The sync command worker holds hdev->req_lock, but inquiry-cache updates
and flushes use hdev->lock. Both hci_acl_create_conn_sync() and
hci_stop_discovery_sync() look up entries and read their fields without
taking hdev->lock.
After either lookup returns, a concurrent HCIINQUIRY ioctl can acquire
hdev->lock and flush the cache, freeing the entry. The worker then reads
the freed entry while preparing a create-connection or remote-name-cancel
command. The list traversal also races with cache updates and removal.
KASAN reported these accesses:
BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0x5f1/0x650
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_acl_create_conn_sync+0x5f1/0x650
hci_cmd_sync_work+0x13c/0x290
Allocated by task 90:
hci_inquiry_cache_update+0x3e6/0x7d0
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 93:
hci_inquiry_cache_flush+0x111/0x2b0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
BUG: KASAN: slab-use-after-free in hci_stop_discovery_sync+0x3b1/0x3c0
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_stop_discovery_sync+0x3b1/0x3c0
hci_cmd_sync_work+0x173/0x300
Allocated by task 86:
hci_inquiry_cache_update+0x483/0x940
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 91:
hci_inquiry_cache_flush+0x13e/0x2f0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
Hold hdev->lock across each lookup and all reads from its result. Copy the
remote address before unlocking so discovery cancellation does not retain
a cache entry pointer. Release the lock before sending synchronous HCI
commands, since their completion handlers may need the same lock.
Fixes: cf75ad8b41 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED")
Fixes: 45340097ce ("Bluetooth: hci_conn: Only do ACL connections sequentially")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_unregister_dev() disables cmd_work and cmd_timer, then calls
hci_cmd_sync_clear(), whose cancel_work_sync() waits for
hci_cmd_sync_work() to return. That worker dequeues and runs every
entry on cmd_sync_work_list. With cmd_work disabled nothing reaches
the controller, so each queued HCI command waits the full
HCI_CMD_TIMEOUT (2s).
The backlog has no bound. Userspace can keep queuing MGMT commands
such as MGMT_OP_GET_CLOCK_INFO against a controller that doesn't
answer. Closing /dev/vhci then blocks in vhci_release() for
backlog * 2s:
INFO: task syz-executor:5749 blocked for more than 143 seconds.
cancel_work_sync
hci_cmd_sync_clear
hci_unregister_dev
vhci_release
In a local reproduction the backlog held more than 5000 entries,
which comes to hours of hang.
Stop the worker from taking new entries once HCI_UNREGISTER is set,
and wake any request still waiting with -ENODEV before cancelling
the work. The entries left over are destroyed with -ECANCELED by the
existing sweep in hci_cmd_sync_clear(). They stay on the list until
the work has stopped, so hci_cmd_sync_dequeue() and friends still see
them. A callback already running may still issue another command,
which delays unregister by at most one timeout per remaining command,
not by the whole backlog.
Fixes: 008ee9eb8a ("Bluetooth: hci_sync: Fix not processing all entries on cmd_sync_work")
Reported-by: syzbot+217e3f1283cafe80586e@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=217e3f1283cafe80586e
Signed-off-by: Nguyen Ngoc Thang <ngocthang2710.1999@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The fragmented path in hci_queue_iso() calls __skb_queue_tail() without
holding conn->data_q.lock. The socket lock serializes senders, but the
transmit worker can concurrently remove packets from this queue using
skb_dequeue().
After an insertion saves the old tail pointer, hci_sched_iso() can dequeue
that packet and pass it to the driver. The driver can free the packet
before the insertion resumes and writes to the old tail's next pointer,
causing a use-after-free. Concurrent updates can also corrupt the queue.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_send_iso+0xc7d/0xe10
Call Trace:
hci_send_iso+0xc7d/0xe10
iso_sock_sendmsg+0x710/0x900
__sys_sendto+0x34a/0x3a0
Allocated by task 86:
__alloc_skb+0xdd/0x820
alloc_skb_with_frags+0x7e/0x770
sock_alloc_send_pskb+0x67a/0x820
bt_skb_sendmsg.constprop.0+0xc0/0x6c0
iso_sock_sendmsg+0x44e/0x900
Freed by task 90:
kmem_cache_free+0xcb/0x3d0
vhci_read+0x33f/0x4d0
vfs_read+0x177/0xa20
Hold the queue lock across the entire fragment batch, as hci_queue_acl()
does, to serialize insertion against dequeue while preserving fragment
ordering.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth: hci_conn: Lock parent access during enhanced SCO setup
hci_enhanced_setup_sync() runs on the request workqueue without the
hci_dev_lock held by its caller when setup was queued. Its CVSD
capability check and find_next_esco_param() dereference conn->parent
while the receive workqueue can unlink and release that parent.
The following interleaving can cause a use-after-free:
hci_enhanced_setup_sync() hci_disconn_complete_evt()
load conn->parent
hci_dev_lock()
hci_conn_del(ACL parent)
unlink SCO child
drop link's parent reference
clear child->parent
release ACL parent
bt_link_release()
kfree(parent)
hci_dev_unlock()
read parent->features[0][3]
The reference held for the queued SCO child does not keep its ACL parent
alive after unlinking. Commit 42de40abe2 ("Bluetooth: hci_conn: fix the
SCO setup context lifetime") protects the child stored in the queued
context, but leaves these parent accesses unprotected.
With a 40 ms diagnostic delay after loading conn->parent, an instrumented
kernel based on fd179f8a05, which already contains 42de40abe2,
reported:
BUG: KASAN: slab-use-after-free in hci_enhanced_setup_sync+0xda5/0xdf0
Read of size 1 at addr ffff888102204047 by task kworker/u17:0/93
Call Trace:
hci_enhanced_setup_sync+0xda5/0xdf0
hci_cmd_sync_work+0x13c/0x290
process_one_work+0x6b4/0x10e0
Allocated by task 92:
__hci_conn_add+0x304/0x1df0
hci_connect_acl+0x349/0x3e0
hci_connect_sco+0x3b/0x9a0
sco_sock_connect+0x475/0xca0
Freed by task 94:
kfree+0x121/0x3c0
bt_link_release+0x79/0xa0
device_release+0xc8/0x240
kobject_put+0x14d/0x280
hci_conn_del+0x524/0xe30
hci_disconn_complete_evt+0x403/0x8c0
hci_event_packet+0x71b/0xb20
hci_rx_work+0x293/0x730
The accessed address is 71 bytes into the freed ACL parent, at its
features[0][3] byte; the queued SCO child is a different object. The
diagnostic preserves the loaded parent across the delay, matching the
unmodified compiled capability check, and does not change the parent
references or teardown path.
Hold hci_dev_lock() across the codec switch, including every call to
find_next_esco_param(), and release it on all selection errors. Keep
configure_datapath_sync() outside the critical section because it waits
for HCI events. Preserve parameter selection and existing return values.
Fixes: e07a06b4eb ("Bluetooth: Convert SCO configure_datapath to hci_sync")
Cc: stable@vger.kernel.org
Assisted-by: GPT-6-Astra
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Parse DDC record lengths in unsigned storage so 0xFF does not wrap.
