Packets ingressing on a LAG that egress on the CPU port, which are not
classified as management, will have a FORWARD tag that does not
contain the normal source device/port tuple. Instead the trunk bit
will be set, and the port field holds the LAG id.
Since the exact source port information is not available in the tag,
frames are injected directly on the LAG interface and thus do never
pass through any DSA port interface on ingress.
Management frames (TO_CPU) are not affected and will pass through the
DSA port interface as usual.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support offloading of LAGs to hardware. LAGs may be attached to a
bridge in which case VLANs, multicast groups, etc. are also offloaded
as usual.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Monitor the following events and notify the driver when:
- A DSA port joins/leaves a LAG.
- A LAG, made up of DSA ports, joins/leaves a bridge.
- A DSA port in a LAG is enabled/disabled (enabled meaning
"distributing" in 802.3ad LACP terms).
When a LAG joins a bridge, the DSA subsystem will treat that as each
individual port joining the bridge. The driver may look at the port's
LAG device pointer to see if it is associated with any LAG, if that is
required. This is analogue to how switchdev events are replicated out
to all lower devices when reaching e.g. a LAG.
Drivers can optionally request that DSA maintain a linear mapping from
a LAG ID to the corresponding netdev by setting ds->num_lag_ids to the
desired size.
In the event that the hardware is not capable of offloading a
particular LAG for any reason (the typical case being use of exotic
modes like broadcast), DSA will take a hands-off approach, allowing
the LAG to be formed as a pure software construct. This is reported
back through the extended ACK, but is otherwise transparent to the
user.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a situation where a standalone port is indirectly attached to a
bridge (e.g. via a LAG) which is not offloaded, do not offload any
port attributes either. The port should behave as a standard NIC.
Previously, on mv88e6xxx, this meant that in the following setup:
br0
/
team0
/ \
swp0 swp1
If vlan filtering was enabled on br0, swp0's and swp1's QMode was set
to "secure". This caused all untagged packets to be dropped, as their
default VID (0) was not loaded into the VTU.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When creating a static bond (e.g. balance-xor), all ports will always
be enabled. This is set, and the corresponding notification is sent
out, before the port is linked to the bond upper.
In the offloaded case, this ordering is hard to deal with.
The lower will first see a notification that it can not associate with
any bond. Then the bond is joined. After that point no more
notifications are sent, so all ports remain disabled.
This change simply sends an extra notification once the port has been
linked to the upper to synchronize the initial state.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
prestera_bridge_port_vlan_add should have been called with vlan->vid,
however this was masked by the presence of the local vid variable and I
did not notice the build warning.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Taras Chornyi <tchornyi@marvell.com>
Link: https://lore.kernel.org/r/20210114083556.2274440-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As requested by upstream OVS, added some error messages in the
validate_and_copy_dec_ttl function.
Includes a small cleanup, which removes an unnecessary parameter
from the dec_ttl_exception_handler() function.
Reported-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Link: https://lore.kernel.org/r/161054576573.26637.18396634650212670580.stgit@ebuild
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Ahern says:
====================
selftests: Updates to allow single instance of nettest for client and server
Update nettest to handle namespace change internally to allow a
single instance to run both client and server modes. Device validation
needs to be moved after the namespace change and a few run time
options need to be split to allow values for client and server.
v4
- really fix the memory leak with stdout/stderr buffers
v3
- send proper status in do_server for UDP sockets
- fix memory leak with stdout/stderr buffers
- new patch with separate option for address binding
- new patch to remove unnecessary newline
v2
- fix checkpath warnings
====================
Link: https://lore.kernel.org/r/20210114030949.54425-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add separate option to nettest to specify local address
binding in client mode.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new options to nettest to specify device binding and expected
device binding for server mode, and update fcnal-test script. This
is needed to allow a single instance of nettest running both server
and client modes to use different device bindings.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new option to nettest to specify MD5 password to use for client
side. Update fcnal-test script. This is needed for a single instance
running both server and client modes to test password mismatches.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nettest started with -r as the remote address for MD5 passwords.
