The iwlmld driver is able to handle TTLM changes as long as all TIDs
have the same TID to Link Mapping. Add the corresponding code so that
mac80211 will accept and trigger the TTLM change.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.3b0a4fd2c12b.I1fab7840f1cc222bd1e8cb58ac1a4177474fcd56@changeid
Temporarily block EMLSR when scanning on a P2P Device interface,
as this is an indication that P2P activity is about to start, e.g.,
P2P client connection to a P2P GO.
Since a P2P scan while a station interface connection is active might
be long, increase the EMLSR blocking timeout to 10 seconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.85fb79d537fe.I27523f8d3f00f2b66f5f555f098e323be29465ea@changeid
For the iwlmld driver the RX command is using struct iwl_rx_mpdu_desc
and not the much older struct iwl_rx_mpdu_res_start. Adjust the value of
rx_mpdu_cmd_hdr_size accordingly so that the trace data is correct.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.688d95d99ff3.Id3055ca6c19cf8c821cbbd80c09ca2a21d9acec7@changeid
Since secs_to_jiffies()(commit:b35108a51cf7) has been introduced, we can
use it to avoid scaling the time to msec.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Link: https://patch.msgid.link/20250612022501.3492345-1-liyuesong@vivo.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Doing a scan right after link activation can be less reliable
than at other times, as the firmware is still busy trying to
catch beacons from the just activated link, etc. In case a new
MLO scan request comes in, defer it for a few seconds after a
link activation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.09548e958a9e.I24dbfd425da260f3ae6fa5a48fe25bd4ab6fcf99@changeid
The (applicable) firmware versions will send an error interrupt as
part of the resume process, so there's no need now to check for it
explicitly. Simplify the code. This also fixes an issue where any
dump taken during the resume isn't able to do the reset handshake
as part of the dump (since interrupts are disabled) and then there
isn't all the correct data and we get more errors later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9e778f1bae0c.I96483b5236ab23141b45079464c73f93e0164e65@changeid
Add a debugfs file to be able to control how long, at most,
the device will sleep before waking up the host. This will
be useful to test certain "assert during suspend" scenarios
for the previous change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9f2a39cae1e1.Ie0003f21286fea50b507d0debe06332b030cd4cb@changeid
The D3 handshake can be interrupted by an error, especially
on resume where we no longer want to check explicitly for
errors. Expand the sx_complete to sx_state and handle any
errors occurring during the handshake.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.157dca92c573.I6dd3b9d2f435c2c363224aa84e373931e56a545f@changeid
At load time, the firmware may request a TOP reset via
bit 6 in the IPC status register. Handle that and set
TOP reset in that case. Since the init will be retried,
there's no need to do anything else.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609211928.0875d5f7e066.I62f14008d89416bc4a3a1056e06762561a7fac57@changeid
The TOP reset requires code to handle the interrupt, which had
been in my patch at some point, but clearly got lost. As the
test had been running on the wrong hardware and failing due to
that, we missed this. Add the missing code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609211928.3f84eb03cc00.If138ceeb8bb178b3931d96b537f746346227e681@changeid
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Use the `DEFINE_RAW_FLEX()` helper for on-stack definitions of
a flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warnings:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:124:52: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2067:51: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2162:43: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2225:43: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/Z_FxXjiMvG5u73fi@kspp
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Core
----
- Implement the Device Memory TCP transmit path, allowing zero-copy
data transmission on top of TCP from e.g. GPU memory to the wire.
- Move all the IPv6 routing tables management outside the RTNL scope,
under its own lock and RCU. The route control path is now 3x times
faster.
- Convert queue related netlink ops to instance lock, reducing
again the scope of the RTNL lock. This improves the control plane
scalability.
- Refactor the software crc32c implementation, removing unneeded
abstraction layers and improving significantly the related
micro-benchmarks.
- Optimize the GRO engine for UDP-tunneled traffic, for a 10%
performance improvement in related stream tests.
- Cover more per-CPU storage with local nested BH locking; this is a
prep work to remove the current per-CPU lock in local_bh_disable()
on PREMPT_RT.
- Introduce and use nlmsg_payload helper, combining buffer bounds
verification with accessing payload carried by netlink messages.
Netfilter
---------
- Rewrite the procfs conntrack table implementation, improving
considerably the dump performance. A lot of user-space tools
still use this interface.
- Implement support for wildcard netdevice in netdev basechain
and flowtables.
- Integrate conntrack information into nft trace infrastructure.
- Export set count and backend name to userspace, for better
introspection.
BPF
---
- BPF qdisc support: BPF-qdisc can be implemented with BPF struct_ops
programs and can be controlled in similar way to traditional qdiscs
using the "tc qdisc" command.
- Refactor the UDP socket iterator, addressing long standing issues
WRT duplicate hits or missed sockets.
Protocols
---------
- Improve TCP receive buffer auto-tuning and increase the default
upper bound for the receive buffer; overall this improves the single
flow maximum thoughput on 200Gbs link by over 60%.
- Add AFS GSSAPI security class to AF_RXRPC; it provides transport
security for connections to the AFS fileserver and VL server.
- Improve TCP multipath routing, so that the sources address always
matches the nexthop device.
- Introduce SO_PASSRIGHTS for AF_UNIX, to allow disabling SCM_RIGHTS,
and thus preventing DoS caused by passing around problematic FDs.
- Retire DCCP socket. DCCP only receives updates for bugs, and major
distros disable it by default. Its removal allows for better
organisation of TCP fields to reduce the number of cache lines hit
in the fast path.
- Extend TCP drop-reason support to cover PAWS checks.
Driver API
----------
- Reorganize PTP ioctl flag support to require an explicit opt-in for
the drivers, avoiding the problem of drivers not rejecting new
unsupported flags.
- Converted several device drivers to timestamping APIs.
- Introduce per-PHY ethtool dump helpers, improving the support for
dump operations targeting PHYs.