Reject records smaller than the mandatory three-byte header, records
exceeding U8_MAX, and records exceeding remaining firmware bytes before
issuing Intel_Write_DDC.
This issue was reported by Claude Mythos.
Fixes: 145f2368c5 ("Bluetooth: btintel: Add Device Configuration support")
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_register_dev() allocates an ID before calling dev_set_name().
If naming fails, it returns without releasing that ID. The device has
not been registered and hdev->id has not been assigned, so the normal
unregister path cannot release it.
Free the allocated ID before returning the naming error.
Fixes: dcda165706 ("Bluetooth: hci_core: Fix build warnings")
Reported-by: Changyul Lee <lcy8047@gmail.com>
Assisted-by: LLM
Signed-off-by: Sang-Hoon Choi <csh0052@gmail.com>
Reported-by: Changyul Lee <lcy8047@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On 64-bit systems, outgoing BR/EDR connections always fall back to page
scan repetition mode R2 with no clock offset once the system has been
up for more than five minutes, even when inquiry found the peer only
seconds earlier. This lengthens paging and can increase the risk of a
Page Timeout.
The inquiry cache stores jiffies in __u32 timestamps, but its age
helpers subtract them from unsigned long jiffies. INITIAL_JIFFIES casts
-300 * HZ through unsigned int, so jiffies crosses 2^32 five minutes
after boot on 64-bit systems. Assigning it to __u32 then drops the upper
32 bits. In one trace, a 7.6-second-old entry (HZ=1000) was reported as
2^32 + 7620 ticks old and rejected by hci_acl_create_conn_sync().
hci_inquiry() is affected by the same truncation when checking the whole
cache. 32-bit systems are unaffected because unsigned long is 32 bits
wide there.
Use unsigned long for both timestamps so they have the same width as
jiffies on 32-bit and 64-bit systems, and update the debugfs format
specifier accordingly.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btintel_pcie_send_frame() eventually copies skb->data into a fixed
BTINTEL_PCIE_BUFFER_SIZE (4096) DMA buffer via memcpy() in
btintel_pcie_prepare_tx(), with a 4-byte PCIe type header prepended.
A user-space process with HCI_CHANNEL_USER access can inject an
oversized packet and overflow the buffer.
Reject packets larger than
BTINTEL_PCIE_BUFFER_SIZE - BTINTEL_PCIE_HCI_TYPE_LEN on entry.
Fixes: 6e65a09f92 ("Bluetooth: btintel_pcie: Add *setup* function to download firmware")
Cc: stable@vger.kernel.org
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
plen is u16 and computed as HDR_SIZE + dlen. For ACL/ISO frames dlen
is a 16-bit field, so a value >= 0xFFFC wraps the sum, bypassing the
"skb->len < plen" check and letting skb_trim() truncate the packet.
Widen plen to u32 so the addition cannot wrap.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Cc: stable@vger.kernel.org
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The "Exception info %s" print uses skb->data + 1, but the 12-byte
payload is not guaranteed to be NUL-terminated and can be read past
its end.
Bound the print with "%.*s" and skb->len - 1.
Fixes: 973bb97e5a ("Bluetooth: btintel: Add generic function for handling hardware errors")
Cc: stable@vger.kernel.org
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
While rfcomm_recv_frame() verifies that skb->len is at least
sizeof(*hdr) + 1 (4 bytes: 3-byte header + 1-byte FCS), an RFCOMM frame
with an extended 2-byte length field (!__test_ea(hdr->len)) has a 4-byte
header plus a 1-byte FCS (5 bytes minimum, sizeof(*hdr) + 2).
When a 4-byte RFCOMM frame with EA == 0 arrives:
1. The initial skb->len < sizeof(*hdr) + 1 check passes (4 < 4 is false).
2. Trimming the FCS byte decrements skb->len to 3.
3. If __check_fcs() succeeds, skb_pull(skb, 4) fails (4 > 3) and returns
NULL without advancing skb->data.
4. Because the return value of skb_pull() is ignored, the un-pulled
3-byte struct rfcomm_hdr remains at skb->data and is either queued as
application payload via rfcomm_recv_data() or parsed as a multiplexer
control command via rfcomm_recv_mcc() on DLCI 0.
Fix this by extending the length check in rfcomm_recv_frame() to also
require skb->len >= sizeof(*hdr) + 2 when !__test_ea(hdr->len).
Fixes: b230e5bf50 ("Bluetooth: RFCOMM: validate skb length in rfcomm_recv_frame")
Assisted-by: LLM
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The RFCOMM_CONNINFO getsockopt handler accepts a socket that is not
connected as long as deferred setup is enabled:
if (sk->sk_state != BT_CONNECTED &&
!rfcomm_pi(sk)->dlc->defer_setup) {
err = -ENOTCONN;
break;
}
l2cap_sk = rfcomm_pi(sk)->dlc->session->sock->sk;
dlc->defer_setup is set in rfcomm_sock_init() when rfcomm_connect_ind()
creates a child socket for an incoming connection on a listening socket
that has BT_DEFER_SETUP enabled. It is never cleared afterwards. The
session, however, can go away underneath it.
rfcomm_recv_disc() forces the dlc state before tearing it down:
d->state = BT_CLOSED;
__rfcomm_dlc_close(d, err);
The RFCOMM_DEFER_SETUP early return in __rfcomm_dlc_close() only covers
BT_CONNECT, BT_CONFIG, BT_OPEN and BT_CONNECT2, so with the state
already BT_CLOSED that switch does not match and the function falls
through to rfcomm_dlc_unlink(), which sets d->session = NULL, while
d->defer_setup stays 1.
A getsockopt(SOL_RFCOMM, RFCOMM_CONNINFO) on the accepted socket after
that point therefore skips the -ENOTCONN path -- sk->sk_state is
BT_CLOSED, but dlc->defer_setup is still set -- and dereferences the
NULL session. No race is needed: once the DISC has been processed, the
dereference is unconditional.
Reproduced on a KASAN kernel under QEMU with a BR/EDR peer emulated over
/dev/vhci: the peer brings up an ACL link, opens L2CAP on the RFCOMM
PSM, starts a session and sends SABM for a channel bound with
BT_DEFER_SETUP, and sends DISC for that dlci after the socket has been
accepted. getsockopt(SOL_RFCOMM, RFCOMM_CONNINFO) on the accepted
socket then hits:
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000002: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 1 UID: 0 PID: 150 Comm: init Tainted: G B 7.3.0-rc3-g5dd1818b15d9
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:rfcomm_sock_getsockopt+0x529/0x780
Call Trace:
<TASK>
do_sock_getsockopt+0x3ad/0x7d0
__sys_getsockopt+0x10e/0x1b0
__x64_sys_getsockopt+0xc2/0x160
do_syscall_64+0xda/0x4b0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
0x10 is the offset of sock in struct rfcomm_session;
rfcomm_sock_getsockopt_old() is inlined into rfcomm_sock_getsockopt().
Commit 43a556b2fd ("Bluetooth: RFCOMM: take rfcomm_mutex for the
deferred setup accept") fixed the same "a remote DISC clears the session
while deferred setup is still flagged" problem in rfcomm_dlc_accept();
this is the remaining instance of it, in the getsockopt path.
