Since the referenced commit, changing the MTU on a running interface no
longer disconnects and reconnects the PHY; __stmmac_release() merely
stops phylink, which also suspends the PHY (BMCR power-down) when WoL
is not enabled. __stmmac_open() then performs the DMA software reset in
stmmac_hw_setup() before phylink_start() resumes the PHY again.
IEEE 802.3 22.2.4.1.5 allows a PHY to stop its receive clock while
powered down, and stmmac requires a running receive clock for the DMA
software reset to complete (the phylink config sets mac_requires_rxc).
On such setups, e.g. the RK3566-based Home Assistant Green with an
RTL8211F-VD PHY in RGMII mode, any runtime MTU change now times out and
leaves the interface dead:
rk_gmac-dwmac fe010000.ethernet end0: Failed to reset the dma
rk_gmac-dwmac fe010000.ethernet end0: stmmac_hw_setup: DMA engine initialization failed
rk_gmac-dwmac fe010000.ethernet end0: __stmmac_open: Hw setup failed
rk_gmac-dwmac fe010000.ethernet end0: failed reopening the interface after MTU change
In the field this is triggered by NetworkManager applying an MTU while
activating the connection, breaking networking entirely. The same
regression has also been reported on i.MX8MP and reproduced on SoCFPGA
based systems.
Resume the PHY in __stmmac_open() before the hardware setup, making it
the counterpart of the phylink_stop() in __stmmac_release(), like
stmmac_resume() already does for the same reason. phylink_start() also
resumes the PHY, but only after stmmac_hw_setup(), and it cannot be
moved before the hardware setup since it may bring the link up
immediately from a workqueue, racing with the initialization (see the
comment in stmmac_resume()). For the regular ndo_open path the PHY has
just been attached and is not suspended, in which case
phylink_prepare_resume() does nothing.
Fixes: db299a0c09 ("net: stmmac: move PHY handling out of __stmmac_open()/release()")
Link: https://github.com/home-assistant/operating-system/issues/4858
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260803095156.132827-1-stefan@agner.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The zero-copy path validates TX metadata while obtaining the descriptor
context, then reads it again later when preparing the hardware request.
User space can change the metadata between those operations and bypass the
original validation.
Validate the metadata in xsk_tx_metadata_request() and use the resulting
flags snapshot for every feature check. Read request fields once so all
zero-copy drivers process only values observed after successful
validation.
Fixes: ca4419f15a ("xsk: Add launch time hardware offload support to XDP Tx metadata")
Cc: Cen Zhang (Microsoft) <blbllhy@gmail.com>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260727161959.885642-7-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Completion handling needs to know whether a timestamp was requested when
the metadata was processed. Let xsk_tx_metadata_request() update the
caller's metadata pointer so that decision can be carried forward without
rereading user-controlled flags.
This only changes the interface; behavior remains unchanged.
Fixes: ca4419f15a ("xsk: Add launch time hardware offload support to XDP Tx metadata")
Cc: Cen Zhang (Microsoft) <blbllhy@gmail.com>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260727161959.885642-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For E2E delay mechanism, "received DELAY_REQ without timestamp" error
messages show up for dwmac v3.70+ and dwxgmac IPs.
This issue affects socfpga platforms, Agilex7 (dwmac 3.70) and
Agilex5 (dwxgmac). According to the databook, to enable timestamping
for all events, the SNAPTYPSEL bits in the MAC_Timestamp_Control
register must be set to 2'b01, and the TSEVNTENA bit must be cleared
to 0'b0.
Commit 3cb958027c ("net: stmmac: Fix E2E delay mechanism") already
addresses this problem for all dwmacs above version v4.10. However,
same holds true for v3.70 and above, as well as for dwxgmac. Updates
the check accordingly.
Fixes: 14f347334b ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Fixes: 3cb958027c ("net: stmmac: Fix E2E delay mechanism")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Link: https://patch.msgid.link/20260728060904.31993-1-muhammad.nazim.amirul.nazle.asmade@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
stmmac_mac_link_down() clears the MAC's transmit and receive enable bits.
stmmac_mac_link_up() is expected to set them again through
stmmac_mac_set(..., true), but it first switches on the negotiated speed
and returns early for a speed the switch does not list. The MAC is then
left gated off.
The speed selection is split into three switches, keyed on the interface.
The generic branch -- taken for everything that is neither USXGMII nor
XLGMII, so including PHY_INTERFACE_MODE_10GBASER -- lists only SPEED_2500,
SPEED_1000, SPEED_100 and SPEED_10.
MGBE on Tegra234 runs 10GBASE-R into an Aquantia AQR113C. That PHY does
rate matching, so phylink_link_up() replaces the media speed with the
MAC-side interface speed before calling into the MAC:
case RATE_MATCH_PAUSE:
speed = phylink_interface_max_speed(link_state.interface);
duplex = DUPLEX_FULL;
The driver is therefore called as
stmmac_mac_link_up(interface=10GBASER, speed=10000, duplex=1)
which falls through to "default: return;". The interface stops passing
traffic after the first link flap.
The failure is easy to misread. The link still comes up, because the PHY
is polled over MDIO and needs no MAC, so the interface reports carrier 1
at the media speed. The DMA is untouched, so its start bits stay set and
descriptors are still consumed. Only the MAC itself is gated off: the
receiver counts nothing (mmc_rx_framecount_gb stops advancing, RE is 0)
and nothing reaches the wire (TE is 0). The interface survives boot only
because stmmac_hw_setup(), called from ndo_open, enables the MAC
unconditionally -- so the problem appears only once the cable has been
unplugged and plugged back in, and "ip link set dev <ethX> down && ip
link set dev <ethX> up" appears to fix it.
The interface is not what the speed bits depend on: with the single
exception of 2.5G, which is selected through the XGMII block on USXGMII
and through the regular speed bits otherwise, each speed maps to one
field of struct mac_link. The per-interface switches are speed
validation, and phylink already validates the speed against
priv->hw->link.caps. So collapse the three switches into one keyed on the
speed alone, keeping the interface test only for the 2.5G case. This
covers 10G on 10GBASE-R, and equally 5G, and 1G/100/10 on USXGMII, all of
which hit "default: return;" today.
A core that does not support a speed leaves the corresponding mac_link
field at 0, and phylink will not offer it that speed in the first place.
For dwxgmac2 at 10G, link.xgmii.speed10000 is XGMAC_CONFIG_SS_10000,
which is 0 and is the correct speed selection for a 10GBASE-R MAC: ctrl
then equals old_ctrl, the register write is skipped, and execution
reaches stmmac_mac_set(..., true).