Tests and tooling
-----------------
- Add support for classic netlink in user space C codegen, so that
ynl-c can now read, create and modify links, routes addresses and
qdisc layer configuration.
- Add ynl sub-types for binary attributes, allowing ynl-c to output
known struct instead of raw binary data, clarifying the classic
netlink output.
- Extend MPTCP selftests to improve the code-coverage.
- Add tests for XDP tail adjustment in AF_XDP.
New hardware / drivers
----------------------
- OpenVPN virtual driver: offload OpenVPN data channels processing
to the kernel-space, increasing the data transfer throughput WRT
the user-space implementation.
- Renesas glue driver for the gigabit ethernet RZ/V2H(P) SoC.
- Broadcom asp-v3.0 ethernet driver.
- AMD Renoir ethernet device.
- ReakTek MT9888 2.5G ethernet PHY driver.
- Aeonsemi 10G C45 PHYs driver.
Drivers
-------
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- refactor the stearing table handling to reduce significantly
the amount of memory used
- add support for complex matches in H/W flow steering
- improve flow streeing error handling
- convert to netdev instance locking
- Intel (100G, ice, igb, ixgbe, idpf):
- ice: add switchdev support for LLDP traffic over VF
- ixgbe: add firmware manipulation and regions devlink support
- igb: introduce support for frame transmission premption
- igb: adds persistent NAPI configuration
- idpf: introduce RDMA support
- idpf: add initial PTP support
- Meta (fbnic):
- extend hardware stats coverage
- add devlink dev flash support
- Broadcom (bnxt):
- add support for RX-side device memory TCP
- Wangxun (txgbe):
- implement support for udp tunnel offload
- complete PTP and SRIOV support for AML 25G/10G devices
- Ethernet NICs embedded and virtual:
- Google (gve):
- add device memory TCP TX support
- Amazon (ena):
- support persistent per-NAPI config
- Airoha:
- add H/W support for L2 traffic offload
- add per flow stats for flow offloading
- RealTek (rtl8211): add support for WoL magic packet
- Synopsys (stmmac):
- dwmac-socfpga 1000BaseX support
- add Loongson-2K3000 support
- introduce support for hardware-accelerated VLAN stripping
- Broadcom (bcmgenet):
- expose more H/W stats
- Freescale (enetc, dpaa2-eth):
- enetc: add MAC filter, VLAN filter RSS and loopback support
- dpaa2-eth: convert to H/W timestamping APIs
- vxlan: convert FDB table to rhashtable, for better scalabilty
- veth: apply qdisc backpressure on full ring to reduce TX drops
- Ethernet switches:
- Microchip (kzZ88x3): add ETS scheduler support
- Ethernet PHYs:
- RealTek (rtl8211):
- add support for WoL magic packet
- add support for PHY LEDs
- CAN:
- Adds RZ/G3E CANFD support to the rcar_canfd driver.
- Preparatory work for CAN-XL support.
- Add self-tests framework with support for CAN physical interfaces.
- WiFi:
- mac80211:
- scan improvements with multi-link operation (MLO)
- Qualcomm (ath12k):
- enable AHB support for IPQ5332
- add monitor interface support to QCN9274
- add multi-link operation support to WCN7850
- add 802.11d scan offload support to WCN7850
- monitor mode for WCN7850, better 6 GHz regulatory
- Qualcomm (ath11k):
- restore hibernation support
- MediaTek (mt76):
- WiFi-7 improvements
- implement support for mt7990
- Intel (iwlwifi):
- enhanced multi-link single-radio (EMLSR) support on 5 GHz links
- rework device configuration
- RealTek (rtw88):
- improve throughput for RTL8814AU
- RealTek (rtw89):
- add multi-link operation support
- STA/P2P concurrency improvements
- support different SAR configs by antenna
- Bluetooth:
- introduce HCI Driver protocol
- btintel_pcie: do not generate coredump for diagnostic events
- btusb: add HCI Drv commands for configuring altsetting
- btusb: add RTL8851BE device 0x0bda:0xb850
- btusb: add new VID/PID 13d3/3584 for MT7922
- btusb: add new VID/PID 13d3/3630 and 13d3/3613 for MT7925
- btnxpuart: implement host-wakeup feature
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=t/Tz
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Implement the Device Memory TCP transmit path, allowing zero-copy
data transmission on top of TCP from e.g. GPU memory to the wire.
- Move all the IPv6 routing tables management outside the RTNL scope,
under its own lock and RCU. The route control path is now 3x times
faster.
- Convert queue related netlink ops to instance lock, reducing again
the scope of the RTNL lock. This improves the control plane
scalability.
- Refactor the software crc32c implementation, removing unneeded
abstraction layers and improving significantly the related
micro-benchmarks.
- Optimize the GRO engine for UDP-tunneled traffic, for a 10%
performance improvement in related stream tests.
- Cover more per-CPU storage with local nested BH locking; this is a
prep work to remove the current per-CPU lock in local_bh_disable()
on PREMPT_RT.
- Introduce and use nlmsg_payload helper, combining buffer bounds
verification with accessing payload carried by netlink messages.
Netfilter:
- Rewrite the procfs conntrack table implementation, improving
considerably the dump performance. A lot of user-space tools still
use this interface.
- Implement support for wildcard netdevice in netdev basechain and
flowtables.
- Integrate conntrack information into nft trace infrastructure.
- Export set count and backend name to userspace, for better
introspection.
BPF:
- BPF qdisc support: BPF-qdisc can be implemented with BPF struct_ops
programs and can be controlled in similar way to traditional qdiscs
using the "tc qdisc" command.
- Refactor the UDP socket iterator, addressing long standing issues
WRT duplicate hits or missed sockets.
Protocols:
- Improve TCP receive buffer auto-tuning and increase the default
upper bound for the receive buffer; overall this improves the
single flow maximum thoughput on 200Gbs link by over 60%.
