While rfcomm_recv_frame() verifies that skb->len is at least
sizeof(*hdr) + 1 (4 bytes: 3-byte header + 1-byte FCS), an RFCOMM frame
with an extended 2-byte length field (!__test_ea(hdr->len)) has a 4-byte
header plus a 1-byte FCS (5 bytes minimum, sizeof(*hdr) + 2).
When a 4-byte RFCOMM frame with EA == 0 arrives:
1. The initial skb->len < sizeof(*hdr) + 1 check passes (4 < 4 is false).
2. Trimming the FCS byte decrements skb->len to 3.
3. If __check_fcs() succeeds, skb_pull(skb, 4) fails (4 > 3) and returns
NULL without advancing skb->data.
4. Because the return value of skb_pull() is ignored, the un-pulled
3-byte struct rfcomm_hdr remains at skb->data and is either queued as
application payload via rfcomm_recv_data() or parsed as a multiplexer
control command via rfcomm_recv_mcc() on DLCI 0.
Fix this by extending the length check in rfcomm_recv_frame() to also
require skb->len >= sizeof(*hdr) + 2 when !__test_ea(hdr->len).
Fixes: b230e5bf50 ("Bluetooth: RFCOMM: validate skb length in rfcomm_recv_frame")
Assisted-by: LLM
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The RFCOMM_CONNINFO getsockopt handler accepts a socket that is not
connected as long as deferred setup is enabled:
if (sk->sk_state != BT_CONNECTED &&
!rfcomm_pi(sk)->dlc->defer_setup) {
err = -ENOTCONN;
break;
}
l2cap_sk = rfcomm_pi(sk)->dlc->session->sock->sk;
dlc->defer_setup is set in rfcomm_sock_init() when rfcomm_connect_ind()
creates a child socket for an incoming connection on a listening socket
that has BT_DEFER_SETUP enabled. It is never cleared afterwards. The
session, however, can go away underneath it.
rfcomm_recv_disc() forces the dlc state before tearing it down:
d->state = BT_CLOSED;
__rfcomm_dlc_close(d, err);
The RFCOMM_DEFER_SETUP early return in __rfcomm_dlc_close() only covers
BT_CONNECT, BT_CONFIG, BT_OPEN and BT_CONNECT2, so with the state
already BT_CLOSED that switch does not match and the function falls
through to rfcomm_dlc_unlink(), which sets d->session = NULL, while
d->defer_setup stays 1.
A getsockopt(SOL_RFCOMM, RFCOMM_CONNINFO) on the accepted socket after
that point therefore skips the -ENOTCONN path -- sk->sk_state is
BT_CLOSED, but dlc->defer_setup is still set -- and dereferences the
NULL session. No race is needed: once the DISC has been processed, the
dereference is unconditional.
Reproduced on a KASAN kernel under QEMU with a BR/EDR peer emulated over
/dev/vhci: the peer brings up an ACL link, opens L2CAP on the RFCOMM
PSM, starts a session and sends SABM for a channel bound with
BT_DEFER_SETUP, and sends DISC for that dlci after the socket has been
accepted. getsockopt(SOL_RFCOMM, RFCOMM_CONNINFO) on the accepted
socket then hits:
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000002: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 1 UID: 0 PID: 150 Comm: init Tainted: G B 7.3.0-rc3-g5dd1818b15d9
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:rfcomm_sock_getsockopt+0x529/0x780
Call Trace:
<TASK>
do_sock_getsockopt+0x3ad/0x7d0
__sys_getsockopt+0x10e/0x1b0
__x64_sys_getsockopt+0xc2/0x160
do_syscall_64+0xda/0x4b0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
0x10 is the offset of sock in struct rfcomm_session;
rfcomm_sock_getsockopt_old() is inlined into rfcomm_sock_getsockopt().
Commit 43a556b2fd ("Bluetooth: RFCOMM: take rfcomm_mutex for the
deferred setup accept") fixed the same "a remote DISC clears the session
while deferred setup is still flagged" problem in rfcomm_dlc_accept();
this is the remaining instance of it, in the getsockopt path.
Deferred setup only leaves a socket usable here once it has reached
BT_CONNECT2, so restrict the exception to that state and check that a
session is actually present before following it.