Deferred setup only leaves a socket usable here once it has reached
BT_CONNECT2, so restrict the exception to that state and check that a
session is actually present before following it.
Fixes: bb23c0ab82 ("Bluetooth: Add support for deferring RFCOMM connection setup")
Cc: stable@vger.kernel.org
Assisted-by: LLM
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In btintel_pcie_msix_rx_handle(), the driver processes RX completion
descriptors (urbd1) written by the PCIe device into DMA-coherent memory.
urbd1->frbd_tag (a 16-bit field fully controlled by the device firmware
via DMA) is used directly as an array index into rxq->bufs[] without any
bounds check. rxq->bufs[] has only BTINTEL_PCIE_RX_DESCS_COUNT (64)
entries, while frbd_tag can be any value 0-65535. A malicious or
malfunctioning device can write an out-of-range frbd_tag, causing the
driver to dereference an out-of-bounds data_buf pointer.
Additionally, cr_hia is read from a DMA-shared index array also writable
by the device; if the device sets cr_hia >= rxq->count, the while-loop
never terminates because cr_tia is wrapped via modulo rxq->count and can
never equal an out-of-range cr_hia.
Add bounds validation for cr_hia and frbd_tag in the RX path, and cr_hia
in the TX path. Log invalid values with bt_dev_err before returning.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix multiple out-of-bounds reads in Bluetooth BNEP frame processing:
1. In bnep_rx_frame() and bnep_ctrl_frame() (net/bluetooth/bnep/core.c),
use pskb_may_pull() to verify the BNEP header, control type byte,
filter count, and extension headers exist before reading them, and
return 0 after handling BNEP_CONTROL instead of falling through to
Ethernet frame submission when no extension headers follow.
2. In bnep_net_xmit() (net/bluetooth/bnep/netdev.c), verify skb->len >=
ETH_HLEN with pskb_may_pull() before reading the 14-byte Ethernet
header to prevent an out-of-bounds heap read and infoleak on short
AF_PACKET TX frames.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Assisted-by: LLM
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
read_unconf_index_list() counts unconfigured controllers before allocating
its response, then checks the device flags again while filling it.
hci_dev_list_lock stabilizes list membership, but it does not serialize the
per-device flags. During asynchronous controller setup, the worker can set
HCI_UNCONFIGURED and clear HCI_SETUP between the two passes. A controller
omitted from the allocation count can then become eligible for the fill
pass, causing an out-of-bounds write to rp->index[].
Allocate space for every device on hci_dev_list. Since list membership
cannot change while hci_dev_list_lock is held, the response remains large
enough regardless of flag transitions. The reported count and response
length still include only eligible unconfigured controllers.
Fixes: 73d1df2a7a ("Bluetooth: Add support for Read Unconfigured Index List command")
Cc: stable@vger.kernel.org
Signed-off-by: Aldo Ariel Panzardo <qwe.aldo@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
l2cap_data_rcv() unpacks either a two-byte or four-byte control field
without first ensuring that it is present. A short ERTM or streaming-mode
frame can therefore cause an out-of-bounds read.
There is a second short-frame case when CRC16 is enabled. After the
control field is pulled, l2cap_check_fcs() subtracts two from skb->len
without checking it. If fewer than two bytes remain, the subtraction
wraps; skb_trim() leaves the buffer unchanged and the subsequent FCS
load reads past the logical end of the frame.
Validate that the frame contains both its control field and, when
enabled, its FCS before either field is accessed.
Fixes: 1c2acffb76 ("Bluetooth: Add initial support for ERTM packets transfers")
Fixes: fcc203c30d ("Bluetooth: Add support for FCS option to L2CAP")
Cc: stable@vger.kernel.org
Signed-off-by: Aldo Ariel Panzardo <qwe.aldo@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_conn_link() takes a lifetime reference to its parent with
hci_conn_get(), but only takes an operational hold on the child.
hci_conn_unlink() later balances both a hold and a reference on the
parent.
The SCO and CIS paths pass a parent acquired from a connect helper, so
it already has a hold. For an additional BIS, hci_bind_bis() obtains the
parent from hci_conn_hash_lookup_big(), which returns a bare pointer.
Unlinking the child then drops the parent's existing hold and can
schedule it for disconnection while its socket is still using it.
Take a hold on the parent before linking it and drop that hold if linking
fails. A successful link transfers the hold to hci_conn_unlink().
Fixes: fa224d0c09 ("Bluetooth: ISO: Reassociate a socket with an active BIS")
Cc: stable@vger.kernel.org
Signed-off-by: Aldo Ariel Panzardo <qwe.aldo@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
is_filtered_packet() reads the event code from skb->data[0] without first
checking that the skb is nonempty. When an opcode filter is configured,
it also reads the command opcode at offsets 3 or 4 without checking that
a Command Complete or Command Status event is long enough.
hci_send_to_sock() invokes the filter before hci_event_packet() validates
the event header. A malformed event supplied by a controller or a vhci
device can therefore cause an out-of-bounds read.
Keep the unmasked event code for the opcode checks. The masked value is
needed for the 64-bit event bitmap, but using it to identify command events
aliases event codes above 0x3f. In particular, Synchronous Train Complete
(0x4f) was treated as Command Status (0x0f) even though its payload has no
opcode.
Reject actual command events that are too short for the field being
inspected. A truncated command event cannot match a configured opcode.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Aldo Ariel Panzardo <qwe.aldo@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The raw HCI socket security filter has 128 OCF bits per supported OGF,
but masks the 10-bit OCF with 127 before looking up the command. An
unprivileged socket can therefore submit a reserved OCF that aliases an
allowlisted command modulo 128.
A conforming controller should reject reserved opcodes. Nevertheless,
the security decision must apply to the opcode that will actually be
sent, especially since controller-specific behavior is outside the host
stack's control.
Reject OCF values that cannot be represented by the security filter
instead of aliasing them onto an unrelated command.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Aldo Ariel Panzardo <qwe.aldo@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_bind_cis() and hci_connect_cis() return one hci_conn hold for the
ISO layer. A new channel association consumes that hold, which is
eventually released by iso_conn_free().
There are two cases where iso_chan_add() does not create an association:
it returns success when the socket is already attached to the same
iso_conn, and it returns -EBUSY when another socket is attached. The
hold returned for the current call is unused in both cases. This occurs
when deferred setup calls iso_connect_cis() again for its existing
socket, or when another socket attempts to reuse the CIS.
Detect the idempotent case while the connection is locked and release
the unused hold after iso_chan_add(). Also release it on -EBUSY. Do not
drop it for other errors: a newly allocated iso_conn releases the
transferred hold when its last temporary reference is put.
Fixes: 69997d50ec ("Bluetooth: ISO: handle bound CIS cleanup via hci_conn")
Cc: stable@vger.kernel.org
Signed-off-by: Aldo Ariel Panzardo <qwe.aldo@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 69997d50ec ("Bluetooth: ISO: handle bound CIS cleanup via
hci_conn") made hci_bind_cis() and hci_connect_cis() return a
connection with one hold for the ISO layer. hci_bind_cis() currently
takes that hold only after configuring a CIS, so its BT_CONNECTED and
matching BT_BOUND paths return a bare lookup result. Its configuration
failure path can likewise call hci_conn_drop() before taking a hold.
