The Linux Version Code is currently written to the GUID register before
PHY initialization. Certain PHY implementations (such as Synopsys eUSB
PHY performing link_sw_reset) clear the GUID register to its default
value during initialization, causing the kernel version information to
be lost.
Move the GUID register programming to occur after PHY initialization
completes to ensure the Linux version information persists.
Fixes: fa0ea13e9f ("usb: dwc3: core: write LINUX_VERSION_CODE to our GUID register")
Cc: stable <stable@kernel.org>
Reported-by: Pritam Manohar Sutar <pritam.sutar@samsung.com>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260417063314.2359-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Microchip USB3340x ULPI PHY requires a delay when switching to the
high-speed transmitter. See:
http://ww1.microchip.com/downloads/en/DeviceDoc/80000645A.pdf
Module 2 "Device Enumeration Failure with Link IP Systems"
For details on the behavior and fix, refer to the AMD (formerly Xilinx)
forum post: "USB stuck in full speed mode with USB3340 ULPI PHY, ZynqMP."
This patch uses the USB PHY Vendor-ID and Product-ID to detect the
USB3340 PHY and then applies the necessary fix if this PHY is found.
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260305121452.54082-2-ingo.rohloff@lauterbach.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current design assumes that the controller remains powered when wakeup
is enabled. However, some SoCs provide wakeup capability even when the
controller itself is powered down, using separate dedicated wakeup logic.
This allows additional power savings, but requires the controller to be
fully re‑initialized after system resume.
To support these SoCs, introduce a flag needs_full_reinit for the purpose.
And the glue layer needs to indicate if the controller needs this behavior
by setting a same flag needs_full_reinit in dwc3_properties.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260212-add-flatten-dts-based-dwc3-imx-driver-v5-2-ff04a75ce221@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently dwc3_gadget_vbus_draw() can be called from atomic
context, which in turn invokes power-supply-core APIs. And
some these PMIC APIs have operations that may sleep, leading
to kernel panic.
Fix this by moving the vbus_draw into a workqueue context.
Fixes: 99288de360 ("usb: dwc3: add an alternate path in vbus_draw callback")
Cc: stable <stable@kernel.org>
Tested-by: Samuel Wu <wusamuel@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://patch.msgid.link/20260204054155.3063825-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple DWC3 controllers are being used, trace events from
different instances get mixed up making debugging difficult as
there's no way to distinguish which instance generated the trace.
Use the register base address of dwc3 controller and append it to
trace events, so that the source instance is clearly identifiable.
Example trace output,
before -> dwc3_event: event (00000101): Reset [U0]
after -> dwc3_event: 0x000000000a600000: event (00000101): Reset [U0]
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260122105000.4126769-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dwc pointer in dwc3_readl() dwc3_writel() instead of passing
the dwc->regs. This would help us access the dwc structure and
log the base address in traces. There's no functional changes in
this patch, just refactoring existing APIs.
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260114100748.2950103-3-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys renamed DWC_usb32 IP to DWC_usb4 as of IP version 1.30. No
functional change except checking for the IP_NAME here. The driver will
treat the new IP_NAME as if it's DWC_usb32. Additional features for USB4
will be introduced and checked separately.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/e6f1827754c7a7ddc5eb7382add20bfe3a9b312f.1767390747.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt driver updates for 6.19-rc1.
Nothing major here, just lots of tiny updates for most of the common USB
drivers. Included in here are:
- more xhci driver updates and fixes
- Thunderbolt driver cleanups
- usb serial driver updates
- typec driver updates
- USB tracepoint additions
- dwc3 driver updates, including support for Apple hardware
- lots of other smaller driver updates and cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaTTLNQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn29wCcD23xCSWuRIKHfSWlefCwptHKT0AAoM0NJdeO
C4/4pui5ifTu1g5Vud1r
=Sm/3
-----END PGP SIGNATURE-----
Merge tag 'usb-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
6.19-rc1. Nothing major here, just lots of tiny updates for most of
the common USB drivers. Included in here are:
- more xhci driver updates and fixes
- Thunderbolt driver cleanups
- usb serial driver updates
- typec driver updates
- USB tracepoint additions
- dwc3 driver updates, including support for Apple hardware
- lots of other smaller driver updates and cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (161 commits)
usb: gadget: tegra-xudc: Always reinitialize data toggle when clear halt
USB: serial: option: move Telit 0x10c7 composition in the right place
USB: serial: option: add Telit Cinterion FE910C04 new compositions
usb: typec: ucsi: fix use-after-free caused by uec->work
usb: typec: ucsi: fix probe failure in gaokun_ucsi_probe()
usb: dwc3: core: Remove redundant comment in core init
usb: phy: Initialize struct usb_phy list_head
USB: serial: option: add Foxconn T99W760
usb: usb-storage: No additional quirks need to be added to the EL-R12 optical drive.
