Starting with DPCD version 2.0 bits 6:3 of the DP_DSC_BITS_PER_PIXEL_INC
DPCD register contains the NativeYCbCr422_MAX_bpp_DELTA field, which can
be non-zero as opposed to earlier DPCD versions, hence decoding the
bit_per_pixel increment value at bits 2:0 in the same register requires
applying a mask, do so.
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Fixes: 0c2287c965 ("drm/display/dp: Add helper function to get DSC bpp precision")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250212161851.4007005-1-imre.deak@intel.com
Extended wake timeout request helps to give additional
time by reading the DPCD register through which sink requests the
minimal amount of time required to wake the sink up.
Source device shall keep retying the AUX tansaction till the
extended timeout that is being granted for LTTPRs from the
sink device.
--v2
-Add documentation [Dmitry]
Spec: DP v2.1 Section 3.6.12.3
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250122053358.1545039-3-suraj.kandpal@intel.com
If the hotplug detect of a display is low for longer than one second
(configurable through drm_dp_cec_unregister_delay), then the CEC adapter
is unregistered since we assume the display was disconnected. If the
HPD went low for less than one second, then we check if the properties
of the CEC adapter have changed, since that indicates that we actually
switch to new hardware and we have to unregister the old CEC device and
register a new one.
Unfortunately, the test for changed properties was written poorly, and
after a new CEC capability was added to the CEC core code the test always
returned true (i.e. the properties had changed).
As a result the CEC device was unregistered and re-registered for every
HPD toggle. If the CEC remote controller integration was also enabled
(CONFIG_MEDIA_CEC_RC was set), then the corresponding input device was
also unregistered and re-registered. As a result the input device in
/sys would keep incrementing its number, e.g.:
/sys/devices/pci0000:00/0000:00:08.1/0000:e7:00.0/rc/rc0/input20
Since short HPD toggles are common, the number could over time get into
the thousands.
While not a serious issue (i.e. nothing crashes), it is not intended
to work that way.
This patch changes the test so that it only checks for the single CEC
capability that can actually change, and it ignores any other
capabilities, so this is now safe as well if new caps are added in
the future.
With the changed test the bit under #ifndef CONFIG_MEDIA_CEC_RC can be
dropped as well, so that's a nice cleanup.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Farblos <farblos@vodafonemail.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 2c6d1fffa1 ("drm: add support for DisplayPort CEC-Tunneling-over-AUX")
Tested-by: Farblos <farblos@vodafonemail.de>
Link: https://patchwork.freedesktop.org/patch/msgid/361bb03d-1691-4e23-84da-0861ead5dbdc@xs4all.nl
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Avoid hardcoding the LSPCON settle timeout because it takes a longer
time on certain chips made by certain vendors. Use the function that
already exists to determine the timeout.
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Giedrius Statkevičius <giedriuswork@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241017075725.207384-1-giedriuswork@gmail.com
Acked-by: Simona Vetter <simona.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add a helper drm_dp_mst_get_ufp_num_at_lct_from_rad() to extract the up
facing port number at specific link count from the RAD. Use the added
helper in drm_dp_mst_rad_to_str() & drm_dp_get_mst_branch_device() to
unify the implementation.
V2:
- Adjust the code format (Lyude)
V3:
- Adjust parameter "rad" of drm_dp_mst_get_ufp_num_at_lct_from_rad() to
be constant (Kernel test robot)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
[fixed commit message typo]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113091100.3314533-3-Wayne.Lin@amd.com
[Why]
The RAD of sideband message printed today is incorrect.
For RAD stored within MST branch
- If MST branch LCT is 1, it's RAD array is untouched and remained as 0.
- If MST branch LCT is larger than 1, use nibble to store the up facing
port number in cascaded sequence as illustrated below:
u8 RAD[0] = (LCT_2_UFP << 4) | LCT_3_UFP
RAD[1] = (LCT_4_UFP << 4) | LCT_5_UFP
...
In drm_dp_mst_rad_to_str(), it wrongly to use BIT_MASK(4) to fetch the port
number of one nibble.
[How]
Adjust the code by:
- RAD array items are valuable only for LCT >= 1.
- Use 0xF as the mask to replace BIT_MASK(4)
V2:
- Document how RAD is constructed (Imre)
V3:
- Adjust the comment for rad[] so kdoc formats it properly (Lyude)
Fixes: 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing + selftests")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113091100.3314533-2-Wayne.Lin@amd.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmeNkBEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGgN4IAIEa4TrwIPP0cI4h
iLI7rXcQaQplFlEGcmLutzItlf2YnoSoIa7fJoThJwKZIcz5o76sqtbTvQebZGsO
SRmthEixpFdJK//5fQR1OZaSsMAifH2kQrEjvQqF7OxwvVOOAHZ7bUuyOvrTRFE8
Su6kUXjmtN4O2oBEVgPKiStjd2sIqT8+Y67WjGwbDY7cU7m0qN4aBegPg5wrHQWm
edIBWN53dv/5R197qntCxaTGG+OsiFHr6LMfg6tLhq8Pw+hFGAcdgcUZ2YeCbmw8
noN0ukiaOewRgYmZI8oj8x6+zncNR/SWFNgAMxnLvK8o5oHx0R/0CtgNZSi7ocn3
WIm9hzg=
=m02S
-----END PGP SIGNATURE-----
Merge v6.13 into drm-next
A regression was caused by commit e4b5ccd392 ("drm/v3d: Ensure job
pointer is set to NULL after job completion"), but this commit is not
yet in next-fixes, fast-forward it.
Note that this recreates Linus merge in 96c84703f1 ("Merge tag
'drm-next-2025-01-17' of https://gitlab.freedesktop.org/drm/kernel")
because I didn't want to backmerge a random point in the merge window.
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
core:
- device memory cgroup controller added
- Remove driver date from drm_driver
- Add drm_printer based hex dumper
- drm memory stats docs update
- scheduler documentation improvements
new driver:
- amdxdna - Ryzen AI NPU support
connector:
- add a mutex to protect ELD
- make connector setup two-step
panels:
- Introduce backlight quirks infrastructure
- New panels: KDB KD116N2130B12, Tianma TM070JDHG34-00,
- Multi-Inno Technology MI1010Z1T-1CP11
bridge:
- ti-sn65dsi83: Add ti,lvds-vod-swing optional properties
- Provide default implementation of atomic_check for HDMI bridges
- it605: HDCP improvements, MCCS Support
xe:
- make OA buffer size configurable
- GuC capture fixes
- add ufence and g2h flushes
- restore system memory GGTT mappings
- ioctl fixes
- SRIOV PF scheduling priority
- allow fault injection
- lots of improvements/refactors
- Enable GuC's WA_DUAL_QUEUE for newer platforms
- IRQ related fixes and improvements
i915:
- More accurate engine busyness metrics with GuC submission
- Ensure partial BO segment offset never exceeds allowed max
- Flush GuC CT receive tasklet during reset preparation
- Some DG2 refactor to fix DG2 bugs when operating with certain CPUs
- Fix DG1 power gate sequence
- Enabling uncompressed 128b/132b UHBR SST
- Handle hdmi connector init failures, and no HDMI/DP cases
- More robust engine resets on Haswell and older
i915/xe display:
- HDCP fixes for Xe3Lpd
- New GSC FW ARL-H/ARL-U
- support 3 VDSC engines 12 slices
- MBUS joining sanitisation
- reconcile i915/xe display power mgmt
- Xe3Lpd fixes
- UHBR rates for Thunderbolt
amdgpu:
- DRM panic support
- track BO memory stats at runtime
- Fix max surface handling in DC
- Cleaner shader support for gfx10.3 dGPUs
- fix drm buddy trim handling
- SDMA engine reset updates
- Fix doorbell ttm cleanup
- RAS updates
- ISP updates
- SDMA queue reset support
- Rework DPM powergating interfaces
- Documentation updates and cleanups
- DCN 3.5 updates
- Use a pm notifier to more gracefully handle VRAM eviction on suspend or hibernate
- Add debugfs interfaces for forcing scheduling to specific engine instances
- GG 9.5 updates
- IH 4.4 updates
- Make missing optional firmware less noisy
- PSP 13.x updates
- SMU 13.x updates
- VCN 5.x updates
- JPEG 5.x updates
- GC 12.x updates
- DC FAMS updates
amdkfd:
- GG 9.5 updates
- Logging improvements
- Shader debugger fixes
- Trap handler cleanup
- Cleanup includes
- Eviction fence wq fix
msm:
- MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
- DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two SSPPs for a single plane)
- added CWB hardware blocks support
- DSI:
- added SM6150 (aka QCS615) support
- GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
rcar-du:
- Add r8a779h0 Support
ivpu:
- Fix qemu crash when using passthrough
nouveau:
- expose GSP-RM logging buffers via debugfs
panfrost:
- Add MT8188 Mali-G57 MC3 support
rockchip:
- Gamma LUT support
hisilicon:
- new HIBMC support
virtio-gpu:
- convert to helpers
- add prime support for scanout buffers
v3d:
- Add DRM_IOCTL_V3D_PERFMON_SET_GLOBAL
vc4:
- Add support for BCM2712
vkms:
- line-per-line compositing algorithm to improve performance
zynqmp:
- Add DP audio support
mediatek:
- dp: Add sdp path reset
- dp: Support flexible length of DP calibration data
etnaviv:
- add fdinfo memory support
- add explicit reset handling
-----BEGIN PGP SIGNATURE-----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=5FIc
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-01-17' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"There are two external interactions of note, the msm tree pull in some
opp tree, hopefully the opp tree arrives from the same git tree
however it normally does.
There is also a new cgroup controller for device memory, that is used
by drm, so is merging through my tree. This will hopefully help open
up gpu cgroup usage a bit more and move us forward.
There is a new accelerator driver for the AMD XDNA Ryzen AI NPUs.
Then the usual xe/amdgpu/i915/msm leaders and lots of changes and
refactors across the board:
core:
- device memory cgroup controller added
- Remove driver date from drm_driver
- Add drm_printer based hex dumper
- drm memory stats docs update
- scheduler documentation improvements
new driver:
- amdxdna - Ryzen AI NPU support
connector:
- add a mutex to protect ELD
- make connector setup two-step
panels:
- Introduce backlight quirks infrastructure
- New panels: KDB KD116N2130B12, Tianma TM070JDHG34-00,
- Multi-Inno Technology MI1010Z1T-1CP11
bridge:
- ti-sn65dsi83: Add ti,lvds-vod-swing optional properties
- Provide default implementation of atomic_check for HDMI bridges
- it605: HDCP improvements, MCCS Support
xe:
- make OA buffer size configurable
- GuC capture fixes
- add ufence and g2h flushes
- restore system memory GGTT mappings
- ioctl fixes
- SRIOV PF scheduling priority
- allow fault injection
- lots of improvements/refactors
- Enable GuC's WA_DUAL_QUEUE for newer platforms
- IRQ related fixes and improvements
i915:
- More accurate engine busyness metrics with GuC submission
- Ensure partial BO segment offset never exceeds allowed max
- Flush GuC CT receive tasklet during reset preparation
- Some DG2 refactor to fix DG2 bugs when operating with certain CPUs
- Fix DG1 power gate sequence
- Enabling uncompressed 128b/132b UHBR SST
- Handle hdmi connector init failures, and no HDMI/DP cases
- More robust engine resets on Haswell and older
i915/xe display:
- HDCP fixes for Xe3Lpd
- New GSC FW ARL-H/ARL-U
- support 3 VDSC engines 12 slices
- MBUS joining sanitisation
- reconcile i915/xe display power mgmt
- Xe3Lpd fixes
- UHBR rates for Thunderbolt
amdgpu:
- DRM panic support
- track BO memory stats at runtime
- Fix max surface handling in DC
- Cleaner shader support for gfx10.3 dGPUs
- fix drm buddy trim handling
- SDMA engine reset updates
- Fix doorbell ttm cleanup
- RAS updates
- ISP updates
- SDMA queue reset support
- Rework DPM powergating interfaces
- Documentation updates and cleanups
- DCN 3.5 updates
- Use a pm notifier to more gracefully handle VRAM eviction on
suspend or hibernate
- Add debugfs interfaces for forcing scheduling to specific engine
instances
- GG 9.5 updates
- IH 4.4 updates
- Make missing optional firmware less noisy
- PSP 13.x updates
- SMU 13.x updates
- VCN 5.x updates
- JPEG 5.x updates
- GC 12.x updates
- DC FAMS updates
amdkfd:
- GG 9.5 updates
- Logging improvements
- Shader debugger fixes
- Trap handler cleanup
- Cleanup includes
- Eviction fence wq fix
msm:
- MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
- DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two
SSPPs for a single plane)
- added CWB hardware blocks support
- DSI:
- added SM6150 (aka QCS615) support
- GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
rcar-du:
- Add r8a779h0 Support
ivpu:
- Fix qemu crash when using passthrough
nouveau:
- expose GSP-RM logging buffers via debugfs
panfrost:
- Add MT8188 Mali-G57 MC3 support
rockchip:
- Gamma LUT support
hisilicon:
- new HIBMC support
virtio-gpu:
- convert to helpers
- add prime support for scanout buffers
v3d:
- Add DRM_IOCTL_V3D_PERFMON_SET_GLOBAL
vc4:
- Add support for BCM2712
vkms:
- line-per-line compositing algorithm to improve performance
zynqmp:
- Add DP audio support
mediatek:
- dp: Add sdp path reset
- dp: Support flexible length of DP calibration data
etnaviv:
- add fdinfo memory support
- add explicit reset handling"
* tag 'drm-next-2025-01-17' of https://gitlab.freedesktop.org/drm/kernel: (1070 commits)
drm/bridge: fix documentation for the hdmi_audio_prepare() callback
doc/cgroup: Fix title underline length
drm/doc: Include new drm-compute documentation
cgroup/dmem: Fix parameters documentation
cgroup/dmem: Select PAGE_COUNTER
kernel/cgroup: Remove the unused variable climit
drm/display: hdmi: Do not read EDID on disconnected connectors
drm/tests: hdmi: Add connector disablement test
drm/connector: hdmi: Do atomic check when necessary
drm/amd/display: 3.2.316
drm/amd/display: avoid reset DTBCLK at clock init
drm/amd/display: improve dpia pre-train
drm/amd/display: Apply DML21 Patches
drm/amd/display: Use HW lock mgr for PSR1
drm/amd/display: Revised for Replay Pseudo vblank control
drm/amd/display: Add a new flag for replay low hz
drm/amd/display: Remove unused read_ono_state function from Hwss module
drm/amd/display: Do not elevate mem_type change to full update
drm/amd/display: Do not wait for PSR disable on vbl enable
drm/amd/display: Remove unnecessary eDP power down
...
