System errors can sometimes cause multiple errors to be reported
to the TX reporter at the same time. For instance, lost interrupts
may cause several SQs to time out simultaneously. When dev_watchdog
notifies the driver for that, it iterates over all SQs to trigger
recovery for the timed-out ones, via TX health reporter.
However, grace period allows only one recovery at a time, so only
the first SQ recovers while others remain blocked. Since no further
recoveries are allowed during the grace period, subsequent errors
cause the reporter to enter an ERROR state, requiring manual
intervention.
To address this, set the TX reporter's default burst period
to 0.5 second. This allows the reporter to detect and handle all
timed-out SQs within this window before initiating the grace period.
To account for the possibility of a similar issue in the RX reporter,
its default burst period is also configured.
Additionally, while here, align the TX definition prefix with the RX,
as these are used only in EN driver.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250824084354.533182-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable configuration of the burst period — a time window starting
from the first error recovery, during which the reporter allows
recovery attempts for each reported error.
This feature is helpful when a single underlying issue causes multiple
errors, as it delays the start of the grace period to allow sufficient
time for recovering all related errors. For example, if multiple TX
queues time out simultaneously, a sufficient burst period could allow
all affected TX queues to be recovered within that window. Without this
period, only the first TX queue that reports a timeout will undergo
recovery, while the remaining TX queues will be blocked once the grace
period begins.
Configuration example:
$ devlink health set pci/0000:00:09.0 reporter tx burst_period 500
Configuration example with ynl:
./tools/net/ynl/pyynl/cli.py \
--spec Documentation/netlink/specs/devlink.yaml \
--do health-reporter-set --json '{
"bus-name": "auxiliary",
"dev-name": "mlx5_core.eth.0",
"port-index": 65535,
"health-reporter-name": "tx",
"health-reporter-burst-period": 500
}'
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250824084354.533182-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the devlink health reporter starts the grace period
immediately after handling an error, blocking any further recoveries
until it finished.
However, when a single root cause triggers multiple errors in a short
time frame, it is desirable to treat them as a bulk of errors and to
allow their recoveries, avoiding premature blocking of subsequent
related errors, and reducing the risk of inconsistent or incomplete
error handling.
To address this, introduce a configurable burst period for devlink
health reporter. Start this period when the first error is handled,
and allow recovery attempts for reported errors during this window.
Once burst period expires, begin the grace period to block further
recoveries until it concludes.
Timeline summary:
----|--------|------------------------------/----------------------/--
error is error is burst period grace period
reported recovered (recoveries allowed) (recoveries blocked)
For calculating the burst period duration, use the same
last_recovery_ts as the grace period. Update it on recovery only
when the burst period is inactive (either disabled or at the
first error).
This patch implements the framework for the burst period and
effectively sets its value to 0 at reporter creation, so the current
behavior remains unchanged, which ensures backward compatibility.
A downstream patch will make the burst period configurable.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250824084354.533182-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract the health reporter recovery abort logic into a separate
function devlink_health_recover_abort().
The function encapsulates the conditions for aborting recovery:
- When auto-recovery is disabled
- When previous error wasn't recovered
- When within the grace period after last recovery
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250824084354.533182-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the default graceful period from a parameter to
devlink_health_reporter_create() to a field in the
devlink_health_reporter_ops structure.
This change improves consistency, as the graceful period is inherently
tied to the reporter's behavior and recovery policy. It simplifies the
signature of devlink_health_reporter_create() and its internal helper
functions. It also centralizes the reporter configuration at the ops
structure, preparing the groundwork for a downstream patch that will
introduce a devlink health reporter burst period attribute whose
default value will similarly be provided by the driver via the ops
structure.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250824084354.533182-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fixed_phy_register() creates and registers the phy_device. To be
symmetric, we should not only unregister, but also free the phy_device
in fixed_phy_unregister(). This allows to simplify code in users.
Note wrt of_phy_deregister_fixed_link():
put_device(&phydev->mdio.dev) and phy_device_free(phydev) are identical.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/ad8dda9a-10ed-4060-916b-3f13bdbb899d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have only two users of fixed_phy_add(), both use address 0 and
ignore the return value. So simplify fixed_phy_add() accordingly.
Whilst at it, constify the fixed_phy_status configs.
Note:
fixed_phy_add() is a legacy function which shouldn't be used in new
code, as it's use may be problematic:
- No check whether a fixed phy exists already at the given address
- If fixed_phy_register() is called afterwards by any other driver,
then it will also use phy_addr 0, because fixed_phy_add() ignores
the ida which manages address assignment
Drivers using a fixed phy created by fixed_phy_add() in platform code,
should dynamically create a fixed phy with fixed_phy_register()
instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/762700e5-a0b1-41af-aa03-929822a39475@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As noted in the kernel documentation, open-coded multiplication in
allocator arguments is discouraged because it can lead to integer overflow.