Log an error in the default case, since a speed with no entry here leaves
the MAC disabled and the symptom does not point at the cause.
Fixes: d8ca113724 ("net: stmmac: tegra: Add MGBE support")
Suggested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: vadik likholetov <vadikas@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260713074911.30090-1-vadikas@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When deleting an L3/L4 flower filter entry, the action field is not
reset. If a filter was previously configured with a drop action, that
action may persist and affect subsequent filter configurations
unintentionally.
Clear the action field when the filter entry is deleted.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-5-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The basic flow parser in tc_add_basic_flow() does not validate match
keys before proceeding. Unsupported offload configurations such as
partial protocol masks, non-IPv4 network proto, or non-TCP/UDP transport
proto are silently accepted instead of returning -EOPNOTSUPP.
Add validation to return -EOPNOTSUPP early for:
- No network or transport proto present in the key
- Partial protocol mask (only full mask supported)
- Network proto is not IPv4
- Transport proto is not TCP or UDP
Each rejection includes an extack message so the user knows which part
of the match is unsupported.
Also propagate -EOPNOTSUPP from tc_add_basic_flow() in tc_add_flow()
by returning it directly rather than using break. The break was silently
discarding the error for FLOW_CLS_REPLACE operations where entry->in_use
is already true, causing tc_add_flow() to return 0 (success) for
unsupported replace requests.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-4-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The XGMAC_L4_ADDR register holds both source and destination port
match values. The current implementation overwrites the entire register
when configuring either port, so setting one silently erases the other.
Fix this by reading the register first, then masking and updating only
the relevant field before writing back.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-3-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since commit 1b9707e6f1 ("net: stmmac: enable RPS and RBU
interrupts"), suspending causes an interrupt storm from the RPS
interrupt.
Fix this by adding a deinit_chan() op to stmmac_dma_ops, which
masks all default dma channel interrupts. This is called from
stmmac_stop_all_dma(), so interrupts don't trigger while suspending.
Fixes: 1b9707e6f1 ("net: stmmac: enable RPS and RBU interrupts")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Suggested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Luis Lang <luis.la@mail.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260720111534.163416-1-luis.la@mail.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
intel_mac_finish() is registered as the phylink mac_finish()
callback for the Elkhart Lake SGMII ports. phylink calls it at
the end of every major link reconfiguration, including the
initial one during probe.
The callback selects the PMC ModPHY LCPLL programming for the
requested MAC-side interface and then power-cycles the SerDes.
On Elkhart Lake that ModPHY is also used by the on-die AHCI
SATA PHY. Reapplying the programming during the initial
boot-time link-up disturbs the shared analog block while it is
still driving SATA, so the SATA link fails to train:
ata1: SATA link down (SStatus 1 SControl 300)
The disk carrying the root filesystem is never detected and the
system hangs at rootwait. Ethernet itself comes up normally,
which makes the failure look unrelated to the network driver.
Before mac_finish() runs, the legacy SerDes power-up path has
already programmed SERDES_GCR0 for the current interface. The
1G and 2.5G ModPHY tables selected by mac_finish() correspond
to the SerDes lane rate, so read that rate back from SERDES_GCR0
and skip the PMC reprogramming and SerDes power-cycle when it
already matches the selected interface.
This keeps the disruptive reprogramming out of the boot path
when the SerDes is configured correctly, while preserving the
previous behavior when a real SGMII/1000BASE-X to 2500BASE-X
rate change is needed. If the register read fails, reconfigure
as before.
Fixes: a42f6b3f1c ("net: stmmac: configure SerDes according to the interface mode")
Cc: stable@vger.kernel.org
Signed-off-by: Markus Breitenberger <bre@keba.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260713171619.192452-1-bre@breiti.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
The current irq definition of the wake irq and the lpi irq
is wrong, replace them with the right number and name.
Fixes: 30f0ba420e ("net: stmmac: Add glue layer for Spacemit K3 SoC")
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260623074637.503864-3-inochiama@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current MII interface register definition from the vendor is wrong,
use the right number for the macro. Also, correct the interface mask
in spacemit_set_phy_intf_sel() so it can update the register with the
right number
Fixes: 30f0ba420e ("net: stmmac: Add glue layer for Spacemit K3 SoC")
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260623074637.503864-2-inochiama@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Core & protocols
----------------
- Work on removing rtnl_lock protection throughout the stack continues.
In this chapter:
- don't use rtnl_lock for IPv6 multicast routing configuration
- don't take rtnl_lock in ethtool for modern drivers
- prepare Qdisc dump callbacks for rtnl_lock removal
- Support dumping just ifindex + name of all interfaces, under RCU.
It's a common operation for Netlink CLI tools (when translating
names to ifindexes) and previously required full rtnl_lock.
- Support dumping qdiscs and page pools for a specific netdev. Even tho
user space wants a dump of all netdevs, most of the time, the OOO
programming model results in repeating the dump for each netdev.
Which, in absence of a cache, leads to a O(n^2) behavior.
- Flush nexthops once on multi-nexthop removal (e.g. when device goes
down), another O(n^2) -> O(n) improvement.
- Rehash locally generated traffic to a different nexthop on retransmit
timeout.
- Honor oif when choosing nexthop for locally generated IPv6 traffic.
- Convert TCP Auth Option to crypto library, and drop non-RFC algos.
- Increase subflow limits in MPTCP to 64 and endpoint limit to 256.
- Support MPTCP signaling of IPv6 address + port (ADD_ADDR). We need
to selectively skip reporting of the standard TCP Timestamp option,
because they won't fit into the header space together (12 + 30 > 40).
- Support using bridge neighbor suppression, Duplicate Address
Detection, Gratuitous ARP and unsolicited NA forwarding - in EVPN
deployments, e.g. VXLAN fabrics (IPv4 and IPv6).
- Improve link state reporting for upper netdevs (e.g. macvlan) over
tunnel devices (again, mostly for EVPN deployments).
- Support binding GENEVE tunnels to a local address.
- Speed up UDP tunnel destruction (remove one synchronize_rcu()).
- Support exponential field encoding in multicast (IGMPv3 and MLDv2).
- Support attaching PSP crypto offload to containers (veth, netkit).
- Add a new IPSec Netlink message XFRM_MSG_MIGRATE_STATE that allows
migrating individual IPsec SAs independently of their policies.
