Commit 5df5dafc17 ("Bluetooth: hci_uart: Fix another race during
initialization") fixed a race for hci commands sent during initialization.
However, there is still a race that happens if an hci event from one of
these commands is received before HCI_UART_REGISTERED has been set at
the end of hci_uart_register_dev(). The event will be ignored which
causes the command to fail with a timeout in the log:
"Bluetooth: hci0: command 0x1003 tx timeout"
This is because the hci event receive path (hci_uart_tty_receive ->
h4_recv) requires HCI_UART_REGISTERED to be set in h4_recv(), while the
hci command transmit path (hci_uart_send_frame -> h4_enqueue) only
requires HCI_UART_PROTO_INIT to be set in hci_uart_send_frame().
The check for HCI_UART_REGISTERED was originally added in commit
c257820291 ("Bluetooth: Fix H4 crash from incoming UART packets")
to fix a crash caused by hu->hdev being null dereferenced. That can no
longer happen: once HCI_UART_PROTO_INIT is set in hci_uart_register_dev()
all pointers (hu, hu->priv and hu->hdev) are valid, and
hci_uart_tty_receive() already calls h4_recv() on HCI_UART_PROTO_INIT
or HCI_UART_PROTO_READY.
Remove the check for HCI_UART_REGISTERED in h4_recv() to fix the race
condition.
Fixes: 5df5dafc17 ("Bluetooth: hci_uart: Fix another race during initialization")
Signed-off-by: Jonathan Rissanen <jonathan.rissanen@axis.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btusb_work() maps the number of active SCO links to USB alternate
settings through a three-entry lookup table when CVSD traffic uses
transparent voice settings. The lookup currently indexes alts[] with
data->sco_num - 1 without first constraining sco_num to the number of
available table entries.
While the table only defines alternate settings for up to three SCO
links, data->sco_num comes from hci_conn_num() and is used directly.
Cap the lookup to the last table entry before indexing it so the
driver keeps selecting the highest supported alternate setting without
reading past alts[].
Fixes: baac6276c0 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btintel_hw_error() issues two __hci_cmd_sync() calls (HCI_OP_RESET
and Intel exception-info retrieval) without holding
hci_req_sync_lock(). This lets it race against
hci_dev_do_close() -> btintel_shutdown_combined(), which also runs
__hci_cmd_sync() under the same lock. When both paths manipulate
hdev->req_status/req_rsp concurrently, the close path may free the
response skb first, and the still-running hw_error path hits a
slab-use-after-free in kfree_skb().
Wrap the whole recovery sequence in hci_req_sync_lock/unlock so it
is serialized with every other synchronous HCI command issuer.
Below is the data race report and the kasan report:
BUG: data-race in __hci_cmd_sync_sk / btintel_shutdown_combined
read of hdev->req_rsp at net/bluetooth/hci_sync.c:199
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x114/0x670 drivers/bluetooth/btintel.c:254
hci_error_reset+0x348/0xa30 net/bluetooth/hci_core.c:1030
write/free by task ioctl/22580:
btintel_shutdown_combined+0xd0/0x360
drivers/bluetooth/btintel.c:3648
hci_dev_close_sync+0x9ae/0x2c10 net/bluetooth/hci_sync.c:5246
hci_dev_do_close+0x232/0x460 net/bluetooth/hci_core.c:526
BUG: KASAN: slab-use-after-free in
sk_skb_reason_drop+0x43/0x380 net/core/skbuff.c:1202
Read of size 4 at addr ffff888144a738dc
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x186/0x670 drivers/bluetooth/btintel.c:260
Fixes: 973bb97e5a ("Bluetooth: btintel: Add generic function for handling hardware errors")
Signed-off-by: Cen Zhang <zzzccc427@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Smatch reports:
drivers/bluetooth/hci_ll.c:587 download_firmware() warn:
'fw' from request_firmware() not released on lines: 544.
In download_firmware(), if request_firmware() succeeds but the returned
firmware content is invalid (no data or zero size), the function returns
without releasing the firmware, resulting in a resource leak.
Fix this by calling release_firmware() before returning when
request_firmware() succeeded but the firmware content is invalid.
Fixes: 371805522f ("bluetooth: hci_uart: add LL protocol serdev driver support")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Anas Iqbal <mohd.abd.6602@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The setup process previously combined error handling and retry gating
under one condition. As a result, the final failed attempt exited
without performing cleanup.
Update the failure path to always perform power and port cleanup on
setup failure, and reopen the port only when retrying.
Fixes: 9e80587aba ("Bluetooth: hci_qca: Enhance retry logic in qca_setup")
Signed-off-by: Jinwang Li <jinwang.li@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor tweaks
and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaZR1VQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfsACghiyMgr0XKVDFEpV7/fPzocKH+o0An3v8knSi
kLz/f6LstVsISqCxeT+9
=uozB
-----END PGP SIGNATURE-----
Merge tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor
tweaks and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits)
Revert "tty: tty_port: add workqueue to flip TTY buffer"
tty: tty_port: add workqueue to flip TTY buffer
serial: 8250_pci: Remove custom deprecated baud setting routine
serial: 8250_omap: Remove custom deprecated baud setting routine
dt-bindings: serial: renesas,scif: Document RZ/G3L SoC
serial: 8250: omap: set out-of-band wakeup if wakeup pinctrl exists
tty: hvc-iucv: Remove KMSG_COMPONENT macro
dt-bindings: serial: google,goldfish-tty: Convert to DT schema
dt-bindings: serial: sh-sci: Fold single-entry compatibles into enum
serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done
serial: 8250: 8250_omap.c: Add support for handling UART error conditions
serial: SH_SCI: improve "DMA support" prompt
serial: Kconfig: fix ordering of entries for menu display
serial: 8250: fix ordering of entries for menu display
serial: imx: change SERIAL_IMX_CONSOLE to bool
8250_men_mcb: drop unneeded MODULE_ALIAS
serial: men_z135_uart: drop unneeded MODULE_ALIAS
dt-bindings: serial: renesas,rsci: Document RZ/V2H(P) and RZ/V2N SoCs
serial: rsci: Convert to FIELD_MODIFY()
dt-bindings: serial: 8250: add SpacemiT K3 UART compatible
...
