Lenovo Yoga Pro 7 15ASH11 with AMD RYZEN AI MAX+ 388 (Strix Halo, ACP
7.0) uses Realtek ALC287 series codec. The ALC269_FIXUP_LENOVO_XPAD_ACPI
in alc269_fixup_vendor_tbl[] can load lenovo_wmi_hotkey_utilities module
by default in this laptop, but the driver doesn't control mic mute LED.
If users run below command and the mic mute LED can work normally.
$sudo echo 'Capture Switch' >/sys/class/sound/ctl-led/mic/card1/attach
After added the SND_PCI_QUIRK quirk special for Lenovo Yoga Pro 7
15ASH11, the mic mute LED works well.
Fixes: 83dca2530f ("ALSA: hda/realtek: ALC269 fixup for Lenovo Yoga Pro 7 15ASH111 audio")
Signed-off-by: Jackie Dong <xy-jackie@139.com>
Link: https://patch.msgid.link/20260527130353.5658-1-xy-jackie@139.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to a hardware defect, for Loongson PCI HDMI devices with a reversion
ID of 2, the pin sense status must be determined via the ELD.
Add a codec flag, eld_jack_detect, to indicate this case, and do special
handlings in read_pin_sense().
Cc: stable@vger.kernel.org
Signed-off-by: Baoqi Zhang <zhangbaoqi@loongson.cn>
Signed-off-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/20260527140841.3407183-1-chenhuacai@loongson.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 21.5" Retina 4K iMac (Late 2015, DMI product name "iMac16,1") ships
with a Cirrus Logic CS4208 codec wired to an external speaker amplifier
enabled through codec GPIO0 -- the same arrangement as the late-2013
MacBookPro 11,x. Without a matching entry in cs4208_mac_fixup_tbl[] the
fixup picker logs:
snd_hda_codec_cs420x hdaudioC1D0: CS4208: picked fixup for codec SSID 106b:0000
i.e. an empty fixup name, GPIO0 stays low, the external amp is never
powered up, and the internal speakers are silent on a stock kernel.
The codec SSID reported by hardware is 0x106b:0x7f00. Reusing CS4208_MBP11
(GPIO0 + SPDIF switch fixup) makes the internal speakers and S/PDIF
output work out of the box, removing the need for users to set
`options snd_hda_intel model=mbp11` via /etc/modprobe.d/.
Tested on iMac16,1 (kernel 6.17.0): four internal drivers
(Left tweeter, Left woofer, Right tweeter, Right woofer, exposed as the
4 channels of the analog-surround-40 ALSA profile) produce audio after
the fixup is applied.
Signed-off-by: Jakub Pisarczyk <pisarz77@gmail.com>
Link: https://patch.msgid.link/20260526201830.34097-1-pisarz77@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Troy Mitchell <troy.mitchell@linux.spacemit.com> says:
On some SoCs (e.g. SpacemiT K3), multiple I2S controllers share the
same physical BCLK. When one controller is already streaming, the
others must use hw_params that result in the same BCLK rate, otherwise
the shared clock would be reconfigured and corrupt the active stream.
This series adds framework-level support for this constraint:
Patch 1 adds the dt-bindings for the spacemit,k3-i2s compatible.
The K3 SoC uses the same I2S IP as K1 but requires additional clocks:
a dedicated sysclk_div, along with c_sysclk and c_bclk which are
shared across multiple I2S controllers.
Patch 2 adds a DEFINE_GUARD wrapping snd_soc_card_mutex_lock() and
snd_soc_card_mutex_unlock() so that scope-based locking picks up the
SND_SOC_CARD_CLASS_RUNTIME lockdep subclass.
Patch 3 adds the constraint logic in soc-pcm.c. During PCM open,
every DAI that has a bclk clock pointer gets a hw_rule registered
unconditionally. The rule callback runs at hw_refine time: it scans
the card for an active peer sharing the same physical BCLK (via
clk_is_match()) that has already completed hw_params, then constrains
the current stream's rate to match the established BCLK rate. The
first DAI to complete hw_params is unconstrained; subsequent DAIs
must match. Two modes are supported:
- Default (I2S): BCLK = rate * channels * sample_bits. The rule
derives the valid rate range from the current channel and
sample_bits intervals.
- Explicit ratio (TDM): if the driver sets dai->bclk_ratio
(e.g. slots * slot_width), the rule computes the single valid
rate as active_bclk_rate / bclk_ratio.
This series was prompted by review feedback on the SpacemiT K3 I2S
series, where a vendor-specific fixed-sample-rate property was rejected
in favor of a generic framework solution:
https://lore.kernel.org/all/afFqgF6ZRwYdfUmL@sirena.co.uk/
Link: https://patch.msgid.link/20260522-i2s-same-blk-v4-0-a71a86faaa20@linux.spacemit.com
The internal mic boost on the Positivo DN140 is too high.
Fix this by applying the ALC269_FIXUP_LIMIT_INT_MIC_BOOST fixup to the machine
to limit the gain.
Signed-off-by: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>
Link: https://patch.msgid.link/20260524185324.28959-1-edson.drosdeck@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cs35l56_hda_read_acpi() gets an allocated ACPI _SUB string from
acpi_get_subsystem_id(). On success, that string is used to create the
firmware system name.
Several error paths after the _SUB lookup can return without releasing
the allocated string. This includes speaker ID lookup errors other than
-ENOENT, and errors after a firmware system name has been allocated.
Use scoped cleanup for the temporary _SUB string and make
cs35l56->system_name device-managed. This releases the temporary _SUB
string on every error path and lets devres release the firmware system
name on probe failure and device removal.
Fixes: 6f03b446cb ("ALSA: hda: cs35l56: Add support for speaker id")
Fixes: 40b1c2f9b2 ("ALSA: hda/cs35l56: Workaround bad dev-index on Lenovo Yoga Book 9i GenX")
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260522-alsa-cs35l56-system-name-leak-v4-1-a6154dd09cd9@gmail.com
The BIOS on the Lenovo Yoga Slim 7 14AGP11 (AMD Ryzen AI / Kraken
Point chassis; board LNVNB161216, product 83QS) programs the PCI
subsystem ID of the HDA function as 17aa:0000. As a result no entry
in alc269_fixup_tbl[] matches via SND_PCI_QUIRK, the fixup falls back
to the generic auto-routing path, and the bass speaker pin is left
mis-routed. Laptop speakers sound noticeably thin.
The codec's own internal subsystem ID register reports 0x17aa394c
correctly, so an HDA_CODEC_QUIRK entry (which matches on the codec
SSID rather than on the PCI SSID) binds the chassis to the existing
ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN fixup. This mirrors the same
workaround already in place for the closely-related Yoga 7 2-in-1
14AKP10 and 16AKP10 entries earlier in the table.
With this change the kernel log goes from
ALC287: picked fixup for PCI SSID 17aa:0000
to
ALC287: picked fixup alc287-yoga9-bass-spk-pin
and speaker routing matches what the firmware intended. Verified by
the reporter against the equivalent modprobe override
(model=,alc287-yoga9-bass-spk-pin).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221438
Signed-off-by: Kris Kater <kris@kater.nu>
Link: https://patch.msgid.link/20260522060902.9423-1-kris@kater.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The comment for the pin configuration 0x21 in the fixup
ALC299_FIXUP_PREDATOR_SPK states "use as headset mic, without its own
jack detect", but the fixup name and the actual usage indicate that the
pin is meant to be used as internal speaker. Correct the comment to
avoid confusion.
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Link: https://patch.msgid.link/20260522060742.1384390-1-zhangheng@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com> says:
This series is a preparation for
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index 23ff24080dfd..aebd3a5e90af 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -477,7 +477,11 @@ struct rpmsg_device_id {
struct i2c_device_id {
char name[I2C_NAME_SIZE];
- kernel_ulong_t driver_data; /* Data private to the driver */
+ union {
+ /* Data private to the driver */
+ kernel_ulong_t driver_data;
+ const void *driver_data_ptr;
+ };
};
/* pci_epf */
and this requires that .driver_data is assigned via a named initializer
for static data. This requirement isn't a bad one because named
initializers are also much better readable than list initializers.
The union added to struct i2c_device_id enables further cleanups like:
diff --git a/drivers/iio/accel/kxcjk-1013.c b/drivers/iio/accel/kxcjk-1013.c
index 8a082ff034dd..b2aac7348d22 100644
--- a/drivers/iio/accel/kxcjk-1013.c
+++ b/drivers/iio/accel/kxcjk-1013.c
@@ -1429,7 +1429,7 @@ static int kxcjk1013_probe(struct i2c_client *client)
if (id) {
name = id->name;
- data->info = (const struct kx_chipset_info *)(id->driver_data);
+ data->info = id->driver_data_ptr;
} else {
name = iio_get_acpi_device_name_and_data(&client->dev, &ddata);
data->info = ddata;
@@ -1630,11 +1630,11 @@ static const struct dev_pm_ops kxcjk1013_pm_ops = {
};
static const struct i2c_device_id kxcjk1013_id[] = {
- { .name = "kxcjk1013", .driver_data = (kernel_ulong_t)&kxcjk1013_info },
- { .name = "kxcj91008", .driver_data = (kernel_ulong_t)&kxcj91008_info },
- { .name = "kxtj21009", .driver_data = (kernel_ulong_t)&kxtj21009_info },
- { .name = "kxtf9", .driver_data = (kernel_ulong_t)&kxtf9_info },
- { .name = "kx023-1025", .driver_data = (kernel_ulong_t)&kx0231025_info },
+ { .name = "kxcjk1013", .driver_data_ptr = &kxcjk1013_info },
+ { .name = "kxcj91008", .driver_data_ptr = &kxcj91008_info },
+ { .name = "kxtj21009", .driver_data_ptr = &kxtj21009_info },
+ { .name = "kxtf9", .driver_data_ptr = &kxtf9_info },
+ { .name = "kx023-1025", .driver_data_ptr = &kx0231025_info },
{ }
};
MODULE_DEVICE_TABLE(i2c, kxcjk1013_id);
that are an improvement for readability (again!) and it keeps some
properties of the pointers (here: being const) without having to pay
attention for that. (I didn't find a good example in sound/soc, so an
iio driver was used to demonstrate the gain.)
My additional motivation for this effort is CHERI[1]. This is a hardware
extension that uses 128 bit pointers but unsigned long is still 64 bit.
So with CHERI you cannot store pointers in unsigned long variables.
The first patch drops a few empty remove callbacks that I found while
working on patch #2. The second converts all hwmon drivers to use named
initializers.
Link: https://patch.msgid.link/cover.1778692164.git.u.kleine-koenig@baylibre.com
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
i2c_device_id that replaces .driver_data by an anonymous union.
While touching all these arrays, unify indention and usage of commas.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/ae2ff4898eb340bd8bcafb7b75443eb4a0ce3e76.1778692164.git.u.kleine-koenig@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Like the HP ProBook 440 G6, the HP ProBook 430 G6 needs
the ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk for its
mute and microphone mute LEDs.
Tested on a HP ProBook 430 G6.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Link: https://patch.msgid.link/20260519140248.4211-2-mail@mariushoch.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pending irq work might be still floating while the assigned stream
has been already closed, which may lead to UAF, especially when
another async work for fasync is involved.
For addressing this, extend the hda_controller_ops for allowing the
extra cleanup procedure that is specific to the controller driver, and
make sure to cancel and sync the pending irq work at each PCM close
before releasing the resources.
Reported-by: Jake Lamberson <lamberson.jake@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260519121157.28477-2-tiwai@suse.de
Currently, the delayed IRQ handling for PCM streams is managed in a
single work embedded in hda_intel, but this is basically a per-stream
thing. Due to the single work, we can't cancel the work properly at
closing each stream, for example.
For making the IRQ pending work to be stream-based, this patch changes
the following:
- An extended version of azx_dev (i.e. the hd-audio stream object) is
defined for snd-hda-intel
- The irq_pending flag and irq_pending_work are moved to
hda_intel_stream, so that they can be hda-intel stream specific
- The stream creation and assignment are refactored so that
snd-hda-intel can handle individually;
the snd-hda-intel specific workaround for stream tags is also moved
to snd-hda-intel itself instead of the common code
- The irq pending work is canceled properly at free / shutdown
While we're at it, changed the bit field flag to bool, as the bit
field doesn't help much in our case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260519121157.28477-1-tiwai@suse.de
Some CA0132 implementations (e.g. Gigabyte GA-Z170X-Gaming G1) produce
white noise when using the DSP firmware path. Add a QUIRK_GENERIC path
that uses the standard HDA generic parser instead, with custom pin
configs.
This patch applies against v6.18.24.
Signed-off-by: Ezio Galeazzi <eziogale@gmail.com>
Link: https://lore.kernel.org/0c0b781f-1595-4595-921a-66d83cf5930b@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Z66 G6 14 inch laptop uses the ALC236 codec with subsystem ID
0x103c:8df7. Without a quirk entry, the PCI SSID falls back to the
generic 0x103c:0000 fixup, which does not configure the mute/micmute
LED GPIOs correctly.
Add the SND_PCI_QUIRK entry for this model using
ALC236_FIXUP_HP_GPIO_LED, matching the surrounding HP EliteBook G12
entries (0x8dec-0x8dfe) which share the same ALC236 codec and GPIO LED
layout.
Signed-off-by: Minxi Hou <houminxi@gmail.com>
Link: https://patch.msgid.link/20260518031542.2899188-1-houminxi@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Pavilion Plus 14-eh0xxx with subsystem ID 103c:8a36 needs the
ALC245 COEF bit mute LED quirk for the mute LED to follow the audio mute
state.
Add the missing quirk entry.
Signed-off-by: Aryan Kushwaha <aryankushwaha3101@gmail.com>
Link: https://patch.msgid.link/20260516144436.35022-1-aryankushwaha3101@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Heiko reported that BIOS on some recent machines doesn't set up PCI
SSID properly but leave with zero (e.g. on HP Dragonfly Folio 13.5
inch G3 with SSID 103c:8a05/8a06), which confuses the quirk table
matching and results in the non-functional state.
Fix it by skipping the PCI SSID matching when either vendor or device
ID is zero and falling back to the codec SSID that is supposed to be
more stable for those cases.
Reported-by: Heiko Schmid <heiko@future-machines.org>
Tested-by: Heiko Schmid <heiko@future-machines.org>
Closes: https://lore.kernel.org/20260514133110.12302-1-heiko@future-machines.org
Link: https://patch.msgid.link/20260515105700.276420-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP 250 15.6 inch G10 Notebook PC uses the same ALC236 codec
as the HP 255 15.6 inch G10 (103c:8b2f) and requires the same
fixup to enable the internal speaker EAPD and microphone routing.
