btintel_pcie_submit_rx() used frbd_index > rxq->count to guard the
FRBD array access, allowing frbd_index == rxq->count to pass through
and index one element past the end of the array. Change the check to
>= rxq->count so every out-of-range index is rejected.
This issue was reported by Claude Mythos.
Fixes: c2b636b3f7 (Bluetooth: btintel_pcie: Add support for PCIe transport)
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In btmtksdio_shutdown(), pm_runtime_get_sync() is called at the
beginning of the function. However, if sending the WMT function
control command fails later, the driver returns early.
It bypasses the corresponding pm_runtime_put_noidle() and
pm_runtime_disable() calls, leaking the PM usage counter and leaving PM
runtime enabled indefinitely.
Fall through to execute the PM runtime cleanup block even if WMT errors.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btmtksdio.c and btmtkuart.c cast a received WMT event straight to
struct btmtk_hci_wmt_evt and read its op/flag fields without checking
the event is long enough to contain them, unlike btmtk.c. The
FUNC_CTRL case then further casts to struct btmtk_hci_wmt_evt_funcc
and reads its 2-byte status field, again without a length check.
Firmware that sends a short or malformed WMT event makes both drivers
read past the end of the received SKB.
Mirror btmtk.c: validate the base WMT header with skb_pull_data()
before touching any of its fields, and when a FUNC_CTRL event turns
out to be the short, header-only form (a plain enable/disable ack
with no status word), decode the result from the header's own flag
byte instead (0 = success, otherwise failure).
Verified setup on MT7920, MT7921, MT7922 and MT7925: no regression.
Fixes: 9aebfd4a22 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Fixes: e0b67035a9 ("Bluetooth: mediatek: update the common setup between MT7622 and other devices")
Assisted-by: Claude:claude-opus-5
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A too-short BTMTK_WMT_FUNC_CTRL event (WMT header only, no trailing
2-byte status word) is always treated as BTMTK_WMT_ON_UNDONE. This
short form is how firmware acks a plain enable/disable request, and
the actual result is carried in the header's own flag byte (0 =
success), not a separate status word. Decode it from there instead of
assuming failure.
Verified setup on MT7920, MT7921, MT7922 and MT7925: no regression.
Fixes: e3ac0d9f1a ("Bluetooth: btmtk: accept too short WMT FUNC_CTRL events")
Assisted-by: Claude:claude-opus-5
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A BIS connection is matched to its parent socket by looking for a
socket in BT_LISTEN state with the same BIG handle:
iso_conn_ready()
if (test_bit(HCI_CONN_BIG_SYNC, &hcon->flags))
parent = iso_get_sock(hdev, &hcon->src, &hcon->dst,
BT_LISTEN, iso_match_big_hcon, hcon);
The socket was only moved to BT_LISTEN after iso_conn_big_sync()
returned, while the LE BIG Create Sync command has already been queued
by then. If the BIG sync is established before the state is updated,
which is easy to hit with an emulated controller as the command may
complete in a few hundred microseconds, no parent is found and the BIS
connections are never notified to the listening socket.
The user space is then left waiting for connections that never arrive,
e.g. bluetoothd never completes a MediaTransport1.Acquire of a
Broadcast Sink transport.
Move the socket to BT_LISTEN before requesting the BIG sync, so the
state is visible by the time the command is queued, and restore the
previous state if the request could not be started. Since the socket is
briefly visible as a listening socket, child sockets may have been
queued in the meantime, so drain the accept queue before restoring the
state: the cleanup paths of BT_CONNECT2/BT_CONNECTED don't do it and the
children would be left with a dangling parent pointer.
Fixes: fbdc4bc472 ("Bluetooth: ISO: Use defer setup to separate PA sync and BIG sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
iso_get_sock() returns the parent socket with a reference held, which is
dropped by sock_put() once the child socket has been set up. The error
path taken when iso_sock_alloc() fails only calls release_sock() and
returns, leaking the reference and thus the parent socket itself.
Drop the reference on that path as well.
Fixes: fa224d0c09 ("Bluetooth: ISO: Reassociate a socket with an active BIS")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_dev_close_sync() clears hdev->local_codecs after releasing hdev->lock.
Codec list additions and both traversals in sco_sock_getsockopt() use that
lock, but the close path does not. A close and BT_CODEC query can therefore
interleave as follows:
hci_dev_close_sync() sco_sock_getsockopt()
hci_dev_lock()
fetch codec entry
hci_codec_list_clear()
kfree(entry)
read entry->id
The reader then accesses an entry which the close path has freed. KASAN
reported:
BUG: KASAN: slab-use-after-free in sco_sock_getsockopt+0xfa0/0xfe0
Read of size 1 at addr ffff8881001c3450
Call Trace:
sco_sock_getsockopt+0xfa0/0xfe0
do_sock_getsockopt+0x537/0x7b0
__sys_getsockopt+0xf2/0x170
Allocated by task 92:
hci_codec_list_add.isra.0+0x2c/0x440
hci_read_codec_capabilities+0x224/0x590
hci_read_supported_codecs+0x2c2/0x640
Freed by task 92:
kfree+0x131/0x3c0
hci_codec_list_clear+0xd8/0x160
hci_dev_close_sync+0x92a/0xfa0
Take hdev->lock around the clear operation at its existing point in the
close path. This makes the clear wait for active readers and prevents a new
traversal until the list is empty without changing teardown ordering.
Fixes: b938790e70 ("Bluetooth: hci_codec: Fix leaking content of local_codecs")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP
is set (for example, for the WCN399x family). A failed hci_dev_open_sync()
following a successful qca_setup() calls hdev->close() but not
hdev->shutdown(), so the port is closed while power->vregs_on is left true.
qca_serdev_remove() then passes its power->vregs_on test and calls
qca_power_off(), which writes to the closed port unconditionally.
Seen on a WCN3988 by unbinding the driver after a controller failure. The
trace below is from a 7.0.0 based kernel, where qca_power_off() was still
named qca_power_shutdown():
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000038
Call trace:
tty_set_termios+0x50/0x238 (P)
ttyport_set_baudrate+0x84/0xc0
serdev_device_set_baudrate+0x24/0x40
qca_power_shutdown+0x158/0x1fc [hci_uart]
qca_serdev_remove+0x54/0x68 [hci_uart]
serdev_drv_remove+0x1c/0x2c
device_remove+0x4c/0x80
device_release_driver_internal+0x1cc/0x224
device_driver_detach+0x18/0x24
unbind_store+0xb4/0xc0
Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place
it closes the port, before writing to it. The regulator disable is left
unconditional so the controller is still powered down.
The dangling serport->tty that turns this into a use-after-free is
addressed in a separate patch.
Fixes: fa9ad876b8 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Signed-off-by: Ibrahim Abdelkader <iabdelka@qti.qualcomm.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Read Local Supported Codecs parsers consume the variable-sized
standard codec array before parsing the vendor codec count. Although the
initial reply-size check includes a vendor count byte in the fixed layout,
it does not guarantee that the byte remains after the standard codec array.
If a controller reply ends immediately after that array, calculating the
vendor codec array size reads vnd_codecs->num beyond the skb data. Use
skb_pull_data() to validate and consume each codec header before using its
count in both command variants.
Fixes: 8961987f3f ("Bluetooth: Enumerate local supported codec and cache details")
Fixes: 9ae664028a ("Bluetooth: Add support for Read Local Supported Codecs V2")
Cc: stable@vger.kernel.org
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Laxman Acharya Padhya <acharyalaxman8848@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
An identity address only reaches a peer that is advertising an RPA if the
controller resolves it on our behalf. Where it cannot, the host has to put
the peer's on-air address on air itself.
hci_connect_le() still swaps the caller's identity address for the peer's
cached RPA before creating the connection, but __hci_conn_add() resolves
the RPA back to the identity address when it stores it, so the identity is
what goes out. Storing the identity is right when the controller
translates it on the way to the radio; without LL Privacy, or with this
peer absent from the resolving list, nothing does.