The -m argument was added to use prefixes with a length when that
feature was added to the kernel. Since -r is used to specify
remote address for client mode, change nettest to only use -m
for MD5 passwords and update fcnal-test script.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a single instance of nettest is used for client and server
make sure address validation is only done for client mode.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A few logging lines are missing the newline, or need it moved up for
cleaner logging.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a single instance of nettest is doing both client and
server modes, stdout and stderr messages can get interlaced
and become unreadable. Allocate a new set of buffers for the
child process handling server mode.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add option to nettest to run both client and server within a
single instance. Client forks a child process to run the server
code. A pipe is used for the server to tell the client it has
initialized and is ready or had an error. This avoid unnecessary
sleeps to handle such race when the commands are separately launched.
Signed-off-by: Seth David Schoen <schoen@loyalty.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add options to specify server and client network namespace to
use before running respective functions.
Signed-off-by: Seth David Schoen <schoen@loyalty.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPv6 addresses can have a device name to declare a scope (e.g.,
fe80::5054:ff:fe12:3456%eth0). The next patch adds support to
switch network namespace before running client or server code
(or both), so move the address validation to the server and
client functions.
IPv4 multicast groups do not have the device scope in the address
specification, so they can be validated inline with option parsing.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
convert_addr needs to be invoked in a different location. Move
the code up to avoid a forward declaration.
Code move only.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Later patch adds support for switching network namespaces before
running client, server or both. Device validations need to be
done after the network namespace switch, so add a helper to do it
and invoke in server and client code versus inline with argument
parsing. Move related argument checks as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjarni Jonasson says:
====================
Add 100 base-x mode
Adding support for 100 base-x in phylink.
The Sparx5 switch supports 100 base-x pcs (IEEE 802.3 Clause 24) 4b5b encoded.
These patches adds phylink support for that mode.
Tested in Sparx5, using sfp modules:
Axcen 100fx AXFE-1314-0521 (base-fx)
Axcen 100lx AXFE-1314-0551 (base-lx)
HP SFP 100FX J9054C (bx-10)
Excom SFP-SX-M1002 (base-lx)
v1 -> v2:
Added description to Documentation/networking/phy.rst
Moved PHY_INTERFACE_MODE_100BASEX to above 1000BASEX
Patching against net-next
====================
Link: https://lore.kernel.org/r/20210113115626.17381-1-bjarni.jonasson@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for 100Base-FX, 100Base-LX, 100Base-PX and 100Base-BX10 modules
This is needed for Sparx-5 switch.
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sparx-5 supports this mode and it is missing in the PHY core.
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bit is enabled by default and advertises support for extended
next page support. XNP is only needed for 10GBase-T and MultiGig
support which is not supported. Additionally, Cisco MultiGig switches
will read this bit and attempt 10Gb negotiation even though Next Page
support is disabled. This will cause timeouts when the interface is
forced to 100Mbps and auto-negotiation will fail. The interfaces are
only 1000Base-T and supporting auto-negotiation for this only requires
the Next Page bit to be set.
Taken from:
7406c5244b
and adapted to mainline kernels by rmk.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kzSdb-000417-FJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move skb_set_hash_from_sk s.t. it's called after instead of before
tcp_event_data_sent is called. This enables congestion control
modules to change the socket hash right before restarting from
idle (via the TX_START congestion event).
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20210111230552.2704579-1-ycheng@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check if the interface is indeed connected to a MAC before trying to
close the DPMAC object representing it. Without this check we end up
working with a NULL pointer.
Fixes: d87e606373 ("dpaa2-mac: export MAC counters even when in TYPE_FIXED")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210111171802.1826324-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Declare Rx VLAN filtering as supported and user-changeable only when
there are VLAN filtering entries available on the DPNI object. Even
then, rx-vlan-filtering is by default disabled.
Also, populate the .ndo_vlan_rx_add_vid() and .ndo_vlan_rx_kill_vid()
callbacks for adding and removing a specific VLAN from the VLAN table.
Signed-off-by: Ionut-robert Aron <ionut-robert.aron@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210111170725.1818218-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support to install flow rules using ipv4 proto or
ipv6 next header field to distinguish between tcp/udp/sctp/esp/ah
flows when user doesn't specify the other match creteria related to
the flow such as tcp/udp/sctp source port and destination port, ah/esp
spi value. This is achieved by matching the layer type extracted by
NPC HW into the search key. Modified the driver to use Ethertype as
match criteria when user doesn't specify source IP address and dest
IP address. The esp/ah flow rule matching using security parameter
index (spi) is not supported as of now since the field is not extracted
into MCAM search key. Modified npc_check_field function to return bool.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20210111112537.3277-1-naveenm@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5 updates 2021-01-07
Misc updates series for mlx5 driver:
1) From Eli and Jianbo, E-Switch cleanups and usage of new
FW capability for mpls over udp
2) Paul Blakey, Adds support for mirroring with Connection tracking
by splitting rules to pre and post Connection tracking to perform the
mirroring.
