For the device SP, the firmware version is a 32-bit value where the
lower 20 bits represent the base version number. And the customized
firmware version populates the upper 12 bits with a specific
identification number.
For other devices AML 25G and 40G, the upper 12 bits of the firmware
version is always non-zero, and they have other naming conventions.
Only SP devices need to check this to tell if XPCS will work properly.
So the judgement of MAC type is added here.
And the original logic compared the entire 32-bit value against 0x20010,
which caused the outdated base firmwares bypass the version check
without a warning. Apply a mask 0xfffff to isolate the lower 20 bits for
an accurate base version comparison.
Fixes: ab928c24e6 ("net: txgbe: add FW version warning")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/C787AA5C07598B13+20260422071837.372731-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge in late fixes in preparation for the net-next PR.
Conflicts:
include/net/sch_generic.h
a6bd339dbb ("net_sched: fix skb memory leak in deferred qdisc drops")
ff2998f29f ("net: sched: introduce qdisc-specific drop reason tracing")
https://lore.kernel.org/adz0iX85FHMz0HdO@sirena.org.uk
drivers/net/ethernet/airoha/airoha_eth.c
1acdfbdb51 ("net: airoha: Fix VIP configuration for AN7583 SoC")
bf3471e6e6 ("net: airoha: Make flow control source port mapping dependent on nbq parameter")
Adjacent changes:
drivers/net/ethernet/airoha/airoha_ppe.c
f44218cd5e ("net: airoha: Reset PPE cpu port configuration in airoha_ppe_hw_init()")
7da62262ec ("inet: add ip_local_port_step_width sysctl to improve port usage distribution")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hardware statistics should be updated periodically in the watchdog to
prevent 32-bit registers from overflowing. This is also required for the
upcoming pause frame accounting logic, which relies on regular statistics
sampling.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20260407025616.33652-8-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When removing the device, timer_delete_sync(&wx->service_timer) is
called in .ndo_stop() after cancel_work_sync(&wx->service_task). This
may cause new work to be queued after device down.
Move unregister_netdev() before cancel_work_sync(), and use
timer_shutdown_sync() to prevent the timer from being re-armed.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20260407025616.33652-7-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since function ops wx->setup_tc() is set in txgbe and ngbe,
ethtool_ops.set_channels can be implemented in libwx to reduce
duplicated code.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20260407025616.33652-6-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the busy-wait loop using test_and_set_bit(WX_STATE_RESETTING)
with a proper per-device mutex to serialize reset operations.
The reset flag is reserved for other code paths (like watchdog), which
need tocheck if a reset is in process.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20260407025616.33652-5-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lists of struct property_entry are supposed to be terminated with an
empty property, this driver currently seems to be allocating exactly the
amount of entry used.
Change the struct definition to leave an extra element for all
property_entry.
Fixes: c3e382ad6d ("net: txgbe: Add software nodes to support phylink")
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20260405222013.5347-1-fabio.baltieri@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
For these two firmware mailbox commands, in txgbe_test_hostif() and
txgbe_set_phy_link_hostif(), there is no need to read data from the
buffer.
Under the current setting, OEM firmware will cause the driver to fail to
probe. Because OEM firmware returns more link information, with a larger
OEM structure txgbe_hic_ephy_getlink. However, the current driver does
not support the OEM function. So just fix it in the way that does not
involve reading the returned data.
Fixes: d84a3ff9aa ("net: txgbe: Restrict the use of mismatched FW versions")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/2914AB0BC6158DDA+20260119065935.6015-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Getting module EEPROM has been supported in TXGBE SP devices, since SFP
driver has already implemented it.
Now add support to read module EEPROM for AML devices. Towards this, add
a new firmware mailbox command to get the page data.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20251118080259.24676-6-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For QSFP modules, there is a possibility that the module cannot be
identified when read I2C immediately in .ndo_open. So just set the flag
WX_FLAG_NEED_MODULE_RESET and do it in the subtask, which always wait
200 ms to identify the module. And this change has no impact on the
original adaptation.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20251118080259.24676-5-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Support to identify QSFP modules for AML 40G devices. The definition of
GPIO pins follows the design of the QSFP modules, and TXGBE_GPIOBIT_4 is
used for module present.