The recently introduced hotplug event handler in the HDMI Connector
framework attempts to unconditionally read the EDID data, leading to a
bunch of non-harmful, yet quite annoying DDC/I2C related errors being
reported.
Ensure the operation is done only for connectors having the status
connected or unknown. Additionally, perform an explicit reset of the
connector information when dealing with a disconnected status.
Fixes: ab716b74dc ("drm/display/hdmi: implement hotplug functions")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113-hdmi-conn-edid-read-fix-v2-1-d2a0438a44ab@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
It's ok to pass atomic check successfully if an atomic commit tries to
disable the display pipeline which the connector belongs to. That is,
when the crtc or the best_encoder pointers in struct drm_connector_state
are NULL, drm_atomic_helper_connector_hdmi_check() should return 0.
Without the check against the NULL pointers, drm_default_rgb_quant_range()
called by drm_atomic_helper_connector_hdmi_check() would dereference
the NULL pointer to_match in drm_match_cea_mode().
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
drm_default_rgb_quant_range+0x0/0x4c (P)
drm_bridge_connector_atomic_check+0x20/0x2c
drm_atomic_helper_check_modeset+0x488/0xc78
drm_atomic_helper_check+0x20/0xa4
drm_atomic_check_only+0x4b8/0x984
drm_atomic_commit+0x48/0xc4
drm_framebuffer_remove+0x44c/0x530
drm_mode_rmfb_work_fn+0x7c/0xa0
process_one_work+0x150/0x294
worker_thread+0x2dc/0x3dc
kthread+0x130/0x204
ret_from_fork+0x10/0x20
Fixes: 8ec116ff21 ("drm/display: bridge_connector: provide atomic_check for HDMI bridges")
Fixes: 84e541b1e5 ("drm/sun4i: use drm_atomic_helper_connector_hdmi_check()")
Fixes: 65548c8ff0 ("drm/rockchip: inno_hdmi: Switch to HDMI connector")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110084821.3239518-2-victor.liu@nxp.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The case of having an HDMI bridge in the pipeline which advertises
YUV420 capability via its ->supported_formats and a non-HDMI one that
didn't enable ->ycbcr_420_allowed, is incorrectly handled because
supported_formats is passed as is to the helper initializing the HDMI
connector.
Ensure HDMI_COLORSPACE_YUV420 is removed from the bitmask passed to
drmm_connector_hdmi_init() when connector's ->ycbcr_420_allowed flag
ends up not being set.
Fixes: 3ced1c6875 ("drm/display: bridge_connector: handle ycbcr_420_allowed")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-bridge-conn-fmt-prio-v4-2-a9ceb5671379@collabora.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmd7BBQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGfEEH/3oyTWmD5DPX2lLp
SujyKrEs6bfMQTKKYHzuy8OvzDXkBpZiKXIsCgjF5sXwQVgB7KPfJwgjt5xLo3F3
NTehLGwII7bM8mSq3wHDMeNkyBle4VYA9XOR8tXj21j7aRt9S4U/vtXiYeD9BWhC
Y1p+1FXKfZf7TjNpu8lIl+zLjSFDjYwM8h72dIuHnrYeuFL88fnWwoNP/MFkk5Kk
ce3ol3EtFe/M4GbVOm7KfzEkbsEE6ES60O0suxwYDn+71EA6ExVHFBKqpQvfj71/
ynxWYIwMoiCZWtJ+ali1g/ms0OxG+ivH8+xasBYTcDICZMe/XGX5Yx+Wm5DH5/Ev
pGMyvbI=
=yrc7
-----END PGP SIGNATURE-----
Merge tag 'v6.13-rc6' into drm-next
This backmerges Linux 6.13-rc6 this is need for the newer pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Some DG2 refactor to fix DG2 bugs when operating with certain CPUs (Raag)
- Use hw support for min/interim ddb allocation for async flip (Vinod)
- More general code refactor to allow full display separation (Jani)
- Expose dsc sink max slice count via debugfs (Swati)
- Fix C10 pll programming sequence (Suraj)
- Fix DG1 power gate sequence (Rodrigo)
- Use preemption timeout on selftest cleanup (Janusz)
- DP DSC related fixes (Ankit)
- Fix HDCP compliance test (Suraj)
- Clean and Optimise mtl_ddi_prepare_link_retrain (Suraj)
- Adjust Added Wake Time with PKG_C_LATENCY (Animesh)
- Enabling uncompressed 128b/132b UHBR SST (Jani)
- Handle hdmi connector init failures, and no HDMI/DP cases (Jani)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmd9flgACgkQ+mJfZA7r
E8qSKAf9FoiRZD5dJVQ60wNEszj3Ub647+32sl2jA7jb5twoUve3ZreJvTCKUMfd
jtd+FIJtB9JLX9LwK9v8TBkkq20kAKFKvXNwLPLBsMIuQJ+1C3tkvQ6PugY/zzg0
6UGcgehlhf20lTtzqclYipophRCTl26nu7y2PkanPxRzfO62p7ygfcM38ZgqkrfK
b+GFXTB951k4aVsfNFmqbZrdpaY2E7Ybhx208cU6SfMhYvZYE6SpRc3f8zuj/w3P
ub3NFepdwg+Q2bVZuSwxX0OuWmoq06cAaAbODKzwNgjFaLxq3jXOVnZZnm7G8TVn
W85BC8RTlIStcd09Jp+tassKU+cMNA==
=r7tD
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2025-01-07' of https://gitlab.freedesktop.org/drm/i915/kernel into drm-next
Driver Changes:
- Some DG2 refactor to fix DG2 bugs when operating with certain CPUs (Raag)
- Use hw support for min/interim ddb allocation for async flip (Vinod)
- More general code refactor to allow full display separation (Jani)
- Expose dsc sink max slice count via debugfs (Swati)
- Fix C10 pll programming sequence (Suraj)
- Fix DG1 power gate sequence (Rodrigo)
- Use preemption timeout on selftest cleanup (Janusz)
- DP DSC related fixes (Ankit)
- Fix HDCP compliance test (Suraj)
- Clean and Optimise mtl_ddi_prepare_link_retrain (Suraj)
- Adjust Added Wake Time with PKG_C_LATENCY (Animesh)
- Enabling uncompressed 128b/132b UHBR SST (Jani)
- Handle hdmi connector init failures, and no HDMI/DP cases (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Z31_WPbBoHkwgEA9@intel.com
The struct drm_dp_mst_topology_mgr *mgr parameter is only used for debug
logging in case the passed in link rate or lane count are zero. There's
no further error checking as such, and the function returns 0.
There should be no case where the parameters are zero. The returned
value is generally used as a divisor, and if we were hitting this, we'd
be seeing division by zero.
Just remove the debug logging altogether, along with the mgr parameter,
so that the function can be used in non-MST contexts without the
topology manager.
v2: Also remove drm_dp_mst_helper_tests_init as unnecessary (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/72d77e7a7fe69c784e9df048b7e6f250fd7599e4.1735912293.git.jani.nikula@intel.com
The mode_valid() callbacks of drm_encoder, drm_crtc and drm_bridge
take a const struct drm_display_mode argument. Change the mode_valid
callback of drm_connector to also take a const argument.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241214-drm-connector-mode-valid-const-v2-5-4f9498a4c822@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Extend drm_bridge_connector code to read the EDID and use it to update
connector status if the bridge chain implements HDMI bridge. Performing
it from the generic location minimizes individual bridge's code and
enforces standard behaviour from all corresponding drivers.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-drm-bridge-hdmi-connector-v10-7-dc89577cd438@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The HDMI Connectors need to perform a variety of tasks when the HDMI
connector state changes. Such tasks include setting or invalidating CEC
address, notifying HDMI codec driver, updating scrambler data, etc.
Implementing such tasks in a driver-specific callbacks is error prone.
Start implementing the generic helper function (currently handling only
the HDMI Codec framework) to be used by drivers utilizing HDMI Connector
framework.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-drm-bridge-hdmi-connector-v10-6-dc89577cd438@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add necessary glue code to be able to use new HDMI codec framework from
the DRM bridge drivers. The drm_bridge implements a limited set of the
hdmi_codec_ops interface, with the functions accepting both
drm_connector and drm_bridge instead of just a generic void pointer.
This framework is integrated with the DRM HDMI Connector framework, but
can also be used for DisplayPort connectors.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-drm-bridge-hdmi-connector-v10-4-dc89577cd438@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Several DRM drivers implement HDMI codec support (despite its name it
applies to both HDMI and DisplayPort drivers). Implement generic
framework to be used by these drivers. This removes a requirement to
implement get_eld() callback and provides default implementation for
codec's plug handling.
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-drm-bridge-hdmi-connector-v10-3-dc89577cd438@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The bridges using HDMI connector framework have a call to
drm_atomic_helper_connector_hdmi_check() in their atomic_check()
callback. In order to reduce boilerplate and make simplify bridge's
code, use drm_atomic_helper_connector_hdmi_check() to implement
drm_connector.atomic_check() for HDMI bridges.
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241210-bridge_hdmi_check-v1-1-a8fdd8c5afa5@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Our infoframe setting code currently lacks the ability to clear
infoframes. For some of the infoframes, we only need to replace them,
so if an error occurred when generating a new infoframe we would leave
a stale frame instead of clearing the frame.
However, the Dynamic Range and Mastering (DRM) infoframe should only
be present when displaying HDR content (ie: the HDR_OUTPUT_METADATA blob
is set). If we can't clear infoframes, the stale DRM infoframe will
remain and we can never set the display back to SDR mode.
With this change, we clear infoframes when they can not, or should not,
be generated. This fixes switching to an SDR mode from an HDR one.
Fixes: f378b77227 ("drm/connector: hdmi: Add Infoframes generation")
Signed-off-by: Derek Foreman <derek.foreman@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241202181939.724011-1-derek.foreman@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
MST connectors should be initialized/registered by calling
drm_connector_dynamic_init()/drm_connector_dynamic_register(). The
commit adding these functions explains the issue with the current
drm_connector_init*()/drm_connector_register() interface for MST
connectors.
Based on the above adjust here the registration part and change the
initialization part in follow-up commits for each driver.
For now, drivers are allowed to keep using the drm_connector_init*()
functions, by drm_connector_dynamic_register() checking for this (see
drm_connector_add()). A commit later will change this to WARN in such
cases.
v2: Replaces references to a "patch" with "commit" in the commit log.
(Jani)
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Wayne Lin <wayne.lin@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Danilo Krummrich <dakr@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241211230328.4012496-5-imre.deak@intel.com
Instead of returning a generic NULL on error from
drm_dp_tunnel_mgr_create(), use error pointers with informative codes
to align the function with stub that is executed when
CONFIG_DRM_DISPLAY_DP_TUNNEL is unset. This will also trigger IS_ERR()
in current caller (intel_dp_tunnerl_mgr_init()) instead of bypassing it
via NULL pointer.
v2: use error codes inside drm_dp_tunnel_mgr_create() instead of handling
on caller's side (Michal, Imre)
v3: fixup commit message and add "CC"/"Fixes" lines (Andi),
mention aligning function code with stub
Fixes: 91888b5b1a ("drm/i915/dp: Add support for DP tunnel BW allocation")
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v6.9+
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7q4fpnmmztmchczjewgm6igy55qt6jsm7tfd4fl4ucfq6yg2oy@q4lxtsu6445c
The v6.13-rc2 release included a bunch of breaking changes,
specifically the MODULE_IMPORT_NS commit.
Backmerge in order to fix them before the next pull-request.
Include the fix from Stephen Roswell.
Caused by commit
25c3fd1183 ("drm/virtio: Add a helper to map and note the dma addrs and lengths")
Interacting with commit
cdd30ebb1b ("module: Convert symbol namespace to string literal")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20241209121717.2abe8026@canb.auug.org.au
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
After an out-of-memory error the reception state should be reset, so
that the next attempt receiving a message doesn't fail (due to getting a
start-of-message packet, while the reception state has already the
start-of-message flag set).
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203160223.2926014-7-imre.deak@intel.com
While receiving an MST up request message from one thread in
drm_dp_mst_handle_up_req(), the MST topology could be removed from
another thread via drm_dp_mst_topology_mgr_set_mst(false), freeing
mst_primary and setting drm_dp_mst_topology_mgr::mst_primary to NULL.
This could lead to a NULL deref/use-after-free of mst_primary in
drm_dp_mst_handle_up_req().
Avoid the above by holding a reference for mst_primary in
drm_dp_mst_handle_up_req() while it's used.
v2: Fix kfreeing the request if getting an mst_primary reference fails.
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204132007.3132494-1-imre.deak@intel.com
If receiving a reply for an MST down request message times out, the
thread receiving the reply in drm_dp_mst_handle_down_rep() could try to
dereference the drm_dp_sideband_msg_tx txmsg request message after the
thread waiting for the reply - calling drm_dp_mst_wait_tx_reply() - has
timed out and freed txmsg, hence leading to a use-after-free in
drm_dp_mst_handle_down_rep().
Prevent the above by holding the drm_dp_mst_topology_mgr::qlock in
drm_dp_mst_handle_down_rep() for the whole duration txmsg is looked up
from the request list and dereferenced.
v2: Fix unlocking mgr->qlock after verify_rx_request_type() fails.
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203174632.2941402-1-imre.deak@intel.com
Simplify the error return path in drm_dp_mst_handle_down_rep(),
preparing for the next patch.
While at it use reset_msg_rx_state() instead of open-coding it.
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203160223.2926014-4-imre.deak@intel.com
After receiving the response for an MST down request message, the
response should be accepted/parsed only if the response type matches
that of the request. Ensure this by checking if the request type code
stored both in the request and the reply match, dropping the reply in
case of a mismatch.
