf devmem memory provider")
Signed-off-by: Hasan Basbunar <basbunarhasan@gmail.com>
Link: https://patch.msgid.link/20260428170739.34881-1-basbunarhasan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Always complete the airoha_dev_stop() routine regardless of the
airoha_set_vip_for_gdm_port() return value, since errors from
ndo_stop() are ignored by the networking stack and the interface is
always considered down after the call.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260428-airoha-ndo-stop-not-err-v1-1-674506d29a91@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
OF_GPIO is selected automatically on all OF systems. Any symbols it
controls also provide stubs so there's really no reason to select it
explicitly.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260428093338.35043-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
