- Add hooks in various entry points to perform hw/sw init for DCN6 asic
- Add dependent changes needed to enable DCN6 asic
- Update the Makefiles so that DCN6 related newly added sources are compiled
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN6 code to DC, DML2, and DMUB
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add all the bits to enable DSC over FRL.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds a few, relatively minor, changes for FRL to
clk_mgr, DSC, and HDCP blocks.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Fix various warnings related to unsigned/signed mismatches
- Consistently use the same signedness for a given value
- Explcitly cast between types when needed
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Clay King <clayking@amd.com>
Signed-off-by: James Lin <pinglei.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Address signed/unsigned comparison warnings across dc paths to keep
builds warning-clean and improve type safety at comparison boundaries.
Most warnings came from signed loop/index temporaries compared against
unsigned counters and table sizes, plus a smaller number of mixed
signed/unsigned clock, bandwidth, and geometry comparisons.
[How]
Aligned iterator and temporary variable types with the semantic type
of the compared bounds. Used unsigned indices for loops bounded by unsigned
counters and table sizes, while retaining signed types where values are
semantically signed or participate in arithmetic that may legitimately go
negative. Where mixed signed/unsigned comparisons are intentional, applied
explicit boundary casts or guarded comparisons instead of broad type
changes.
No functional behavior changes are intended; this is a warning-resolution
and type-alignment cleanup.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Gaghik Khachatrian <gaghik.khachatrian@amd.com>
Signed-off-by: James Lin <pinglei.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] drm/amd/display had implicit integer narrowing at protocol/storage boundaries
and an incomplete eDP assignment in integrated info parsing.
[How] Apply explicit boundary casts for intentional narrowing, keep intermediate math
in wider types, and restore explicit eDP field mapping in v2.2 parser.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Gaghik Khachatrian <gaghik.khachatrian@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Reworked YCbCr4:2:2 Native/Simple policy decision making with DSC
enabled based on DSC caps and stream signal type
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Reworked YCbCr4:2:2 Native/Simple policy decision making with DSC
enabled based on DSC caps and stream signal type
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Chuanyu Tseng <chuanyu.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FGCG shouldn't be called at the DC resource level as part of DSC
creation because dc_create is intended for SW init, not HW init, and
register access is not guaranteed to work at this phase.
[How]
Add a set_fgcg function at the DSC interface level.
Existing ASIC can continue using the function in DC resource to retain
current compatibility but further development should favor calling
the function pointer during init_hw (if it exists).
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the typo "miniumum" → "minimum" in a comment in dc_dsc.c.
This typo is already listed in scripts/spelling.txt by commit
8c32002657 ("scripts/spelling.txt: add several more common spelling
mistakes").
Suggested-by: Cryolitia PukNgae <cryolitia@uniontech.com>
Signed-off-by: Runrun Liu <liurunrun@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
dcn35 currently uses a hardcoded DSC display clock value which is incorrect
for some asic types. Newer DCN versions retrieve dsc display clock from
clk_mgr. The same can be done for dcn35.
how:
Refactor the DSC cap calculation using pre-existing logic.
Handle ODM combine requirements in dc_dsc.c.
Replace hardcoded display clock with actual value retrieved from clk_mgr.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Mohit Bawa <Mohit.Bawa@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Debugging underflow issues frequently requires knowing the
HW state at the time of underflow. To enable capturing this
HW state information, interface functions are needed for the
various DC HW blocks.
[How]
This change adds the interface functions to read HW state for
the following DC HW blocks:
- HUBBUB
- HUBP
- DPP
- MPC
- OPP
- DSC
- OPTC
- DCCG
Reviewed-by: George Shen <george.shen@amd.com>
Signed-off-by: Karen Chen <Karen.Chen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-OVT compliance testing for 5120x2880p300Hz YCbCr420 was failing due to
incorrect slice width being calculated
[How]
-Ensure slice width is divisible by 2 for 420 to comply with spec
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-Certain OVT timings require DSC configurations which divide the
horizontal active unevenly across DSC slices
-DSC slices must be even, so padding needs to be added to the active
to make this possible
-The pixel clock of the HW now needs to be increased to accommodate
the extra padded pixels
-To keep the line time the same, the blank of the HW timing needs to
be increased as well
[How]
-Calculate h_active padding, h_total padding, and pixel clock based
off of the original OVT timing and DSC calculations
-Store these values in the pipe and program HW with these modifications
-Added general support for cases where DSC slice config does not evenly
split the horizontal active by fixing some slice width calculations
-Updated PPS calculations for these cases
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
The sink max slice width limitation should be considered for DSC, but
was removed in "refactor DSC cap calculations".