A peer advertising an RPA cannot answer its identity address, so the
attempt burns a full create-connection timeout. That is not merely a slow
connect: a controller without extended scanning cannot scan while it is
initiating, so every dead attempt also takes the scanner off the air for
the whole timeout.
Measured on a CYW43438, which reports neither LL Privacy nor extended
advertising (LE features 3f 00 00 08 00 00 00 00), against a peer
advertising a resolvable private address the host holds the IRK for, with
the connection requested on the peer's identity address:
before: LE Create Connection to the identity address, public type
1.61s -> 22.07s, then LE Create Connection Cancel
LE Connection Complete: Unknown Connection Identifier (0x02)
after: LE Create Connection to the peer's RPA, random type
LE Connection Complete: Success
Advertising reports reaching the host per second, same window, same five
unrelated devices on the adapter:
before 1s:2 [nothing from 2s through 21s] 22s:5 23s:3
after 0s:11 1s:5 2s:2 3s:5 4s:3 5s:4 ... 21s:2 22s:1 23s:2
One dead connect costs twenty seconds of scanning for every device on the
adapter, not just the one being dialled.
Keep the RPA in conn->dst unless the controller will translate the
identity address: address resolution enabled and the peer's identity
actually programmed into the resolving list. Testing ll_privacy_capable()
alone would not be enough: it reports the feature bit, not whether
resolution is switched on and not whether this peer is in the list.
Resolution is cleared with the other volatile flags on power-off and
switched off again while suspend pauses scanning, and a peer's IRK is only
programmed along the accept list path, so a direct-connect target, a peer
without HCI_CONN_FLAG_ADDRESS_RESOLUTION, and one that did not fit in a
full list are all absent from it.
With the peer programmed, the identity address stays in conn->dst and the
controller translates it: measured on an Intel controller, the host dials
the identity and LE Enhanced Connection Complete reports Resolved Public
with the peer's RPA in the separate peer resolvable private address field.
With the peer absent from the list the same setup dials the RPA itself.
Everything downstream already copes with an RPA in conn->dst: it is what
every outgoing LE connection stored before 14b06c3a88, the connection
complete event names the address that was dialled, and
le_conn_complete_evt() resolves it back to the identity once the link is
up. ISO links keep the unconditional conversion: they are created from an
existing ACL or a periodic sync and never dial this address themselves.
Keeping the RPA is only right while the peer is still using it, which is
why the preceding patch drops the cached RPA as soon as the peer is seen
advertising its identity address. Without that, a peer that turns privacy
off would be dialled on the address it abandoned rather than the one it
is answering on.
Fixes: 14b06c3a88 ("Bluetooth: HCI: Always use the identity address when initializing a connection")
Assisted-by: Claude:claude-opus-5
Assisted-by: Claude:claude-fable-5
Signed-off-by: Radek Podgorny <radek@podgorny.cz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_devcd_handle_pkt_init() arms dump_timeout and coredump producers
queue dump_rx without holding an hdev reference. Unregister leaves both
works live, so disconnecting during an active dump lets them access hdev
after hci_release_dev() frees it.
Shut down coredump processing during unregister. Close the producer gate
under dump_q.lock before disabling both works, then free the active buffer
and queued packets under hci_dev_lock. Serializing the gate with enqueue
prevents controller-specific workers from adding packets after the final
purge.
Fixes: 9695ef876f ("Bluetooth: Add support for hci devcoredump")
Reported-by: syzbot+b170dbf55520ebf5969a@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=b170dbf55520ebf5969a
Reported-by: Aby Sam Ross <abysamross@gmail.com>
Link: https://lore.kernel.org/r/20260322210849.68743-1-abysamross@gmail.com
Suggested-by: Aby Sam Ross <abysamross@gmail.com>
Reported-by: Tristan Madani <tristan@talencesecurity.com>
Link: https://lore.kernel.org/r/20260814231248.3096377-1-tristmd@gmail.com
Reported-by: Xiang Mei <xmei5@asu.edu>
Assisted-by: OpenAI Codex:gpt-5
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btintel_pcie_prepare_tx() copies skb->len bytes into a fixed
BTINTEL_PCIE_BUFFER_SIZE (4096) DMA slot via an unchecked memcpy.
Oversized packets are currently rejected only in
btintel_pcie_send_frame(); any future caller of
btintel_pcie_send_sync() would silently overflow the DMA buffer.
Add the bounds check in btintel_pcie_send_sync() itself, right
before skb_push() and the DMA copy.
Assisted-by: Copilot:claude-sonnet-5 code-review code-generation
Fixes: 6e65a09f92 ("Bluetooth: btintel_pcie: Add *setup* function to download firmware")
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_send_acl(), hci_send_sco() and hci_send_iso() queue hdev->tx_work
unconditionally. They can run from the L2CAP/SCO/ISO socket send path
while hci_dev_close_sync() is draining hdev->workqueue (HCIDEVDOWN
racing with a socket write). Since that queue_work() is not chained
work from the tx_work worker itself, __queue_work() sees the queue
marked __WQ_DRAINING, warns "cannot queue %ps on wq %s", and drops
the work:
WARNING: CPU: 1 PID: 5985 at kernel/workqueue.c:2352 __queue_work
Call Trace:
queue_work_on
l2cap_chan_send
l2cap_sock_sendmsg
...
hci_dev_close_sync() already sets HCI_CMD_DRAIN_WORKQUEUE before
draining, but only hci_cmd_work() and handle_cmd_cnt_and_timer()
check it before queuing. Route the tx_work producers through the
same guard via a shared hci_sched_tx() helper.
Fixes: 525daaea45 ("Bluetooth: hci_sync: Set HCI_CMD_DRAIN_WORKQUEUE during device close")
Reported-by: syzbot+b6919040d9958e2fc1ae@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=b6919040d9958e2fc1ae
Signed-off-by: ThangNN99 <ngocthang2710.1999@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
eir_get_service_data() reads a 16-bit UUID from the service data using
get_unaligned_le16() without first checking that the data is long enough
to hold a UUID16 (2 bytes). If a malformed EIR entry has a service data
field with only 1 byte of payload (field_len=2), eir_get_data() returns
dlen=1. The subsequent get_unaligned_le16() then reads 1 byte past the
field boundary.
Additionally, if the corrupted UUID happens to match, the length
calculation "dlen - 2" underflows to SIZE_MAX since dlen is size_t.
Current callers either pass NULL for the length parameter or bounds-check
the returned length, but future callers may not.
Add a check that dlen >= sizeof(u16) and skip fields that are too short
to contain a valid UUID16.
Fixes: 8f9ae5b3ae ("Bluetooth: eir: Add helpers for managing service data")
Cc: stable@vger.kernel.org
Signed-off-by: Aamir Ahmed <elb12345@hotmail.co.uk>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The NXP IW610 module exposes itself as a composite USB device
(0471:0215) with three interfaces: two real Bluetooth HCI interfaces
(class 0xe0) and one vendor-specific WiFi interface (class 0xff) used
by mwifiex-nxp.
The composite device's whole USB descriptor reports class 0xe0/01/01
(Bluetooth), so btusb_table's generic USB_DEVICE_INFO(0xe0, 0x01, 0x01)
entry matches every interface, not just the two real HCI ones -- btusb
ends up binding the WiFi interface too, and mwifiex-nxp never gets it.
Fix:
1. In btusb_table (the table the USB core actually matches against),
explicitly ignore the WiFi interface via BTUSB_IGNORE, ahead of the
generic entry.