Meanwhile, implement phylink in XLGMII mode by default, and get the link
state from MAC link.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20251118080259.24676-4-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
QSFP supported will be introduced for AML 40G devices, the code related
to identify various modules should be renamed to more appropriate names.
And struct txgbe_hic_i2c_read used to get module information is renamed
as struct txgbe_hic_get_module_info, because another SW-FW command to
read I2C will be added later.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20251118080259.24676-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
TX head write-back mode is supported on AML devices. When it is enabled,
the hardware no longer writes the descriptors DD one by one, but write
back pointer of completion descriptor to the head_wb address.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251023014538.12644-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
RX descriptor merge mode is supported on AML devices. When it is
enabled, the hardware process the RX descriptors in batches.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251023014538.12644-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The function txgbe_get_phy_link() is more appropriately named
txgbe_get_mac_link(), since it reads the link status from the MAC
register.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20251014061726.36660-4-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To adapt to new firmware for AML devices, the driver should send the
"SET_LINK_CMD" to the firmware only once when switching PHY interface
mode, and no longer needs to re-trigger PHY configuration based on the
RX signal interrupt (TXGBE_GPIOBIT_3).
In previous firmware versions, the PHY was configured only after receiving
"SET_LINK_CMD", and might remain incomplete if the RX signal was lost.
To handle this case, the driver used TXGBE_GPIOBIT_3 interrupt to resend
the command. This workaround is no longer necessary with the new firmware.
And the unknown link speed is permitted in the mailbox buffer.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20251014061726.36660-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recent firmware updates introduce additional fields in the mailbox message
to provide more information for identifying 40G and 100G QSFP modules.
To accommodate these new fields, expand the mailbox buffer size by 4 bytes.
Without this change, drivers built against the updated firmware cannot
properly identify modules due to mismatched mailbox message lengths.
The old firmware version that used the smaller mailbox buffer has never
been publicly released, so there are no backward-compatibility concerns.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251014061726.36660-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add ethtool ops for Rx flow hashing, query and set RSS indirection table
and hash key. Disable UDP RSS by default, and support to configure L4
header fields with TCP/UDP/SCTP for flow hasing.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250926023843.34340-4-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support to turn on/off adaptive RX/TX coalesce. When adaptive coalesce
is on, use DIM algorithm for a dynamic interrupt moderation.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250821023408.53472-5-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to hardware limitations of NGBE, queue IRQs can only be requested
on vector 0 to 7. When the number of queues is set to the maximum 8,
the PCI IRQ vectors are allocated from 0 to 8. The vector 0 is used by
MISC interrupt, and althrough the vector 8 is used by queue interrupt,
it is unable to receive packets. This will cause some packets to be
dropped when RSS is enabled and they are assigned to queue 8.
So revert the adjustment of the MISC IRQ location, to make it be the
last one in IRQ vectors.
Fixes: 937d46ecc5 ("net: wangxun: add ethtool_ops for channel number")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20250701063030.59340-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move the creating of irq_domain for MISC IRQ from .probe to .ndo_open,
and free it in .ndo_stop, to maintain consistency with the queue IRQs.
This it for subsequent adjustments to the IRQ vectors.
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250701063030.59340-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is a occasional problem that ping is failed between AML devices.
That is because the manual enablement of the security Tx path on the
hardware is missing, no matter what its previous state was.
Fixes: 6f8b4c01a8 ("net: txgbe: Implement PHYLINK for AML 25G/10G devices")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/5BDFB14C57D1C42A+20250626085153.86122-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Core
----
- Implement the Device Memory TCP transmit path, allowing zero-copy
data transmission on top of TCP from e.g. GPU memory to the wire.
- Move all the IPv6 routing tables management outside the RTNL scope,
under its own lock and RCU. The route control path is now 3x times
faster.