This patch adds it back and takes the valid minimum between the sink and
source.
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
If the debug option is set to disable_dsc the max slice width and/or
dispclk can be zero. This causes a divide by zero when calculating the
min ODM combine factor. Add a check to ensure they are valid first.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[WHY]
DSC block level should only be responsible for reporting single DSC
instance capabilities. Factoring in ODM combine requirements should be
handled in dc_dsc.c. Both components should acquire clocks from clk_mgr
to determine throughput capabilities instead of relying on hard coded
values as these can differ by SoC and SKU.
[HOW]
1) Add dsc_get_single_enc_caps to acquire single DSC instance
capabilities (replacing dsc_get_enc_caps), factoring in DSCCLK
2) add build_dsc_enc_caps to combine single DSC instance capabilities
3) account for max pixel rate per pipe (DISPCLK) when calculating
minimum slice count
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Expose dcn401_initialize_min_clocks() for future use and add additional
check for IP register.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Karthi Kandasamy <karthi.kandasamy@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Expose some function for new platform use
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Karthi Kandasamy <karthi.kandasamy@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously the 'dsc_bits_per_comp' enumeration was defined in individual
.c files, making it unavailable for other files that may need it.
[How]
The 'dsc_bits_per_comp' enumeration has been relocated to a common header
file.
Reviewed-by: Mounika Adhuri <Mounika.Adhuri@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Signed-off-by: Bhuvanachandra Pinninti <bpinnint@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the static qualifier to make it available for code sharing
with other components.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Dmytro <dmytro.laktyushkin@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No common dsc params found between encoder and decoder is one
of the reason that could prevent dsc from properly enabled.
Dump the params to a specific timing to help locate possible
invalid dsc params in either encoder or decoder side.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since is_dsc_possible is already checked just above, there's no need to
check it again before filling out the DSC settings.
Signed-off-by: Bhavin Sharma <bhavin.sharma@siliconsignals.io>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY && HOW]
For some HDMI OVT timing, YCbCr422 encoding fails at the DSC
bandwidth check. The root cause is our DSC policy for timing
doesn't account for HDMI YCbCr422 native support.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Leo Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are some monitor timings that seem to be supported without
DSC but actually require DSC to be displayed. A VESA SCR introduced
a new max uncompressed pixel rate cap register that we can use to
handle these edge cases.
[HOW]
SST: Read caps from link and invalidate timings that exceed the
max limit but do not support DSC. Then check for options override
when determining BPP.
MST: Read caps from virtual DPCD peer device or daisy chained SST
monitor and set validation set BPPs to max if pixel rate exceeds
uncompressed limit. Validation set optimization continues as normal.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/dsc/dcn401/dcn401_dsc.c:30:24: warning:
symbol 'dcn401_dsc_funcs' was not declared. Should it be static?
This symbol is not used outside of dcn401_dsc.c, so marks it static.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC was waiting for the wrong field to disconnect cleanly.
[HOW]
Changed field the DSC disconnect was waiting on.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When system exits idle state followed by enabling the display,
DSC memory may still be forced in a deep sleep or shutdown state.
Intermittent DSC corruption is seen when display is visible.
[HOW]
When DSC is enabled, reset dsc memory to force and disable status.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit removes some unused code with the required adjustments.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Compilation errors while compiling without CONFIG_DRM_AMD_DC_FP:
"undefined reference to `dc_bandwidth_in_kbps_from_timing'"
[How]
Fix Makefile to move dsc files out of DC_FP guard.