2. In quirks_table, scope the existing BTUSB_MARVELL entry to the BT
interface class instead of matching the whole device by VID/PID
(harmless either way since quirks_table isn't consulted for initial
binding, but keep it correct).
Not upstream anywhere: checked NXP's own i.MX kernel fork
(nxp-imx/linux-imx), no IW610 references in btusb.c on any branch --
their reference designs wire this chip differently (WiFi over SDIO
per their release notes), so they never hit this.
Signed-off-by: Nicolas Thibert <nithibert@gmail.com>
Cc: stable@vger.kernel.org
Assisted-by: LLM (Claude Sonnet 5, Anthropic)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We can hit a division by zero crash in tcp_rcvbuf_grow()
and tcp_rcv_space_adjust():
divide error: 0000 [#1] PREEMPT SMP
RIP: 0010:tcp_rcvbuf_grow+0x187/0x450 net/ipv4/tcp_input.c:939
...
grow = div_u64(((u64)rcvwin << 1) * (newval - oldval), oldval);
The division uses oldval = tp->rcvq_space.space as divisor.
When tp->rcvq_space.space is zero, this leads to a divide-by-zero
exception.
tp->rcvq_space.space is initialized in tcp_init_buffer_space():
tp->rcvq_space.space = min3(tp->rcv_ssthresh, tp->rcv_wnd,
(u32)TCP_INIT_CWND * tp->advmss);
If tcp_rmem[1] is configured to very small values (such as 1),
sk->sk_rcvbuf is initialized to 1. Then tcp_full_space(sk), which
computes (sk->sk_rcvbuf * scaling_ratio) >> 8, truncates to 0.
This sets tp->window_clamp = 0, tp->rcv_ssthresh = 0, and
tp->rcvq_space.space = 0. Later, when data arrives and DRS is invoked,
tcp_rcvbuf_grow() divides by oldval == 0.
Back in 2015, commit b1cb59cf2e ("net: sysctl_net_core: check SNDBUF
and RCVBUF for min length") ensured that net.core.rmem_default and
net.core.rmem_max cannot be set below SOCK_MIN_RCVBUF. Similarly,
SO_RCVBUF setsockopt enforces max_t(int, val * 2, SOCK_MIN_RCVBUF).
However, net.ipv4.tcp_rmem still had .extra1 = SYSCTL_ONE, allowing
arbitrarily small values.
Because SOCK_MIN_RCVBUF depends on sizeof(struct sk_buff) and cacheline
alignment, its value varies across architectures and configuration options.
Using a fixed constant of 4096 ensures a predictable, architecture-
independent lower bound that is safely above SOCK_MIN_RCVBUF everywhere
and matches the documented 4K default.
Fix this by setting tcp_rmem.extra1 to 4096 and updating the documentation.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260912144848.3448026-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cover the new TCA_HHF_HH_FLOWS_LIMIT bound: values above 2*HH_FLOWS_CNT
(4294967295, 65536, 2049) are rejected with the configured limit left
untouched on both the change and the add path, the boundary value 2048 is
accepted (installed at 100 first so the boundary change is load-bearing),
and an add-time hh_limit 500 is preserved instead of being clobbered by
the default.
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Tested-by: hybris <hybris@mojatatu.ai>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/QDISC-B855.v1.20260911153152@mojatatu.com.2
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
hhf_change() stores TCA_HHF_HH_FLOWS_LIMIT with no upper bound. A huge
hh_flows_limit lets each new heavy-hitter flow pass the
hh_flows_current_cnt check in alloc_new_hh() and forces a fixed-size
kzalloc(GFP_ATOMIC) per flow under spoofed traffic, for unbounded memory
growth.
Bound the attribute with NLA_POLICY_MAX() at 2*HH_FLOWS_CNT (the
hhf_init() default) and report the rejected value via extack. The
deprecated nested parse is kept: legacy tc does not set NLA_F_NESTED on
TCA_OPTIONS. Configs relying on hh_limit above the default were relying
on unbounded, unsafe behaviour and are not supported going forward.
hhf_init() also ran hhf_change() before setting the default
hh_flows_limit, so a user-supplied hh_limit at add time was clobbered
back to 2048. Set the default before hhf_change() so the configured
value sticks.
This is a follow-up to commit eb56a495f5 ("net/sched: hhf: clamp
quantum in change and init paths"), which bounded the quantum of the
same qdisc; the hh_flows_limit bound is the remaining unbounded knob of
that series' scope.
Conditions to recreate the bug: CAP_NET_ADMIN in a user namespace;
tc qdisc change dev X root hhf hh_limit 4294967295 succeeds and the
value is echoed by tc qdisc show, unbounding heavy-hitter flow
allocations; also tc qdisc add dev X root hhf hh_limit 500 stores 2048
instead of 500.
Fixes: 10239edf86 ("net-qdisc-hhf: Heavy-Hitter Filter (HHF) qdisc")
Cc: stable@vger.kernel.org
Reported-by: Sashiko (gemini) <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260822195509.112717-1-jhs@mojatatu.com
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Tested-by: hybris <hybris@mojatatu.ai>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/QDISC-B855.v1.20260911153152@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is a follow-up of one of sashiko's pre-existing bug reports.
br_mst_set_state() calls switchdev_port_attr_set() for nonzero MSTIs
while holding rcu_read_lock() which invokes the blocking switchdev
notifier chain and may sleep. Nonzero MSTI changes come from netlink
with rtnl held. Move the switchdev call before entering the rcu section and
assert that rtnl is held.
The call cannot be deferred because netlink needs its error and extack.
Also DSA reads the old bridge MST state during the callback and checks it.
A deferred callback will be late and will see the updated state.
Fixes: 3a7c1661ae ("net: bridge: mst: fix vlan use-after-free")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260911105021.1385934-1-razor@blackwall.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
skfp_ctl_set_mac_address() calls ResetAdapter() unconditionally, without
checking netif_running(). ResetAdapter() first calls card_stop(), which
sets smc->hw.hw_state to STOPPED, and then mac_drv_clear_tx_queue(),
which walks the two transmit queues:
for (i = QUEUE_S; i <= QUEUE_A0; i++) {
queue = smc->hw.fp.tx[i] ;
...
t = queue->tx_curr_get ;
smc->hw.fp.tx[] is only populated by init_tx(), which is reached from
skfp_open() through init_smt() -> init_fddi_driver() -> init_fplus() ->
init_mac() -> init_tx(). The private area is allocated and zeroed by
alloc_fddidev(), so on an interface that has never been brought up both
queue pointers are still NULL. The hw_state test at the top of
mac_drv_clear_tx_queue() does not catch this, because card_stop() has
just set STOPPED; the function proceeds into the loop and dereferences
NULL. ResetAdapter() does call init_smt() itself, but only after the
queues have been cleared.
Setting the MAC address on a down interface therefore oopses:
ip link set dev fddi0 address 02:00:00:00:00:01
BUG: KASAN: null-ptr-deref in mac_drv_clear_tx_queue+0x68/0x2c0 [skfp]
Read of size 8 at addr 0000000000000010 by task ip/302
Call Trace:
<TASK>
mac_drv_clear_tx_queue+0x68/0x2c0 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
ResetAdapter+0x29/0x100 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
skfp_ctl_set_mac_address+0x57/0x80 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
netif_set_mac_address+0x1e4/0x2c0
do_setlink+0x684/0x2680
</TASK>
Address 0x10 is the offset of tx_curr_get, the third pointer in
struct s_smt_tx_queue, on 64-bit. mac_drv_clear_rx_queue(), which
ResetAdapter() calls immediately afterwards, dereferences
smc->hw.fp.rx[QUEUE_R1] in the same way behind the same ineffective
hw_state test; the transmit queue merely crashes first. Both are
covered by the guard below.
