Connector detection using poll method won't work in case of bridge
attached to the encoder with the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR, as
the code defaults to HPD.
Enable DRM_BRIDGE_OP_HPD based on HPD interrupt availability, so that
it will fall back to polling, if HPD is not available.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419142453.48839-1-biju.das.jz@bp.renesas.com
Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
This driver is written without any documentation from Lontium and based
only on shreds of information available in various obscure example codes,
hence long runs of unknown register patches and lengthy delays in various
places. Whichever register meaning could be divined from its behavior has
at least a comment around it.
Currently the only mode tested is Single-link DSI to Single-link LVDS.
Dual-link LVDS might work as well, the register programming is in place,
but is untested.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-2-marex@denx.de
Add bindings for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-1-marex@denx.de
Speaker may share I2S with DP and .get_eld callback will be called when
speaker is playing. When HDMI wans't connected, the connector will be
null. Instead of return an error, fill in empty ELD.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414090003.1806535-1-hsinyi@chromium.org
Soft reset the display subsystem controller on startup and wait for
the reset to complete. This helps the scenario where display was
already in use by some other core before the linux was booted.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220314113739.18000-1-devarsht@ti.com
drm/drm-next has a build fix for the NewVision NV3052C panel
(drivers/gpu/drm/panel/panel-newvision-nv3052c.c), which needs to be
merged back to drm-misc-next, as it was failing to build there.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Smatch reports this issue
gf108.c:147:1: warning: symbol 'gf108_gr_fwif'
was not declared. Should it be static?
gf108_gr_fwif is only used in gf108.c. Single
file variables should not be global so change
gf108_gr_fwif's storage-class specifier to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220418152810.3280502-1-trix@redhat.com
Smatch reports this issue
base917c.c:26:1: warning: symbol 'base917c_format'
was not declared. Should it be static?
base917c_format is only used in base917.c. Single
file variables should not be global so change
base917c_format's storage-class specifier to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220418141842.296386-1-trix@redhat.com
In function do_remove_conflicting_framebuffers, if device is NULL, there
will be null pointer reference. The patch add a check to the if expression.
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220210065824.368355-1-zhouzhouyi@gmail.com
Factor out from drm_dp_dpcd_read() a function to probe a DPCD address
with a 1-byte read access. This will be needed by the next patch doing a
read from an LTTPR address, which must happen without the preceding
wake-up read in drm_dp_dpcd_read().
While at it add tracing for the 1 byte read even if the read was
successful.
v2: Add a probe function instead of exporting drm_dp_dpcd_access(). (Jani)
v3: Add tracing for the 1-byte read even if the read was successful. (Khaled)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411132539.984647-1-imre.deak@intel.com
Add some helpers to figure out the EDID extension block count, block
count, size, pointers to blocks.
Unfortunately, we'll need to cast away the const in a few places where
we actually need to access the data.
v3: fix (!edid_extension_block_count(edid) == 0) (kernel test robot)
v2: fix s/j/i/ introduced in a rebase
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/dc7b0850293d837439fb3914c8a9d81e39018b4b.1649685475.git.jani.nikula@intel.com
Convert drm_do_get_edit() from the base block read helper to the generic
block read helper. There's quite a bit going on here, as the corrupt and
null EDID information is moved back to the caller. As we see, they were
not all that clear to begin with, and this change underlines that.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3bcf98453770757ee93386da0cfbc6552d42a312.1649685475.git.jani.nikula@intel.com
We have an abstraction for the EDID base block read, yet duplicating the
retries and error handling for extension block reads. Introduce a more
generic EDID block read helper.
Switch to the helper piecemeal, starting with drm_edid_get_panel_id(),
which doesn't need or have access to the connector anyway.
The subtle change is switching from drm_edid_block_valid() to
edid_block_check(). We also status print once, not for every attempt.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/47560f7530e4a7b32b56cb9038178244fe30a4af.1649685475.git.jani.nikula@intel.com
Split out a function to log EDID block status. The printouts get changed
slightly.