usb: typec: hd3ss3220: Enable VBUS based on ID pin state
dt-bindings: usb: ti,hd3ss3220: Add support for VBUS based on ID state
usb: typec: anx7411: add WQ_PERCPU to alloc_workqueue users
USB: add WQ_PERCPU to alloc_workqueue users
dt-bindings: usb: dwc3-xilinx: Describe the reset constraint for the versal platform
drivers/usb/storage: use min() instead of min_t()
usb: raw-gadget: cap raw_io transfer length to KMALLOC_MAX_SIZE
usb: ohci-da8xx: remove unused platform data
usb: gadget: functionfs: use dma_buf_unmap_attachment_unlocked() helper
usb: uas: reduce time under spinlock
usb: dwc3: eic7700: Add EIC7700 USB driver
...
Remove redundant comment which was put in to address LLUCTL register
modifications for all applicable ports of multiport controller. Although
the support was added, the todo comment wasn't removed then.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20251116123033.131004-1-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://patch.msgid.link/20251111095117.95023-1-sakari.ailus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysdev_is_parent check was being used to infer PCI devices that have
the DMA mask set from the PCI capabilities, but sysdev_is_parent is also
used for non-PCI ACPI devices in which case the DMA mask would be the
bus default or as set by the _DMA method.
Without this fix the DMA mask would default to 32-bits and so allocation
would fail if there was no DRAM below 4GB.
Fixes: 47ce45906c ("usb: dwc3: leave default DMA for PCI devices")
Cc: stable <stable@kernel.org>
Signed-off-by: Jamie Iles <jamie.iles@oss.qualcomm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20251107104437.1602509-1-punit.agrawal@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need fine grained control over mode switched on the DWC3 controller
present on Apple Silicon. Export core, host and gadget init and exit,
ptrcap and susphy control functions. Also introduce an additional
parameter to probe_data that allows to skip the final initialization
step that would bring up host or gadget mode.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://patch.msgid.link/20251015-b4-aplpe-dwc3-v2-4-cbd65a2d511a@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add software-managed properties for the flattened model, which does not
need to use device tree properties to pass down information to the
common DWC3 core.
Add 'properties' in dwc3_probe_data and set default values for existing
users (dwc3-qcom, dwc3-generic-plat).
No functional changes.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250929-ls_dma_coherence-v5-2-2ebee578eb7e@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In certain situations like role switching, the glue layers need to be
informed of these events, so that they can take any necessary action.
But in non-flattened implementations, the glue drivers have no data on
when the core driver probe was successful post invoking of_platform_
populate. Now that the core driver supports flattened implementations
as well, introduce vendor callbacks that can be passed on from glue to
core before invoking dwc3_core_probe.
Introduce callbacks to notify glue layer of role_switch and run_stop
changes. These can be used by flattened implementation of Qualcomm
glue layer to generate connect/disconnect events in controller during
cable connect and run stop modifications by udc in device mode.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250907181412.2174616-2-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to the port capability can be indirectly observed by tracing
register writes to DWC3_GCTL. However, this requires interpreting the
raw value, which is neither intuitive nor precise for debugging.
Monitoring these mode changes is essential for resolving issues related
to USB role switching and enumeration.
Introduce a dedicated trace event to provide a human-readable log when
the port capability is configured.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250822092411.173519-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc3_gadget_soft_disconnect() fails, dwc3_suspend_common() keeps
going with the suspend, resulting in a period where the power domain is
off, but the gadget driver remains connected. Within this time frame,
invoking vbus_event_work() will cause an error as it attempts to access
DWC3 registers for endpoint disabling after the power domain has been
completely shut down.
Abort the suspend sequence when dwc3_gadget_suspend() cannot halt the
controller and proceeds with a soft connect.