Skip the adapter reset when the interface is down. dev_addr_set() is
left unconditional, so the new address is still recorded in
dev->dev_addr. Nothing is lost by not resetting the adapter here:
skfp_open() deliberately re-reads the factory address on every open,
read_address(smc, NULL);
eth_hw_addr_set(dev, smc->hw.fddi_canon_addr.a);
and the comment above it states this is done to discard exactly such an
address override across a close/open cycle. An address set while the
interface is down could not have survived the following open even
before this change, so the guard removes no working behaviour. Guarding
the hardware side of ndo_set_mac_address() with netif_running() is
established practice; skge_set_mac_address() has done so since commit
2eb3e621c4 ("skge: set mac address bonding fix").
Guarding the reset as a whole, rather than NULL-checking the queues, is
also what the rest of the driver expects. After a previous open/close
the queue pointers are stale but non-NULL, so there is no crash, yet
ResetAdapter() goes on to call smt_online() and STI_FBI() ("Enable
Board Interrupts") while skfp_close() has already called free_irq() -
the adapter would be brought back online with no handler installed. The
only other ResetAdapter() caller is skfp_interrupt(), which by
construction runs only while the device is open.
Found by automated driver testing against an emulated SysKonnect FDDI
adapter under a KASAN-enabled 7.0.0 kernel. Triggering it requires
CAP_NET_ADMIN.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Assisted-by: LLM KASAN
Signed-off-by: Hohyun Sim <tlaghgus0425@korea.ac.kr>
Link: https://patch.msgid.link/20260910063743.110747-1-tlaghgus0425@korea.ac.kr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the forward output route cannot be used in icmp_route_lookup(),
it enters the "reverse path" and calls ip_route_input() on fl4_dec.daddr,
the original packet's source address.
ip_route_input() only returns an error for truly invalid packets. For
unreachable addresses it will succeed and return an input route whose
dst.output is set to ip_rt_bug(). The existing check only rejects
RTN_LOCAL routes, so the RTN_UNREACHABLE route types can still be returned
and later used for output, syzkaller triggering a WARN_ON_ONCE()
in ip_rt_bug() as bellow:
------------[ cut here ]------------
WARNING: net/ipv4/route.c:1273 at ip_rt_bug+0x14/0x20
RIP: 0010:ip_rt_bug+0x14/0x20
Call Trace:
ip_push_pending_frames+0xfa/0x100
__icmp_send+0x905/0xf10
ip_options_compile+0xc0/0xd0
ip_rcv_finish_core+0x321/0xae0
ip_rcv+0x1de/0x260
__netif_receive_skb_one_core+0x11a/0x130
netif_receive_skb+0x7b/0x260
tun_get_user+0x11bf/0x1c10
------------[ cut here ]------------
Reject input route that is RTN_UNREACHABLE to fix it. The net warning
is only printed for RTN_LOCAL, as RTN_UNREACHABLE is not the result of
a race condition.
Fixes: 8b7817f3a9 ("[IPSEC]: Add ICMP host relookup support")
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Link: https://patch.msgid.link/20260910140042.1880242-1-dongchenchen2@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bcmgenet_hfb_init() runs INIT_LIST_HEAD() on priv->rxnfc_list, which drops
every rule off the list, and bcmgenet_open() calls it on each ifup. Every
rule the user configured is silently lost:
# ethtool -N eth0 flow-type ether dst $MAC action 0
Added rule with ID 0
# ethtool -n eth0 | grep -c Filter:
1
# ip link set eth0 down && ip link set eth0 up
# ethtool -n eth0 | grep -c Filter:
0
Initialise the lists once at probe and restore the rules on open, as
bcmgenet_resume() already does.
Fixes: 3e37095228 ("net: bcmgenet: add support for ethtool rxnfc flows")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260913190052.939955-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mxl862xx_setup() arms the stats poll before mxl862xx_setup_mdio(), and
nothing stops it until dsa_register_switch() has returned an error to
mxl862xx_probe(). DSA frees the dsa_port list before it returns, so a
poll that fires once .setup or a later step of dsa_tree_setup() has
failed walks freed ports. On shutdown the user ports stay registered,
and the WORK_STOPPED flag test in mxl862xx_get_stats64() is not atomic
with the cancel in mxl862xx_shutdown(), so a re-arm that read the flag
before it was set queues the poll after cancel_delayed_work_sync() has
returned.
Arm the poll once .setup has succeeded and stop it from a .teardown op,
which DSA calls on unregister and after a failed registration, in both
cases before it frees the ports. Use disable_delayed_work_sync() there
and in shutdown(): it drains a running poll as the cancel did and turns
every later attempt to queue the work into a no-op, so the re-arm
cannot bring the poll back. remove() and the probe error path only set
WORK_STOPPED, which crc_err_work tests before it walks the ports.
Fixes: a21d33a526 ("net: dsa: mxl862xx: implement .get_stats64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/1eb6f7fc1789b67e4b11e3f4d5ff080d0b6f7cbb.1789045590.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an SRv6 packet arrives on an interface enslaved to a VRF,
vrf_ip6_rcv() sets IP6SKB_L3SLAVE in IP6CB, but decap_and_validate()
has never set IPSKB_L3SLAVE in IPCB. The bit stayed clear in the
common case, and with CONFIG_IPV6_MIP6 the leftover frag_max_size of
a reassembled outer packet could even set it, with no VRF involved.
Commit 44930446dd ("ipv6: seg6: clear IPv4 control block on IPIP
decapsulation") then made the unreliable bit reliably clear.
The effect of the missing flag is visible with End.DX4 when a
delivery to a local address of the node reaches the socket lookup.
For example, a UDP socket bound to the enslaved ingress interface
does not receive any of the decapsulated packets, while an unbound
socket outside the VRF does.
This contradicts Documentation/networking/vrf.rst: by default the
scope of an unbound UDP or TCP socket is limited to the default VRF.
Set IPSKB_L3SLAVE for IPv4 in decap_and_validate(), which already does
the same for IPv6. The socket lookup then matches the decapsulated
packet like any other packet received on that enslaved interface. Such
a packet matches an unbound UDP or TCP socket only when
udp_l3mdev_accept or tcp_l3mdev_accept is set.
Fixes: 891ef8dd2a ("ipv6: sr: implement additional seg6local actions")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Hangbin Liu <liuhangbin@kylinos.cn>
Link: https://patch.msgid.link/20260913194421.31-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mtk_phy_led_hw_ctrl_get() reports TRIGGER_NETDEV_LINK whenever any of the
speed bits in on_set is on, and in addition reports every individual
TRIGGER_NETDEV_LINK_* bit that is set. The netdev trigger refuses that
combination: netdev_led_attr_store() rejects TRIGGER_NETDEV_LINK together
with any per-speed rule, and it validates the whole resulting mode rather
than just the bit being written. Once the hardware has any link bit
programmed, every write to the trigger attributes of that LED therefore
fails with -EINVAL and the LED can no longer be configured.
The rules are also fed back into the hardware: the trigger stores what is
read back, and a later write of device_name programs it again, expanding
TRIGGER_NETDEV_LINK to every speed in on_set. An LED configured for a
single speed is thereby silently widened to "on at any link speed".
Both are easy to see on the EcoNet EN7528, whose four PHYs share one LED
block. The first LED programs the block correctly, the second reads those
rules back and rewrites them widened, and the remaining two then read the
widened value, so an LED configured for "link_10 link_100" ends up lit on a
1000 Mbps link.
on_set holds every speed the LED can indicate and is exactly what
mtk_phy_led_hw_ctrl_set() programs for TRIGGER_NETDEV_LINK, so report the
speed independent rule only when all of them are on, and the individual
speeds otherwise. The mapping is then the inverse of the one used when
programming the LED and round trips without changing the register.