Fixes: bb23c0ab82 ("Bluetooth: Add support for deferring RFCOMM connection setup")
Cc: stable@vger.kernel.org
Assisted-by: LLM
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_sock_cleanup_listen() closes unaccepted child sockets through
rfcomm_sock_close(), which takes the child socket lock before
rfcomm_dlc_close() acquires rfcomm_mutex. The RFCOMM worker takes these
locks in reverse order while handling connections and DLC state changes,
so lockdep reports a possible deadlock.
Close dequeued children without taking their socket lock. The accept queue
owns a reference to each child, and bt_accept_dequeue() locks the child
while unlinking it and clearing its parent pointer.
Dropping the child lock makes it important to prevent a concurrent
rfcomm_connect_ind() from enqueueing a new child after cleanup observes an
empty queue. Set a listening socket to BT_CLOSED while its lock is still
held, before dropping the lock and draining the queue. The state check in
rfcomm_connect_ind() then rejects new children once cleanup starts.
Reported-by: syzbot+0cece8fa7d83523f47a3@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=0cece8fa7d83523f47a3
Fixes: b7ce436a5d ("Bluetooth: switch to lock_sock in RFCOMM")
Signed-off-by: Juan Perdomo <jcperdomo100@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_kill_listener() walks session_list and deletes every session
without holding rfcomm_mutex, unlike the normal session processing and
connect error paths.
Under normal operation, an open RFCOMM socket pins rfcomm.ko, so
rfcomm_kill_listener() does not run concurrently with rfcomm_dlc_open().
However, forced module unload via delete_module(O_TRUNC) can stop
krfcommd while a failed connect is still unwinding.
connect task forced unload / krfcommd
------------ ------------------------
rfcomm_lock()
rfcomm_session_add()
delete_module("rfcomm", O_TRUNC)
rfcomm_kill_listener()
fetch session from session_list
kernel_connect() fails
rfcomm_session_del()
remove and free session
rfcomm_session_del(session)
The final call then reads the freed session and may corrupt the list.
KASAN reported with mdelay() to enlarge critical window:
BUG: KASAN: slab-use-after-free in rfcomm_run+0x3802/0x3f00 [rfcomm]
Read of size 8 at addr ffff888111058d40 by task krfcommd/79
Tainted: [R]=FORCED_RMMOD
Allocated by task 86:
rfcomm_session_add+0xa1/0x300 [rfcomm]
rfcomm_dlc_open+0x8b2/0xf30 [rfcomm]
rfcomm_sock_connect+0x34c/0x530 [rfcomm]
Freed by task 86:
kfree+0x121/0x3c0
rfcomm_dlc_open+0xab7/0xf30 [rfcomm]
rfcomm_sock_connect+0x34c/0x530 [rfcomm]
Hold rfcomm_mutex across the teardown traversal so every reachable
session_list walk uses the same serialization.
Reviewed-by: Ali Ahmet Memis <ali@iusegentoo.com>
Tested-by: Ali Ahmet Memis <ali@iusegentoo.com>
Reviewed-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_security_cfm() looks up a session on session_list and then walks
its DLC list without holding rfcomm_mutex. Since RFCOMM session teardown
uses rfcomm_mutex, krfcommd can close and free the same session and DLCs
concurrently:
hci_rx_work krfcommd
----------- ---------
rfcomm_session_get()
rfcomm_lock()
rfcomm_session_close()
rfcomm_dlc_unlink()
rfcomm_session_del()
kfree(s)
rfcomm_unlock()
walk s->dlcs
The callback can then read a freed session list head and touch freed DLCs
while updating their flags or timers.
Serialize the session lookup and DLC traversal in rfcomm_security_cfm()
with rfcomm_mutex. This matches the existing RFCOMM session lifetime
rules and prevents concurrent rfcomm_session_del() / rfcomm_dlc_unlink()
from tearing the objects down while the callback is using them.