Take the hold before any state-dependent return or configuration error
so every successful return follows the documented ownership contract
and every error drop is balanced.
hci_connect_cis() also assumes hci_conn_link() always takes a new CIS
hold before dropping the one returned by hci_bind_cis(). However, the
helper returns an existing link without taking another hold. In that
case, preserve the CIS hold for the caller and drop the redundant LE
hold because the existing link already owns its parent hold. Returning
early also avoids changing an existing CIS back to BT_CONNECT.
Fixes: 69997d50ec ("Bluetooth: ISO: handle bound CIS cleanup via hci_conn")
Cc: stable@vger.kernel.org
Signed-off-by: Aldo Ariel Panzardo <qwe.aldo@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In send_cancel(), pending mesh_tx objects are removed from the
hdev->mesh_pending list and freed via mesh_send_complete(). However, if
a mesh transmission was already queued onto hdev->cmd_sync_work_list via
mesh_next(), the queued entry retains a raw pointer to mesh_tx.
When hci_cmd_sync_work later processes the entry, it attempts to execute
mesh_send_sync and its destroy callback mesh_send_start_complete using
the already freed mesh_tx pointer, leading to a use-after-free.
Fix this by invoking hci_cmd_sync_dequeue() for mesh_send_sync on the
target mesh_tx before completing it. If the entry is found and dequeued,
its destroy callback will complete and free the object; otherwise,
mesh_send_complete() is called directly.
Additionally, ensure the transmission queue advances after cancellation
or errors. In mesh_send_start_complete(), call mesh_next() on error
unless err is -ECANCELED, because hci_cmd_sync_dequeue() holds
hdev->cmd_sync_work_lock and calling mesh_next() synchronously would
deadlock. Instead, advance the queue in send_cancel() once the lock is
released and if no transmission is in progress.
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When CONFIG_DEV_COREDUMP=n, hci_devcd_append() returns -EOPNOTSUPP
without freeing its skb argument. This leaks the cloned skb and also
prevents nxp_set_ind_reset() from being called to perform recovery.
Fix by guarding the hci_devcd_append(hdev, skb_clone(skb, GFP_ATOMIC))
call with IS_ENABLED(CONFIG_DEV_COREDUMP).
Fixes: 998e447f44 ("Bluetooth: btnxpuart: Add support for HCI coredump feature")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bose QC Ultra Headphones (dual-mode, same public address on both
transports) occasionally send an SMP Security Request on the BR/EDR
SMP fixed channel right after the ACL link is encrypted. The kernel
handles it as if it were an LE link: smp_cmd_security_req() has no
transport check, smp_ltk_encrypt() looks up an LTK with the ACL
connection's dst_type, and hci_find_ltk() matches the peer's LE LTK
because the LE public address type is stored as ADDR_LE_DEV_PUBLIC (0),
the same value as BDADDR_BREDR. HCI_OP_LE_START_ENC is then issued on
the ACL handle, the controller rejects it with Invalid HCI Command
Parameters, and hci_cs_le_start_enc() disconnects the link with
HCI_ERROR_AUTH_FAILURE. The headphones drop within a second of
connecting, before any profile is up; a manual reconnect works.
btmon (MediaTek MT7922, kernel 7.0.12):
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 50 Address: BC:87:FA:47:73:5E (Bose Corporation)
Encryption: Enabled with AES-CCM (0x02)
> ACL Data RX: Handle 50 flags 0x02 dlen 6
BR/EDR SMP: Security Request (0x0b) len 1
Authentication requirement: No bonding, No MITM, SC (0x08)
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
Handle: 50 Address: BC:87:FA:47:73:5E (Bose Corporation)
> HCI Event: Command Status (0x0f) plen 4
LE Start Encryption (0x08|0x0019) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 50 Address: BC:87:FA:47:73:5E (Bose Corporation)
Reason: Authentication Failure (0x05)
SMP over BR/EDR is limited to cross-transport key derivation; the
Security Request procedure (Core Specification Vol 3, Part H, Section
2.4.6, PDU in Section 3.6.7) has no BR/EDR counterpart. Reply with
Pairing Failed / Command Not Supported on a non-LE link, before the PDU
is parsed, and keep the connection. The reply is sent directly rather
than through smp_failure(): rejecting a command on the wrong transport
is not an authentication failure, and MGMT_EV_AUTH_FAILED would make
bluetoothd disconnect the device.
Tested on the affected host (kernel 7.0.12, MediaTek MT7922, Bose QC
Ultra) with the patched module built out of tree: 7 days and 49
reconnects without a drop, against 2 drops in the 3 days before the
patch. Every disconnect in that week had a userspace or remote reason.
Fixes: b5ae344d4c ("Bluetooth: Add full SMP BR/EDR support")
Assisted-by: LLM
Signed-off-by: Christiano Amora <christiano.amora@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_sock_cleanup_listen() closes unaccepted child sockets through
rfcomm_sock_close(), which takes the child socket lock before
rfcomm_dlc_close() acquires rfcomm_mutex. The RFCOMM worker takes these
locks in reverse order while handling connections and DLC state changes,
so lockdep reports a possible deadlock.
Close dequeued children without taking their socket lock. The accept queue
owns a reference to each child, and bt_accept_dequeue() locks the child
while unlinking it and clearing its parent pointer.
Dropping the child lock makes it important to prevent a concurrent
rfcomm_connect_ind() from enqueueing a new child after cleanup observes an
empty queue. Set a listening socket to BT_CLOSED while its lock is still
held, before dropping the lock and draining the queue. The state check in
rfcomm_connect_ind() then rejects new children once cleanup starts.
Reported-by: syzbot+0cece8fa7d83523f47a3@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=0cece8fa7d83523f47a3
Fixes: b7ce436a5d ("Bluetooth: switch to lock_sock in RFCOMM")
Signed-off-by: Juan Perdomo <jcperdomo100@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_connect_le() swaps the caller's identity address for the peer's
cached RPA when one is known, and stamps the matching
ADDR_LE_DEV_RANDOM on the local dst_type. On the conn-reuse path only
the address is copied into the connection:
if (conn) {
bacpy(&conn->dst, dst);
so conn->dst ends up holding an RPA while conn->dst_type still names the
identity it was resolved from, and hci_le_create_conn_sync() puts that
pair on air unchanged. An RPA declared as a public address is not
something any peer can answer.
Measured on a CYW43438 against a peer advertising an RPA the host holds
the IRK for, connecting to the identity address over a raw L2CAP socket.
The first attempt creates the connection, the second takes the reuse
path:
LE Create Connection 3C:78:95:78:37:C3 type public
LE Create Connection 5B:75:A2:26:D6:18 type public
LE Connection Complete: Unknown Connection Identifier (0x02)
The second address is the peer's RPA. btmon annotates it with an OUI
lookup rather than "(Resolvable)" precisely because the command declares
it public; the same bit pattern annotates as resolvable once the type is
right.
The mistyped pair is also why nothing downstream repairs it.
hci_bdaddr_is_rpa() tests the type before the address, so an RPA carrying
a public type is not recognised as one, and hci_find_irk_by_addr() then
searches for an identity address that does not match it either.