Fixes: c66937b0f8 ("net: phy: mediatek-ge-soc: support PHY LEDs")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260912134306.3544329-1-naseefkm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hand-written bitfield offsets in is_link_up(), is_autoneg_enabled()
and is_autoneg_completed() were correct when the abstraction was
merged: at that time autoneg, link, and autoneg_complete were at bits
13, 14, and 15 of struct phy_device's first bitfield unit. Commit
2796ff1e3d ("net: phy: add flag is_genphy_driven to struct phy_device")
later inserted is_genphy_driven just before autoneg, shifting the three
fields up by one, so the accessors now read:
is_link_up() reads bit 14 = autoneg
is_autoneg_enabled() reads bit 13 = is_genphy_driven
is_autoneg_completed() reads bit 15 = link
The official ax88796b Rust driver uses all three accessors in its
read_status() implementation, so it inherits the bug.
phy_attach_direct() sets is_genphy_driven only when it falls back to
the generic driver, and ax88796b has a real driver, so
is_genphy_driven stays 0. The broken is_autoneg_enabled() therefore
reads bit 13 as 0, compares it against AUTONEG_ENABLE (1), and always
returns false, so read_status() never reaches the
resolve_aneg_linkmode() call.
The ordinary bindgen accessors take &self. Calling them through
(*phydev).link() would create a shared reference to the complete
bindings::phy_device, which is not appropriate for an object wrapped in
Opaque.
Use the bindgen-generated raw accessors (link_raw(), autoneg_raw(),
and autoneg_complete_raw()) instead. They retain the bit positions and
endianness handling generated from the C layout without creating a Rust
reference to the complete phy_device. Drop the hand-written numbers
together with the TODO comment that marked them as a stopgap.
The raw accessors are only emitted by bindgen 0.71 and later, and were
added at the Rust-for-Linux project's request, so this fix can only be
backported to stable branches whose minimum bindgen version is at least
that, hence the scope on the Cc: stable line below.
Found by a static equivalence audit (C2RustDrv, a C-to-Rust driver
migration tool) that compares hand-written bitfield offsets against
the bindgen layout of struct phy_device. Verified by building the
bindings and checking the generated accessors; no runtime testing was
possible without PHY hardware.
Fixes: 2796ff1e3d ("net: phy: add flag is_genphy_driven to struct phy_device")
Cc: stable@vger.kernel.org # Only 7.1.y and later (requires bindgen's raw pointer accessors).
Link: https://github.com/rust-lang/rust-bindgen/issues/2674
Signed-off-by: Chunfeng Song <springbreeze@stu.pku.edu.cn>
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20260910055110.167110-1-springbreeze@stu.pku.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rds_ib_cm_connect_complete() runs from the RDMA-CM event handler with
conn->c_cm_lock held. When the peer negotiates a protocol version
older than RDS_PROTOCOL_COMPAT_VERSION, the handler calls
rds_conn_destroy(), which is only safe in the rmmod path: it
synchronously tears the connection down and flush_work()es the
shutdown work cp_down_w.
That shutdown work (rds_conn_shutdown()) needs cp_cm_lock, which is
the very lock the event handler still holds, so the flush never
completes: the two workers wait on each other and the RDS connection
workqueues stall for good.
All other RDMA-CM failure paths (REJECTED, CONNECT_ERROR,
DISCONNECTED) use rds_conn_drop(), which marks the connection
RDS_CONN_ERROR and schedules the shutdown work asynchronously. Use
it here as well.
Fixes: f147dd9eca ("RDS/IB: Disallow connections less than RDS 3.1")
Reported-by: TencentOS Corvus AI <corvus@tencent.com>
Cc: stable@vger.kernel.org
Reviewed-by: Allison Henderson <achender@kernel.org>
Signed-off-by: Aohan Mei <henrymei@tencent.com>
Link: https://patch.msgid.link/20260911073436.3542080-1-ljp1205831794@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=H3Kp
-----END PGP SIGNATURE-----
Merge tag 'nf-26-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Fix KMSAN reports an uninit-value in nf_nat_setup_info() for netmap,
from Theodor Arsenij Larionov Trichkine.
2) Restrict deletion of netdevice in basechain and flowtable to exact
matching only, from Fernando F. Mancera.
3) Fix nf_nat_register_fn() error path allowing for a memleak.
4) Hold reference on ct until flow is released to address, otherwise
access to release ct->ext or different ct due to typesafe RCU
semantics.
* tag 'nf-26-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: flowtable: hold reference on ct until flow is released
netfilter: nf_nat: unregister and release hooks on error
netfilter: nf_tables: fix device name and prefix match in hook lookup
netfilter: nft_nat: fully initialise new_addr in netmap setup
====================
Link: https://patch.msgid.link/20260913205447.1889203-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kuniyuki Iwashima says:
====================
neighbour: Small fixes for RTM_{GET,SET}NEIGHTBL.
While working on the follow-up suggested here,
https://lore.kernel.org/20260902143023.GA3966681@shredder
I found a few bugs in RTM_GETNEIGHTBL and RTM_SETNEIGHTBL,
which this series fixes.
Patch 1, 3, 4 will conflict with net-next in neightbl_dump_info()
due to removal of net_eq() below:
p = list_next_entry(&tbl->parms, list);
list_for_each_entry_from_rcu(p, &tbl->parms_list, list) {
if (!net_eq(neigh_parms_net(p), net))
continue;
Note also that currently neigh_proc_dointvec_ms_jiffies_positive()
is buggy and does not enforce min/max, and it needs this fix:
https://lore.kernel.org/20260905233819.1064529-2-kuniyu@google.com
====================
Link: https://patch.msgid.link/20260909233143.2401847-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
neightbl_dump_info() calls neightbl_fill_info() in each loop
to render the default parms.
If there are many devices and neightbl_fill_param_info() failed,
neightbl_fill_info() is called again when the dump resumes:
# ynl --family rt-neigh --dump getneightbl --output-json |
jq '.[] | {name: .name, ifindex: .parms.ifindex}'
...
{
"name": "ndisc_cache",
"ifindex": null
}
...
{
"name": "ndisc_cache",
"ifindex": 6
}
{
"name": "ndisc_cache",
"ifindex": null
}
{
"name": "ndisc_cache",
"ifindex": 5
}
Let's skip neightbl_fill_info() if it is already called in
neightbl_dump_info().
Note that we cannot use !neigh_skip instead of !default_skip
because default_skip == 1 && neigh_skip == 0 could be true
if the first neightbl_fill_param_info() fails.
Also, nidx must be cleared at the end of each table loop;
otherwise, if neightbl_fill_info() for a subsequent table
fails, the leftover nidx from the previous table would be
saved in cb->args[1], resulting in erroneously skipping parms
of the subsequent table in the next dump.
Fixes: c7fb64db00 ("[NETLINK]: Neighbour table configuration and statistics via rtnetlink")
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260909233143.2401847-5-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commits started to initialise blackhole_netdev with
neigh_parms_alloc().
This is visible in init_net as the ifindex==0 entries via
RTM_GETNEIGHTBL:
# ynl --family rt-neigh --dump getneightbl --output-json \
| jq '.[] | select(.parms.ifindex == 0)
| {name: .name, ifindex: .parms.ifindex}'
{
"name": "arp_cache",
"ifindex": 0
}
{
"name": "ndisc_cache",
"ifindex": 0
}
For RTM_SETNEIGHTBL, ifindex being 0 means wildcard.
Let's skip blackhole_netdev's parms in neightbl_dump_info().