- Convert queue related netlink ops to instance lock, reducing
again the scope of the RTNL lock. This improves the control plane
scalability.
- Refactor the software crc32c implementation, removing unneeded
abstraction layers and improving significantly the related
micro-benchmarks.
- Optimize the GRO engine for UDP-tunneled traffic, for a 10%
performance improvement in related stream tests.
- Cover more per-CPU storage with local nested BH locking; this is a
prep work to remove the current per-CPU lock in local_bh_disable()
on PREMPT_RT.
- Introduce and use nlmsg_payload helper, combining buffer bounds
verification with accessing payload carried by netlink messages.
Netfilter
---------
- Rewrite the procfs conntrack table implementation, improving
considerably the dump performance. A lot of user-space tools
still use this interface.
- Implement support for wildcard netdevice in netdev basechain
and flowtables.
- Integrate conntrack information into nft trace infrastructure.
- Export set count and backend name to userspace, for better
introspection.
BPF
---
- BPF qdisc support: BPF-qdisc can be implemented with BPF struct_ops
programs and can be controlled in similar way to traditional qdiscs
using the "tc qdisc" command.
- Refactor the UDP socket iterator, addressing long standing issues
WRT duplicate hits or missed sockets.
Protocols
---------
- Improve TCP receive buffer auto-tuning and increase the default
upper bound for the receive buffer; overall this improves the single
flow maximum thoughput on 200Gbs link by over 60%.
- Add AFS GSSAPI security class to AF_RXRPC; it provides transport
security for connections to the AFS fileserver and VL server.
- Improve TCP multipath routing, so that the sources address always
matches the nexthop device.
- Introduce SO_PASSRIGHTS for AF_UNIX, to allow disabling SCM_RIGHTS,
and thus preventing DoS caused by passing around problematic FDs.
- Retire DCCP socket. DCCP only receives updates for bugs, and major
distros disable it by default. Its removal allows for better
organisation of TCP fields to reduce the number of cache lines hit
in the fast path.
- Extend TCP drop-reason support to cover PAWS checks.
Driver API
----------
- Reorganize PTP ioctl flag support to require an explicit opt-in for
the drivers, avoiding the problem of drivers not rejecting new
unsupported flags.
- Converted several device drivers to timestamping APIs.
- Introduce per-PHY ethtool dump helpers, improving the support for
dump operations targeting PHYs.
Tests and tooling
-----------------
- Add support for classic netlink in user space C codegen, so that
ynl-c can now read, create and modify links, routes addresses and
qdisc layer configuration.
- Add ynl sub-types for binary attributes, allowing ynl-c to output
known struct instead of raw binary data, clarifying the classic
netlink output.
- Extend MPTCP selftests to improve the code-coverage.
- Add tests for XDP tail adjustment in AF_XDP.
New hardware / drivers
----------------------
- OpenVPN virtual driver: offload OpenVPN data channels processing
to the kernel-space, increasing the data transfer throughput WRT
the user-space implementation.
- Renesas glue driver for the gigabit ethernet RZ/V2H(P) SoC.
- Broadcom asp-v3.0 ethernet driver.
- AMD Renoir ethernet device.
- ReakTek MT9888 2.5G ethernet PHY driver.
- Aeonsemi 10G C45 PHYs driver.
