iommu_map_sgtable() returns negative error codes on failure, but the
result is stored in an unsigned variable. This prevents proper error
detection.
Change the variable type to ssize_t so negative error values can be
handled correctly.
Fixes: ece3e89809 ("accel/amdxdna: Allow forcing IOVA-based DMA via module parameter")
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/all/adk7kOUBwIyYnX1M@stanley.mountain/
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Wendy Liang <wendy.liang@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260413180238.668441-1-lizhi.hou@amd.com
Convert this driver to DRM_BRIDGE_ATTACH_NO_CONNECTOR and to the
drm_bridge_connector framework which is the current DRM bridge best
practice.
Based on the in-tree dts[i] files this introduces no regression. Based on
the kernel doc of drm_bridge_connector.c:
* To make use of this helper, all bridges in the chain shall report bridge
* operation flags (&drm_bridge->ops) and bridge output type
* (&drm_bridge->type), as well as the DRM_BRIDGE_ATTACH_NO_CONNECTOR attach
* flag (none of the bridges shall create a DRM connector directly).
and each of the 3 LCDIF blocks in the i.MX8MP, all of them comply with the
above requirement:
* For the LCDIF3, the pipeline is:
LCDIF3 -> fsl,imx8mp-hdmi-pvi -> fsl,imx8mp-hdmi-tx -> HDMI connector
And the involved bridges are:
* fsl,imx8mp-hdmi-pvi has ops = 0 (it doesn't set it) because it
implements none the optional features mentioned by those flags, and it
honors the DRM_BRIDGE_ATTACH_NO_CONNECTOR by propagating it
* fsl,imx8mp-hdmi-tx is implemented based on dw-hdmi, which sets ops as
appropriate and also propagates the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag
* display-connector (enabled via the DT overlay if needed) sets ops and
makes DRM_BRIDGE_ATTACH_NO_CONNECTOR mandatory
* The LCDIF2 involves the panel-bridge, display-connector and lvds-decoder
(even though only the pane-bridge is currently supported), and all these
three also set ops as needed and propagate
DRM_BRIDGE_ATTACH_NO_CONNECTOR or make it mandatory.
* The LCDIF1 is used with the adv7511, tc358767 and the panel bridge
drivers which also comply with the requirements.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa8MPxL/MBa8MPxL
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-11-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The imx8mp-hdmi-tx one of many drivers based on dw-hdmi. dw-hdmi in turn
can operate in two different modes, depending on the platform data as set
by the driver:
A. hdmi->plat_data->output_port = 0:
the HDMI output (port@1) in device tree is not used [0]
B. hdmi->plat_data->output_port = 1:
the HDMI output (port@1) is parsed to find the next bridge
The imx8mp-hdmi-tx driver falls in case A. Switching to case B, which is
the current best practice, requires that the HDMI connector is always
described in the live device tree, and a previous commit ensured this is
always the case by adding an overlay in case the device tree does not
comply.
So now we can simply switch to the new mode and support
DRM_BRIDGE_ATTACH_NO_CONNECTOR.
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-10-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Describing the HDMI connector in device tree is recommended. While the
overlay insertion is a workaround to avoid breaking existing devices, every
dts should be improved by adding a connector description.
Add a warning to make users aware as far as possible.
As a warning line cannot hold all the relevant info, add a detailed comment
in the code so it easy to find when the warning is seen.
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-9-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The imx8mp-hdmi-tx is one of many drivers based on dw-hdmi. dw-hdmi in turn
can operate in two different modes, depending on the platform data as set
by the driver:
A. hdmi->plat_data->output_port = 0:
the HDMI output (port@1) in device tree is not used [0]
B. hdmi->plat_data->output_port = 1:
the HDMI output (port@1) is parsed to find the next bridge
The imx8mp-hdmi-tx driver falls in case A. This implies next_bridge will
always be NULL, and so dw_hdmi_bridge_attach() [1] will always fail if
called with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.
In fact case A assumes that DRM_BRIDGE_ATTACH_NO_CONNECTOR is not set and
in that case it adds an HDMI Type A connector programmatically at bridge
attach time.