Note that lookup_neigh_parms() does not need the same change
because the default parms is always the first entry and matches
with ifindex == 0.
Fixes: e5f80fcf86 ("ipv6: give an IPv6 dev to blackhole_netdev")
Fixes: 22600596b6 ("ipv4: give an IPv4 dev to blackhole_netdev")
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260909233143.2401847-4-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NDTPA_INTERVAL_PROBE_TIME_MS sets .type and .min but misses
.validation_type, so no validation is applied:
# ynl --family rt-neigh --do setneightbl \
--json '{"name": "arp_cache", "parms": {"interval-probe-time-ms": 0}}'
# ynl --family rt-neigh --dump getneightbl --output-json | \
jq '.[] | select(.name == "arp_cache" and has("config"))
| .parms["interval-probe-time-ms"]'
0
Moreover, nla_get_msecs() uses msecs_to_jiffies(), and u64 is
silently cast to u32, so a larger value can bypass the min check:
e.g. 4294967296 == 0x100000000
# ynl --family rt-neigh --do setneightbl \
--json '{"name": "arp_cache", "parms": {"interval-probe-time-ms": 4294967296}}'
# ynl --family rt-neigh --dump getneightbl --output-json | \
jq '.[] | select(.name == "arp_cache" and has("config"))
| .parms["interval-probe-time-ms"]'
0
msecs_to_jiffies() returns MAX_JIFFY_OFFSET if the value is
larger than INT_MAX. Also, INT_MAX ms overflows int NEIGH_VAR()
when HZ > 1000 (Alpha, MIPS), and passing a negative integer to
queue_delayed_work(unsigned long delay) causes sign extension,
which wraps around the expiry time to the past, resulting in it
being handled as 0 delay in the timer wheel.
Let's use NLA_POLICY_FULL_RANGE() and limit the max to 1 day.
The same max check is applied to sysctl as well.
Note that this controls the probe interval for NTF_MANAGED
entries, so the max of 1 day is unlikely to break any
deployments.
Fixes: 211da42eaa ("net, neigh: introduce interval_probe_time_ms for periodic probe")
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260909233143.2401847-3-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
neightbl_dump_info() fetches the first non-default neigh_parms
with list_next_entry(&tbl->parms, ...) and iterates through the
list with list_for_each_entry_from_rcu().
However, list_next_entry() does not use RCU helper.
Let's use list_for_each_entry_rcu() and skip the default parms.
Fixes: 4ae34be500 ("neighbour: Convert RTM_GETNEIGHTBL to RCU.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260909233143.2401847-2-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nf_ct_put() releases the ct->ext area inmediately, the rcu typesafe
semantics also allow to refer to the wrong conntrack from the flowtable
datapath. Hold reference on ct until flow is released after rcu grace
period.
Add rcu_barrier() on module exit path, to ensure pending flow entries
are release before module goes away.
Fixes: 0ff90b6c20 ("netfilter: nf_flow_offload: fix use-after-free and a resource leak")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If nf_hook_entries_insert_raw() fails, the NAT hooks get never released,
resulting in a memleak.
Postpone setting nat_proto_net->nat_hook_ops when the hooks are
registered to simplify the error path to decide whether the nat hooks
need unwinding.
Fixes: 1cd472bf03 ("netfilter: nf_nat: add nat hook register functions to nf_nat")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, a netdev chain or flowtable hooked to a device prefix can be
unintentionally deleted by a control-plane request targeting an exact
device name or even a shorter one due to the usage of min() to calculate
the length to match.
Fix this by making sure an exact device match never matches a prefix and
that both the target and the candidate have the same length during
delete operation. The add and update paths retain the existing overlap
matching to prevent a single device from matching multiple hooks.
Reported-by: Wei Fang <void0red@gmail.com>
Closes: https://lore.kernel.org/netfilter-devel/CANE+tVrDeNCHQVmsqkV2ozeBqyE3GtRDMhZgsg1bhw10yGNTRQ@mail.gmail.com/
Fixes: 6d07a28950 ("netfilter: nf_tables: Support wildcard netdev hook specs")
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nft_nat_setup_netmap() builds the mapped address in an on-stack
union nf_inet_addr. For an IPv4 mapping it writes only the 4-byte .ip
member and the loop runs a single 32-bit iteration, but it then copies
the whole 16-byte union into range->min_addr and range->max_addr, so the
upper 12 bytes reach nf_nat_setup_info() uninitialised.
KMSAN reports an uninit-value in nf_nat_setup_info() reached from
nft_nat_eval(). The IPv6 path fills all 16 bytes and is not affected.
Zero-initialise new_addr.
Fixes: 3ff7ddb135 ("netfilter: nft_nat: add netmap support")
Signed-off-by: Theodor Arsenij Larionov Trichkine <theodorlarionov@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Including fixes from Netfilter, Bluetooth and WPAN.
Current release - new code bugs:
- Bluetooth: hci_sync: fix not setting CE length properly
- eth: enic: match mailbox replies to request numbers
Previous releases - regressions:
- tunnels: drop stale dst when building an ICMP error for PMTUD
- ipv6: null-check fib6_node before accessing in __ip6_del_rt_siblings()
(bug in the rtnl_lock -> RCU conversion)
- eth: bnxt_en: fix crashes on Thor2 due to OOB coalescing buffer accesses
- eth: bnxt_en: prevent queue stop with deferred completions
Previous releases - always broken:
- eth: ice: don't dereference pointers from TP_printk()
- eth: fix OOB writes on ethtool flow rule dump in 3 drivers
- eth: mlx5: fix FEC configuration with RS_544_514_INTERLEAVED_QUAD
- dsa: tag_brcm: legacy FCS: request needed tailroom
Misc:
- net: cap tx_queue_len at S16_MAX to prevent oversized ring alloc
- ipv6: flowlabel: cap duplicate leases per socket
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=f9J9
-----END PGP SIGNATURE-----
Merge tag 'net-7.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Nothing too exciting, usual stream of fixes. Including fixes from
Netfilter, Bluetooth and WPAN.
Current release - new code bugs:
- Bluetooth: hci_sync: fix not setting CE length properly
- eth: enic: match mailbox replies to request numbers
Previous releases - regressions:
- tunnels: drop stale dst when building an ICMP error for PMTUD
- ipv6: null-check fib6_node before accessing in __ip6_del_rt_siblings()
(bug in the rtnl_lock -> RCU conversion)
- eth: bnxt_en:
- fix crashes on Thor2 due to OOB coalescing buffer accesses
- prevent queue stop with deferred completions
Previous releases - always broken:
- eth:
- ice: don't dereference pointers from TP_printk()
- fix OOB writes on ethtool flow rule dump in 3 drivers
- mlx5: fix FEC configuration with RS_544_514_INTERLEAVED_QUAD
- dsa: tag_brcm: legacy FCS: request needed tailroom
Misc:
- net: cap tx_queue_len at S16_MAX to prevent oversized ring alloc
- ipv6: flowlabel: cap duplicate leases per socket"
* tag 'net-7.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (164 commits)
selftests: tc-testing: test action batch failure cleanup
net/sched: act_api: release all action references on NEWACTION failure
openvswitch: fix wrong flag value in get_ipv6_ext_hdrs()
ipmr: account multicast table and route memory
net: phy: dp83td510: handle the active-high LED polarity mode
net: macb: initialize PTP state before registering clock
net: hsr: enable promiscuous mode on interlink port with fwd offload
ipv6: fix fib6 walker UAF on seq stop
net: stmmac: fix TX descriptor availability check for TSO traffic
net/rds: fix tcp stream corruption with large pages
net: mana: restore the XDP program pointer when pre-allocation fails
net: phy: dp83867: handle the active-high LED polarity mode
octeontx2-af: fix PF/CGX debugfs PCI bus lookup
net: net_failover: Fix the deadlock in net_failover_slave_name_change()
net: phy: mediatek-ge: disable EEE on the MT7530 PHY
tcp: reject non zerocopy devmem tx
net: ethernet: mtk_eth_soc: populate lpi_interfaces to fix EEE support
net: dsa: mt7530: populate lpi_interfaces to fix EEE support
net: hinic: fix mailbox segment buffer overflow
net: sun4i-emac: fix missing of_node_put() for phy_node
...