KASAN reported:
BUG: KASAN: slab-use-after-free in rfcomm_security_cfm+0x41c/0x440
Read of size 8 at addr ffff888111fb3960 by task kworker/u17:1/89
Workqueue: hci0 hci_rx_work
Call Trace:
rfcomm_security_cfm+0x41c/0x440
hci_encrypt_cfm+0x139/0x590
hci_encrypt_change_evt+0x37b/0xc40
hci_event_packet+0x71b/0xb20
hci_rx_work+0x293/0x730
Allocated by task 69:
rfcomm_session_add+0x9e/0x2f0
rfcomm_run+0x44b/0x41e0
Freed by task 69:
kfree+0x131/0x3c0
rfcomm_session_del+0x188/0x220
rfcomm_run+0x1985/0x41e0
Fixes: 08c30aca9e ("Bluetooth: Remove RFCOMM session refcnt")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_apply_pn() accepts the MTU value from a remote PN (Parameter
Negotiation) frame without checking for zero. When the remote peer
sends an MTU of zero, d->mtu is set to 0. This causes the sendmsg
path to enter an infinite loop when fragmenting data, as each fragment
has size == min_t(size_t, len, 0) == 0, so the remaining length never
decreases. The infinite allocation of zero-length skbs exhausts all
system memory.
Fix by clamping d->mtu to RFCOMM_DEFAULT_MTU when the negotiated
value is zero, consistent with the initial value assigned in
rfcomm_dlc_alloc().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_sock_recvmsg() completes a deferred setup by calling
rfcomm_dlc_accept() without holding any RFCOMM lock:
if (test_and_clear_bit(RFCOMM_DEFER_SETUP, &d->flags)) {
rfcomm_dlc_accept(d);
return 0;
}
and rfcomm_dlc_accept() dereferences the session on its first line:
struct sock *sk = d->session->sock->sk;
Every other path that touches d->session runs under rfcomm_mutex:
rfcomm_dlc_open(), rfcomm_dlc_close(), rfcomm_dlc_exists(),
rfcomm_dlc_send_rpn(), and the RFCOMM thread through
rfcomm_process_sessions(). rfcomm_connect_ind() is even documented as
"called under rfcomm_lock()". This call site is the only one that skips
it.
The RFCOMM_DEFER_SETUP bit looks like it serialises the accept against
teardown, since __rfcomm_dlc_close() returns early when it wins the
test_and_clear. But rfcomm_recv_disc() forces the state first:
d->state = BT_CLOSED;
__rfcomm_dlc_close(d, err);
and the early return only covers BT_CONNECT, BT_CONFIG, BT_OPEN and
BT_CONNECT2. With the state already BT_CLOSED that switch does not
match, the bit is never consulted, and __rfcomm_dlc_close() falls
through to rfcomm_dlc_unlink(), which sets d->session = NULL.
So a remote DISC on a deferred dlc clears the session while leaving
RFCOMM_DEFER_SETUP set. The next recvmsg() then passes the
test_and_clear and dereferences a NULL session. No timing window is
needed: once the DISC has been processed, the dereference is
unconditional.
Give rfcomm_dlc_accept() the same shape as rfcomm_dlc_open() and
rfcomm_dlc_close(): an exported wrapper that takes rfcomm_mutex and
re-checks the session, around a __rfcomm_dlc_accept() that the two
in-core callers, which already hold the mutex, keep using.
Reproduced on a KASAN + PROVE_LOCKING kernel with a BR/EDR peer emulated
over /dev/vhci: the peer brings up an ACL link, opens L2CAP on the
RFCOMM PSM, starts a session, opens a dlc on a channel bound with
BT_DEFER_SETUP, and sends DISC after the socket is accepted. recv() on
the accepted socket then hits:
Oops: general protection fault
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
RIP: 0010:rfcomm_dlc_accept+0x54/0x350
Call Trace:
rfcomm_sock_recvmsg+0x1cd/0x230
sock_recvmsg+0x166/0x1c0
__sys_recvfrom+0x20d/0x300
0x10 is the offset of sock in struct rfcomm_session. With this patch the
same run completes with recv() returning 0 and no report, and lockdep
stays quiet, confirming rfcomm_mutex is still taken before lock_sock on
this path as it is on the thread side.
Fixes: bb23c0ab82 ("Bluetooth: Add support for deferring RFCOMM connection setup")
Cc: stable@vger.kernel.org
Signed-off-by: Ali Ahmet Memis <ali@iusegentoo.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The modules rfcomm (BT_RFCOMM), bnep (BT_BNEP), hidp (BT_HIDP), and
bluetooth_6lowpan (BT_6LOWPAN) are dependent on the bluetooth module
(BT, tristate) only transitively through the boolean BT_BREDR for the
first three and through the boolean BT_LE for the bluetooth_6lowpan.
Therefore, the modules can be selected as built-in even if the BT=m.
