A small set of updates that came in during the merge window, we've got:
- Some small fixes for the Broadcom and spi-pci1xxxx drivers
- A change to the QPIC SNAND driver to flag that the error correction
features are less useful than people might be expecting.
- A new device ID for the SOPHGO SG2042.
- The addition of Yang Shen as a Huawei maintainer.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmhBmMAACgkQJNaLcl1U
h9BvAwf/dkfLLmAUNPhex0hQaj8aKbiN3NWMRbZPApPAdy+s9u3d6zW1BlZI6liK
97PEgxQ1d60lxwKdPiYjhLuJTDGeEDSsGTUI5OXqz2hW08mfYQaRN96xZKwJf67G
8y8u3rEZLbDs0vKorf3TG8KHTj1lBbfl9GwwzEFQlMUNdEDXnBadd+C08PMwIhdR
PYJrARKV3aZ4GhaQwF6JsvLV2JomQ/ALES4RaW8hDgDdzjiqda0fKV0YWDZwa8E1
08Pea9uUr78iAoohqO6rCQBqWCFms8HEpgz2NerY2CGMhrjnA64XTfSyRNp9q2O5
gllrngHhluRPl2vM3JuO3fdiVk+xmA==
=dFS2
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.16-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull more spi updates from Mark Brown:
"A small set of updates that came in during the merge window, we've
got:
- Some small fixes for the Broadcom and spi-pci1xxxx drivers
- A change to the QPIC SNAND driver to flag that the error correction
features are less useful than people might be expecting
- A new device ID for the SOPHGO SG2042
- The addition of Yang Shen as a Huawei maintainer"
* tag 'spi-v6.16-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-qpic-snand: document the limited bit error reporting capability
spi: bcm63xx-hsspi: fix shared reset
spi: bcm63xx-spi: fix shared reset
MAINTAINERS: Update HiSilicon SFC driver maintainer
MAINTAINERS: Update HiSilicon SPI Controller driver maintainer
spi: dt-bindings: spi-sg2044-nor: Add SOPHGO SG2042
spi: spi-pci1xxxx: Fix Probe failure with Dual SPI instance with INTx interrupts
register a master device. This is a problem that has been there forever:
the "master" device was not always present depending on a number of
heuristics such as the presence of fixed partitions and the absence of a
Kconfig symbol to force its presence. This was a problem for runtime PM
operations which might not have the "master" device available in all
situation.
The SPI NAND subsystem has seen the introduction of DTR operations (the
equivalent of DDR transfers), which involved quite a few preparation
patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for old
legacy SoCs with an update of the ->exec_op() hook, there has been the
introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Finally, Macornix SPI NOR entries have been cleaned-up and some SFDP
table fixups for Macronix MX25L3255E have been merged.
Aside from this, there is the usual load of misc improvement, fixes,
and yaml conversion.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmg91NEACgkQJWrqGEe9
VoR8egf+JPTtykQ+Bip9bHStgfpxi0+OKL81PUuPBsbs5C546u5t6ZRhoPsU+KqL
ZTyUk3ys7HcSwZCuiS9V6ea6TNV1FvAVZm+ONpkuPnU60++z8YfVr8ZvtgT0IUXx
COi+5ksdsTFZMyRG+VybRKnYNrTYB7j7CqVL8ifxq1XYWnYdhjy5PH4DgAKnBhGL
523kN2eR85AhvJ4aulsKbcqQQYKvJIQbhjAKklA3yQVarDmoOdiSmndoZlRy+MDu
B9DaRMvRRa/g1nI0stvR9K7FtdSrMYTg4kowR9jPRx0zEZXFFsZbASgcC+3G7HdK
7rLFWrN+G6fitcEjeAnfyV+sKF48LA==
=tW1t
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"A big core MTD change is the introduction of a new class to always
register a master device. This is a problem that has been there
forever: the "master" device was not always present depending on a
number of heuristics such as the presence of fixed partitions and the
absence of a Kconfig symbol to force its presence. This was a problem
for runtime PM operations which might not have the "master" device
available in all situation.