Fixes: 9f8a67b65a ("usb: dwc3: gadget: fix gadget suspend/resume")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250528100315.2162699-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the core is integrated with glue, it's reasonable to assume that
the glue driver will have to touch the IP before/after the core takes
the hardware out and into reset. As such the glue must own these
resources and be allowed to turn them on/off outside the core's
handling.
Allow the platform or glue layer to indicate if the core logic for
clocks and resets should be skipped to deal with this.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-4-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 IP block is handled by three distinct device drivers: XHCI,
DWC3 core and a platform specific (optional) DWC3 glue driver.
This has resulted in, at least in the case of the Qualcomm glue, the
presence of a number of layering violations, where the glue code either
can't handle, or has to work around, the fact that core might not probe
deterministically.
An example of this is that the suspend path should operate slightly
different depending on the device operating in host or peripheral mode,
and the only way to determine the operating state is to peek into the
core's drvdata.
The Qualcomm glue driver is expected to make updates in the qscratch
register region (the "glue" region) during role switch events, but with
the glue and core split using the driver model, there is no reasonable
way to introduce listeners for mode changes.
Split the dwc3 core platform_driver callbacks and their implementation
and export the implementation, to make it possible to deterministically
instantiate the dwc3 core as part of the dwc3 glue drivers and to
allow flattening of the DeviceTree representation.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-3-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3 device suspend/resume callbacks were being triggered during system
suspend and resume even if the device was already runtime-suspended.
This is redundant for device mode because the suspend and resume routines
are essentially identical for system PM and runtime PM.
To prevent these unnecessary callbacks, indicate to the PM core that it
can safely leave the device in runtime suspend if it's already
runtime-suspended in device mode by returning a positive value in
prepare() callback. This optimization only applies to devices without
pinctrl, as pinctrl has distinct logic tied to system suspend/resume.
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250312223434.3071598-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow for the DWC3 host driver to pass along XHCI property that defines
how many interrupters to allocate. This is in relation for the number of
event rings that can be potentially used by other processors within the
system.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-7-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After phy initialization, some phy operations can only be executed while
in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking
phy ops.
Previously the SUSPENDENABLE bits are only set after the controller
initialization, which may not happen right away if there's no gadget
driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits
only when there's mode switching (change in GCTL.PRTCAPDIR).
Fixes: 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init")
Cc: stable <stable@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/633aef0afee7d56d2316f7cc3e1b2a6d518a8cc9.1738280911.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, DWC3 driver attempts to acquire the USB power supply only
once during the probe. If the USB power supply is not ready at that
time, the driver simply ignores the failure and continues the probe,
leading to permanent non-functioning of the gadget vbus_draw callback.
Address this problem by delaying the dwc3 driver initialization until
the USB power supply is registered.
Fixes: 6f0764b5ad ("usb: dwc3: add a power supply for current control")
Cc: stable <stable@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250115044548.2701138-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the system begins to enter suspend mode, dwc3_suspend() is called
by PM suspend. There is a problem that if someone interrupt the system
suspend process between dwc3_suspend() and pm_suspend() of its parent
device, PM suspend will be canceled and attempt to resume suspended
devices so that dwc3_resume() will be called. However, dwc3 and its
parent device (like the power domain or glue driver) may already be
suspended by runtime PM in fact. If this sutiation happened, the
pm_runtime_set_active() in dwc3_resume() will return an error since
parent device was suspended. This can lead to unexpected behavior if
DWC3 proceeds to execute dwc3_resume_common().
EX.
RPM suspend: ... -> dwc3_runtime_suspend()
-> rpm_suspend() of parent device
...
PM suspend: ... -> dwc3_suspend() -> pm_suspend of parent device
^ interrupt, so resume suspended device
... <- dwc3_resume() <-/
^ pm_runtime_set_active() returns error
To prevent the problem, this commit will skip dwc3_resume_common() and
return the error if pm_runtime_set_active() fails.
Fixes: 68c26fe581 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable <stable@kernel.org>
Signed-off-by: Ray Chi <raychi@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250106082240.3822059-1-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STAR 9001346572 addresses a USB 2.0 endpoint blocking issue in host mode
for controller versions DWC_usb31 1.70a and 1.80a. This issue affects
devices on both high-speed and full-speed bus instances. When all
endpoint caches are filled and a single active endpoint receives
continuous NAK responses, data transfers to other endpoints may get
blocked.