The combination of BT=m and =y for the said modules leads to the kernel
build system silently ignoring those modules, without ever compiling
them as built-in or as loadable modules.
Add BT as a direct dependency to the Kconfig of rfcomm, bnep, hidp, and
bluetooth_6lowpan. The modules set to =y when BT=m will default to =m,
rather then getting silently ignored by the build system.
Signed-off-by: Iva Kasprzaková <iva@yenya.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Enable compiler context analysis for Bluetooth subsystem and drivers.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add minimal compiler context analysis annotations, required for
compilation to pass.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_recv_frame() casts skb->data to struct rfcomm_hdr and dereferences
hdr->addr and hdr->ctrl without validating skb->len first. A truncated
frame with skb->len less than the minimum header size causes an
out-of-bounds read of uninitialized memory. Additionally, a zero-length
frame causes skb->len-- to underflow to UINT_MAX, making
skb_tail_pointer() read far past the buffer.
Commit 23882b828c ("Bluetooth: RFCOMM: validate skb length in MCC
handlers") fixed the same class of missing-length-check bugs in the MCC
sub-handlers, but the top-level rfcomm_recv_frame() was left unfixed.
KMSAN reports:
BUG: KMSAN: uninit-value in rfcomm_run
...
Uninit was created at:
__alloc_skb+0x474/0xb60
vhci_write+0xe9/0x870
Fix this by rejecting frames smaller than sizeof(struct rfcomm_hdr) + 1
(the minimum frame must have a 3-byte header and a 1-byte FCS).
Signed-off-by: Jiale Yao <yaojiale02@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_tty_set_termios() tests dlc->session without rfcomm_mutex and
later passes the pointer to rfcomm_send_rpn(). The latter dereferences
both session->initiator and session->sock. Meanwhile, krfcommd can
unlink the DLC and free the session while holding rfcomm_mutex.
The race can proceed as follows:
TTY ioctl task krfcommd
-------------- --------
load dlc->session
enter rfcomm_send_rpn()
lock rfcomm_mutex
clear dlc->session
free session
unlock rfcomm_mutex
read session->initiator
KASAN reported:
BUG: KASAN: slab-use-after-free in rfcomm_send_rpn+0x297/0x2a0
Read of size 4 at addr ffff88810012a850 by task poc/92
Call Trace:
rfcomm_send_rpn+0x297/0x2a0
rfcomm_tty_set_termios+0x50d/0x850
tty_set_termios+0x596/0x950
set_termios+0x46a/0x6e0
tty_mode_ioctl+0x152/0xbd0
tty_ioctl+0x915/0x1240
__x64_sys_ioctl+0x134/0x1c0
Allocated by task 92:
rfcomm_session_add+0x9e/0x2e0
rfcomm_dlc_open+0x8b1/0xe00
rfcomm_dev_activate+0x85/0x1a0
rfcomm_tty_open+0x90/0x280
Freed by task 68:
kfree+0x131/0x3c0
rfcomm_session_del+0x119/0x180
rfcomm_run+0x737/0x4710
Add rfcomm_dlc_send_rpn(), which holds rfcomm_mutex while it verifies
that the DLC is still attached and sends the RPN frame. Have the TTY
path use the helper and drop its unlocked session check. This keeps the
session valid through both the frame construction and socket send.
Fixes: 3a5e903c09 ("[Bluetooth]: Implement RFCOMM remote port negotiation")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Many bluetooth source files are missing SPDX-License-Identifier
lines. Add appropriate IDs to these files, and remove other
license lines from the headers.
Leave the warranty disclaimer in files where the license ID is
GPL-2.0 but the wording of the disclaimer is slightly different
from that of the GPL v2 disclaimer.
It is not different enough to cause licensing conflicts, but is
kept to honor the original contributors' legal intent.
Signed-off-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Convert RFCOMM socket's getsockopt implementation to use the new
getsockopt_iter callback with sockopt_t.
Key changes:
- Replace (char __user *optval, int __user *optlen) with sockopt_t *sopt
- Use sopt->optlen for buffer length (input)
- Use copy_to_iter() instead of put_user()/copy_to_user()
- Add linux/uio.h for copy_to_iter()
The sockopt_t parameter is named sopt rather than opt to avoid
collision with the existing local u32 opt used by RFCOMM_LM.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The RFCOMM MCC handlers cast skb->data to protocol-specific structs
without validating skb->len first. A malicious remote device can send
truncated MCC frames and trigger out-of-bounds reads in these handlers.