This fixes the topology detection for an MST hub, as described in the
Closes link below, where the hub sends an incorrect reply message after
a CLEAR_PAYLOAD_TABLE -> LINK_ADDRESS down request message sequence.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/12804
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203160223.2926014-3-imre.deak@intel.com
If the MST topology is removed during the reception of an MST down reply
or MST up request sideband message, the
drm_dp_mst_topology_mgr::up_req_recv/down_rep_recv states could be reset
from one thread via drm_dp_mst_topology_mgr_set_mst(false), racing with
the reading/parsing of the message from another thread via
drm_dp_mst_handle_down_rep() or drm_dp_mst_handle_up_req(). The race is
possible since the reader/parser doesn't hold any lock while accessing
the reception state. This in turn can lead to a memory corruption in the
reader/parser as described by commit bd2fccac61 ("drm/dp_mst: Fix MST
sideband message body length check").
Fix the above by resetting the message reception state if needed before
reading/parsing a message. Another solution would be to hold the
drm_dp_mst_topology_mgr::lock for the whole duration of the message
reception/parsing in drm_dp_mst_handle_down_rep() and
drm_dp_mst_handle_up_req(), however this would require a bigger change.
Since the fix is also needed for stable, opting for the simpler solution
in this patch.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 1d082618bb ("drm/display/dp_mst: Fix down/up message handling after sink disconnect")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/13056
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203160223.2926014-2-imre.deak@intel.com
Use new drm_bridge_connector_mode_valid() helper if there is a HDMI
bridge in the bridge chain. This removes the need to perform TMDS char
rate check manually in the bridge driver.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241130-hdmi-mode-valid-v5-7-742644ec3b1f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SST with 128b/132b channel coding needs this too. Extract to a separate
helper, independent of MST.
Pass timeout in as a parameter, anticipating that we can reduce the
timeout for SST.
v2: Clean up kernel-doc a bit
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/459fd3e96a55a8ea8ada8d27d93eaa24c235f9c1.1733238941.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the 2 simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups that
can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog
As mentioned above, there is 2 merge conflicts with your tree, one is
where the file is removed (easy enough to resolve), the second is a
build time error, that has been found in linux-next and the fix can be
seen here:
https://lore.kernel.org/r/20241107212645.41252436@canb.auug.org.au
Other than that, the changes here have been in linux-next with no other
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lEog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym+0ACgw6wN+LkLVIHWhxTq5DYHQ0QCxY8AoJrRIcKe
78h0+OU3OXhOy8JGz62W
=oI5S
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
Fix the MST sideband message body length check, which must be at least 1
byte accounting for the message body CRC (aka message data CRC) at the
end of the message.
This fixes a case where an MST branch device returns a header with a
correct header CRC (indicating a correctly received body length), with
the body length being incorrectly set to 0. This will later lead to a
memory corruption in drm_dp_sideband_append_payload() and the following
errors in dmesg:
UBSAN: array-index-out-of-bounds in drivers/gpu/drm/display/drm_dp_mst_topology.c:786:25
index -1 is out of range for type 'u8 [48]'
Call Trace:
drm_dp_sideband_append_payload+0x33d/0x350 [drm_display_helper]
drm_dp_get_one_sb_msg+0x3ce/0x5f0 [drm_display_helper]
drm_dp_mst_hpd_irq_handle_event+0xc8/0x1580 [drm_display_helper]
memcpy: detected field-spanning write (size 18446744073709551615) of single field "&msg->msg[msg->curlen]" at drivers/gpu/drm/display/drm_dp_mst_topology.c:791 (size 256)
Call Trace:
drm_dp_sideband_append_payload+0x324/0x350 [drm_display_helper]
drm_dp_get_one_sb_msg+0x3ce/0x5f0 [drm_display_helper]
drm_dp_mst_hpd_irq_handle_event+0xc8/0x1580 [drm_display_helper]
Cc: <stable@vger.kernel.org>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241125205314.1725887-1-imre.deak@intel.com
fwnode needs to be set for a device for fw_devlink to be able to
track/enforce its dependencies correctly. Without this, you'll see error
messages like this when the supplier has probed and tries to make sure
all its fwnode consumers are linked to it using device links:
mediatek-drm-dp 1c500000.edp-tx: Failed to create device link (0x180) with backlight-lcd0
Reported-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Closes: https://lore.kernel.org/all/7b995947-4540-4b17-872e-e107adca4598@notapiano/
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241024061347.1771063-2-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow the interlace_allowed example and calculate drm_connector's
ycbcr_420_allowed flag as AND of all drm_bridge's ycbcr_420_allowed
flags in a chain. This is one of the gaps between several
bridge-specific connector implementations and drm_bridge_connector.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241019-bridge-yuv420-v1-1-d74efac9e4e6@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
To avoid reintroducing the randconfig bug originally fixed by commit
876271118a ("drm/display: Fix build error without CONFIG_OF"),
DRM_MSM which selects DRM_DISPLAY_DP_HELPER must explicitly depend
on OF. This is consistent with what all other DRM drivers are doing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241015134606.5b87093e@endymion.delvare
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
GCC 15 enables -Werror=unterminated-string-initialization by default.
This results in the following build error
drivers/gpu/drm/display/drm_dp_dual_mode_helper.c: In function ‘is_hdmi_adaptor’:
drivers/gpu/drm/display/drm_dp_dual_mode_helper.c:164:17: error: initializer-string for array of
‘char’ is too long [-Werror=unterminated-string-initialization]
164 | "DP-HDMI ADAPTOR\x04";
| ^~~~~~~~~~~~~~~~~~~~~
After discussion with Ville, the fix was to increase the size of
dp_dual_mode_hdmi_id array by one, so that it can accommodate the NULL
line character. This should let us build the kernel with GCC 15.
Signed-off-by: Brahmajit Das <brahmajit.xyz@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241002092311.942822-1-brahmajit.xyz@gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm-misc-next for v6.12:
UAPI Changes:
- Add panthor/DEV_QUERY_TIMESTAMP_INFO query.
Cross-subsystem Changes:
- Updated dt bindings.
- Add documentation explaining default errnos for fences.
- Mark dma-buf heaps creation functions as __init.
Core Changes:
- Split DSC helpers from DP helpers.
- Clang build fixes for drm/mm test.
- Remove simple pipeline support for gem-vram,
no longer any users left after converting bochs.
- Add erno to drm_sched_start to distinguish between GPU and queue
reset.
- Add drm_framebuffer testcases.
- Fix uninitialized spinlock acquisition with CONFIG_DRM_PANIC=n.
- Use read_trylock instead of read_lock in dma_fence_begin_signalling to
quiesce lockdep.
Driver Changes:
- Assorted small fixes and updates for tegra, host1x, imagination,
nouveau, panfrost, panthor, panel/ili9341, mali, exynos,
panel/samsung-s6e3fa7, ast, bridge/ti-sn65dsi86, panel/himax-hx83112a,
bridge/tc358767, bridge/imx8mp-hdmi-tx, panel/khadas-ts050,
panel/nt36523, panel/sony-acx565akm, kmb, accel/qaic, omap, v3d.
- Add bridge/TI TDP158.
- Assorted documentation updates.
- Convert bochs from simple drm to gem shmem, and check modes
against available memory.
- Many VC4 fixes, most related to scaling and YUV support.
- Convert some drivers to use SYSTEM_SLEEP_PM_OPS and RUNTIME_PM_OPS.
- Rockchip 4k@60 support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/445713a6-2427-4c53-8ec2-3a894ec62405@linux.intel.com
The largest infoframe we create is the DRM (Dynamic Range Mastering)
infoframe which is 26 bytes + a 4 byte header, for a total of 30
bytes.
With HDMI_MAX_INFOFRAME_SIZE set to 29 bytes, as it is now, we
allocate too little space to pack a DRM infoframe in
write_device_infoframe(), leading to an ENOSPC return from
hdmi_infoframe_pack(), and never calling the connector's
write_infoframe() vfunc.
Instead of having HDMI_MAX_INFOFRAME_SIZE defined in two places,
replace HDMI_MAX_INFOFRAME_SIZE with HDMI_INFOFRAME_SIZE(MAX) and make
MAX 27 bytes - which is defined by the HDMI specification to be the
largest infoframe payload.
Fixes: f378b77227 ("drm/connector: hdmi: Add Infoframes generation")
Fixes: c602e4959a ("drm/connector: hdmi: Create Infoframe DebugFS entries")
Signed-off-by: Derek Foreman <derek.foreman@collabora.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240827163918.48160-1-derek.foreman@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Atm it's assumed that all Synaptics MST branch devices support DSC,
which is not exposed via a DP-to-DP peer device, rather a control flag
in the branch device's UFP DPCD applying to all the streams going
through it. This isn't true for all adapters with this branch device
though (for instance the Cakitte USBC->2xHDMI adapter reported in the
Closes link below doesn't support DSC).
Fix the above by advertising the DSC decompression support only if the
capability flag for this in the UFP DPCD is actually set.
Cc: Lyude Paul <lyude@redhat.com>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/12047
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240909144650.2931258-1-imre.deak@intel.com
On HDMI connectors which use drm_bridge_connector and DRM_BRIDGE_OP_HDMI
IGT chokes on the max_bpc property in several kms_properties tests due
to the drm_bridge_connector failing to reset HDMI-related
properties.
Call __drm_atomic_helper_connector_hdmi_reset() if the
drm_bridge_connector has bridge_hdmi.
It is impossible to call this function from HDMI bridges, none of the
bridge callbacks correspond to the drm_connector_funcs::reset().
Fixes: 6b4468b0c6 ("drm/bridge-connector: implement glue code for HDMI connector")
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240903-drm-bridge-connector-fix-hdmi-reset-v5-3-daebde6d9857@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_bridge_connector is a "leaf" driver, belonging to the display
helper, rather than the "CRTC" drm_kms_helper module. Move the driver
to the drm/display and add necessary Kconfig selection clauses.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240903-drm-bridge-connector-fix-hdmi-reset-v5-2-daebde6d9857@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Kconfig symbols should not declare dependency on DRM_DISPLAY_HELPER.
Move all parts of DRM_DISPLAY_HELPER to an if DRM_DISPLAY_HELPER block.
It is not possible to make those symbols select DRM_DISPLAY_HELPER
because of the link issues when a part of the helper is selected to be
built-in, while other part is selected to be as module. In such a case
the modular part doesn't get built at all, leading to undefined symbols.
The only viable alternative is to split drm_display_helper.ko into
several small modules, each of them having their own dependencies.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240903-drm-bridge-connector-fix-hdmi-reset-v5-1-daebde6d9857@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Currently the DRM DSC functions are selected by the
DRM_DISPLAY_DP_HELPER Kconfig symbol. This is not optimal, since the DSI
code (both panel and host drivers) end up selecting the seemingly
irrelevant DP helpers. Split the DSC code to be guarded by the separate
DRM_DISPLAY_DSC_HELPER Kconfig symbol.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #i915
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240704-panel-sw43408-fix-v6-1-3ea1c94bbb9b@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Instead of just smashing jiffies into a GUID, use guid_gen() to generate
RFC 4122 compliant GUIDs.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240812122312.1567046-2-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The kernel has a guid_t type for GUIDs. Switch to using it, but avoid
any functional changes here.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240812122312.1567046-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Sync with v6.11-rc1 in general, and specifically get the new
BACKLIGHT_POWER_ constants for power states.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In the
if (old_ddps != port->ddps || !created)
if (port->ddps && !port->input)
ret = drm_dp_send_enum_path_resources();
sequence the first if's condition is true if the port exists already
(!created) or the port was created anew (hence old_ddps==0) and it was
in the plugged state (port->ddps==1). The second if's condition is true
for output ports in the plugged state. So the function is called for an
output port in the plugged state, regardless if it already existed or
not and regardless of the old plugged state. In all other cases
port->full_pbn can be zeroed as the port is either an input for which
full_pbn is never set, or an output in the unplugged state for which
full_pbn was already zeroed previously or the port was just created
(with port->full_pbn==0).
Simplify the condition, making it clear that the path resources are
always enumerated for an output port in the plugged state.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-4-imre.deak@intel.com
Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases to
get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions. It's not all that useful for a "write a whole driver
in rust" type of thing, but the firmware bindings do help out the
phy rust drivers, and the driver core bindings give a solid base on
which others can start their work. There is still a long way to go
here before we have a multitude of rust drivers being added, but
it's a great first step.
- driver core const api changes. This reached across all bus types,
and there are some fix-ups for some not-common bus types that
linux-next and 0-day testing shook out. This work is being done to
help make the rust bindings more safe, as well as the C code, moving
toward the end-goal of allowing us to put driver structures into
read-only memory. We aren't there yet, but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZqH+aQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoOQCfVBdLcBjEDAGh3L8qHRGMPy4rV2EAoL/r+zKm
cJEYtJpGtWX6aAtugm9E
=ZyJV
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
Single characters should be put into a sequence.
Thus use the corresponding function “seq_putc” for one selected call.
This issue was transformed by using the Coccinelle software.
Suggested-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/af602b2e-4d92-4c54-9884-7db84700aa93@web.de
Add a helper to dump the Display Stream Compression configuration, taken
into use in the i915 driver by a later patch.
v2:
- Rebase on the s/DRM_X16/FXP_Q4 change.
- s/DSC configration/DSC configuration in the function documentation.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240628164451.1177612-3-imre.deak@intel.com
Add helpers to convert between q4 fixed point and integer/fraction
values. Also add the format/argument macros required to printk q4 fixed
point variables. The q4 notation is based on the short variant described
by
https://en.wikipedia.org/wiki/Q_(number_format)
where only the number of fraction bits in the fixed point value are
defined, while the full size is deducted from the container type, that
is the size of int for these helpers. Using the fxp_ prefix, which makes
moving these helpers outside of drm to a more generic place easier, if
they prove to be useful.
These are needed by later patches dumping the Display Stream Compression
configuration in DRM core and in the i915 driver to replace the
corresponding bpp_x16 helpers defined locally in the driver.
v2: Use the more generic/descriptive fxp_q4 prefix instead of drm_x16.
(Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240628164451.1177612-2-imre.deak@intel.com
[Why]
During resume, observe that we receive CSN event before we start topology
probing. Handling CSN at this moment based on uncertain topology is
unnecessary.