Unfortunately, not all users will have struct drm_device available, so
we convert to pr_* debug logging instead of drm device based logging.
v2: Complain more loudly about unknown status codes (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/98d12db95e55e2e18548822078ec3b16ae006732.1649685475.git.jani.nikula@intel.com
I messed up the delayed takover path in the locking conversion in
6e7da3af00 ("fbcon: Move console_lock for register/unlink/unregister").
If CONFIG_FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER is enabled, fbcon take-over
doesn't take place when calling fbcon_fb_registered(). Instead, is deferred
using a workqueue and its fbcon_register_existing_fbs() function calls to
fbcon_fb_registered() again for each registered fbcon fb.
This leads to the console_lock tried to be held twice, causing a deadlock.
Fix it by re-extracting the lockless function and using it in the
delayed takeover path, where we need to hold the lock already to
iterate over the list of already registered fb. Well the current code
still is broken in there (since the list is protected by a
registration_lock, which we can't take here because it nests the other
way round with console_lock), but in the future this will be a list
protected by console_lock when this is all sorted out.
While reviewing the broken commit I realized that I've left some
outdated comments about the locking behind. Fix those too.
v2: Improve commit message (Javier)
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Fixes: 6e7da3af00 ("fbcon: Move console_lock for register/unlink/unregister")
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Du Cheng <ducheng2@gmail.com>
Cc: Claudio Suarez <cssk@net-c.es>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Zheyu Ma <zheyuma97@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Helge Deller <deller@gmx.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220413082128.348186-1-daniel.vetter@ffwll.ch
This driver currently rewrites bus_flags based solely on the value of
DT property 'data-mirror' and ignores bus_flags which might have been
set in DT panel-timing node. Specificaly, the 'de-active' DT property
sets DRM_BUS_FLAG_DE_ bus_flags.
Since of_get_drm_panel_display_mode() conveniently parses the bus_flags
out of DT panel-timing property, just ORR them with bus_flags inferred
from 'data-mirror' DT property and use the result as panel bus_flags.
This fixes handling of panels with 'panel-timing { de-active = <1>; };'.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220401162154.295152-2-marex@denx.de
The mode parsing is currently implemented in three steps:
of_get_display_timing() - DT panel-timing to struct display_timing
videomode_from_timing() - struct display_timing to struct videomode
drm_display_mode_from_videomode() - struct videomode to struct drm_display_mode
Replace all that with simple of_get_drm_panel_display_mode() call,
which already populates struct drm_display_mode and then duplicate
that mode in panel_lvds_get_modes() each time, since the mode does
not change.
Nice bonus is the bus_flags parsed by of_get_drm_panel_display_mode()
out of panel-timing DT node, which is used in subsequent patch to fix
handling of 'de-active' DT property.
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220401162154.295152-1-marex@denx.de
To make debugging easier, convert driver to regmap. Implement read and write
regmap tables for known registers, keep all known register readable and mark
those which are obviously read-only as not writeable.
Use common I2C regmap for the I2C configuration, implement custom regmap bus
for DSI configuration. The later is mandatory as this chip requires one extra
byte set to read access length between register address and data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220403171004.368464-1-marex@denx.de
Let's make sure FBC is always disabled when we start to take
over the hardware state.
I suspect this should never really happen, since the only time
when we really should be taking over with the display already
active is when the previous state was progammed by the BIOS,
which likely shouldn't use FBC. This could be driver init,
or S4 resume when the boot kernel doesn't load i915. But I
suppose no harm in keeping this code around for exra safety
since it's quite trivial.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315140001.1172-7-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
By the time intel_fbc_global_disable() gets called during driver
teardown we should have already disabled all the crtcs, so
no way FBC should be enabled at this point.
And I have no idea what the other user (i915_restore_display())
is even trying to achieve.
So let's just throw intel_fbc_global_disable() into the bin.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315140001.1172-6-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Don't issue a nuke from frontbuffer flush while a flip is pending.