Fix this by using skb_pull_data() to validate and access the required
data before dereferencing it.
rfcomm_recv_rpn() requires special handling since ETSI TS 07.10 allows
1-byte RPN requests. Handle this by validating only the DLCI byte first,
and validating the full struct only when len > 1.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Suggested-by: Muhammad Bilal <meatuni001@gmail.com>
Signed-off-by: SeungJu Cheon <suunj1331@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_get_sock_by_channel() scans rfcomm_sk_list under the list lock,
but returns the selected listener after dropping that lock without
taking a reference. rfcomm_connect_ind() then locks the listener,
queues a child socket on it, and may notify it after unlocking it.
The buggy scenario involves two paths, with each column showing the
order within that path:
rfcomm_connect_ind(): listener close:
1. Find parent in 1. close() enters
rfcomm_get_sock_by_channel() rfcomm_sock_release().
2. Drop rfcomm_sk_list.lock 2. rfcomm_sock_shutdown()
without pinning parent. closes the listener.
3. Call lock_sock(parent) and 3. rfcomm_sock_kill()
bt_accept_enqueue(parent, unlinks and puts parent.
sk, true).
4. Read parent flags and may 4. parent can be freed.
call sk_state_change().
If close wins the race, parent can be freed before
rfcomm_connect_ind() reaches lock_sock(), bt_accept_enqueue(), or the
deferred-setup callback.
Take a reference on the listener before leaving rfcomm_sk_list.lock.
After lock_sock() succeeds, recheck that it is still in BT_LISTEN
before queueing a child, cache the deferred-setup bit while the parent
is locked, and drop the reference after the last parent use.
KASAN reported a slab-use-after-free in lock_sock_nested() from
rfcomm_connect_ind(), with the freeing stack going through
rfcomm_sock_kill() and rfcomm_sock_release().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhang Cen <rollkingzzc@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
bt_accept_dequeue() unlinks a not-yet-accepted child from the parent
accept queue and release_sock()s it before returning, so the returned
sk has no caller reference and is unlocked.
l2cap_sock_cleanup_listen() walks these children on listening-socket
close. A concurrent HCI disconnect drives hci_rx_work ->
l2cap_conn_del() which runs l2cap_chan_del() + l2cap_sock_kill() and
frees the child sk and its l2cap_chan; cleanup_listen() then uses both:
BUG: KASAN: slab-use-after-free in l2cap_sock_kill
l2cap_sock_kill / l2cap_sock_cleanup_listen / __x64_sys_close
Freed by: l2cap_conn_del -> l2cap_sock_close_cb -> l2cap_sock_kill
This is distinct from the two fixes already in this area: commit
e83f5e24da ("Bluetooth: serialize accept_q access") serialises the
accept_q list/poll and takes temporary refs inside bt_accept_dequeue(),
and CVE-2025-39860 serialises the userspace close()/accept() race by
calling cleanup_listen() under lock_sock() in l2cap_sock_release().
Neither covers l2cap_conn_del() running from hci_rx_work, so this UAF
still reproduces on current bluetooth/master.
Take the reference at the source: bt_accept_dequeue() does sock_hold()
while sk is still locked, before release_sock(); callers sock_put().
cleanup_listen() pins the chan with l2cap_chan_hold_unless_zero() under
a brief child sk lock (serialising vs l2cap_sock_teardown_cb()), drops
it before l2cap_chan_lock(), and skips a duplicate l2cap_sock_kill() on
SOCK_DEAD. conn->lock is not taken here: cleanup_listen() runs under
the parent sk lock and that would invert
conn->lock -> chan->lock -> sk_lock (lockdep).
KASAN/SMP: an unprivileged listen/close vs HCI-disconnect race produced
12 use-after-free reports per run before this change; 0, and no lockdep
report, over 1600+ raced iterations after it on bluetooth/master.
Fixes: 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
Cc: stable@vger.kernel.org
Reported-by: Siwei Zhang <oss@fourdim.xyz>
Reviewed-by: Siwei Zhang <oss@fourdim.xyz>
Signed-off-by: Safa Karakuş <safa.karakus@secunnix.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
rfcomm_recv_data() treats the first payload byte as a credit field when
the UIH frame carries PF and credit-based flow control is enabled.