Use devm_kcalloc() to gain built-in overflow protection, making memory
allocation safer when calculating allocation size compared to explicit
multiplication.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250825142753.534509-1-rongqianfeng@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On soft-reboot, with a reset GPIO defined for an Aeonsemi PHY, the
special match_phy_device fails to correctly identify that the PHY
needs to load the firmware again.
This is caused by the fact that PHY ID is read BEFORE the PHY reset
GPIO (if present) is asserted, so we can be in the scenario where the
phydev have the previous PHY ID (with the PHY firmware loaded) but
after reset the generic AS21xxx PHY is present in the PHY ID registers.
To better handle this, skip reading the PHY ID register only for the PHY
that are not AS21xxx (by matching for the Aeonsemi Vendor) and always
read the PHY ID for the other case to handle both firmware already
loaded or an HW reset.
Fixes: 830877d89e ("net: phy: Add support for Aeonsemi AS21xxx PHYs")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250823134431.4854-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce phy_id_compare_vendor() PHY ID helper to compare a PHY ID with
the PHY ID Vendor using the generic PHY ID Vendor mask.
While at it also rework the PHY_ID_MATCH macro and move the mask to
dedicated define so that PHY driver can make use of the mask if needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250823134431.4854-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
POWER8 support a maximum of 16 subcrq indirect descriptor entries per
H_SEND_SUB_CRQ_INDIRECT call, while POWER9 and newer hypervisors
support up to 128 entries. Increasing the max number of indirect
descriptor entries improves batching efficiency and reduces
hcall overhead, which enhances throughput under large workload on POWER9+.
Currently, ibmvnic driver always uses a fixed number of max indirect
descriptor entries (16). send_subcrq_indirect() treats all hypervisor
errors the same:
- Cleanup and Drop the entire batch of descriptors.
- Return an error to the caller.
- Rely on TCP/IP retransmissions to recover.
- If the hypervisor returns H_PARAMETER (e.g., because 128
entries are not supported on POWER8), the driver will continue
to drop batches, resulting in unnecessary packet loss.
In this patch:
Raise the default maximum indirect entries to 128 to improve ibmvnic
batching on morden platform. But also gracefully fall back to
16 entries for Power 8 systems.
Since there is no VIO interface to query the hypervisor’s supported
limit, vnic handles send_subcrq_indirect() H_PARAMETER errors:
- On first H_PARAMETER failure, log the failure context
- Reduce max_indirect_entries to 16 and allow the single batch to drop.
- Subsequent calls automatically use the correct lower limit,
avoiding repeated drops.
The goal is to optimizes performance on modern systems while handles
falling back for older POWER8 hypervisors.
Performance shows 40% improvements with MTU (1500) on largework load.
Signed-off-by: Mingming Cao <mmc@linux.ibm.com>
Reviewed-by: Brian King <bjking1@linux.ibm.com>
Reviewed-by: Haren Myneni <haren@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250821130215.97960-1-mmc@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
state->an_enabled was removed by
commit 4ee9b0dcf0 ("net: phylink: remove an_enabled")
but is left in mac_config() doc, so clean it.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250824013009.2443580-1-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_diag_dump() / tcp_diag_dump_one() is just a wrapper of
inet_diag_dump_icsk() / inet_diag_dump_one_icsk(), respectively.
Let's inline them in tcp_diag.c and move static callees as well.
Note that inet_sk_attr_size() is merged into tcp_diag_get_aux_size(),
and we remove inet_diag_handler.idiag_get_aux_size() accordingly.
While at it, BUG_ON() is replaced with DEBUG_NET_WARN_ON_ONCE().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250822190803.540788-7-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These inet_diag functions required struct inet_hashinfo because
they are shared by TCP and DCCP:
* inet_diag_dump_icsk()
* inet_diag_dump_one_icsk()
* inet_diag_find_one_icsk()
DCCP has gone, and we don't need to pass hashinfo down to them.
Let's fetch net->ipv4.tcp_death_row.hashinfo directly in the first
2 functions.
Note that inet_diag_find_one_icsk() don't need hashinfo since the
previous patch.
We will move TCP-specific functions to tcp_diag.c in the next patch.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250822190803.540788-6-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These socket lookup functions required struct inet_hashinfo because
they are shared by TCP and DCCP.