Drivers
-------
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- refactor the stearing table handling to reduce significantly
the amount of memory used
- add support for complex matches in H/W flow steering
- improve flow streeing error handling
- convert to netdev instance locking
- Intel (100G, ice, igb, ixgbe, idpf):
- ice: add switchdev support for LLDP traffic over VF
- ixgbe: add firmware manipulation and regions devlink support
- igb: introduce support for frame transmission premption
- igb: adds persistent NAPI configuration
- idpf: introduce RDMA support
- idpf: add initial PTP support
- Meta (fbnic):
- extend hardware stats coverage
- add devlink dev flash support
- Broadcom (bnxt):
- add support for RX-side device memory TCP
- Wangxun (txgbe):
- implement support for udp tunnel offload
- complete PTP and SRIOV support for AML 25G/10G devices
- Ethernet NICs embedded and virtual:
- Google (gve):
- add device memory TCP TX support
- Amazon (ena):
- support persistent per-NAPI config
- Airoha:
- add H/W support for L2 traffic offload
- add per flow stats for flow offloading
- RealTek (rtl8211): add support for WoL magic packet
- Synopsys (stmmac):
- dwmac-socfpga 1000BaseX support
- add Loongson-2K3000 support
- introduce support for hardware-accelerated VLAN stripping
- Broadcom (bcmgenet):
- expose more H/W stats
- Freescale (enetc, dpaa2-eth):
- enetc: add MAC filter, VLAN filter RSS and loopback support
- dpaa2-eth: convert to H/W timestamping APIs
- vxlan: convert FDB table to rhashtable, for better scalabilty
- veth: apply qdisc backpressure on full ring to reduce TX drops
- Ethernet switches:
- Microchip (kzZ88x3): add ETS scheduler support
- Ethernet PHYs:
- RealTek (rtl8211):
- add support for WoL magic packet
- add support for PHY LEDs
- CAN:
- Adds RZ/G3E CANFD support to the rcar_canfd driver.
- Preparatory work for CAN-XL support.
- Add self-tests framework with support for CAN physical interfaces.
- WiFi:
- mac80211:
- scan improvements with multi-link operation (MLO)
- Qualcomm (ath12k):
- enable AHB support for IPQ5332
- add monitor interface support to QCN9274
- add multi-link operation support to WCN7850
- add 802.11d scan offload support to WCN7850
- monitor mode for WCN7850, better 6 GHz regulatory
- Qualcomm (ath11k):
- restore hibernation support
- MediaTek (mt76):
- WiFi-7 improvements
- implement support for mt7990
- Intel (iwlwifi):
- enhanced multi-link single-radio (EMLSR) support on 5 GHz links
- rework device configuration
- RealTek (rtw88):
- improve throughput for RTL8814AU
- RealTek (rtw89):
- add multi-link operation support
- STA/P2P concurrency improvements
- support different SAR configs by antenna
- Bluetooth:
- introduce HCI Driver protocol
- btintel_pcie: do not generate coredump for diagnostic events
- btusb: add HCI Drv commands for configuring altsetting
- btusb: add RTL8851BE device 0x0bda:0xb850
- btusb: add new VID/PID 13d3/3584 for MT7922
- btusb: add new VID/PID 13d3/3630 and 13d3/3613 for MT7925
- btnxpuart: implement host-wakeup feature
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=t/Tz
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Implement the Device Memory TCP transmit path, allowing zero-copy
data transmission on top of TCP from e.g. GPU memory to the wire.
- Move all the IPv6 routing tables management outside the RTNL scope,
under its own lock and RCU. The route control path is now 3x times
faster.
- Convert queue related netlink ops to instance lock, reducing again
the scope of the RTNL lock. This improves the control plane
scalability.
- Refactor the software crc32c implementation, removing unneeded
abstraction layers and improving significantly the related
micro-benchmarks.
- Optimize the GRO engine for UDP-tunneled traffic, for a 10%
performance improvement in related stream tests.
- Cover more per-CPU storage with local nested BH locking; this is a
prep work to remove the current per-CPU lock in local_bh_disable()
on PREMPT_RT.
- Introduce and use nlmsg_payload helper, combining buffer bounds
verification with accessing payload carried by netlink messages.
Netfilter:
- Rewrite the procfs conntrack table implementation, improving
considerably the dump performance. A lot of user-space tools still
use this interface.
- Implement support for wildcard netdevice in netdev basechain and
flowtables.
- Integrate conntrack information into nft trace infrastructure.
- Export set count and backend name to userspace, for better
introspection.
BPF:
- BPF qdisc support: BPF-qdisc can be implemented with BPF struct_ops
programs and can be controlled in similar way to traditional qdiscs
using the "tc qdisc" command.
- Refactor the UDP socket iterator, addressing long standing issues
WRT duplicate hits or missed sockets.