The existing XFRM_MSG_MIGRATE is tightly coupled to policy+SA
migration, lacks SPI for unique SA identification, and cannot express
reqid changes or migrate Transport mode selectors. The new interface
identifies the SA via SPI and mark, supports reqid changes, address
family changes, encap removal, and uses an atomic create+install
flow under x->lock to prevent SN/IV reuse during AEAD SA migration.
- Implement GRO/GSO support for PPPoE.
- Convert sockopt callbacks in a number of protocols to iov_iter.
Cross-tree stuff
----------------
- Remove support for Crypto TFM cloning (unblocked after the TCP Auth
Option rework). This feature regressed performance for all crypto API
users, since it changed crypto transformation objects into reference-
-counted objects.
- Add FCrypt-PCBC implementation to rxrpc and remove it from the global
crypto API as obsolete and insecure.
Wireless
--------
- Major rework of station bandwidth handling, fixing issues with lower
capability than AP.
- Cleanups for EMLSR spec issues (drafts differed).
- More Neighbor Awareness Networking (Wi-Fi Aware) work (multicast,
schedule improvements, multi-station etc.)
- Some Ultra High Reliability (UHR) / IEEE 802.11bn (D1.4) work
(e.g. non-primary channel access, UHR DBE support).
- Fine Timing Measurement ranging (i.e. distance measurement) APIs.
Netfilter
---------
- Use per-rule hash initval in nf_conncount. This avoids unnecessary
lock contention with short keys (e.g. conntrack zones) in different
namespaces.
- Various safety improvements, both in packet parsing and object
lifetimes. Notably add refcounts to conntrack timeout policy.
Deletions
---------
- Remove TLS + sockmap integration. TLS wants to pin user pages
to avoid a copy, and sockmap wants to write to the input stream.
More work on this integration is clearly needed, and we can't find
any users (original author admitted that they never deployed it).
- Remove support for TLS offload with TCP Offload Engine (the far
more common opportunistic offload is retained). The locking looks
unfixable (driver sleeps under TCP spin locks) and people from
the vendor that added this are AWOL.
- Remove more ATM code, trying to leave behind only what PPPoATM needs,
AAL5 and br2684 with permanent circuits.
- Remove AppleTalk. Let it join hamradio in our out of tree protocol
graveyard, I mean, repository.
- Disable 32-bit x_tables compatibility (32bit binaries on 64bit kernel)
interface in user namespaces. To be deleted completely, soon.
- Remove 5/10 MHz support from cfg80211/mac80211.
Drivers
-------
- Software:
- Support DEVMEM/DMABUF Tx over NETMEM_TX_NO_DMA devices (netkit).
- bonding: add knob to strictly follow 802.3ad for link state.
- New drivers:
- Alibaba Elastic Ethernet Adaptor (cloud vNIC).
- NXP NETC switch within i.MX94.
- DPLL:
- Add operational state to pins (implement in zl3073x).
- Add generic DPLL type, for daisy-chaining DPLLs (implement in ice).
- Ethernet high-speed NICs:
- Huawei (hinic3):
- enhance tc flow offload support with queue selection, tunnels
- nVidia/Mellanox:
- avoid over-copying payload to the skb's linear part (up to 60%
win for LRO on slow CPUs like ARM64 V2)
- expose more per-queue stats over the standard API
- support additional, unprivileged PFs in the DPU configuration
- support Socket Direct (multi-PF) with switchdev offloads
- add a pool / frag allocator for DMA mapped buffers for control
objects, save memory on systems with 64kB page size
- take advantage of the ability to dynamically change RSS table
size, even when table is configured by the user
- increase the max RSS table size for even traffic distribution
- Ethernet NICs:
- Marvell/Aquantia:
- AQC113 PTP support
- Realtek USB (r8152):
- support 10Gbit Link Speeds and Energy-Efficient Ethernet (EEE)
- support firmware loaded (for RTL8157/RTL8159)
- support for the RTL8159
- Intel (ixgbe):
- support Energy-Efficient Ethernet (EEE) on E610 devices
- Ethernet switches:
- Airoha:
- support multiple netdevs on a single GDM block / port
- Marvell (mv88e6xxx):
- support SERDES of mv88e6321
- Microchip (ksz8/9):
- rework the driver callbacks to remove one indirection layer
- Motorcomm (yt921x):
- support port rate policing
- support TBF qdisc offload
- support ACL/flower offload
- nVidia/Mellanox:
- expose per-PG rx_discards
- Realtek:
- rtl8365mb: bridge offloading and VLAN support
- Ethernet PHYs:
- Airoha:
- support Airoha AN8801R Gigabit PHYs.
- Micrel:
- implement 3 low-loss cable tunables
- Realtek:
- support MDI swapping for RTL8226-CG
- support MDIO for RTL931x
- Qualcomm:
- at803x: Rx and Tx clock management for IPQ5018 PHY
- Motorcomm:
- support YT8522 100M RMII PHY
- set drive strength in YT8531s RGMII
- TI:
- dp83822: add optional external PHY clock
- Bluetooth:
- hci_sync: add support for HCI_LE_Set_Host_Feature [v2]
- SMP: use AES-CMAC library API
- Intel:
- support Product level reset
- support smart trigger dump
- Mediatek:
- add event filter to filter specific event
- Realtek:
- fix RTL8761B/BU broken LE extended scan
- WiFi:
- Broadcom (b43):
- new support for a 11n device
- MediaTek (mt76):
- support mt7927
- mt792x: broken usb transport detection
- mt7921: regulatory improvements
- Qualcomm (ath9k):
- GPIO interface improvements
- Qualcomm (ath12k):
- WDS support
- replace dynamic memory allocation in WMI Rx path
- thermal throttling/cooling device support
- 6 GHz incumbent interference detection
- channel 177 in 5 GHz
- Realtek (rt89):
- RTL8922AU support
- USB 3 mode switch for performance
- better monitor radiotap support
- RTL8922DE preparations
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oNfE
-----END PGP SIGNATURE-----
Merge tag 'net-next-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Work on removing rtnl_lock protection throughout the stack
continues. In this chapter:
- don't use rtnl_lock for IPv6 multicast routing configuration
- don't take rtnl_lock in ethtool for modern drivers
- prepare Qdisc dump callbacks for rtnl_lock removal
- Support dumping just ifindex + name of all interfaces, under RCU.
It's a common operation for Netlink CLI tools (when translating
names to ifindexes) and previously required full rtnl_lock.
- Support dumping qdiscs and page pools for a specific netdev. Even
tho user space wants a dump of all netdevs, most of the time, the
OOO programming model results in repeating the dump for each
netdev. Which, in absence of a cache, leads to a O(n^2) behavior.
