[ Upstream commit bd5431b2f9 ]
Although the schematics of Pine A64-LTS and SoPine Baseboard shows both
the RX and TX internal delay are enabled, they're using the same broken
RTL8211E chip batch with Pine A64+, so they should use TXID instead, not
ID.
In addition, by checking the real components soldered on both a SoPine
Baseboard and a Pine A64-LTS, RX delay is not enabled (GR69 soldered and
GR70 NC) despite the schematics says it's enabled. It's a common
situation for Pine64 boards that the NC information on schematics is not
the same with the board.
So the RGMII delay mode should be TXID on these boards.
Fixes: c2b111e59a ("arm64: dts: allwinner: A64 Sopine: phy-mode rgmii-id")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210609083843.463750-1-icenowy@aosc.io
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0d09b123 ]
On probe error the driver should free the memory allocated for private
structure. Fix this by using resource-managed allocation.
Fixes: a20cbdeffc ("powerpc/fsl: Add support for Integrated Flash Controller")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210527154322.81253-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b132ab67f ]
On probe error the driver should unmap the IO memory. Smatch reports:
drivers/memory/fsl_ifc.c:298 fsl_ifc_ctrl_probe() warn: 'fsl_ifc_ctrl_dev->gregs' not released on lines: 298.
Fixes: a20cbdeffc ("powerpc/fsl: Add support for Integrated Flash Controller")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210527154322.81253-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c6d0b55b4 ]
Rename the external refclk inputs to the SERDES from
dummy_cmn_refclk/dummy_cmn_refclk1 to cmn_refclk/cmn_refclk1
respectively. Also move the external refclk DT nodes outside the
cbass_main DT node. Since in j721e common processor board, only the
cmn_refclk1 is connected to 100MHz clock, fix the clock frequency.
Fixes: afd094ebe6 ("arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-2-kishon@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1771a33b34 ]
"make dtbs_check":
arm64/boot/dts/renesas/r8a779a0-falcon.dt.yaml: interrupt-controller@f1000000: 'power-domains' does not match any of the regexes: '^(msi-controller|gic-its|interrupt-controller)@[0-9a-f]+$', '^gic-its@', '^interrupt-controller@[0-9a-f]+$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml
Remove the "power-domains" property, as the GIC on R-Car V3U is
always-on, and not part of a clock domain.
Fixes: 834c310f54 ("arm64: dts: renesas: Add Renesas R8A779A0 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/a9ae5cbc7c586bf2c6b18ddc665ad7051bd1d206.1622560236.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fb26fb83f ]
Abort instead of returning a new reset control for a reset controller
device that is going to have its module unloaded.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 61fc413176 ("reset: Add reset controller API")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210607082615.15160-1-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5aede3e6d ]
1. Reorder interrupts
2. Fix typo: s/spi_lr_overhead/spi_lr_overread/
3. Rename node: s/spi-nor@0/flash@0/
This fixes:
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dt.yaml: spi@18029200: interrupt-names: 'oneOf' conditional failed, one must be fixed:
['spi_lr_fullness_reached', 'spi_lr_session_aborted', 'spi_lr_impatient', 'spi_lr_session_done', 'spi_lr_overhead', 'mspi_done', 'mspi_halted'] is too long
Additional items are not allowed ('spi_lr_session_aborted', 'spi_lr_impatient', 'spi_lr_session_done', 'spi_lr_overhead', 'mspi_done', 'mspi_halted' were unexpected)
'mspi_done' was expected
'spi_l1_intr' was expected
'mspi_halted' was expected
'spi_lr_fullness_reached' was expected
'spi_lr_session_aborted' was expected
'spi_lr_impatient' was expected
'spi_lr_session_done' was expected
'spi_lr_overread' was expected
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dt.yaml: spi-nor@0: $nodename:0: 'spi-nor@0' does not match '^flash(@.*)?$'
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92e669017f ]
The SCL gpio pin used by I2C bus for recovery needs to be configured as
open drain, so fix the binding example accordingly.
In relation with fix c5a2838025 ("ARM: dts: at91: Configure I2C SCL
gpio as open drain").
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 19e5cef058 ("dt-bindings: i2c: at91: document optional bus recovery properties")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cb7af474e ]
During an async commands execution the Rx buffer length is at first set
to max_msg_sz when the synchronous part of the command is first sent.
However once the synchronous part completes the transport layer waits
for the delayed response which will be processed using the same xfer
descriptor initially allocated. Since synchronous response received at
the end of the xfer will shrink the Rx buffer length to the effective
payload response length, it needs to be reset again.