Protocols:
- Improve TCP receive buffer auto-tuning and increase the default
upper bound for the receive buffer; overall this improves the
single flow maximum thoughput on 200Gbs link by over 60%.
- Add AFS GSSAPI security class to AF_RXRPC; it provides transport
security for connections to the AFS fileserver and VL server.
- Improve TCP multipath routing, so that the sources address always
matches the nexthop device.
- Introduce SO_PASSRIGHTS for AF_UNIX, to allow disabling SCM_RIGHTS,
and thus preventing DoS caused by passing around problematic FDs.
- Retire DCCP socket. DCCP only receives updates for bugs, and major
distros disable it by default. Its removal allows for better
organisation of TCP fields to reduce the number of cache lines hit
in the fast path.
- Extend TCP drop-reason support to cover PAWS checks.
Driver API:
- Reorganize PTP ioctl flag support to require an explicit opt-in for
the drivers, avoiding the problem of drivers not rejecting new
unsupported flags.
- Converted several device drivers to timestamping APIs.
- Introduce per-PHY ethtool dump helpers, improving the support for
dump operations targeting PHYs.
Tests and tooling:
- Add support for classic netlink in user space C codegen, so that
ynl-c can now read, create and modify links, routes addresses and
qdisc layer configuration.
- Add ynl sub-types for binary attributes, allowing ynl-c to output
known struct instead of raw binary data, clarifying the classic
netlink output.
- Extend MPTCP selftests to improve the code-coverage.
- Add tests for XDP tail adjustment in AF_XDP.
New hardware / drivers:
- OpenVPN virtual driver: offload OpenVPN data channels processing to
the kernel-space, increasing the data transfer throughput WRT the
user-space implementation.
- Renesas glue driver for the gigabit ethernet RZ/V2H(P) SoC.
- Broadcom asp-v3.0 ethernet driver.
- AMD Renoir ethernet device.
- ReakTek MT9888 2.5G ethernet PHY driver.
- Aeonsemi 10G C45 PHYs driver.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- refactor the steering table handling to significantly
reduce the amount of memory used
- add support for complex matches in H/W flow steering
- improve flow streeing error handling
- convert to netdev instance locking
- Intel (100G, ice, igb, ixgbe, idpf):
- ice: add switchdev support for LLDP traffic over VF
- ixgbe: add firmware manipulation and regions devlink support
- igb: introduce support for frame transmission premption
- igb: adds persistent NAPI configuration
- idpf: introduce RDMA support
- idpf: add initial PTP support
- Meta (fbnic):
- extend hardware stats coverage
- add devlink dev flash support
- Broadcom (bnxt):
- add support for RX-side device memory TCP
- Wangxun (txgbe):
- implement support for udp tunnel offload
- complete PTP and SRIOV support for AML 25G/10G devices
- Ethernet NICs embedded and virtual:
- Google (gve):
- add device memory TCP TX support
- Amazon (ena):
- support persistent per-NAPI config
- Airoha:
- add H/W support for L2 traffic offload
- add per flow stats for flow offloading
- RealTek (rtl8211): add support for WoL magic packet
- Synopsys (stmmac):
- dwmac-socfpga 1000BaseX support
- add Loongson-2K3000 support
- introduce support for hardware-accelerated VLAN stripping
- Broadcom (bcmgenet):
- expose more H/W stats
- Freescale (enetc, dpaa2-eth):
- enetc: add MAC filter, VLAN filter RSS and loopback support
- dpaa2-eth: convert to H/W timestamping APIs
- vxlan: convert FDB table to rhashtable, for better scalabilty
- veth: apply qdisc backpressure on full ring to reduce TX drops
- Ethernet switches:
- Microchip (kzZ88x3): add ETS scheduler support
- Ethernet PHYs:
- RealTek (rtl8211):
- add support for WoL magic packet
- add support for PHY LEDs
- CAN:
- Adds RZ/G3E CANFD support to the rcar_canfd driver.
- Preparatory work for CAN-XL support.