- Flush nexthops once on multi-nexthop removal (e.g. when device goes
down), another O(n^2) -> O(n) improvement.
- Rehash locally generated traffic to a different nexthop on
retransmit timeout.
- Honor oif when choosing nexthop for locally generated IPv6 traffic.
- Convert TCP Auth Option to crypto library, and drop non-RFC algos.
- Increase subflow limits in MPTCP to 64 and endpoint limit to 256.
- Support MPTCP signaling of IPv6 address + port (ADD_ADDR). We need
to selectively skip reporting of the standard TCP Timestamp option,
because they won't fit into the header space together (12 + 30 >
40).
- Support using bridge neighbor suppression, Duplicate Address
Detection, Gratuitous ARP and unsolicited NA forwarding - in EVPN
deployments, e.g. VXLAN fabrics (IPv4 and IPv6).
- Improve link state reporting for upper netdevs (e.g. macvlan) over
tunnel devices (again, mostly for EVPN deployments).
- Support binding GENEVE tunnels to a local address.
- Speed up UDP tunnel destruction (remove one synchronize_rcu()).
- Support exponential field encoding in multicast (IGMPv3 and MLDv2).
- Support attaching PSP crypto offload to containers (veth, netkit).
- Add a new IPSec Netlink message XFRM_MSG_MIGRATE_STATE that allows
migrating individual IPsec SAs independently of their policies.
The existing XFRM_MSG_MIGRATE is tightly coupled to policy+SA
migration, lacks SPI for unique SA identification, and cannot
express reqid changes or migrate Transport mode selectors.
The new interface identifies the SA via SPI and mark, supports
reqid changes, address family changes, encap removal, and uses an
atomic create+install flow under x->lock to prevent SN/IV reuse
during AEAD SA migration.
- Implement GRO/GSO support for PPPoE.
- Convert sockopt callbacks in a number of protocols to iov_iter.
Cross-tree stuff:
- Remove support for Crypto TFM cloning (unblocked after the TCP Auth
Option rework). This feature regressed performance for all crypto
API users, since it changed crypto transformation objects into
reference-counted objects.
- Add FCrypt-PCBC implementation to rxrpc and remove it from the
global crypto API as obsolete and insecure.
Wireless:
- Major rework of station bandwidth handling, fixing issues with
lower capability than AP.
- Cleanups for EMLSR spec issues (drafts differed).
- More Neighbor Awareness Networking (Wi-Fi Aware) work (multicast,
schedule improvements, multi-station etc.)
- Some Ultra High Reliability (UHR) / IEEE 802.11bn (D1.4) work
(e.g. non-primary channel access, UHR DBE support).
- Fine Timing Measurement ranging (i.e. distance measurement) APIs.
Netfilter:
- Use per-rule hash initval in nf_conncount. This avoids unnecessary
lock contention with short keys (e.g. conntrack zones) in different
namespaces.
- Various safety improvements, both in packet parsing and object
lifetimes. Notably add refcounts to conntrack timeout policy.
Deletions:
- Remove TLS + sockmap integration. TLS wants to pin user pages to
avoid a copy, and sockmap wants to write to the input stream. More
work on this integration is clearly needed, and we can't find any
users (original author admitted that they never deployed it).
- Remove support for TLS offload with TCP Offload Engine (the far
more common opportunistic offload is retained). The locking looks
unfixable (driver sleeps under TCP spin locks) and people from the
vendor that added this are AWOL.
- Remove more ATM code, trying to leave behind only what PPPoATM
needs, AAL5 and br2684 with permanent circuits.
- Remove AppleTalk. Let it join hamradio in our out of tree protocol
graveyard, I mean, repository.
- Disable 32-bit x_tables compatibility (32bit binaries on 64bit
kernel) interface in user namespaces. To be deleted completely,
soon.
- Remove 5/10 MHz support from cfg80211/mac80211.
Drivers:
- Software:
- Support DEVMEM/DMABUF Tx over NETMEM_TX_NO_DMA devices (netkit)
- bonding: add knob to strictly follow 802.3ad for link state
- New drivers:
- Alibaba Elastic Ethernet Adaptor (cloud vNIC).
- NXP NETC switch within i.MX94.
- DPLL:
- Add operational state to pins (implement in zl3073x).
- Add generic DPLL type, for daisy-chaining DPLLs (implement in ice).
- Ethernet high-speed NICs:
- Huawei (hinic3):
- enhance tc flow offload support with queue selection,
tunnels
- nVidia/Mellanox:
- avoid over-copying payload to the skb's linear part (up to
60% win for LRO on slow CPUs like ARM64 V2)
- expose more per-queue stats over the standard API
- support additional, unprivileged PFs in the DPU
configuration
- support Socket Direct (multi-PF) with switchdev offloads
- add a pool / frag allocator for DMA mapped buffers for
control objects, save memory on systems with 64kB page size
- take advantage of the ability to dynamically change RSS
table size, even when table is configured by the user
- increase the max RSS table size for even traffic
distribution
- Ethernet NICs:
- Marvell/Aquantia:
- AQC113 PTP support
- Realtek USB (r8152):
- support 10Gbit Link Speeds and Energy-Efficient Ethernet
(EEE)
- support firmware loaded (for RTL8157/RTL8159)
- support for the RTL8159
- Intel (ixgbe):
- support Energy-Efficient Ethernet (EEE) on E610 devices
- Ethernet switches:
- Airoha:
- support multiple netdevs on a single GDM block / port
- Marvell (mv88e6xxx):
- support SERDES of mv88e6321
- Microchip (ksz8/9):
- rework the driver callbacks to remove one indirection layer
- Motorcomm (yt921x):
- support port rate policing
- support TBF qdisc offload
- support ACL/flower offload
- nVidia/Mellanox:
- expose per-PG rx_discards
- Realtek:
- rtl8365mb: bridge offloading and VLAN support
- Ethernet PHYs:
- Airoha:
- support Airoha AN8801R Gigabit PHYs.