Raise the Rx buffer length again to max_msg_sz before fetching the
delayed response to ensure full response is read correctly from the
shared memory.
Link: https://lore.kernel.org/r/20210601102421.26581-2-cristian.marussi@arm.com
Fixes: 58ecdf03db ("firmware: arm_scmi: Add support for asynchronous commands and delayed response")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
[sudeep.holla: moved reset to scmi_handle_response as it could race with
do_xfer_with_response]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fea67710e ]
When call irq_get_irq_data() to get the IRQ's irq_data failed, an
appropriate error code -ENOENT should be returned. However, we directly
return 'err', which records the IRQ number instead of the error code.
Fixes: 139251fc22 ("firmware: tegra: add bpmp driver for Tegra210")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f551b5ce5 ]
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be wasting power
powering hpd when we don't use it on trogdor boards. We didn't notice
this before because the kernel driver blindly disables hpd, but that
won't be true for much longer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324025534.1837405-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cebcf9932 ]
The Microchip LAN8710Ai PHY requires XTAL1/CLKIN external clock to be
enabled when the nRST is toggled according to datasheet Microchip
LAN8710A/LAN8710Ai DS00002164B page 35 section 3.8.5.1 Hardware Reset:
"
A Hardware reset is asserted by driving the nRST input pin low. When
driven, nRST should be held low for the minimum time detailed in
Section 5.5.3, "Power-On nRST & Configuration Strap Timing," on page
59 to ensure a proper transceiver reset. During a Hardware reset, an
external clock must be supplied to the XTAL1/CLKIN signal.
"
This is accidentally fulfilled in the current setup, where ETHCK_K is used
to supply both PHY XTAL1/CLKIN and is also fed back through eth_clk_fb to
supply ETHRX clock of the DWMAC. Hence, the DWMAC enables ETHRX clock,
that has ETHCK_K as parent, so ETHCK_K clock are also enabled, and then
the PHY reset toggles.
However, this is not always the case, e.g. in case the PHY XTAL1/CLKIN
clock are supplied by some other clock source than ETHCK_K or in case
ETHRX clock are not supplied by ETHCK_K. In the later case, ETHCK_K would
be kept disabled, while ETHRX clock would be enabled, so the PHY would
not be receiving XTAL1/CLKIN clock and the reset would fail.
Improve the DT by adding the PHY clock phandle into the PHY node, which
then also requires moving the PHY reset GPIO specifier in the same place
and that then also requires correct PHY reset GPIO timing, so add that
too.
A brief note regarding the timing, the datasheet says the reset should
stay asserted for at least 100uS and software should wait at least 200nS
after deassertion. Set both delays to 500uS which should be plenty.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 516728273d ]
On the production DHCOM STM32MP15xx SoM, the PHY IRQ line is connected
to the PI11 pin. Describe it in the DT as well, so the PHY IRQ can be
used e.g. to detect cable insertion and removal.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 659b38203f ]
Correct the voltages in the "Power Optimized" (<= 1.5 GHz) Cortex-A57
operating point table entries for the R-Car M3-W and M3-W+ SoCs from
0.82V to 0.83V, as per the R-Car Gen3 EC Manual Errata for Revision
0.53.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b9e9db907514790574429b83d070c823b36085ef.1619699909.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44b615ac9f ]
Tag the highest "Power Optimized" (1.5 GHz) Cortex-A57 operating point
table entries for the RZ/G2M, R-Car M3-W and M3-W+ SoCs with the
"opp-suspend" property. This makes sure the system will enter suspend
in the same performance state as it will be resumed by the firmware
later, avoiding state inconsistencies after resume.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: 800037e815 ("arm64: dts: renesas: r8a774a1: Add operating points")
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/45a061c3b0463aac7d10664f47c4afdd999da50d.1619699721.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab8c23096 ]
"make dtbs_check" complains:
arch/arm/boot/dts/r8a7779-marzen.dt.yaml: display@fff80000: clock-names:0: 'du.0' was expected
Change the first clock name to match the DT bindings.
This has no effect on actual operation, as the Display Unit driver in
Linux does not use the first clock name on R-Car H1, but just grabs the
first clock.
Fixes: 665d79aa47 ("ARM: shmobile: marzen: Add DU external pixel clock to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/9d5e1b371121883b3b3e10a3df43802a29c6a9da.1619699965.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54b909436e ]
The scnprintf() function silently truncates the printf() and returns
the number bytes that it was able to copy (not counting the NUL
terminator). Thus, the highest value it can return here is
"NAME_SIZE - 1" and the overflow check is dead code. Fix this by
using the snprintf() function which returns the number of bytes that
would have been copied if there was enough space and changing the
condition from "> NAME_SIZE" to ">= NAME_SIZE".
