The kernel documentation specifies that the console option 'r' can
be used to enable hardware flow control for console writes. The 8250
driver does include code for hardware flow control on the console if
cons_flow is set, but there is no code path that actually sets this.
However, that is not the only issue. The problems are:
1. Specifying the console option 'r' does not lead to cons_flow being
set.
2. Even if cons_flow would be set, serial8250_register_8250_port()
clears it.
3. When the console option 'r' is specified, uart_set_options()
attempts to initialize the port for CRTSCTS. However, afterwards
it does not set the UPSTAT_CTS_ENABLE status bit and therefore on
boot, uart_cts_enabled() is always false. This policy bit is
important for console drivers as a criteria if they may poll CTS.
4. Even though uart_set_options() attempts to initialize the port
for CRTSCTS, the 8250 set_termios() callback does not enable the
RTS signal (TIOCM_RTS) and thus the hardware is not properly
initialized for CTS polling.
5. Even if modem control was properly setup for CTS polling
(TIOCM_RTS), uart_configure_port() clears TIOCM_RTS, thus
breaking CTS polling.
6. wait_for_xmitr() and serial8250_console_write() use cons_flow
to decide if CTS polling should occur. However, the condition
should also include a check that it is not in RS485 mode and
CRTSCTS is actually enabled in the hardware.
Address all these issues as conservatively as possible by gating them
behind checks focussed on the user specifying console hardware flow
control support and the hardware being configured for CTS polling
at the time of the write to the UART.
Since checking the UPSTAT_CTS_ENABLE status bit is a part of the new
condition gate, these changes also support runtime termios updates to
disable/enable CRTSCTS.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260511152706.151498-4-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_xmitr() calls wait_for_lsr() to wait for the transmission
registers to be empty. wait_for_lsr() can timeout after a reasonable
amount of time.
When console flow control is active, wait_for_xmitr() additionally
polls CTS, waiting for the peer to signal that it is ready to receive
more data.
If hardware flow control is enabled (auto CTS) and the peer deasserts
CTS, wait_for_lsr() will timeout. If additionally console flow
control is active and while polling CTS the peer asserts CTS, the
console will assume it can immediately transmit, even though the
transmission registers may not be empty. This can lead to data loss.
Avoid this problem by performing an extra wait_for_lsr() upon CTS
assertion if wait_for_lsr() previously timed out.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260511152706.151498-3-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since console flow control policy is no longer part of uart_port.flags,
explicitly set the policy for the port.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260511152706.151498-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_register_8250_port() conditionally copies uart->port.dev
from up->port.dev only when up->port.dev is non-NULL:
if (up->port.dev) {
uart->port.dev = up->port.dev;
...
}
So if both the existing uart slot and up have a NULL ->dev,
uart->port.dev remains NULL. The very next ACPI companion check
then dereferences it unconditionally:
if (!has_acpi_companion(uart->port.dev)) {
has_acpi_companion() reads dev->fwnode without a NULL guard
(include/linux/acpi.h), so this NULL-derefs the kernel for the
remaining no-dev case rather than just skipping the
mctrl_gpio_init() initialisation as intended.
smatch flags the inconsistency:
drivers/tty/serial/8250/8250_core.c:767
serial8250_register_8250_port() error: 'uart->port.dev' could be
null (see line 719)
Guard the call with a NULL check so register continues to work
for callers that legitimately have no parent device (legacy
non-OF/non-ACPI registrations).
No functional change for callers that pass a non-NULL ->dev.
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Link: https://patch.msgid.link/20260508181237.11146-1-sozdayvek@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic support for the A9 based Amlogic BY401 board, which describes
the following components: CPU, GIC, IRQ, Timer and UART.
These are capable of booting up into the serial console.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://patch.msgid.link/20260423-a9-baisc-dts-v4-2-c26b480a068c@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add bindings for the Amlogic BY401 board, using A311Y3 Soc from
Amlogic A9 family chip.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://patch.msgid.link/20260423-a9-baisc-dts-v4-1-c26b480a068c@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 20ffe4b333 ("serial: max310x: allow driver to be built with
SPI or I2C"), if I2C is enabled and SPI_MASTER is disabled, we have these
compile errors:
drivers/tty/serial/max310x.c: In function 'max310x_uart_init':
drivers/tty/serial/max310x.c: error: 'max310x_spi_driver' undeclared...
drivers/tty/serial/max310x.c: In function ‘max310x_uart_init’:
drivers/tty/serial/max310x.c: error: label ‘err_spi_register’
defined but not used...
drivers/tty/serial/max310x.c: error: ‘regcfg’ defined but not used
Fix by properly encapsulating i2c/spi code/variables in their respective
context with IS_ENABLED() macros for CONFIG_I2C and CONFIG_SPI_MASTER.