[How]
Add checking condition in drm_dp_mst_handle_up_req() to skip handling CSN
if the topology is yet to be probed.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626084825.878565-3-Wayne.Lin@amd.com
[Why]
After supend/resume, with topology unchanged, observe that
link_address_sent of all mstb are marked as false even the topology probing
is done without any error.
It is caused by wrongly also include "ret == 0" case as a probing failure
case.
[How]
Remove inappropriate checking conditions.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Fixes: 37dfdc55ff ("drm/dp_mst: Cleanup drm_dp_send_link_address() a bit")
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626084825.878565-2-Wayne.Lin@amd.com
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_MODVERSIONS is enabled, then using the HDMI Connector
framework can result in build failures. Rename the function to make it
fit into the name requirements.
ERROR: modpost: too long symbol "drm_atomic_helper_connector_hdmi_disable_audio_infoframe" [drivers/gpu/drm/msm/msm.ko]
Reported-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240624-hdmi-connector-shorten-name-v1-1-5bd3410138db@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add drm_atomic_helper_connector_hdmi_disable_audio_infoframe(), an API
to allow the driver disable sending the Audio Infoframe. This is to be
used by the drivers if setup of the infoframes is not tightly coupled
with the audio functionality and just disabling the audio playback
doesn't stop the HDMI hardware from sending the Infoframe.
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607-bridge-hdmi-connector-v5-1-ab384e6021af@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Infoframes in KMS is usually handled by a bunch of low-level helpers
that require quite some boilerplate for drivers. This leads to
discrepancies with how drivers generate them, and which are actually
sent.
Now that we have everything needed to generate them in the HDMI
connector state, we can generate them in our common logic so that
drivers can simply reuse what we precomputed.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-22-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
HDMI controller drivers will need to figure out the RGB range they need
to configure based on a mode and property values. Let's expose that in
the HDMI connector state so drivers can just use that value.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-20-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The i915 driver has a property to force the RGB range of an HDMI output.
The vc4 driver then implemented the same property with the same
semantics. KWin has support for it, and a PR for mutter is also there to
support it.
Both drivers implementing the same property with the same semantics,
plus the userspace having support for it, is proof enough that it's
pretty much a de-facto standard now and we can provide helpers for it.
Let's plumb it into the newly created HDMI connector.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Sebastian Wick <sebastian.wick@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-18-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Now that we have all the infrastructure needed, we can add some code
that will, for a given connector state and mode, compute the best output
format and bpc.
The algorithm is equivalent to the one already found in i915 and vc4.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-15-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of the HDMI controllers have an upper TMDS character rate limit
they can't exceed. On "embedded"-grade display controllers, it will
typically be lower than what high-grade monitors can provide these days,
so drivers will filter the TMDS character rate based on the controller
capabilities.
To make that easier to handle for drivers, let's provide an optional
hook to be implemented by drivers so they can tell the HDMI controller
helpers if a given TMDS character rate is reachable for them or not.
This will then be useful to figure out the best format and bpc count for
a given mode.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-13-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most HDMI drivers have some code to calculate the TMDS character rate,
usually to adjust an internal clock to match what the mode requires.
Since the TMDS character rates mostly depends on the resolution, whether
we need to repeat pixels or not, the bpc count and the format, we can
now derive it from the HDMI connector state that stores all those infos
and remove the duplication from drivers.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-11-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
A lot of HDMI drivers have some variation of the formula to calculate
the TMDS character rate from a mode, but few of them actually take all
parameters into account.
Let's create a helper to provide that rate taking all parameters into
account.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-9-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The next features we will need to share across drivers will need to
store some parameters for drivers to use, such as the selected output
format.
Let's create a new connector sub-state dedicated to HDMI controllers,
that will eventually store everything we need.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-3-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit d674858ff9, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/3db958e3f4002e26cd963596d810c37feb315fb3.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit e075e496f5, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1ba76cc4d96a8afefff5d1bc42fb1e1329c5da68.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit 4d15125d7f, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/79824fec01eb9ab0673b9409f9b39cc8b5cc338d.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit 0323287de8, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/89ac456805746b6d0c888f10c5120b11aacd3319.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit 3166e7e6d9, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/a40e70a0abd3d841c23c107d452a43fdd70ef37a.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commit f6d2dc03fa, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/bd288a5943dab8609f2d1f2bf413595a61df727a.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmYlapoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGJLgH/RFrsXefpxAWACJv
wRmIx/YFjI3Z4nypBZPXysX/JOuf/cf4bR22jMHC1vhQDtxVgB7eUpEYx0C0Y5RD
ll7cunAZCpP+PB725/bOWbaF94eigl8xC4RrKPon4tG1CS9NAvCJFDyNgWpqh48s
sSKKae68a16zMtIX5Za8nvmsBQOeD67ZFBgI4m7wIDDhTXY3XlG84r8Rz/ZwcdE/
rExFkDMUqjpoJVAMBtETQNk4pvKZVMrW2B0f/xZSR+IKXw5l2FO0raXkIG/6TERs
CxJvCuUjKIosqFLIK2O/cU9G+5V2axZ/WD8YRwDr2vlnnOPht+dFQzyPcuSqezbG
ShIhQo8=
=GI5F
-----END PGP SIGNATURE-----
Backmerge tag 'v6.9-rc5' into drm-next
Linux 6.9-rc5
I've had a persistent msm failure on clang, and the fix is in fixes
so just pull it back to fix that.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Enabling the 5k@60Hz uncompressed mode on the MediaTek/Dell U3224KBA
monitor results in a blank screen, at least on MTL platforms on UHBR
link rates with some (<30) uncompressed bpp values. Enabling compression
fixes the problem, so do that for now. Windows enables DSC always if the
sink supports it and forcing it to enable the mode without compression
leads to the same problem above (which suggests a panel issue with
uncompressed mode).
The same 5k mode on non-UHBR link rates is not affected and lower
resolution modes are not affected either. The problem is similar to the
one fixed by the HBLANK expansion quirk on Synaptics hubs, with the
difference that the problematic mode has a longer HBLANK duration. Also
the monitor doesn't report supporting HBLANK expansion; either its
internal MST hub does the expansion internally - similarly to the
Synaptics hub - or the issue has another root cause, but still related
to the mode's short HBLANK duration. Enable the quirk for the monitor
adjusting the detection for the above differences.
v2: Rebase on drm_dp_128132b_supported() change.
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240417142217.457902-1-imre.deak@intel.com
Add a function to get the AUX device of the parent of an MST port, used
by a follow-up i915 patch in the patchset.
v2: Move drm_dp_mst_aux_for_parent() forward declaration to this patch
(Ankit)
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416221010.376865-10-imre.deak@intel.com
Factor out a function to check if an MST port is logical, used by a
follow-up i915 patch in the patchset.
v2: Move drm_dp_mst_aux_for_parent() forward declaration to the next
patch. (Ankit)
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416221010.376865-9-imre.deak@intel.com
- Fix documentation of DP tunnel functions (Imre)
- DP MST read sideband messaging cap (Jani)
- Preparation patches for Adaptive Sync SDP Support for DP (Mitul)
Driver Changes:
i915 core (non-display):
- Documentation improvements (Nirmoy)
- Add includes for BUG_ON/BUILD_BUG_ON in i915_memcpy.c (Joonas)
- Do not print 'pxp init failed with 0' when it succeed (Jose)
- Clean-up, including removal of dead code for unsupported platforms (Lucas)
- Adding new DG2 PCI ID (Ravi)
{i915,xe} display:
- Spelling fix (Colin Ian)
- Document CDCLK components (Gustavo)
- Lunar Lake display enabling, including cdclk and other refactors (Gustavo, Bala)
- BIOS/VBT/opregion related refactor (Jani, Ville, RK)
- Save a few bytes of memory using {kstrdup,kfree}_const variant (Christophe)
- Digital port related refactor/clean-up (Ville)
- Fix 2s boot time regression on DP panel replay init (Animesh)
- Remove redundant drm_rect_visible() overlay use (Arthur)
- DSC HW state readout fixes (Imre)
- Remove duplication on audio enable/disable on SDVO and g4x+ DP (Ville)
- Disable AuxCCS framebuffers if built for Xe (Juha-Pekka)
- Fix DSI init order (Ville)
- DRRS related refactor and fixes (Bhanuprakash)
- Fix DSB vblank waits with VRR (Ville)
- General improvements on register name and use of REG_BIT (Ville)
- Some display power well related improvements (Ville)
- FBC changes for better w/a handling (Ville)
- Make crtc disable more atomic (Ville)
- Fix hwmon locking inversion in sysfs getter (Janusz)
- Increase DP idle pattern wait timeout to 2ms (Shekhar)
- PSR related fixes and improvents (Jouni)
- Start using container_of_const() for some extra const safety (Ville)
- Use drm_printer more on display code (Ville)
- Fix Jasper Lake boot freeze (Jonathon)
- Update Pipe src size check in skl_update_scaler (Ankit)
- Enable MST mode for 128b/132b single-stream sideband (Jani)
- Pass encoder around more for port/phy checks (Jani)
- Some initial work to make display code more independent from i915 (Jani)
- Pre-populate the cursor physical dma address (Ville)
- Do not bump min backlight brightness to max on enable (Gareth)
- Fix MTL supported DP rates - removal of UHBR13.5 (Arun)
- Fix the computation for compressed_bpp for DISPLAY < 1 (Ankit)
- Bigjoiner modeset sequence redesign and MST support (Ville)
- Enable Adaptive Sync SDP Support for DP (Mitul)
- Implemnt vblank sycnhronized mbus joining changes (Ville, Stanislav)
- HDCP related fixes (Suraj)
- Fix i915_display_info debugfs when connectors are not active (Ville)
- Clean up on Xe compat layer (Jani)
- Add jitter WAs for MST/FEC/DSC links (Imre)
- DMC wakelock implementation (Luca)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmYfzQEACgkQ+mJfZA7r
E8qYvAf/T8KrEewHOWz7NOaKcFRCNYaF4QTdVOfgHUYBX5NPDF/xzwFdHCL8QWQu
bwKwE2b94VEyruG3DYwTMd8GNcDxrsOrmU0IZe3PVkm+BvHLTmrOqL6BlCd85zXF
02IuE+LCaWREmmpLMcsDMxsaaq8yp+cw9/F0jJDrH6LiyfxFriefxyZYpGYjRCuv
8GP1fHXLFV2yys4rveR/+y9xIhgy82mVcg3/Kfk0+er7gALkY6Vc0N38wedET9MZ
ZPfVidBeaTkIKcCDFKnFzGjG+9rNQ7NFrXyS7Hl97VolGt2l03qGGPNW1PouDiUx
7Y8CJOc+1k9wyBMKl0a/NQBRAqSZBQ==
=JvZN
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2024-04-17-1' of https://anongit.freedesktop.org/git/drm/drm-intel into drm-next
Core Changes (DRM):
- Fix documentation of DP tunnel functions (Imre)
- DP MST read sideband messaging cap (Jani)
- Preparation patches for Adaptive Sync SDP Support for DP (Mitul)
Driver Changes:
i915 core (non-display):
- Documentation improvements (Nirmoy)
- Add includes for BUG_ON/BUILD_BUG_ON in i915_memcpy.c (Joonas)
- Do not print 'pxp init failed with 0' when it succeed (Jose)
- Clean-up, including removal of dead code for unsupported platforms (Lucas)
- Adding new DG2 PCI ID (Ravi)
{i915,xe} display:
- Spelling fix (Colin Ian)
- Document CDCLK components (Gustavo)
- Lunar Lake display enabling, including cdclk and other refactors (Gustavo, Bala)
- BIOS/VBT/opregion related refactor (Jani, Ville, RK)
- Save a few bytes of memory using {kstrdup,kfree}_const variant (Christophe)
- Digital port related refactor/clean-up (Ville)
- Fix 2s boot time regression on DP panel replay init (Animesh)
- Remove redundant drm_rect_visible() overlay use (Arthur)
- DSC HW state readout fixes (Imre)
- Remove duplication on audio enable/disable on SDVO and g4x+ DP (Ville)
- Disable AuxCCS framebuffers if built for Xe (Juha-Pekka)
- Fix DSI init order (Ville)
- DRRS related refactor and fixes (Bhanuprakash)
- Fix DSB vblank waits with VRR (Ville)
- General improvements on register name and use of REG_BIT (Ville)
- Some display power well related improvements (Ville)
- FBC changes for better w/a handling (Ville)
- Make crtc disable more atomic (Ville)
- Fix hwmon locking inversion in sysfs getter (Janusz)
- Increase DP idle pattern wait timeout to 2ms (Shekhar)
- PSR related fixes and improvents (Jouni)
- Start using container_of_const() for some extra const safety (Ville)
- Use drm_printer more on display code (Ville)
- Fix Jasper Lake boot freeze (Jonathon)
- Update Pipe src size check in skl_update_scaler (Ankit)
- Enable MST mode for 128b/132b single-stream sideband (Jani)
- Pass encoder around more for port/phy checks (Jani)
- Some initial work to make display code more independent from i915 (Jani)
- Pre-populate the cursor physical dma address (Ville)
- Do not bump min backlight brightness to max on enable (Gareth)
- Fix MTL supported DP rates - removal of UHBR13.5 (Arun)
- Fix the computation for compressed_bpp for DISPLAY < 1 (Ankit)
- Bigjoiner modeset sequence redesign and MST support (Ville)
- Enable Adaptive Sync SDP Support for DP (Mitul)
- Implemnt vblank sycnhronized mbus joining changes (Ville, Stanislav)
- HDCP related fixes (Suraj)
- Fix i915_display_info debugfs when connectors are not active (Ville)
- Clean up on Xe compat layer (Jani)
- Add jitter WAs for MST/FEC/DSC links (Imre)
- DMC wakelock implementation (Luca)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmYfzQEACgkQ+mJfZA7r
# E8qYvAf/T8KrEewHOWz7NOaKcFRCNYaF4QTdVOfgHUYBX5NPDF/xzwFdHCL8QWQu
# bwKwE2b94VEyruG3DYwTMd8GNcDxrsOrmU0IZe3PVkm+BvHLTmrOqL6BlCd85zXF
# 02IuE+LCaWREmmpLMcsDMxsaaq8yp+cw9/F0jJDrH6LiyfxFriefxyZYpGYjRCuv
# 8GP1fHXLFV2yys4rveR/+y9xIhgy82mVcg3/Kfk0+er7gALkY6Vc0N38wedET9MZ
# ZPfVidBeaTkIKcCDFKnFzGjG+9rNQ7NFrXyS7Hl97VolGt2l03qGGPNW1PouDiUx
# 7Y8CJOc+1k9wyBMKl0a/NQBRAqSZBQ==
# =JvZN
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 17 Apr 2024 23:22:09 AEST
# gpg: using RSA key 6D207068EEDD65091C2CE2A3FA625F640EEB13CA
# gpg: Good signature from "Rodrigo Vivi <rodrigo.vivi@intel.com>" [unknown]
# gpg: aka "Rodrigo Vivi <rodrigo.vivi@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6D20 7068 EEDD 6509 1C2C E2A3 FA62 5F64 0EEB 13CA
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Zh_Q72gYKMMbge9A@intel.com
The DisplayPort helpers rely on some
(__drm_atomic_helper_private_obj_duplicate_state,
drm_kms_helper_hotplug_event) helpers found in files compiled by
DRM_KMS_HELPER.