- Add AFS GSSAPI security class to AF_RXRPC; it provides transport
security for connections to the AFS fileserver and VL server.
- Improve TCP multipath routing, so that the sources address always
matches the nexthop device.
- Introduce SO_PASSRIGHTS for AF_UNIX, to allow disabling SCM_RIGHTS,
and thus preventing DoS caused by passing around problematic FDs.
- Retire DCCP socket. DCCP only receives updates for bugs, and major
distros disable it by default. Its removal allows for better
organisation of TCP fields to reduce the number of cache lines hit
in the fast path.
- Extend TCP drop-reason support to cover PAWS checks.
Driver API:
- Reorganize PTP ioctl flag support to require an explicit opt-in for
the drivers, avoiding the problem of drivers not rejecting new
unsupported flags.
- Converted several device drivers to timestamping APIs.
- Introduce per-PHY ethtool dump helpers, improving the support for
dump operations targeting PHYs.
Tests and tooling:
- Add support for classic netlink in user space C codegen, so that
ynl-c can now read, create and modify links, routes addresses and
qdisc layer configuration.
- Add ynl sub-types for binary attributes, allowing ynl-c to output
known struct instead of raw binary data, clarifying the classic
netlink output.
- Extend MPTCP selftests to improve the code-coverage.
- Add tests for XDP tail adjustment in AF_XDP.
New hardware / drivers:
- OpenVPN virtual driver: offload OpenVPN data channels processing to
the kernel-space, increasing the data transfer throughput WRT the
user-space implementation.
- Renesas glue driver for the gigabit ethernet RZ/V2H(P) SoC.
- Broadcom asp-v3.0 ethernet driver.
- AMD Renoir ethernet device.
- ReakTek MT9888 2.5G ethernet PHY driver.
- Aeonsemi 10G C45 PHYs driver.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- refactor the steering table handling to significantly
reduce the amount of memory used
- add support for complex matches in H/W flow steering
- improve flow streeing error handling
- convert to netdev instance locking
- Intel (100G, ice, igb, ixgbe, idpf):
- ice: add switchdev support for LLDP traffic over VF
- ixgbe: add firmware manipulation and regions devlink support
- igb: introduce support for frame transmission premption
- igb: adds persistent NAPI configuration
- idpf: introduce RDMA support
- idpf: add initial PTP support
- Meta (fbnic):
- extend hardware stats coverage
- add devlink dev flash support
- Broadcom (bnxt):
- add support for RX-side device memory TCP
- Wangxun (txgbe):
- implement support for udp tunnel offload
- complete PTP and SRIOV support for AML 25G/10G devices
- Ethernet NICs embedded and virtual:
- Google (gve):
- add device memory TCP TX support
- Amazon (ena):
- support persistent per-NAPI config
- Airoha:
- add H/W support for L2 traffic offload
- add per flow stats for flow offloading
- RealTek (rtl8211): add support for WoL magic packet
- Synopsys (stmmac):
- dwmac-socfpga 1000BaseX support
- add Loongson-2K3000 support
- introduce support for hardware-accelerated VLAN stripping
- Broadcom (bcmgenet):
- expose more H/W stats
- Freescale (enetc, dpaa2-eth):
- enetc: add MAC filter, VLAN filter RSS and loopback support
- dpaa2-eth: convert to H/W timestamping APIs
- vxlan: convert FDB table to rhashtable, for better scalabilty
- veth: apply qdisc backpressure on full ring to reduce TX drops
- Ethernet switches:
- Microchip (kzZ88x3): add ETS scheduler support
- Ethernet PHYs:
- RealTek (rtl8211):
- add support for WoL magic packet
- add support for PHY LEDs
- CAN:
- Adds RZ/G3E CANFD support to the rcar_canfd driver.
- Preparatory work for CAN-XL support.
- Add self-tests framework with support for CAN physical interfaces.
- WiFi:
- mac80211:
- scan improvements with multi-link operation (MLO)
- Qualcomm (ath12k):
- enable AHB support for IPQ5332
- add monitor interface support to QCN9274
- add multi-link operation support to WCN7850
- add 802.11d scan offload support to WCN7850
- monitor mode for WCN7850, better 6 GHz regulatory
- Qualcomm (ath11k):
- restore hibernation support
- MediaTek (mt76):
- WiFi-7 improvements
- implement support for mt7990
- Intel (iwlwifi):
- enhanced multi-link single-radio (EMLSR) support on 5 GHz links
- rework device configuration
- RealTek (rtw88):
- improve throughput for RTL8814AU
- RealTek (rtw89):
- add multi-link operation support
- STA/P2P concurrency improvements
- support different SAR configs by antenna
- Bluetooth:
- introduce HCI Driver protocol
- btintel_pcie: do not generate coredump for diagnostic events
- btusb: add HCI Drv commands for configuring altsetting
- btusb: add RTL8851BE device 0x0bda:0xb850
- btusb: add new VID/PID 13d3/3584 for MT7922
- btusb: add new VID/PID 13d3/3630 and 13d3/3613 for MT7925
- btnxpuart: implement host-wakeup feature"
* tag 'net-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1611 commits)
selftests/bpf: Fix bpf selftest build warning
selftests: netfilter: Fix skip of wildcard interface test
net: phy: mscc: Stop clearing the the UDPv4 checksum for L2 frames
net: openvswitch: Fix the dead loop of MPLS parse
calipso: Don't call calipso functions for AF_INET sk.
selftests/tc-testing: Add a test for HFSC eltree double add with reentrant enqueue behaviour on netem
net_sched: hfsc: Address reentrant enqueue adding class to eltree twice
octeontx2-pf: QOS: Refactor TC_HTB_LEAF_DEL_LAST callback
octeontx2-pf: QOS: Perform cache sync on send queue teardown
net: mana: Add support for Multi Vports on Bare metal
net: devmem: ncdevmem: remove unused variable
net: devmem: ksft: upgrade rx test to send 1K data
net: devmem: ksft: add 5 tuple FS support
net: devmem: ksft: add exit_wait to make rx test pass
net: devmem: ksft: add ipv4 support
net: devmem: preserve sockc_err
page_pool: fix ugly page_pool formatting
net: devmem: move list_add to net_devmem_bind_dmabuf.
selftests: netfilter: nft_queue.sh: include file transfer duration in log message
net: phy: mscc: Fix memory leak when using one step timestamping
...