Also fix link failure with SERIAL_MAX310X=y and I2C=m by modifying Kconfig
depends.
Fixes: 20ffe4b333 ("serial: max310x: allow driver to be built with SPI or I2C")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202605121847.N9DVLNg2-lkp@intel.com/
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521153333.2336642-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_SERIAL_QCOM_GENI_CONSOLE is disabled, the driver still
advertises the debug UART compatible strings ("qcom,geni-debug-uart"
and "qcom,sa8255p-geni-debug-uart") in its of_match table. This lets the
driver match and probe console UART DT nodes even though console
support is not built. As a result, the console port is never registered
with the UART core and uart_add_one_port() fails with -EINVAL.
Fix this by only including the debug UART compatible entries in the
match table when CONFIG_SERIAL_QCOM_GENI_CONSOLE is enabled, preventing
the driver from probing console UART nodes when console support is
absent.
Reviewed-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Signed-off-by: Aniket Randive <aniket.randive@oss.qualcomm.com>
Link: https://patch.msgid.link/20260504101045.1084672-1-aniket.randive@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add comments to help clarify the provenance of the various hardcoded values
used in computing the ref clk.
Assisted-by: Gemini:Pro
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260417-max310x-2-v1-10-b424e105ecac@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
txlen, to_send and tail variables are only used within the while() loop.
Move them to that scope to keep them closer to their usage and improve
readability.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260417-max310x-2-v1-9-b424e105ecac@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If SPI is disabled, the max310x driver cannot be selected. Allow driver to
be selected if either I2C or SPI is set.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260417-max310x-2-v1-8-b424e105ecac@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same basic code is duplicated for each of the four PLL multiplier
values, so simplify and streamline it. Doing so allows us to avoid
some unnecessary (fdiv * factor) multiplications for some fdiv values and
replace the second "if" statement with an "else if" and avoid a useless
comparison.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260417-max310x-2-v1-5-b424e105ecac@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The baudrate used to compute the best error was changed from 115200 to
460800 in commit 35240ba26a ("tty: max310x: Fix invalid baudrate
divisors calculator"), but the comment was not updated, so fix it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260417-max310x-2-v1-4-b424e105ecac@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having max310x_set_ref_clk() return an s32 as both an error code
and a frequency value is ambiguous. Fix by passing a pointer to the
frequency value that will then be updated, and simply return a status.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260417-max310x-2-v1-3-b424e105ecac@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
besterr was defined as a signed type was to make sure that the first call
to max310x_update_best_err() would always set besterr. Also there is no
need for it to be a long. By changing its type to unsigned int and initial
value to UINT_MAX, max310x_update_best_err() can be simplified and be more
efficient while achieving the same initial result.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260417-max310x-2-v1-2-b424e105ecac@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
max310x_set_ref_clk() returns a 32-bits clock value, so there is no need
to have parameters and intermediate values defined as long. Change
clock and freq types to int.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260417-max310x-2-v1-1-b424e105ecac@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device has a minimum baud rate > 9600 bauds, and a new termios baud
rate of 0 (hang up) is requested, uart_get_baud_rate() will return 0.
Most drivers do not check this return value and call uart_update_timeout()
with this zero baud rate, which will trigger a "Division by zero in kernel"
fault:
stty -F /dev/ttySC0 0
Division by zero in kernel.
...
Fix by returning the larger of 9600 or min for the B0 case. This now
ensures that a non-zero baud rate is returned, and greatly simplifies the
code.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260410152022.2146488-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the clipping logic in uart_get_baud_rate() to improve code
readability.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260410152022.2146488-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The minimum baud rate supported by this driver is 0, so even for the B0
case, uart_get_baud_rate() will return 9600, not zero. This check predates
commit 16ae2a877b ("serial: Fix crash if the minimum rate of the device
is > 9600 baud") and is no longer necessary so remove it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260410152022.2146488-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The minimum baud rate supported by this driver is 300, so even for the B0
case, uart_get_baud_rate() will return 9600, not zero. This check predates
commit 16ae2a877b ("serial: Fix crash if the minimum rate of the device
is > 9600 baud") and is no longer necessary so remove it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260410152022.2146488-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UltraRISC DP1000 UART does not provide the standard CPR register used
by 8250_dw to discover port capabilities.
Provide a fixed CPR value for the DP1000-specific compatible so the
driver can configure the port correctly.