* __inet_lookup_established()
* __inet_lookup_listener()
* __inet6_lookup_established()
* inet6_lookup_listener()
DCCP has gone, and we don't need to pass hashinfo down to them.
Let's fetch net->ipv4.tcp_death_row.hashinfo directly in the above
4 functions.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250822190803.540788-5-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 6c886db2e7 ("net: remove duplicate sk_lookup helpers")
started to check if hashinfo == net->ipv4.tcp_death_row.hashinfo
in __inet_lookup_listener() and inet6_lookup_listener() and
stopped invoking BPF sk_lookup prog for DCCP.
DCCP has gone and the condition is always true.
Let's remove the hashinfo test.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250822190803.540788-4-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since DCCP has been removed, sk->sk_prot->twsk_prot->twsk_destructor
is always tcp_twsk_destructor().
Let's call tcp_twsk_destructor() directly in inet_twsk_free() and
remove ->twsk_destructor().
While at it, tcp_twsk_destructor() is un-exported.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250822190803.540788-3-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 383eed2de5 ("tcp: get rid of twsk_unique()") added
sk->sk_protocol test in __inet_check_established() and
__inet6_check_established() to remove twsk_unique() and call
tcp_twsk_unique() directly.
DCCP has gone, and the condition is always true.
Let's remove the sk_protocol test.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250822190803.540788-2-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export airoha_ppe_check_skb routine in ppe_dev ops. check_skb callback
will be used by the MT76 driver in order to offload the traffic received
by the wlan NIC and forwarded to the ethernet one.
Add rx_wlan parameter to airoha_ppe_check_skb routine signature.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250823-airoha-en7581-wlan-rx-offload-v3-3-f78600ec3ed8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce airoha_ppe_dev struct as container for PPE offload callbacks
consumed by the MT76 driver during flowtable offload for traffic
received by the wlan NIC and forwarded to the wired one.
Add airoha_ppe_setup_tc_block_cb routine to PPE offload ops for MT76
driver.
Rely on airoha_ppe_dev pointer in airoha_ppe_setup_tc_block_cb
signature.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250823-airoha-en7581-wlan-rx-offload-v3-2-f78600ec3ed8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rely on airoha_eth struct in airoha_ppe_flow_offload_cmd routine
signature and in all the called subroutines.
This is a preliminary patch to introduce flowtable offload for traffic
received by the wlan NIC and forwarded to the ethernet one.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250823-airoha-en7581-wlan-rx-offload-v3-1-f78600ec3ed8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add basic support for the MxL86111 PHY which in addition to the features
of the MxL86110 also comes with an SGMII interface.
Setup the interface mode and take care of in-band-an.
Currently only RGMII-to-UTP and SGMII-to-UTP modes are supported while the
PHY would also support RGMII-to-1000Base-X, including automatic selection
of the Fiber or UTP link depending on the presence of a link partner.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/707fd83ec0e11ea620d37f2125a394e9dd1b27fa.1755884175.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .led_hw_control_get and .led_hw_control_set ops are indented with
spaces instead of tabs, unlike the rest of the values of the PHY's
struct phy_driver instance.
Use tabs instead of spaces resulting in a uniform indentation style.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/b9b7336ae309facc5e73874c62e64492fd749cc6.1755884175.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for forcing each connected LED to be always on or always off
by implementing the led_brightness_set() op.
This is done by modifying the COM_EXT_LED_GEN_CFG register to enable
force-mode and forcing the LED either on or off.
When calling the led_hw_control_set() force-mode is again disabled for
that LED.
Implement mxl86110_modify_extended_reg() locked helper instead of
manually acquiring and releasing the MDIO bus lock for single
__mxl86110_modify_extended_reg() calls.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/58eeefc8c24e06cd2110d3cefbd4236b1a4f44a2.1755884175.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In struct channel, the upl lock is implemented using rwlock_t,
protecting access to pch->ppp and pch->bridge.
As previously discussed on the list, using rwlock in the network fast
path is not recommended.
This patch replaces the rwlock with a spinlock for writers, and uses RCU
for readers.
- pch->ppp and pch->bridge are now declared as __rcu pointers.
- Readers use rcu_dereference_bh() under rcu_read_lock_bh().
- Writers use spin_lock() to update.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://patch.msgid.link/20250822012548.6232-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract the same code logic from __ipv6_sock_mc_join() and
ip6_mc_find_dev(), also add new helper ip6_mc_find_idev() to
reduce redundancy and enhance readability.
No functional changes intended.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Link: https://patch.msgid.link/20250822064051.2991480-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Integrate generic net_selftest framework by wiring up
.get_strings, .get_sset_count, and .self_test ethtool ops.
