Match unit-address to reg entry to fix dtbs W=1 warnings:
Warning (simple_bus_reg): /soc/qrng@e1000: simple-bus unit address format error, expected "e3000"
Fixes: 5bf6356212 ("arm64: dts: ipq6018: Add a few device nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230419211856.79332-1-krzysztof.kozlowski@linaro.org
Set up and enable SDHCI2 to enable the microSD slot on Kumano
devices.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315-topic-kumano_dts0-v2-4-0ca7fa521b86@linaro.org
Sony - as per usual - used a whole bunch of GPIO-gated fixed
voltage regulators for camera sensors on Kumano. Describe them
and the corresponding pins.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315-topic-kumano_dts0-v2-3-0ca7fa521b86@linaro.org
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the common DTSI to better document the hardware.
The pin assignment for TLMM is identical on both devices. Great job!
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315-topic-kumano_dts0-v2-2-0ca7fa521b86@linaro.org
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the Griffin and Bahamut device trees to better document
the hardware.
They are the same on both devices! Very nice!
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315-topic-kumano_dts0-v2-1-0ca7fa521b86@linaro.org
Unlike typical GIC interrupts, first cell for SPMI interrupts is the
USID rather than GIC_SPI/GIC_PPI/GIC_LPI qualifier. Fix the resin
interrupt to use USID value 0x0 rather than GIC_SPI define.
Fixes: f86ae6f23a ("arm64: dts: qcom: sagit: add initial device tree for sagit")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230409182145.122895-1-dmitry.baryshkov@linaro.org
Add device tree bindings for the video clock controller on Qualcomm
SM8450 platform.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524140656.7076-2-quic_tdas@quicinc.com
Add node to support the QUP5 SPI controller inside of IPQ8074.
Some devices use this bus in order to manage external switches.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230426185647.180166-1-robimarko@gmail.com
Using interrupts-extended already indicates what the interrupt-parent
is, so drop the explicit interrupt-parent.
The comment about this being the phy-intr is not helpful either, since
this is the only interrupt in the phy node.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501212446.2570364-4-ahalaney@redhat.com
The property logically makes sense in decimal, and is the standard used
elsewhere.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501212446.2570364-3-ahalaney@redhat.com
As noted by Konrad while reviewing [1], fix the EUD and DWC3
node syntax in sc7280 dtsi file.
While at it also fix the errors reported by '$ make dtbs_check'
for the EUD node:
arch/arm64/boot/dts/qcom/sc7280-crd-r3.dtb: eud@88e0000: ports:
'oneOf' conditional failed, one must be fixed:
'port' is a required property
'#address-cells' is a required property
'#size-cells' is a required property
From schema: Documentation/devicetree/bindings/soc/qcom/qcom,eud.yaml
[1]. https://lore.kernel.org/linux-arm-msm/20221231131945.3286639-1-bhupesh.sharma@linaro.org
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230502093959.1258889-2-bhupesh.sharma@linaro.org
Introduce sdam_2 node, which is to be used via nvmem for power on
reasons during reboot. Add supported PoN reasons supported via sdam_2
node.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-upstream-reboot-reason-v1-2-c5ac3dd5b49f@linaro.org
Introduce sdam_2 node, which is to be used via nvmem for power on
reasons during reboot. Add supported PoN reasons supported via sdam_2
node.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-upstream-reboot-reason-v1-1-c5ac3dd5b49f@linaro.org
Now as both lt9611 and drm/msm drivers were updated to handle the 4k
modes over DSI, enable "bonded" DSI mode on DB845c. This way the board
utilizes both DSI links and thus can support 4k on the HDMI output.
Cc: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230504160430.4014206-1-dmitry.baryshkov@linaro.org
Card-Detect (CD) gpio for SDHC2 is an active GPIO line. Fix the same.
This allows the uSD card to be properly detected on the board.