The SPI NAND subsystem has seen the introduction of DTR operations
(the equivalent of DDR transfers), which involved quite a few
preparation patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for
old legacy SoCs with an update of the ->exec_op() hook, there has been
the introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Finally, Macornix SPI NOR entries have been cleaned-up and some SFDP
table fixups for Macronix MX25L3255E have been merged.
Aside from this, there is the usual load of misc improvement, fixes,
and yaml conversion"
* tag 'mtd/for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (42 commits)
mtd: rawnand: brcmnand: legacy exec_op implementation
mtd: rawnand: sunxi: Add randomizer configuration in sunxi_nfc_hw_ecc_write_chunk
mtd: nand: brcmnand: fix NAND timeout when accessing eMMC
mtd: nand: sunxi: Add randomizer configuration before randomizer enable
mtd: spinand: esmt: fix id code for F50D1G41LB
mtd: rawnand: brcmnand: remove unused parameters
mtd: core: always create master device
mtd: rawnand: loongson1: Fix inconsistent refcounting in ls1x_nand_chip_init()
mtd: rawnand: loongson1: Fix error code in ls1x_nand_dma_transfer()
mtd: rawnand: qcom: Fix read len for onfi param page
mtd: rawnand: qcom: Fix last codeword read in qcom_param_page_type_exec()
mtd: rawnand: qcom: Pass 18 bit offset from NANDc base to BAM base
dt-bindings: mtd: qcom,nandc: Document the SDX75 NAND controller
mtd: bcm47xxnflash: Add error handling for bcm47xxnflash_ops_bcm4706_ctl_cmd()
mtd: rawnand: Use non-hybrid PCI devres API
mtd: nand: ecc-mxic: Fix use of uninitialized variable ret
mtd: spinand: winbond: Add support for W35N02JW and W35N04JW chips
mtd: spinand: winbond: Add octal support
mtd: spinand: winbond: Add support for W35N01JW in single mode
mtd: spinand: winbond: Rename DTR variants
...
The QPIC hardware is not capable of reporting the exact number of the
corrected bit errors, it only reports the number of the corrected bytes.
Document this behaviour in the code, and also issue a warning message
to inform the user about it.
No functional changes.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250527-qpic-snand-limited-biterr-caps-v1-1-61f7cf87be1e@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some bmips SoCs (bcm6362, bcm63268) share the same SPI reset for both SPI
and HSSPI controllers, so reset shouldn't be exclusive.
Fixes: 0eeadddbf0 ("spi: bcm63xx-hsspi: add reset support")
Reported-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250529130915.2519590-3-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some bmips SoCs (bcm6362, bcm63268) share the same SPI reset for both SPI
and HSSPI controllers, so reset shouldn't be exclusive.
Fixes: 38807adeaf ("spi: bcm63xx-spi: add reset support")
Reported-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250529130915.2519590-2-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This bulk of the changes in this release are driver work, as well as
new device support we have some important work on performance over
several drivers, and big overhauls for maintainability on a couple too.
Highlights include:
- Big cleanups of the sh-msiof driver from Geert Uytterhoeven, and of
the NXP FSPI driver from Haibo Chen.
- Performance improvements for the AXI SPI engine.
- Support for writes to memory mapped flashes on Renesas devices.
- Integrated DMA support for Tegra210 QSPI, used by the Tegra234.
- DMA support for Amlogic SPI controllers.
- Support for AMD HID2, Qualcomm IPQ5018, Renesas RZ/G3E, Rockchip
RK3528 and Samsung Exynos Autov920.