Fixes: 00c391102a ("drm/amd/display: Add misc DC changes for DCN401")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move dsc functions from dc.c to dc_dsc.c.
Co-developed-by: George Shen <george.shen@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DML2.1 has added the support to determine ODM combine based on DSC slice
count limitation. This support would allow us to support DSC slice higher
than 4 on small timings. The change will allow higher DSC slice support
independent from pixel clock in use.
[HOW]
Add a DCN401 get_enc_caps function to allow the support for DSC slice count
higher than 4.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Switching between DSC clock or disable DSC block are not double buffered update.
Corruption is observed if these updates happen before DSC double buffered
disconnection.
[how]
Move DSC disable and refclk reset to post unlock update. Wait for DSC double buffered
disconnection and all mpccs are disconnected before reset DSC clock.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why && How]
Copyright notice failed in the Palamida scan and make changes to
align with our guidelines.
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Leo Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSC slice must be divisible by ODM slice count.
[how]
If DSC slice count is not a multiple of ODM slice count, increase DSC
slice until it is. Otherwise fail to compute DSC configuration.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When slice_height is 0, the division by slice_height in the calculation
of the number of slices will cause a division by zero driver crash. This
leaves the kernel in a state that requires a reboot. This patch adds a
check to avoid the division by zero.
The stack trace below is for the 6.8.4 Kernel. I reproduced the issue on
a Z16 Gen 2 Lenovo Thinkpad with a Apple Studio Display monitor
connected via Thunderbolt. The amdgpu driver crashed with this exception
when I rebooted the system with the monitor connected.
kernel: ? die (arch/x86/kernel/dumpstack.c:421 arch/x86/kernel/dumpstack.c:434 arch/x86/kernel/dumpstack.c:447)
kernel: ? do_trap (arch/x86/kernel/traps.c:113 arch/x86/kernel/traps.c:154)
kernel: ? setup_dsc_config (drivers/gpu/drm/amd/amdgpu/../display/dc/dsc/dc_dsc.c:1053) amdgpu
kernel: ? do_error_trap (./arch/x86/include/asm/traps.h:58 arch/x86/kernel/traps.c:175)
kernel: ? setup_dsc_config (drivers/gpu/drm/amd/amdgpu/../display/dc/dsc/dc_dsc.c:1053) amdgpu
kernel: ? exc_divide_error (arch/x86/kernel/traps.c:194 (discriminator 2))
kernel: ? setup_dsc_config (drivers/gpu/drm/amd/amdgpu/../display/dc/dsc/dc_dsc.c:1053) amdgpu
kernel: ? asm_exc_divide_error (./arch/x86/include/asm/idtentry.h:548)
kernel: ? setup_dsc_config (drivers/gpu/drm/amd/amdgpu/../display/dc/dsc/dc_dsc.c:1053) amdgpu
kernel: dc_dsc_compute_config (drivers/gpu/drm/amd/amdgpu/../display/dc/dsc/dc_dsc.c:1109) amdgpu
After applying this patch, the driver no longer crashes when the monitor
is connected and the system is rebooted. I believe this is the same
issue reported for 3113.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jose Fernandez <josef@netflix.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3113
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust bytes per pixel calculation to use div_u64.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Enabling higher compiler warning levels results in many issues that can
be trivially resolved as well as some potentially critical issues.
[how]
Fix all compiler warnings found with various compilers and higher
warning levels. Primarily, potentially uninitialized variables and
unreachable code.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why && How]
The current bandwidth calculation for timing doesn't account for
certain HDMI modes overhead which leads to DSC can't be enabled.
Add support to calculate the actual bandwidth for these HDMI modes.
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Update DSC DPCD parsing to take granular throughput adjustment into
consideration.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To refactor DSC and make DSC files unit testable.
[how]
moved the dcnxx_dsc.c and .h files
into corresponding dcn folders inside
the dsc and cleared the linkage errors.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Bhuvana Chandra Pinninti <bhuvanachandra.pinninti@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There certain cases where the timing BW is dependent on the type of link
encoding in use. Thus to calculate the correct BW required for a given
timing, the link encoding should be added as a parameter.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