Signed-off-by: Sergio Boglione <sboglione@gmail.com>
Link: https://patch.msgid.link/20260516131651.143109-1-sboglione@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These devices were incorrectly using the ALC287_FIXUP_TAS2781_I2C quirk
leading to errors:
[ 18.765990] Serial bus multi instantiate pseudo device driver TXNW2781:00: error -ENXIO: IRQ index 0 not found
[ 18.768153] Serial bus multi instantiate pseudo device driver TXNW2781:00: error -ENXIO: IRQ index 0 not found
[ 18.768476] Serial bus multi instantiate pseudo device driver TXNW2781:00: error -ENXIO: IRQ index 0 not found
[ 18.768899] Serial bus multi instantiate pseudo device driver TXNW2781:00: Instantiated 3 I2C devices.
Use the ALC287_FIXUP_TXNW2781_I2C quirk instead to fix this and restore
speaker audio on affected devices.
Fixes: 1e9c708dc3 ("ALSA: hda/tas2781: Add new quirk for Lenovo, ASUS, Dell projects")
Link: https://lore.kernel.org/59fd4aa4-76b9-4984-8db9-a60e55ec6e80@losource.net/
Closes: https://lore.kernel.org/CACB9z7kjs8rhLstEc8fV29BCTb5dd881JwGozoKdO5cwCb=YwQ@mail.gmail.com
Signed-off-by: Eric Naim <dnaim@cachyos.org>
Link: https://patch.msgid.link/20260516111532.111463-1-dnaim@cachyos.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cs35l41_hda creates ALSA controls whose private data points at the
cs35l41_hda object. The firmware load control can also queue
fw_load_work.
Those controls are not removed on component unbind, and device remove
only cancels fw_load_work through cs35l41_remove_dsp(). That helper is
skipped when halo_initialized is false. With firmware_autostart
disabled, a firmware load can be requested before the DSP has been
initialized. If the component or device is removed before the queued
work runs, the worker can run after teardown and dereference driver
state that is no longer valid.
Track the created controls and remove them on unbind so no new control
callback can reach the driver data or queue more work. Then cancel
fw_load_work to drain any request that was already queued. Also cancel
the work unconditionally during device remove before runtime PM teardown.
Fixes: 47ceabd99a ("ALSA: hda: cs35l41: Support Firmware switching and reloading")
Fixes: 4c870513fb ("ALSA: hda: cs35l41: Add read-only ALSA control for forced mute")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Reviewed-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260511-alsa-hda-cs35l41-fw-work-teardown-v1-1-1184e9bc4f25@gmail.com
Commit 778031e165 ("ALSA: hda/ca0132: Set HP/Speaker
auto-detect default from headphone pin verb") enables HP/Speaker
auto-detect by default when the headphone pin supports presence detect.
With auto-detect enabled, ca0132_select_out() and ca0132_alt_select_out()
choose the output from jack presence instead of the manual HP/Speaker
selection. This means selecting speaker output while headphones are
plugged in updates the control state, but audio still routes to the
headphones.
Treat an explicit manual output selection as a request to leave
auto-detect mode. Clear the HP/Speaker auto-detect switch before applying
the manual selection, and notify userspace so the auto-detect control
state is updated in mixers. Do this for both the normal HP/Speaker
Playback Switch and the alternate Output Select control used by desktop
cards.
This keeps auto-detect enabled by default for devices with jack presence
detection, while preserving the expected behavior that a manual output
choice takes effect immediately.
Fixes: 778031e165 ("ALSA: hda/ca0132: Set HP/Speaker auto-detect default from headphone pin verb")
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Link: https://lore.kernel.org/CAFTm+6AfeXKf=b2frG4xC5yC4jjM9TkD6c8+dOWWFw6BDjDESw@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a SND_PCI_QUIRK entry for the HP Pavilion Laptop 16-ag0xxx
(subsystem 0x103c:0x8cbc, Realtek ALC245). The
ALC245_FIXUP_HP_X360_MUTE_LEDS fixup is already used by the
neighbouring HP Pavilion Aero Laptop 13-bg0xxx (0x103c:0x8cbd);
it chains the master-mute COEF handler with the GPIO mic-mute
LED handler, which is what this machine needs.
Tested on the affected hardware: both the mute and mic-mute key
LEDs respond correctly to the keyboard hotkeys after this change.
Cc: <stable@vger.kernel.org>
Signed-off-by: Adrien Burnett <an.arctic.pigeon@gmail.com>
Link: https://patch.msgid.link/20260514165905.21175-1-an.arctic.pigeon@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Volume control for the speakers on the Lenovo Yoga Pro 7 15ASH11 laptop
doesn't work.
The DAC routing is the same as on the ThinkPad X1 Gen7 function, so reuse
the alc285_fixup_thinkpad_x1_gen7 to get it working.
Signed-off-by: Jackie Dong <xy-jackie@139.com>
Link: https://patch.msgid.link/20260514153940.7320-1-xy-jackie@139.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_ctl_add() dereferences kctl->id.subdevice without checking
whether kctl is NULL. Multiple callers in sound/hda/codecs/ca0132.c
pass the return value of snd_ctl_new1() directly to snd_hda_ctl_add()
without a NULL check:
return snd_hda_ctl_add(codec, nid, snd_ctl_new1(&knew, codec));
snd_ctl_new1() returns NULL when the underlying snd_ctl_new() fails
on memory allocation (kzalloc_flex),which can occur under memory
pressure or via fault injection.
Add a NULL check at the entry of snd_hda_ctl_add(), matching the
pattern already used by snd_ctl_add_replace() at the same call
path (sound/core/control.c:515). Return -EINVAL to let callers
handle the error gracefully.
Fixes: 44f0c9782c ("ALSA: hda/ca0132: Add tuning controls")
Signed-off-by: Quan Sun <2022090917019@std.uestc.edu.cn>
Link: https://patch.msgid.link/20260514132245.3062884-1-2022090917019@std.uestc.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Samsung Galaxy Book5 360 (NP750QHA, PCI subsystem ID 0x144d:0xc902)
has severe audio distortion on the 3.5mm headphone jack. Applying
ALC256_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET corrects the output path
configuration, consistent with fixes already applied to other Samsung
Galaxy Book models using the same ALC256 codec.
Cc: stable@vger.kernel.org
Link: https://github.com/thesofproject/linux/issues/5648
Signed-off-by: Markus Kramer <linux@markus-kramer.de>
Link: https://patch.msgid.link/20260513222818.14351-1-linux@markus-kramer.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
First of all, it has to be 'default n' (small letter n), otherwise
it looks for CONFIG_N which is absent and in case of appearance
will enable something unrelated. Second and most important is that
'n' *is* the default 'default' already. Hence just drop malformed
line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260513162758.365972-1-andriy.shevchenko@linux.intel.com
In addition to the mic jack fix, also need to avoid boosting the
internal mic too much, otherwise >50% input volume clips a lot.
Also add a second SSID. We have one for the classic chassis/speaker and
one for the new Pro chassis/speaker.
To: Jaroslav Kysela <perex@perex.cz>
To: Takashi Iwai <tiwai@suse.com>
To: linux-sound@vger.kernel.org
Cc: Dustin L. Howett <dustin@howett.net>
Cc: linux@frame.work
Signed-off-by: Daniel Schaefer <dhs@frame.work>
Link: https://patch.msgid.link/20260513155513.11683-1-dhs@frame.work
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal mic boost on the Positivo DN50E is too high.
Fix this by applying the ALC269_FIXUP_LIMIT_INT_MIC_BOOST fixup to the machine
to limit the gain.
Signed-off-by: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>
Link: https://patch.msgid.link/20260511181558.670563-1-edson.drosdeck@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Acer Nitro AN515-58 uses GPIO 4 in active-low configuration to
control the mic-mute LED. This patch adds a fixup to register the LED
classdev and associate it with the mic-mute trigger, while chaining to
the existing headset mic fixup.
Signed-off-by: Dirga Yuza <dirgayuza123@gmail.com>
Link: https://patch.msgid.link/20260510055951.9035-1-dirgayuza123@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Legion 7 16ITHG6 uses codec SSID 17aa:3855, but its PCI
SSID is 17aa:3811. The latter is now also used by the Legion S7 15IMH05
quirk, which is matched before codec SSID fallback and incorrectly
routes Legion 7 16ITHG6 machines to ALC287_FIXUP_LEGION_15IMHG05_SPEAKERS.
That fixup does not bind the CLSA0101 CS35L41 companion amplifiers,
making the built-in speakers silent even though playback appears to be
active.
Add a codec SSID quirk for 17aa:3855 before the conflicting PCI SSID
quirk so that the Legion 7 16ITHG6 uses ALC287_FIXUP_LEGION_16ITHG6.
This restores CS35L41 firmware loading and binds both speaker
amplifiers.
Fixes: 67f4c61a73 ("ALSA: hda/realtek: Add quirk for Legion S7 15IMH")
Cc: stable@vger.kernel.org
Tested-by: Nicholas Bonello <hadobedo@gmail.com>
Assisted-by: Codex:GPT-5
Signed-off-by: Nicholas Bonello <hadobedo@gmail.com>
Link: https://patch.msgid.link/20260508225507.47667-1-hadobedo@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
acpi_dev_get_first_match_dev() returns a refcounted ACPI device and
callers must balance it with acpi_dev_put().
cs35l41_hda_read_acpi() stores the returned ACPI device in
cs35l41->dacpi. That reference is normally released by the later
probe cleanup or the remove path, but the NULL-check on
physdev exits before either of those paths can run.
Drop the lookup reference before returning -ENODEV.
Fixes: c34b04cc61 ("ALSA: hda: cs35l41: Fix NULL pointer dereference in cs35l41_hda_read_acpi()")
Signed-off-by: Shuhao Fu <sfual@cse.ust.hk>
Tested-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260428081238.GA1659932@chcpu16
acpi_dev_get_first_match_dev() returns a refcounted ACPI device and
callers are expected to balance it with acpi_dev_put().
When no companion is already attached, cs35l56_hda_read_acpi() looks
up an ACPI device and sets it with ACPI_COMPANION_SET(), but leaves
the lookup reference held.
ACPI_COMPANION_SET() does not take ownership of that reference, so
drop it with acpi_dev_put() after attaching the companion.
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Signed-off-by: Shuhao Fu <sfual@cse.ust.hk>
Tested-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260428080139.GA1649104@chcpu16
Some Lenovo Yoga Pro 9 16IMH9 units carry codec SSID 17aa:38d5 instead
of 17aa:38d6, which was added in commit 56722cfbb7 ("ALSA: hda/realtek:
Add codec SSID quirk for Lenovo Yoga Pro 9 16IMH9"). The corresponding
firmware blob TAS2XXX38D5.bin already ships in linux-firmware, and the
hardware is otherwise identical: same PCI subsystem ID 17aa:3811 shared
with the Legion S7 15IMH05, same TI TAS2781 amplifiers behind ACPI HID
TIAS2781, same ALC287_FIXUP_TAS2781_I2C requirement.
Add a second HDA_CODEC_QUIRK entry directly above the existing 17aa:38d6
entry so both variants resolve to the correct fixup. Reported and
verified on hardware by GitHub user 0xEthamin.
Link: https://github.com/ramonvanraaij/yoga9-tas2781-hda/issues/1
Signed-off-by: Rámon van Raaij <ramon@vanraaij.eu>
Link: https://patch.msgid.link/20260506183118.patch1-ramon@vanraaij.eu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TAS2781 HDA I2C and SPI queue RCA firmware loading from component
bind with request_firmware_nowait(). The firmware loader keeps the
callback module pinned and holds a device reference, but the callback
still uses driver-private HDA state.
Component unbind removes controls and DSP state immediately. Later
device removal tears down the TAS2781 private data, including
codec_lock. If the async firmware callback runs after unbind has
started, it can operate on state that is being torn down.
Cancel or synchronize the async firmware request before removing
controls and DSP state. A queued callback is cancelled, and an
already-running callback is allowed to finish before unbind continues.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Fixes: bb5f86ea50 ("ALSA: hda/tas2781: Add tas2781 hda SPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260505-alsa-hda-tas2781-fw-callback-teardown-v4-2-e7c4bf930dc8@gmail.com
Add a new fixup for the mute LED on the HP Pavilion 15-cs1xxx series
using the VREF on NID 0x1b.
The BIOS on these models (tested up to F.32) incorrectly reports
the mute LED on NID 0x18 via DMI OEM strings, which lacks VREF
capabilities. This fixup overrides the LED pin to the correct
NID 0x1b.
Signed-off-by: Rodrigo Faria <rodrigofilipefaria@gmail.com>
Link: https://patch.msgid.link/20260505185518.23625-1-rodrigofilipefaria@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This enables the mute and mic-mute LEDs on the HP Envy X360 15-fh0xxx
2-in-1 laptops.
The quirk 'ALC245_FIXUP_HP_ENVY_X360_15_FH0XXX' has been created and
is now enabled for this device.
This is my first patch, and I'm still getting to grips with the code,
so there's probably a better way to implement this fix.
I apologize for any inconvenience caused by the constant release of
new versions of this patch.
Signed-off-by: Fernando Antunez Antonio <fer.antunez24antonio@gmail.com>
Link: https://patch.msgid.link/20260504-hpenvy-muteled-fix-v3-1-5567fd9b3d25@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and PCI device helpers.
The various struct pci_device_id arrays were initialized mostly by list
expressions, some of them using the PCI_DEVICE macros. This isn't easily
readable if you're not into PCI. Using named initializers is more
explicit and thus easier to parse. Also use PCI_DEVICE* helper macros to
assign .vendor, .device, .subvendor and .subdevice where appropriate and
skip explicit assignments of 0 (which the compiler takes care of).
The secret plan is to make struct pci_device_id::driver_data an
anonymous union (similar to
https://lore.kernel.org/all/cover.1776579304.git.u.kleine-koenig@baylibre.com/)
and that requires named initializers. But it's also a nice cleanup on
its own.