ACPI, EFI and PSCI:
- Decouple Arm's "Software Delegated Exception Interface" (SDEI)
support from the ACPI GHES code so that it can be used by platforms
booted with device-tree.
- Remove unnecessary per-CPU tracking of the FPSIMD state across EFI
runtime calls.
- Fix a node refcount imbalance in the PSCI device-tree code.
CPU Features:
- Ensure register sanitisation is applied to fields in ID_AA64MMFR4.
- Expose AIDR_EL1 to userspace via sysfs, primarily so that KVM guests
can reliably query the underlying CPU types from the VMM.
- Re-enabling of SME support (CONFIG_ARM64_SME) as a result of fixes
to our context-switching, signal handling and ptrace code.
Entry code:
- Hook up TIF_NEED_RESCHED_LAZY so that CONFIG_PREEMPT_LAZY can be
selected.
Memory management:
- Prevent BSS exports from being used by the early PI code.
- Propagate level and stride information to the low-level TLB
invalidation routines when operating on hugetlb entries.
- Use the page-table contiguous hint for vmap() mappings with
VM_ALLOW_HUGE_VMAP where possible.
- Optimise vmalloc()/vmap() page-table updates to use "lazy MMU mode"
and hook this up on arm64 so that the trailing DSB (used to publish
the updates to the hardware walker) can be deferred until the end of
the mapping operation.
- Extend mmap() randomisation for 52-bit virtual addresses (on par with
48-bit addressing) and remove limited support for randomisation of
the linear map.
Perf and PMUs:
- Add support for probing the CMN-S3 driver using ACPI.
- Minor driver fixes to the CMN, Arm-NI and amlogic PMU drivers.
Selftests:
- Fix FPSIMD and SME tests to align with the freshly re-enabled SME
support.
- Fix default setting of the OUTPUT variable so that tests are
installed in the right location.
vDSO:
- Replace raw counter access from inline assembly code with a call to
the the __arch_counter_get_cntvct() helper function.
Miscellaneous:
- Add some missing header inclusions to the CCA headers.
- Rework rendering of /proc/cpuinfo to follow the x86-approach and
avoid repeated buffer expansion (the user-visible format remains
identical).
- Remove redundant selection of CONFIG_CRC32
- Extend early error message when failing to map the device-tree blob.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmg1uTgQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNFv2CAC9S5OW0btOAo7V/LFBpLhJM3hdIV6Sn6N1
d/K5znuqPBG6VPfBrshaZltEl/C3U8KG4H8xrlX5cSo7CRuf3DgVBw3kiZ6ERZj6
1gnKR54juA1oWhcroPl0s76ETWj3N4gO036u2qOhWNAYflDunh1+bCIGJkG4H/yP
wqtWn974YUbad/zQJSbG3IMO1yvxZ/PsNpVF8HjyQ0/ZPWsYTscrhNQ0hWro17sR
CTcUaGxH4GrXW24EGNgkLB9aq67X2rtGGtaIlp5oFl8FuLklc7TYbPwJp8cPCTNm
0Sp0mpuR9M675pYIKoCI9m5twc46znRIKmbXi5LvPd77418y3jTf
=03N4
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The headline feature is the re-enablement of support for Arm's
Scalable Matrix Extension (SME) thanks to a bumper crop of fixes
from Mark Rutland.
If matrices aren't your thing, then Ryan's page-table optimisation
work is much more interesting.
Summary:
ACPI, EFI and PSCI:
- Decouple Arm's "Software Delegated Exception Interface" (SDEI)
support from the ACPI GHES code so that it can be used by platforms
booted with device-tree
- Remove unnecessary per-CPU tracking of the FPSIMD state across EFI
runtime calls
- Fix a node refcount imbalance in the PSCI device-tree code
CPU Features:
- Ensure register sanitisation is applied to fields in ID_AA64MMFR4
- Expose AIDR_EL1 to userspace via sysfs, primarily so that KVM
guests can reliably query the underlying CPU types from the VMM
- Re-enabling of SME support (CONFIG_ARM64_SME) as a result of fixes
to our context-switching, signal handling and ptrace code
Entry code:
- Hook up TIF_NEED_RESCHED_LAZY so that CONFIG_PREEMPT_LAZY can be
selected
Memory management:
- Prevent BSS exports from being used by the early PI code
- Propagate level and stride information to the low-level TLB
invalidation routines when operating on hugetlb entries
- Use the page-table contiguous hint for vmap() mappings with
VM_ALLOW_HUGE_VMAP where possible
- Optimise vmalloc()/vmap() page-table updates to use "lazy MMU mode"
and hook this up on arm64 so that the trailing DSB (used to publish
the updates to the hardware walker) can be deferred until the end
of the mapping operation
- Extend mmap() randomisation for 52-bit virtual addresses (on par
with 48-bit addressing) and remove limited support for
randomisation of the linear map
Perf and PMUs:
- Add support for probing the CMN-S3 driver using ACPI
- Minor driver fixes to the CMN, Arm-NI and amlogic PMU drivers
Selftests:
- Fix FPSIMD and SME tests to align with the freshly re-enabled SME
support
- Fix default setting of the OUTPUT variable so that tests are
installed in the right location
vDSO:
- Replace raw counter access from inline assembly code with a call to
the the __arch_counter_get_cntvct() helper function
Miscellaneous:
- Add some missing header inclusions to the CCA headers
- Rework rendering of /proc/cpuinfo to follow the x86-approach and
avoid repeated buffer expansion (the user-visible format remains
identical)
- Remove redundant selection of CONFIG_CRC32
- Extend early error message when failing to map the device-tree
blob"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (83 commits)
arm64: cputype: Add cputype definition for HIP12
arm64: el2_setup.h: Make __init_el2_fgt labels consistent, again
perf/arm-cmn: Add CMN S3 ACPI binding
arm64/boot: Disallow BSS exports to startup code
arm64/boot: Move global CPU override variables out of BSS
arm64/boot: Move init_pgdir[] and init_idmap_pgdir[] into __pi_ namespace
perf/arm-cmn: Initialise cmn->cpu earlier
kselftest/arm64: Set default OUTPUT path when undefined
arm64: Update comment regarding values in __boot_cpu_mode
arm64: mm: Drop redundant check in pmd_trans_huge()
arm64/mm: Re-organise setting up FEAT_S1PIE registers PIRE0_EL1 and PIR_EL1
arm64/mm: Permit lazy_mmu_mode to be nested
arm64/mm: Disable barrier batching in interrupt contexts
arm64/cpuinfo: only show one cpu's info in c_show()
arm64/mm: Batch barriers when updating kernel mappings
mm/vmalloc: Enter lazy mmu mode while manipulating vmalloc ptes
arm64/mm: Support huge pte-mapped pages in vmap
mm/vmalloc: Gracefully unmap huge ptes
mm/vmalloc: Warn on improper use of vunmap_range()
arm64/mm: Hoist barriers out of set_ptes_anysz() loop
...