Copy the type along with the address.
The assignment used to be unconditional just below this block and covered
both paths; it moved into hci_conn_add_unset(), which the reuse path does
not go through.
Cc: stable@vger.kernel.org
Fixes: 14b06c3a88 ("Bluetooth: HCI: Always use the identity address when initializing a connection")
Assisted-by: Claude:claude-opus-5
Signed-off-by: Radek Podgorny <radek@podgorny.cz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btintel_pcie_submit_rx() used frbd_index > rxq->count to guard the
FRBD array access, allowing frbd_index == rxq->count to pass through
and index one element past the end of the array. Change the check to
>= rxq->count so every out-of-range index is rejected.
This issue was reported by Claude Mythos.
Fixes: c2b636b3f7 (Bluetooth: btintel_pcie: Add support for PCIe transport)
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In btmtksdio_shutdown(), pm_runtime_get_sync() is called at the
beginning of the function. However, if sending the WMT function
control command fails later, the driver returns early.
It bypasses the corresponding pm_runtime_put_noidle() and
pm_runtime_disable() calls, leaking the PM usage counter and leaving PM
runtime enabled indefinitely.
Fall through to execute the PM runtime cleanup block even if WMT errors.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btmtksdio.c and btmtkuart.c cast a received WMT event straight to
struct btmtk_hci_wmt_evt and read its op/flag fields without checking
the event is long enough to contain them, unlike btmtk.c. The
FUNC_CTRL case then further casts to struct btmtk_hci_wmt_evt_funcc
and reads its 2-byte status field, again without a length check.
Firmware that sends a short or malformed WMT event makes both drivers
read past the end of the received SKB.
Mirror btmtk.c: validate the base WMT header with skb_pull_data()
before touching any of its fields, and when a FUNC_CTRL event turns
out to be the short, header-only form (a plain enable/disable ack
with no status word), decode the result from the header's own flag
byte instead (0 = success, otherwise failure).
Verified setup on MT7920, MT7921, MT7922 and MT7925: no regression.
Fixes: 9aebfd4a22 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Fixes: e0b67035a9 ("Bluetooth: mediatek: update the common setup between MT7622 and other devices")
Assisted-by: Claude:claude-opus-5
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A too-short BTMTK_WMT_FUNC_CTRL event (WMT header only, no trailing
2-byte status word) is always treated as BTMTK_WMT_ON_UNDONE. This
short form is how firmware acks a plain enable/disable request, and
the actual result is carried in the header's own flag byte (0 =
success), not a separate status word. Decode it from there instead of
assuming failure.
Verified setup on MT7920, MT7921, MT7922 and MT7925: no regression.
Fixes: e3ac0d9f1a ("Bluetooth: btmtk: accept too short WMT FUNC_CTRL events")
Assisted-by: Claude:claude-opus-5
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A BIS connection is matched to its parent socket by looking for a
socket in BT_LISTEN state with the same BIG handle:
iso_conn_ready()
if (test_bit(HCI_CONN_BIG_SYNC, &hcon->flags))
parent = iso_get_sock(hdev, &hcon->src, &hcon->dst,
BT_LISTEN, iso_match_big_hcon, hcon);
The socket was only moved to BT_LISTEN after iso_conn_big_sync()
returned, while the LE BIG Create Sync command has already been queued
by then. If the BIG sync is established before the state is updated,
which is easy to hit with an emulated controller as the command may
complete in a few hundred microseconds, no parent is found and the BIS
connections are never notified to the listening socket.
The user space is then left waiting for connections that never arrive,
e.g. bluetoothd never completes a MediaTransport1.Acquire of a
Broadcast Sink transport.
Move the socket to BT_LISTEN before requesting the BIG sync, so the
state is visible by the time the command is queued, and restore the
previous state if the request could not be started. Since the socket is
briefly visible as a listening socket, child sockets may have been
queued in the meantime, so drain the accept queue before restoring the
state: the cleanup paths of BT_CONNECT2/BT_CONNECTED don't do it and the
children would be left with a dangling parent pointer.
Fixes: fbdc4bc472 ("Bluetooth: ISO: Use defer setup to separate PA sync and BIG sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
iso_get_sock() returns the parent socket with a reference held, which is
dropped by sock_put() once the child socket has been set up. The error
path taken when iso_sock_alloc() fails only calls release_sock() and
returns, leaking the reference and thus the parent socket itself.
Drop the reference on that path as well.
Fixes: fa224d0c09 ("Bluetooth: ISO: Reassociate a socket with an active BIS")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_dev_close_sync() clears hdev->local_codecs after releasing hdev->lock.
Codec list additions and both traversals in sco_sock_getsockopt() use that
lock, but the close path does not. A close and BT_CODEC query can therefore
interleave as follows:
hci_dev_close_sync() sco_sock_getsockopt()
hci_dev_lock()
fetch codec entry
hci_codec_list_clear()
kfree(entry)
read entry->id
The reader then accesses an entry which the close path has freed. KASAN
reported:
BUG: KASAN: slab-use-after-free in sco_sock_getsockopt+0xfa0/0xfe0
Read of size 1 at addr ffff8881001c3450
Call Trace:
sco_sock_getsockopt+0xfa0/0xfe0
do_sock_getsockopt+0x537/0x7b0
__sys_getsockopt+0xf2/0x170
Allocated by task 92:
hci_codec_list_add.isra.0+0x2c/0x440
hci_read_codec_capabilities+0x224/0x590
hci_read_supported_codecs+0x2c2/0x640
Freed by task 92:
kfree+0x131/0x3c0
hci_codec_list_clear+0xd8/0x160
hci_dev_close_sync+0x92a/0xfa0
Take hdev->lock around the clear operation at its existing point in the
close path. This makes the clear wait for active readers and prevents a new
traversal until the list is empty without changing teardown ordering.
Fixes: b938790e70 ("Bluetooth: hci_codec: Fix leaking content of local_codecs")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP
is set (for example, for the WCN399x family). A failed hci_dev_open_sync()
following a successful qca_setup() calls hdev->close() but not
hdev->shutdown(), so the port is closed while power->vregs_on is left true.
qca_serdev_remove() then passes its power->vregs_on test and calls
qca_power_off(), which writes to the closed port unconditionally.
Seen on a WCN3988 by unbinding the driver after a controller failure. The
trace below is from a 7.0.0 based kernel, where qca_power_off() was still
named qca_power_shutdown():
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000038
Call trace:
tty_set_termios+0x50/0x238 (P)
ttyport_set_baudrate+0x84/0xc0
serdev_device_set_baudrate+0x24/0x40
qca_power_shutdown+0x158/0x1fc [hci_uart]
qca_serdev_remove+0x54/0x68 [hci_uart]
serdev_drv_remove+0x1c/0x2c
device_remove+0x4c/0x80
device_release_driver_internal+0x1cc/0x224
device_driver_detach+0x18/0x24
unbind_store+0xb4/0xc0
Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place
it closes the port, before writing to it. The regulator disable is left
unconditional so the controller is still powered down.
The dangling serport->tty that turns this into a use-after-free is
addressed in a separate patch.