This change doesn't introduce changes to the compiled pci_device_id
array. Tested on x86 and arm64.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260430135255.279393-2-u.kleine-koenig@baylibre.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Yoga Pro 9 16IMH9 (codec SSID 17aa:38d6) shares PCI audio device
subsystem ID 17aa:3811 with the Legion S7 15IMH05. The existing
SND_PCI_QUIRK entry for the Legion routes both machines to
ALC287_FIXUP_LEGION_15IMHG05_SPEAKERS, which does not bind the TAS2781
smart amplifiers, resulting in near-silent built-in speakers.
Add an HDA_CODEC_QUIRK entry immediately before the conflicting PCI quirk
that matches the Yoga Pro 9's unique codec SSID and routes it to
ALC287_FIXUP_TAS2781_I2C. Codec quirks are evaluated after PCI quirks and
take precedence, leaving the Legion S7 15IMH05 entry unaffected.
This follows the same pattern used to disambiguate PCI SSID 17aa:3847
(shared between Yoga Pro 7 14IMH9 and Legion 7 16ACHG6), where a
HDA_CODEC_QUIRK for codec SSID 17aa:38cf resolves the conflict.
Signed-off-by: Rámon van Raaij <ramon@vanraaij.eu>
Link: https://patch.msgid.link/20260430191224.patch1-ramon@vanraaij.eu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Xiaomi Mi Laptop Pro 15 (TM1905, subsystem 1d72:1905) ships with the
Realtek ALC256 codec on Intel Comet Lake PCH-LP. After S3 resume the
codec sets coefficient register 0x10 to 0x0220 instead of 0x0020 — bit 9
is erroneously set, which silences the internal speaker. Bluetooth and
HDMI audio are unaffected because they use different paths.
This is the same mechanism fixed for Clevo NJ51CU by commit edca7cc4b0
("ALSA: hda/realtek: Fix quirk for Clevo NJ51CU"), but the existing
ALC256_FIXUP_MIC_NO_PRESENCE_AND_RESUME also reconfigures pin 0x19 as a
front mic, which is wrong for this Xiaomi where pin 0x19 default is
0x411111f0 (disabled). Add a minimal fixup that only clears the stuck
coef bit, and add the Xiaomi SSID to the quirk table.
Verified by reading coef 0x10 with hda-verb after resume (returns
0x0220), writing 0x0020, and confirming the internal speaker resumes
output. With this fixup applied the bit is cleared on every codec init,
including post-resume.
Signed-off-by: Yuriy Padlyak <yuriypadlyak@gmail.com>
Cc: <stable@vger.kernel.org>
Tested-by: Yuriy Padlyak <yuriypadlyak@gmail.com>
Link: https://patch.msgid.link/20260429220903.14918-1-yuriypadlyak@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In TAS2781 SPI mode, when accessing non-book-zero or page numbers greater
than 1 in book 0, an additional byte must be read. The first byte in such
cases is a dummy byte and should be ignored.
Fixes: 9fa6a693ad ("ALSA: hda/tas2781: Remove tas2781_spi_fwlib.c and leverage SND_SOC_TAS2781_FMWLIB")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20260429054206.429-1-shenghao-ding@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eliminate the uninitialized 'nval' in cs35l56_hda_read_acpi() if a
system-specific quirk overrides processing of the dev-index property.
The value is now stored in a new 'num_amps' member of struct cs35l56_hda
so that the quirk handler can set the value.
The quirk for the Lenovo Yoga Book 9i GenX replaces the values from the
dev-index property with hardcoded indexes. So cs35l56_hda_read_acpi() would
then skip reading the property. But this left the 'nval' local variable
uninitialized when it is later passed to cirrus_scodec_get_speaker_id().
Fixes: 40b1c2f9b2 ("ALSA: hda/cs35l56: Workaround bad dev-index on Lenovo Yoga Book 9i GenX")
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/linux-sound/aenFesLAStjrVNy8@stanley.mountain/T/#u
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260428130531.169600-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In cx_probe(), the return value of snd_hda_jack_detect_enable_callback()
is ignored. This function returns a pointer, and if it fails (e.g., due
to memory allocation failure), it returns an error pointer which must
be checked using IS_ERR().
If the registration fails, the driver continues to probe, but the jack
detection callback will not be registered. This can lead to a kernel
crash later when the driver attempts to handle jack events or accesses
the uninitialized structure.
Check the return value using IS_ERR() and propagate the error via
PTR_ERR() to the probe caller.
Fixes: 7aeb259086 ("ALSA: hda/conexant: Fix headset auto detect fail in cx8070 and SN6140")
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20260428080450.108801-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At parsing the channel mapping for HDMI, the current code may spew
WARN_ON() unnecessarily for the case where only invalid (zero) channel
maps are given from the hardware. Drop WARN_ON() and reorganize the
code a bit for avoiding the hdmi_slot over the array size.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221390
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260428061800.80527-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kconfiglint reports:
M004: 'snd-hda-codec-cmedia-y' assigned with ':=' but was already
assigned at line 5; previous value is overwritten
sound/hda/codecs/Makefile contains duplicate entries for the C-Media
codec driver — both the composite module definition and the obj-* build
target appear twice:
Line 5: snd-hda-codec-cmedia-y := cmedia.o
Line 10: snd-hda-codec-cmedia-y := cmedia.o (duplicate)
Line 24: obj-$(CONFIG_SND_HDA_CODEC_CMEDIA) += snd-hda-codec-cmedia.o
Line 29: obj-$(CONFIG_SND_HDA_CODEC_CMEDIA) += snd-hda-codec-cmedia.o (duplicate)
This file was created by commit 6014e9021b ("ALSA: hda: Move codec
drivers into sound/hda/codecs directory") which
moved codec drivers from sound/pci/hda/ to sound/hda/codecs/. In that
initial file, cmedia appeared once in each section.
Immediately after, commit aeeb85f26c ("ALSA: hda: Split Realtek
HD-audio codec driver") reordered the entries and
inserted cmedia at new positions near the top of each section, as part
of splitting out the Realtek driver. However, the original cmedia entries
were not removed during this reordering, creating duplicates of both
lines. The second assignment harmlessly overwrites the first with the
same value, and the second obj-* line causes the module to be listed
twice — neither causes a build failure, but both are dead code.
Remove the duplicate entries (second occurrence of each).
Assisted-by: Claude:claude-opus-4-6 kconfiglint
Signed-off-by: Sasha Levin <sashal@kernel.org>
Link: https://patch.msgid.link/20260426000327.56079-1-sashal@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mic-mute LED on the Acer Aspire A315-44P (subsystem ID 0x10251640)
does not light up when the microphone is muted. The LED is connected to
GPIO3 of the Realtek ALC256 codec.
Add a quirk entry using ALC256_FIXUP_ACER_SFG16_MICMUTE_LED, which
configures GPIO3 (bitmask 0x04) as the micmute LED, identical to
the Acer Swift SFG16.
Tested by manually sending HDA verb commands directly to the codec
and verifying that GPIO3 drives the LED while GPIO1 and GPIO2
do not.
Signed-off-by: Naser Al-Asbahi <nasserqahtan0@gmail.com>
Link: https://patch.msgid.link/20260425154014.83982-1-nasserqahtan0@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On ThinkBook 16p systems the platform mute LED is present and
bound to the audio-mute trigger, but it does not react to Master
mute changes.
The affected fixup chain sets up the DAC routing, but does not enable
vmaster mute LED handling. Because of that, the generic HDA code does
not mark Master Playback Switch with SNDRV_CTL_ELEM_ACCESS_SPK_LED,
and the audio-mute trigger never receives speaker mute updates.
Add a ThinkBook-specific wrapper around alc287_fixup_bind_dacs() and
enable spec->gen.vmaster_mute_led during PRE_PROBE. This keeps the
existing DAC binding logic unchanged while allowing the normal generic
LED path to drive the mute LED.
Signed-off-by: Yuxuan Qiu <yuxuanqiu596@gmail.com>
Link: https://patch.msgid.link/20260424112107.22206-1-yuxuanqiu596@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cs35l56_hda_mixer_get() ignores regmap_read() and
cs35l56_hda_mixer_put() ignores regmap_update_bits_check().
This makes the ASP TX source controls report success when a regmap
access fails. The write path returns no change instead of an error,
and the read path continues after a failed read instead of aborting
the control callback.
Propagate the regmap errors, matching the posture and volume controls
in this driver.
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260423-alsa-cs35l56-asp-tx-source-errors-v1-1-17ea7c62ec31@gmail.com
The mute LED on this laptop uses ALC245 but requires a quirk to work.
This patch enables the existing ALC245_FIXUP_HP_MUTE_LED_COEFBIT
quirk for the device.
Tested my Victus 15-fa2xxx (PCI SSID 103c:8dcd).
The LED behaviour works as intended.
Cc: stable@vger.kernel.org
Signed-off-by: Spencer Payton <spayton681@gmail.com>
Link: https://patch.msgid.link/20260421084918.14685-1-spayton681@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the SPI driver probe, the chip ID must be set to TAS2781. Without this
initialization, calibration data fails to load correctly, causing audio
abnormalities on some devices.
And update the register bulk read API to handle the distinct requirements
of SPI and I2C devices.
Fixes: 05ac3846ff ("ALSA: hda/tas2781: A workaround solution to lower-vol issue among lower calibrated-impedance micro-speaker on TAS2781")
Signed-off-by: Baojun Xu <baojun.xu@ti.com>
Link: https://patch.msgid.link/20260418055030.765-1-baojun.xu@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hda-intel driver uses request_firmware_nowait() for loading its
patch, and tries to continue the probe directly from the fw loader
callback. This works in principle, but it has a few drawbacks:
- The driver may be released before the firmware callback completes
- Having two ways of async probe makes the code flow unnecessarily
complex
The former issue is more severe, as it may potentially lead to a UAF,
and there is no explicit way to cancel the pending firmware worker
for now.
This patch changes the firmware loading to be performed rather in the
common probe work without *_nowait(). Then the pending work can be
easily canceled, and the code becomes more straightforward.
A nice bonus is that, by moving into the probe work, the firmware
doesn't need any longer to be cached, hence we can get rid of struct
azx.fw field, and release the firmware immediately after parsing it,
too.
Fixes: 5cb543dba9 ("ALSA: hda - Deferred probing with request_firmware_nowait()")
Link: https://patch.msgid.link/20260415135526.1813126-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Acer PT316-51S (PCI SSID 1025:160e) with ALC287 codec does not
detect the headset microphone due to missing BIOS pin configuration
for pin 0x19. Apply ALC2XX_FIXUP_HEADSET_MIC to enable it.
Signed-off-by: Faye Nichols <faye.opensource@gmail.com>
Link: https://patch.msgid.link/20260413212645.117119-1-faye.opensource@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's one new core feature here but mostly this has been a fairly
quiet release, we've got a few new drivers and one core feature that's
likely to be relatively rarely used but the bulk of the work this time
around has been on quality.
- Support for bus keepers, this will be used by the Apple device
support.
- Enhancements to the SDCA support, incuding retaskable jacks.
- Unwinding of the pcm_new()/pcm_free() cleanups from Morimoto-san.
- Test improvements for the Cirrus Logic drivers.
- Large sets of fixes for the NXP, nVidia and Qualcomm drivers.
- Support for AMD RPL DMICs, Cirrus Logic CS42L43 and CS47L47, nVidia
machines with CPCAP and WM8962.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmnc1/sACgkQJNaLcl1U
h9D/vgf+MuGaIT9hIyPaFMETvQUmvcJ3c1evGa7sQKAy7cdQPkk/rkjYDkQcVSL7
N8LVJPlN5CXmIxhMJbsIpcNijtOqBdX/hK1QV5EtY9TNrJIxaCNULIsP00FedceO
cliFxs2JIHrvldxPGTxxtB+kU5a3/bVae/ofh+hOOvJWGxG3W3FE1AZ+8kN29eS6
aAe20+prmhW3/TjDRlHE9vFk67MfGUtS6FKHEScCCMqMCukImIjcuZlrp6i3NwFn
mQX2xWgUf/0yE19efzhzYq3mRS1YzyZrIBLUylITbufBekPSWJWjD2ndyULNwotb
1qOJ2lgEWSPMs0SlroxN6dGSTI4VTA==
=3UsT
-----END PGP SIGNATURE-----
Merge tag 'asoc-v7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v7.1
There's one new core feature here but mostly this has been a fairly
quiet release, we've got a few new drivers and one core feature that's
likely to be relatively rarely used but the bulk of the work this time
around has been on quality.
- Support for bus keepers, this will be used by the Apple device
support.
- Enhancements to the SDCA support, incuding retaskable jacks.
- Unwinding of the pcm_new()/pcm_free() cleanups from Morimoto-san.
- Test improvements for the Cirrus Logic drivers.
- Large sets of fixes for the NXP, nVidia and Qualcomm drivers.
- Support for AMD RPL DMICs, Cirrus Logic CS42L43 and CS47L47, nVidia
machines with CPCAP and WM8962.
HP Spectre x360 Convertible 14-ea0xxx (2021 model or so)
doesn't make produce sound,The Bang & Olufsen speaker amplifier
is not enabled.
Root causing:
The PCI subsystem ID is 103c:0000 (HP left it unset), while the codec
subsystem ID is 103c:885b. The vendor-wide catch-all
SND_PCI_QUIRK_VENDOR(0x103c, "HP", ALC269_FIXUP_HP_MUTE_LED) matches
103c:0000 before the codec SSID fallback is reached, so
ALC245_FIXUP_HP_X360_AMP never applies.
So add the quirk in alc269_fixup_tbl.
Reported-by: dzidmail <dzidmail@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221341
Signed-off-by: songxiebing <songxiebing@kylinos.cn>
Link: https://patch.msgid.link/20260413011854.96520-1-songxiebing@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
alc269_resume() has an extra code to write GPIO data, but this is
basically already done in the standard alc_init(), hence it's
superfluous. Let's drop the code.
Since all external callers of alc_write_gpio_data() are gone after
this, fold the only usage of alc_write_gpio_data() into the caller and
drop the export as well.
Link: https://patch.msgid.link/20260409143735.1412134-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far we used the verb cache to restore the GPIO mask, direction and
data bits at PM resume. But, due to the nature of the cache resume
mechanism, the calling order isn't guaranteed, and this might lead to
some inconsistency at the restored state.
For assuring the GPIO verb orders, use the new GPIO helper function to
explicitly set up the GPIO bits, instead of using the codec verb
caches, while keeping the current data bits in ad198x_spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-6-tiwai@suse.de
The previous implementation of the quirk for CSL Unity BF24B in commit
de65275fc9 ("ALSA: hda/realtek: Add quirk for CSL Unity BF24B")
introduced the unnecessary GPIO caching which leads to a superfluous
write at each init/resume.