- Use strscpy() and simply setup_cpuinfo()
- Remove conflicting mappings when flushing tlb entries
- Force update_mmu_cache on spurious pagefaults
-----BEGIN PGP SIGNATURE-----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=1mO5
-----END PGP SIGNATURE-----
Merge tag 'nios2_updates_for_v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux
Pull nios2 updates fromDinh Nguyen:
- Use strscpy() and simply setup_cpuinfo()
- Remove conflicting mappings when flushing tlb entries
- Force update_mmu_cache on spurious pagefaults
* tag 'nios2_updates_for_v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
nios2: Replace strcpy() with strscpy() and simplify setup_cpuinfo()
nios2: do not introduce conflicting mappings when flushing tlb entries
nios2: force update_mmu_cache on spurious tlb-permission--related pagefaults
-----BEGIN PGP SIGNATURE-----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=OyPV
-----END PGP SIGNATURE-----
Merge tag 'jfs-6.16' of github.com:kleikamp/linux-shaggy
Pull jfs updates from David Kleikamp:
"A few small fixes for jfs"
* tag 'jfs-6.16' of github.com:kleikamp/linux-shaggy:
jfs: fix array-index-out-of-bounds read in add_missing_indices
jfs: Fix null-ptr-deref in jfs_ioc_trim
jfs: validate AG parameters in dbMount() to prevent crashes
This set fixes delays when shutting down SCTP connections, and updates
dlm Kconfig for SCTP.
-----BEGIN PGP SIGNATURE-----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=pFlu
-----END PGP SIGNATURE-----
Merge tag 'dlm-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm updates from David Teigland:
"This fixes delays when shutting down SCTP connections, and updates dlm
Kconfig for SCTP"
* tag 'dlm-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: drop SCTP Kconfig dependency
dlm: reject SCTP configuration if not enabled
dlm: use SHUT_RDWR for SCTP shutdown
dlm: mask sk_shutdown value
The marquee feature for this release is that the limit on the
maximum rsize and wsize has been raised to 4MB. The default remains
at 1MB, but risk-seeking administrators now have the ability to try
larger I/O sizes with NFS clients that support them. Eventually the
default setting will be increased when we have confidence that this
change will not have negative impact.
With v6.16, NFSD now has its own debugfs file system where we can
add experimental features and make them available outside of our
development community without impacting production deployments. The
first experimental setting added is one that makes all NFS READ
operations use vfs_iter_read() instead of the NFSD splice actor. The
plan is to eventually retire the splice actor, as that will enable a
number of new capabilities such as the use of struct bio_vec from the
top to the bottom of the NFSD stack.
Jeff Layton contributed a number of observability improvements. The
use of dprintk() in a number of high-traffic code paths has been
replaced with static trace points.
This release sees the continuation of efforts to harden the NFSv4.2
COPY operation. Soon, the restriction on async COPY operations can
be lifted.
Many thanks to the contributors, reviewers, testers, and bug
reporters who participated during the v6.16 development cycle.
-----BEGIN PGP SIGNATURE-----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=FbeG
-----END PGP SIGNATURE-----
Merge tag 'nfsd-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd updates from Chuck Lever:
"The marquee feature for this release is that the limit on the maximum
rsize and wsize has been raised to 4MB. The default remains at 1MB,
but risk-seeking administrators now have the ability to try larger I/O
sizes with NFS clients that support them. Eventually the default
setting will be increased when we have confidence that this change
will not have negative impact.
With v6.16, NFSD now has its own debugfs file system where we can add
experimental features and make them available outside of our
development community without impacting production deployments. The
first experimental setting added is one that makes all NFS READ
operations use vfs_iter_read() instead of the NFSD splice actor. The
plan is to eventually retire the splice actor, as that will enable a
number of new capabilities such as the use of struct bio_vec from the
top to the bottom of the NFSD stack.
Jeff Layton contributed a number of observability improvements. The
use of dprintk() in a number of high-traffic code paths has been
replaced with static trace points.
This release sees the continuation of efforts to harden the NFSv4.2
COPY operation. Soon, the restriction on async COPY operations can be
lifted.