Support for DRM_BRIDGE_ATTACH_NO_CONNECTOR is implemented by dw-hdmi.c in
case B. However switching to base B requires that port@1 is connected to a
"next bridge" DT node, typically the HDMI connector, because dw-hdmi won't
add the connector when using DRM_BRIDGE_ATTACH_NO_CONNECTOR.
Many dts files for imx8mp-based boards in the kernel have such a connector
described and linked to port@1, so the pipeline will be fully attached up
to a display-connector and a drm_connector added by the
bridge-connector. Sadly some of those dts files don't have the connector
described. Adding it would solve the problem easily, but this would break
existing devices which do not update the dtb when upgrading to a newer
kernel.
In preparation for switching to case B while preserving backward
compatibility for such devices, introduce a module adding the
hdmi-connector node to the live device tree at init time. This will allow
the dw-hdmi code to find the next bridge (the one wrapping the
hdmi-connector) and let the pipeline work as before.
The module is inserted only if there is no endpoint in port@1. So boards
whose device tree describe the connector will not have the device tre
modified, and will start isntantiating the correct HDMI connector type as
described in the device tree.
For boards lacking a connector description in DT the overlay will be added,
abd the HDMI connector will be Type A, which is a reasonable fallback and
is what the driver is currently doing.
[0] https://elixir.bootlin.com/linux/v7.0-rc1/source/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c#L3310
[1] https://elixir.bootlin.com/linux/v7.0-rc1/source/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c#L2907
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-8-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver looks up the next_bridge at probe time and stores it in
hdmi->bridge.next_bridge, but only uses the stored value when attaching,
and only in the DRM_BRIDGE_ATTACH_NO_CONNECTOR case.
This will be problematic with an upcoming change, adding an hdmi-connector
using a device tree overlay when not present. That change is in turn
necessary to migrate the i.MX LCDIF driver to the bridge-connector.
The problem is that, adding the hdmi-connector via an overlay, devlink
considers hdmi-connector a consumer of the dw-hdmi device, generating a
chicken-egg problem:
* hdmi-connector probe won't be tried until dw-hdmi is probed (devlink)
* dw-hdmi probe will defer until it finds the next_bridge (the
hdmi-connector wrapper bridge)
In preparation for those changes, move the next_bridge lookup from probe to
attach, when it is actually used. This allows dw-hdmi to probe, so that the
hdmi-connector can probe as well.
Also avoid storing the pointer in hdmi->bridge.next_bridge: the value is
computed when needed, thus a local variable is enough.
Finally, this also allows to slightly improve the code by not doing any DT
lookup in the !DRM_BRIDGE_ATTACH_NO_CONNECTOR case.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa8MPxL/MBa8MPxL
Acked-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Damon Ding <damon.ding@rock-chips.com> # rk3399
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-7-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
dw-hdmi can operate in two different modes, depending on the platform data
as set by the driver:
A. hdmi->plat_data->output_port = 0:
the HDMI output (port@1) in device tree is not used
B. hdmi->plat_data->output_port = 1:
the HDMI output (port@1) is parsed to find the next bridge
Only case B is supported when the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is
passed to the attach callback. Emit a warning when this is violated. Also
return -EINVAL which would be returned by drm_bridge_attach() right after
anyway.
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa8MPxL/MBa8MPxL
Tested-by: Damon Ding <damon.ding@rock-chips.com> # rk3399
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-6-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The meaning of this flag may not be obvious at first sight.
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa8MPxL/MBa8MPxL
Tested-by: Damon Ding <damon.ding@rock-chips.com> # rk3399
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-5-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The bridge and ret variables are per-iteration variables, whose values
don't have to be carried to the next iteration or be used after the loop
end. Move their declaration inside the loop scope as a cleanup and to make
code clearer.
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-4-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
lcdif_attach_bridge() uses dev_err_probe() in some error paths, dev_err() +
return in others. Use dev_err_probe() for all of them to make code
consistent, simpler and with better error reporting.
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-3-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Putting the remote device_node reference requires a of_node_put(remote) in
two places. Use a cleanup action to simplify the code.
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa8MPxL/MBa8MPxL
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-1-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
A job timeout does not necessarily indicate that the device is hung, as
it may still be processing other jobs.
Track whether any jobs have been successfully submitted or completed,
and use this information to determine if the device is making forward
progress. If so, return DRM_GPU_SCHED_STAT_NO_HANG instead of treating
the timeout as a device hang.