- Micrel:
- implement 3 low-loss cable tunables
- Realtek:
- support MDI swapping for RTL8226-CG
- support MDIO for RTL931x
- Qualcomm:
- at803x: Rx and Tx clock management for IPQ5018 PHY
- Motorcomm:
- support YT8522 100M RMII PHY
- set drive strength in YT8531s RGMII
- TI:
- dp83822: add optional external PHY clock
- Bluetooth:
- hci_sync: add support for HCI_LE_Set_Host_Feature [v2]
- SMP: use AES-CMAC library API
- Intel:
- support Product level reset
- support smart trigger dump
- Mediatek:
- add event filter to filter specific event
- Realtek:
- fix RTL8761B/BU broken LE extended scan
- WiFi:
- Broadcom (b43):
- new support for a 11n device
- MediaTek (mt76):
- support mt7927
- mt792x: broken usb transport detection
- mt7921: regulatory improvements
- Qualcomm (ath9k):
- GPIO interface improvements
- Qualcomm (ath12k):
- WDS support
- replace dynamic memory allocation in WMI Rx path
- thermal throttling/cooling device support
- 6 GHz incumbent interference detection
- channel 177 in 5 GHz
- Realtek (rt89):
- RTL8922AU support
- USB 3 mode switch for performance
- better monitor radiotap support
- RTL8922DE preparations"
* tag 'net-next-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1778 commits)
ipv4: fib_rule: Move fib4_rules_exit() to ->exit().
net: serialize netif_running() check in enqueue_to_backlog()
net: skmsg: preserve sg.copy across SG transforms
appletalk: move the protocol out of tree
appletalk: stop storing per-interface state in struct net_device
selftests/bpf: test that TLS crypto is rejected on a sockmap socket
selftests/bpf: drop the unused kTLS program from test_sockmap
selftests/bpf: remove sockmap + ktls tests
tls: remove dead sockmap (psock) handling from the SW path
tls: reject the combination of TLS and sockmap
atm: remove orphaned uAPI for deleted drivers, protocols and SVCs
atm: remove unused ATM PHY operations
atm: remove the unused pre_send and send_bh device operations
atm: remove the unused change_qos device operation
atm: remove SVC socket support and the signaling daemon interface
atm: remove the local ATM (NSAP) address registry
atm: remove dead SONET PHY ioctls
atm: remove the unused send_oam / push_oam callbacks
atm: remove AAL3/4 transport support
net: dsa: sja1105: fix lastused timestamp in flower stats
...
- CPUID API updates (Ahmed S. Darwish):
- Introduce a centralized CPUID parser
- Introduce a centralized CPUID data model
- Introduce <asm/cpuid/leaf_types.h>
- Rename cpuid_leaf()/cpuid_subleaf() APIs
- treewide: Explicitly include the x86 CPUID headers
- Update to x86-cpuid-db v3.1 (Maciej Wieczor-Retman)
- Continued removal of pre-i586 support and related
simplifications (Ingo Molnar)
- Add Intel CPU model number for rugged Panther Lake
(Tony Luck)
- Misc fixes, updates and cleanups by Arnd Bergmann, Chao Gao,
Lukas Bulwahn, Sohil Mehta, Maciej Wieczor-Retman.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=tpai
-----END PGP SIGNATURE-----
Merge tag 'x86-cpu-2026-06-14' of gitolite.kernel.org:pub/scm/linux/kernel/git/tip/tip
Pull x86 cpuid updates from Ingo Molnar:
- CPUID API updates (Ahmed S. Darwish):
- Introduce a centralized CPUID parser
- Introduce a centralized CPUID data model
- Introduce <asm/cpuid/leaf_types.h>
- Rename cpuid_leaf()/cpuid_subleaf() APIs
- treewide: Explicitly include the x86 CPUID headers
- Update to x86-cpuid-db v3.1 (Maciej Wieczor-Retman)
- Continued removal of pre-i586 support and related simplifications
(Ingo Molnar)
- Add Intel CPU model number for rugged Panther Lake (Tony Luck)
- Misc fixes, updates and cleanups by Arnd Bergmann, Chao Gao, Lukas
Bulwahn, Sohil Mehta, Maciej Wieczor-Retman.
* tag 'x86-cpu-2026-06-14' of gitolite.kernel.org:pub/scm/linux/kernel/git/tip/tip: (25 commits)
x86/cpu: Make CONFIG_X86_CX8 unconditional
x86/cpu: Remove unused !CONFIG_X86_TSC code
x86/cpuid: Update bitfields to x86-cpuid-db v3.1
tools/x86/kcpuid: Update bitfields to x86-cpuid-db v3.1
x86/cpu: Make CONFIG_X86_TSC unconditional
MAINTAINERS: Drop obsolete FPU EMULATOR section
x86/cpu: Fix a F00F bug warning and clean up surrounding code
x86/cpu: Add Intel CPU model number for rugged Panther Lake
x86/cpuid: Introduce a centralized CPUID parser
x86/cpu: Introduce a centralized CPUID data model
x86/cpuid: Introduce <asm/cpuid/leaf_types.h>
x86/cpuid: Rename cpuid_leaf()/cpuid_subleaf() APIs
x86/cpu: Do not include the CPUID API header in asm/processor.h
Documentation: core-api/cpu_hotplug: Remove stale cpu0_hotplug docs
x86/cpu, cpufreq: Remove AMD ELAN support
x86/fpu: Remove the math-emu/ FPU emulation library
x86/fpu: Remove the 'no387' boot option
x86/fpu: Remove MATH_EMULATION and related glue code
treewide: Explicitly include the x86 CPUID headers
x86/cpu: Remove the CONFIG_X86_INVD_BUG quirk
...
When "snps,rx-queues-to-use" or "tx-queues-to-use" config in DTS is provided
current code will apply U8_MAX value for queues_to_use if there is input of
higher value. But actual maximum number of supported queues is set via
macro MTL_MAX_RX_QUEUES and MTL_MAX_TX_QUEUES, which currently have value of 8.
This value of U8_MAX will be capped to value provided by core in DMA
capabilities (dma_conf), but it does so only if core provides it.
This is true for XGMAC (dwxgmac2) and some GMAC (dwmac4),
but not for (dwmac1000). This capping is at later stage in stmmac_hw_init(),
and during stmmac_mtl_setup() we might parse fields outside allocated memory
if queues_to_use is over defines MTL_MAX_ values,
for example following rx_queues_cfg is array of size of MTL_MAX_RX_QUEUES.
Fix this by capping value to MTL_MAX during config parsing.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260611113358.3379518-3-j.raczynski@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While opening stmmac driver, there is enabling of TBS (Time-Based Scheduling)
option in dma config. Currently this is executed for all possible TX queues via
MTL_MAX_TX_QUEUES macro, but actual number of queues used might differ.
While setting this is generally harmless, since memory for MTL_MAX_TX_QUEUES
is allocated, it is incorrect, because it prepares config for unused queues.