- Add self-tests framework with support for CAN physical interfaces.
- WiFi:
- mac80211:
- scan improvements with multi-link operation (MLO)
- Qualcomm (ath12k):
- enable AHB support for IPQ5332
- add monitor interface support to QCN9274
- add multi-link operation support to WCN7850
- add 802.11d scan offload support to WCN7850
- monitor mode for WCN7850, better 6 GHz regulatory
- Qualcomm (ath11k):
- restore hibernation support
- MediaTek (mt76):
- WiFi-7 improvements
- implement support for mt7990
- Intel (iwlwifi):
- enhanced multi-link single-radio (EMLSR) support on 5 GHz links
- rework device configuration
- RealTek (rtw88):
- improve throughput for RTL8814AU
- RealTek (rtw89):
- add multi-link operation support
- STA/P2P concurrency improvements
- support different SAR configs by antenna
- Bluetooth:
- introduce HCI Driver protocol
- btintel_pcie: do not generate coredump for diagnostic events
- btusb: add HCI Drv commands for configuring altsetting
- btusb: add RTL8851BE device 0x0bda:0xb850
- btusb: add new VID/PID 13d3/3584 for MT7922
- btusb: add new VID/PID 13d3/3630 and 13d3/3613 for MT7925
- btnxpuart: implement host-wakeup feature"
* tag 'net-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1611 commits)
selftests/bpf: Fix bpf selftest build warning
selftests: netfilter: Fix skip of wildcard interface test
net: phy: mscc: Stop clearing the the UDPv4 checksum for L2 frames
net: openvswitch: Fix the dead loop of MPLS parse
calipso: Don't call calipso functions for AF_INET sk.
selftests/tc-testing: Add a test for HFSC eltree double add with reentrant enqueue behaviour on netem
net_sched: hfsc: Address reentrant enqueue adding class to eltree twice
octeontx2-pf: QOS: Refactor TC_HTB_LEAF_DEL_LAST callback
octeontx2-pf: QOS: Perform cache sync on send queue teardown
net: mana: Add support for Multi Vports on Bare metal
net: devmem: ncdevmem: remove unused variable
net: devmem: ksft: upgrade rx test to send 1K data
net: devmem: ksft: add 5 tuple FS support
net: devmem: ksft: add exit_wait to make rx test pass
net: devmem: ksft: add ipv4 support
net: devmem: preserve sockc_err
page_pool: fix ugly page_pool formatting
net: devmem: move list_add to net_devmem_bind_dmabuf.
selftests: netfilter: nft_queue.sh: include file transfer duration in log message
net: phy: mscc: Fix memory leak when using one step timestamping
...
When SR-IOV is enabled, the FDIR rule is supported to filter packets to
VFs. The action queue id is calculated as an absolute id.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/BE7EA355FDDAAA97+20250523080438.27968-2-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Consolidate on one set of functions for the interrupt domain code to
get rid of pointlessly duplicated code with only marginal different
semantics.
- Update the documentation accordingly and consolidate the coding style
of the irqdomain header.
-----BEGIN PGP SIGNATURE-----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=9nLp
-----END PGP SIGNATURE-----
Merge tag 'irq-cleanups-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq cleanups from Thomas Gleixner:
"A set of cleanups for the generic interrupt subsystem:
- Consolidate on one set of functions for the interrupt domain code
to get rid of pointlessly duplicated code with only marginal
different semantics.
- Update the documentation accordingly and consolidate the coding
style of the irqdomain header"
* tag 'irq-cleanups-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
irqdomain: Consolidate coding style
irqdomain: Fix kernel-doc and add it to Documentation
Documentation: irqdomain: Update it
Documentation: irq-domain.rst: Simple improvements
Documentation: irq/concepts: Minor improvements
Documentation: irq/concepts: Add commas and reflow
irqdomain: Improve kernel-docs of functions
irqdomain: Make struct irq_domain_info variables const
irqdomain: Use irq_domain_instantiate()'s return value as initializers
irqdomain: Drop irq_linear_revmap()
pinctrl: keembay: Switch to irq_find_mapping()
irqchip/armada-370-xp: Switch to irq_find_mapping()
gpu: ipu-v3: Switch to irq_find_mapping()
gpio: idt3243x: Switch to irq_find_mapping()
sh: Switch to irq_find_mapping()
powerpc: Switch to irq_find_mapping()
irqdomain: Drop irq_domain_add_*() functions
powerpc: Switch irq_domain_add_nomap() to use fwnode
thermal: Switch to irq_domain_create_linear()
soc: Switch to irq_domain_create_*()
...