In the meanwhile the timeout interval is changed to 2 seconds which meets
the userspace requirement.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260409175826.195665-1-lizhi.hou@amd.com
In order to unify the handling of the panel and bridge, apply
panel_bridge helpers for Analogix DP driver. With this patch, the
bridge support will also become available.
The following changes have ben made:
- Apply plane_bridge helper to wrap the panel as the bridge.
- Remove the explicit panel APIs calls, which can be replaced with
the automic bridge APIs calls wrapped by the panel.
- Remove the unnecessary analogix_dp_bridge_get_modes().
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-9-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The analogix_dp_unbind() should be balanced with analogix_dp_bind().
There are no bridge enabling and panel preparing in analogix_dp_bind(),
so it should be reasonable to remove the bridge disabing and panel
unpreparing in analogix_dp_unbind().
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-8-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Uniformly, move the next bridge attachment to the Analogix side
rather than scattered on Rockchip and Exynos sides. It can also
help get rid of the callback &analogix_dp_plat_data.attach() and
make codes more concise.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-7-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Apply analogix_dp_finish_probe() in order to move the panel/bridge
parsing from Exynos side to the Analogix side.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-6-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Apply analogix_dp_finish_probe() in order to move the panel/bridge
parsing from Rockchip side to the Analogix side.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-5-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Since the panel/bridge should logically be positioned behind the
Analogix bridge in the display pipeline, it makes sense to handle
the panel/bridge parsing on the Analogix side. Therefore, we add
a new API analogix_dp_finish_probe(), which combines the panel/bridge
parsing with component addition, to do it.
In order to process component binding right after the probe completes,
the &analogix_dp_plat_data.ops is newly added to pass &component_ops,
for which the &dp_aux_ep_device_with_data.done_probing() of DP AUX bus
only supports passing &drm_dp_aux.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-4-damon.ding@rock-chips.com
[Luca: propagate 'depends on OF' to DRM_ANALOGIX_DP and reverse dependencies]
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Initialize bridge_connector for both Rockchip and Exynos encoder sides.
Then, make DRM_BRIDGE_ATTACH_NO_CONNECTOR mandatory for Analogix bridge
side, as the private &drm_connector is no longer created.
The previous &drm_connector_funcs and &drm_connector_helper_funcs APIs
are replaced by the corresponding &drm_bridge_funcs APIs:
analogix_dp_atomic_check() -> analogix_dp_bridge_atomic_check()
analogix_dp_detect() -> analogix_dp_bridge_detect()
analogix_dp_get_modes() -> analogix_dp_bridge_get_modes()
analogix_dp_bridge_edid_read()
Additionally, the compatibilities of Analogix DP bridge based on whether
the next bridge is a 'panel'. If it is, OP_MODES and OP_DETECT are
supported; If not (the next bridge is a 'monitor' or a bridge chip),
OP_EDID and OP_DETECT are supported.
The devm_drm_bridge_add() is placed in analogix_dp_bind() instead of
analogix_dp_probe(), because the type of next bridge (the panel, monitor
or bridge chip) can only be determined after the probe process has fully
completed.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-3-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
To avoid using &analogix_dp_device.connector for compatibility
with the bridge connector framework, get &drm_connector from
&drm_atomic_state instead.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20260413132551.1049307-2-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Replace @dma_addr with @pagemap_addr in the function documentation,
as @pagemap_addr is the actual name of the function argument.
Suggested-by: Francois Dugast <francois.dugast@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://patch.msgid.link/20260410205929.3914474-6-matthew.brost@intel.com
The dma-map IOVA alloc, link, and sync APIs perform significantly better
than dma-map / dma-unmap, as they avoid costly IOMMU synchronizations.
This difference is especially noticeable when mapping a 2MB region in
4KB pages.
Use the IOVA alloc, link, and sync APIs for DRM pagemap, which create DMA
mappings between the CPU and GPU for copying data.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://patch.msgid.link/20260410205929.3914474-5-matthew.brost@intel.com
Split drm_pagemap_migrate_map_pages into device / system helpers clearly
seperating these operations. Will help with upcoming changes to split
IOVA allocation steps.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://patch.msgid.link/20260410205929.3914474-4-matthew.brost@intel.com
All current users of DRM pagemap set source_peer_migrates to true during
migration, and it is unclear whether any user would ever want to disable
this for performance reasons or for features such as compression. It is
also questionable whether this flag could be made to work with
high-speed fabric mapping APIs.