Prior to commit d674858ff9 ("drm/display: Make all helpers visible and
switch to depends on"), DRM_DISPLAY_DP_HELPER was only selectable so it
wasn't really a big deal. However, since that commit, it's now something
that can be enabled as is, and since there's no expressed dependency
with DRM_KMS_HELPER, it can break too.
Since DRM_KMS_HELPER is a selectable option for now, let's select it for
DRM_DISPLAY_DP_HELPER.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404021556.0JVcNC13-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202404021700.LbyYZGFd-lkp@intel.com/
Fixes: d674858ff9 ("drm/display: Make all helpers visible and switch to depends on")
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240403-fix-dw-hdmi-kconfig-v1-1-afbc4a835c38@kernel.org
Add structure representing Adaptive Sync Secondary Data Packet (AS SDP).
Also, add Adaptive Sync SDP logging in drm_dp_helper.c to facilitate
debugging.
--v2:
- Update logging. [Jani, Ankit]
- Use 'as_sdp' instead of 'async' [Ankit]
- Correct define placeholders to where they are actually used. [Jani]
- Update members in 'as_sdp' structure to make it uniform. [Jani]
--v3:
- Added changes to dri-devel mailing list. No code changes.
--v4:
- Instead of directly using operation mode, use an enum to accommodate
all operation modes (Ankit).
--v5:
Nit-pick changes to commit message.
--v6:
- Add correct place holder and name change for AS_SDP_OP_MODE.
- Separate i915 changes from drm changes.
- Remove extra lines.
--v7:
- Add drm/dp in subject line (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-3-mitulkumar.ajitkumar.golani@intel.com
Add an API that indicates support for Adaptive Sync SDP in
the sink, which can be utilized by the rest of the DP programming.
--v1:
- Format commit message properly.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-2-mitulkumar.ajitkumar.golani@intel.com
While studying the code I've bumped into a small typo within the
kernel-doc for two functions, apparently, due to copy-paste.
This commit fixes "sizo" word to be "size".
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: b3daa5ef52 ("drm: Add helper for DP++ adaptors")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240119102215.201474-1-oleksandr@natalenko.name
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_HDMI_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-12-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_HDCP_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-11-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_DP_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-10-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_DP_AUX_BUS to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-9-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-8-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
All the helpers Kconfig symbols so far have relied on drivers selecting
them, and that's what most drivers did.
However, this creates an issue nowadays when helpers depend on each
other, and select doesn't transitively select a dependency dependencies.
Depends on doesn't have that limitation though, so let's convert those
symbols to be dependable and use depends on between them too.
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-6-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The display kconfig helpers are not organized in any particular order,
so let's move them around to create an alphabetical order.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-5-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
While most display helpers Kconfig symbols have the DRM_DISPLAY prefix,
the DisplayPort CEC tunnelling implementation uses CONFIG_DRM_DISPLAY_DP_AUX_CEC.
Since the number of users is limited, we can easily rename it to make it
consistent.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-4-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
While most display helpers Kconfig symbols have the DRM_DISPLAY prefix,
the DisplayPort-AUX chardev interface uses DRM_DP_AUX_CHARDEV.
Since the number of users is limited and it's a selected symbol, we can
easily rename it to make it consistent.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-3-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
While most display helpers Kconfig symbols have the DRM_DISPLAY prefix,
the DisplayPort Tunnel debugging uses DRM_DISPLAY_DEBUG_DP_TUNNEL_STATE.
Since the number of users is limited and it's a selected symbol, we can
easily rename it to make it consistent.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-2-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
While most display helpers Kconfig symbols have the DRM_DISPLAY prefix,
the DisplayPort AUX bus implementation uses DRM_DP_AUX_BUS.
Since the number of users is limited and it's a selected symbol, we can
easily rename it to make it consistent.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-1-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Amend drm_dp_read_mst_cap() to return an enum, indicating "SST", "SST
with sideband messaging", or "MST". Modify all call sites to take the
new return value into account.
v2:
- Rename enumerators (Ville)
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b32a3704934871a67d06420b760e148b76c5ced8.1710839496.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix the documentation issues below, also reported by 'make htmldocs':
drivers/gpu/drm/display/drm_dp_tunnel.c:447: warning: Function parameter or struct member 'tunnel' not described in 'drm_dp_tunnel_put'
drivers/gpu/drm/display/drm_dp_tunnel.c:447: warning: Function parameter or struct member 'tracker' not described in 'drm_dp_tunnel_put'
drivers/gpu/drm/display/drm_dp_tunnel.c:1185: warning: expecting prototype for drm_dp_tunnel_atomic_get_allocated_bw(). Prototype was for drm_dp_tunnel_get_allocated_bw() instead
drivers/gpu/drm/display/drm_dp_tunnel.c:1903: warning: Function parameter or struct member 'max_group_count' not described in 'drm_dp_tunnel_mgr_create'
Fixes: 295654f7e5 ("drm/dp: Add support for DP tunneling")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240228164636.1540903-1-imre.deak@intel.com
If an eDP panel is not powered on then any attempts to talk to it over
the DP AUX channel will timeout. Unfortunately these attempts may be
quite slow. Userspace can initiate these attempts either via a
/dev/drm_dp_auxN device or via the created i2c device.
Making the DP AUX drivers timeout faster is a difficult proposition.
In theory we could just poll the panel's HPD line in the AUX transfer
function and immediately return an error there. However, this is
easier said than done. For one thing, there's no hard requirement to
hook the HPD line up for eDP panels and it's OK to just delay a fixed
amount. For another thing, the HPD line may not be fast to probe. On
parade-ps8640 we need to wait for the bridge chip's firmware to boot
before we can get the HPD line and this is a slow process.
The fact that the transfers are taking so long to timeout is causing
real problems. The open source fwupd daemon sometimes scans DP busses
looking for devices whose firmware need updating. If it happens to
scan while a panel is turned off this scan can take a long time. The
fwupd daemon could try to be smarter and only scan when eDP panels are
turned on, but we can also improve the behavior in the kernel.
Let's let eDP panels drivers specify that a panel is turned off and
then modify the common AUX transfer code not to attempt a transfer in
this case.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Eizan Miyamoto <eizan@chromium.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202141109.1.I24277520ac754ea538c9b14578edc94e1df11b48@changeid
Add support for Display Port tunneling. For now this includes the
support for Bandwidth Allocation Mode (BWA), leaving adding Panel Replay
support for later.
BWA allows using displays that share the same (Thunderbolt) link with
their maximum resolution. Atm, this may not be possible due to the
coarse granularity of partitioning the link BW among the displays on the
link: the BW allocation policy is in a SW/FW/HW component on the link
(on Thunderbolt it's the SW or FW Connection Manager), independent of
the driver. This policy will set the DPRX maximum rate and lane count
DPCD registers the GFX driver will see (0x00000, 0x00001, 0x02200,
0x02201) based on the available link BW.
The granularity of the current BW allocation policy is coarse, based on
the required link rate in the 1.62Gbs..8.1Gbps range and it may prevent
using higher resolutions all together: the display connected first will
get a share of the link BW which corresponds to its full DPRX capability
(regardless of the actual mode it uses). A subsequent display connected
will only get the remaining BW, which could be well below its full
capability.
BWA solves the above coarse granularity (reducing it to a 250Mbs..1Gps
range) and first-come/first-served issues by letting the driver request
the BW for each display on a link which reflects the actual modes the
displays use.
This patch adds the DRM core helper functions, while a follow-up change
in the patchset takes them into use in the i915 driver.
v2:
- Fix prepare_to_wait vs. wake-up cond check order in
allocate_tunnel_bw(). (Ville)
- Move tunnel==NULL checks from callers in drivers to here. (Ville)
- Avoid var inits in declaration blocks that can fail or have
side-effects. (Ville)
- Use u8 for driver and group IDs. (Ville)
- Simplify API removing drm_dp_tunnel_get/put_untracked(). (Ville)
- Reuse str_yes_no() instead of a local yes_no_chr(). (Ville)
- s/drm_dp_tunnel_atomic_clear_state()/free_tunnel_state() and unexport
the function. (Ville)
- s/clear_tunnel_group_state()/free_group_state() and move kfree() to
this function. (Ville)
- Add separate group_free_bw() helper and describe what the tunnel
estimated BW includes. (Ville)
- Improve help text for CONFIG_DRM_DISPLAY_DP_TUNNEL. (Ville)
- Add code comment explaining the purpose of DPCD reg read helpers.
(Ville)
- Add code comment describing the tunnel group name prefix format.
(Ville)
- Report the allocated BW as undetermined until the first allocation
request.
- Skip allocation requests matching the previous request.
- Clear any stale BW request status flags before a new request.
- Add missing error return check of drm_dp_tunnel_atomic_get_group_state()
in drm_dp_tunnel_atomic_set_stream_bw().
- Add drm_dp_tunnel_get_allocated_bw().
- s/drm_dp_tunnel_atomic_get_tunnel_bw/drm_dp_tunnel_atomic_get_required_bw
- Fix return value description in function doc of drm_dp_tunnel_detect().
- Add function documentation to all exported functions.
v3:
- Improve grouping of fields in drm_dp_tunnel_group struct. (Uma)
- Fix validating the BW granularity DPCD reg value. (Uma)
- Document return value of check_and_clear_status_change(). (Uma)
- Fix resetting drm_dp_tunnel_ref::tunnel in drm_dp_tunnel_ref_put().
(Ville)
- Allow for ALLOCATED_BW to change after a BWA enable/disable sequence.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-2-imre.deak@intel.com
Copy intel_dp_max_data_rate() to DRM core. It will be needed by a
follow-up DP tunnel patch, checking the maximum rate the DPRX (sink)
supports. Accordingly use the drm_dp_max_dprx_data_rate() name for
clarity. This patchset will also switch calling the new DRM function
in i915 instead of intel_dp_max_data_rate().
While at it simplify the function documentation/comments, removing
parts described already by drm_dp_bw_channel_coding_efficiency().
v2: (Ville)
- Remove max_link_rate_kbps.
- Simplify the function documentation.
v3:
- Rebased on latest drm-tip.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-1-imre.deak@intel.com
YUV420 format is supported only in the VSC SDP packet and not through
MSA. Hence add an API which indicates the sink support which can be used
by the rest of the DP programming.
changes in v5:
- rebased on top of drm-tip
changes in v4:
- bail out early if dpcd rev check fails
changes in v3:
- fix the commit title prefix to drm/dp
- get rid of redundant !!
- break out this change from series [1] to get acks from drm core
maintainers
Changes in v2:
- Move VSC SDP support check API from dp_panel.c to
drm_dp_helper.c
[1]: https://patchwork.freedesktop.org/series/129180/
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240215191556.3227259-1-quic_abhinavk@quicinc.com
Currently the size parameter of drm_dp_vsc_sdp_pack() is always
the size of struct dp_sdp. Hence lets drop this parameter and
use sizeof() directly.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220195348.1270854-2-quic_abhinavk@quicinc.com
intel_dp_vsc_sdp_pack() can be re-used by other DRM drivers as well.
Lets move this to drm_dp_helper to achieve this.
changes in v2:
- rebased on top of drm-tip
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220195348.1270854-1-quic_abhinavk@quicinc.com
Backmerging to update drm-misc-next to the state of v6.8-rc3. Also
fixes a build problem with xe.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Stephen Rothwell reported htmldocs warnings when merging drm-intel
tree:
Documentation/gpu/drm-kms-helpers:296: drivers/gpu/drm/display/drm_dp_mst_topology.c:5484: ERROR: Unexpected indentation.
Documentation/gpu/drm-kms-helpers:296: drivers/gpu/drm/display/drm_dp_mst_topology.c:5488: WARNING: Block quote ends without a blank line; unexpected unindent.
Separate @failing_port return value list by surrounding it with a
blank line to fix above warnings.
Fixes: 1cd0a5ea42 ("drm/dp_mst: Factor out a helper to check the atomic state of a topology manager")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/20231114141715.6f435118@canb.auug.org.au/
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114081033.27343-1-bagasdotme@gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(controllers set the flag, but there is no client to use it). Also,
CLASS_SPD support gets simplified to prepare removal in the future.