An update to fix some issues with the Atmel QSPI driver runtime PM
pulled in a new API from the PM core, and the Renesas memory mapped
write changes pull in some code that's shared in drivers/memory.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmgzCzkACgkQJNaLcl1U
h9DF5gf+MlaB2j6ggH/OnXdV6aQTcjta357+ptWH3CDQbx0nsMj50i+eqxhzOK69
tyOMX0gcqo8bBQq1mhm3Z2fDYbYYRKwf7OwymHD1KGNGn9zegORNw790/XGTeoMo
m5f9Trz9UNP+7NjWuOioKoy6zghp4Ti2WAAUPhGUQBnyaV269bonNvisRtqnDP5u
nOu1DYANZqL3icuUIdJ3Aklmn4On1svUPuE9HOn/GNocZZWegcCHfBjmSRuLUAGO
RR1jP/d+RfSvTSrdqZGwrfWLFBBirjSLXNB1g7sjiVTnSseuBnOZ/z7PuBQQ+NuB
ENyoQXNLFZKMTQ5wmuQpXnwIIXsxYg==
=FmJ2
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The bulk of the changes in this release are driver work, as well as
new device support we have some important work on performance over
several drivers, and big overhauls for maintainability on a couple
too. Highlights include:
- Big cleanups of the sh-msiof driver from Geert Uytterhoeven, and of
the NXP FSPI driver from Haibo Chen
- Performance improvements for the AXI SPI engine
- Support for writes to memory mapped flashes on Renesas devices
- Integrated DMA support for Tegra210 QSPI, used by the Tegra234
- DMA support for Amlogic SPI controllers
- Support for AMD HID2, Qualcomm IPQ5018, Renesas RZ/G3E, Rockchip
RK3528 and Samsung Exynos Autov920
An update to fix some issues with the Atmel QSPI driver runtime PM
pulled in a new API from the PM core, and the Renesas memory mapped
write changes pull in some code that's shared in drivers/memory"
* tag 'spi-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: spi-qpic-snand: return early on error from qcom_spi_io_op()
spi: loopback-test: fix up const pointer issue in rx_ranges_cmp()
spi: gpio: fix const issue in spi_to_spi_gpio()
spi: spi-qpic-snand: remove superfluous parameters of qcom_spi_check_error()
dt-bindings: spi: samsung: add exynosautov920-spi compatible
spi: spi-qpic-snand: reuse qcom_spi_check_raw_flash_errors()
spi: dt-bindings: Add rk3528-spi compatible
spi: spi_amd: Update Kconfig dependencies
spi: spi_amd: Add HIDDMA basic write support
spi: spi_amd: Remove read{q,b} usage on DMA buffer
spi: sh-msiof: Move register definitions to <linux/spi/sh_msiof.h>
spi: sh-msiof: Document frame start sync pulse mode
spi: sh-msiof: Double maximum DMA transfer size using two groups
spi: sh-msiof: Simplify BRG's Division Ratio
spi: sh-msiof: Increase TX FIFO size for R-Car V4H/V4M
spi: sh-msiof: Correct RX FIFO size for R-Car Gen3
spi: sh-msiof: Correct RX FIFO size for R-Car Gen2
spi: sh-msiof: Add core support for dual-group transfers
spi: sh-msiof: Correct SIMDR2_GRPMASK
spi: sh-msiof: SIFCTR bitfield conversion
...
We've received a lot of activities in this cycle, mostly about leaf
driver codes rather than the core part, but with a good mixture of
code cleanups and new driver additions. Below are some highlights:
* ASoC:
- Support for automatically enumerating DAIs from standards conforming
SoundWire SDCA devices; not much used as of this writing, rather for
future implementations
- Conversion of quite a few drivers to newer GPIO APIs
- Continued cleanups and helper usages in allover places
- Support for a wider range of Intel AVS platforms
- Support for AMD ACP 7.x platforms, Cirrus Logic CS35L63 and CS48L32
Everest Semiconductor ES8375 and ES8389, Longsoon-1 AC'97
controllers, nVidia Tegra264, Richtek ALC203 and RT9123 and Rockchip
SAI controllers
* HD-audio:
- Lots of cleanups of TAS2781 codec drivers
- A new HD-audio control bound via ACPI for Nvidia
- Support for Tegra264, Intel WCL, usual new codec quirks
* USB-audio:
- Fix a race at removal of MIDI device
- Pioneer DJM-V10 support, Scarlett2 driver cleanups
* Misc:
- Cleanups of deprecated PCI functions
- Removal of unused / dead function codes
-----BEGIN PGP SIGNATURE-----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=ApEf
-----END PGP SIGNATURE-----
Merge tag 'sound-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've received a lot of activities in this cycle, mostly about leaf
driver codes rather than the core part, but with a good mixture of
code cleanups and new driver additions. Below are some highlights:
ASoC:
- Support for automatically enumerating DAIs from standards
conforming SoundWire SDCA devices; not much used as of this
writing, rather for future implementations
- Conversion of quite a few drivers to newer GPIO APIs
- Continued cleanups and helper usages in allover places
- Support for a wider range of Intel AVS platforms
- Support for AMD ACP 7.x platforms, Cirrus Logic CS35L63 and CS48L32
Everest Semiconductor ES8375 and ES8389, Longsoon-1 AC'97
controllers, nVidia Tegra264, Richtek ALC203 and RT9123 and
Rockchip SAI controllers
HD-audio:
- Lots of cleanups of TAS2781 codec drivers
- A new HD-audio control bound via ACPI for Nvidia
- Support for Tegra264, Intel WCL, usual new codec quirks
USB-audio:
- Fix a race at removal of MIDI device
- Pioneer DJM-V10 support, Scarlett2 driver cleanups
Misc:
- Cleanups of deprecated PCI functions
- Removal of unused / dead function codes"
* tag 'sound-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (364 commits)
firmware: cs_dsp: Fix OOB memory read access in KUnit test
ASoC: codecs: add support for ES8375
ASoC: dt-bindings: Add Everest ES8375 audio CODEC
ALSA: hda: acpi: Make driver's match data const static
ALSA: hda: acpi: Use SYSTEM_SLEEP_PM_OPS()
ALSA: atmel: Replace deprecated strcpy() with strscpy()
ALSA: core: fix up bus match const issues.
ASoC: wm_adsp: Make cirrus_dir const
ASoC: tegra: Tegra264 support in isomgr_bw
ASoC: tegra: AHUB: Add Tegra264 support
ASoC: tegra: ADX: Add Tegra264 support
ASoC: tegra: AMX: Add Tegra264 support
ASoC: tegra: I2S: Add Tegra264 support
ASoC: tegra: Update PLL rate for Tegra264
ASoC: tegra: ASRC: Update ARAM address
ASoC: tegra: ADMAIF: Add Tegra264 support
ASoC: tegra: CIF: Add Tegra264 support
dt-bindings: ASoC: Document Tegra264 APE support
dt-bindings: ASoC: admaif: Add missing properties
ASoC: dt-bindings: audio-graph-card2: reference audio-graph routing property
...
Fixes a probe failure that occurs when dual SPI controllers are
enabled and INTx interrupts are used. Reduces the minimum required
number of interrupt vectors to 1 and registers a shared ISR when
the allocated vectors are fewer than the number of controllers.
This change ensures that the probe succeeds even with limited
vectors, restoring INTx functionality when multiple SPI
controllers are present.
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Link: https://patch.msgid.link/20250527103244.26861-1-thangaraj.s@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Gabor Juhos <j4g8y7@gmail.com>:
The two patches in the series are extending the usage of FIELD_PREP()
macro and predefined bitmasks usage in the driver.
When submitting of the descriptors fails, it is quite likely that
the register read buffer contains no valid data. Even if the data
is valid the function returns with an error code anyway.
Change the code to return early if qcom_submit_descs() fails to
avoid superfluously copying possibly invalid data.
Also change the return statement at the end of the function to use
zero value to indicate success obviusly.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250515-qpic-snand-early-error-v1-1-681c87611213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If, in a previous transfer, the controller sends more data than expected
by the DSPI target, SR.RFDF (RX FIFO is not empty) will remain asserted.
When flushing the FIFOs at the beginning of a new transfer (writing 1
into MCR.CLR_TXF and MCR.CLR_RXF), SR.RFDF should also be cleared.
Otherwise, when running in target mode with DMA, if SR.RFDF remains
asserted, the DMA callback will be fired before the controller sends any
data.
Take this opportunity to reset all Status Register fields.
Fixes: 5ce3cc5674 ("spi: spi-fsl-dspi: Provide support for DSPI slave mode operation (Vybryd vf610)")
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://patch.msgid.link/20250522-james-nxp-spi-v2-3-bea884630cfb@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The XSPI mode implementation in this driver still uses the EOQ flag to
signal the last word in a transmission and deassert the PCS signal.
However, at speeds lower than ~200kHZ, the PCS signal seems to remain
asserted even when SR[EOQF] = 1 indicates the end of a transmission.