Many thanks to the contributors, reviewers, testers, and bug reporters
who participated during the v6.16 development cycle"
* tag 'nfsd-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux: (60 commits)
xdrgen: Fix code generated for counted arrays
SUNRPC: Bump the maximum payload size for the server
NFSD: Add a "default" block size
NFSD: Remove NFSSVC_MAXBLKSIZE_V2 macro
NFSD: Remove NFSD_BUFSIZE
sunrpc: Remove the RPCSVC_MAXPAGES macro
svcrdma: Adjust the number of entries in svc_rdma_send_ctxt::sc_pages
svcrdma: Adjust the number of entries in svc_rdma_recv_ctxt::rc_pages
sunrpc: Adjust size of socket's receive page array dynamically
SUNRPC: Remove svc_rqst :: rq_vec
SUNRPC: Remove svc_fill_write_vector()
NFSD: Use rqstp->rq_bvec in nfsd_iter_write()
SUNRPC: Export xdr_buf_to_bvec()
NFSD: De-duplicate the svc_fill_write_vector() call sites
NFSD: Use rqstp->rq_bvec in nfsd_iter_read()
sunrpc: Replace the rq_bvec array with dynamically-allocated memory
sunrpc: Replace the rq_pages array with dynamically-allocated memory
sunrpc: Remove backchannel check in svc_init_buffer()
sunrpc: Add a helper to derive maxpages from sv_max_mesg
svcrdma: Reduce the number of rdma_rw contexts per-QP
...
* Fast commit performance improvements
* Multi-fsblock atomic write support for bigalloc file systems
* Large folio support for regular files
This last can result in really stupendous performance for the right
workloads. For example, see [1] where the Kernel Test Robot reported
over 37% improvement on a large sequential I/O workload.
[1] https://lore.kernel.org/all/202505161418.ec0d753f-lkp@intel.com/
There are also the usual bug fixes and cleanups. Of note are cleanups
of the extent status tree to fix potential races that could result in
the extent status tree getting corrupted under heavy siulatneous
allocation and deallocation to a single file.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAmg2GJgACgkQ8vlZVpUN
gaOmmgf/fEh2OPDG6aAJpQ6hjy2WIbrxqTyuWC/+AFnyI5/Jy0Iskis3lHBiFdKP
IFjgC1h9CB5ARVvOLd7NOgflPHSSHsnYqoTCS6J4tdWvFN4VRiHe2J3fdTZd/bea
dzdWniHS3SAJiQm4wvbkhluFgecItBHYzDltapkHI0OGepxZt3thWVvbay6veO9R
ChXQ7T7/9eUZa5N5IVUeJmWobgh0RD+DgtwCih59UDfnezGqiDr6/shpyNC6EvWV
oZdvJw2+2DCPn5+DF4Ut77mLpKnxorQ4osNPOovZf59JnSyEcCmbBDuvyNfRldfC
yQYoCFkOv0Fz8tgJbtoAN71+YXl66w==
=fxDh
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"New ext4 features and performance improvements:
- Fast commit performance improvements
- Multi-fsblock atomic write support for bigalloc file systems
- Large folio support for regular files
This last can result in really stupendous performance for the right
workloads. For example, see [1] where the Kernel Test Robot reported
over 37% improvement on a large sequential I/O workload.
There are also the usual bug fixes and cleanups. Of note are cleanups
of the extent status tree to fix potential races that could result in
the extent status tree getting corrupted under heavy simultaneous
allocation and deallocation to a single file"
Link: https://lore.kernel.org/all/202505161418.ec0d753f-lkp@intel.com/ [1]
* tag 'ext4_for_linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (52 commits)
ext4: Add a WARN_ON_ONCE for querying LAST_IN_LEAF instead
ext4: Simplify flags in ext4_map_query_blocks()
ext4: Rename and document EXT4_EX_FILTER to EXT4_EX_QUERY_FILTER
ext4: Simplify last in leaf check in ext4_map_query_blocks
ext4: Unwritten to written conversion requires EXT4_EX_NOCACHE
ext4: only dirty folios when data journaling regular files
ext4: Add atomic block write documentation
ext4: Enable support for ext4 multi-fsblock atomic write using bigalloc
ext4: Add multi-fsblock atomic write support with bigalloc
ext4: Add support for EXT4_GET_BLOCKS_QUERY_LEAF_BLOCKS
ext4: Make ext4_meta_trans_blocks() non-static for later use
ext4: Check if inode uses extents in ext4_inode_can_atomic_write()
ext4: Document an edge case for overwrites
jbd2: remove journal_t argument from jbd2_superblock_csum()
jbd2: remove journal_t argument from jbd2_chksum()
ext4: remove sb argument from ext4_superblock_csum()
ext4: remove sbi argument from ext4_chksum()
ext4: enable large folio for regular file
ext4: make online defragmentation support large folios
ext4: make the writeback path support large folios
...
Code from Eric Sandeen at redhat that converts orangefs over to the new
mount API.
-----BEGIN PGP SIGNATURE-----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=CtqS
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.16-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs update from Mike Marshall:
"Convert to use the new mount API.
Code from Eric Sandeen at redhat that converts orangefs over to the
new mount API"
* tag 'for-linus-6.16-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: Convert to use the new mount API
-----BEGIN PGP SIGNATURE-----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=zeWb
-----END PGP SIGNATURE-----
Merge tag 'for-6.16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"A fixup to the xarray conversion sent in the main 6.16 batch. It was
not included because it would cause rebase/refresh of like 80 patches,
right before sending the early pull request last week.