Change this to apply tbs config only to tx_queues_to_use.
Co-developed-by: Chang-Sub Lee <cs0617.lee@samsung.com>
Signed-off-by: Chang-Sub Lee <cs0617.lee@samsung.com>
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260611113358.3379518-2-j.raczynski@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enabling the RX Buffer Unavailable (RBUE) interrupt is counterproductive
and can trigger a MAC interrupt storm under heavy RX pressure. When the
DMA runs out of RX descriptors it fires RBUE continuously until software
refills the ring.
However, RBUE is redundant: the normal RX completion interrupt (RIE)
already triggers NAPI, which processes completed descriptors and refills
the ring, causing the DMA to resume. The RBUE handler itself only sets
handle_rx - the same outcome as RIE.
On Agilex5 under heavy RX pressure, the MAC interrupt (which includes
RBUE) was observed firing 1,821,811,555 times against only 2,618,627
actual RX completions - a ~695x ratio - confirming the severity of the
storm.
RBUE does not provide OOM recovery. If page_pool is exhausted,
stmmac_rx_refill() cannot advance the DMA tail pointer, the DMA stays
suspended, and RBUE fires again on the next NAPI completion - a storm
with no forward progress. This patch trades that storm for a clean
stall with the same RX outcome. Proper OOM recovery is a pre-existing
gap outside the scope of this fix.
Note: as a consequence of disabling RBUE, the rx_buf_unav_irq ethtool
counter will always read 0 on XGMAC2 devices. This behaviour is already
inconsistent across DWMAC core versions.
Remove RBUE from XGMAC_DMA_INT_DEFAULT_EN and XGMAC_DMA_INT_DEFAULT_RX
to prevent the interrupt storm while keeping normal RX handling intact.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260609121703.9736-1-muhammad.nazim.amirul.nazle.asmade@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Read the L3FM and L4FM bits from the RX descriptor status word (RDES2)
and increment the corresponding ethtool statistics counters. This allows
users to observe L3/L4 filter hit rates via ethtool -S.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260604083037.24407-1-muhammad.nazim.amirul.nazle.asmade@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bit 16 of the MAC HW Feature1 register reports the DCB (Data Centre
Bridging) feature. Read it so that dma_cap.dcben and the debugfs
report it accurately. Right now it is always reported as being disabled.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260603173644.24371-1-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling hrtimer_start() on an already-active txtimer is unnecessary
and expensive. Skip the restart if the timer is already active by
adding an hrtimer_active() check before hrtimer_start().
Previously, each packet reset the timer to tx_coal_timer in the future,
acting as a sliding window that delayed NAPI under burst traffic. With
this change, an already-active timer is left to fire sooner, scheduling
NAPI within tx_coal_timer of the first packet and freeing TX descriptors
earlier.
There is no race concern: hrtimer_start() is internally serialized and
safe to call on an active timer. In the event of a race between
hrtimer_active() and hrtimer_start(), the worst case is calling
hrtimer_start() on an already-active timer, which is identical to the
pre-patch behaviour.
Performance on Cyclone V with dwmac-socfpga (iperf3 -u -b 0 -l 64):
Before: ~45200 pps
After: ~52300 pps (~15% improvement)
Additionally, ~10% improvement in UDP throughput observed on Agilex5,
with hrtimer CPU usage reduced from ~8% to ~0.6%.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260529064659.32287-1-muhammad.nazim.amirul.nazle.asmade@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add jhb100 compatible and SGMII support. jhb100 soc contains
2 SGMII interfaces and integrated with serdes PHY. SGMII with
split TX/RX MAC clock and need to set 2.5M/25M/125M TX/RX clock
rate in 10M/100M/1000M speed mode.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Sai Krishna <saikrishnag@marvell.com>
Link: https://patch.msgid.link/20260527084108.121416-4-minda.chen@starfivetech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MMC_XGMAC_RX_CRC_ERR is clear-on-read, and just a single read would
update the mmc_rx_crc_error counter.
The duplicate read appears to have been unintentionally introduced in
the intial MMC counter implementation [1]. The databook does not mention
MMC_XGMAC_RX_CRC_ERR needing the additional read.
[1] commit b6cdf09f51 ("net: stmmac: xgmac: Implement MMC counters")
Signed-off-by: Abid Ali <dev.taqnialabs@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260521-xgmac-mmc_rx_crc-cleanup-v2-1-7d9de09f5898@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Validate rx-internal-delay-ps and tx-internal-delay-ps against the
hardware capabilities of the EIC7700 MAC.
The programmable RGMII delay supports 20 ps steps and a maximum value of
2540 ps. The driver previously accepted arbitrary values and silently
truncated unsupported settings when converting them to hardware units.
As a result, invalid device tree values could lead to unexpected delay
programming and incorrect RGMII timing.
Reject delay values that are not multiples of 20 ps or exceed the
supported hardware range.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022214.507-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The EIC7700 MAC implements programmable RGMII delay adjustment with a
granularity of 20 ps per hardware step.
The driver previously converted rx-internal-delay-ps and
tx-internal-delay-ps values using a 100 ps step size, resulting in
incorrect delay programming.
Update the conversion to use the correct 20 ps granularity so the
programmed delay matches the values described in the device tree.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022156.484-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Clear the TXD and RXD delay control registers during EIC7700 DWMAC
initialization.
These registers may retain values programmed by the bootloader. If left
unchanged, residual delays can alter the effective RGMII timing seen by
the MAC and override the configuration described by the device tree.
This may violate the expected RGMII timing model and can cause link
instability or prevent the Ethernet controller from operating correctly.
Explicitly clearing these registers ensures that the MAC delay settings
are determined solely by the kernel configuration.
The corresponding register offsets are optional, and the registers are
only cleared when the offsets are provided in the device tree.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022137.464-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix the initialization ordering of the HSP CSR configuration in the
EIC7700 DWMAC glue driver.
The HSP CSR registers control MAC-side RGMII delay behavior and must
only be accessed after the corresponding clocks are enabled. The
previous implementation could trigger register access before clock
enablement, leading to undefined behavior depending on boot state.
Move the HSP CSR configuration into the post-clock-enable initialization
path to ensure all register accesses occur under valid clock domains.
This change ensures deterministic initialization and prevents
clock-dependent register access failures during probe or resume.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022055.444-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
priv->dev was never initialized after devm_kzalloc() allocates the
private data structure. When nvt_set_phy_intf_sel() is later invoked
via the phylink interface_select callback, it calls
nvt_gmac_get_delay(priv->dev, ...) which dereferences the NULL pointer.