After the header has been stripped, the PF/CFC path consumes that byte
with a direct skb->data dereference followed by skb_pull(). A malformed
short frame can reach this path without a byte available.
Use skb_pull_data() so the length check and pull happen together before
the returned credit byte is consumed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Update all struct proto_ops connect() callback function prototypes from
"struct sockaddr *" to "struct sockaddr_unsized *" to avoid lying to the
compiler about object sizes. Calls into struct proto handlers gain casts
that will be removed in the struct proto conversion patch.
No binary changes expected.
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20251104002617.2752303-3-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update all struct proto_ops bind() callback function prototypes from
"struct sockaddr *" to "struct sockaddr_unsized *" to avoid lying to the
compiler about object sizes. Calls into struct proto handlers gain casts
that will be removed in the struct proto conversion patch.
No binary changes expected.
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20251104002617.2752303-2-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RFCOMM driver confuses the local and remote modem control signals,
which specifically means that the reported DTR and RTS state will
instead reflect the remote end (i.e. DSR and CTS).
This issue dates back to the original driver (and a follow-on update)
merged in 2002, which resulted in a non-standard implementation of
TIOCMSET that allowed controlling also the TS07.10 IC and DV signals by
mapping them to the RI and DCD input flags, while TIOCMGET failed to
return the actual state of DTR and RTS.
Note that the bogus control of input signals in tiocmset() is just
dead code as those flags will have been masked out by the tty layer
since 2003.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core & protocols
----------------
- Wrap datapath globals into net_aligned_data, to avoid false sharing.
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container).
- Add SO_INQ and SCM_INQ support to AF_UNIX.
- Add SIOCINQ support to AF_VSOCK.
- Add TCP_MAXSEG sockopt to MPTCP.
- Add IPv6 force_forwarding sysctl to enable forwarding per interface.
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB.
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users.
- Convert TCP send queue handling from tasklet to BH workque.
- Improve BPF iteration over TCP sockets to see each socket exactly once.
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code.
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel NAPI
thread when threaded NAPI gets disabled. Previously thread would stick
around until ifdown due to tricky synchronization.
- Allow multicast routing to take effect on locally-generated packets.
- Add output interface argument for End.X in segment routing.
- MCTP: add support for gateway routing, improve bind() handling.
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink.
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed.
- Support NUD_PERMANENT for proxy neighbor entries.
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM.
- Add sequence numbers to netconsole messages. Unregister netconsole's
console when all net targets are removed. Code refactoring.
Add a number of selftests.
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup.
- Support inspecting ref_tracker state via DebugFS.
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links.
- Allow providing upcall pid for the 'execute' command in openvswitch.
- Remove DCCP support from Netfilter's conntrack.
- Disallow multiple packet duplications in the queuing layer.
- Prevent use of deprecated iptables code on PREEMPT_RT.
Driver API
----------
- Support RSS and hashing configuration over ethtool Netlink.
- Add dedicated ethtool callbacks for getting and setting hashing fields.
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc.
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs.
- Support traffic classes in devlink rate API for bandwidth management.
- Remove rtnl_lock dependency from UDP tunnel port configuration.
Device drivers
--------------
- Add a new Broadcom driver for 800G Ethernet (bnge).
- Add a standalone driver for Microchip ZL3073x DPLL.
- Remove IBM's NETIUCV device driver.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is used
by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=lqbe
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
This code (tty_get -> vhangup -> tty_put) is repeated on few places.
Introduce a helper similar to tty_port_tty_hangup() (asynchronous) to
handle even vhangup (synchronous).
And use it on those places.
In fact, reuse the tty_port_tty_hangup()'s code and call tty_vhangup()
depending on a new bool parameter.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit 4d94f05558 which has
problems (see [1]) and is no longer needed since 581dd2dc16
("Bluetooth: hci_event: Fix using rcu_read_(un)lock while iterating")
has reworked the code where the original bug has been found.
[1] Link: https://lore.kernel.org/linux-bluetooth/877c55ci1r.wl-tiwai@suse.de/T/#t
Fixes: 4d94f05558 ("Bluetooth: hci_core: Fix sleeping function called from invalid context")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use usb_autopm_get_interface() and usb_autopm_put_interface()
in btmtk_usb_shutdown(), it could send func ctrl after enabling
autosuspend.