This avoids the DSPADDR/DSPSURF rmw abuse from the pre-snb nuke
from racing with the DSPADDR/DSPSURF write being performed by
the flip/plane update. The flip itself will already cause the nuke
so a double nuke is redundant.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315140001.1172-4-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Not sure what the point of this fbc->possible_frontbuffer_bits is.
And especially don't see why it's returning all the bits when
fbc is not even enabled. So let's just get rid of this and only
say we are interested in the plane's frontbuffer bits when fbc
is actually enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315140001.1172-2-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
It looks like we still need to call dma_fence_put() on the man->move,
otherwise we just end up leaking it, leading to fireworks later.
v2(Daniel):
- Simplify the function tail
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5689
Fixes: 8bb3158782 ("drm/ttm: remove bo->moving")
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220413082133.272445-1-matthew.auld@intel.com
With some VRR panels, user can turn VRR ON/OFF on the fly from the panel settings.
When VRR is turned OFF ,sends a long HPD to the driver clearing the Ignore MSA bit
in the DPCD. Currently the driver parses that onevery HPD but fails to reset
the corresponding VRR Capable Connector property.
Hence the userspace still sees this as VRR Capable panel which is incorrect.
Fix this by explicitly resetting the connector property.
v2: Reset vrr capable if status == connector_disconnected
v3: Use i915 and use bool vrr_capable (Jani Nikula)
v4: Move vrr_capable to after update modes call (Jani N)
Remove the redundant comment (Jan N)
v5: Fixes the regression on older platforms by resetting the VRR
only if HAS_VRR
v6: Remove the checks from driver, add in drm core before
setting VRR prop (Ville)
v7: Move VRR set/reset to set/unset_edid (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 9bc34b4d0f ("drm/i915/display/vrr: Reset VRR capable property on a long hpd")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303233222.4698-1-manasi.d.navare@intel.com
Add support for the DG2 specific render compression with clear color
framebuffer format.
DG2 onwards discrete gfx has support for new flat CCS mapping,
which brings in display feature in to avoid Aux walk for compressed
surface. This support build on top of Flat CCS support added in XEHPSDV.
FLAT CCS surface base address should be 64k aligned,
Compressed displayable surfaces must use tile4 format.
HAS: 1407880786
B.Spec : 7655
B.Spec : 53902
v2: Merge all bits required for the support of functionality into this
patch from the patch adding the corresponding modifier.
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411143405.1073845-5-imre.deak@intel.com
DG2 clear color render compression uses Tile4 layout. Therefore, we need
to define a new format modifier for uAPI to support clear color rendering.
v2:
Display version is fixed. [Imre]
KDoc is enhanced for cc modifier. [Nanley & Lionel]
v3:
Split out the modifier addition to a separate patch.
Clarify the modifier layout description.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Nanley Chery <nanley.g.chery@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411143405.1073845-4-imre.deak@intel.com
Add support for DG2 render and media compression, for the description of
buffer layouts see the previous patch adding the corresponding
frame buffer modifiers.
v2:
Display version fix [Imre]
v3:
Split out modifier addition to separate patch.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411143405.1073845-3-imre.deak@intel.com
The render/media engines on DG2 unify render compression and media
compression into a single format for the first time, using the Tile 4
layout for main surfaces. The compression algorithm is different from
any previous platform and the display engine must still be configured to
decompress either a render or media compressed surface; as such, we
need new RC and MC framebuffer modifiers to represent buffers in this
format.