Fix this by assigning priv->dev = dev immediately after allocation.
Fixes: 4d7c557f58 ("net: stmmac: dwmac-nuvoton: Add dwmac glue for Nuvoton MA35 family")
Signed-off-by: Joey Lu <a0987203069@gmail.com>
Link: https://patch.msgid.link/20260506084614.192894-2-a0987203069@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Modify all CPUID call sites which implicitly include any of the CPUID
headers to explicitly include them instead.
For KVM's reverse_cpuid.h, just include <asm/cpuid/types.h> since it
references the CPUID_EAX..EDX symbols without using the CPUID APIs.
Note, this allows removing the inclusion of <asm/cpuid/api.h> from within
<asm/processor.h> next. That allows the CPUID API headers to include
<asm/processor.h> without introducing a circular dependency.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20260327021645.555257-1-darwi@linutronix.de
The CPU receives frames from the MAC through conventional DMA: the CPU
allocates buffers for the MAC, then the MAC fills them and returns
ownership to the CPU. For each hardware RX queue, the CPU and MAC
coordinate through a shared ring array of DMA descriptors: one
descriptor per DMA buffer. Each descriptor includes the buffer's
physical address and a status flag ("OWN") indicating which side owns
the buffer: OWN=0 for CPU, OWN=1 for MAC. The CPU is only allowed to set
the flag and the MAC is only allowed to clear it, and both must move
through the ring in sequence: thus the ring is used for both
"submissions" and "completions."
In the stmmac driver, stmmac_rx() bookmarks its position in the ring
with the `cur_rx` index. The main receive loop in that function checks
for rx_descs[cur_rx].own=0, gives the corresponding buffer to the
network stack (NULLing the pointer), and increments `cur_rx` modulo the
ring size. After the loop exits, stmmac_rx_refill(), which bookmarks its
position with `dirty_rx`, allocates fresh buffers and rearms the
descriptors (setting OWN=1). If it fails any allocation, it simply stops
early (leaving OWN=0) and will retry where it left off when next called.
This means descriptors have a three-stage lifecycle (terms my own):
- `empty` (OWN=1, buffer valid)
- `full` (OWN=0, buffer valid and populated)
- `dirty` (OWN=0, buffer NULL)
But because stmmac_rx() only checks OWN, it confuses `full`/`dirty`. In
the past (see 'Fixes:'), there was a bug where the loop could cycle
`cur_rx` all the way back to the first descriptor it dirtied, resulting
in a NULL dereference when mistaken for `full`. The aforementioned
commit resolved that *specific* failure by capping the loop's iteration
limit at `dma_rx_size - 1`, but this is only a partial fix: if the
previous stmmac_rx_refill() didn't complete, then there are leftover
`dirty` descriptors that the loop might encounter without needing to
cycle fully around. The current code therefore panics (see 'Closes:')
when stmmac_rx_refill() is memory-starved long enough for `cur_rx` to
catch up to `dirty_rx`.
Fix this by explicitly checking, before advancing `cur_rx`, if the next
entry is dirty; exit the loop if so. This prevents processing of the
final, used descriptor until stmmac_rx_refill() succeeds, but
fully prevents the `cur_rx == dirty_rx` ambiguity as the previous bugfix
intended: so remove the clamp as well. Since stmmac_rx_zc() is a
copy-paste-and-tweak of stmmac_rx() and the code structure is identical,
any fix to stmmac_rx() will also need a corresponding fix for
stmmac_rx_zc(). Therefore, apply the same check there.
In stmmac_rx() (not stmmac_rx_zc()), a related bug remains: after the
MAC sets OWN=0 on the final descriptor, it will be unable to send any
further DMA-complete IRQs until it's given more `empty` descriptors.
Currently, the driver simply *hopes* that the next stmmac_rx_refill()
succeeds, risking an indefinite stall of the receive process if not. But
this is not a regression, so it can be addressed in a future change.
Fixes: b6cb454185 ("net: stmmac: avoid rx queue overrun")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221010
Cc: stable@vger.kernel.org
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Link: https://patch.msgid.link/20260422044503.5349-1-CFSworks@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
get_interfaces() will update both the plat->phy_interfaces and
mdio_bus_data->default_an_inband based on reading a SERDES register. As
get_interfaces() will be called after default_an_inband had already been
read, dwmac-intel regressed as a result with incorrect default_an_inband
value in phylink_config.
Therefore, we moved the priv->plat->get_interfaces() to be executed first
before assigning priv->plat->default_an_inband to config->default_an_inband
to ensure default_an_inband is in correct value.
Fixes: d3836052fe ("net: stmmac: intel: convert speed_mode_2500() to get_interfaces()")
Signed-off-by: KhaiWenTan <khai.wen.tan@linux.intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260416102609.7953-1-khai.wen.tan@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable receive process stopped and receive buffer unavailable
interrupts, so that the statistic counters can be updated.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1wBBaR-0000000GZHR-1dbM@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch fixes an issue where reading the MAC address from the eFUSE
fails due to a race condition.
The root cause was identified by comparing the driver's behavior with a
custom U-Boot port. In U-Boot, the MAC address was read successfully
every time because the driver was loaded later in the boot process, giving
the hardware ample time to initialize. In Linux, reading the eFUSE
immediately returns all zeros, resulting in a fallback to a random MAC address.
Hardware cold-boot testing revealed that the eFUSE controller requires a
short settling time to load its internal data. Adding a 2000-5000us
delay after the reset ensures the hardware is fully ready, allowing the
native MAC address to be read consistently.
Fixes: 02ff155ea2 ("net: stmmac: Add glue driver for Motorcomm YT6801 ethernet controller")
Reported-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Closes: https://lore.kernel.org/24cfefff-1233-4745-8c47-812b502d5d19@tuxedocomputers.com
Signed-off-by: Johan Alvarado <contact@c127.dev>
Reviewed-by: Yao Zi <me@ziyao.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/fc5992a4-9532-49c3-8ec1-c2f8c5b84ca1@smtp-relay.sendinblue.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 030ce919e1 ("net: stmmac: make sure that ptp_rate is not
0 before configuring timestamping") was added the following error is
observed on Tegra234:
ERR KERN tegra-mgbe 6800000.ethernet eth0: Invalid PTP clock rate
WARNING KERN tegra-mgbe 6800000.ethernet eth0: PTP init failed
It turns out that the Tegra234 device-tree binding defines the PTP ref
clock name as 'ptp-ref' and not 'ptp_ref' and the above commit now
exposes this and that the PTP clock is not configured correctly.