Fixes: fa9ad876b8 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Signed-off-by: Ibrahim Abdelkader <iabdelka@qti.qualcomm.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Read Local Supported Codecs parsers consume the variable-sized
standard codec array before parsing the vendor codec count. Although the
initial reply-size check includes a vendor count byte in the fixed layout,
it does not guarantee that the byte remains after the standard codec array.
If a controller reply ends immediately after that array, calculating the
vendor codec array size reads vnd_codecs->num beyond the skb data. Use
skb_pull_data() to validate and consume each codec header before using its
count in both command variants.
Fixes: 8961987f3f ("Bluetooth: Enumerate local supported codec and cache details")
Fixes: 9ae664028a ("Bluetooth: Add support for Read Local Supported Codecs V2")
Cc: stable@vger.kernel.org
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Laxman Acharya Padhya <acharyalaxman8848@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
An identity address only reaches a peer that is advertising an RPA if the
controller resolves it on our behalf. Where it cannot, the host has to put
the peer's on-air address on air itself.
hci_connect_le() still swaps the caller's identity address for the peer's
cached RPA before creating the connection, but __hci_conn_add() resolves
the RPA back to the identity address when it stores it, so the identity is
what goes out. Storing the identity is right when the controller
translates it on the way to the radio; without LL Privacy, or with this
peer absent from the resolving list, nothing does.
A peer advertising an RPA cannot answer its identity address, so the
attempt burns a full create-connection timeout. That is not merely a slow
connect: a controller without extended scanning cannot scan while it is
initiating, so every dead attempt also takes the scanner off the air for
the whole timeout.
Measured on a CYW43438, which reports neither LL Privacy nor extended
advertising (LE features 3f 00 00 08 00 00 00 00), against a peer
advertising a resolvable private address the host holds the IRK for, with
the connection requested on the peer's identity address:
before: LE Create Connection to the identity address, public type
1.61s -> 22.07s, then LE Create Connection Cancel
LE Connection Complete: Unknown Connection Identifier (0x02)
after: LE Create Connection to the peer's RPA, random type
LE Connection Complete: Success
Advertising reports reaching the host per second, same window, same five
unrelated devices on the adapter:
before 1s:2 [nothing from 2s through 21s] 22s:5 23s:3
after 0s:11 1s:5 2s:2 3s:5 4s:3 5s:4 ... 21s:2 22s:1 23s:2
One dead connect costs twenty seconds of scanning for every device on the
adapter, not just the one being dialled.
Keep the RPA in conn->dst unless the controller will translate the
identity address: address resolution enabled and the peer's identity
actually programmed into the resolving list. Testing ll_privacy_capable()
alone would not be enough: it reports the feature bit, not whether
resolution is switched on and not whether this peer is in the list.
Resolution is cleared with the other volatile flags on power-off and
switched off again while suspend pauses scanning, and a peer's IRK is only
programmed along the accept list path, so a direct-connect target, a peer
without HCI_CONN_FLAG_ADDRESS_RESOLUTION, and one that did not fit in a
full list are all absent from it.
With the peer programmed, the identity address stays in conn->dst and the
controller translates it: measured on an Intel controller, the host dials
the identity and LE Enhanced Connection Complete reports Resolved Public
with the peer's RPA in the separate peer resolvable private address field.
With the peer absent from the list the same setup dials the RPA itself.
Everything downstream already copes with an RPA in conn->dst: it is what
every outgoing LE connection stored before 14b06c3a88, the connection
complete event names the address that was dialled, and
le_conn_complete_evt() resolves it back to the identity once the link is
up. ISO links keep the unconditional conversion: they are created from an
existing ACL or a periodic sync and never dial this address themselves.
Keeping the RPA is only right while the peer is still using it, which is
why the preceding patch drops the cached RPA as soon as the peer is seen
advertising its identity address. Without that, a peer that turns privacy
off would be dialled on the address it abandoned rather than the one it
is answering on.
Fixes: 14b06c3a88 ("Bluetooth: HCI: Always use the identity address when initializing a connection")
Assisted-by: Claude:claude-opus-5
Assisted-by: Claude:claude-fable-5
Signed-off-by: Radek Podgorny <radek@podgorny.cz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_devcd_handle_pkt_init() arms dump_timeout and coredump producers
queue dump_rx without holding an hdev reference. Unregister leaves both
works live, so disconnecting during an active dump lets them access hdev
after hci_release_dev() frees it.
Shut down coredump processing during unregister. Close the producer gate
under dump_q.lock before disabling both works, then free the active buffer
and queued packets under hci_dev_lock. Serializing the gate with enqueue
prevents controller-specific workers from adding packets after the final
purge.
Fixes: 9695ef876f ("Bluetooth: Add support for hci devcoredump")
Reported-by: syzbot+b170dbf55520ebf5969a@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=b170dbf55520ebf5969a
Reported-by: Aby Sam Ross <abysamross@gmail.com>
Link: https://lore.kernel.org/r/20260322210849.68743-1-abysamross@gmail.com
Suggested-by: Aby Sam Ross <abysamross@gmail.com>
Reported-by: Tristan Madani <tristan@talencesecurity.com>
Link: https://lore.kernel.org/r/20260814231248.3096377-1-tristmd@gmail.com
Reported-by: Xiang Mei <xmei5@asu.edu>
Assisted-by: OpenAI Codex:gpt-5
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btintel_pcie_prepare_tx() copies skb->len bytes into a fixed
BTINTEL_PCIE_BUFFER_SIZE (4096) DMA slot via an unchecked memcpy.
Oversized packets are currently rejected only in
btintel_pcie_send_frame(); any future caller of
btintel_pcie_send_sync() would silently overflow the DMA buffer.
Add the bounds check in btintel_pcie_send_sync() itself, right
before skb_push() and the DMA copy.
Assisted-by: Copilot:claude-sonnet-5 code-review code-generation
Fixes: 6e65a09f92 ("Bluetooth: btintel_pcie: Add *setup* function to download firmware")
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_send_acl(), hci_send_sco() and hci_send_iso() queue hdev->tx_work
unconditionally. They can run from the L2CAP/SCO/ISO socket send path
while hci_dev_close_sync() is draining hdev->workqueue (HCIDEVDOWN
racing with a socket write). Since that queue_work() is not chained
work from the tx_work worker itself, __queue_work() sees the queue
marked __WQ_DRAINING, warns "cannot queue %ps on wq %s", and drops
the work:
WARNING: CPU: 1 PID: 5985 at kernel/workqueue.c:2352 __queue_work
Call Trace:
queue_work_on
l2cap_chan_send
l2cap_sock_sendmsg
...
hci_dev_close_sync() already sets HCI_CMD_DRAIN_WORKQUEUE before
draining, but only hci_cmd_work() and handle_cmd_cnt_and_timer()
check it before queuing. Route the tx_work producers through the
same guard via a shared hci_sched_tx() helper.