v2: Clarify modifier layout description.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Nanley Chery <nanley.g.chery@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411143405.1073845-2-imre.deak@intel.com
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- atomic: Add atomic_print_state to private objects
- edid: Constify the EDID parsing API, rework of the API
- dma-buf: Add dma_resv_replace_fences, dma_resv_get_singleton, make
dma_resv_excl_fence private
- format: Support monochrome formats
- fbdev: fixes for cfb_imageblit and sys_imageblit, pagelist
corruption fix
- selftests: several small fixes
- ttm: Rework bulk move handling
Driver Changes:
- Switch all relevant drivers to drm_mode_copy or drm_mode_duplicate
- bridge: conversions to devm_drm_of_get_bridge and panel_bridge,
autosuspend for analogix_dp, audio support for it66121, DSI to DPI
support for tc358767, PLL fixes and I2C support for icn6211
- bridge_connector: Enable HPD if supported
- etnaviv: fencing improvements
- gma500: GEM and GTT improvements, connector handling fixes
- komeda: switch to plane reset helper
- mediatek: MIPI DSI improvements
- omapdrm: GEM improvements
- panel: DT bindings fixes for st7735r, few fixes for ssd130x, new
panels: ltk035c5444t, B133UAN01, NV3052C
- qxl: Allow to run on arm64
- sysfb: Kconfig rework, support for VESA graphic mode selection
- vc4: Add a tracepoint for CL submissions, HDMI YUV output,
HDMI and clock improvements
- virtio: Remove restriction of non-zero blob_flags,
- vmwgfx: support for CursorMob and CursorBypass 4, various
improvements and small fixes
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYk6nlQAKCRDj7w1vZxhR
xaTTAP0ZeeXRWIYxFfmuEAUd3H4ztvr3cx/QU/85qMXQUM4gSgD/cvQHMeucrFlX
2Bafjzl/p1tQrth0HNOkSz85dABUUws=
=rJSD
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-04-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.19:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- atomic: Add atomic_print_state to private objects
- edid: Constify the EDID parsing API, rework of the API
- dma-buf: Add dma_resv_replace_fences, dma_resv_get_singleton, make
dma_resv_excl_fence private
- format: Support monochrome formats
- fbdev: fixes for cfb_imageblit and sys_imageblit, pagelist
corruption fix
- selftests: several small fixes
- ttm: Rework bulk move handling
Driver Changes:
- Switch all relevant drivers to drm_mode_copy or drm_mode_duplicate
- bridge: conversions to devm_drm_of_get_bridge and panel_bridge,
autosuspend for analogix_dp, audio support for it66121, DSI to DPI
support for tc358767, PLL fixes and I2C support for icn6211
- bridge_connector: Enable HPD if supported
- etnaviv: fencing improvements
- gma500: GEM and GTT improvements, connector handling fixes
- komeda: switch to plane reset helper
- mediatek: MIPI DSI improvements
- omapdrm: GEM improvements
- panel: DT bindings fixes for st7735r, few fixes for ssd130x, new
panels: ltk035c5444t, B133UAN01, NV3052C
- qxl: Allow to run on arm64
- sysfb: Kconfig rework, support for VESA graphic mode selection
- vc4: Add a tracepoint for CL submissions, HDMI YUV output,
HDMI and clock improvements
- virtio: Remove restriction of non-zero blob_flags,
- vmwgfx: support for CursorMob and CursorBypass 4, various
improvements and small fixes
[airlied: fixup conflict with newvision panel callbacks]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407085940.pnflvjojs4qw4b77@houat
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-23-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Initialize on-stack modes with drm_mode_init() to guarantee
no stack garbage in the list head, or that we aren't copying
over another mode's list head.
Based on the following cocci script, with manual fixups:
@decl@
identifier M;
expression E;
@@
- struct drm_display_mode M = E;
+ struct drm_display_mode M;
@@
identifier decl.M;
expression decl.E;
statement S, S1;
@@
struct drm_display_mode M;
... when != S
+ drm_mode_init(&M, &E);
+
S1
@@
expression decl.E;
@@
- &*E
+ E
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-22-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
In addition to the fp_timing,dvo_timing,panel_pnp_id tables
there also exists a panel_name table. Unlike the others this
is just one offset+table_size even though there are still 16
actual panel_names in the data block.
The panel_name table made its first appearance somewhere
around VBT version 156-163. The exact version is not known.
But we don't need to know that since we can just check whether
the pointers block has enough room for it or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405173410.11436-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