In order to update device-tree to use the correct 'ptp_ref' name, update
the Tegra MGBE driver to use 'ptp_ref' by default and fallback to using
'ptp-ref' if this clock name is present.
Fixes: d8ca113724 ("net: stmmac: tegra: Add MGBE support")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260401102941.17466-2-jonathanh@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The clocks for qcom-ethqos return a rate of zero as firmware manages
their rate. According to hardware documentation, the clock which is
fed to the slave AHB interface can range between 50 to 100MHz for
non-RGMII and 30 to 75MHz for boards with a RGMII interfaces.
Currently, stmmac uses an undefined divisor value. Instead, use
STMMAC_CSR_60_100M which will mean we meet IEEE 802.3 specification
since this will generate:
714kHz @ 30MHz
1.19MHz @ 50MHz
1.79MHz @ 75MHz
2.42MHz @ 100MHz
This gives MDC rates within the IEEE 802.3 specification, although the
30MHz case is particularly slow.
Selecting the next lowest divisor, STMMAC_CSR_35_60M, which is /26
will give:
1.15MHz @ 30MHz
1.92MHz @ 50MHz
2.88MHz @ 75MHz (exceeding 802.3 spec)
3.85MHz @ 100MHz (exceeding 802.3 spec)
Unfortunately, this divisor makes the upper bound of both ranges exeed
the IEEE 802.3 specification, and thus we can not use it without knowing
for certain what the current CSR clock rate actually is.
So, STMMAC_CSR_60_100M is the best fit for all boards based on the
information provided thus far.
Link: https://lore.kernel.org/r/acGhQ0oui+dVRdLY@oss.qualcomm.com
Link: https://lore.kernel.org/r/acw1habUsiSqlrky@oss.qualcomm.com
Reviewed-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w8JKr-0000000EdLC-41Bt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are already 'if STMMAC_ETH' and 'STMMAC_PLATFORM'
conditions wrapping these config options, making the
'depends on' statements duplicate dependencies (dead code).
I propose leaving the outer 'if STMMAC_PLATFORM...endif' and
'if STMMAC_ETH...endif' conditions, and removing the
individual 'depends on' statements.
This dead code was found by kconfirm, a static analysis tool for Kconfig.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260402145858.240231-1-julianbraha@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The jumbo_frm() chain-mode implementation unconditionally computes
len = nopaged_len - bmax;
where nopaged_len = skb_headlen(skb) (linear bytes only) and bmax is
BUF_SIZE_8KiB or BUF_SIZE_2KiB. However, the caller stmmac_xmit()
decides to invoke jumbo_frm() based on skb->len (total length including
page fragments):
is_jumbo = stmmac_is_jumbo_frm(priv, skb->len, enh_desc);
When a packet has a small linear portion (nopaged_len <= bmax) but a
large total length due to page fragments (skb->len > bmax), the
subtraction wraps as an unsigned integer, producing a huge len value
(~0xFFFFxxxx). This causes the while (len != 0) loop to execute
hundreds of thousands of iterations, passing skb->data + bmax * i
pointers far beyond the skb buffer to dma_map_single(). On IOMMU-less
SoCs (the typical deployment for stmmac), this maps arbitrary kernel
memory to the DMA engine, constituting a kernel memory disclosure and
potential memory corruption from hardware.
Fix this by introducing a buf_len local variable clamped to
min(nopaged_len, bmax). Computing len = nopaged_len - buf_len is then
always safe: it is zero when the linear portion fits within a single
descriptor, causing the while (len != 0) loop to be skipped naturally,
and the fragment loop in stmmac_xmit() handles page fragments afterward.
Fixes: 286a837217 ("stmmac: add CHAINED descriptor mode support (V4)")
Cc: stable@vger.kernel.org
Signed-off-by: Tyllis Xu <LivelyCarpet87@gmail.com>
Link: https://patch.msgid.link/20260401044708.1386919-1-LivelyCarpet87@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the "TSO supported" message to stmmac_set_gso_features() so that
we group all probe-time TSO stuff in one place.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7pu8-0000000Eau5-3Zne@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Documentation states that TxPBL must be >= 4 to allow TSO support, but
the driver doesn't check this. TxPBL comes from the platform glue code
or DT. Add a check with a warning if platform glue code attempts to
enable TSO support with TxPBL too low.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7pu3-0000000Eatz-39ts@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a warning message if TSO is requested by the platform glue code but
the core wasn't configured for TSO.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7pty-0000000Eatt-2TjZ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make stmmac_set_gso_features() more readable by adding some whitespace
and getting rid of the indentation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptt-0000000Eatn-1ziK@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test in stmmac_xmit() to see whether we should pass the skbuff to
stmmac_tso_xmit() is more complex than it needs to be. This test can
be simplified by storing the mask of GSO types that we will pass, and
setting it according to the enabled features.
Note that "tso" is a mis-nomer since commit b776620651 ("net:
stmmac: Implement UDP Segmentation Offload"). Also note that this
commit controls both via the TSO feature. We preserve this behaviour
in this commit.
Also, this commit unconditionally accessed skb_shinfo(skb)->gso_type
for all frames, even when skb_is_gso() was false. This access is
eliminated.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptj-0000000Eatb-11zK@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a check in .ndo_features_check() to indicate whether hardware
checksum can be performed on the skbuff. Where hardware checksum is
not supported - either because the channel does not support Tx COE
or the skb isn't suitable (stmmac uses a tighter test than
can_checksum_protocol()) we also need to disable TSO, which will be
done by harmonize_features() in net/core/dev.c
This fixes a bug where a channel which has COE disabled may still
receive TSO skbuffs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7pte-0000000EatU-0ILt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
stmmac_tso_xmit() checks whether the skbuff is trying to offload
vlan tag insertion to hardware, which from the comment in the code
appears to be buggy when the TSO feature is used.
Rather than stmmac_tso_xmit() inserting the VLAN tag, handle this
in stmmac_features_check() which will then use core net code to
handle this. See net/core/dev.c::validate_xmit_skb()
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptY-0000000EatO-42Qv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the STM32MP151 documentation which covers dwmac v4.2, the
hardware TSO feature can handle header lengths up to a maximum of 1023
bytes.
Add a .ndo_features_check() method implementation to check the header
length meets these requirements, otherwise fall back to software GSO.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptO-0000000EatC-39il@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will need to compute the size of the protocol headers in two places,
so move this into a separate function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptJ-0000000Eat5-2ZlA@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