Fixes: 525daaea45 ("Bluetooth: hci_sync: Set HCI_CMD_DRAIN_WORKQUEUE during device close")
Reported-by: syzbot+b6919040d9958e2fc1ae@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=b6919040d9958e2fc1ae
Signed-off-by: ThangNN99 <ngocthang2710.1999@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
eir_get_service_data() reads a 16-bit UUID from the service data using
get_unaligned_le16() without first checking that the data is long enough
to hold a UUID16 (2 bytes). If a malformed EIR entry has a service data
field with only 1 byte of payload (field_len=2), eir_get_data() returns
dlen=1. The subsequent get_unaligned_le16() then reads 1 byte past the
field boundary.
Additionally, if the corrupted UUID happens to match, the length
calculation "dlen - 2" underflows to SIZE_MAX since dlen is size_t.
Current callers either pass NULL for the length parameter or bounds-check
the returned length, but future callers may not.
Add a check that dlen >= sizeof(u16) and skip fields that are too short
to contain a valid UUID16.
Fixes: 8f9ae5b3ae ("Bluetooth: eir: Add helpers for managing service data")
Cc: stable@vger.kernel.org
Signed-off-by: Aamir Ahmed <elb12345@hotmail.co.uk>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The NXP IW610 module exposes itself as a composite USB device
(0471:0215) with three interfaces: two real Bluetooth HCI interfaces
(class 0xe0) and one vendor-specific WiFi interface (class 0xff) used
by mwifiex-nxp.
The composite device's whole USB descriptor reports class 0xe0/01/01
(Bluetooth), so btusb_table's generic USB_DEVICE_INFO(0xe0, 0x01, 0x01)
entry matches every interface, not just the two real HCI ones -- btusb
ends up binding the WiFi interface too, and mwifiex-nxp never gets it.
Fix:
1. In btusb_table (the table the USB core actually matches against),
explicitly ignore the WiFi interface via BTUSB_IGNORE, ahead of the
generic entry.
2. In quirks_table, scope the existing BTUSB_MARVELL entry to the BT
interface class instead of matching the whole device by VID/PID
(harmless either way since quirks_table isn't consulted for initial
binding, but keep it correct).
Not upstream anywhere: checked NXP's own i.MX kernel fork
(nxp-imx/linux-imx), no IW610 references in btusb.c on any branch --
their reference designs wire this chip differently (WiFi over SDIO
per their release notes), so they never hit this.
Signed-off-by: Nicolas Thibert <nithibert@gmail.com>
Cc: stable@vger.kernel.org
Assisted-by: LLM (Claude Sonnet 5, Anthropic)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We can hit a division by zero crash in tcp_rcvbuf_grow()
and tcp_rcv_space_adjust():
divide error: 0000 [#1] PREEMPT SMP
RIP: 0010:tcp_rcvbuf_grow+0x187/0x450 net/ipv4/tcp_input.c:939
...
grow = div_u64(((u64)rcvwin << 1) * (newval - oldval), oldval);
The division uses oldval = tp->rcvq_space.space as divisor.
When tp->rcvq_space.space is zero, this leads to a divide-by-zero
exception.
tp->rcvq_space.space is initialized in tcp_init_buffer_space():
tp->rcvq_space.space = min3(tp->rcv_ssthresh, tp->rcv_wnd,
(u32)TCP_INIT_CWND * tp->advmss);
If tcp_rmem[1] is configured to very small values (such as 1),
sk->sk_rcvbuf is initialized to 1. Then tcp_full_space(sk), which
computes (sk->sk_rcvbuf * scaling_ratio) >> 8, truncates to 0.
This sets tp->window_clamp = 0, tp->rcv_ssthresh = 0, and
tp->rcvq_space.space = 0. Later, when data arrives and DRS is invoked,
tcp_rcvbuf_grow() divides by oldval == 0.
Back in 2015, commit b1cb59cf2e ("net: sysctl_net_core: check SNDBUF
and RCVBUF for min length") ensured that net.core.rmem_default and
net.core.rmem_max cannot be set below SOCK_MIN_RCVBUF. Similarly,
SO_RCVBUF setsockopt enforces max_t(int, val * 2, SOCK_MIN_RCVBUF).
However, net.ipv4.tcp_rmem still had .extra1 = SYSCTL_ONE, allowing
arbitrarily small values.
Because SOCK_MIN_RCVBUF depends on sizeof(struct sk_buff) and cacheline
alignment, its value varies across architectures and configuration options.
Using a fixed constant of 4096 ensures a predictable, architecture-
independent lower bound that is safely above SOCK_MIN_RCVBUF everywhere
and matches the documented 4K default.
Fix this by setting tcp_rmem.extra1 to 4096 and updating the documentation.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260912144848.3448026-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cover the new TCA_HHF_HH_FLOWS_LIMIT bound: values above 2*HH_FLOWS_CNT
(4294967295, 65536, 2049) are rejected with the configured limit left
untouched on both the change and the add path, the boundary value 2048 is
accepted (installed at 100 first so the boundary change is load-bearing),
and an add-time hh_limit 500 is preserved instead of being clobbered by
the default.
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Tested-by: hybris <hybris@mojatatu.ai>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/QDISC-B855.v1.20260911153152@mojatatu.com.2
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
hhf_change() stores TCA_HHF_HH_FLOWS_LIMIT with no upper bound. A huge
hh_flows_limit lets each new heavy-hitter flow pass the
hh_flows_current_cnt check in alloc_new_hh() and forces a fixed-size
kzalloc(GFP_ATOMIC) per flow under spoofed traffic, for unbounded memory
growth.
Bound the attribute with NLA_POLICY_MAX() at 2*HH_FLOWS_CNT (the
hhf_init() default) and report the rejected value via extack. The
deprecated nested parse is kept: legacy tc does not set NLA_F_NESTED on
TCA_OPTIONS. Configs relying on hh_limit above the default were relying
on unbounded, unsafe behaviour and are not supported going forward.
hhf_init() also ran hhf_change() before setting the default
hh_flows_limit, so a user-supplied hh_limit at add time was clobbered
back to 2048. Set the default before hhf_change() so the configured
value sticks.
This is a follow-up to commit eb56a495f5 ("net/sched: hhf: clamp
quantum in change and init paths"), which bounded the quantum of the
same qdisc; the hh_flows_limit bound is the remaining unbounded knob of
that series' scope.
Conditions to recreate the bug: CAP_NET_ADMIN in a user namespace;
tc qdisc change dev X root hhf hh_limit 4294967295 succeeds and the
value is echoed by tc qdisc show, unbounding heavy-hitter flow
allocations; also tc qdisc add dev X root hhf hh_limit 500 stores 2048
instead of 500.
Fixes: 10239edf86 ("net-qdisc-hhf: Heavy-Hitter Filter (HHF) qdisc")
Cc: stable@vger.kernel.org
Reported-by: Sashiko (gemini) <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260822195509.112717-1-jhs@mojatatu.com
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Tested-by: hybris <hybris@mojatatu.ai>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/QDISC-B855.v1.20260911153152@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is a follow-up of one of sashiko's pre-existing bug reports.
br_mst_set_state() calls switchdev_port_attr_set() for nonzero MSTIs
while holding rcu_read_lock() which invokes the blocking switchdev
notifier chain and may sleep. Nonzero MSTI changes come from netlink
with rtnl held. Move the switchdev call before entering the rcu section and
assert that rtnl is held.
The call cannot be deferred because netlink needs its error and extack.