This is a problem for target devices which require the deassertation of
the PCS signal between transfers.
Hence, this commit 'forces' the deassertation of the PCS by stopping the
module through MCR[HALT] after completing a new transfer. According to
the reference manual, the module stops or transitions from the Running
state to the Stopped state after the current frame, when any one of the
following conditions exist:
- The value of SR[EOQF] = 1.
- The chip is in Debug mode and the value of MCR[FRZ] = 1.
- The value of MCR[HALT] = 1.
This shouldn't be done if the last transfer in the message has cs_change
set.
Fixes: ea93ed4c18 ("spi: spi-fsl-dspi: Use EOQ for last word in buffer even for XSPI mode")
Signed-off-by: Bogdan-Gabriel Roman <bogdan-gabriel.roman@nxp.com>
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://patch.msgid.link/20250522-james-nxp-spi-v2-2-bea884630cfb@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPI registers are NOT continuous, some registers are reserved and
accessing them from userspace will trigger external abort, add regmap
register access table to avoid below abort.
For example on S32G:
# cat /sys/kernel/debug/regmap/401d8000.spi/registers
Internal error: synchronous external abort: 96000210 1 PREEMPT SMP
...
Call trace:
regmap_mmio_read32le+0x24/0x48
regmap_mmio_read+0x48/0x70
_regmap_bus_reg_read+0x38/0x48
_regmap_read+0x68/0x1b0
regmap_read+0x50/0x78
regmap_read_debugfs+0x120/0x338
Fixes: 1acbdeb92c ("spi/fsl-dspi: Convert to use regmap and add big-endian support")
Co-developed-by: Xulin Sun <xulin.sun@windriver.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://patch.msgid.link/20250522-james-nxp-spi-v2-1-bea884630cfb@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When a list head is a const pointer, the list entry for that head also
must remain a const pointer, otherwise we are just "throwing it away"
for no good reason. Fix this up by properly marking these structures as
const.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2025052213-semifinal-sublevel-d631@gregkh
Signed-off-by: Mark Brown <broonie@kernel.org>
While the struct spi_device * passed into spi_to_spi_gpio() is a const
one, the struct spi_bitbang * that is retrieved from the controller
field in the spi_device is NOT a const pointer, as it is coming from the
spi_controller_get_devdata() call, and then passed to container_of()
which would strip off the const attribute for no good reason (i.e. if a
const pointer is passed to container_of() it still is const coming out).
Fix this all up by properly declaring the struct spi_bitbang * as not
const.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2025052225-scallion-ritzy-dbbd@gregkh
Signed-off-by: Mark Brown <broonie@kernel.org>
The qcom_spi_check_error() function determines the errors of a previous
page read operation solely by using the cached register values in the
register read buffer. The data pointed by the 'data_buf' and the 'oob_buf'
parameters are not used for that at all.
Remove the superfluous parameters of the function along with the related
local variables to simplify the code. Also, remove the variables from the
caller functions which became unused due to the change.
Note:
Althought the similar parse_read_errors() function in the 'qcom_nand'
driver has the same parameters, but that function passes down the
pointers to check_for_erased_page() at the end of the function.
It is not clear, that a similar call is missing here, or the superfluous
parameters are simply leftovers of the development process. Nevertheless,
if additional code is needed, the parameters can be added back later.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250520-qpic-snand-superfluous-params-v1-1-86dd4963e90f@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The qcom_spi_check_raw_flash_errors() function can be used to
verify the flash status after raw operations.
Move the function slightly up in the code and change the
qcom_spi_read_last_cw() function to call it instead of using
an open coded implementation of the same check.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250514-qpic-snand-error-check-v1-1-c0ebd3aae72a@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Geert Uytterhoeven <geert+renesas@glider.be>:
This patch series (A) improves single transfer sizes in the MSIOF
driver, using two methods:
- By increasing the assumed FIFO sizes, impacting both PIO and DMA
transfers,
- By using two groups, impacting DMA transfers,
and (B) lets the recently-introduced MSIOF I2S drive reuse the SPI
driver's register definitions. All of this is covered with a thick
sauce of fixes for (harmless) bugs, cleanups, and refactorings.