A batch of bug fixes for the smb client:
- File type corruption fixes in reparse point handling: setting S_IFMT
bits without clearing the existing type first corrupted the file mode
(e.g. S_IFREG | S_IFCHR == S_IFLNK). Fixed in the WSL, POSIX and
native symlink reparse parsers. Also fixes an uninitialized SID
structure in the POSIX readdir path when parsing fails.
- Ownership mapping fixes: forceuid/forcegid mount options were
ignored in several code paths (SID-to-id mapping, WSL extended
attributes, POSIX extensions getattr), allowing an untrusted server
to dictate local file ownership despite explicit mount overrides.
- Heap overflow and overflow fixes in DACL rewriting: replacing short
SIDs with long ones could overflow the DACL buffer, and the u16
accumulator for DACL size could wrap around with enough ACEs.
- Reference count leak fixes in oplock break and deferred close:
duplicate oplock breaks on a queued work item leaked a
cifsFileInfo reference, and deferred close had a similar leak when
requeueing a running work item. Both cause busy-inode oopses on
unmount.
- DFS superblock use-after-free fix: the iterator callback stored a
raw superblock pointer without pinning it, racing with automount
expiry.
- One-byte slab OOB read in the native symlink parser when handling
share-root relative paths.
- Hardening of legacy SMB1 input: reject userspace-crafted
cifs.idmap key descriptions that bypass kernel origin checks, and
validate DataOffset in CIFSSMBRead() to prevent heap info
disclosure from a malicious server.
- DFS cache fix: defer metadata updates until target copying
succeeds to prevent partial-state cache entries on allocation
failure.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTcqRusfSdYROJQwGkpVtNKoQNdYwUCaqLMxAAKCRApVtNKoQNd
YwSyAQDUDSxCnDMmJbRr4e22oF/YrGSN/snp8cqrZlZh2pb5/gD/c2G3xMJA85YP
yL/G8auRWkpwDl0/Parqptjhx1c9YwE=
=PjPM
-----END PGP SIGNATURE-----
Merge tag 'cifs-fixes-7.3-rc3' of https://git.manguebit.org/linux
Pull smb client fixes from Paulo Alcantara:
- File type corruption fixes in reparse point handling: setting S_IFMT
bits without clearing the existing type first corrupted the file mode
(e.g. S_IFREG | S_IFCHR == S_IFLNK). Fixed in the WSL, POSIX and
native symlink reparse parsers. Also fixes an uninitialized SID
structure in the POSIX readdir path when parsing fails.
- Ownership mapping fixes: forceuid/forcegid mount options were
ignored in several code paths (SID-to-id mapping, WSL extended
attributes, POSIX extensions getattr), allowing an untrusted server
to dictate local file ownership despite explicit mount overrides.
- Heap overflow and overflow fixes in DACL rewriting: replacing short
SIDs with long ones could overflow the DACL buffer, and the u16
accumulator for DACL size could wrap around with enough ACEs.
- Reference count leak fixes in oplock break and deferred close:
duplicate oplock breaks on a queued work item leaked a
cifsFileInfo reference, and deferred close had a similar leak when
requeueing a running work item. Both cause busy-inode oopses on
unmount.
- DFS superblock use-after-free fix: the iterator callback stored a
raw superblock pointer without pinning it, racing with automount
expiry.
- One-byte slab OOB read in the native symlink parser when handling
share-root relative paths.
- Hardening of legacy SMB1 input: reject userspace-crafted
cifs.idmap key descriptions that bypass kernel origin checks, and
validate DataOffset in CIFSSMBRead() to prevent heap info
disclosure from a malicious server.
- DFS cache fix: defer metadata updates until target copying
succeeds to prevent partial-state cache entries on allocation
failure.
* tag 'cifs-fixes-7.3-rc3' of https://git.manguebit.org/linux:
smb: client: fix one-byte OOB read in smb2_parse_native_symlink()
smb: client: fail DACL rewrite when the new DACL exceeds 64K
smb: client: fix heap overflow in DACL owner/group rewrite
smb: client: fix file type corruption in cifs_reparse_point_to_fattr()
smb: client: fix file type corruption in posix_reparse_to_fattr()
smb: client: fix file type corruption in wsl_to_fattr()
smb: client: avoid using uninitialized SIDs in cifs_posix_to_fattr()
smb: client: fix WSL reparse point uid/gid override
smb: client: honor forceuid/forcegid when mapping SIDs to uid/gid
smb: client: fix uid/gid override in getattr with posix extensions
smb: client: fix cifsFileInfo reference leak in deferred close
smb: client: avoid leaking refcount when cifs_sb_tlink() fails
smb: client: avoid leaking refcount in cifs_queue_oplock_break()
smb: client: fill cache fields after populating cache in copy_ref_data()
smb: client: pin DFS superblock in iterator callback
smb: client: reject userspace cifs.idmap descriptions
smb: client: reject out-of-bounds DataOffset in CIFSSMBRead()
smb: client: reject short READ responses in CIFSSMBRead()
* Replace CONFIG_PROC_SYSCTL with CONFIG_SYSCTL
CONFIG_SYSCTL is the config string that controls sysctl subsys.
* Testing
Ran through x86_64 selftest. Skipped linux-next for this trivial fix.
-----BEGIN PGP SIGNATURE-----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=y3Vr
-----END PGP SIGNATURE-----
Merge tag 'sysctl-7.03-fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl
Pull sysctl fix from Joel Granados:
"This fell through the cracks during the latest merge window. There are
no more CONFIG_PROC_SYSCTL uses after this fix:
- Replace CONFIG_PROC_SYSCTL with CONFIG_SYSCTL
CONFIG_SYSCTL is the config string that controls sysctl subsys"
* tag 'sysctl-7.03-fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl:
syscall_user_dispatch: Use CONFIG_SYSCTL for sysctl guard
* core: Do not start hrtimer when pretimeout is zero
* msc313e: Various fixes for issues reported by Sashiko
* MAINTAINERS: Update URI for watchdog tree
* sunxi_wdt: preserve boot-enabled watchdog
-----BEGIN PGP SIGNATURE-----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=qPpk
-----END PGP SIGNATURE-----
Merge tag 'watchdog-for-v7.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull watchdog fixes from Guenter Roeck:
- core: Do not start hrtimer when pretimeout is zero
- msc313e: Various fixes for issues reported by Sashiko
- MAINTAINERS: Update URI for watchdog tree
- sunxi_wdt: preserve boot-enabled watchdog
* tag 'watchdog-for-v7.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
watchdog: msc313e: Sync timeout value if WDT was running at boot
watchdog: msc313e: Fix undefined behavior
watchdog: msc313e: Fix spurious reset on suspend
watchdog: msc313e: Enable clock before accessing hardware registers
watchdog: msc313e: Fix clock leak and spurious timer in settimeout()
watchdog: msc313e: Avoid division by zero
watchdog: fix hrtimer start when pretimeout is zero
MAINTAINERS: Update URI for watchdog tree
watchdog: msc313e: Fix NULL pointer dereference in PM callbacks
watchdog: sunxi_wdt: preserve boot-enabled watchdog
Xuanqiang Luo says:
====================
net/sched: fix action batch failure cleanup
Failed batched RTM_NEWACTION requests can leak action references and
reserved IDR indices when cleanup encounters a filter-bound action.