3) Roi Dayan, cleanups for connection tracking
4) From Tariq, Cleanups and improvements to IPSec
====================
Link: https://lore.kernel.org/r/20210112070534.136841-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MLX5_IPSEC_DEV() is always defined, no need to protect it under config
flag CONFIG_MLX5_EN_IPSEC, especially in slow path.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Feature check functions are in the TX fast-path of all SKBs, not only
IPsec traffic.
Move the IPsec feature check function into a header and turn it inline.
Use a stub and clean the config flag condition in Eth main driver file.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All IPsec logic should be wrapped under the compile flag,
including its checksum logic.
Introduce an inline function in ipsec datapath header,
with a corresponding stub.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The zone member is of type u16 so there is no reason to apply
the zone mask on it. This is also matching the call to set a
match in other places which don't need and don't apply the mask.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
miss_rule and prio_s args are not being referenced before assigned
so there is no need to init them.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No need to pass zero spec to mlx5_add_flow_rules() as the
function can handle null spec.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Miss path handling of tc multi chain filters (i.e. filters that are
defined on chain > 0) requires the hardware to communicate to the
driver the last chain that was processed. This is possible only when
the hardware is capable of performing the combination of modify header
and forward to table actions. Currently, if the hardware is missing
this capability then the driver only offloads rules that are defined
on tc chain 0 prio 1. However, this restriction can be relaxed because
packets that miss from chain 0 are processed through all the
priorities by tc software.
Allow the offload of all the supported priorities for chain 0 even
when the hardware is not capable to perform modify header and goto
table actions.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use tunnel_stateless_mpls_over_udp instead of
MLX5_FLEX_PROTO_CW_MPLS_UDP since new devices have native support for
mpls over udp and do not rely on flex parser.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
esw->qos.enabled will only be true if both MLX5_CAP_GEN(dev, qos) and
MLX5_CAP_QOS(dev, esw_scheduling) are true. Therefore, remove them from
the condition in and rely only on esw->qos.enabled.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add capability bit to test whether reg_c value is preserved on
recirculation.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oleksij Rempel says:
====================
net: dsa: add stats64 support
changes v8:
- stats.no_handler should not be assigned from HW stats
changes v7:
- move raw.filtered from rx_errors to rx_dropped counter
changes v6:
- move stats64 callback to ethtool section
- ar9331: diff. fixes
- ar9331: move stats calculation to the worker
- ar9331: extend rx/tx error counters
- use spin lock instead of u64_stats*
changes v5:
- read all stats in one regmap_bulk_read() request
- protect stats with u64_stats* helpers.
changes v4:
- do no read MIBs withing stats64 call
- change polling frequency to 0.3Hz
changes v3:
- fix wrong multiplication
- cancel port workers on remove
changes v2:
- use stats64 instead of get_ethtool_stats
- add worked to poll for the stats
====================
Link: https://lore.kernel.org/r/20210111104658.21930-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA driver depends on some SMEM functionality (qcom_smem_init(),
qcom_smem_alloc(), and qcom_smem_virt_to_phys()), but this is not
reflected in the configuration dependencies. Add a dependency on
QCOM_SMEM to avoid attempts to build the IPA driver without SMEM.
This avoids a link error for certain configurations.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 38a4066f59 ("net: ipa: support COMPILE_TEST")
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210112192134.493-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add debugfs support to SFP so that the internal state of the SFP state
machines and hardware signal state can be viewed from userspace, rather
than having to compile a debug kernel to view state transitions in the
kernel log. The 'state' output looks like:
Module state: empty
Module probe attempts: 0 0
Device state: up
Main state: down
Fault recovery remaining retries: 5
PHY probe remaining retries: 12
moddef0: 0
rx_los: 1
tx_fault: 1
tx_disable: 1
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1kyYRe-0004kN-3F@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