Fixes: 92589c986b ("rtc-proc: permit the /proc/driver/rtc device to use other devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/YJov/pcGmhLi2pEl@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b19d3479f2 ]
Commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the Orange Pi Plus board this is "rgmii", which is the
wrong setting.
Following the example of a900cac375 ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Reported-by: "B.R. Oake" <broake@mailfence.com>
Reported-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Link: https://bugs.debian.org/988574
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210524122111.416885-1-carnil@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76e5624f3f ]
When no child nodes are matched, an appropriate error code -ENODEV should
be returned. However, we currently do not explicitly assign this error
code to 'err'. As a result, 0 was incorrectly returned.
Fixes: fee10bd226 ("memory: pl353: Add driver for arm pl353 static memory controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210515040004.6983-1-thunder.leizhen@huawei.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e207457f90 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 77750bc089 ("reset: Add Broadcom STB SW_INIT reset controller driver")
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620789283-15048-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907c5bbb51 ]
Early exits from for_each_available_child_of_node() should decrement the
node reference counter. Reported by Coccinelle:
drivers/memory/atmel-ebi.c:593:1-33: WARNING:
Function "for_each_available_child_of_node" should have of_node_put() before return around line 604.
Fixes: 6a4ec4cd08 ("memory: add Atmel EBI (External Bus Interface) driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210423101815.119341-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f9dc6a357 ]
Early exits from for_each_available_child_of_node() should decrement the
node reference counter. Reported by Coccinelle:
drivers/memory/stm32-fmc2-ebi.c:1046:1-33: WARNING:
Function "for_each_available_child_of_node" should have of_node_put() before return around line 1051.
Fixes: 66b8173a19 ("memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Christophe Kerello <christophe.kerello@foss.st.com>
Link: https://lore.kernel.org/r/20210423101815.119341-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd2f171796 ]
There is no "max_brightness" property as pointed out by dtschema:
arch/arm/boot/dts/exynos5422-odroidxu4.dt.yaml: led-controller: led-1: 'max-brightness' is a required property
Fixes: 6658356014 ("ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-5-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7e59c84cf ]
There is no "max_brightness" property as pointed out by dtschema:
arch/arm/boot/dts/exynos5422-odroidhc1.dt.yaml: led-controller: led-1: 'max-brightness' is a required property
Fixes: 1ac49427b5 ("ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-4-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75121e1dc9 ]
There is no "max_brightness" property. This brings the intentional
brightness reduce of green LED and dtschema checks as well:
arch/arm/boot/dts/exynos5410-odroidxu.dt.yaml: led-controller-1: led-1: 'max-brightness' is a required property
Fixes: 719f39fec5 ("ARM: dts: exynos5422-odroidxu3: Hook up PWM and use it for LEDs")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d551bf20 ]
Early exits from for_each_compatible_node() should decrement the
node reference counter. Reported by Coccinelle:
arch/arm/mach-exynos/exynos.c:52:1-25: WARNING:
Function "for_each_compatible_node" should have of_node_put() before break around line 58.
Fixes: b3205dea8f ("ARM: EXYNOS: Map SYSRAM through generic DT bindings")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210425174945.164612-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 466ba3c8ff ]
The driver defined of_device_id table but did not use it with
of_match_table. This prevents usual matching via devicetree and causes
a W=1 warning:
drivers/reset/reset-a10sr.c:111:34: warning:
‘a10sr_reset_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 6270068202 ("reset: Add Altera Arria10 SR Reset Controller")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210507112803.20012-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab9d6219f ]
The Intel Gateway reset controller is only present on Intel Gateway
platforms. Hence add a dependency on X86, to prevent asking the user
about this driver when configuring a kernel without Intel Gateway
support.
Fixes: c9aef213e3 ("reset: intel: Add system reset controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42f6a76fbe ]
The Broadcom STB RESCAL reset controller is only present on Broadcom
BCM7216 platforms. Hence add a dependency on ARCH_BRCMSTB, to prevent
asking the user about this driver when configuring a kernel without
BCM7216 support.
Also, merely enabling CONFIG_COMPILE_TEST should not enable additional
code, and thus should not enable this driver by default.
Fixes: 4cf176e523 ("reset: Add Broadcom STB RESCAL reset controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3bb3d27c ]
Two ethernet node was added by
commit 95220046a6 ("ARM: dts: Add ethernet to a bunch of platforms")
and commit d6d0cef55e ("ARM: dts: Add the FOTG210 USB host to Gemini boards")
This patch removes the duplicate one.