Also DSA reads the old bridge MST state during the callback and checks it.
A deferred callback will be late and will see the updated state.
Fixes: 3a7c1661ae ("net: bridge: mst: fix vlan use-after-free")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260911105021.1385934-1-razor@blackwall.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
skfp_ctl_set_mac_address() calls ResetAdapter() unconditionally, without
checking netif_running(). ResetAdapter() first calls card_stop(), which
sets smc->hw.hw_state to STOPPED, and then mac_drv_clear_tx_queue(),
which walks the two transmit queues:
for (i = QUEUE_S; i <= QUEUE_A0; i++) {
queue = smc->hw.fp.tx[i] ;
...
t = queue->tx_curr_get ;
smc->hw.fp.tx[] is only populated by init_tx(), which is reached from
skfp_open() through init_smt() -> init_fddi_driver() -> init_fplus() ->
init_mac() -> init_tx(). The private area is allocated and zeroed by
alloc_fddidev(), so on an interface that has never been brought up both
queue pointers are still NULL. The hw_state test at the top of
mac_drv_clear_tx_queue() does not catch this, because card_stop() has
just set STOPPED; the function proceeds into the loop and dereferences
NULL. ResetAdapter() does call init_smt() itself, but only after the
queues have been cleared.
Setting the MAC address on a down interface therefore oopses:
ip link set dev fddi0 address 02:00:00:00:00:01
BUG: KASAN: null-ptr-deref in mac_drv_clear_tx_queue+0x68/0x2c0 [skfp]
Read of size 8 at addr 0000000000000010 by task ip/302
Call Trace:
<TASK>
mac_drv_clear_tx_queue+0x68/0x2c0 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
ResetAdapter+0x29/0x100 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
skfp_ctl_set_mac_address+0x57/0x80 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
netif_set_mac_address+0x1e4/0x2c0
do_setlink+0x684/0x2680
</TASK>
Address 0x10 is the offset of tx_curr_get, the third pointer in
struct s_smt_tx_queue, on 64-bit. mac_drv_clear_rx_queue(), which
ResetAdapter() calls immediately afterwards, dereferences
smc->hw.fp.rx[QUEUE_R1] in the same way behind the same ineffective
hw_state test; the transmit queue merely crashes first. Both are
covered by the guard below.
Skip the adapter reset when the interface is down. dev_addr_set() is
left unconditional, so the new address is still recorded in
dev->dev_addr. Nothing is lost by not resetting the adapter here:
skfp_open() deliberately re-reads the factory address on every open,
read_address(smc, NULL);
eth_hw_addr_set(dev, smc->hw.fddi_canon_addr.a);
and the comment above it states this is done to discard exactly such an
address override across a close/open cycle. An address set while the
interface is down could not have survived the following open even
before this change, so the guard removes no working behaviour. Guarding
the hardware side of ndo_set_mac_address() with netif_running() is
established practice; skge_set_mac_address() has done so since commit
2eb3e621c4 ("skge: set mac address bonding fix").
Guarding the reset as a whole, rather than NULL-checking the queues, is
also what the rest of the driver expects. After a previous open/close
the queue pointers are stale but non-NULL, so there is no crash, yet
ResetAdapter() goes on to call smt_online() and STI_FBI() ("Enable
Board Interrupts") while skfp_close() has already called free_irq() -
the adapter would be brought back online with no handler installed. The
only other ResetAdapter() caller is skfp_interrupt(), which by
construction runs only while the device is open.
Found by automated driver testing against an emulated SysKonnect FDDI
adapter under a KASAN-enabled 7.0.0 kernel. Triggering it requires
CAP_NET_ADMIN.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Assisted-by: LLM KASAN
Signed-off-by: Hohyun Sim <tlaghgus0425@korea.ac.kr>
Link: https://patch.msgid.link/20260910063743.110747-1-tlaghgus0425@korea.ac.kr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the forward output route cannot be used in icmp_route_lookup(),
it enters the "reverse path" and calls ip_route_input() on fl4_dec.daddr,
the original packet's source address.
ip_route_input() only returns an error for truly invalid packets. For
unreachable addresses it will succeed and return an input route whose
dst.output is set to ip_rt_bug(). The existing check only rejects
RTN_LOCAL routes, so the RTN_UNREACHABLE route types can still be returned
and later used for output, syzkaller triggering a WARN_ON_ONCE()
in ip_rt_bug() as bellow:
------------[ cut here ]------------
WARNING: net/ipv4/route.c:1273 at ip_rt_bug+0x14/0x20
RIP: 0010:ip_rt_bug+0x14/0x20
Call Trace:
ip_push_pending_frames+0xfa/0x100
__icmp_send+0x905/0xf10
ip_options_compile+0xc0/0xd0
ip_rcv_finish_core+0x321/0xae0
ip_rcv+0x1de/0x260
__netif_receive_skb_one_core+0x11a/0x130
netif_receive_skb+0x7b/0x260
tun_get_user+0x11bf/0x1c10
------------[ cut here ]------------
Reject input route that is RTN_UNREACHABLE to fix it. The net warning
is only printed for RTN_LOCAL, as RTN_UNREACHABLE is not the result of
a race condition.
Fixes: 8b7817f3a9 ("[IPSEC]: Add ICMP host relookup support")
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Link: https://patch.msgid.link/20260910140042.1880242-1-dongchenchen2@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bcmgenet_hfb_init() runs INIT_LIST_HEAD() on priv->rxnfc_list, which drops
every rule off the list, and bcmgenet_open() calls it on each ifup. Every
rule the user configured is silently lost:
# ethtool -N eth0 flow-type ether dst $MAC action 0
Added rule with ID 0
# ethtool -n eth0 | grep -c Filter:
1
# ip link set eth0 down && ip link set eth0 up
# ethtool -n eth0 | grep -c Filter:
0
Initialise the lists once at probe and restore the rules on open, as
bcmgenet_resume() already does.
Fixes: 3e37095228 ("net: bcmgenet: add support for ethtool rxnfc flows")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260913190052.939955-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mxl862xx_setup() arms the stats poll before mxl862xx_setup_mdio(), and
nothing stops it until dsa_register_switch() has returned an error to
mxl862xx_probe(). DSA frees the dsa_port list before it returns, so a
poll that fires once .setup or a later step of dsa_tree_setup() has
failed walks freed ports. On shutdown the user ports stay registered,
and the WORK_STOPPED flag test in mxl862xx_get_stats64() is not atomic
with the cancel in mxl862xx_shutdown(), so a re-arm that read the flag
before it was set queues the poll after cancel_delayed_work_sync() has
returned.
Arm the poll once .setup has succeeded and stop it from a .teardown op,
which DSA calls on unregister and after a failed registration, in both
cases before it frees the ports. Use disable_delayed_work_sync() there
and in shutdown(): it drains a running poll as the cancel did and turns
every later attempt to queue the work into a no-op, so the re-arm
cannot bring the poll back. remove() and the probe error path only set
WORK_STOPPED, which crc_err_work tests before it walks the ports.
Fixes: a21d33a526 ("net: dsa: mxl862xx: implement .get_stats64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/1eb6f7fc1789b67e4b11e3f4d5ff080d0b6f7cbb.1789045590.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