This enables execution of standard self-tests using
`ethtool -t <dev>` on LAN78xx devices.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250822092555.2888870-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
tcp: annotate data-races around icsk_retransmits and icsk_probes_out
icsk->icsk_retransmits is read locklessly from inet_sk_diag_fill(),
tcp_get_timestamping_opt_stats, get_tcp4_sock() and get_tcp6_sock().
icsk->icsk_probes_out is read locklessly from inet_sk_diag_fill(),
get_tcp4_sock() and get_tcp6_sock().
Add corresponding READ_ONCE()/WRITE_ONCE() annotations.
====================
Link: https://patch.msgid.link/20250822091727.835869-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oscar Maes says:
====================
net: ipv4: allow directed broadcast routes to use dst hint
Currently, ip_extract_route_hint uses RTN_BROADCAST to decide
whether to use the route dst hint mechanism.
This check is too strict, as it prevents directed broadcast
routes from using the hint, resulting in poor performance
during bursts of directed broadcast traffic.
This series fixes this, and adds a new selftest to ensure
this does not regress.
Link to v2: https://lore.kernel.org/20250814140309.3742-1-oscmaes92@gmail.com
====================
Link: https://patch.msgid.link/20250819174642.5148-1-oscmaes92@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a test for ensuring that the dst hint mechanism is used for
directed broadcast addresses.
This test relies on mausezahn for sending directed broadcast packets.
Additionally, a high GRO flush timeout is set to ensure that packets
will be received as lists.
The test determines if the hint mechanism was used by checking
the in_brd statistic using lnstat.
Signed-off-by: Oscar Maes <oscmaes92@gmail.com>
Link: https://patch.msgid.link/20250819174642.5148-3-oscmaes92@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, ip_extract_route_hint uses RTN_BROADCAST to decide
whether to use the route dst hint mechanism.
This check is too strict, as it prevents directed broadcast
routes from using the hint, resulting in poor performance
during bursts of directed broadcast traffic.
Fix this in ip_extract_route_hint and modify ip_route_use_hint
to preserve the intended behaviour.
Signed-off-by: Oscar Maes <oscmaes92@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250819174642.5148-2-oscmaes92@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bindings files should not carry markings of editor setup, so drop vim
style annotation. No functional impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://patch.msgid.link/20250821083038.46274-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DTS example in the bindings should be indented with 2- or 4-spaces, so
correct a mixture of different styles to keep consistent 4-spaces.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://patch.msgid.link/20250821083038.46274-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some rtnetlink selftests assume the presence of ifconfig and iproute2
support for the `proto` keyword in `ip address` commands. These
assumptions can cause test failures on modern systems (e.g. Debian
Bookworm) where:
- ifconfig is not installed by default
- The iproute2 version lacks support for address protocol
This patch improves test robustness by:
- Skipping kci_test_promote_secondaries if ifconfig is missing
- Skipping do_test_address_proto if ip address help does not mention
proto
These changes ensure the tests degrade gracefully by reporting SKIP
instead of FAIL when prerequisites are not met, improving portability
across systems.
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Alessandro Ratti <alessandro@0x65c.net>
Link: https://patch.msgid.link/20250822140633.891360-2-alessandro@0x65c.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Golle says:
====================
net: dsa: lantiq_gswip: prepare for supporting new features
Prepare for supporting the newer standalone MaxLinear GSW1xx switch
family by refactoring the existing lantiq_gswip driver.
This is the first of a total of 3 series and doesn't yet introduce
any functional changes, but rather just makes the driver more
flexible, so new hardware and features can be supported in future.
This series has been preceded by an RFC series which covers everything
needed to support the MaxLinear GSW1xx family of switches. Andrew Lunn
had suggested to start with the 8 patches now submitted as they prepare
but don't yet introduce any functional changes.
Everything has been compile and runtime tested on AVM Fritz!Box 7490
(GSWIP version 2.1, VR9 v1.2)
Link: https://lore.kernel.org/aKDhFCNwjDDwRKsI@pidgin.makrotopia.org
====================
Link: https://patch.msgid.link/cover.1755878232.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Store the switch API version in struct gswip_priv. As the hardware has
the 'major/minor' version bytes in the wrong order preventing numerical
comparisons the version to be stored in gswip_priv is constructed in
such a way that the REV field is the most significant byte and the MOD
field the least significant byte. Also provide a conveniance macro to
allow comparing the stored version of the hardware against the already
defined GSWIP_VERSION_* macros.