Note that the driver uses the limitations as specified in the hardware
documentation. For discovering the actual FIFO sizes, I wrote some
crude test code that can be found at [2].
This is based on spi/for-next and sound-asoc/for-next, and has been
tested on a variery of R-Car SoCs.
[1] https://lore.kernel.org/cover.1746180072.git.geert+renesas@glider.be
[2] https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git/log/?h=topic/msiof-fifo
Merge series from Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>:
This patchset adds support for sound card on Qualcomm QCS9100 and
QCS9075 boards.
Add X86 and SPI_MEM as dependencies for the spi_amd driver to ensure it is
built only on relevant platforms and with the required SPI memory
framework.
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250516100658.585654-4-Raju.Rangoju@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI index mode has hardware limitation of transferring only 64 bytes per
transaction due to fixed number of FIFO registers. This constraint leads to
performance issues when reading/writing data to/from NAND/NOR flash
devices, as the controller must issue multiple requests to read/write
64-byte chunks, even if the slave can transfer up to 2 or 4 KB in a single
transaction.
The AMD HID2 SPI controller supports DMA mode, allowing for reading/writing
up to 4 KB of data in a single transaction. The existing spi_amd driver
already supports HID2 DMA read operations.
This patch introduces changes to implement HID2 DMA single mode basic write
support for the HID2 SPI controller.
Co-developed-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Signed-off-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250516100658.585654-3-Raju.Rangoju@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add changes to replace the usage of read{q,b} MMIO accessors with direct
memory copy logic for reading data from DMA buffer.
Co-developed-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Signed-off-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250516100658.585654-2-Raju.Rangoju@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum DMA transfer size is limited by the maximum values that can
be written to the word count fields (WDLENx) in the Transmit and Control
Data Registers (SITDR2/SIRDR2). As all MSIOF variants support
transferring data of multiple (two or four) groups, the maximum size can
be doubled by using two groups instead of one, thus reducing setup
overhead for very large SPI transfers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/bad522c76b8d225c195433977b22f95015cf2612.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The MSIOF transmit FIFOs on R-Car V4H and V4M have 256 stages.
Add a new family-specific match entry to handle this.
Add quirk match entries for older R-Car Gen4 Socs (R-Car V3U and S4-8)
that have transmit FIFOs with only 64 stages, just like on R-Car Gen3.
Update the (unused) definition of SIFCTR_TFUA for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/69cb5fc48f034d37484fa127b9864a1971a83417.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.55 of
September 28, 2017, the MSIOF receive FIFOs on R-Car Gen3 SoCs have room
for 256 words of 32 bits.
Note that this change has no actual impact on the behavior of the
driver, as SPI_CONTROLLER_MUST_TX is set, and transfer size is currenty
limited to the minimum of the transmit and receive FIFO sizes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/6f74508ea4681aa0b7c6bf6810eab026725e75a3.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
According to Renesas Technical Updates TN-RCS-S068A/E, the MSIOF receive
FIFOs on R-Car Gen2 SoCs have room for 128 words of 32 bits.
Note that this change has no actual impact on the behavior of the
driver, as SPI_CONTROLLER_MUST_TX is set, and transfer size is currenty
limited to the minimum of the transmit and receive FIFO sizes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/fd11933f932df81d84f417a21e2179bd4fdcfdc1.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
All MSIOF variants support transferring data of multiple (2 or 4)
groups. Add definitions for the register bits related to multiple
groups, and enhance sh_msiof_spi_set_mode_regs() to accept a second
group size.
For now the second group is unused.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/be75e20cfcd2a6c0d73ab09e0126f902911adc69.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The Group Output Mask is not a single bit, but a bit field, containing
one bit for each of the four possible groups. Correct the definition.
Note that this change has no direct impact, as the driver only uses
the first group.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/ad268d67807cb7e544eddaf7a056793482a965d4.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum amount of data to transfer in a single DMA request is
calculated from the FIFO sizes (which is technically not 100% correct,
but a simplification, as it is limited by the maximum word count values
in the Transmit and Control Data Registers). However, in case there is
both data to transmit and to receive, the transmit limit is overwritten
by the receive limit.
Fix this by using the minimum applicable FIFO size instead. Move the
calculation outside the loop, so it is not repeated for each individual
DMA transfer.