Use the new helper to write GPIO bits directly for optimization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-5-tiwai@suse.de
Use a new helper function to clean up the code.
Along with it, make alc_write_gpio() static as well, which is used
only locally in realtek.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-4-tiwai@suse.de
We used snd_hda_codec_read() for the verb write when a synchronization
is needed after the write, e.g. for the power state toggle or such
cases. It works in principle, but it looks rather confusing and too
hackish.
For improving the code readability, introduce a new helper function,
snd_hda_codec_write_sync(), which is another variant of
snd_hda_codec_write(), and replace the existing snd_hda_codec_read()
calls with this one.
No behavior change but just the code refactoring.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-2-tiwai@suse.de
Intel ACE4 based products set more strict constraints on HDA BDLE start
address and length alignment. Modify capability flags to drop
AZX_DCAPS_NO_ALIGN_BUFSIZE for Intel Nova Lake platforms.
Fixes: 7f428282fd ("ALSA: hda: controllers: intel: add support for Nova Lake")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260408084514.24325-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bass speakers are not working, and add the following entry
in /etc/modprobe.d/snd.conf:
options snd-sof-intel-hda-generic hda_model=alc287-yoga9-bass-spk-pin
Fixes the bass speakers.
So add the quick ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN here.
Reported-by: Fernando Garcia Corona <fgarcor@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221317
Signed-off-by: songxiebing <songxiebing@kylinos.cn>
Link: https://patch.msgid.link/20260405012651.133838-1-songxiebing@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "IEC958 Default PCM Playback Switch" control is backed directly by
mout->share_spdif. The share-switch callbacks currently access that state
without serialization, and spdif_share_sw_put() always returns 0, so
normal userspace writes never emit the standard ALSA control value
notification.
snd_hda_multi_out_analog_open() may also clear mout->share_spdif when the
analog PCM capabilities and the SPDIF capabilities no longer intersect.
That fallback is still needed to avoid creating an impossible hw
constraint set, but it changes the mixer backing value without notifying
subscribers.
Protect the share-switch callbacks with spdif_mutex like the other SPDIF
control handlers, return the actual change value from spdif_share_sw_put(),
and notify the cached control when the open path forcibly disables
shared SPDIF mode after dropping spdif_mutex.
This keeps the existing auto-disable behavior while making switch state
changes visible to userspace.
Fixes: 9a08160bdb ("[ALSA] hda-codec - Add "IEC958 Default PCM" switch")
Fixes: 022b466fc3 ("ALSA: hda - Avoid invalid formats and rates with shared SPDIF")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260403-hda-spdif-share-notify-v3-1-4eb1356b0f17@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Yoga Pro 7 14IMH9 (DMI: 83E2) shares PCI SSID 17aa:3847
with the Legion 7 16ACHG6, but has a different codec subsystem ID
(17aa:38cf). The existing SND_PCI_QUIRK for 17aa:3847 applies
ALC287_FIXUP_LEGION_16ACHG6, which attempts to initialize an external
I2C amplifier (CLSA0100) that is not present on the Yoga Pro 7 14IMH9.
As a result, pin 0x17 (bass speakers) is connected to DAC 0x06 which
has no volume control, making hardware volume adjustment completely
non-functional. Audio is either silent or at maximum volume regardless
of the slider position.
Add a HDA_CODEC_QUIRK entry using the codec subsystem ID (17aa:38cf)
to correctly identify the Yoga Pro 7 14IMH9 and apply
ALC287_FIXUP_YOGA9_14IMH9_BASS_SPK_PIN, which redirects pin 0x17 to
DAC 0x02 and restores proper volume control. The existing Legion entry
is preserved unchanged.
This follows the same pattern used for 17aa:386e, where Legion Y9000X
and Yoga Pro 7 14ARP8 share a PCI SSID but are distinguished via
HDA_CODEC_QUIRK.
Link: https://github.com/nomad4tech/lenovo-yoga-pro-7-linux
Tested-by: Alexander Savenko <alex.sav4387@gmail.com>
Signed-off-by: Alexander Savenko <alex.sav4387@gmail.com>
Link: https://patch.msgid.link/20260331082929.44890-1-alex.sav4387@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mention complains about this coding style:
ERROR: code indent should use tabs where possible
#6640: FILE: sound/hda/codecs/realtek/alc269.c:6640:
+ [ALC233_FIXUP_LENOVO_GPIO2_MIC_HOTKEY] = {$
fix it up.
Fixes: 5de5db3535 ("ALSA: hda/realtek - Enable Mute LED for Lenovo platform")
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Link: https://patch.msgid.link/20260331024036.30782-1-huanglei814@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Pin Complex 0x17 (bass/woofer speakers) is incorrectly reported as
unconnected in the BIOS (pin default 0x411111f0 = N/A). This causes the
kernel to configure speaker_outs=0, meaning only the tweeters (pin 0x14)
are used. The result is very low, tinny audio with no bass.
The existing quirk ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN (already present
in patch_realtek.c for SSID 0x17aa3801) fixes the issue completely.
Reported-by: Garcicasti <andresgarciacastilla@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221298
Signed-off-by: songxiebing <songxiebing@kylinos.cn>
Link: https://patch.msgid.link/20260331033650.285601-1-songxiebing@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for laptops:
- ASUS PM5406CGA
- ASUS PM5606CGA
- ASUS P5406CCA
- ASUS P5606CCA
Laptops use 2 CS35L41 Amps with HDA, using Internal boost, with I2C or
SPI.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://patch.msgid.link/20260330134651.443439-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Dragonfly 13.5 inch G4 (SSID 103C8B63) has _DSD properties in
ACPI firmware with valid reset-gpios and cs-gpios for the four CS35L41
amplifiers on SPI.
However, the _DSD specifies cirrus,boost-type as Internal (0), while
the hardware requires External Boost. With Internal Boost configured,
the amplifiers trigger "Amp short error" when audio is played at
moderate-to-high volume, eventually shutting down entirely.
Add a configuration table entry to override the boost type to
External, similar to the existing workaround for 103C89C6. All GPIO
indices are set to -1 since the _DSD provides valid reset-gpios and
cs-gpios.
Confirmed on BIOS V90 01.11.00 (January 2026), the latest available.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219520
Originally-by: Nicholas Wang <me@nicho1as.wang>
Signed-off-by: Leonard Lausen <leonard@lausen.nl>
Link: https://patch.msgid.link/db84dcf91bc8dbd217b35572b177d967655ff903@lausen.nl
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is another Book2 Pro model (NP950QED) that seems equipped with
the same speaker module as the non-360 model, which requires
ALC298_FIXUP_SAMSUNG_AMP_V2_2_AMPS quirk.
Reported-by: Throw <zakkabj@gmail.com>
Link: https://patch.msgid.link/20260330162249.147665-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The error message in cs8409_i2c_bulk_read() incorrectly says "I2C Bulk
Write Failed" when it should say "I2C Bulk Read Failed". This is a
copy-paste error from cs8409_i2c_bulk_write().
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20260330054131.434994-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit ab949d5196 ("ALSA: hda - Fix deadlock of controller device
lock at unbinding") added a temporary device_unlock()/device_lock()
pair around probe-work cancellation to avoid a deadlock between
controller unbind and codec probe.
That deadlock depended on the driver core taking both a device lock and
its parent lock during bind and unbind. Since commit 8c97a46af0
("driver core: hold dev's parent lock when needed") and follow-up
fixes, the parent lock is only taken when bus->need_parent_lock is set.
The HDA bus does not set that flag, so codec binding no longer locks
the controller device as the codec's parent.
Keep cancel_delayed_work_sync(), since the async probe/remove race
still needs to be serialized, but drop the stale unlock/relock
workaround and its outdated FIXME comment. Keeping it around only
opens an unnecessary unlocked window inside azx_remove().
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260328-hda-intel-drop-obsolete-probe-workaround-v1-1-bc43aeafc98b@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
print_gpio() prints the GPIO capability header and the bidirectional
GPIO state, but it never reports the separate GPI and GPO pins even
though AC_PAR_GPIO_CAP exposes their counts.
The HD-audio specification defines dedicated GPI and GPO verbs
alongside the GPIO ones, so codecs with input-only or output-only
general-purpose pins currently lose that state from
/proc/asound/card*/codec#* altogether.
Add the missing read verb definitions and extend print_gpio() to dump
the GPI and GPO pins, too, while leaving the existing IO[] output
unchanged.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260328-hda-proc-gpi-gpo-v1-1-fabb36564bee@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a mute led quirck for HP Victus 15-fb0xxx (103c:8a3d) model
- As it used 0x8(full bright)/0x7f(little dim) for mute led on and other
values as 0ff (0x0, 0x4, ...)
- So, use ALC245_FIXUP_HP_MUTE_LED_V2_COEFBIT insted for safer approach
Cc: <stable@vger.kernel.org>
Signed-off-by: Sourav Nayak <nonameblank007@gmail.com>
Link: https://patch.msgid.link/20260327142805.17139-1-nonameblank007@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This motherboard uses USB audio instead, causing this driver to complain
about "no codecs found!".
Add it to the denylist to silence the warning.
The first attempt only matched on the PCI device, but this caused issues
for some laptops, so DMI match against the board as well.
Signed-off-by: Stuart Hayhurst <stuart.a.hayhurst@gmail.com>
Link: https://patch.msgid.link/20260327155737.21818-2-stuart.a.hayhurst@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar to commit 7b509910b3 ("ALSA hda/realtek: Add quirk for
Framework F111:000C") and previous quirks for Framework systems with
Realtek codecs.
000F is another new platform with an ALC285 which needs the same quirk.
Signed-off-by: Dustin L. Howett <dustin@howett.net>
Link: https://patch.msgid.link/20260327-framework-alsa-000f-v1-1-74013aba1c00@howett.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 30b3211aa2 ("ALSA: hda/intel: Add MSI X870E Tomahawk
to denylist") was added to silence a warning, but this effectively
reintroduced commit df42ee7e22 ("ALSA: hda: Add ASRock
X670E Taichi to denylist") which was already reported to cause
problems and reverted in commit ee8f161359 ("Revert "ALSA: hda:
Add ASRock X670E Taichi to denylist"")
Revert it yet again.
Cc: stable@vger.kernel.org
Reported-by: Juhyun Song <juju6985@outlook.kr>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221274
Cc: Stuart Hayhurst <stuart.a.hayhurst@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20260326190542.524515-1-mario.limonciello@amd.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Laptop 15-fd0xxx with ALC236 codec does not handle the toggling of
the mute LED.
This patch adds a quirk entry for subsystem ID 0x8dd7 using
ALC236_FIXUP_HP_MUTE_LED_COEFBIT2 fixup, enabling correct mute LED
behavior.
Signed-off-by: Kshamendra Kumar Mishra <kshamendrakumarmishra@gmail.com>
Link: https://patch.msgid.link/DHAB51ISUM96.2K9SZIABIDEQ0@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Pavilion 15-eg0xxx with subsystem ID 0x103c87cb uses a Realtek
ALC287 codec with a mute LED wired to GPIO pin 4 (mask 0x10). The
existing ALC287_FIXUP_HP_GPIO_LED fixup already handles this correctly,
but the subsystem ID was missing from the quirk table.
GPIO pin confirmed via manual hda-verb testing:
hda-verb SET_GPIO_MASK 0x10
hda-verb SET_GPIO_DIRECTION 0x10
hda-verb SET_GPIO_DATA 0x10
Signed-off-by: César Montoya <sprit152009@gmail.com>
Link: https://patch.msgid.link/20260321153603.12771-1-sprit152009@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the HP EliteBoard G1a platform (models without a headphone jack).
the speaker mute LED failed to function. The Sysfs ctl-led info showed
empty values because the standard LED registration couldn't correctly
bind to the master switch.
Adding this patch will fix and enable the speaker mute LED feature.
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/279e929e884849df84687dbd67f20037@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The machine is equipped with ALC294 and requires the
ALC287_FIXUP_TXNW2781_I2C_ASUS quirk for the amplifier to work properly.
Since the machine's PCI SSID is also 1043:1204, HDA_CODEC_QUIRK is
used to retain the previous quirk.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221173
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Link: https://patch.msgid.link/20260316022843.2809968-1-zhangheng@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The initial StarFighter quirk fixed the runtime suspend pop by muting
speakers in the shutup callback before power-down. Further hardware
validation showed that the speaker path is controlled directly by LINE2
EAPD on NID 0x1b together with GPIO2 for the external amplifier.
Replace the shutup-delay workaround with explicit sequencing of those
controls at playback start and stop:
- assert LINE2 EAPD and drive GPIO2 high on PREPARE
- deassert LINE2 EAPD and drive GPIO2 low on CLEANUP
This avoids the runtime suspend pop without a sleep, and also fixes pops
around G3 entry and display-manager start that the original workaround
did not cover.
Fixes: 1cb3c20688 ("ALSA: hda/realtek: Fix speaker pop on Star Labs StarFighter")
Tested-by: Sean Rhodes <sean@starlabs.systems>
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Link: https://patch.msgid.link/20260315201127.33744-1-sean@starlabs.systems
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes lack of audio output on the ASUS ROG Flow Z13-KJP GZ302EAC model,
similar to the ASUS ROG Flow Z13 GZ302EA.
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Link: https://patch.msgid.link/20260313172503.285846-1-matthew.schwartz@linux.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Sen Wang <sen@ti.com>:
Just two minor patches that aim to tidy up the code a little bit,
as well as fix the aux_div selection in davinci_mcasp_calc_clk_div()
for mid-range dividers (33 <= div <= 4096).
Sen Wang (2):
ASoC: ti: davinci-mcasp: extract mcasp_is_auxclk_enabled() helper
ASoC: ti: davinci-mcasp: improve aux_div selection for mid-range dividers
sound/soc/ti/davinci-mcasp.c | 45 +++++++++++++++++++++++++-----------
1 file changed, 31 insertions(+), 14 deletions(-)
--
2.43.0
This patch addresses a potential state inconsistency bug and optimizes
runtime performance:
1. Fix error handling in set_beep_amp():
Previously, beep_nid was assigned before adding kcontrols. If
kcontrol creation failed, the function returned error but left
beep_nid set, causing inconsistent driver state. Moved the
assignment to the end of the function.
2. Optimize senary_auto_turn_eapd():
Removed the redundant snd_hda_query_pin_caps() check inside the
loop. The target pins are sourced from spec->eapds, which is
strictly filtered during the initial parse phase. Checking
capabilities again during every mute/unmute hook is unnecessary
overhead.