This is done in order to prepare supporting newer features such as 4096
VLANs and per-port configurable learning which are only available
starting from specific hardware versions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/eddb51ae8d0b2046ca91906e93daad7be5af56d7.1755878232.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While the older Lantiq / Intel which are currently supported all use
the DSA_TAG_GSWIP tagging protocol, newer MaxLinear GSW1xx modules use
another 8-byte tagging protocol. Move the tag protocol information to
struct gswip_hw_info to make it possible for new models to specify
a different tagging protocol.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/841281b62fdb472048fa98fbad6c88dfbf512825.1755878232.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Load microcode as specified in struct hw_info instead of relying on
a single array of instructions. This is done in preparation to allow
loading different microcode for the MaxLinear GSW1xx family.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/486d95c085913d506745fbe4a0ab5d1ebdc3ed63.1755878232.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of relying on hard-coded numbers for MII ports, introduce
a bitmap for MII ports.
This is done in order to prepare for supporting MaxLinear GSW1xx ICs
which got a different layout of ports.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/019fc8ed06f2317976eac143320d1dc046e8f392.1755878232.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce header file and move register definitions as well as the
definitions struct gswip_hw_info and struct gswip_priv there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/551c72c93131cd200b38340741e68ff21793ba0b.1755878232.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MaxLinear GSW1xx series of switches support using either the
(R)(G)MII interface on port 5 or the SGMII interface on port 4 to be
used as CPU port. Prepare for supporting them by defining a mask of
allowed CPU ports instead of a single port.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/879c66672d26fe49c1f5d9aa40d8ebc0f31885ab.1755878232.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The two instances of struct dsa_switch_ops differ only by their
.phylink_get_caps op. Instead of having two instances of dsa_switch_ops,
rather just have a pointer to the phylink_get_caps function in
struct gswip_hw_info.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/03d72eceeb3faecdbe03ce58aab40861cf6b77c1.1755878232.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel tries to be helpful and attach the XDP program in generic
mode if the driver has no BPF ndo at all. Since the xdp.py tests
all have "native" in their names this can be quite confusing.
Force native / "drv" attachment. Note that netdevsim re-uses
the generic handler as its "native" handler, so we'll maintain
the test coverage of the generic mode that way. No need to test
both explicitly, I reckon.
Link: https://patch.msgid.link/20250822195645.1673390-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Aquantia PHY driver consolidation - part 1
This started out as an effort to add some new features hinging on the
VEND1_GLOBAL_CFG_* registers, but I quickly started to notice that the
Aquantia PHY driver has a large code base, but individual PHYs only
implement arbitrary subsets of it.
The table below lists the PHYs known to me to have the
VEND1_GLOBAL_CFG_* registers.
PHY Access from Access from
aqr107_read_rate() aqr113c_fill_interface_modes()
------------------------------------------------------------------
AQR107 y n
AQCS109 y n
AQR111 y n
AQR111B0 y n
AQR112 y n
AQR412 y n
AQR113 y y
AQR113C y y
AQR813 y n
AQR114C y n
AQR115C y y
Maybe you're wondering, after reading this, why don't more Aquantia PHYs
populate phydev->possible_interfaces based on the registers that they
are known to have? And why do AQR114C and AQR115C, PHYs from the same
generation, just having different max speeds, differ in this behaviour?
And why does AQR813, the 8-port variant of AQR113, not call
aqr113c_config_init(), but aqr107_config_init()?
I did wonder, and I don't know either, but I suspect it has to do with
developers not wanting to break what they can't test, and only touching
what they are interested in. Multiplied at a large enough scale, this
tends to result in unmaintainable code.
The tendency might also be encouraged by the slightly strange and
inconsistent naming scheme in this driver.
The set proposes a naming scheme based on generations, and feature
inheritance from Gen X to Gen X+1. This helps fill in missing
software functionalities where the hardware feature should be present.
I had to put a hard stop at 15 patches, so I've picked the more
meaningful functions to consolidate, rather than going through the
entire driver. Depending on review feedback, I can do more or I can
stop.
Furthermore, the set adds generation-appropriate support for two more
PHY IDs: AQR412 and AQR115, and fixes the improper reporting of AQR412C
as AQR412.
The changes were tested on AQR107, AQR112, AQR412C and AQR115.
====================
Link: https://patch.msgid.link/20250821152022.1065237-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
AQR115 is similar to the already supported AQR115C, having speeds up to
2.5Gbps. In fact, the two differ only in the FCBGA package size (7x11mm
vs 7x7mm for the Compact variant). So it makes sense that the feature
set is identical for the 2 drivers.
This PHY is present on the newest PCB revision E (v4.0) of the NXP
LS1046A-RDB, having replaced the RTL8211FS SGMII PHY going to fm1-mac5.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250821152022.1065237-16-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