Since .mac_link_up and .mac_link_down are changed for AML 25G/10G NICs,
the SR-IOV related function should be invoked in these new functions, to
bring VFs link up.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/BA8B302B7AAB6EA6+20250521064402.22348-10-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The new added mailbox commands require a new released firmware version.
Otherwise, a lot of logs "Unknown FW command" would be printed. And the
devices may not work properly. So add the test command in the probe
function.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/18283F17BE0FA335+20250521064402.22348-8-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For AML 25G/10G devices, some of the information returned from
phylink_ethtool_ksettings_get() is not correct, since there is a
fixed-link mode. So add additional corrections.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/C94BF867617C544D+20250521064402.22348-7-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver needs to handle GPIO interrupts to identify SFP module and
configure PHY by sending mailbox messages to firmware.
Since the SFP module needs to wait for ready to get information when it
is inserted, workqueue is added to handle delayed tasks. And each SW-FW
interaction takes time to wait, so they are processed in the workqueue
instead of IRQ handler function.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/399624AF221E8E28+20250521064402.22348-6-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is a new PHY attached to AML 25G/10G NIC, which is different from
SP 10G/1G NIC. But the PHY configuration is handed over to firmware, and
also I2C is controlled by firmware. So the different PHYLINK fixed-link
mode is added for these devices.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/987B973A5929CD48+20250521064402.22348-5-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For the following patches to support PHYLINK for AML 25G devices,
separate MAC type wx_mac_aml40 to maintain the driver of 40G devices.
Because 40G devices will complete support later, not now.
And this patch makes the 25G devices use some PHYLINK interfaces, but it
is not yet create PHYLINK and cannot be used on its own. It is just
preparation for the next patches.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/592B1A6920867D0C+20250521064402.22348-4-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Most of the different code that requires MAC type in the common library
is due to NGBE only supports a few queues and pools, unlike TXGBE, which
supports 128 queues and 64 pools. This difference accounts for most of
the hardware configuration differences in the driver code. So add a flag
bit "WX_FLAG_MULTI_64_FUNC" for them to clean-up the driver code.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/C731132E124D75E5+20250521064402.22348-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-28-jirislaby@kernel.org
In the new firmware version, the shadow ram reserves some space to store
I2C information, so the checksum calculation needs to skip this section.
Otherwise, the driver will fail to probe because the invalid EEPROM
checksum.
Fixes: 2e5af6b2ae ("net: txgbe: Add basic support for new AML devices")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1C6BF7A937237F5A+20250513021009.145708-2-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are wrong "#endif" comments in .h files need to be corrected.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For unknown reasons, sometimes the value of MISC interrupt is 0 in the
IRQ handle function. In this case, wx_intr_enable() is also should be
invoked to clear the interrupt. Otherwise, the next interrupt would
never be reported.
Fixes: a9843689e2 ("net: txgbe: add sriov function support")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/F4F708403CE7090B+20250512100652.139510-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement ndo_features_check to restrict Tx checksum offload flags, since
there are some inner layer length and protocols unsupported.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20250421022956.508018-3-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tunnel types VXLAN/VXLAN_GPE/GENEVE are supported for txgbe devices. The
hardware supports to set only one port for each tunnel type.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250421022956.508018-2-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When txgbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in txgbe_probe() function, the subsequent
error paths after txgbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when txgbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Fixes: 937d46ecc5 ("net: wangxun: add ethtool_ops for channel number")
Reported-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250415032910.13139-1-abdun.nihaal@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