Patch 1 fixes the failure cleanup.
Patch 2 adds tc-testing regression coverage.
Failure reproduction (key output excerpts):
python3 tdc.py -f tc-tests/actions/gact-rollback.json
not ok 1 e3b1 - Failed action batch releases a bound action reference
Could not match regex pattern. Verify command output:
[...]
index 1 ref 3 bind 1
not ok 2 e3b2 - Failed action batch releases entries after a bound action
Command exited with 255, expected 0
RTNETLINK answers: Resource temporarily unavailable
We have an error talking to the kernel
not ok 3 e3b3 - Failed action batch releases repeated references to a bound action
Could not match regex pattern. Verify command output:
[...]
index 1 ref 4 bind 1
====================
Link: https://patch.msgid.link/20260909070336.32979-1-xuanqiang.luo@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add tests for cleanup after a batched RTM_NEWACTION request fails.
Replace an existing gact action bound to a filter, then fail a later
entry by requesting goto chain without a classifier context.
Check that the bound action's reference count returns to its original
value. Also cover a successfully initialized new action between the
bound action and the failing entry, verifying that its reserved index
can be reused. Repeat the bound action in another batch to check that
each temporary reference to the same action is released.
Signed-off-by: Xuanqiang Luo <luoxuanqiang@kylinos.cn>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260909070336.32979-3-xuanqiang.luo@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a batched RTM_NEWACTION request replaces an existing action,
tcf_idr_check_alloc() takes a temporary reference on it. If a later
action fails to initialize, tcf_action_destroy() uses strict release
semantics to clean up the actions initialized so far. For an action
bound to a filter, the strict check returns -EPERM without dropping
the temporary reference.
This error also makes tcf_action_destroy() return before releasing
subsequent entries. Any new action initialized between the bound
action and the failing entry is leaked together with its reserved
IDR slot, preventing reuse of its index.
Use tcf_idr_release() to drop each reference held by the batch without
rejecting bound actions. This allows cleanup to continue through all
initialized entries and preserves the module reference release when
an action is destroyed. Explicit action deletion and flushing retain
their separate bind-count checks.
Fixes: 55334a5db5 ("net_sched: act: refuse to remove bound action outside")
Cc: stable@vger.kernel.org
Signed-off-by: Xuanqiang Luo <luoxuanqiang@kylinos.cn>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260909070336.32979-2-xuanqiang.luo@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-09-08 (idpf, ice)
For idpf:
Myeonghun Pak adds calls to disable DIM work and PTM to allow for proper
cleanup.
Josh adds check, and adjustment, for VLAN headers when processing RSC
packets.
For ice:
Jake adds call to xa_destroy for xarray sched_node_ids; also moving it
from port_info struct to ice_hw to simplify its lifecycle management.
Jakub Kicinski stores trace event data as scalars instead of
dereferencing pointers in TP_printk(), preventing use-after-free issues
during event printing and eliminating double-dereference warnings.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
eth: ice: don't dereference pointers from TP_printk()
ice: add missing xa_destroy for sched_node_ids
idpf: account for VLAN header when parsing RSC packet header
idpf: disable PTM on probe failure and on remove
idpf: disable DIM work before freeing q_vectors
====================
Link: https://patch.msgid.link/20260908214502.528440-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ESP and AH cases in get_ipv6_ext_hdrs() used IPPROTO_FRAGMENT instead
of OFPIEH12_FRAG when checking for out-of-order extension headers, causing
the fragment header to not be recognised as a valid predecessor.
The original code used IPPROTO_FRAGMENT (44) as a bitmask constant where
OFPIEH12_FRAG (1 << 4 = 16) was intended. IPPROTO_FRAGMENT encodes bits
2, 3 and 5 (OFPIEH12_AUTH | OFPIEH12_DEST | OFPIEH12_ROUTER), but not
bit 4 (OFPIEH12_FRAG). This caused incorrect OFPIEH12_UNSEQ verdicts in
both the ESP and AH arms: the ESP arm failed to whitelist OFPIEH12_FRAG,
while the AH arm accidentally whitelisted OFPIEH12_AUTH.
With the fix, a packet with two AH headers now also gets OFPIEH12_UNSEQ
in addition to OFPIEH12_UNREP, matching the ESP arm which already sets
UNSEQ on a repeat, which is the intended behavior.
Fixes: 28a3f06017 ("net: openvswitch: IPv6: Add IPv6 extension header support")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://patch.msgid.link/1b1582eb07550d71f3cbe210e5cb31eeb8d0ad86.1788876917.git.echaudro@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A netadmin in a user+net namespace can create many IPv4 and IPv6
multicast routing tables with MRT_TABLE and MRT6_TABLE. Each unseen
id allocates an mr_table via the shared mr_table_alloc(), links it
into the per-net list, and leaves it until netns teardown. Those
objects were not charged to memcg, so the host unreclaimable slab
grows with the table count.
Account mr_table allocations with GFP_KERNEL_ACCOUNT and mark the
IPv4/IPv6 MFC caches SLAB_ACCOUNT. This matches the established
handling of IP addresses, routes and alternate interface names.
Unresolved MFC entries are still allocated from softIRQ with
GFP_ATOMIC and are not charged. They expire after 10 seconds and are
bounded by the socket receive queue; see commit 0079ad8e8d
("ipmr: remove hard code cache_resolve_queue_len limit").
Fixes: f0ad0860d0 ("ipv4: ipmr: support multiple tables")
Fixes: d1db275dd3 ("ipv6: ip6mr: support multiple tables")
Cc: stable@vger.kernel.org
Reported-by: Vega <vega@nebusec.ai>
Signed-off-by: Zihan Xi <zihanx@nebusec.ai>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/050b58f7fc6b45da0fb12768ebb62d18fa46133d.1788784801.git.zihanx@nebusec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dp83td510_led_polarity_set() only recognizes PHY_LED_ACTIVE_LOW, so
PHY_LED_ACTIVE_HIGH falls through to the default case and returns -EINVAL.
of_phy_led() propagates the error, of_phy_leds() drops the LEDs registered
so far and passes it on, and phy_probe() returns it. A device tree marking
a DP83TD510 LED as 'active-high', which leds/common.yaml allows and
ethernet-phy.yaml references for led@N nodes, thus leaves the mdio device
unbound, so phy_attach_direct() falls back to the genphy driver, which
cannot drive this 10BASE-T1L single-mode PHY, so the interface has no
usable link.
The callback initializes polarity to DP83TD510E_LED_POLARITY(index), which
is the active-high setting, so the request is already satisfied and only
the case label is missing.
Cc: stable@vger.kernel.org
Fixes: 5b281fe7e3 ("net: phy: dp83td510: introduce LED framework support")
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260908105959.70453-3-donggeunyoo.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gem_ptp_init() registers the PTP clock before initializing
bp->tsu_clk_lock and the TSU hardware. Since ptp_clock_register()
publishes the PTP character device, userspace may invoke PTP callbacks
before the lock and hardware are ready.
In addition, gem_ptp_init() is called from both the interface open and
resume paths. Reinitializing tsu_clk_lock there can reset the lock while
timestamp processing is using it.
This race is theoretical and has not been observed in practice.
Initialize tsu_clk_lock once during probe and initialize the TSU before
registering the PTP clock.
Fixes: ab91f0a9b5 ("net: macb: Add hardware PTP support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/netdev/20260904030439.3994047-1-runyu.xiao@seu.edu.cn/
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Link: https://patch.msgid.link/20260908103924.607033-1-runyu.xiao@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