Drop the flag and make DRM pagemap unconditionally assume that
source_peer_migrates is true.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://patch.msgid.link/20260410205929.3914474-3-matthew.brost@intel.com
The dma-map IOVA alloc, link, and sync APIs perform significantly better
than dma-map / dma-unmap, as they avoid costly IOMMU synchronizations.
This difference is especially noticeable when mapping a 2MB region in
4KB pages.
Use the IOVA alloc, link, and sync APIs for GPU SVM, which create DMA
mappings between the CPU and GPU.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patch.msgid.link/20260410205929.3914474-2-matthew.brost@intel.com
drm_connector_attach_hdr_output_metadata_property() always returns zero,
since drm_object_attach_property() returns void. No caller checks the
return value, so change the return type to void.
Also fix a typo in the kerneldoc ("HDR_OUTPUT_METADA" -> "HDR_OUTPUT_METADATA").
Reviewed-by: Melissa Wen <mwen@igalia.com>
Link: https://patch.msgid.link/20260330133446.3265938-2-mcanal@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
The VSP serves as an interface to memory and a compositor to the DU. It
therefore needs to be suspended after and resumed before the DU, to be
properly stopped and restarted in a controlled fashion driven by the DU
driver. This currently works by chance. Avoid relying on luck by
enforcing the correct suspend/resume ordering with device links.
Based on similar work done by Laurent Pinchart for R-Car DU.
commit db5be3a7d6 ("drm: rcar-du: Ensure correct suspend/resume
ordering with VSP")
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260330144651.817338-1-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Commit 3bce3fdd1f ("drm: rcar-du: Don't leak device_link to CMM")
refactored CMM handling, and introduced an incorrect test for CMM
availability. When no CMM is present, the rcrtc->cmm field is NULL,
testing rcrtc->cmm->dev causes a NULL pointer dereference. This slipped
through testing as all tests were run with the CMM present.
Fix this issue by correctly testing for rcrtc->cmm.
Fixes: 3bce3fdd1f ("drm: rcar-du: Don't leak device_link to CMM")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/dri-devel/CAMuHMdXomz9GFDqkBjGX9Sda_GLccPcrihvFbOz0GAitDVNTbw@mail.gmail.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260408124205.1962448-1-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Waveshare have a serie of DSI panel kits with the DPI or LVDS panel
being attached to the DSI2DPI or DSI2LVDS bridge. The commit
46be11b678 ("drm/panel: simple: Add Waveshare 13.3" panel support")
added definitions for one of those panels, describe the rest of them.
Note, since the panels are hidden behind the bridges which are not being
programmed by the kernel, I could not confirm the pixel format for the
panels.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260331-ws-lcd-v2-4-a1add63b6eb6@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Waveshare has a family of LVDS / DPI panels bundled with the DSI2DPI or
DSI2LVDS bridge. The bridge and the rest of the logic are covered by the
waveshare,dsi2dpi compatible. The bindings already include several
entries for the panels from this series (waveshare,13.3inch-panel,
waveshare,7.0inch-c-panel). Define compatible strings for the rest of
the panels from that series.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260331-ws-lcd-v2-3-a1add63b6eb6@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Implement amdxdna_show_fdinfo() to report per-client memory usage,
including below driver-specific memory stat:
- heap allocation
- internal BO allocation
- external BO allocation
Hook the implementation into the DRM fdinfo infrastructure via
drm_driver.show_fdinfo, while continuing to expose standard DRM
memory stat through drm_show_memory_stats().
This improves observability of per-process memory usage and aligns
with existing fdinfo reporting mechanisms used by other drivers.
Suggested-by: Ian Rogers <irogers@google.com>
Signed-off-by: Max Zhen <max.zhen@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260409152259.176883-1-lizhi.hou@amd.com
drm_bridge_get and drm_bridge_put() do nothing when they are passed a NULL
pointer, and they do so since their initial addition in commit 30d1b37d4c
("drm/bridge: add support for refcounting").
This allows simpler code in various places when using these
functions. However it's not documented, so it's not clear whether it is
part of the API "contract" or just a current implementation detail that
might change in the future.