Class based instantiation is not recommended these days anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it. Then, there are also
quite some driver updates. Standing out are patches for the wmt-driver
which is refactored to support more variants. This is the rebased pull
request where a large series for the designware driver was dropped.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEEOZGx6rniZ1Gk92RdFA3kzBSgKbYFAmWph0UPHHdzYUBrZXJu
ZWwub3JnAAoJEBQN5MwUoCm2kbIQAJotSmX0mM+nNPReYCMMiloxoxUwgpiErNwY
WDrYQSezthAJ1LDsGOEeLcE4f4I+UcUHBO1BoERtOZg3cGtE0Ii5N845sp100S9O
ktyaKS5utoErymThWFFrnZX60/8yKXUMzZmNzy96560gPcxbFyyyVhKfBSPzK9T+
O8CGu7GRNqgWHlvH3yqGeCbreWYrYVSrluEpBu6807cp3zDxrU+autOnsewm5+md
ka3DdqrbxJSblYK8fJKESAUgkRmZgYKbgl0iiCuqX+ib6I4OA3Z68ny7dl0fY3Ws
vwt7d88SaBKDdJmUZyb/sm4aJsW69GN+ECZolxrn4TIw45k4tes2s6Ma5+TV3E9h
Fd1RuqduFEqQ7cj31UPe2x8rgj5Fo5nbjCWxdZv+/3zF8+cHwi8iwkp2PScsPCsa
fmCdehUE5DrgobsRNANe6XJzxY5wp2VNpGEWKeaQz2Z0/d9T1YFS7a8aewvhXoPC
isZboi6GQh2XoE8UgGJa29VUuaIkUW513DwCGw8mz1yKN+kHGcsRXXjkjaZoQn3U
MMvh/zkI2Hpy/m2R8PWeIq5XhLJvmlZ19JJzUHJIjXh9Fn9EVtXhlUleh6mzMfeM
n8NOg7Eukep2sBgmaufkUKz2Jtogs59YDSXZEvqJjIkPM2Wi0hA18Qj+pilES1ff
3ckk3mxY
=8D3Q
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
After removal of the legacy EEPROM driver and I2C_CLASS_DDC support in
olpc_dcon there's no i2c client driver left supporting I2C_CLASS_DDC.
Class-based device auto-detection is a legacy mechanism and shouldn't
be used in new code. So we can remove this class completely now.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The current way of calculating the pbn_div value, the link BW per each
MTP slot, worked only for DP 1.4 link rates. Fix things up for UHBR
rates calculating with the correct channel coding efficiency based on
the link rate.
v2:
- Return the fractional pbn_div value from drm_dp_get_vc_payload_bw().
v3:
- Fix rounding up quotient while calculating req_slots. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231117150929.1767227-1-imre.deak@intel.com
On UHBR links the PBN divider is a fractional number, accordingly store
it in fixed point format. For now drm_dp_get_vc_payload_bw() always
returns a whole number and all callers will use only the integer part of
it which should preserve the current behavior. The next patch will fix
drm_dp_get_vc_payload_bw() for UHBR rates returning a fractional number
for those (also accounting for the channel coding efficiency correctly).
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Wayne Lin <wayne.lin@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[Rebased changes in dm_helpers_construct_old_payload() on drm-intel-next]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-2-imre.deak@intel.com
Add helpers drivers can use to calculate the BW allocation overhead -
due to SSC, FEC, DSC and data alignment on symbol cycles - and the
channel coding efficiency - due to the 8b/10b, 128b/132b encoding. On
128b/132b links the FEC overhead is part of the coding efficiency, so
not accounted for in the BW allocation overhead.
The drivers can use these functions to calculate a ratio, controlling
the stream symbol insertion rate of the source device in each SST TU
or MST MTP frame. Drivers can calculate this
m/n = (pixel_data_rate * drm_dp_bw_overhead()) /
(link_data_rate * drm_dp_bw_channel_coding_efficiency())
ratio for a given link and pixel stream and with that the
slots_per_mtp = CEIL(64 * m / n)
allocated slots per MTP for the stream in a link frame and with
that the
pbn = slots_per_mtp * drm_mst_get_pbn_divider()
allocated PBNs for the stream on the MST link path.
Take drm_dp_bw_overhead() into use in drm_dp_calc_pbn_mode(), for
drivers calculating the PBN value directly.
v2:
- Add dockbook description to drm_dp_bw_channel_coding_efficiency().
(LKP).
- Clarify the way m/n ratio is calculated in the commit log.
v3:
- Fix compile breakage for !CONFIG_BACKLIGHT_CLASS_DEVICE. (LKP)
- Account for FEC_PM overhead (+ 0.0015625 %), add comment
with the formula to calculate the total FEC overhead. (Ville)
v4:
- Rename DRM_DP_OVERHEAD_SSC to DRM_DP_OVERHEAD_SSC_REF_CLK. (Ville)
v5:
- Clarify in the commit log what MTP means.
- Simplify the commit log's formula to calculate PBN.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: kernel test robot <lkp@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v2)
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107001505.3370108-1-imre.deak@intel.com
Add a quirk for Synaptics MST hubs, which require a workaround - at leat
on i915 - for some modes, on which the hub applies HBLANK expansion.
These modes will only work by enabling DSC decompression for them, a
follow-up patch will do this in i915.
v2:
- Fix the quirk name in its DocBook description.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-9-imre.deak@intel.com
The Synaptics MST branch devices support DSC decompression on all their
output ports, provided that they are last branch devices (with their
output ports connected to the sinks). The Thinkpad 40B0 TBT dock for
instance has two such branch devices, a secondary one connected to one
of the output ports of the primary; hence the decompression needs to be
enabled in both branch devices to enable decompression for all the
sinks.
Based on the above add support for enabling decompression in last
Synaptics branch devices.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-7-imre.deak@intel.com
drm_dp_mst_atomic_check_mgr() should check for BW limitation starting
from sink ports continuing towards the root port, so that drivers can
use the @failing_port returned to resolve a BW overallocation in an
ideal way. For instance from streams A,B,C in a topology A,B going
through @failing_port and C not going through it, a BW overallocation of
A,B due to a limit of the port must be resolved first before considering
the limits of other ports closer to the root port. This way can avoid
reducing the BW of stream C unnecessarily due to a BW limit closer to the
root port.
Based on the above swap the order of the BW check for the root port and
the check for all the ports downstream of it (the latter going through
the topology already in the sink->root port direction).
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-6-imre.deak@intel.com
Factor out a helper to check the atomic state for one MST topology
manager, returning the MST port where the BW limit check has failed.
This will be used in a follow-up patch by the i915 driver to improve the
BW sharing between MST streams.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-5-imre.deak@intel.com
The current code does '(bpp << 4) / 16' in the MST PBN
calculation, but that is just the same as 'bpp' so the
DSC codepath achieves absolutely nothing. Fix it up so that
the fractional part of the bpp value is actually used instead
of truncated away. 64*1006 has enough zero lsbs that we can
just shift that down in the dividend and thus still manage
to stick to a 32bit divisor.
And while touching this, let's just make the whole thing more
straightforward by making the passed in bpp value .4 binary
fixed point always, instead of having to pass in different
things based on whether DSC is enabled or not.
v2:
- Fix DSC kunit test cases.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: dc48529fb1 ("drm/dp_mst: Add PBN calculation for DSC modes")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Imre: Fix kunit test cases]
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-3-imre.deak@intel.com
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEEKbZHaGwW9KfbeusDHTzWXnEhr4FAmVAgzYACgkQDHTzWXnE
hr7ZEQ//UXne3tyGOsU3X8r+lstLFDMa90a3hvTg6hX+Q0MjHd/clwkKFkLpkipL
n7gIZlaHl11dRs0FzrIZA5EVAAgjMLKmIl10NBDFec6ZFA3VERcggx8y61uifI15
VviMR1VbLHYZaCdyrQOK0A4wcktWnKXyoXp7cwy9crdc2GOBMUZkdIqtvD7jHxQx
UMIFnzi1CyKUX/Fjt/JceYcNk9y2ZGkzakYO3sHcUdv4DPu9qX4kNzpjF691AZBP
UeKWvCswTRVg2M0kuo/RYIBzqaTmOlk6dHLWBognIeZPyuyhCcaGC2d64c6tShwQ
dtHdi+IgyQ8s2qb350ymKTQUP7xA/DfZBwH7LvrZALBxeQGYQN1CnsgDMOS2wcUc
XrRFiS7PxEOtMMBctcPBnnoV5ttnsLLlPpzM9puh9sUFMn6CgLzcAMqXdqxzMajH
+dz2aD1N0vMqq4varozOg9SC2QamgUiPN/TQfrulhCTCfQaXczy5x1OYiIz65+Sl
mKoe2WASuP9Ve8do4N/wEwH5SZY2ItipBdUTRxttY9NTanmV0X5DjZBXH5b9XGci
Zl5Ar613f9zwm5T5BVA5k6s3ZbGY6QcP5pDNTCPaSgitfFXIdReBZ2CaYzK3MPg/
Wit/TXrud9yT6VPpI1igboMyasf5QubV1MY1K83kOCWr9u8R2CM=
=l79u
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Highlights:
- AMD adds some more upcoming HW platforms
- Intel made Meteorlake stable and started adding Lunarlake
- nouveau has a bunch of display rework in prepartion for the NVIDIA
GSP firmware support
- msm adds a7xx support
- habanalabs has finished migration to accel subsystem
Detail summary:
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver"
* tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm: (1803 commits)
drm/amdgpu: Remove unused variables from amdgpu_show_fdinfo
drm/amdgpu: Remove duplicate fdinfo fields
drm/amd/amdgpu: avoid to disable gfxhub interrupt when driver is unloaded
drm/amdgpu: Add EXT_COHERENT support for APU and NUMA systems
drm/amdgpu: Retrieve CE count from ce_count_lo_chip in EccInfo table
drm/amdgpu: Identify data parity error corrected in replay mode
drm/amdgpu: Fix typo in IP discovery parsing
drm/amd/display: fix S/G display enablement
drm/amdxcp: fix amdxcp unloads incompletely
drm/amd/amdgpu: fix the GPU power print error in pm info
drm/amdgpu: Use pcie domain of xcc acpi objects
drm/amd: check num of link levels when update pcie param
drm/amdgpu: Add a read to GFX v9.4.3 ring test
drm/amd/pm: call smu_cmn_get_smc_version in is_mode1_reset_supported.
drm/amdgpu: get RAS poison status from DF v4_6_2
drm/amdgpu: Use discovery table's subrevision
drm/amd/display: 3.2.256
drm/amd/display: add interface to query SubVP status
drm/amd/display: Read before writing Backlight Mode Set Register
drm/amd/display: Disable SYMCLK32_SE RCO on DCN314
...
As drm_dp_get_mst_branch_device_by_guid() is called from
drm_dp_get_mst_branch_device_by_guid(), mstb parameter has to be checked,
otherwise NULL dereference may occur in the call to
the memcpy() and cause following:
[12579.365869] BUG: kernel NULL pointer dereference, address: 0000000000000049
[12579.365878] #PF: supervisor read access in kernel mode
[12579.365880] #PF: error_code(0x0000) - not-present page
[12579.365882] PGD 0 P4D 0
[12579.365887] Oops: 0000 [#1] PREEMPT SMP NOPTI
...
[12579.365895] Workqueue: events_long drm_dp_mst_up_req_work
[12579.365899] RIP: 0010:memcmp+0xb/0x29
[12579.365921] Call Trace:
[12579.365927] get_mst_branch_device_by_guid_helper+0x22/0x64
[12579.365930] drm_dp_mst_up_req_work+0x137/0x416
[12579.365933] process_one_work+0x1d0/0x419
[12579.365935] worker_thread+0x11a/0x289
[12579.365938] kthread+0x13e/0x14f
[12579.365941] ? process_one_work+0x419/0x419
[12579.365943] ? kthread_blkcg+0x31/0x31
[12579.365946] ret_from_fork+0x1f/0x30
As get_mst_branch_device_by_guid_helper() is recursive, moving condition
to the first line allow to remove a similar one for step over of NULL elements
inside a loop.
Fixes: 5e93b8208d ("drm/dp/mst: move GUID storage from mgr, port to only mst branch")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Reviewed-by: Radoslaw Biernacki <rad@chromium.org>
Signed-off-by: Manasi Navare <navaremanasi@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922063410.23626-1-lma@semihalf.com
Return an error during payload addition if the payload port isn't
found. This shouldn't change the behavior since only the i915 driver
checks the return value, printing an error message in case of a failure.
While at it simplify the control flow.
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230913223218.540365-2-imre.deak@intel.com
[Why]
Today, the allocation/deallocation steps and status is a bit unclear.
For instance, payload->vc_start_slot = -1 stands for "the failure of
updating DPCD payload ID table" and can also represent as "payload is not
allocated yet". These two cases should be handled differently and hence
better to distinguish them for better understanding.
[How]
Define enumeration - ALLOCATION_LOCAL, ALLOCATION_DFP and ALLOCATION_REMOTE
to distinguish different allocation status. Adjust the code to handle
different status accordingly for better understanding the sequence of
payload allocation and payload removement.
For payload creation, the procedure should look like this:
DRM part 1:
* step 1 - update sw mst mgr variables to add a new payload
* step 2 - add payload at immediate DFP DPCD payload table
Driver:
* Add new payload in HW and sync up with DFP by sending ACT
DRM Part 2:
* Send ALLOCATE_PAYLOAD sideband message to allocate bandwidth along the
virtual channel.
And as for payload removement, the procedure should look like this:
DRM part 1:
* step 1 - Send ALLOCATE_PAYLOAD sideband message to release bandwidth
along the virtual channel
* step 2 - Clear payload allocation at immediate DFP DPCD payload table
Driver:
* Remove the payload in HW and sync up with DFP by sending ACT
DRM part 2:
* update sw mst mgr variables to remove the payload
Note that it's fine to fail when communicate with the branch device
connected at immediate downstrean-facing port, but updating variables of
SW mst mgr and HW configuration should be conducted anyway. That's because
it's under commit_tail and we need to complete the HW programming.
Changes since v1:
* Remove the set but not use variable 'old_payload' in function
'nv50_msto_prepare'. Catched by kernel test robot <lkp@intel.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230807025639.1612361-3-Wayne.Lin@amd.com
[Why]
There is no need to consider payload->delete case since we won't call
drm_dp_add_payload_part2() to create a payload when we're about to
remove it.
[How]
Delete unnecessary case to simplify the code.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230807025639.1612361-2-Wayne.Lin@amd.com
Connectors have source physical address available in display
info. There's no need to parse the EDID again for this. Add
drm_dp_cec_attach() to do this.
Seems like the set_edid/unset_edid naming is a bit specific now that
there's no need to pass the EDID at all, so aim for attach/detach going
forward.
v2: Fix the embarrashing build failures
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: linux-media@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825130120.1250089-1-jani.nikula@intel.com
As per DP v1.4, a DP DSC Sink device shall support 8bpc in DPCD 6Ah.
Apparently some panels that do support DSC, are not setting the bit for
8bpc.