It's fixing a bug when zoned mode is enabled on btrfs so it's not
affecting most people"
* tag 'for-6.16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: don't drop a reference if btrfs_check_write_meta_pointer() fails
new drivers:
- bring in the asahi uapi header standalone
- nova-drm: stub driver
rust dependencies (for nova-core):
- auxiliary
- bus abstractions
- driver registration
- sample driver
- devres changes from driver-core
- revocable changes
core:
- add Apple fourcc modifiers
- add virtio capset definitions
- extend EXPORT_SYNC_FILE for timeline syncobjs
- convert to devm_platform_ioremap_resource
- refactor shmem helper page pinning
- DP powerup/down link helpers
- remove disgusting turds
- extended %p4cc in vsprintf.c to support fourcc prints
- change vsprintf %p4cn to %p4chR, remove %p4cn
- Add drm_file_err function
- IN_FORMATS_ASYNC property
- move sitronix from tiny to their own subdir
rust:
- add drm core infrastructure rust abstractions
(device/driver, ioctl, file, gem)
dma-buf:
- adjust sg handling to not cache map on attach
- allow setting dma-device for import
- Add a helper to sort and deduplicate dma_fence arrays
docs:
- updated drm scheduler docs
- fbdev todo update
- fb rendering
- actual brightness
ttm:
- fix delayed destroy resv object
bridge:
- add kunit tests
- convert tc358775 to atomic
- convert drivers to devm_drm_bridge_alloc
- convert rk3066_hdmi to bridge driver
scheduler:
- add kunit tests
panel:
- refcount panels to improve lifetime handling
- Powertip PH128800T004-ZZA01
- NLT NL13676BC25-03F, Tianma TM070JDHG34-00
- Himax HX8279/HX8279-D DDIC
- Visionox G2647FB105
- Sitronix ST7571
- ZOTAC rotation quirk
vkms:
- allow attaching more displays
i915:
- xe3lpd display updates
- vrr refactor
- intel_display struct conversions
- xe2hpd memory type identification
- add link rate/count to i915_display_info
- cleanup VGA plane handling
- refactor HDCP GSC
- fix SLPC wait boosting reference counting
- add 20ms delay to engine reset
- fix fence release on early probe errors
xe:
- SRIOV updates
- BMG PCI ID update
- support separate firmware for each GT
- SVM fix, prelim SVM multi-device work
- export fan speed
- temp disable d3cold on BMG
- backup VRAM in PM notifier instead of suspend/freeze
- update xe_ttm_access_memory to use GPU for non-visible access
- fix guc_info debugfs for VFs
- use copy_from_user instead of __copy_from_user
- append PCIe gen5 limitations to xe_firmware document
amdgpu:
- DSC cleanup
- DC Scaling updates
- Fused I2C-over-AUX updates
- DMUB updates
- Use drm_file_err in amdgpu
- Enforce isolation updates
- Use new dma_fence helpers
- USERQ fixes
- Documentation updates
- SR-IOV updates
- RAS updates
- PSP 12 cleanups
- GC 9.5 updates
- SMU 13.x updates
- VCN / JPEG SR-IOV updates
amdkfd:
- Update error messages for SDMA
- Userptr updates
- XNACK fixes
radeon:
- CIK doorbell cleanup
nouveau:
- add support for NVIDIA r570 GSP firmware
- enable Hopper/Blackwell support
nova-core:
- fix task list
- register definition infrastructure
- move firmware into own rust module
- register auxiliary device for nova-drm
nova-drm:
- initial driver skeleton
msm:
- GPU:
- ACD (adaptive clock distribution) for X1-85
- drop fictional address_space_size
- improve GMU HFI response time out robustness
- fix crash when throttling during boot
- DPU:
- use single CTL path for flushing on DPU 5.x+
- improve SSPP allocation code for better sharing
- Enabled SmartDMA on SM8150, SC8180X, SC8280XP, SM8550
- Added SAR2130P support
- Disabled DSC support on MSM8937, MSM8917, MSM8953, SDM660
- DP:
- switch to new audio helpers
- better LTTPR handling
- DSI:
- Added support for SA8775P
- Added SAR2130P support
- HDMI:
- Switched to use new helpers for ACR data
- Fixed old standing issue of HPD not working in some cases
amdxdna:
- add dma-buf support
- allow empty command submits
renesas:
- add dma-buf support
- add zpos, alpha, blend support
panthor:
- fail properly for NO_MMAP bos
- add SET_LABEL ioctl
- debugfs BO dumping support
imagination:
- update DT bindings
- support TI AM68 GPU
hibmc:
- improve interrupt handling and HPD support
virtio:
- add panic handler support
rockchip:
- add RK3588 support
- add DP AUX bus panel support
ivpu:
- add heartbeat based hangcheck
mediatek:
- prepares support for MT8195/99 HDMIv2/DDCv2
anx7625:
- improve HPD
tegra:
- speed up firmware loading
-----BEGIN PGP SIGNATURE-----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=jpVr
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-05-28' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"As part of building up nova-core/nova-drm pieces we've brought in some
rust abstractions through this tree, aux bus being the main one, with
devres changes also in the driver-core tree. Along with the drm core
abstractions and enough nova-core/nova-drm to use them. This is still
all stub work under construction, to build the nova driver upstream.
The other big NVIDIA related one is nouveau adds support for
Hopper/Blackwell GPUs, this required a new GSP firmware update to
570.144, and a bunch of rework in order to support multiple fw
interfaces.
There is also the introduction of an asahi uapi header file as a
precursor to getting the real driver in later, but to unblock
userspace mesa packages while the driver is trapped behind rust
enablement.
