This patch adds the new struct ieee80211_rate_status and replaces
'struct rate_info *rate' in ieee80211_tx_status with pointer and length
annotation.
The struct ieee80211_rate_status allows to:
(1) receive tx power status feedback for transmit power control (TPC)
per packet or packet retry
(2) dynamic mapping of wifi chip specific multi-rate retry (mrr)
chains with different lengths
(3) increase the limit of annotatable rate indices to support
IEEE802.11ac rate sets and beyond
ieee80211_tx_info, control and status buffer, and ieee80211_tx_rate
cannot be used to achieve these goals due to fixed size limitations.
Our new struct contains a struct rate_info to annotate the rate that was
used, retry count of the rate and tx power. It is intended for all
information related to RC and TPC that needs to be passed from driver to
mac80211 and its RC/TPC algorithms like Minstrel_HT. It corresponds to
one stage in an mrr. Multiple subsequent instances of this struct can be
included in struct ieee80211_tx_status via a pointer and a length variable.
Those instances can be allocated on-stack. The former reference to a single
instance of struct rate_info is replaced with our new annotation.
An extension is introduced to struct ieee80211_hw. There are two new
members called 'tx_power_levels' and 'max_txpwr_levels_idx' acting as a
tx power level table. When a wifi device is registered, the driver shall
supply all supported power levels in this list. This allows to support
several quirks like differing power steps in power level ranges or
alike. TPC can use this for algorithm and thus be designed more abstract
instead of handling all possible step widths individually.
Further mandatory changes in status.c, mt76 and ath11k drivers due to the
removal of 'struct rate_info *rate' are also included.
status.c already uses the information in ieee80211_tx_status->rate in
radiotap, this is now changed to use ieee80211_rate_status->rate_idx.
mt76 driver already uses struct rate_info to pass the tx rate to status
path. The new members of the ieee80211_tx_status are set to NULL and 0
because the previously passed rate is not relevant to rate control and
accurate information is passed via tx_info->status.rates.
For ath11k, the txrate can be passed via this struct because ath11k uses
firmware RC and thus the information does not interfere with software RC.
Compile-Tested: current wireless-next tree with all flags on
Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt
Linux 5.10.113
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://lore.kernel.org/r/20220509173958.1398201-2-jelonek.jonas@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fill all requested rates (in case of ath9k 4 rate slots are
available, so fill all 4 instead of only 3), improves throughput in
noisy environment.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Link: https://lore.kernel.org/r/20220402153014.31332-2-ps.report@gmx.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AP may run out of BSS color after color collision
detection event from driver.
Disable BSS color collision detection if no free colors are
available based on bss color disabled bit sent as a part of
NL80211_ATTR_HE_BSS_COLOR attribute sent in
NL80211_CMD_SET_BEACON.
It can be reenabled once new color is available.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649867295-7204-3-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_ATTR_HE_BSS_COLOR attribute can be included in both
NL80211_CMD_START_AP and NL80211_CMD_SET_BEACON commands.
Move he_bss_color from cfg80211_ap_settings to cfg80211_beacon_data
and parse NL80211_ATTR_HE_BSS_COLOR as a part of nl80211_parse_beacon()
to have bss color settings parsed for both start ap and set beacon
commands.
Add a new flag he_bss_color_valid to indicate whether
NL80211_ATTR_HE_BSS_COLOR attribute is included.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649867295-7204-2-git-send-email-quic_ramess@quicinc.com
[fix build ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently track whether we're associated and which the
BSS is in the same variable (ifmgd->associated), but for
MLD we'll need to move the BSS pointer to be per link,
while the question whether we're associated or not is for
the whole interface.
Add ifmgd->assoc_bss that stores the pointer and change
ifmgd->associated to be just a bool, so the question of
whether we're associated can continue working after MLD
rework, without requiring changes, while the BSS pointer
will have to be changed/used checked per link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't need to copy this locally, we now only use the
variable to print before doing other things.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We never use the bssid argument to ieee80211_sta_connection_lost()
so we might as well just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to look it up from the ifmgd->associated
BSS configuration, we already maintain a local copy since
commit b0140fda62 ("mac80211: mlme: save ssid info to
ieee80211_bss_conf while assoc").
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we always track the BSSID there when we get associated,
these are equivalent, but ifmgd->bssid saves a dereference and
thus makes the code a bit smaller, and more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is tightly coupled to the sdata->u.mgd data
structure, so there's no reason for it to be in utils.
Move it to mlme.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ping-Ke's previous patch adjusted the CCMP AAD construction
to properly take the order bit into account, but failed to
update the (identical) GCMP AAD construction as well.
Unify the AAD construction between the two cases.
Reported-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20220506105150.51d66e2a6f3c.I65f12be82c112365169e8a9f48c7a71300e814b9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This memory allocation failure can be triggered by fault injection or
high pressure testing, resulting a WARN.
Fix this by replacing WARN with pr_warn.
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220511014453.1621366-1-dzm91@hust.edu.cn
Currently, upon virtual interface creation, wfx_add_interface() stores
a reference to the corresponding struct ieee80211_vif in private data,
for later usage. This is not needed when using the container_of
construct. This construct already has all the info it needs to retrieve
the reference to the corresponding struct from the offset that is
already available, inherent in container_of(), between its type and
member inputs (struct ieee80211_vif and drv_priv, respectively).
Remove vif (which was previously storing the reference to the struct
ieee80211_vif) from the struct wfx_vif, define a function
wvif_to_vif(wvif) for container_of(), and replace all wvif->vif with
the newly defined container_of construct.