So always assume 8bpc support by DSC decoder, when DSC is claimed to be
supported.
v2: Use helper to get check dsc support. (Ankit)
v3: Fix styling and other typos. (Jani)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230824125121.840298-2-ankit.k.nautiyal@intel.com
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmSvvRAACgkQaA3BHVML
eiNpGQgAs8jq1XjN9t8jZsdgXnoCbkZyVUI2NO0HwoVwpRCLgbXp5AX5qq2oRciE
TBhe4Fceh/ZsYqHTZQahnguxgRKM5JgXwbI4Z0iiOVcqasNbycaKAqipxJJ7kdo1
qPhGCbgQFVX7oIq2xjfXehh6O0SYX+R9r88X8dMJxMYv/pcLwOHG74kS040WOcQq
uATgcnobOf/D8ZmlqvfKGAeTUoFo/RSR2Uhlauka58qgeUbicrTELZT2barY9d+k
as6U5vv4wx2zMklTkjrlkMpAT1ZpbB9d3jGHwL27VEnjlfd3wV2bdH7Dzn9qZRf/
gn0ALg/b3u5yBWk/k7YBvijXyNcH6Q==
=bBuG
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-07-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.6:
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713090830.GA23281@linux-uq9g
core:
- replace strlcpy with strscpy
- EDID changes to support further conversion to struct drm_edid
- Move i915 DSC parameter code to common DRM helpers
- Add Colorspace functionality
aperture:
- ignore framebuffers with non-primary devices
fbdev:
- use fbdev i/o helpers
- add Kconfig options for fb_ops helpers
- use new fb io helpers directly in drivers
sysfs:
- export DRM connector ID
scheduler:
- Avoid an infinite loop
ttm:
- store function table in .rodata
- Add query for TTM mem limit
- Add NUMA awareness to pools
- Export ttm_pool_fini()
bridge:
- fsl-ldb: support i.MX6SX
- lt9211, lt9611: remove blanking packets
- tc358768: implement input bus formats, devm cleanups
- ti-snd65dsi86: implement wait_hpd_asserted
- analogix: fix endless probe loop
- samsung-dsim: support swapped clock, fix enabling, support var clock
- display-connector: Add support for external power supply
- imx: Fix module linking
- tc358762: Support reset GPIO
panel:
- nt36523: Support Lenovo J606F
- st7703: Support Anbernic RG353V-V2
- InnoLux G070ACE-L01 support
- boe-tv101wum-nl6: Improve initialization
- sharp-ls043t1le001: Mode fixes
- simple: BOE EV121WXM-N10-1850, S6D7AA0
- Ampire AM-800480L1TMQW-T00H
- Rocktech RK043FN48H
- Starry himax83102-j02
- Starry ili9882t
amdgpu:
- add new ctx query flag to handle reset better
- add new query/set shadow buffer for rdna3
- DCN 3.2/3.1.x/3.0.x updates
- Enable DC_FP on loongarch
- PCIe fix for RDNA2
- improve DC FAMS/SubVP support for better power management
- partition support for lots of engines
- Take NUMA into account when allocating memory
- Add new DRM_AMDGPU_WERROR config parameter to help with CI
- Initial SMU13 overdrive support
- Add support for new colorspace KMS API
- W=1 fixes
amdkfd:
- Query TTM mem limit rather than hardcoding it
- GC 9.4.3 partition support
- Handle NUMA for partitions
- Add debugger interface for enabling gdb
- Add KFD event age tracking
radeon:
- Fix possible UAF
i915:
- new getparam for PXP support
- GSC/MEI proxy driver
- Meteorlake display enablement
- avoid clearing preallocated framebuffers with TTM
- implement framebuffer mmap support
- Disable sampler indirect state in bindless heap
- Enable fdinfo for GuC backends
- GuC loading and firmware table handling fixes
- Various refactors for multi-tile enablement
- Define MOCS and PAT tables for MTL
- GSC/MEI support for Meteorlake
- PMU multi-tile support
- Large driver kernel doc cleanup
- Allow VRR toggling and arbitrary refresh rates
- Support async flips on linear buffers on display ver 12+
- Expose CRTC CTM property on ILK/SNB/VLV
- New debugfs for display clock frequencies
- Hotplug refactoring
- Display refactoring
- I915_GEM_CREATE_EXT_SET_PAT for Mesa on Meteorlake
- Use large rings for compute contexts
- HuC loading for MTL
- Allow user to set cache at BO creation
- MTL powermanagement enhancements
- Switch to dedicated workqueues to stop using flush_scheduled_work()
- Move display runtime init under display/
- Remove 10bit gamma on desktop gen3 parts, they don't support it
habanalabs:
- uapi: return 0 for user queries if there was a h/w or f/w error
- Add pci health check when we lose connection with the firmware. This can be used to
distinguish between pci link down and firmware getting stuck.
- Add more info to the error print when TPC interrupt occur.
- Firmware fixes
msm:
- Adreno A660 bindings
- SM8350 MDSS bindings fix
- Added support for DPU on sm6350 and sm6375 platforms
- Implemented tearcheck support to support vsync on SM150 and newer platforms
- Enabled missing features (DSPP, DSC, split display) on sc8180x, sc8280xp, sm8450
- Added support for DSI and 28nm DSI PHY on MSM8226 platform
- Added support for DSI on sm6350 and sm6375 platforms
- Added support for display controller on MSM8226 platform
- A690 GPU support
- Move cmdstream dumping out of fence signaling path
- a610 support
- Support for a6xx devices without GMU
nouveau:
- NULL ptr before deref fixes
armada:
- implement fbdev emulation as client
sun4i:
- fix mipi-dsi dotclock
- release clocks
vc4:
- rgb range toggle property
- BT601 / BT2020 HDMI support
vkms:
- convert to drmm helpers
- add reflection and rotation support
- fix rgb565 conversion
gma500:
- fix iomem access
shmobile:
- support renesas soc platform
- enable fbdev
mxsfb:
- Add support for i.MX93 LCDIF
stm:
- dsi: Use devm_ helper
- ltdc: Fix potential invalid pointer deref
renesas:
- Group drivers in renesas subdirectory to prepare for new platform
- Drop deprecated R-Car H3 ES1.x support
meson:
- Add support for MIPI DSI displays
virtio:
- add sync object support
mediatek:
- Add display binding document for MT6795
-----BEGIN PGP SIGNATURE-----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=FmUA
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-06-29' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"There is one set of patches to misc for a i915 gsc/mei proxy driver.
Otherwise it's mostly amdgpu/i915/msm, lots of hw enablement and lots
of refactoring.
core:
- replace strlcpy with strscpy
- EDID changes to support further conversion to struct drm_edid
- Move i915 DSC parameter code to common DRM helpers
- Add Colorspace functionality
aperture:
- ignore framebuffers with non-primary devices
fbdev:
- use fbdev i/o helpers
- add Kconfig options for fb_ops helpers
- use new fb io helpers directly in drivers
sysfs:
- export DRM connector ID
scheduler:
- Avoid an infinite loop
ttm:
- store function table in .rodata
- Add query for TTM mem limit
- Add NUMA awareness to pools
- Export ttm_pool_fini()
bridge:
- fsl-ldb: support i.MX6SX
- lt9211, lt9611: remove blanking packets
- tc358768: implement input bus formats, devm cleanups
- ti-snd65dsi86: implement wait_hpd_asserted
- analogix: fix endless probe loop
- samsung-dsim: support swapped clock, fix enabling, support var
clock
- display-connector: Add support for external power supply
- imx: Fix module linking
- tc358762: Support reset GPIO
panel:
- nt36523: Support Lenovo J606F
- st7703: Support Anbernic RG353V-V2
- InnoLux G070ACE-L01 support
- boe-tv101wum-nl6: Improve initialization
- sharp-ls043t1le001: Mode fixes
- simple: BOE EV121WXM-N10-1850, S6D7AA0
- Ampire AM-800480L1TMQW-T00H
- Rocktech RK043FN48H
- Starry himax83102-j02
- Starry ili9882t
amdgpu:
- add new ctx query flag to handle reset better
- add new query/set shadow buffer for rdna3
- DCN 3.2/3.1.x/3.0.x updates
- Enable DC_FP on loongarch
- PCIe fix for RDNA2
- improve DC FAMS/SubVP support for better power management
- partition support for lots of engines
- Take NUMA into account when allocating memory
- Add new DRM_AMDGPU_WERROR config parameter to help with CI
- Initial SMU13 overdrive support
- Add support for new colorspace KMS API
- W=1 fixes
amdkfd:
- Query TTM mem limit rather than hardcoding it
- GC 9.4.3 partition support
- Handle NUMA for partitions
- Add debugger interface for enabling gdb
- Add KFD event age tracking
radeon:
- Fix possible UAF
i915:
- new getparam for PXP support
- GSC/MEI proxy driver
- Meteorlake display enablement
- avoid clearing preallocated framebuffers with TTM
- implement framebuffer mmap support
- Disable sampler indirect state in bindless heap
- Enable fdinfo for GuC backends
- GuC loading and firmware table handling fixes
- Various refactors for multi-tile enablement
- Define MOCS and PAT tables for MTL
- GSC/MEI support for Meteorlake
- PMU multi-tile support
- Large driver kernel doc cleanup
- Allow VRR toggling and arbitrary refresh rates
- Support async flips on linear buffers on display ver 12+
- Expose CRTC CTM property on ILK/SNB/VLV
- New debugfs for display clock frequencies
- Hotplug refactoring
- Display refactoring
- I915_GEM_CREATE_EXT_SET_PAT for Mesa on Meteorlake
- Use large rings for compute contexts
- HuC loading for MTL
- Allow user to set cache at BO creation
- MTL powermanagement enhancements
- Switch to dedicated workqueues to stop using flush_scheduled_work()
- Move display runtime init under display/
- Remove 10bit gamma on desktop gen3 parts, they don't support it
habanalabs:
- uapi: return 0 for user queries if there was a h/w or f/w error
- Add pci health check when we lose connection with the firmware.
This can be used to distinguish between pci link down and firmware
getting stuck.
- Add more info to the error print when TPC interrupt occur.
- Firmware fixes
msm:
- Adreno A660 bindings
- SM8350 MDSS bindings fix
- Added support for DPU on sm6350 and sm6375 platforms
- Implemented tearcheck support to support vsync on SM150 and newer
platforms
- Enabled missing features (DSPP, DSC, split display) on sc8180x,
sc8280xp, sm8450
- Added support for DSI and 28nm DSI PHY on MSM8226 platform
- Added support for DSI on sm6350 and sm6375 platforms
- Added support for display controller on MSM8226 platform
- A690 GPU support
- Move cmdstream dumping out of fence signaling path
- a610 support
- Support for a6xx devices without GMU
nouveau:
- NULL ptr before deref fixes
armada:
- implement fbdev emulation as client
sun4i:
- fix mipi-dsi dotclock
- release clocks
vc4:
- rgb range toggle property
- BT601 / BT2020 HDMI support
vkms:
- convert to drmm helpers
- add reflection and rotation support
- fix rgb565 conversion
gma500:
- fix iomem access
shmobile:
- support renesas soc platform
- enable fbdev
mxsfb:
- Add support for i.MX93 LCDIF
stm:
- dsi: Use devm_ helper
- ltdc: Fix potential invalid pointer deref
renesas:
- Group drivers in renesas subdirectory to prepare for new platform
- Drop deprecated R-Car H3 ES1.x support
meson:
- Add support for MIPI DSI displays
virtio:
- add sync object support
mediatek:
- Add display binding document for MT6795"
* tag 'drm-next-2023-06-29' of git://anongit.freedesktop.org/drm/drm: (1791 commits)
drm/i915: Fix a NULL vs IS_ERR() bug
drm/i915: make i915_drm_client_fdinfo() reference conditional again
drm/i915/huc: Fix missing error code in intel_huc_init()
drm/i915/gsc: take a wakeref for the proxy-init-completion check
drm/msm/a6xx: Add A610 speedbin support
drm/msm/a6xx: Add A619_holi speedbin support
drm/msm/a6xx: Use adreno_is_aXYZ macros in speedbin matching
drm/msm/a6xx: Use "else if" in GPU speedbin rev matching
drm/msm/a6xx: Fix some A619 tunables
drm/msm/a6xx: Add A610 support
drm/msm/a6xx: Add support for A619_holi
drm/msm/adreno: Disable has_cached_coherent in GMU wrapper configurations
drm/msm/a6xx: Introduce GMU wrapper support
drm/msm/a6xx: Move CX GMU power counter enablement to hw_init
drm/msm/a6xx: Extend and explain UBWC config
drm/msm/a6xx: Remove both GBIF and RBBM GBIF halt on hw init
drm/msm/a6xx: Add a helper for software-resetting the GPU
drm/msm/a6xx: Improve a6xx_bus_clear_pending_transactions()
drm/msm/a6xx: Move a6xx_bus_clear_pending_transactions to a6xx_gpu
drm/msm/a6xx: Move force keepalive vote removal to a6xx_gmu_force_off()
...
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members
-----BEGIN PGP SIGNATURE-----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=s0j1
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"There are three areas of note:
A bunch of strlcpy()->strscpy() conversions ended up living in my tree
since they were either Acked by maintainers for me to carry, or got
ignored for multiple weeks (and were trivial changes).
The compiler option '-fstrict-flex-arrays=3' has been enabled
globally, and has been in -next for the entire devel cycle. This
changes compiler diagnostics (though mainly just -Warray-bounds which
is disabled) and potential UBSAN_BOUNDS and FORTIFY _warning_
coverage. In other words, there are no new restrictions, just
potentially new warnings. Any new FORTIFY warnings we've seen have
been fixed (usually in their respective subsystem trees). For more
details, see commit df8fc4e934.
The under-development compiler attribute __counted_by has been added
so that we can start annotating flexible array members with their
associated structure member that tracks the count of flexible array
elements at run-time. It is possible (likely?) that the exact syntax
of the attribute will change before it is finalized, but GCC and Clang
are working together to sort it out. Any changes can be made to the
macro while we continue to add annotations.
As an example of that last case, I have a treewide commit waiting with
such annotations found via Coccinelle:
https://git.kernel.org/linus/adc5b3cb48a049563dc673f348eab7b6beba8a9b
Also see commit dd06e72e68 for more details.