Fixes: d6d0cef55e ("ARM: dts: Add the FOTG210 USB host to Gemini boards")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 681ba73c72 ]
ld.lld warns that the '.modinfo' section is not currently handled:
ld.lld: warning: kernel/built-in.a(workqueue.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(printk/printk.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(irq/spurious.o):(.modinfo) is being placed in '.modinfo'
ld.lld: warning: kernel/built-in.a(rcu/update.o):(.modinfo) is being placed in '.modinfo'
The '.modinfo' section was added in commit 898490c010 ("moduleparam:
Save information about built-in modules in separate file") to the DISCARDS
macro but Hexagon has never used that macro. The unification of DISCARDS
happened in commit 023bf6f1b8 ("linker script: unify usage of discard
definition") in 2009, prior to Hexagon being added in 2011.
Switch Hexagon over to the DISCARDS macro so that anything that is
expected to be discarded gets discarded.
Link: https://lkml.kernel.org/r/20210521011239.1332345-3-nathan@kernel.org
Fixes: e95bf452a9 ("Hexagon: Add configuration and makefiles for the Hexagon architecture.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fef087d0d ]
Patch series "hexagon: Fix build error with CONFIG_STACKDEPOT and select CONFIG_ARCH_WANT_LD_ORPHAN_WARN".
This series fixes an error with ARCH=hexagon that was pointed out by the
patch "mm/slub: use stackdepot to save stack trace in objects".
The first patch fixes that error by handling the '.irqentry.text' and
'.softirqentry.text' sections.
The second patch switches Hexagon over to the common DISCARDS macro, which
should have been done when Hexagon was merged into the tree to match
commit 023bf6f1b8 ("linker script: unify usage of discard definition").
The third patch selects CONFIG_ARCH_WANT_LD_ORPHAN_WARN so that something
like this does not happen again.
This patch (of 3):
Patch "mm/slub: use stackdepot to save stack trace in objects" in -mm
selects CONFIG_STACKDEPOT when CONFIG_STACKTRACE_SUPPORT is selected and
CONFIG_STACKDEPOT requires IRQENTRY_TEXT and SOFTIRQENTRY_TEXT to be
handled after commit 505a0ef15f ("kasan: stackdepot: move
filter_irq_stacks() to stackdepot.c") due to the use of the
__{,soft}irqentry_text_{start,end} section symbols. If those sections are
not handled, the build is broken.
$ make ARCH=hexagon CROSS_COMPILE=hexagon-linux- LLVM=1 LLVM_IAS=1 defconfig all
...
ld.lld: error: undefined symbol: __irqentry_text_start
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __irqentry_text_end
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __softirqentry_text_start
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
ld.lld: error: undefined symbol: __softirqentry_text_end
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
>>> referenced by stackdepot.c
>>> stackdepot.o:(filter_irq_stacks) in archive lib/built-in.a
...
Add these sections to the Hexagon linker script so the build continues to
work. ld.lld's orphan section warning would have caught this prior to the
-mm commit mentioned above:
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
ld.lld: warning: kernel/built-in.a(softirq.o):(.softirqentry.text) is being placed in '.softirqentry.text'
Link: https://lkml.kernel.org/r/20210521011239.1332345-1-nathan@kernel.org
Link: https://lkml.kernel.org/r/20210521011239.1332345-2-nathan@kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1381
Fixes: 505a0ef15f ("kasan: stackdepot: move filter_irq_stacks() to stackdepot.c")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f46f84931a ]
After we grab the lock in nfs4_pnfs_ds_connect(), there is no check for
whether or not ds->ds_clp has already been initialised, so we can end up
adding the same transports multiple times.
Fixes: fc821d5920 ("pnfs/NFSv4.1: Add multipath capabilities to pNFS flexfiles servers over NFSv3")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b77f97a7e ]
If the layout gets invalidated, we should wait for any outstanding
layoutget requests for that layout to complete, and we should resend
them only after re-establishing the layout stateid.
Fixes: d29b468da4 ("pNFS/NFSv4: Improve rejection of out-of-order layouts")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa95edf309 ]
If we have multiple outstanding layoutget requests, the current code to
update the layout barrier assumes that the outstanding layout stateids
are updated in order. That's not necessarily the case.
Instead of using the value of lo->plh_outstanding as a guesstimate for
the window of values we need to accept, just wait to update the window
until we're processing the last one. The intention here is just to
ensure that we don't process 2^31 seqid updates without also updating
the barrier.
Fixes: 1bcf34fdac ("pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aadf2e16 ]
After device reset, the virtqueues are not ready so clear the ready
field.
