Currently all users of the bridge-connector must call
drm_connector_attach_encoder() immediately after a successful
drm_bridge_connector_init().
This is an unnecessary burden for users. Move the call to the end of
drm_bridge_connector_init() so all callers can be simplified.
Update documentation accordingly, rewording a bit the whole paragraph which
would otherwise become poorly readable due to the growing list of actions.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260423-drm-bridge-connector-attach_encoder-v2-1-2ae6ca69b390@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
When Nouveau boots with GSP-RM, it bypasses several traditional code
paths to allow GSP-RM to handle those features. In particular,
some VBIOS parsing is skipped, and a side effect is that the VBIOS
is not exposed in the DRM debugfs entries.
Fix this by updating the drm BIOS struct (nvbios) with the VBIOS data
from the nvkm BIOS struct (nvkm_bios). This happens normally in
NVInitVBIOS(), but that function is skipped when booting with GSP-RM.
Signed-off-by: Timur Tabi <ttabi@nvidia.com>
Link: https://patch.msgid.link/20260428202825.1123719-1-ttabi@nvidia.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
We have a helper drm_printf_indent() for tab indenting the prints. It
makes the actual strings more readable, and highlights the indented
parts better in source.
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Link: https://patch.msgid.link/20260408082211.3040194-2-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We have a helper drm_printf_indent() for tab indenting the prints. It
makes the actual strings more readable, and highlights the indented
parts better in source.
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Link: https://patch.msgid.link/20260408082211.3040194-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add configurable frequency limits to allow users to constrain the NPU
operating frequency range for power and thermal management. This support
requires firmware API version 3.34.0 or newer.
New sysfs interface:
The freq/ subdirectory contains the following attributes:
- hw_min_freq: Minimum frequency supported by hardware (read-only)
- hw_max_freq: Maximum frequency supported by hardware (read-only)
- hw_efficient_freq: Hardware's optimal operating frequency (read-only)
- current_freq: Current NPU frequency in MHz (read-only)
- set_min_freq: Configure minimum operating frequency (50XX+ devices)
- set_max_freq: Configure maximum operating frequency (50XX+ devices)
Legacy attributes npu_max_frequency_mhz and npu_current_frequency_mhz
are maintained for backward compatibility.
Implementation details:
- Frequency configuration is communicated to firmware via JSM messages
- User-specified frequency values are clamped to hardware limits
- Power-efficient frequency (pn_ratio) is adjusted dynamically to stay
within the configured range
- Frequency configuration is initialized during device boot
- The JSM API header is updated to version 3.34.0 to support the new
VPU_JSM_MSG_FREQ_CONFIG firmware message
Added description for the sysfs attributes in the Documentation/ABI.
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Link: https://patch.msgid.link/20260408150152.2093638-1-andrzej.kacprowski@linux.intel.com
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251031102020.95349-3-marco.crivellari@suse.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
system_unbound_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
Adding system_dfl_wq to encourage its use when unbound work should be used.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20251031102020.95349-2-marco.crivellari@suse.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
The system efficiency factor is used for QoS calculation. Change it to 2
to account for the efficiency overhead.
Signed-off-by: Nishad Saraf <nishads@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260424040824.2253607-3-lizhi.hou@amd.com
The QoS request provided when creating a hardware context is currently
ignored when operating in temporal-only mode. Change this to use resource
allocation through xrs_allocate_resource(), which sets the default DPM
level according to the QoS request.
When multiple hardware contexts are active, track their required DPM
levels and set the default DPM level to the highest among them.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260424040824.2253607-1-lizhi.hou@amd.com
Param used for setting FW trace mask at module load time. Other debugfs
entry exist to allow update at run time.
Signed-off-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Reviewed-by: Alessio Belle <alessio.belle@imgtec.com>
Link: https://patch.msgid.link/20260427-ftrace_fix-v3-2-e081530759a8@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Raspberry Pi 3B by marking the VEC clk critical so it doesn't get
turned off and hang the bus.
-----BEGIN PGP SIGNATURE-----
iQJIBAABCAAyFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAmnuTSsUHHN3Ym95ZEBj
aHJvbWl1bS5vcmcACgkQrQKIl8bklSUtpw//UbUCefvtSuj7UJLqgZXZgZvos9hU
kQO0kt+wsZCx0w3vKjJojW7E8IiITJDWzVDq6Ib6dVvpoLy0sOvSCbmKrcYLOjaf
kBXAvPHrpBNDDgRD+z3Ci9Sz8Dk9N+x7vQYvXGpUDbGY+dYAx8NGjdbSMqmQofC1
CWYgneh16hUYN8dgZOXC3fZmj4wHt4DGAS3f+uVWML1cLIDv5JR31SAu5i3htgxr
8JUDsBiM2quAjgV81Qp9B102hQGdKBW8AquUnknwtegja6+Go59x2/5jlvE0wjQJ
6Hf7eyUL6PgiAUEGiebLPMKgY6FWT9FtYCuuSqC84EiB5iiLr1MZBX5JsdJ15QRq
fogaABOJxvzy7XnVk0ELqNzn5/uJ/UDPFJkm2RUOUENswi4QuW3O9vJANKTFdUq4
CSz4JO5nqAe+gIbrURl+H8G50nWDHdId69uimbrhZst1E3sue9xDI9G7VwBTTf/8
o+8ylQkfWhGlSMq8yOMTTqUqk5O+uzfEYUYQ7EdzDknuoEsFh1Fy7UpzBLIqVdjd
WylzH9zOdVEI/OUuGmKOJHXy1amGBEV5EISvMRplLyB3R/mFWvIe5kZ4NhtrL9b0
zMjVShkrOP4X4ydOkz6l6oNwgBG+pnosewbwsSYKzSiF5czaXfv96UrQ1J/JNj27
X1Qr/BuY1E2dz0k=
=JtUn
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the merge window to avoid a boot hang on
Raspberry Pi 3B by marking the VEC clk critical so that it
doesn't get turned off and hang the bus"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: bcm: rpi: Mark VEC clock as CLK_IGNORE_UNUSED
