Eqos ethernet support five queues on hardware, enable these queues and
configure the priority of each queue. Uses Strict Priority as scheduling
algorithms to ensure that the TSN function works.
The priority of each queue is a bitmask value that maps VLAN tag
priority to the queue. Since the hardware only supports five queues,
this patch maps priority 0-4 to queues one by one, and priority 5-7 to
queue 4.
The total fifo size of 5 queues is 8192 bytes, if enable 5 queues with
store-and-forward mode, it's not enough for large packets, which would
trigger fifo overflow frequently. This patch set DMA to thresh mode to
enable all 5 queues.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add overlays for various serdes protocols on LS1028A QDS board using
different PHY cards. These should be applied at boot, based on serdes
configuration. If no overlay is applied, only the RGMII interface on
the QDS is available in Linux.
Building device tree fragments requires passing the "-@" argument to
dtc, which increases the base dtb size and might cause some platforms to
fail to store the new binary. To avoid that, it would be nice to only
pass "-@" for the platforms where fragments will be used, aka
LS1028A-QDS. One approach suggested by Rob Herring is used here:
https://lore.kernel.org/patchwork/patch/821645/
Also moved the enet* override nodes in dts file to be in alphabetic order.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i2c rtc is on i2c2 bus not i2c1 bus, so fix it in dts.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.lil@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable pwm0 on ls1028a-rdb board which uses flextimer1.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add pwm nodes using flextimer controller.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add flextimer2 based ftm_alarm1 node and enable it to be the default rtc
wakeup source for rdb and qds boards instead of the original flextimer1
which is used by PWM. The ftm_alarm0 node hence is disabled by default.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCIe EP nodes for ls1028a to support EP mode.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add interrupt line for RTC node on lx2162a-qds
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The default NXP SDHC adapter cards for LX2162AQDS are SD 2.0/3.0
adapter card for eSDHC1, and eMMC 5.1 adapter card for eSDHC2.
Add speed modes properties supported by the two adapters in device
tree node.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable USB3 HW LPM feature for lx2160a.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The two external MDIO buses used to communicate with phy devices that
are external to SOC are muxed in LX2160AQDS board. These buses can be
routed to any one of the eight IO slots on LX2160AQDS board depending on
value in fpga register 0x54. Additionally the external MDIO1 is used to
communicate to the onboard RGMII phy devices. The mdio1 is controlled
by bits 4-7 of fpga register and mdio2 is controlled by bits 4-7 of fpga
register.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disabled by default in SoC dtsi and enables in board dts files.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The base i.MX8MM dtsi changes the audio PLL2 rate, which gets in the
way if it should be used for anything else than audio. As this PLL doesn't
seem to be used by any upstream supported board, just remove the rate
configuration to allow boards to set it up as they wish.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The slew rate and drive-strength of the i2c1 pads were much too
high. Bring them down to avoid signal quality issues.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing reset-gpios property to allow Linux to fully reset
the network PHY and fix the pinmux to add the neccessary pull-ups
for the PHY strap configuration.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'pm-ignore-notify' property is not a valid property and there is
no documentation for it.
Drop such invalid property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8ULP use scmi firmware based power domain and sensor support.
So add the firmware node and the sram it uses.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SW1C regulator powers the VPU and the state isn't guaranteed
to always be on. Link the VPU power-domain to the regulator to
ensure it is turned on before using the power domain.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This property could fix the defect that external usb device
always prints this error log --- 'reset SuperSpeed USB device number n
using xhci_hcd' when system power on.
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1088a has a separate reset register block. Define it in dts and use
it for reboot.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Company policy requires that copyright is updated when a file is
touched. Keeping the copyright change separate to reduce the noise in
other patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These are used by U-Boot, and are required for keeping the device trees
in sync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is used by U-Boot and is required for keeping the device trees in
sync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In preparation for this board's device tree synchronization with U-Boot,
we must find a common node ordering pattern. Alphabetical sounds about
right.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add mac address in efuse, so that EQOS driver can parse it from nvmem
cell.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unused "nvmem_macaddr_swap" property for FEC, there is no info in both
dt-binding and driver, so it's safe to remove it.
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to commit 0a4355c2b7 ("net: phy: realtek: add dt property to
disable CLKOUT clock"), diable CLKOUT clock for FEC PHY to save power on
i.MX8MP EVK board.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for TQMa8Mx module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for TQMa8MQNL module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for TQMa8MQML module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the basic dts file for i.MX8ULP EVK board.
Only the necessary devices for minimal system boot up are enabled:
enet, emmc, usb, console uart.
some of the devices' pin status may lost during low power mode,
so additional sleep pinctrl properties are included by default.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the basic dtsi support for i.MX8ULP.
i.MX 8ULP is part of the ULP family with emphasis on extreme
low-power techniques using the 28 nm fully depleted silicon on
insulator process. Like i.MX 7ULP, i.MX 8ULP continues to be
based on asymmetric architecture, however will add a third DSP
domain for advanced voice/audio capability and a Graphics domain
where it is possible to access graphics resources from the
application side or the realtime side.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The baseboard has support for a TDNext 5640 Camera which
uses an OV5640 connected to a 2-lane CSI2 interface.
With the CSI and mipi_csi2 drivers pointing to an OV5640 camera, the media
pipeline can be configured with the following:
media-ctl --links "'ov5640 1-003c':0->'imx7-mipi-csis.0':0[1]"
The camera and various nodes in the pipeline can be configured for UYVY:
media-ctl -v -V "'ov5640 1-003c':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -v -V "'csi':0 [fmt:UYVY8_1X16/640x480 field:none]"
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a csi bridge and csis interface that tie together
to allow csi2 capture.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8QXP A35 Cluster has 32KB Icache, 32KB Dcache and 512KB L2 Cache
- Icache is 2-way set associative
- Dcache is 4-way set associative
- L2cache is 8-way set associative
- Line size are 64bytes
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8QM A53 Cluster has 32KB Icache, 32KB Dcache and 1MB L2 Cache
- Icache is 2-way set associative
- Dcache is 4-way set associative
- L2cache is 16-way set associative
- Line size are 64bytes
A72 Cluster has 48KB Icache, 32KB Dcache and 1MB L2 Cache
- ICache is 3-way set-associative
- Dcache is 2-way set-associative
- L2Cache is 16-way set-associative
- Line size are 64bytes
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8M Family use A53 Cores and has 32KB ICache with 32KB DCache.
- Icache is 2-way set associative
- Dcache is 4-way set associative
- L2cache is 16-way set associative
- Line size are 64bytes
Except i.MX8MQ has 1MB L2 Cache, others has 512KB L2 Cache.
So add the cache info in device tree and let use could see that
from /sys/devices/system/cpu/cpu[x]/cache/
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The r3 and later revisions of the Librem 5 phone include an additional switch
to control the hi846 XSHUTDOWN pin. Describe it.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