To resolve this, for controller versions DWC_usb31 1.70a and 1.80a, the
GUCTL3 bit[16] (USB2.0 Internal Retry Disable) is set to 1. This bit
disables the USB2.0 internal retry feature and ensures proper eviction
handling in the host controller endpoind cache. The GUCTL3[16] register
function is available only from DWC_usb31 version 1.70a.
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241129173422.20063-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.13-rc1.
Overall, a pretty slow development cycle, the majority of the work going
into the debugfs interface for the thunderbolt (i.e. USB4) code, to help
with debugging the myrad ways that hardware vendors get their interfaces
messed up. Other than that, here's the highlights:
- thunderbolt changes and additions to debugfs interfaces
- lots of device tree updates for new and old hardware
- UVC configfs gadget updates and new apis for features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- typec driver updates and fixes
- lots of other small updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lBqA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynTXQCfSs0ldBqZoINU/22q8BUg7ybb+pcAoL5EbbEm
b2igfp6YIEWAtUkactmO
=gwwq
-----END PGP SIGNATURE-----
Merge tag 'usb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.13-rc1.
Overall, a pretty slow development cycle, the majority of the work
going into the debugfs interface for the thunderbolt (i.e. USB4) code,
to help with debugging the myrad ways that hardware vendors get their
interfaces messed up. Other than that, here's the highlights:
- thunderbolt changes and additions to debugfs interfaces
- lots of device tree updates for new and old hardware
- UVC configfs gadget updates and new apis for features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- typec driver updates and fixes
- lots of other small updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: typec: tcpm: Add support for sink-bc12-completion-time-ms DT property
dt-bindings: usb: maxim,max33359: add usage of sink bc12 time property
dt-bindings: connector: Add time property for Sink BC12 detection completion
usb: dwc3: gadget: Remove dwc3_request->needs_extra_trb
usb: dwc3: gadget: Cleanup SG handling
usb: dwc3: gadget: Fix looping of queued SG entries
usb: dwc3: gadget: Fix checking for number of TRBs left
usb: dwc3: ep0: Don't clear ep0 DWC3_EP_TRANSFER_STARTED
Revert "usb: gadget: composite: fix OS descriptors w_value logic"
usb: ehci-spear: fix call balance of sehci clk handling routines
USB: make to_usb_device_driver() use container_of_const()
USB: make to_usb_driver() use container_of_const()
USB: properly lock dynamic id list when showing an id
USB: make single lock for all usb dynamic id lists
drivers/usb/storage: refactor min with min_t
drivers/usb/serial: refactor min with min_t
drivers/usb/musb: refactor min/max with min_t/max_t
drivers/usb/mon: refactor min with min_t
drivers/usb/misc: refactor min with min_t
drivers/usb/host: refactor min/max with min_t/max_t
...
Currently if the maximum-speed is set to Super Speed for a 3.1 Gen2
capable controller, the FORCE_GEN1 bit of LLUCTL register is set only
for one SuperSpeed port (or the first port) present. Modify the logic
to set the FORCE_GEN1 bit for all ports if speed is being limited to
Gen-1.
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112182018.199392-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device was already runtime suspended then during system suspend
we cannot access the device registers else it will crash.
Also we cannot access any registers after dwc3_core_exit() on some
platforms so move the dwc3_enable_susphy() call to the top.
Cc: stable@vger.kernel.org # v5.15+
Reported-by: William McVicker <willmcvicker@google.com>
Closes: https://lore.kernel.org/all/ZyVfcUuPq56R2m1Y@google.com
Fixes: 705e3ce37b ("usb: dwc3: core: Fix system suspend on TI AM62 platforms")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241104-am62-lpm-usb-fix-v1-1-e93df73a4f0d@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of (of|device)_property_read_bool() for non-boolean properties
is deprecated in favor of of_property_present() when testing for
property presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241104190820.277702-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init"),
system suspend is broken on AM62 TI platforms.
Before that commit, both DWC3_GUSB3PIPECTL_SUSPHY and DWC3_GUSB2PHYCFG_SUSPHY
bits (hence forth called 2 SUSPHY bits) were being set during core
initialization and even during core re-initialization after a system
suspend/resume.
These bits are required to be set for system suspend/resume to work correctly
on AM62 platforms.
Since that commit, the 2 SUSPHY bits are not set for DEVICE/OTG mode if gadget
driver is not loaded and started.