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260429-ultrarisc-serial-v7-4-e475cce9e274@ultrarisc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UltraRISC DP1000 integrates a Synopsys DesignWare APB UART, but it does
not provide the standard CPR and UCV registers.
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260429-ultrarisc-serial-v7-3-e475cce9e274@ultrarisc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the magic CPR value for Renesas RZ/N1 with a composition using
DW_UART_CPR_* bit/field definitions and FIELD_PREP_CONST().
Introduce a helper macro to convert a FIFO size (bytes) into the CPR
FIFO_MODE field value, with BUILD_BUG_ON_ZERO() checks for alignment and
bounds. Use it to replace the literal FIFO_MODE values in the RZN1.
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260429-ultrarisc-serial-v7-2-e475cce9e274@ultrarisc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the DW_UART_* register offsets and CPR bit/field definitions from
8250_dwlib.c into 8250_dwlib.h so they can be shared by 8250_dw and
8250_dwlib users.
Add an include guard for 8250_dwlib.h.
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260429-ultrarisc-serial-v7-1-e475cce9e274@ultrarisc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than using the UPF_CONS_FLOW bit of uart_port.flags to track
the user configuration of console flow control, use the newly added
uart_port.cons_flow (via its getter/setter functions).
A coccinelle script was used to perform the search/replace.
Note1: The sh-sci driver is blindly copying platform data configuration
flags to uart_port.flags. Thus UPF_CONS_FLOW could get set for
uart_port.flags. A follow-up commit will address this.
Note2: The samsung_tty driver is using UPF_CONS_FLOW as a platform data
configuration flag. However, the driver explicitly checks for
this configuration flag and thus setting UPF_CONS_FLOW in
uart_port.flags is avoided.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260506121606.5805-3-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the UPF_CONS_FLOW bit in the uart_port.flags field is used
by serial console drivers to identify if a user has configured flow
control on the console. Usually this policy is setup during early
boot, but can be changed at runtime.
The bits in uart_port.flags are either hardware and driver
properties that are initialized before usage or are properties that
can be changed via the tty layer.
The UPF_CONS_FLOW bit is an exception because it is a console-only
policy that can change at runtime and its setting and usage have
nothing to do with the tty layer. This actually causes a problem
for its usage because uart_port.flags is synchronized by a related
tty_port.mutex, but a console has no relation to a tty (other than
sharing the port).
This is probably why console flow control is not properly available
for most serial drivers. And it is hindering being able to provide a
proper implementation. Commit d01f4d181c ("serial: core: Privatize
tty->hw_stopped") addressed a similar issue to deal with software
assisted CTS flow state tracking.
Add a new uart_port boolean field "cons_flow" to store the user
configuration for console flow control. Add getter/setter wrappers
to allow for adding more policies later and/or locking constraint
validation.
Mark UPF_CONS_FLOW as deprecated.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260506121606.5805-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver doesn't use the driver_data field, so drop the assigment
together with the then redundant zero assigment for .class and
.class_mask. Also drop the zero in the list terminator.
While at it also use PCI_VDEVICE() to allow dropping "PCI_VENDOR_ID_".
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260505084749.2304121-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... and PCI device helpers.
The various struct pci_device_id were defined using a mixture of
initialization by position and by name. Some use the PCI device helpers
(like PCI_DEVICE and PCI_DEVICE_SUB) and others don't.
Consistently use named initializers, drop assignments of 0 by position
for .class and .class_mask and use the PCI device helpers. Also use
consistent line-breaks and positioning for opening and closing curly
braces.
The secret plan is to make struct pci_device_id::driver_data an
anonymous union (similar to
https://lore.kernel.org/all/cover.1776579304.git.u.kleine-koenig@baylibre.com/)
and that requires named initializers. But it's also a nice cleanup on
its own.
This patch doesn't change the compiled result; this was verified using
an allmodconfig with several things disabled that make reproducible
builds harder on x86 and arm64.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260428144033.1037617-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The synclink_gt driver was marked as broken in commit 426263d5fb
("tty: synclink_gt: mark as BROKEN") in July 2023 because it had severe
structural problems and there had been no evidence of users since 2016.
Since then, no meaningful improvements have been made to the driver,
and it is unlikely that will ever happen due to the lack of interest.
Drop the driver and references to it in comments and documentation.
include/uapi/linux/synclink.h is also removed. The only use of this
header I have found is the linux-raw-sys Rust crate. It generates
bindings for all UAPI headers, but has a hardcoded list of headers and
ioctls, including this one, so that does not indicate that anyone is
using it. I have sent a pull request to remove the include and ioctl
definitions for this header (see the link below).