Summary:
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex
arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members"
* tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (54 commits)
netfilter: ipset: Replace strlcpy with strscpy
uml: Replace strlcpy with strscpy
um: Use HOST_DIR for mrproper
kallsyms: Replace all non-returning strlcpy with strscpy
sh: Replace all non-returning strlcpy with strscpy
of/flattree: Replace all non-returning strlcpy with strscpy
sparc64: Replace all non-returning strlcpy with strscpy
Hexagon: Replace all non-returning strlcpy with strscpy
kobject: Use return value of strreplace()
lib/string_helpers: Change returned value of the strreplace()
jbd2: Avoid printing outside the boundary of the buffer
checkpatch: Check for 0-length and 1-element arrays
riscv/purgatory: Do not use fortified string functions
s390/purgatory: Do not use fortified string functions
x86/purgatory: Do not use fortified string functions
acpi: Replace struct acpi_table_slit 1-element array with flex-array
clocksource: Replace all non-returning strlcpy with strscpy
string: use __builtin_memcpy() in strlcpy/strlcat
staging: most: Replace all non-returning strlcpy with strscpy
drm/i2c: tda998x: Replace all non-returning strlcpy with strscpy
...
Rename drm_sysfs_connector_status_event() to
drm_sysfs_connector_property_event(). Indeed, "status" is a bit
vague: it can easily be confused with the connected/disconnected
status of the connector. This function has nothing to do with
connected/disconnected: it merely sends a notification that a
connector's property has changed (e.g. HDCP, privacy screen, etc).
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Manasi Navare <navaremanasi@chromium.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230620174231.260335-1-contact@emersion.fr
I've been experiencing some intermittent crashes down in the display
driver code. The symptoms are ususally a line like this in dmesg:
amdgpu 0000:30:00.0: [drm] Failed to create MST payload for port 000000006d3a3885: -5
...followed by an Oops due to a NULL pointer dereference.
Switch to using mgr->dev instead of state->dev since "state" can be
NULL in some cases.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2184855
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230419112447.18471-1-jlayton@kernel.org
Updates for v6.5.. this includes a backmerg of drm-next tree to be able
to use new DRM DSC helpers.
Core:
+ Add Marijn Suijten as drm/msm reviewer
+ Adreno A660 bindings
+ SM8350 MDSS bindings fix
+ Fix adreno_is_a690() warnings
+ More generic (DRM) and MSM-specific DSC helpers
DP:
+ Removed obsolete USB-PD remains
+ Documented DP compatible string for sm8550 platform
DPU:
+ Enable missing features (DSPP, DSC, split display) on sc8180x,
sc8280xp, sm8450
+ Enabled writeback on sc7280
+ Implemented tearcheck support to support vsync on SM150 and
newer platforms
+ Native HDMI output support
+ Dropped unused features: regdma, GC, IGC
+ Fixed the DSC flush operations
+ Simplified QoS handling, removing obsolete and unused features
and merging SSPP and WB code paths
+ Reworked dpu_encoder initialisation path
+ Enabled DSPP support on sdm845
+ Disabled color-management if DSPP blocks are not available
+ Added support for DSC 1.2 blocks found on sm8350 and later
+ Added .fb_dirty to fix CMD panels
DSI:
+ Drop powerup quirks in favour of using pre_enable_prev_first for
downstream bridges
+ Fixed 14nm DSI PHY programming
+ Added support for DSI and 28nm DSI PHY on MSM8226 platform
+ Make use of DRM and MSM DSC helpers
MDP5:
+ Added support for display controller on MSM8226 platform
GPU:
+ A690 support
+ Don't set IO_PGTABLE_QUIRK_ARM_OUTER_WBWA on devices with coherent SMMU
(like A690)
+ Move cmdstream dumping out of fence signaling path
+ Cleanups
+ Support for a6xx devices without GMU (aka "GMU wrapper"
+ a610 support
+ a619_holi support (a619 variant without GMU)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsUB=tRB4nR6ZCJMuLhro5zN3BQWUSywVYbaipqqDZ_cQ@mail.gmail.com
[Why]
The sequence for collecting down_reply from source perspective should
be:
Request_n->repeat (get partial reply of Request_n->clear message ready
flag to ack DPRX that the message is received) till all partial
replies for Request_n are received->new Request_n+1.
Now there is chance that drm_dp_mst_hpd_irq() will fire new down
request in the tx queue when the down reply is incomplete. Source is
restricted to generate interveleaved message transactions so we should
avoid it.
Also, while assembling partial reply packets, reading out DPCD DOWN_REP
Sideband MSG buffer + clearing DOWN_REP_MSG_RDY flag should be
wrapped up as a complete operation for reading out a reply packet.
Kicking off a new request before clearing DOWN_REP_MSG_RDY flag might
be risky. e.g. If the reply of the new request has overwritten the
DPRX DOWN_REP Sideband MSG buffer before source writing one to clear
DOWN_REP_MSG_RDY flag, source then unintentionally flushes the reply
for the new request. Should handle the up request in the same way.
[How]
Separete drm_dp_mst_hpd_irq() into 2 steps. After acking the MST IRQ
event, driver calls drm_dp_mst_hpd_irq_send_new_request() and might
trigger drm_dp_mst_kick_tx() only when there is no on going message
transaction.
Changes since v1:
* Reworked on review comments received
-> Adjust the fix to let driver explicitly kick off new down request
when mst irq event is handled and acked
-> Adjust the commit message
Changes since v2:
* Adjust the commit message
* Adjust the naming of the divided 2 functions and add a new input
parameter "ack".
* Adjust code flow as per review comments.
Changes since v3:
* Update the function description of drm_dp_mst_hpd_irq_handle_event
Changes since v4:
* Change ack of drm_dp_mst_hpd_irq_handle_event() to be an array align
the size of esi[]
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a helper setting config values which are typically constant across
operating modes (table E-4 of the standard) and mux_word_size (which is
a const according to 3.5.2).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/539280/
Link: https://lore.kernel.org/r/20230329-rfc-msm-dsc-helper-v14-2-bafc7be95691@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Convert the topology manager to use struct drm_edid, add
drm_dp_mst_edid_read() that returns drm_edid, and rewrite the old
drm_dp_mst_get_edid() to use it.
Note that the old drm_get_edid() ended up calling
drm_connector_update_edid_property(). This responsibility is now
deferred to drivers, which all do it anyway after calling
drm_dp_mst_edid_read() or drm_dp_mst_get_edid().
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c32e5c241934093fc4144eed4c01155e1f03af1.1685437501.git.jani.nikula@intel.com
DSC model contains pre-SCR RC parameters for other bpp/bpc combinations,
include them here for completeness. The values were generated from the
'pre_scr_cfg_files_for_reference' files found in DSC models 20210623.
The same fileset is a part of DSC model 20161212.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-8-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
The array of rc_parameters contains a mixture of parameters from DSC 1.1
and DSC 1.2 standards. Split these tow configuration arrays in
preparation to adding more configuration data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Suraj Kandpal
Reviewed-by: Suraj Kandpal
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-7-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
Next commits are going to add support for additional RC parameter lookup
tables. These tables are going to use different bpp/bpc combinations,
thus it makes little sense to keep the 2d array for RC parameters.
Switch to using the flat array.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-6-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
Move DSC RC tables to DRM DSC helper. No additional code changes
and/or cleanups are a part of this commit, it will be cleaned up in the
followup commits.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-4-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
The rc_buf_thresh values are common to all DSC implementations. Move
them to the common helper together with the code to propagate them to
the drm_dsc_config.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-3-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
Include the device and connector information in the SCDC
debugs. Makes it easier to figure out who did what.
v2: Rely on connector->ddc (Maxime)
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403223652.18848-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EDID of an HDR display defines EOTFs that are supported
by the display and can be set in the HDR metadata infoframe.
Userspace is expected to read the EDID and set an appropriate
HDR_OUTPUT_METADATA.
In drm_parse_hdr_metadata_block the kernel reads the supported
EOTFs from the EDID and stores them in the
drm_connector->hdr_sink_metadata. While doing so it also
filters the EOTFs to the EOTFs the kernel knows about.
When an HDR_OUTPUT_METADATA is set it then checks to
make sure the EOTF is a supported EOTF. In cases where
the kernel doesn't know about a new EOTF this check will
fail, even if the EDID advertises support.
Since it is expected that userspace reads the EDID to understand
what the display supports it doesn't make sense for DRM to block
an HDR_OUTPUT_METADATA if it contains an EOTF the kernel doesn't
understand.
This comes with the added benefit of future-proofing metadata
support. If the spec defines a new EOTF there is no need to
update DRM and an compositor can immediately make use of it.
Bug: https://gitlab.freedesktop.org/wayland/weston/-/issues/609
v2: Distinguish EOTFs defind in kernel and ones defined
in EDID in the commit description (Pekka)
v3: Rebase; drm_hdmi_infoframe_set_hdr_metadata moved
to drm_hdmi_helper.c
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Sebastian Wick <sebastian.wick@redhat.com>
Cc: Vitaly.Prosyak@amd.com
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-By: Joshua Ashton <joshua@froggi.es>
Link: https://patchwork.freedesktop.org/patch/msgid/20230113162428.33874-2-harry.wentland@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The EDID of an HDR display defines EOTFs that are supported
by the display and can be set in the HDR metadata infoframe.
Userspace is expected to read the EDID and set an appropriate
HDR_OUTPUT_METADATA.
In drm_parse_hdr_metadata_block the kernel reads the supported
EOTFs from the EDID and stores them in the
drm_connector->hdr_sink_metadata. While doing so it also
filters the EOTFs to the EOTFs the kernel knows about.
When an HDR_OUTPUT_METADATA is set it then checks to
make sure the EOTF is a supported EOTF. In cases where
the kernel doesn't know about a new EOTF this check will
fail, even if the EDID advertises support.
Since it is expected that userspace reads the EDID to understand
what the display supports it doesn't make sense for DRM to block
an HDR_OUTPUT_METADATA if it contains an EOTF the kernel doesn't
understand.
This comes with the added benefit of future-proofing metadata
support. If the spec defines a new EOTF there is no need to
update DRM and an compositor can immediately make use of it.
Bug: https://gitlab.freedesktop.org/wayland/weston/-/issues/609
v2: Distinguish EOTFs defind in kernel and ones defined
in EDID in the commit description (Pekka)
v3: Rebase; drm_hdmi_infoframe_set_hdr_metadata moved
to drm_hdmi_helper.c
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Sebastian Wick <sebastian.wick@redhat.com>
Cc: Vitaly.Prosyak@amd.com
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-By: Joshua Ashton <joshua@froggi.es>
Link: https://patchwork.freedesktop.org/patch/msgid/20230113162428.33874-2-harry.wentland@amd.com
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Add a function to get the old MST topology state, required by a
follow-up i915 patch.
While at it clarify the code comment of
drm_atomic_get_new_mst_topology_state() and add _new prefix
to the new state pointer to remind about its difference from the old
state.
v2: Use old_/new_ prefixes for the state pointers. (Ville)
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org # 6.1
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206114856.2665066-3-imre.deak@intel.com
Atm, drm_dp_remove_payload() uses the same payload state to both get the
vc_start_slot required for the payload removal DPCD message and to
deduct time_slots from vc_start_slot of all payloads after the one being
removed.
The above isn't always correct, as vc_start_slot must be the up-to-date
version contained in the new payload state, but time_slots must be the
one used when the payload was previously added, contained in the old
payload state. The new payload's time_slots can change vs. the old one
if the current atomic commit changes the corresponding mode.
This patch let's drivers pass the old and new payload states to
drm_dp_remove_payload(), but keeps these the same for now in all drivers
not to change the behavior. A follow-up i915 patch will pass in that
driver the correct old and new states to the function.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: stable@vger.kernel.org # 6.1
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206114856.2665066-2-imre.deak@intel.com
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_uevent_modalias() does not modify the device pointer passed to
it, so mark it constant. In order to properly do this, a number of
busses need to have a modalias function added as they were attempting to
just point to of_device_uevent_modalias instead of their bus-specific
modalias function. This is fine except if the prototype for a bus and
device type modalias function diverges and then problems could happen. To
prevent all of that, just wrap the call to of_device_uevent_modalias()
directly for each bus and device type individually.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Liang He <windhl@126.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Corentin Labbe <clabbe@baylibre.com>
Cc: Zou Wei <zou_wei@huawei.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@lists.linux.dev
Cc: dri-devel@lists.freedesktop.org
Cc: devicetree@vger.kernel.org
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[why & how]
We still need to refer to port while removing payload at commit_tail.
we should keep the kref till then to release.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2171
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Fixes: 4d07b0bc40 ("drm/display/dp_mst: Move all payload info into the atomic state")
Cc: stable@vger.kernel.org # 6.1
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Tested-by: Didier Raboud <odyx@debian.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If an MST stream is enabled on a disconnected sink, the payload for the
stream is not created and the MST manager's payload count/next start VC
slot is not updated. Since the payload's start VC slot may still contain
a valid value (!= -1) the subsequent disabling of such a stream could
cause an incorrect decrease of the payload count/next start VC slot in
drm_dp_remove_payload() and hence later payload additions will fail.
Fix the above by marking the payload as invalid in the above case, so
that it's skipped during payload removal. While at it add a debug print
for this case.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v6.1+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221214184258.2869417-3-imre.deak@intel.com
After an error during receiving a packet for a multi-packet DP MST
sideband message, the state tracking which packets have been received
already is not reset. This prevents the reception of subsequent down
messages (due to the pending message not yet completed with an
end-of-message-transfer packet).
Fix the above by resetting the reception state after a packet error.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221214184258.2869417-2-imre.deak@intel.com
If the sink gets disconnected during receiving a multi-packet DP MST AUX
down-reply/up-request sideband message, the state keeping track of which
packets have been received already is not reset. This results in a failed
sanity check for the subsequent message packet received after a sink is
reconnected (due to the pending message not yet completed with an
end-of-message-transfer packet), indicated by the
"sideband msg set header failed"
error.
Fix the above by resetting the up/down message reception state after a
disconnect event.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221214184258.2869417-1-imre.deak@intel.com