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20260310023649.155858-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo ThinkPad X390 (ALC257 codec, subsystem ID 0x17aa2288)
does not report headset button press events. Headphone insertion is
detected (SW_HEADPHONE_INSERT), but pressing the inline microphone
button on a headset produces no input events.
Add a SND_PCI_QUIRK entry that maps this subsystem ID to
ALC285_FIXUP_THINKPAD_NO_BASS_SPK_HEADSET_JACK, which enables
headset jack button detection through alc_fixup_headset_jack()
and ThinkPad ACPI integration. This is the same fixup used by
similar ThinkPad models (P1 Gen 3, X1 Extreme Gen 3).
Signed-off-by: Uzair Mughal <contact@uzair.is-a.dev>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260307012906.20093-1-contact@uzair.is-a.dev
HP Laptop 14s-dr5xxx with ALC236 codec does not handle the toggling of
the mute LED.
This patch adds a quirk entry for subsystem ID 0x8a1f using
ALC236_FIXUP_HP_MUTE_LED_COEFBIT2 fixup, enabling correct mute LED
behavior.
Signed-off-by: Liucheng Lu <luliucheng100@outlook.com>
Link: https://patch.msgid.link/PAVPR03MB9774F3FCE9CCD181C585281AE37BA@PAVPR03MB9774.eurprd03.prod.outlook.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Port the essential hardware initialization logic from the vendor driver
and introduce the standard HDA fixup framework to handle different
machine configurations.
Key changes:
1. Add hardware init verbs:
- Implement `senary_init_verb` to send the vendor-specific
initialization sequence required by the SN6186 chip.
- Override pin capabilities for Node 0x19 to ensure proper headset
microphone support.
2. Introduce fixup framework:
- Define a default pin configuration table (`senary_pincfg_default`)
to provide a fallback for devices with invalid BIOS configurations.
- Establish a quirk table structure for future machine-specific
fixes.
- Since the standard quirk matching relies on Subsystem IDs, we
manually apply the default fixup if `snd_hda_pick_fixup` does not
find a specific match.
This ensures the chip is correctly initialized during probe and resume,
and provides a scalable mechanism for supporting specific hardware
quirks.
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20260304070219.450083-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver sets spec->gen.own_eapd_ctl to take manual control of the
EAPD (External Amplifier). However, senary_init does not turn on the
EAPD, while senary_shutdown turns it off.
Since the generic driver skips EAPD handling when own_eapd_ctl is set,
the EAPD remains off after initialization (e.g., after resume), leaving
the codec in a non-functional state.
Explicitly call senary_auto_turn_eapd in senary_init to ensure the EAPD
is enabled and the codec is functional.
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20260303081516.583438-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the hardcoded GPIO node ID (0x01) with codec->core.afg.
This follows the standard HDA driver practice and makes the driver
more robust against different hardware configurations.
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20260303054242.318062-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
Currently, we set a predefined codec component name in a DAI link. But
the codec name may contain an index which is not fixed. This series
suggest using partial match the codec name to fix the issue.
On TAS2781, if the Speaker calibrated impedance is lower than default
value hard-coded inside the TAS2781, it will cuase vol lower than
normal. In order to fix this issue, the parameter of SineGainI need
updating.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Tested-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Link: https://patch.msgid.link/20260227144641.1243-1-shenghao-ding@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP/Speaker auto-detect (VNID_HP_ASEL) has been off by default for every
CA0132 device since the driver was added in 2012. vnode_lswitch is
always initialized to 0 in ca0132_init_chip(), and no quirk or other
code path enables it. As a result, headphone jack detection works only
after the user manually turns on "HP/Speaker Auto Detect" in alsamixer,
which is not obvious on laptops with combo jacks (e.g. Google Link,
Alienware).
Change the default to follow the headphone pin config: if the pin verb
has presence detect enabled (no AC_DEFCFG_MISC_NO_PRESENCE) and the
codec supports it (AC_PINCAP_PRES_DETECT), enable HP_ASEL by default.
This lets firmware (coreboot, UEFI, etc.) express whether the headphone
jack supports insertion detection. Devices with combo jacks can default
to auto-detect; devices with fixed/no jack leave it off.
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Link: https://patch.msgid.link/20260226163055.825167-1-matt.devillier@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit af37511305 ("firmware: cs_dsp: Don't require client to
provide a struct cs_dsp_client_ops") the client doesn't have to provide
a struct cs_dsp_client_ops. So remove the dummy cs_dsp_client_ops.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260226124115.1811187-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In cs35l56_hda_posture_put() assign ucontrol->value.integer.value[0] to
a long instead of an unsigned long. ucontrol->value.integer.value[0] is
a long.
This fixes the sparse warning:
sound/hda/codecs/side-codecs/cs35l56_hda.c:256:20: warning: unsigned value
that used to be signed checked against zero?
sound/hda/codecs/side-codecs/cs35l56_hda.c:252:29: signed value source
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://patch.msgid.link/20260226111728.1700431-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default bdl_pos_adj of 32 for Nvidia HDA controllers is
insufficient on GA102 (and likely other recent Nvidia GPUs) after S3
suspend/resume. The controller's DMA timing degrades after resume,
causing premature IRQ detection in azx_position_ok() which results in
silent HDMI/DP audio output despite userspace reporting a valid
playback state and correct ELD data.
Increase bdl_pos_adj to 64 for AZX_DRIVER_NVIDIA, matching the value
already used by Intel Apollo Lake for the same class of timing issue.
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221069
Suggested-by: Charalampos Mitrodimas <charmitro@posteo.net>
Signed-off-by: Panagiotis Foliadis <pfoliadis@posteo.net>
Link: https://patch.msgid.link/20260225-nvidia-audio-fix-v1-1-b1383c37ec49@posteo.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar to other Samsung laptops, NT950QCT also requires the
ALC298_FIXUP_SAMSUNG_AMP quirk applied.
Cc: <stable@vger.kernel.org>
Signed-off-by: Juhyung Park <qkrwngud825@gmail.com>
Link: https://patch.msgid.link/20260222122609.281191-2-qkrwngud825@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Acer Aspire V3-572G has a combo jack (ALC283) but the BIOS
sets pin 0x19 to 0x411111f0 (not connected), so the headset mic
is not detected.
Add a quirk to override pin 0x19 as a headset mic and enable
headset mode.
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221075
Suggested-by: Charalampos Mitrodimas <charmitro@posteo.net>
Signed-off-by: Panagiotis Foliadis <pfoliadis@posteo.net>
Reviewed-by: Charalampos Mitrodimas <charmitro@posteo.net>
Link: https://patch.msgid.link/20260221-fix-detect-mic-v1-1-b6e427b5275d@posteo.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Star Labs StarFighter (Realtek ALC233/235), the internal speakers can
emit an audible pop when entering or leaving runtime suspend.
Mute the speaker output paths via snd_hda_gen_shutup_speakers() in the
Realtek shutup callback before the codec is powered down.
This is enough to avoid the pop without special EAPD handling.
Test results:
- runtime PM pop fixed
- still reaches D3 (PCI 0000:00:1f.3 power_state=D3hot)
- does not address pops on cold boot (G3 exit) or around display manager
start/shutdown
journalctl -k (boot):
- snd_hda_codec_alc269 hdaudioC0D0: ALC233: picked fixup for PCI SSID
7017:2014
- snd_hda_codec_alc269 hdaudioC0D0: autoconfig for ALC233: line_outs=1
(0x1b/0x0/0x0/0x0/0x0) type:speaker
Suggested-by: Takashi Iwai <tiwai@suse.com>
Tested-by: Sean Rhodes <sean@starlabs.systems>
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Link: https://patch.msgid.link/4d5fb71b132bb283fd41c622b8413770b2065242.1771532060.git.sean@starlabs.systems
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add appropriate SPDX-License-Identifier lines to the
the remaining files that are missing such lines in the
sound/soc directory, and in a few other miscelaneous files.
Remove boilerplate license text.
Signed-off-by: Tim Bird <tim.bird@sony.com>
Link: https://patch.msgid.link/20260217190837.165504-1-tim.bird@sony.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
here are a bunch of updates, but there should be no big surprises;
mostly device-specific quirks and fix-ups or non-code changes.
- Quirks for ASoC AMD, HD-audio and USB-audio
- Fixes in ASoC fsl, rockchip, renesas, aw codecs
- Fixes for USB-audio packet handling in the implicit feedback mode
- Updates of SPDX license IDs in some files
-----BEGIN PGP SIGNATURE-----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=01P5
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a bunch of updates, but there should be no big surprises;
mostly device-specific quirks and fix-ups or non-code changes:
- Quirks for ASoC AMD, HD-audio and USB-audio
- Fixes in ASoC fsl, rockchip, renesas, aw codecs
- Fixes for USB-audio packet handling in the implicit feedback mode
- Updates of SPDX license IDs in some files"
* tag 'sound-fix-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (28 commits)
ASoC: rockchip: i2s-tdm: Use param rate if not provided by set_sysclk
ALSA: hda/hdmi: Add quirk for TUXEDO IBS14G6
ASoC: dt-bindings: asahi-kasei,ak5558: Fix the supply names
ASoC: dt-bindings: asahi-kasei,ak4458: Fix the supply names
ASoC: dt-bindings: asahi-kasei,ak4458: set unevaluatedProperties:false
ASoC: amd: amd_sdw: add machine driver quirk for Lenovo models
ASoC: amd: acp: Add ACP7.0 match entries for Realtek parts
ALSA: echoaudio: Add SPDX ids to some files
ALSA: isa: Add SPDX id lines to some files
ALSA: core: Add SPDX license id to files
ASoC: tas2783A: add explicit port prepare handling
ASoC: renesas: rz-ssi: Fix playback and capture
ALSA: hda/realtek: Fix headset mic on ASUS Zenbook 14 UX3405MA
ALSA: hda/conexant: Fix headphone jack handling on Acer Swift SF314
ASoC: qcom: sm8250: Add quinary MI2S support
ASoC: amd: yc: Add DMI quirk for ASUS Vivobook Pro 15X M6501RR
ALSA: usb-audio: Avoid potentially repeated XRUN error messages
ALSA: usb-audio: Add sanity check for OOB writes at silencing
ALSA: usb-audio: Optimize the copy of packet sizes for implicit fb handling
ALSA: usb-audio: Update the number of packets properly at receiving
...
Depending on the timing during boot, the BIOS might report wrong pin
capabilities, which can lead to HDMI audio being disabled. Therefore,
force HDMI audio connection on TUXEDO InfinityBook S 14 Gen6.
Signed-off-by: Aaron Erhardt <aer@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://patch.msgid.link/20260218213234.429686-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add SPDX-License-Identifier lines to several files where
they are missing, mostly in the sound/isa subdir.
Use GPL-2.0 as the id.
[ note: the same change applied to sound/hda/core/trace.c, too -- tiwai ]
Signed-off-by: Tim Bird <tim.bird@sony.com>
Link: https://patch.msgid.link/20260212195905.3726149-1-tim.bird@sony.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS Zenbook 14 UX3405MA uses an ALC294 codec with CS35L41
amplifiers over SPI. The existing quirk for this model only configured
the amplifiers, leaving the headset microphone on the combo jack
non-functional.
Introduce a new fixup that configures pin 0x19 as headset mic input
and chains to ALC245_FIXUP_CS35L41_SPI_2 to preserve speaker
functionality.
Similar to the fix done for the UM3406HA in commit 018f659753
("ALSA: hda/realtek: Fix headset mic on ASUS Zenbook 14").
Signed-off-by: Erik Sanjaya <sirreidlos@gmail.com>
Link: https://patch.msgid.link/20260217102112.20651-1-sirreidlos@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's been relatively calm for a new era; majority of changes are for
ASoC, mostly device-specific changes, while there are a bit of
cleanups in core stuff. A few SPI API and regmap updates are included
to be used by sound drivers, too.
Core:
- A few trivial cleanups about __free() and runtime PM macros
- Convert to new snd_seq_bus binding
ASoC:
- Generic SDCA support for reporting jack events
- Continuing platform support, cleanup and feature improvements for
AMD, Intel, Qualcomm and SOF code
- Platform description improvements for the Cirrus drivers
- Support for NXP i.MX952, Realtek RT1320 and RT5575, and Sophogo
CV1800B
HD- and USB-audio:
- Many quirks as usual
-----BEGIN PGP SIGNATURE-----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=kfLN
-----END PGP SIGNATURE-----
Merge tag 'sound-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been relatively calm for a new era; majority of changes are for
ASoC, mostly device-specific changes, while there are a bit of
cleanups in core stuff. A few SPI API and regmap updates are included
to be used by sound drivers, too.
Core:
- A few trivial cleanups about __free() and runtime PM macros
- Convert to new snd_seq_bus binding
ASoC:
- Generic SDCA support for reporting jack events
- Continuing platform support, cleanup and feature improvements for
AMD, Intel, Qualcomm and SOF code
- Platform description improvements for the Cirrus drivers
- Support for NXP i.MX952, Realtek RT1320 and RT5575, and Sophogo
CV1800B
HD- and USB-audio:
- Many quirks as usual"
* tag 'sound-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: usb-audio: Add DSD support for iBasso DC04U
ALSA: mixer: oss: Add card disconnect checkpoints
ASoC: SOF: ipc4-control: Set correct error code in refresh_bytes_control
ASoC: SOF: Intel: select CONFIG_SND_HDA_EXT_CORE from SND_SOC_SOF_HDA_COMMON
ALSA: usb-audio: Add iface reset and delay quirk for AB13X USB Audio
ASoC: amd: maintainer information
ALSA: ctxfi: Add quirk for SE-300PCIE variant (160b:0102)
ALSA: hda/generic: fix typos in comments
ALSA: hda/realtek - Enable mute LEDs on HP ENVY x360 15-es0xxx
ALSA: hda/conexant: Add quirk for HP ZBook Studio G4
ASoC: fsl_asrc_dma: allocate memory from dma device
ASoC: fsl_asrc: Add support for i.MX952 platform
ASoC: fsl_asrc_m2m: Add option to start ASRC before DMA device for M2M
ASoC: dt-bindings: fsl,imx-asrc: Add support for i.MX952 platform
ALSA: oss: delete self assignment
ASoC: rockchip: spdif: Convert to FIELD_PREP
ASoC: rockchip: spdif: Fill IEC958 CS info per params
ASoC: rockchip: spdif: Add support for format S32_LE
ASoC: rockchip: spdif: Add support for set mclk rate
ASoC: rockchip: spdif: Swap PCM and DAI component registration order
...