Link: https://github.com/sunfishcode/linux-raw-sys/pull/185
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20260504031519.18877-1-enelsonmoore@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My MIPS Alchemy systems generate the following warning during
probe of the 8250 driver:
WARNING: drivers/tty/serial/8250/8250_port.c:462 at set_io_from_upio+0xfc/0x124, CPU#0: swapper/0/1
Unsupported UART type 4
[...]
[<80521d40>] set_io_from_upio+0xfc/0x124
[<80521dfc>] serial8250_set_defaults+0x94/0xe0
[<80520fb4>] serial8250_register_8250_port+0x288/0x51c
[<805214ec>] serial8250_probe+0x160/0x1e8
[<8053b5f0>] platform_probe+0x64/0x90
The least invasive fix is to recognize UPIO_AU (type 4) in set_io_from_upio()
and do nothing, since all parameters have already been set up in
8250_rt288x.c::au_platform_setup().
Run-tested on Alchemy Au1300 platform.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Link: https://patch.msgid.link/20260430135822.905035-1-manuel.lauss@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO_LINE_DIRECTION_* definitions have just recently been exposed to
gpio consumers.h by breaking them out in a separate defs.h file.
Use this to validate the gpio direction instead of the hard-coded literal.
Signed-off-by: Nikola Z. Ivanov <zlatistiv@gmail.com>
Link: https://patch.msgid.link/20260426214250.781151-1-zlatistiv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI support to 8250_mtk driver. This makes it possible to
use UART on ARM-based desktops with EDK2 UEFI firmware.
Signed-off-by: Yenchia Chen <yenchia.chen@mediatek.com>
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://patch.msgid.link/20260423062345.2473300-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various names for Qualcomm as a company are used in user-visible config
options: QCOM, Qualcomm and Qualcomm Technologies. Switch to unified
"Qualcomm" so it will be easier for users to identify the options when
for example running menuconfig.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260427070052.18097-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Raspberry Pi 3B by marking the VEC clk critical so it doesn't get
turned off and hang the bus.
-----BEGIN PGP SIGNATURE-----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=JtUn
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the merge window to avoid a boot hang on
Raspberry Pi 3B by marking the VEC clk critical so that it
doesn't get turned off and hang the bus"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: bcm: rpi: Mark VEC clock as CLK_IGNORE_UNUSED
- Drop class_create() for the "tsm" class
-----BEGIN PGP SIGNATURE-----
iIYEABYKAC4WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCae40aBAcZGpid0BrZXJu
ZWwub3JnAAoJEN+KhhkeUWxn/F0BAIpdhnq3TbPMC6Pj0q3DfcXpP+LPD0pqqIom
TwsQVZJCAP4rYVEbIbgeXvkilr7Fpcs2AXbidR/ggBsR3lyVBSNhAA==
=ZK/r
-----END PGP SIGNATURE-----
Merge tag 'tsm-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm
Pull PCIe TSP update from Dan Williams:
"A small update for the TSM core. It is arguably a fix and coming in
late as I have been offline the past few weeks:
- Drop class_create() for the 'tsm' class"
* tag 'tsm-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm:
virt: coco: change tsm_class to a const struct
- kbuild: builddeb - avoid recompiles for non-cross-compiles
Avoid triggering complete rebuilds for non-cross-compile Debian
package builds by only triggering the rebuild of host tools for
actual cross-compile builds.
- kbuild: Never respect CONFIG_WERROR / W=e to fixdep
Avoid spurious rebuilds of fixdep w/ and w/o -Werror during a single
kbuild invocation by never respecting CONFIG_WERROR for fixdep.