As currently tx_fifo_size is always equal to rx_fifo_size, this bug had
no real impact.
Fixes: fe78d0b769 ("spi: sh-msiof: Fix FIFO size to 64 word from 256 word")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/d9961767a97758b2614f2ee8afe1bd56dc900a60.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The Clock-Synchronized Serial Interfaces with FIFO (MSIOF) driver
matches against both SoC-specific and family-specific compatible values
to maintain backwards-compatibility with old DTBs predating the
introduction of the family-specific compatible values.
For RZ/G1, the SoC-specific compatible match entry can be removed from
the driver: their DT always had the family-specific compatible values,
and thus there was never a need to add the SoC-specific compatible
values to the driver.
For R-Car Gen2 and M3-W, the SoC-specific compatible match entries can
be removed, too, as there are a few points in time where DT
backwards-compatibility was broken for other reasons:
- Legacy DT clock support is no longer supported since commit
58256143cf ("clk: renesas: Remove R-Car Gen2 legacy DT clock
support") in v5.5, and the addition of "renesas,rcar-gen2-msiof" to
DTS in v4.11 predates the completion of the clock conversion in
v4.15,
- Legacy DT LVDS support is no longer supported since commit
841281fe52 ("drm: rcar-du: Drop LVDS device tree backward
compatibility") in v5.18, and the addition of
"renesas,rcar-gen3-msiof" in commit 8b51f97138 ("arm64: dts:
r8a7796: Use R-Car Gen 3 fallback binding for msiof nodes") in v4.11
predates the LVDS conversion in commit 58e8ed2ee9 ("arm64:
dts: renesas: Convert to new LVDS DT bindings") in v4.20.
For R-Car H3, the SoC-specific compatible match entry cannot be removed,
as its purpose is to handle an SoC-specific quirk.
Suggested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/d33393ac7536bc3f0f624b079f70d80dd19843db.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Large part of the code uses the FIELD_PREP() macro already to construct
values to be written to hardware registers. Change the code to use also
the macro for more registers of which the corresponding bitmasks are
defined already.
This makes the code more readable. It also syncs the affected
codes with their counterparts in the 'qcom_nandc' driver, so it
makes it easier to spot the differences between the two
implementations.
No functional changes intended.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://patch.msgid.link/20250515-qpic-snand-use-bitmasks-v1-2-11729aeae73b@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the code to use the already defined CW_PER_PAGE_MASK
bitmask along with the FIELD_PREP() macro instead of using
magic values.
This makes the code more readable. It also syncs the affected
codes with their counterparts in the 'qcom_nandc' driver, so it
makes it easier to spot the differences between the two
implementations.
No functional changes intended.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://patch.msgid.link/20250515-qpic-snand-use-bitmasks-v1-1-11729aeae73b@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for internal DMA in Tegra234 devices. Tegra234 has an
internal DMA controller, while Tegra241 continues to use an external
DMA controller (GPCDMA). This patch adds support for both internal
and external DMA controllers.
Signed-off-by: Vishwaroop A <va@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20250513200043.608292-2-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI interface is activated before the CPOL setting is applied. In
that moment, the clock idles high and CS goes low. After a short delay,
CPOL and other settings are applied, which may cause the clock to change
state and idle low. This transition is not part of a clock cycle, and it
can confuse the receiving device.
To prevent this unexpected transition, activate the interface while CPOL
and the other settings are being applied.
Signed-off-by: Alessandro Grassi <alessandro.grassi@mailbox.org>
Link: https://patch.msgid.link/20250502095520.13825-1-alessandro.grassi@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Bence Csókás <csokas.bence@prolan.hu>:
The probe() function of the atmel-quadspi driver got quite convoluted,
especially since the addition of SAMA7G5 support, that was forward-ported
from an older vendor kernel. During the port, a bug was introduced, where
the PM get() and put() calls were imbalanced. To alleivate this - and
similar problems in the future - an effort was made to migrate as many
functions as possible, to their devm_ managed counterparts. The few
functions, which did not yet have a devm_ variant, are added in patch 1 of
this series. Patch 2 then uses these APIs to fix the probe() function.