In the SPI driver probe, the device should be in the default state, so the
device status check is not necessary. It should be forced to do the
firmware download as I2C device.
Signed-off-by: Baojun Xu <baojun.xu@ti.com>
Link: https://patch.msgid.link/20260211030946.2330-1-baojun.xu@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Samsung Galaxy Book3 Pro 360 NP965QFG (subsystem ID 0x144d:0xc1cb)
uses the same Realtek ALC298 codec and amplifier configuration as the
NP960QFG (0x144d:0xc1ca). Apply the same ALC298_FIXUP_SAMSUNG_AMP_V2_4_AMPS
fixup to enable the internal speakers.
Cc: stable@vger.kernel.org
Signed-off-by: Lewis Mason <lewis@ocuru.co.uk>
Link: https://patch.msgid.link/20260210231337.7265-1-lewis@ocuru.co.uk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Add interrupt redirection infrastructure
Some PCI controllers use a single demultiplexing interrupt for the MSI
interrupts of subordinate devices.
This prevents setting the interrupt affinity of device interrupts, which
causes device interrupts to be delivered to a single CPU. That obviously is
counterproductive for multi-queue devices and interrupt balancing.
To work around this limitation the new infrastructure installs a dummy
irq_set_affinity() callback which captures the affinity mask and picks a
redirection target CPU out of the mask.
When the PCI controller demultiplexes the interrupts it invokes a new
handling function in the core, which either runs the interrupt handler in
the context of the target CPU or delegates it to irq_work on the target CPU.
- Utilize the interrupt redirection mechanism in the PCI DWC host controller
driver.
This allows affinity control for the subordinate device MSI interrupts
instead of being randomly executed on the CPU which runs the demultiplex
handler.
- Replace the binary 64-bit MSI flag with a DMA mask
Some PCI devices have PCI_MSI_FLAGS_64BIT in the MSI capability, but
implement less than 64 address bits. This breaks on platforms where such a
device is assigned an MSI address higher than what's supported.
With the binary 64-bit flag there is no other choice than disabling 64-bit
MSI support which leaves the device disfunctional.
By using a DMA mask the address limit of a device can be described
correctly which provides support for the above scenario.
- Make use of the DMA mask based address limit in the hda/intel and radeon
drivers to enable them on affected platforms.
- The usual small cleanups and improvements
-----BEGIN PGP SIGNATURE-----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=SCSQ
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2026-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI updates from Thomas Gleixner:
"Updates for the [PCI] MSI subsystem:
- Add interrupt redirection infrastructure
Some PCI controllers use a single demultiplexing interrupt for the
MSI interrupts of subordinate devices.
This prevents setting the interrupt affinity of device interrupts,
which causes device interrupts to be delivered to a single CPU.
That obviously is counterproductive for multi-queue devices and
interrupt balancing.
To work around this limitation the new infrastructure installs a
dummy irq_set_affinity() callback which captures the affinity mask
and picks a redirection target CPU out of the mask.
When the PCI controller demultiplexes the interrupts it invokes a
new handling function in the core, which either runs the interrupt
handler in the context of the target CPU or delegates it to
irq_work on the target CPU.
- Utilize the interrupt redirection mechanism in the PCI DWC host
controller driver.
This allows affinity control for the subordinate device MSI
interrupts instead of being randomly executed on the CPU which runs
the demultiplex handler.
- Replace the binary 64-bit MSI flag with a DMA mask
Some PCI devices have PCI_MSI_FLAGS_64BIT in the MSI capability,
but implement less than 64 address bits. This breaks on platforms
where such a device is assigned an MSI address higher than what's
supported.
With the binary 64-bit flag there is no other choice than disabling
64-bit MSI support which leaves the device disfunctional.
By using a DMA mask the address limit of a device can be described
correctly which provides support for the above scenario.
- Make use of the DMA mask based address limit in the hda/intel and
radeon drivers to enable them on affected platforms
- The usual small cleanups and improvements"
* tag 'irq-msi-2026-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ALSA: hda/intel: Make MSI address limit based on the device DMA limit
drm/radeon: Make MSI address limit based on the device DMA limit
PCI/MSI: Check the device specific address mask in msi_verify_entries()
PCI/MSI: Convert the boolean no_64bit_msi flag to a DMA address mask
genirq/redirect: Prevent writing MSI message on affinity change
PCI/MSI: Unmap MSI-X region on error
genirq: Update effective affinity for redirected interrupts
PCI: dwc: Enable MSI affinity support
PCI: dwc: Code cleanup
genirq: Add interrupt redirection infrastructure
genirq/msi: Correct kernel-doc in <linux/msi.h>
This release is almost all abut driers, there's very little core work
here, although some of that driver work is in more generic areas like
SDCA and SOF:
- Generic SDCA support for reporting jack events.
- Continuing platform support, cleanup and feature improements for the
AMD, Intel, Qualcomm and SOF code.
- Platform description improvements for the Cirrus drivers.
- Support for NXP i.MX952, Realtek RT1320 and RT5575, and Sophogo
CV1800B.
We also pulled in one small SPI API update and some more substantial
regmap work (cache description improvements) for use in drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmmKCo0ACgkQJNaLcl1U
h9AU7Af/Tu4SmEmMFW58Rn6DYPzX6P/eRvRW1wiazt+b3pyO8qPjRxhvpsBtSbVz
/TyhaO90QnBM7+31p6Hes4nHyC5HcOXXRNb/drt26kQmRpJPMH6NErm7Js6LXDyY
Yk/hzfyqG+DOFFlVoh9vnVE4jr1c4Oasqp8+FCzWbx8l1Y4ZgMEj2T7eQdfiowME
ILjislHqjoPPK4ZPCsGtbmVVYhT4+FMJLZaUDsaCLNRyWxVt1vutrWyvI6w6sA7d
9MUIECfE7MtLy1TaZRT2x0we+eWIjV1ji/7LalKmGvLPCSwTSbRh7A25RqZgL1lf
4/g08iQxIG37yEAmImxxqJnjsfS0yg==
=iwVH
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.20' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v7.0
This release is almost all abut driers, there's very little core work
here, although some of that driver work is in more generic areas like
SDCA and SOF:
- Generic SDCA support for reporting jack events.
- Continuing platform support, cleanup and feature improements for the
AMD, Intel, Qualcomm and SOF code.
- Platform description improvements for the Cirrus drivers.
- Support for NXP i.MX952, Realtek RT1320 and RT5575, and Sophogo
CV1800B.
We also pulled in one small SPI API update and some more substantial
regmap work (cache description improvements) for use in drivers.
The mute and mic-mute LEDs on HP ENVY x360 Convertible 15-es0xxx
(PCI SSID 103c:88b3) do not work with the current driver.
This model requires a combination of COEFBIT and GPIO fixups to
correctly control the LEDs. Introduce a new fixup function
alc245_fixup_hp_envy_x360_mute_led and add a quirk to apply it.
Signed-off-by: Illia Barbashyn <04baril@gmail.com>
Link: https://patch.msgid.link/20260207221955.24132-1-04baril@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TAS2781 driver supports three solutions of calibrated data. The first is
from the driver itself: driver reads the calibrated files directly during
probe; The second is from user space: during init of audio hal, the audio
hal will pass the calibrated data via kcontrol interface. Driver will
store this data in "struct calidata" for use. The third is from UEFI,
mainly used in hda device. These three solutions save the calibrated data
into different data structures. It is time to put them together into
"struct calidata" for use.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20260202102757.532-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
First, adding a generic quirk for Bass speaker DAC avoidance.
This pattern (re-routing the bass speakers off of a DAC without volume
control) seems common enough that having a "model" to match against and
quickly use to verify may be worthwhile.
The alc285_fixup_thinkpad_x1_gen7 routing was selected, amongst the
different options, as it should allow tuning the ratio between both
speaker set.
The routing was verified using `hda-verb`, and picking either 0x00 or
0x01. Either routing made the volume of the bass speakers controllable.
hda-verb /dev/snd/hwC1D0 0x17 SET_CONNECT_SEL 0x01
This likely will apply for the Minisforum V3, though there isn't a lot
of information to confirm whether or not the identifiers are the same.
This was verified on the Minisforum V3 SE, and the root cause (the bass
speakers routing) was found out by using pink noise, and playing with
the mixers.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Link: https://patch.msgid.link/20260203010132.1981419-2-samuel@dionne-riel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Chris Morgan <macroalpha82@gmail.com>:
Add support for the Anbernic RG-DS Speaker Amplifiers. The Anbernic
RG-DS uses two AW87391 ICs at 0x58 and 0x5B on i2c2. However, the
manufacturer did not provide a firmware file, only a sequence of
register writes to each device to enable and disable them.
Add support for this *specific* configuration in the AW87390 driver.
Since we are relying on a device specific sequence I am using a
device specific compatible string. This driver does not currently
support the aw87391 for any other device as I have none to test
with valid firmware. Attempts to create firmware with the AwinicSCPv4
have not been successful.
The hda/intel driver restricts the MSI message address for devices which do
not advertise full 64-bit DMA address space support to 32-bit due to the
former restrictions of the PCI/MSI code which only allowed either 32-bit or
a full 64-bit address range.
This does not work on platforms which have a MSI doorbell address above the
32-bit boundary but do not support the full 64 bit address range.
The PCI/MSI core converted this binary decision to a DMA_BIT_MASK() based
decision, which allows to describe the device limitations precisely.
Convert the driver to provide the exact DMA address limitations to the
PCI/MSI core. That allows devices which do not support the full 64-bit
address space to work on platforms which have a MSI doorbell address above
the 32-bit limit as long as it is within the hardware's addressable range.
[ tglx: Massage changelog ]
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260129-pci-msi-addr-mask-v4-4-70da998f2750@iscas.ac.cn
Some PCI devices have PCI_MSI_FLAGS_64BIT in the MSI capability, but
implement less than 64 address bits. This breaks on platforms where such
a device is assigned an MSI address higher than what's supported.
Currently, no_64bit_msi bit is set for these devices, meaning that only
32-bit MSI addresses are allowed for them. However, on some platforms the
MSI doorbell address is above the 32-bit limit but within the addressable
range of the device.
As a first step to enable MSI on those combinations of devices and
platforms, convert the boolean no_64bit_msi flag to a DMA mask and fixup
the affected usage sites:
- no_64bit_msi = 1 -> msi_addr_mask = DMA_BIT_MASK(32)
- no_64bit_msi = 0 -> msi_addr_mask = DMA_BIT_MASK(64)
- if (no_64bit_msi) -> if (msi_addr_mask < DMA_BIT_MASK(64))
Since no values other than DMA_BIT_MASK(32) and DMA_BIT_MASK(64) are used,
this is functionally equivalent.
This prepares for changing the binary decision between 32 and 64 bit to a
DMA mask based decision which allows to support systems which have a DMA
address space less than 64bit but a MSI doorbell address above the 32-bit
limit.
[ tglx: Massaged changelog ]
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com> # ionic
Reviewed-by: Thomas Gleixner <tglx@kernel.org>
Acked-by: Takashi Iwai <tiwai@suse.de> # sound
Link: https://patch.msgid.link/20260129-pci-msi-addr-mask-v4-1-70da998f2750@iscas.ac.cn
Merge series from "Peng Fan (OSS)" <peng.fan@oss.nxp.com>:
The main goal is to convert drivers to use GPIO descriptors. While reading
the code, I think it is time to remove ak4641 and pxa2xx-ac97 driver,
more info could be found in commit log of each patch.
Then only need to convert sound/arm/pxa2xx-ac97-lib.c to use GPIO
descriptors. Not have hardware to test the pxa2xx ac97.
The headset microphone on the MECHREVO Wujie 15X Pro requires the
CXT_FIXUP_HEADSET_MIC quirk to function properly. Add the PCI SSID
(0x1d05:0x3012) to the quirk table.
Signed-off-by: gongqi <550230171hxy@gmail.com>
Link: https://patch.msgid.link/20260122155501.376199-5-550230171hxy@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default of tas2781_hda::catlog_id is DELL, which cause calibration
data is not loaded in HP SPI-basded Laptop, because only HP laptop
supports SPI-based TAS2781.
Fixes: 9fa6a693ad ("ALSA: hda/tas2781: Remove tas2781_spi_fwlib.c and leverage SND_SOC_TAS2781_FMWLIB")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20260126031816.1123-1-shenghao-ding@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The LG Gram Style 14 (14Z90RS-G.AD77F, SSID 1854:0490) with Realtek ALC298
shows normal routing and volume changes, but internal speakers stay silent
unless a userland HDA-verb workaround is applied.
Add a dedicated quirk for the LG Gram Style 14 that programs the codec
coefficient sequence used by the known workaround and enables the speaker
amps only during playback.
Tested-by: Damien Dagorn <damien.dagorn29@gmail.com>
Signed-off-by: Damien Dagorn <damien.dagorn29@gmail.com>
Link: https://lore.kernel.org/CAN59QMUhd4kHrkRoJA6VzEr2VKezN2yjHnANaQoZn2-Bnwe3bQ@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a PCI quirk to enable microphone detection on the headphone jack of
TongFang X6AR55xU devices.
The former quirk entry did not acomplish this and is removed.
Fixes: b48fe9af1e ("ALSA: hda/realtek: Fix headset mic for TongFang X6AR55xU")
Signed-off-by: Tim Guttzeit <t.guttzeit@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://patch.msgid.link/20260123221233.28273-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Niether TASDEVICE_CALIBRATION_REG_ADDRESS nor TASDEV_UEFI_CALI_REG_ADDR_FLG
is referenced in the code, drop both.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20260123010000.1841-1-shenghao-ding@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If it play a 5s above silence media stream, it will cause silence
detection trigger.
Speaker will make no sound when you use another app to play a stream.
Add this patch will solve this issue.
GPIO2: Mute Hotkey GPIO3: Mic Mute LED
Enable this will turn on hotkey and LED support.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/f4929e137a7949238cc043d861a4d9f8@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp/speakers on the Lenovo Yoga Book 9i 13IRU8 laptop aren't
fully powered up, resulting in horrible tinny sound by default.
The kernel has an existing quirk for PCI SSID 0x17aa3843 which
matches this machine and several others. The quirk applies the
ALC287_FIXUP_IDEAPAD_BASS_SPK_AMP fixup, however the fixup does not
work on this machine.