There is no visible reason to remove this NULL check, so document it,
making it part of the contract, letting users count on it.
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://patch.msgid.link/20260324-drm-bridge-alloc-getput-document-null-check-v1-1-fb0877c49d7e@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
of_drm_find_bridge() is deprecated. Move to its replacement
of_drm_find_and_get_bridge() which gets a bridge reference, and ensure it
is put when done.
omapdss_device_init_output() can take one bridge pointer in out->bridge or
two pointers in out->bridge and out->next_bridge. Ensure each has a
corresponding drm_bridge_get() and add drm_bridge_put() calls in the
cleanup code.
Also slightly change the initial code assigning out->panel and out->bridge
to ensure and clarify that either out->panel or out->bridge is set in the
function prologue, not both. If both were set, the 'if (out->panel){...}'
code that follows would overwrite out->bridge without having put the
reference.
Finally, take a reference in case a panel_bridge is added using
drm_panel_bridge_add(). This ensures we always need to put a reference,
which came either from of_drm_find_and_get_bridge() or by the
drm_panel_bridge_add+drm_bridge_get() branch.
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260402-drm-bridge-alloc-getput-drm_of_find_bridge-4-v4-4-421781c8c061@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
of_drm_find_bridge() is deprecated. Move to its replacement
of_drm_find_and_get_bridge() which gets a bridge reference.
This driver has global variables for the DSI host and DSI device, and code
to allocate them on probe but no code to free them when on remove. So it
does not at all support removal, and not even multiple instances. For this
reason putting the reference would be pointless here.
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260402-drm-bridge-alloc-getput-drm_of_find_bridge-4-v4-2-421781c8c061@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
For both Rockchip and Exynos sides, the struct drm_connector* is
never used in callback &analogix_dp_plat_data.attach(). After
applying drm_bridge_connector helper, this parameter will no longer
be used at all.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20260409065301.446670-10-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
For Rockchip platforms, the YUV color formats are currently unsupported.
This compatibility check was previously implemented in
&analogix_dp_plat_data.get_modes().
Moving color format check to &drm_connector_helper_funcs.atomic_check()
would get rid of &analogix_dp_plat_data.get_modes() and be more
reasonable than before.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260409065301.446670-8-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
If there is neither a panel nor a bridge, the display timing can be
parsed from the display-timings node under the dp node.
In order to get rid of &analogix_dp_plat_data.get_modes() and make
the codes more consistent, apply DRM of-display-mode-bridge to parse
display timings.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260409065301.446670-6-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The &exynos_dp_device.connector is assigned in exynos_dp_bridge_attach()
but never used. It should make sense to remove it.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260409065301.446670-5-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
As suggested by Dmitry, the DRM legacy bridge driver can be pulled
out of imx/ subdir for multi-platform use. The driver is also renamed
to make it more generic and suitable for platforms other than i.MX.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260409065301.446670-3-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
In order to move the panel/bridge parsing and attachmenet to the
Analogix side, add component struct drm_bridge *next_bridge to
platform data struct analogix_dp_plat_data.
The movement makes sense because the panel/bridge should logically
be positioned behind the Analogix bridge in the display pipeline.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260409065301.446670-2-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Various substructures defined in panthor_sched.c have kernel-doc which
is silently ignored because it doesn't include the full path to the
member. Fix these issues so that the kernel-doc text is actually output
by including the name of the parent.
Fixes: de85488138 ("drm/panthor: Add the scheduler logical block")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patch.msgid.link/20260408091242.799074-1-steven.price@arm.com
By the time prepare_job() is called on a paired fragment job, the paired
geometry job might already be finished and its PM reference dropped.
Check the fragment job's PM reference instead which is a bit more likely
to be still set. This is a very minor optimization.
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
Reviewed-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Link: https://patch.msgid.link/20260330-job-submission-fixes-cleanup-v1-7-7de8c09cef8c@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Rename from done_fence to finished_fence, both because the function
returns a drm_sched_fence's finished fence, and to avoid confusion with
the job fence, which is called the same but has a different purpose.
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
Reviewed-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Link: https://patch.msgid.link/20260330-job-submission-fixes-cleanup-v1-5-7de8c09cef8c@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