Bluetooth: btmtk_usb_hci_wmt_sync() hci0: Execution of wmt command
timed out
Bluetooth: btmtk_usb_shutdown() hci0: Failed to send wmt func ctrl
(-110)
Fixes: 5c5e8c52e3 ("Bluetooth: btmtk: move btusb_mtk_[setup, shutdown] to btmtk.c")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The bt_copy_from_sockptr() return value is being misinterpreted by most
users: a non-zero result is mistakenly assumed to represent an error code,
but actually indicates the number of bytes that could not be copied.
Remove bt_copy_from_sockptr() and adapt callers to use
copy_safe_from_sockptr().
For sco_sock_setsockopt() (case BT_CODEC) use copy_struct_from_sockptr() to
scrub parts of uninitialized buffer.
Opportunistically, rename `len` to `optlen` in hci_sock_setsockopt_old()
and hci_sock_setsockopt().
Fixes: 51eda36d33 ("Bluetooth: SCO: Fix not validating setsockopt user input")
Fixes: a97de7bff1 ("Bluetooth: RFCOMM: Fix not validating setsockopt user input")
Fixes: 4f3951242a ("Bluetooth: L2CAP: Fix not validating setsockopt user input")
Fixes: 9e8742cdfc ("Bluetooth: ISO: Fix not validating setsockopt user input")
Fixes: b2186061d6 ("Bluetooth: hci_sock: Fix not validating setsockopt user input")
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: David Wei <dw@davidwei.uk>
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 9bf4e919cc worked around an issue introduced after an innocuous
optimisation change in LLVM main:
> len is defined as an 'int' because it is assigned from
> '__user int *optlen'. However, it is clamped against the result of
> sizeof(), which has a type of 'size_t' ('unsigned long' for 64-bit
> platforms). This is done with min_t() because min() requires compatible
> types, which results in both len and the result of sizeof() being casted
> to 'unsigned int', meaning len changes signs and the result of sizeof()
> is truncated. From there, len is passed to copy_to_user(), which has a
> third parameter type of 'unsigned long', so it is widened and changes
> signs again. This excessive casting in combination with the KCSAN
> instrumentation causes LLVM to fail to eliminate the __bad_copy_from()
> call, failing the build.
The same issue occurs in rfcomm in functions rfcomm_sock_getsockopt and
rfcomm_sock_getsockopt_old.
Change the type of len to size_t in both rfcomm_sock_getsockopt and
rfcomm_sock_getsockopt_old and replace min_t() with min().
Cc: stable@vger.kernel.org
Co-authored-by: Aleksei Vetrov <vvvvvv@google.com>
Improves: 9bf4e919cc ("Bluetooth: Fix type of len in {l2cap,sco}_sock_getsockopt_old()")
Link: https://github.com/ClangBuiltLinux/linux/issues/2007
Link: https://github.com/llvm/llvm-project/issues/85647
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
bt_sock_alloc() attaches allocated sk object to the provided sock object.
If rfcomm_dlc_alloc() fails, we release the sk object, but leave the
dangling pointer in the sock object, which may cause use-after-free.
Fix this by swapping calls to bt_sock_alloc() and rfcomm_dlc_alloc().
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241014153808.51894-4-ignat@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rfcomm_sk_state_change attempts to use sock_lock so it must never be
called with it locked but rfcomm_sock_ioctl always attempt to lock it
causing the following trace:
======================================================
WARNING: possible circular locking dependency detected
6.8.0-syzkaller-08951-gfe46a7dd189e #0 Not tainted
------------------------------------------------------
syz-executor386/5093 is trying to acquire lock:
ffff88807c396258 (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1671 [inline]
ffff88807c396258 (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+.}-{0:0}, at: rfcomm_sk_state_change+0x5b/0x310 net/bluetooth/rfcomm/sock.c:73
but task is already holding lock:
ffff88807badfd28 (&d->lock){+.+.}-{3:3}, at: __rfcomm_dlc_close+0x226/0x6a0 net/bluetooth/rfcomm/core.c:491
Reported-by: syzbot+d7ce59b06b3eb14fd218@syzkaller.appspotmail.com
Tested-by: syzbot+d7ce59b06b3eb14fd218@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=d7ce59b06b3eb14fd218
Fixes: 3241ad820d ("[Bluetooth] Add timestamp support to L2CAP, RFCOMM and SCO")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Refactor the list_for_each_entry() loop of rfcomm_get_dev_list()
function to use array indexing instead of pointer arithmetic.