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Mathias Krause <minipli@grsecurity.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Thomas Weißschuh <linux@weissschuh.net>
-----BEGIN PGP SIGNATURE-----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=yCeR
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nicolas Schier:
- builddeb - avoid recompiles for non-cross-compiles
Avoid triggering complete rebuilds for non-cross-compile Debian
package builds by only triggering the rebuild of host tools for
actual cross-compile builds
- Never respect CONFIG_WERROR / W=e to fixdep
Avoid spurious rebuilds of fixdep w/ and w/o -Werror during a single
kbuild invocation by never respecting CONFIG_WERROR for fixdep
* tag 'kbuild-fixes-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Never respect CONFIG_WERROR / W=e to fixdep
kbuild: builddeb - avoid recompiles for non-cross-compiles
Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode
-----BEGIN PGP SIGNATURE-----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=mY/t
-----END PGP SIGNATURE-----
Merge tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode"
* tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: abx80x: Disable alarm feature if no interrupt attached
rtc: ntxec: fix OF node reference imbalance
rtc: pic32: allow driver to be compiled with COMPILE_TEST
rtc: ti-k3: Add support to resume from IO DDR low power mode
rtc: cmos: Use platform_get_irq_optional() in cmos_platform_probe()
dt-bindings: rtc: add olpc,xo1-rtc to trivial-rtc
dt-bindings: rtc: sc2731: Add compatible for SC2730
rtc: add data_race() in rtc_dev_poll()
rtc: armada38x: zalloc + calloc to single allocation
dt-bindings: rtc: isl12026: convert to YAML schema
dt-bindings: rtc: microcrystal,rv3028: Allow to specify vdd-supply
rtc: max77686: convert to i2c_new_ancillary_device
dt-bindings: rtc: mpfs-rtc: permit resets
rtc: rx8025: Remove use of i2c_match_id()
rtc: rv8803: Remove use of i2c_match_id()
rtc: rs5c372: Remove use of i2c_match_id()
rtc: pcf2127: Remove use of i2c_match_id()
rtc: m41t80: Remove use of i2c_match_id()
rtc: abx80x: Remove use of i2c_match_id()
mentioning separately: Rafael's commit converting tpm_crb from ACPI driver
to a platform driver. Starting from this release cycle, the branch with TPM
changes mirrored to next is 'for-next-tpm', and patches for keys have their
own separate 'for-next-keys' branch.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRE6pSOnaBC00OEHEIaerohdGur0gUCaezVbgAKCRAaerohdGur
0ggHAQDmhaZ2C3ddAV1WjfXh1YqdWAmqEqoP7ZHAh4OrjyRPTQD+Pc4xl9TSOgHx
/9WzzV6AM6fL5RuC2/PO5RvOKF9mswc=
=tpJM
-----END PGP SIGNATURE-----
Merge tag 'for-next-tpm-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
"Here are the accumulated fixes for 7.1-rc1 and a single structural
change worth mentioning separately: Rafael's commit converting tpm_crb
from ACPI driver to a platform driver"
* tag 'for-next-tpm-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: tpm_tis: stop transmit if retries are exhausted
tpm: tpm_tis: add error logging for data transfer
tpm: avoid -Wunused-but-set-variable
tpm: Use kfree_sensitive() to free auth session in tpm_dev_release()
tpm2-sessions: Fix missing tpm_buf_destroy() in tpm2_read_public()
tpm: Fix auth session leak in tpm2_get_random() error path
tpm: i2c: atmel: fix block comment formatting
tpm_crb: Convert ACPI driver to a platform one
tpm: Make tcpci_pm_ops variable static const
Since v2025.11.22:
Initial SoC Slider support
SoC Slider is an SoC-wide power/performance policy setting.
On SoC Slider systems, EPP plays a diminished role.
Whitespace cleanup via: indent -npro -kr -i8 -ts8 -sob -l160 -ss -ncs -cp1
No functional changes
Signed-off-by: Len Brown <len.brown@intel.com>
x86_energy_perf_policy accesses the SoC Slider via standard
user/kernel APIs to the processor_thermal_soc_slider driver.
Machines that support SoC Slider largely use it instead of EPP,
which may continue to exist in a diminished role, or vanish entirely.
Signed-off-by: Len Brown <len.brown@intel.com>
When processor_thermal_soc_slider is loaded, its slider
and offset modparams are visible. Check that the driver
actually registered the profile named "SoC Slider" before
reading or writing these modparams.
n.b. This utility allows writing the Slider and Offset modparams
even if the driver policy is not "balanced". Currently the
processor_thermal_soc_slider consults those modparams
only in "balanced" mode.
Signed-off-by: Len Brown <len.brown@intel.com>
On Raspberry Pi 3B, the VEC clock is used by the VideoCore firmware
display driver, which remains active until the vc4 driver loads and
sends NOTIFY_DISPLAY_DONE. If this clock is disabled during boot, a bus
lockup happens and the firmware becomes unresponsive, causing a complete
system lockup.
Mark the VEC clock with CLK_IGNORE_UNUSED so it survives the unused
clock disablement and remains available until the vc4 driver takes over
display management.
Fixes: 672299736a ("clk: bcm: rpi: Manage clock rate in prepare/unprepare callbacks")
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/r/5f0bec08-f458-4fba-8bf3-06817a100c4c@sirena.org.uk
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patch.msgid.link/20260401111416.562279-2-mcanal@igalia.com
Tested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Brian Masney <bmasney@redhat.com> # Active contributor to clk
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