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506170046.GA1297231@jaehee-ThinkPad-X1-Extreme
BSSID CAM is a kind of CAM that is used to determine if we receive a packet
or not. Add an entry to assist in debugging.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-6-pkshih@realtek.com
EDCCA signal can block transmitting in certain situation, so ignore this
signal and use others to decide transmitting time.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-4-pkshih@realtek.com
Set proper setting according to RX quota, and then it doesn't break buffer
due to size of received packet exceeding buffer size.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-3-pkshih@realtek.com
Modify NBI and PD boost settings according to different primary channels.
This setting can decrease the false alarm induced by DC.
Signed-off-by: Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-2-pkshih@realtek.com
Clean up the following smatch warning:
drivers/ssb/pci.c:917 ssb_pci_sprom_get() warn: ignoring unreachable
code.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506075814.115059-1-jiapeng.chong@linux.alibaba.com
This allows firmware to provide MAC address using device tree. Like in
case there is no MAC burned in wlan NVRAM.
Signed-off-by: Pavel Löbl <pavel@loebl.cz>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506044246.67146-1-pavel@loebl.cz
'vmm_table' array contains the size of data buffer length including host
header length. In 'vmm_table' array, the Zero value means the end of
vmm_entries that needs to transfer to firmware which is calculated based on
VMM free size in firmware.
Use 'vmm_table' valid entry check before fetching the entry from TX queue to
only copy valid number of entries to avoid possible NULL pointer exception
observed sometimes during large file transfers.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-5-ajay.kathat@microchip.com
Monitor(mon.) interface is used for handling the AP mode and 'ieee80211_ptr'
reference is not getting set for it. Like earlier implementation,
use register_netdevice() instead of cfg80211_register_netdevice() which
expects valid 'ieee80211_ptr' reference to avoid the possible crash.
Fixes: 2fe8ef1062 ("cfg80211: change netdev registration/unregistration semantics")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-3-ajay.kathat@microchip.com
The function number was not correct(reset to 0) when host resumes from
suspend state. Use hardcoded value in function base information
register(FBR base address) to re-initialize correctly on host resume.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-2-ajay.kathat@microchip.com
Increase firmware version array size to hold complete version information.
The firmware commit id(Build:) information is also part of the firmware
version string.
Firmware version format:
WILC_WIFI_FW_REL_XX_XX Build: XXXXX
e.g.
WILC_WIFI_FW_REL_15_6 Build: 12804
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-1-ajay.kathat@microchip.com
Fine tune algorithm of adaptivity sensitivity to avoid disconnecting
from AP suddenly in field.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506235045.4669-1-pkshih@realtek.com
With introduction of vmap'ed stacks, stack parameters can no
longer be used for DMA and now leads to kernel panic.
It happens at several places for the wl1251 (e.g. when
accessed through SDIO) making it unuseable on e.g. the
OpenPandora.
We solve this by allocating temporary buffers or use wl1251_read32().
Tested on v5.18-rc5 with OpenPandora.
Fixes: a1c510d0ad ("ARM: implement support for vmap'ed stacks")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1676021ae8b6d7aada0b1806fed99b1b8359bdc4.1651495112.git.hns@goldelico.com
qtnfmac chooses its own magic NAPI weight so switch to the new
API created for those who don't use NAPI_POLL_WEIGHT.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504163316.549648-4-kuba@kernel.org
In client mode, we can't connect to hidden SSID APs or SSIDs not advertised
in beacons on DFS channels, since we're forced to passive scan. Fix this by
sending out a probe request immediately after the first beacon, if active
scan was requested by the user.
Cc: stable@vger.kernel.org
Reported-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220420104907.36275-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If statement is meaningless because the code will goto out regardless of
whether fast_tx is NULL or not.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220413091902.27438-1-hbh25y@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Follow IEEE 802.11-21 that HTC subfield masked to 0 for all data frames
containing a QoS Control field. It also defines the AAD length depends on
QC and A4 fields, so change logic to determine length accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220324004816.6202-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since internal_flags is only 8 bits, we can only have one
more internal flag. However, we can obviously never use all
of possible the combinations, in fact, we only use 14 of
them (including no flags).
Since we want more flags for MLO (multi-link operation) in
the future, refactor the code to use a flags selector, so
wrap all of the .internal_flags assignments in a IFLAGS()
macro which selects the combination according to the pre-
defined list of combinations.
When we need a new combination, we'll have to add it, but
again we will never use all possible combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20220414140402.70ddf8af3eb0.I2cc38cb6a10bb4c3863ec9ee97edbcc70a07aa4b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We haven't used this function for years, since commit c781944b71
("cfg80211: Remove unused cfg80211_can_use_iftype_chan()") which
itself removed a function unused since commit 97dc94f1d9
("cfg80211: remove channel_switch combination check"), almost eight
years ago.
Also remove the now unused enum cfg80211_chan_mode and some struct
members that were only used for this function.
Link: https://lore.kernel.org/r/20220412220958.1a191dca19d7.Ide4448f02d0e2f1ca2992971421ffc1933a5370a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This initial vesion is usable now. It can support STA, AP and monitor
modes, so we can add 8852ce to Kconfig and Makefile.
We are still working on some features, such as deep power save, and BT
coexistence. But, this version still can have a good WiFi-only performance
already, and will continue to fine tune power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-9-pkshih@realtek.com
By experiments, it spends ~45/1090~2480us to enter/leave low power mode,
so the old polling interval 1000us can waste time. Use smaller polling
interval depends on experimental results to reduce the time to transition
state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-5-pkshih@realtek.com
The chip_info include BT coexistence tables, size and number of hardware
components, and supported functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-4-pkshih@realtek.com
The commit 16b44ed0ff ("rtw89: add RF H2C to notify firmware") is to
add firmware command, and this commit is to prepare the channels. Then,
firmware can get proper channels.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-2-pkshih@realtek.com