For Host mode, the 2 SUSPHY bits are set before the first system suspend but
get cleared at system resume during core re-init and are never set again.
This patch resovles these two issues by ensuring the 2 SUSPHY bits are set
before system suspend and restored to the original state during system resume.
Cc: stable@vger.kernel.org # v6.9+
Fixes: 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init")
Link: https://lore.kernel.org/all/1519dbe7-73b6-4afc-bfe3-23f4f75d772f@kernel.org/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20241011-am62-lpm-usb-v3-1-562d445625b5@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses an issue where events were being processed when
the controller was in a halted state. To fix this issue by stop
processing the events as the event count was considered stale or
invalid when the controller was halted.
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Cc: stable@kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240916231813.206-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc3_resume_common() returns an error, runtime pm is left in
suspended and disabled state in dwc3_resume(). Since the device
is suspended, its parent devices (like the power domain or glue
driver) could also be suspended and may have released resources
that dwc requires. Consequently, calling dwc3_suspend_common() in
this situation could result in attempts to access unclocked or
unpowered registers.
To prevent these problems, runtime PM should always be re-enabled,
even after failed resume attempts. This ensures that
dwc3_suspend_common() is skipped in such cases.
Fixes: 68c26fe581 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable@vger.kernel.org
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240913232145.3507723-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/usb to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240924084329.53094-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed some confusing typos that were currently identified with codespell,
the details are as follows:
-in the code comments:
drivers/usb/dwc3/core.c:1406: feild ==> field
drivers/usb/dwc3/core.h:84: boundries ==> boundaries
drivers/usb/dwc3/ep0.c:148: issueing ==> issuing
drivers/usb/dwc3/host.c:38: temperary ==> temporarily
Also fixed a syntax problem in the comments.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Link: https://lore.kernel.org/r/20240930022526.7255-1-shenlichuan@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix addresses STAR 9001285599, which only affects DWC_usb3 version
3.20a. The timer value for PM_LC_TIMER in DWC_usb3 3.20a for the Link
ECN changes is incorrect. If the PM TIMER ECN is enabled via GUCTL2[19],
the link compliance test (TD7.21) may fail. If the ECN is not enabled
(GUCTL2[19] = 0), the controller will use the old timer value (5us),
which is still acceptable for the link compliance test. Therefore, clear
GUCTL2[19] to pass the USB link compliance test: TD 7.21.
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240829094502.26502-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses an issue where the USB core could access an
invalid event buffer address during runtime suspend, potentially causing
SMMU faults and other memory issues in Exynos platforms. The problem
arises from the following sequence.
1. In dwc3_gadget_suspend, there is a chance of a timeout when
moving the USB core to the halt state after clearing the
run/stop bit by software.
2. In dwc3_core_exit, the event buffer is cleared regardless of
the USB core's status, which may lead to an SMMU faults and
other memory issues. if the USB core tries to access the event
buffer address.
To prevent this hardware quirk on Exynos platforms, this commit ensures
that the event buffer address is not cleared by software when the USB
core is active during runtime suspend by checking its status before
clearing the buffer address.
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240815064836.1491-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GSBUSCFG0 register bits [31:16] are used to configure the cache type
settings of the descriptor and data write/read transfers (Cacheable,
Bufferable/Posted). When CCI is enabled in the design, DWC3 core GSBUSCFG0
cache bits must be updated to support CCI enabled transfers in USB.
To program GSBUSCFG0 cache bits create a software node property
in AMD-xilinx dwc3 glue driver and pass it to dwc3 core. The core
then reads this property value and configures it in dwc3_core_init()
sequence.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1720548651-726412-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3_enable_susphy() applies to all available ports. After the
introduction of multi-port in dwc3, we now know the number of ports. Go
through the phy suspend registers of each port to enable/disable phy
suspend in dwc3_enable_susphy().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/31e18192c607dff0a7e5ca139dd5737d2224122a.1719879346.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a workaround for STAR 4846132, which only affects
DWC_usb31 version2.00a operating in host mode.
There is a problem in DWC_usb31 version 2.00a operating
in host mode that would cause a CSR read timeout When CSR
read coincides with RAM Clock Gating Entry. By disable
Clock Gating, sacrificing power consumption for normal
operation.