This way, the code is more readable and idiomatic.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is an effort to get rid of all multiplications from allocation
functions in order to prevent integer overflows [1][2].
As the "dl" variable is a pointer to "struct rfcomm_dev_list_req" and
this structure ends in a flexible array:
struct rfcomm_dev_list_req {
[...]
struct rfcomm_dev_info dev_info[];
};
the preferred way in the kernel is to use the struct_size() helper to
do the arithmetic instead of the calculation "size + count * size" in
the kzalloc() and copy_to_user() functions.
At the same time, prepare for the coming implementation by GCC and Clang
of the __counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time via
CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE (for
strcpy/memcpy-family functions).
In this case, it is important to note that the logic needs a little
refactoring to ensure that the "dev_num" member is initialized before
the first access to the flex array. Specifically, add the assignment
before the list_for_each_entry() loop.
Also remove the "size" variable as it is no longer needed.
This way, the code is more readable and safer.
This code was detected with the help of Coccinelle, and audited and
modified manually.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/160 [2]
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Rather than pass in flags, error pointer, and whether this is a kernel
invocation or not, add a struct proto_accept_arg struct as the argument.
This then holds all of these arguments, and prepares accept for being
able to pass back more information.
No functional changes in this patch.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
syzbot reported rfcomm_sock_setsockopt_old() is copying data without
checking user input length.
BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset
include/linux/sockptr.h:49 [inline]
BUG: KASAN: slab-out-of-bounds in copy_from_sockptr
include/linux/sockptr.h:55 [inline]
BUG: KASAN: slab-out-of-bounds in rfcomm_sock_setsockopt_old
net/bluetooth/rfcomm/sock.c:632 [inline]
BUG: KASAN: slab-out-of-bounds in rfcomm_sock_setsockopt+0x893/0xa70
net/bluetooth/rfcomm/sock.c:673
Read of size 4 at addr ffff8880209a8bc3 by task syz-executor632/5064
Fixes: 9f2c8a03fb ("Bluetooth: Replace RFCOMM link mode with security level")
Fixes: bb23c0ab82 ("Bluetooth: Add support for deferring RFCOMM connection setup")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During our fuzz testing of the connection and disconnection process at the
RFCOMM layer, we discovered this bug. By comparing the packets from a
normal connection and disconnection process with the testcase that
triggered a KASAN report. We analyzed the cause of this bug as follows:
1. In the packets captured during a normal connection, the host sends a
`Read Encryption Key Size` type of `HCI_CMD` packet
(Command Opcode: 0x1408) to the controller to inquire the length of
encryption key.After receiving this packet, the controller immediately
replies with a Command Completepacket (Event Code: 0x0e) to return the
Encryption Key Size.
2. In our fuzz test case, the timing of the controller's response to this
packet was delayed to an unexpected point: after the RFCOMM and L2CAP
layers had disconnected but before the HCI layer had disconnected.
3. After receiving the Encryption Key Size Response at the time described
in point 2, the host still called the rfcomm_check_security function.
However, by this time `struct l2cap_conn *conn = l2cap_pi(sk)->chan->conn;`
had already been released, and when the function executed
`return hci_conn_security(conn->hcon, d->sec_level, auth_type, d->out);`,
specifically when accessing `conn->hcon`, a null-ptr-deref error occurred.
To fix this bug, check if `sk->sk_state` is BT_CLOSED before calling
rfcomm_recv_frame in rfcomm_process_rx.
Signed-off-by: Yuxuan Hu <20373622@buaa.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
tty_operations::send_xchar is one of the last users of 'char' type for
characters in the tty layer. Convert it to u8 now.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-bluetooth@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20231206073712.17776-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
Unify the type of tty_operations::write() counters with the 'count'
parameter. I.e. use size_t for them.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20230810091510.13006-37-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This consolidates code around sk_alloc into bt_sock_alloc which does
take care of common initialization.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
tty->driver_data is 'void *', so there is no need to cast from that.
Therefore remove the casts and assign the pointer directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Link: https://lore.kernel.org/r/20230731080244.2698-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/itAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykJbQCfWv/J4ZElO108iHBU5mJCDagUDBgAnAtLLN6A
SEAnnokGCDtA/BNIXeES
=luRi
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