This patch modifies the existing quirk by adding a check for the
subsystem ID 0x17aa3881. If present, ALC287_FIXUP_TAS2781_I2C will
be applied instead of ALC287_FIXUP_IDEAPAD_BASS_SPK_AMP. With this
change the TAS2781 amp is powered up, firmware is downloaded and
recognised by HDA/SOF - i.e. all is good, and we can boogie.
Code is re-used from alc298_fixup_lenovo_c940_duet7(), which fixes a
similar problem with two other Lenovo laptops.
Cross checked against ALSA cardinfo database for potential clashes.
Tested against 6.18.5 kernel built with Arch Linux default options.
Tested in HDA mode and SOF mode.
Note: Possible further work required to address quality of life issues
caused by the firmware's agressive power saving, and to improve ALSA
control mappings.
Signed-off-by: Martin Hamilton <m@martinh.net>
Link: https://patch.msgid.link/20260122-alc269-yogabook9i-fixup-v1-1-a6883429400f@martinh.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add entry for NVL variant of Nova Lake family.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260120193507.14019-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a PCI quirk to enable microphone detection on the headphone jack of
TongFang X6AR55xU devices.
Signed-off-by: Tim Guttzeit <t.guttzeit@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://patch.msgid.link/20260119151626.35481-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Sascha Hauer <s.hauer@pengutronix.de>:
These are some patches for the tlv320adcx140 codec we are carrying
around for a while, time to upstream them.
Change the test suite name string to "snd-hda-cirrus-scodec-test".
It was incorrectly named "snd-hda-scodec-cs35l56-test", a leftover
from when the code under test was actually in the cs35l56 driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test")
Link: https://patch.msgid.link/20260113134056.619051-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set gpiochip parent to the struct device of the dummy GPIO driver
so that the software node will be associated with the GPIO chip.
The recent commit e5d527be7e ("gpio: swnode: don't use the
swnode's name as the key for GPIO lookup") broke cirrus_scodec_test,
because the software node no longer gets associated with the GPIO
driver by name.
Instead, setting struct gpio_chip.parent to the owning struct device
will find the node using a normal fwnode lookup.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test")
Link: https://patch.msgid.link/20260113130954.574670-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Victus 16-e0xxx with ALC245 codec does not handle the toggling of
the mute LED.
This patch adds a quirk entry for subsystem ID 0x88eb using a new
ALC245_FIXUP_HP_MUTE_LED_V2_COEFBIT fixup, enabling correct mute LED
behavior.
Signed-off-by: Bharat Dev Burman <bharat.singh7924@gmail.com>
Link: https://patch.msgid.link/20260112184253.33376-1-bharat.singh7924@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds quirkiness for the Cirrus Logic CDB35L56-FOUR-HD board.
The quirk must be forced by model name "CDB35L56-FOUR-HD"
because there isn't a unique SSID that can be used. For example
in /etc/modprobe.d:
options snd-hda-intel model="CDB35L56-FOUR-HD"
The CDB35L56-FOUR-HD is not a complete PC. It is an add-on audio
board that requires a host system and replaces the normal HDA codec
on the host. Because of this there isn't an SSID that uniquely
identifies this configuration. Also, the usual host board is an
Aaeon UpXtreme, which doesn't have a unique SSID.
Because of this, the quirk must be forced by a module param.
This is acceptable because it is a development board, not an
end-user system, so there is no need for it to be detected
automatically.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Co-developed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260112142850.243054-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like GA403U, this GA403W needs to remap woofers to DAC1. Similarly to
other Asus devices, headphones/headset MIC is not working, however the pin
config alone is not enough to fix it.
From Windows dump of GA403W:
0x12, 0x90a60140 # Correctly set by codec out of the box
0x13, 0x90a60550
0x14, 0x90170510
0x17, 0x90170120 # Correctly set by codec out of the box
0x19, 0x03a11050 # Set by ALC285_FIXUP_ASUS_GA403U_HEADSET_MIC
0x1a, 0x411115F0
0x1b, 0x03a11c30 # Set by ALC285_FIXUP_ASUS_GA403U_HEADSET_MIC
0x1d, 0x40663A45 # Correctly set by codec out of the box
0x21, 0x03211430
Even with all the values set, MIC of the jack is not detected. Until a
complete solution is found, set ALC285_FIXUP_ASUS_GA403U_HEADSET_MIC
for GA403W which fixes audio volume control for woofers. No need to
create new quirk with missing pin config just yet, since its not
making the situation better.
Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
Link: https://patch.msgid.link/20260112-asus-rog-audio-v1-1-513957b4704e@vinarskis.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the correct function names and add a function parameter description
to avoid kernel-doc warnings:
hda_jack.h:97: warning: Function parameter or struct member 'cb' not
described in 'snd_hda_jack_detect_enable_callback'
hda_jack.h:97: warning: expecting prototype for snd_hda_jack_detect_enable().
Prototype was for snd_hda_jack_detect_enable_callback() instead
hda_local.h:441: warning: expecting prototype for _snd_hda_set_pin_ctl().
Prototype was for snd_hda_set_pin_ctl() instead
Fixes: cdd03cedc5 ("ALSA: hda - Introduce snd_hda_set_pin_ctl*() helper functions")
Fixes: 5204a05d70 ("ALSA: hda - Add DP-MST jack support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260106185951.2179242-1-rdunlap@infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Cristian Ciocaltea <cristian.ciocaltea@collabora.com>:
This series provides several fixes and cleanup patches for the Nuvoton
NAU88L21 audio codec driver.
Testing and validation has been performed on Valve Steam Deck.
HP Laptop 15s-eq1xxx with ALC236 codec does not enable the
mute LED automatically. This patch adds a quirk entry for
subsystem ID 0x8706 using the ALC236_FIXUP_HP_MUTE_LED_COEFBIT2
fixup, enabling correct mute LED behavior.
Signed-off-by: Ruslan Krupitsa <krupitsarus@outlook.com>
Link: https://patch.msgid.link/AS8P194MB112895B8EC2D87D53A876085BBBAA@AS8P194MB1128.EURP194.PROD.OUTLOOK.COM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add headset mic quirk for Acer Nitro AN517-55. This laptop uses
the same audio configuration as the AN515-58 model.
Signed-off-by: Matouš Lánský <matouslansky@post.cz>
Link: https://patch.msgid.link/20251231171207.76943-1-matouslansky@post.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use guard(pm_runtime_active) for replacing the manual calls of
pm_runtime_get_sync() and pm_runtime_put().
Merely code cleanups and no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251216141154.172218-5-tiwai@suse.de
Use guard(pm_runtime_active_auto) for replacing the manual calls of
pm_runtime_get_sync() and pm_runtime_put_autosuspend().
Along with this, we can use guard() for the tas_priv->codec_lock mutex
in tasdev_fw_ready(), too (that aligns both i2c and spi codes).
Merely code cleanups and no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251216141154.172218-4-tiwai@suse.de
Use PM_RUNTIME_ACQUIRE*() macros for replacing the manual
pm_runtime_resume_and_get() and pm_runtime_put_*() calls.
Merely code cleanups and no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251216141154.172218-3-tiwai@suse.de
Replace the manual pm_runtime_get_sync() and
pm_runtime_put_autosuspend() calls with the new
guard(pm_runtime_active_auto) for code simplification.
Along with this change, the former scoped_guard(mutex) can be set back
to the plain guard(mutex), and the indent level is taken back, too.
Merely code cleanups, and no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251216141154.172218-2-tiwai@suse.de
After speaker id retrieval was refactored to happen in tas2781_read_acpi,
devices that do not use a speaker id need a negative speaker_id value
instead of NULL, but no initialization was added to the TAS2563 code path.
This causes the driver to attempt to load a non-existent firmware file name
with a speaker id of 0 ("TAS2XXX38700.bin") instead of the correct file
name without a speaker id ("TAS2XXX3870.bin"), resulting in low volume and
these dmesg errors:
tas2781-hda i2c-INT8866:00: Direct firmware load for TAS2XXX38700.bin failed with error -2
tas2781-hda i2c-INT8866:00: tasdevice_dsp_parser: load TAS2XXX38700.bin error
tas2781-hda i2c-INT8866:00: dspfw load TAS2XXX38700.bin error
[...]
tas2781-hda i2c-INT8866:00: tasdevice_prmg_load: Firmware is NULL
Fix this by setting speaker_id to -1 as is done for other models.
Fixes: 945865a0dd ("ALSA: hda/tas2781: fix speaker id retrieval for multiple probes")
Cc: stable@vger.kernel.org
Signed-off-by: August Wikerfors <git@augustwikerfors.se>
Link: https://patch.msgid.link/20251222194704.87232-1-git@augustwikerfors.se
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The GENE_TWL7 project is an AAEON platform with a fixed audio
configuration consisting of line-out, line-in, and mic-in.
The audio routing and pin assignments are defined according to
the board-level hardware design and are not intended to be
dynamically changed.
Signed-off-by: Leo Tsai <antivirus621@gmail.com>
Link: https://patch.msgid.link/20251218055136.3875-1-antivirus621@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI subsystem ID of the HP machine Abe A6U should be 0x8ee7
instead of 0x8eb7.
Fixes: a30fa81222 ("ALSA: hda/realtek: fix mute/micmute LEDs don't work for more HP laptops")
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Link: https://patch.msgid.link/20251218062251.2039592-1-chris.chiu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By default, these devices use the quirk ALC294_FIXUP_ASUS_SPK. Not
using it causes the headphone jack to stop working. Therefore,
introduce a new quirk ALC287_FIXUP_TXNW2781_I2C_ASUS that binds
to the TAS amplifier while using that quirk.
Cc: stable@kernel.org
Fixes: 18a4895370 ("ALSA: hda/realtek: Add match for ASUS Xbox Ally projects")
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251216211714.1116898-1-lkml@antheas.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We used to have a variable declaration with __free() initialized with
NULL. This was to keep the old coding style rule, but recently it's
relaxed and rather recommends to follow the new rule to declare in
place of use for __free() -- which avoids potential deadlocks or UAFs
with nested cleanups.
Although the current code has no bug, per se, let's follow the new
standard and move the declaration to the place of assignment (or
directly assign the allocated result) instead of NULL initializations.
Fixes: ee0b0f5d32 ("ALSA: hda/generic: Use auto cleanup for temporary buffers")
Fixes: 03c5c350e3 ("ALSA: hda/realtek: Add support for new HP G12 laptops")
Fixes: b0550d4c2d ("ALSA: hda/common: Use auto cleanup for temporary buffers")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251216140634.171890-10-tiwai@suse.de
Quirk ALC236_FIXUP_HP_MUTE_LED_MICMUTE_GPIO make mute/micmute LEDs
on HP Abe and Bantie functional. But the micmute LED's function
is reversed, LED will be on when Mic enabled and off when Mic
disabled. Create a new function to fix the micmute LED reversed
issue.
Fixes: b72a6ddf6a ("ALSA: hda/realtek: fix mute/micmute LEDs don't work for HP 200 G2i")
Signed-off-by: Dirk Su <dirk.su@canonical.com>
Link: https://patch.msgid.link/20251217025257.44600-1-dirk.su@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While the used GML is consistent with the pattern for other Intel * Lake
SoCs, the de facto use is GLK. Update the acronym and users accordingly.
Note, a handful of the drivers for Gemini Lake in the Linux kernel use
GLK already (LPC, MEI, pin control, SDHCI, ...) and even some in ASoC.
The only ones in this patch used the inconsistent one.
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci_ids.h
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20251212181742.3944789-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When building without CONFIG_PM_SLEEP, there are several warnings (or
errors with CONFIG_WERROR=y / W=e) from the cix-ipbloq driver:
sound/hda/controllers/cix-ipbloq.c:378:12: error: 'cix_ipbloq_hda_runtime_resume' defined but not used [-Werror=unused-function]
378 | static int cix_ipbloq_hda_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/hda/controllers/cix-ipbloq.c:362:12: error: 'cix_ipbloq_hda_runtime_suspend' defined but not used [-Werror=unused-function]
362 | static int cix_ipbloq_hda_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/hda/controllers/cix-ipbloq.c:349:12: error: 'cix_ipbloq_hda_resume' defined but not used [-Werror=unused-function]
349 | static int cix_ipbloq_hda_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~
sound/hda/controllers/cix-ipbloq.c:336:12: error: 'cix_ipbloq_hda_suspend' defined but not used [-Werror=unused-function]
336 | static int cix_ipbloq_hda_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~
When CONFIG_PM and CONFIG_PM_SLEEP are unset, SET_SYSTEM_SLEEP_PM_OPS()
and SET_RUNTIME_PM_OPS() evaluate to nothing, so these functions appear
unused to the compiler in this configuration.
Use the modern SYSTEM_SLEEP_PM_OPS and RUNTIME_PM_OPS macros to resolve
these warnings, which is what they are intended to do. Additionally,
wrap &cix_ipbloq_hda_pm in pm_ptr() to ensure the compiler can drop the
entire structure when CONFIG_PM is unset.
Fixes: d91e9bd101 ("ALSA: hda: add CIX IPBLOQ HDA controller support")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20251211-hda-cix-ipbloq-modern-pm-ops-v1-1-c7a5580af021@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When config table entries don't match with the device to be probed,
currently we fall back to SND_INTEL_DSP_DRIVER_ANY, which means to
allow any drivers to bind with it.
This was set so with the assumption (or hope) that all controller
drivers should cover the devices generally, but in practice, this
caused a problem as reported recently. Namely, when a specific
kconfig for SOF isn't set for the modern Intel chips like Alderlake,
a wrong driver (AVS) got probed and failed. This is because we have
entries like:
#if IS_ENABLED(CONFIG_SND_SOC_SOF_ALDERLAKE)
/* Alder Lake / Raptor Lake */
{
.flags = FLAG_SOF | FLAG_SOF_ONLY_IF_DMIC_OR_SOUNDWIRE,
.device = PCI_DEVICE_ID_INTEL_HDA_ADL_S,
},
....
#endif
so this entry is effective only when CONFIG_SND_SOC_SOF_ALDERLAKE is
set. If not set, there is no matching entry, hence it returns
SND_INTEL_DSP_DRIVER_ANY as fallback. OTOH, if the kconfig is set, it
explicitly falls back to SND_INTEL_DSP_DRIVER_LEGACY when no DMIC or
SoundWire is found -- that was the working scenario. That being said,
the current setup may be broken for modern Intel chips that are
supposed to work with either SOF or legacy driver when the
corresponding kconfig were missing.