Cc: stable <stable@kernel.org> # 5.10.x: 1e43c86d: usb: dwc3: core: Add DWC31 version 2.00a controller
Signed-off-by: Jos Wang <joswang@lenovo.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240619114529.3441-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When config CONFIG_USB_DWC3_DUAL_ROLE is selected, and trigger system
to enter suspend status with below command:
echo mem > /sys/power/state
There will be a deadlock issue occurring. Detailed invoking path as
below:
dwc3_suspend_common()
spin_lock_irqsave(&dwc->lock, flags); <-- 1st
dwc3_gadget_suspend(dwc);
dwc3_gadget_soft_disconnect(dwc);
spin_lock_irqsave(&dwc->lock, flags); <-- 2nd
This issue is exposed by commit c7ebd8149e ("usb: dwc3: gadget: Fix
NULL pointer dereference in dwc3_gadget_suspend") that removes the code
of checking whether dwc->gadget_driver is NULL or not. It causes the
following code is executed and deadlock occurs when trying to get the
spinlock. In fact, the root cause is the commit 5265397f9442("usb: dwc3:
Remove DWC3 locking during gadget suspend/resume") that forgot to remove
the lock of otg mode. So, remove the redundant lock of otg mode during
gadget suspend/resume.
Fixes: 5265397f94 ("usb: dwc3: Remove DWC3 locking during gadget suspend/resume")
Cc: Xu Yang <xu.yang_2@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240618031918.2585799-1-Meng.Li@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmY39LkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGaB8H+wWcwT1O7K2SQx1a
sHDYJSXfbjgShS7Wt+gbDNvhGJqG/5FkpHyBmBKUdElZs8QMf21GAbIfJvzcNThA
g+FakIMjfhNH/dr6TJXHWbb2NZV67exDbbuaQDyMhNhIZqil4BH/OEPbLYIdquvm
/HDGFB/whVoHVC+Ug8esEOL3Uy+rizBDlsT/K4ZgpOC3TuUmlRpptSVACwjcCGXM
PFKyyTIr0ZnKcz3+4yTEtpDFm6e/ujxMwM66GBCgmPaZ3lJp5ruY3kGpBTmSyoqV
Rh3CQlIhBo8gwlAx/yQXfxEZomhxT6DfRpc6s/1W0J1UZN/j2pYy056OYyckG32c
uQ9ujxQ=
=M0wP
-----END PGP SIGNATURE-----
Merge 6.9-rc7 into usb-next
We want the USB fixes in here as well, and resolve a merge conflict in
drivers/usb/dwc3/core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent commit introduced support for reading Multiport PHYs and
while doing so iterated over an integer variable which runs from
[0-254] in the worst case scenario. But S390 compiler treats it as a
warning and complains that the integer write to string can go to 11
characters. Fix this by modifying iterator variable to u8.
Suggested-by: Johan Hovold <johan@kernel.org>
Fixes: 30a46746ca ("usb: dwc3: core: Refactor PHY logic to support Multiport Controller")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404241215.Mib19Cu7-lkp@intel.com/
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240426050512.57384-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the DWC3 driver supports only single port controller
which requires at least one HS PHY and at most one SS PHY.
But the DWC3 USB controller can be connected to multiple ports and
each port can have their own PHYs. Each port of the multiport
controller can either be HS+SS capable or HS only capable
Proper quantification of them is required to modify GUSB2PHYCFG
and GUSB3PIPECTL registers appropriately.
DWC3 multiport controllers are capable to service at most 15 High Speed
PHYs and 4 Supser Speed PHYs. Add support for detecting, obtaining and
configuring PHYs supported by a multiport controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-5-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some SoC's like SA8295P where the tertiary controller is host-only
capable, GEVTADDRHI/LO, GEVTSIZ, GEVTCOUNT registers are not accessible.
Trying to access them leads to a crash.
For DRD/Peripheral supported controllers, event buffer setup is done
again in gadget_pullup. Skip setup or cleanup of event buffers if
controller is host-only capable.
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-4-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All DWC3 Multi Port controllers that exist today only support host mode.
Temporarily map XHCI address space for host-only controllers and parse
XHCI Extended Capabilities registers to read number of usb2 ports and
usb3 ports present on multiport controller. Each USB Port is at least HS
capable.
The port info for usb2 and usb3 phy are identified as num_usb2_ports
and num_usb3_ports and these are used as iterators for phy operations
and for modifying GUSB2PHYCFG/ GUSB3PIPECTL registers accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-3-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