Failing to do so can result in virtio_vdpa failing to load if the device
was previously used by vhost_vdpa and the old values are ready.
virtio_vdpa expects to find VQs in "not ready" state.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210606053128.170399-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31028cbed2 ]
When 'SB_HW_16' check fails, the error code -ENODEV instead of 0 should be
returned, which is the same as that returned when 'WSS_HW_CMI8330' check
fails.
Fixes: 43bcd973d6 ("[ALSA] Add snd_card_set_generic_dev() call to ISA drivers")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210707074051.2663-1-thunder.leizhen@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 474bc33469 ]
When flushing out the unstable file writes as part of a COMMIT call, try
to perform most of of the data writes and waits outside the semaphore.
This means that if the client is sending the COMMIT as part of a memory
reclaim operation, then it can continue performing I/O, with contention
for the lock occurring only once the data sync is finished.
Fixes: 5011af4c69 ("nfsd: Fix stable writes")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0755d3be2d ]
The sk_user_data pointer is supposed to be modified only while
holding the write_lock "sk_callback_lock", otherwise
we could race with other threads and crash the kernel.
we can't take the write_lock in nvmet_tcp_state_change()
because it would cause a deadlock, but the release_work queue
will set the pointer to NULL later so we can simply remove
the assignment.
Fixes: b5332a9f3f ("nvmet-tcp: fix incorrect locking in state_change sk callback")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a2f966d0f ]
It's unsafe to operate a vq from multiple threads.
Unfortunately this is exactly what we do when invoking
clean tx poll from rx napi.
Same happens with napi-tx even without the
opportunistic cleaning from the receive interrupt: that races
with processing the vq in start_xmit.
As a fix move everything that deals with the vq to under tx lock.
Fixes: b92f1e6751 ("virtio-net: transmit napi")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71ab6a7cfb ]
umem size is a 32 bit unsigned value so assigning it to an int could
cause false failures. Set the calculated value inside the function and
modify function name to reflect the fact it updates the size.
This bug was found during code review but never had real impact to this
date.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210530090349.8360-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3011776af ]
Fix copy paste bug assigning umem1 size to umem2 and umem3. The issue
was discovered when trying to use a 1:1 MR that covers the entire
address space where firmware complained that provided sizes are not
large enough. 1:1 MRs are required to support virtio_vdpa.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210530090317.8284-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f67092eff2 ]
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bc6ea31cb ]
The .remove() callback disables clocks that were not enabled in
.probe(). So just probing and then unbinding the driver results in a clk
enable imbalance.
So just drop the call to disable the clocks. (Which BTW was also in the
wrong order because the call makes the PWM unfunctional and so should
have come only after pwmchip_remove()).
Fixes: 9f4c8f9607 ("pwm: imx: Add ipg clock operation")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 655832d12f ]
The legacy PCI interrupt lines need to be enabled using PCIE_APP_IRNEN bits
13 (INTA), 14 (INTB), 15 (INTC) and 16 (INTD). The old code however was
taking (for example) "13" as raw value instead of taking BIT(13). Define
the legacy PCI interrupt bits using the BIT() macro and then use these in
PCIE_APP_IRN_INT.
Link: https://lore.kernel.org/r/20210106135540.48420-1-martin.blumenstingl@googlemail.com
Fixes: ed22aaaede ("PCI: dwc: intel: PCIe RC controller driver")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rahul Tanwar <rtanwar@maxlinear.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07d6688b22 ]
If the count argument is larger than the xstate size, this will happily
copy beyond the end of xstate.
Fixes: 91c3dba7db ("x86/fpu/xstate: Fix PTRACE frames for XSAVES")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210623121452.120741557@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9625895011 ]
The gap handling in copy_xstate_to_kernel() is wrong when XSAVES is in
use.
Using init_fpstate for copying the init state of features which are
not set in the xstate header is only correct for the legacy area, but
not for the extended features area because when XSAVES is in use then
init_fpstate is in compacted form which means the xstate offsets which
are used to copy from init_fpstate are not valid.
Fortunately, this is not a real problem today because all extended
features in use have an all-zeros init state, but it is wrong
nevertheless and with a potentially dynamically sized init_fpstate this
would result in an access outside of the init_fpstate.
Fix this by keeping track of the last copied state in the target buffer and
explicitly zero it when there is a feature or alignment gap.
Use the compacted offset when accessing the extended feature space in
init_fpstate.
As this is not a functional issue on older kernels this is intentionally
not tagged for stable.
Fixes: b8be15d588 ("x86/fpu/xstate: Re-enable XSAVES")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210623121451.294282032@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