Otherwise it's the usual mixture of stuff all over, amdgpu, i915/xe,
and msm being the main ones, and some changes to vsprintf.
new drivers:
- bring in the asahi uapi header standalone
- nova-drm: stub driver
rust dependencies (for nova-core):
- auxiliary
- bus abstractions
- driver registration
- sample driver
- devres changes from driver-core
- revocable changes
core:
- add Apple fourcc modifiers
- add virtio capset definitions
- extend EXPORT_SYNC_FILE for timeline syncobjs
- convert to devm_platform_ioremap_resource
- refactor shmem helper page pinning
- DP powerup/down link helpers
- extended %p4cc in vsprintf.c to support fourcc prints
- change vsprintf %p4cn to %p4chR, remove %p4cn
- Add drm_file_err function
- IN_FORMATS_ASYNC property
- move sitronix from tiny to their own subdir
rust:
- add drm core infrastructure rust abstractions
(device/driver, ioctl, file, gem)
dma-buf:
- adjust sg handling to not cache map on attach
- allow setting dma-device for import
- Add a helper to sort and deduplicate dma_fence arrays
docs:
- updated drm scheduler docs
- fbdev todo update
- fb rendering
- actual brightness
ttm:
- fix delayed destroy resv object
bridge:
- add kunit tests
- convert tc358775 to atomic
- convert drivers to devm_drm_bridge_alloc
- convert rk3066_hdmi to bridge driver
scheduler:
- add kunit tests
panel:
- refcount panels to improve lifetime handling
- Powertip PH128800T004-ZZA01
- NLT NL13676BC25-03F, Tianma TM070JDHG34-00
- Himax HX8279/HX8279-D DDIC
- Visionox G2647FB105
- Sitronix ST7571
- ZOTAC rotation quirk
vkms:
- allow attaching more displays
i915:
- xe3lpd display updates
- vrr refactor
- intel_display struct conversions
- xe2hpd memory type identification
- add link rate/count to i915_display_info
- cleanup VGA plane handling
- refactor HDCP GSC
- fix SLPC wait boosting reference counting
- add 20ms delay to engine reset
- fix fence release on early probe errors
xe:
- SRIOV updates
- BMG PCI ID update
- support separate firmware for each GT
- SVM fix, prelim SVM multi-device work
- export fan speed
- temp disable d3cold on BMG
- backup VRAM in PM notifier instead of suspend/freeze
- update xe_ttm_access_memory to use GPU for non-visible access
- fix guc_info debugfs for VFs
- use copy_from_user instead of __copy_from_user
- append PCIe gen5 limitations to xe_firmware document
amdgpu:
- DSC cleanup
- DC Scaling updates
- Fused I2C-over-AUX updates
- DMUB updates
- Use drm_file_err in amdgpu
- Enforce isolation updates
- Use new dma_fence helpers
- USERQ fixes
- Documentation updates
- SR-IOV updates
- RAS updates
- PSP 12 cleanups
- GC 9.5 updates
- SMU 13.x updates
- VCN / JPEG SR-IOV updates
amdkfd:
- Update error messages for SDMA
- Userptr updates
- XNACK fixes
radeon:
- CIK doorbell cleanup
nouveau:
- add support for NVIDIA r570 GSP firmware
- enable Hopper/Blackwell support
nova-core:
- fix task list
- register definition infrastructure
- move firmware into own rust module
- register auxiliary device for nova-drm
nova-drm:
- initial driver skeleton
msm:
- GPU:
- ACD (adaptive clock distribution) for X1-85
- drop fictional address_space_size
- improve GMU HFI response time out robustness
- fix crash when throttling during boot
- DPU:
- use single CTL path for flushing on DPU 5.x+
- improve SSPP allocation code for better sharing
- Enabled SmartDMA on SM8150, SC8180X, SC8280XP, SM8550
- Added SAR2130P support
- Disabled DSC support on MSM8937, MSM8917, MSM8953, SDM660
- DP:
- switch to new audio helpers
- better LTTPR handling
- DSI:
- Added support for SA8775P
- Added SAR2130P support
- HDMI:
- Switched to use new helpers for ACR data
- Fixed old standing issue of HPD not working in some cases
amdxdna:
- add dma-buf support
- allow empty command submits
renesas:
- add dma-buf support
- add zpos, alpha, blend support
panthor:
- fail properly for NO_MMAP bos
- add SET_LABEL ioctl
- debugfs BO dumping support
imagination:
- update DT bindings
- support TI AM68 GPU
hibmc:
- improve interrupt handling and HPD support
virtio:
- add panic handler support
rockchip:
- add RK3588 support
- add DP AUX bus panel support
ivpu:
- add heartbeat based hangcheck
mediatek:
- prepares support for MT8195/99 HDMIv2/DDCv2
anx7625:
- improve HPD
tegra:
- speed up firmware loading
* tag 'drm-next-2025-05-28' of https://gitlab.freedesktop.org/drm/kernel: (1627 commits)
drm/nouveau/tegra: Fix error pointer vs NULL return in nvkm_device_tegra_resource_addr()
drm/xe: Default auto_link_downgrade status to false
drm/xe/guc: Make creation of SLPC debugfs files conditional
drm/i915/display: Add check for alloc_ordered_workqueue() and alloc_workqueue()
drm/i915/dp_mst: Work around Thunderbolt sink disconnect after SINK_COUNT_ESI read
drm/i915/ptl: Use everywhere the correct DDI port clock select mask
drm/nouveau/kms: add support for GB20x
drm/dp: add option to disable zero sized address only transactions.
drm/nouveau: add support for GB20x
drm/nouveau/gsp: add hal for fifo.chan.doorbell_handle
drm/nouveau: add support for GB10x
drm/nouveau/gf100-: track chan progress with non-WFI semaphore release
drm/nouveau/nv50-: separate CHANNEL_GPFIFO handling out from CHANNEL_DMA
drm/nouveau: add helper functions for allocating pinned/cpu-mapped bos
drm/nouveau: add support for GH100
drm/nouveau: improve handling of 64-bit BARs
drm/nouveau/gv100-: switch to volta semaphore methods
drm/nouveau/gsp: support deeper page tables in COPY_SERVER_RESERVED_PDES
drm/nouveau/gsp: init client VMMs with NV0080_CTRL_DMA_SET_PAGE_DIRECTORY
drm/nouveau/gsp: fetch level shift and PDE from BAR2 VMM
...