Fixes: 8d58a8c0d9 ("arm64: dts: qcom: Add base qrb4210-rb2 board dts")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516075908.2323372-3-bhupesh.sharma@linaro.org
The RB2 has a HDMI output via an LT9611UXC bridge. Set it up.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-and-Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515-topic-rb2-bits-v1-2-a52d154a639d@linaro.org
The board hosts a whole lot of fixed regulators. Describe them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-and-Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515-topic-rb2-bits-v1-1-a52d154a639d@linaro.org
Add missing parts of USB stack to enable USB OTG mode. The QRD8550
comes with one USB Type-C port.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516133011.108093-2-krzysztof.kozlowski@linaro.org
Add PCIe0 nodes used with WCN7851 device. The PCIe1 is not connected,
thus skip pcie_1_phy_aux_clk input clock to GCC.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516133011.108093-1-krzysztof.kozlowski@linaro.org
With support for the QMP combo phy to react to USB Type-C switch events,
introduce it as the next hop for the SuperSpeed lanes of the Type-C
connector, and connect the output of the DisplayPort controller
to the QMP combo phy.
This allows the TCPM to perform orientation switching of both USB and
DisplayPort signals.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-graphics-dp-next-v3-4-6c43d293995f@linaro.org
With support for the QMP combo phy to react to USB Type-C switch events,
introduce it as the next hop for the SuperSpeed lanes of the Type-C
connector, and connect the output of the DisplayPort controller
to the QMP combo phy.
This allows the TCPM to perform orientation switching of both USB and
DisplayPort signals.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-graphics-dp-next-v3-3-6c43d293995f@linaro.org
Following the CRD, connect the two QMP phys inbetween the USB Type-C
connectors and the DisplayPort controller, to handle orientation
switching.
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515032743.400170-9-quic_bjorande@quicinc.com
With support for the QMP combo phy to react to USB Type-C switch events,
introduce it as the next hop for the SuperSpeed lanes of the two USB
Type-C connectors, and connect the output of the DisplayPort controller
to the QMP combo phy.
This allows the TCPM to perform orientation switching of both USB and
DisplayPort signals.
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515032743.400170-8-quic_bjorande@quicinc.com
Update the size of GICC and GICV regions to 8kB as the GICC_DIR & GICV_DIR
registers lie in the second 4kB region. Also, add target CPU encoding.
Fixes: 97cb36ff52 ("arm64: dts: qcom: Add ipq9574 SoC and AL02 board support")
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230425084010.15581-2-quic_devipriy@quicinc.com
We need more granularity for things like the GPU. Add the missing levels.
This unfortunately requires some re-indexing, resulting in an ugly diff.
Rename the nodes to prevent that in the future.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230517-topic-kailua-rpmhpd-v2-3-3063ce19c491@linaro.org
After adding the missing levels with a nice, easy-to-read diff,
reformat the defines to make them nice to look at..
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230517-topic-kailua-rpmhpd-v2-2-3063ce19c491@linaro.org
There are a lot of RPMh levels that we haven't included yet.. some
sadly turned out to be necessary, add them!
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230517-topic-kailua-rpmhpd-v2-1-3063ce19c491@linaro.org
The UFS controller is cache coherent, so mark it as such in the dtsi.
Fixes: be543efeee ("arm64: dts: qcom: sa8775p: add UFS nodes")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515121908.303432-1-brgl@bgdev.pl
GIC child node is supposed to be named msi-controller:
sa8295p-adp.dtb: interrupt-controller@17a00000: gic-its@17a40000: False schema does not allow
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417080939.28648-3-krzysztof.kozlowski@linaro.org
Qualcomm PCI express root complex does not use snps,dw-pcie fallback:
['qcom,pcie-sm8150', 'snps,dw-pcie'] is too long
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417080939.28648-2-krzysztof.kozlowski@linaro.org
Since commit 6c84bbd103 ("dt-bindings: arm-smmu: Add generic
qcom,smmu-500 bindings") the SMMU is supposed to use qcom,smmu-500
compatible fallback.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417080939.28648-1-krzysztof.kozlowski@linaro.org
Drop incorrect and unused serial properties - address/size-cells and
reg-names:
sa8155p-adp.dtb: geniqup@ac0000: serial@a84000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'reg-names' were unexpected)
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417080818.28398-1-krzysztof.kozlowski@linaro.org