For addressing the problem above, this patch changes the fallback
driver to the legacy driver, i.e. return SND_INTEL_DSP_DRIVER_LEGACY
type as much as possible. When CONFIG_SND_HDA_INTEL is also disabled,
the fallback is set to SND_INTEL_DSP_DRIVER_ANY type, just to be sure.
Reported-by: Askar Safin <safinaskar@gmail.com>
Closes: https://lore.kernel.org/all/20251014034156.4480-1-safinaskar@gmail.com/
Tested-by: Askar Safin <safinaskar@gmail.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251210131553.184404-1-tiwai@suse.de
Add CIX IPBLOQ HDA controller support, which is integrated into
CIX SKY1 audio subsystem. HDA controller supports 64bit, but the
audio subsystem can only 32bit transaction. Use jack polling mode
as there is a hardware issue, lead to interrupt strom if the RIRB
interrupt enabled. Host and hdac has different view of memory, so
need do dma address translation.
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251205154621.3019640-4-joakim.zhang@cixtech.com
Add bus addr_offset field for dma address translation,
for some SoCs such as CIX SKY1 which is ARM64 Arch, HOST
and HDAC has different memory view, so need to do dma address
translation between HOST and HDAC.
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251205154621.3019640-3-joakim.zhang@cixtech.com
The acpi_get_first_physical_node() function can return NULL, in which
case the get_device() function also returns NULL, but this value is
then dereferenced without checking,so add a check to prevent a crash.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7b2f3eb492 ("ALSA: hda: cs35l41: Add support for CS35L41 in HDA systems")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251202101338.11437-1-arefev@swemel.ru
According to HW probes, there exist upgraded variants of HP ProBook
440/450 G8 notebook PC hardware, with PCI SSIDs not yet covered:
- https://linux-hardware.org/?id=pci:8086-a0c8-103c-8a76
(HP ProBook 440 G8, SSID 103C:8A76, Tiger Lake HDA, ALC236)
- https://linux-hardware.org/?id=pci:8086-a0c8-103c-8a77
(HP ProBook 450 G8, SSID 103C:8A77, Tiger Lake HDA, ALC236)
The HDA GPIO indices for the mic mute (0x1) and speaker mute (0x2) LEDs
are virtually guaranteed to be identical for the HP ProBook 440/450 G8
variants with motherboard SSIDs 8A74/8A75 (BIOS T87) and 8A76/8A77 (BIOS
T88); especially since spare keyboard parts are interchangeable between
different revisions of the same notebook models, and thus necessarily
have the same slot pinouts.
Signed-off-by: Ilyas Gasanov <public@gsnoff.com>
Link: https://patch.msgid.link/20251202154930.74481-1-public@gsnoff.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a very large set of updates, as well as some more extensive
cleanup work from Morimto-san we've also added a generic SCDA class
driver for SoundWire devices enabling us to support many chips with
no custom code. There's also a batch of new drivers added for both
SoCs and CODECs.
- Added a SoundWire SCDA generic class driver, pulling in a little
regmap work to support it.
- A *lot* of cleaup and API improvement work from Morimoto-san.
- Lots of work on the existing Cirrus, Intel, Maxim and Qualcomm
drivers.
- Support for Allwinner A523, Mediatek MT8189, Qualcomm QCM2290,
QRB2210 and SM6115, SpacemiT K1, and TI TAS2568, TAS5802, TAS5806,
TAS5815, TAS5828 and TAS5830.
This also pulls in some gpiolib changes supporting shared GPIOs in the
core there so we can convert some of the ASoC drivers open coding
handling of that to the core functionality.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmkt6lUACgkQJNaLcl1U
h9D7dgf+JP2+yZIeRBud7CEO4Docda2uoRssT7GAIY/Rqrpem5FI0c0pWyZISvhn
scyjkoCrQfHEoeYrtC3l5bDI7F8o5Tc91hGzhJiCi3mb8jSwi+CaNIpR0Cet3epV
B9wQgzxlxbmKCxJRUYTPQF3n1uBJWc5EBHSc5QPddTZ0vdUfSlX0FAKHsabpmaOC
TpkdJnOlH8WUokmP3kP3TpzlflmOSLehnWX4BelJe5Os5O0PQpiKh/JG3oCYHSmc
yEbzCjOaya80HHn11FShOpy+B4b6sLUMcN+CAmDiLAdNFGvvjgmjpwwZtLYAm09Z
zFhN7XuVk1vXf+Zx/jHqYKaZtvvAsQ==
=Xwls
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v6.19
This is a very large set of updates, as well as some more extensive
cleanup work from Morimto-san we've also added a generic SCDA class
driver for SoundWire devices enabling us to support many chips with
no custom code. There's also a batch of new drivers added for both
SoCs and CODECs.
- Added a SoundWire SCDA generic class driver, pulling in a little
regmap work to support it.
- A *lot* of cleaup and API improvement work from Morimoto-san.
- Lots of work on the existing Cirrus, Intel, Maxim and Qualcomm
drivers.
- Support for Allwinner A523, Mediatek MT8189, Qualcomm QCM2290,
QRB2210 and SM6115, SpacemiT K1, and TI TAS2568, TAS5802, TAS5806,
TAS5815, TAS5828 and TAS5830.
This also pulls in some gpiolib changes supporting shared GPIOs in the
core there so we can convert some of the ASoC drivers open coding
handling of that to the core functionality.
My laptop, HP ProBook 450 G8 (32M40EA), has Realtek ALC236 codec on its
integrated sound card, and uses GPIO pins 0x2 and 0x1 for speaker mute
and mic mute LEDs correspondingly, as found out by me through hda-verb
invocations. This matches the GPIO masks used by the
alc236_fixup_hp_gpio_led() function.
PCI subsystem vendor and device IDs happen to be 0x103c and 0x8a75,
which has not been covered in the ALC2xx driver code yet.
Signed-off-by: Ilyas Gasanov <public@gsnoff.com>
Link: https://patch.msgid.link/20251125235441.53629-1-public@gsnoff.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Surface Pro 2 and 3 have a strange headphone frequency response
and miss most of the bass. I discovered connecting the HP out to the
main DAC fixes this. Maybe the other is mono or intentionally filtered
signal for the built-in speakers? (At least the Lenovo Ideapad 720S
(AMD) (0x17aa, 0x3812) exhibited the same problem, but I don't have it
anymore for testing V2 changes.)
Signed-off-by: René Rebe <rene@exactco.de>
Co-developed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251120.124240.139462482701146043.rene@exactco.de
Enable SPK Mute Led and Mic Mute Led for HP platform.
It was also integrated with Tas2781 supported.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>
From AudioDSP perspective, only gateway-related modules e.g.: Copier:
Small set of changes providing new feature which the driver is already
utilizing on the market - for its Long-Term-Support (LTS) devices.
The goal is to cover systems which shipped with invalid Non HDAudio Link
Table (NHLT) - not just the descriptors (headers), but cases where the
hardware configuration is invalid too. The table is part of the ACPI
tree and forcing BIOS updates is not a feasible solution. With the
override, the topology file can carry the hardware configuration
instead.
From AudioDSP perspective, only gateway-related modules e.g.: Copier
care about the procedure. To ensure correct order of operations when
initializing such modules, the overrides take precedence over what's
currently there in the NHLT.
Turns out the Apple MacPro 6,1 trashcan also needs the inverted jack
detection like Mac mini patched, too.
Signed-off-by: René Rebe <rene@exactco.de>
Cc: <sstable@vger.kernel.org>
Link: https://patch.msgid.link/20251117.182351.1595411649664739497.rene@exactco.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Bind the realtek codec to TAS2781 I2C audio amps on ASUS Xbox Ally
projects. While these projects work without a quirk, adding it increases
the output volume significantly.
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251026191635.2447593-2-lkml@antheas.dev
Currently, on ASUS projects, the TAS2781 codec attaches the speaker GPIO
to the first tasdevice_priv instance using devm. This causes
tas2781_read_acpi to fail on subsequent probes since the GPIO is already
managed by the first device. This causes a failure on Xbox Ally X,
because it has two amplifiers, and prevents us from quirking both the
Xbox Ally and Xbox Ally X in the realtek codec driver.
It is unnecessary to attach the GPIO to a device as it is static.
Therefore, instead of attaching it and then reading it when loading the
firmware, read its value directly in tas2781_read_acpi and store it in
the private data structure. Then, make reading the value non-fatal so
that ASUS projects that miss a speaker pin can still work, perhaps using
fallback firmware.
Fixes: 4e7035a75d ("ALSA: hda/tas2781: Add speaker id check for ASUS projects")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Reviewed-by: Baojun Xu <baojun.xu@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251026191635.2447593-1-lkml@antheas.dev
Same recipes as PTL for NVL-S from the Nova Lake family.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251104121650.21872-7-peter.ujfalusi@linux.intel.com
Add HDMI codec ID for Intel Nova Lake platform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251104121650.21872-3-peter.ujfalusi@linux.intel.com
The project hardware ID should be ALC287_FIXUP_TXNW2781_I2C,
not ALC287_FIXUP_TAS2781_I2C for HP Lampass projects.
Fixes: 7a39c723b7 ("ALSA: hda/tas2781: Add new quirk for HP new projects")
Signed-off-by: Baojun Xu <baojun.xu@ti.com>
Link: https://patch.msgid.link/20251112092609.15865-1-baojun.xu@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace hardcoded GPIO node value with a defined constant for better
code readability and maintainability.
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20251107024030.36712-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>:
This patchset has 4 fixes and some enhancements to the Elite DSP driver
support.
Fixes includes
- setting correct flags for expected behaviour of appl_ptr
- fix closing of copp instances
- fix buffer alignment.
- fix state checks before closing asm stream
Enhancements include:
- adding q6asm_get_hw_pointer and ack callback support
- simplify code via __free(kfree) mechanism.
- use spinlock guards
- few cleanups discovered during doing above 2.
There is another set of updates comming soon, which will add support
for early memory mapping and few more modules support in audioreach.
After restructuring and splitting the HDMI codec driver code, each
HDMI codec driver contains the own build_controls and build_pcms ops.
A copy-n-paste error put the wrong entries for nvhdmi-mcp driver; both
build_controls and build_pcms are swapped. Unfortunately both
callbacks have the very same form, and the compiler didn't complain
it, either. This resulted in a NULL dereference because the PCM
instance hasn't been initialized at calling the build_controls
callback.
Fix it by passing the proper entries.
Fixes: ad781b550f ("ALSA: hda/hdmi: Rewrite to new probe method")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220743
Link: https://patch.msgid.link/20251106104647.25805-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vaio RPL is equipped with ACL256, and needs a
fix to make the internal mic and headphone mic to work.
Also must to limits the internal microphone boost.
Signed-off-by: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>
Link: https://patch.msgid.link/20251029181152.389302-1-edson.drosdeck@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk for Victus 15-fa1xxx wasn't working on Victus 15-fa1031nt due to a different board id. This patch enables the existing quirk for the board id 8BC8.
Tested on HP Victus 15-fa1031nt (MB 8C2D). The LED behaviour works as intended.
Signed-off-by: Eren Demir <eren.demir2479090@gmail.com>
Link: https://patch.msgid.link/20251027110208.6481-1-eren.demir2479090@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set cs35l56_base->cal_index to the (zero-based) amp index derived
from cirrus,dev-index property.
This is so that factory calibration data will be written to the UEFI
array in the slot equal to the amp index, for compatibility with the
Windows driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251021105022.1013685-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Create debugfs files that can be used to perform factory calibration.
During manufacture, the production line must perform a factory calibration
of the amps. This commit adds this functionality via debugfs files.
As this is only needed during manufacture, there is no need for this to be
available in a normal system so a Kconfig item has been added to enable
this. The new Kconfig option is inside a sub-menu because items do not
group and indent if the parent is invisible or there are multiple parent
dependencies. Anyway the sub-menu reduces the clutter.
cs35l56_hda_apply_calibration() has been changed to return an error code
that can be reported back through the debugfs write. The original call to
this function doesn't check the return code because in normal use it
doesn't matter whether this fails - the firmware will default to a safe
calibration for the platform. But tooling using the debugfs files might
want to know if there was an error.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251021105022.1013685-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This laptop requires the same quirk as Lenovo Yoga9 14IAP7 for
fixing the bass speaker problems.
Use HDA_CODEC_QUIRK to match on the codec SSID to avoid conflict with
the Lenovo Legion Slim 7 16IRH8, which has the same PCI SSID.
Signed-off-by: J-Donald Tournier <jdtournier@gmail.com>
Link: https://patch.msgid.link/20251018145322.39119-1-jdournier@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A moderately large collection of driver specific fixes, plus a few new
quirks and device IDs. The NAU8821 changes are a little large but more
in mechanical ways than in ways that are complex.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmjxJVsACgkQJNaLcl1U
h9Cabwf9FFaS0tIbuFMeIGw66HIxWqk0othL43amNff3GSX1N5r3TmVvic7nqWsh
1vd9yGUSfCpzpXZ6/LKzbYmbaO9pr+wQZh9fMsFyYPoS19acfn8KAOIR7lnvP8Rx
zuCbK4/ghbjb0EqtNIUK9IoDhvfRjzeatHEHk9YLJHuzmschSKAEb5bMLhVXUux+
eSwBXV87uzS+xuzv5/VTZ9JSnOpggjtPEXQtJSqGB8/PmaNQreyVqpjGJM6HZx/D
3j9GFgqsYn7K3ZXFSvh4mXXEVQ0fj7s3a+8uFsQ0V9QXyLrL7gj5oyYH9CxXZPoc
YT/2rJHL+tAMDjLBPjg7FM8y7bxOcQ==
=dB5E
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.18-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.18
A moderately large collection of driver specific fixes, plus a few new
quirks and device IDs. The NAU8821 changes are a little large but more
in mechanical ways than in ways that are complex.
The software reset for TAS5825 is different form other chips, as it will
set as 0x11 instead of 0x1 during reset in the tasdevice_reset(). So set
tas2781_hda::tasdevice_priv::chip_id as TAS5825, tasdevice_reset() can
work correctly.
Fixes: 7ceb69ca82 ("ASoC: tas2781: Add tas2118, tas2x20, tas5825 support")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP ZBook 17 G6 with SSID 103c:860c requires a similar workaround as
its 15-inch model in order to make the speaker and mute LED working.
Add the corresponding quirk entry to address it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220372
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