Core & protocols
----------------
- A significant effort all around the stack to guide the compiler to
make the right choice when inlining code, to avoid unneeded calls for
small helper and stack canary overhead in the fast-path. This
generates better and faster code with very small or no text size
increases, as in many cases the call generated more code than the
actual inlined helper.
- Extend AccECN implementation so that is now functionally complete,
also allow the user-space enabling it on a per network namespace
basis.
- Add support for memory providers with large (above 4K) rx buffer.
Paired with hw-gro, larger rx buffer sizes reduce the number of
buffers traversing the stack, dincreasing single stream CPU usage by
up to ~30%.
- Do not add HBH header to Big TCP GSO packets. This simplifies the RX
path, the TX path and the NIC drivers, and is possible because
user-space taps can now interpret correctly such packets without the
HBH hint.
- Allow IPv6 routes to be configured with a gateway address that is
resolved out of a different interface than the one specified, aligning
IPv6 to IPv4 behavior.
- Multi-queue aware sch_cake. This makes it possible to scale the rate
shaper of sch_cake across multiple CPUs, while still enforcing a
single global rate on the interface.
- Add support for the nbcon (new buffer console) infrastructure to
netconsole, enabling lock-free, priority-based console operations that
are safer in crash scenarios.
- Improve the TCP ipv6 output path to cache the flow information, saving
cpu cycles, reducing cache line misses and stack use.
- Improve netfilter packet tracker to resolve clashes for most protocols,
avoiding unneeded drops on rare occasions.
- Add IP6IP6 tunneling acceleration to the flowtable infrastructure.
- Reduce tcp socket size by one cache line.
- Notify neighbour changes atomically, avoiding inconsistencies between
the notification sequence and the actual states sequence.
- Add vsock namespace support, allowing complete isolation of vsocks
across different network namespaces.
- Improve xsk generic performances with cache-alignment-oriented
optimizations.
- Support netconsole automatic target recovery, allowing netconsole
to reestablish targets when underlying low-level interface comes back
online.
Driver API
----------
- Support for switching the working mode (automatic vs manual) of a DPLL
device via netlink.
- Introduce PHY ports representation to expose multiple front-facing
media ports over a single MAC.
- Introduce "rx-polarity" and "tx-polarity" device tree properties, to
generalize polarity inversion requirements for differential signaling.
- Add helper to create, prepare and enable managed clocks.
Device drivers
--------------
- Add Huawei hinic3 PF etherner driver.
- Add DWMAC glue driver for Motorcomm YT6801 PCIe ethernet controller.
- Add ethernet driver for MaxLinear MxL862xx switches
- Remove parallel-port Ethernet driver.
- Convert existing driver timestamp configuration reporting to
hwtstamp_get and remove legacy ioctl().
- Convert existing drivers to .get_rx_ring_count(), simplifing the RX
ring count retrieval. Also remove the legacy fallback path.
- Ethernet high-speed NICs:
- Broadcom (bnxt, bng):
- bnxt: add FW interface update to support FEC stats histogram and
NVRAM defragmentation
- bng: add TSO and H/W GRO support
- nVidia/Mellanox (mlx5):
- improve latency of channel restart operations, reducing the used
H/W resources
- add TSO support for UDP over GRE over VLAN
- add flow counters support for hardware steering (HWS) rules
- use a static memory area to store headers for H/W GRO, leading to
12% RX tput improvement
- Intel (100G, ice, idpf):
- ice: reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new layouts
- ice: introduces Synchronous Ethernet (SyncE) support
- Meta (fbnic):
- adds debugfs for firmware mailbox and tx/rx rings vectors
- Ethernet virtual:
- geneve: introduce GRO/GSO support for double UDP encapsulation
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- some code refactoring and cleanups
- RealTek (r8169):
- add support for RTL8127ATF (10G Fiber SFP)
- add dash and LTR support
- Airoha:
- AN8811HB 2.5 Gbps phy support
- Freescale (fec):
- add XDP zero-copy support
- Thunderbolt:
- add get link setting support to allow bonding
- Renesas:
- add support for RZ/G3L GBETH SoC
- Ethernet switches:
- Maxlinear:
- support R(G)MII slow rate configuration
- add support for Intel GSW150
- Motorcomm (yt921x):
- add DCB/QoS support
- TI:
- icssm-prueth: support bridging (STP/RSTP) via the switchdev
framework
- Ethernet PHYs:
- Realtek:
- enable SGMII and 2500Base-X in-band auto-negotiation
- simplify and reunify C22/C45 drivers
- Micrel: convert bindings to DT schema
- CAN:
- move skb headroom content into skb extensions, making CAN metadata
access more robust
- CAN drivers:
- rcar_canfd:
- add support for FD-only mode
- add support for the RZ/T2H SoC
- sja1000: cleanup the CAN state handling
- WiFi:
- implement EPPKE/802.1X over auth frames support
- split up drop reasons better, removing generic RX_DROP
- additional FTM capabilities: 6 GHz support, supported number of
spatial streams and supported number of LTF repetitions
- better mac80211 iterators to enumerate resources
- initial UHR (Wi-Fi 8) support for cfg80211/mac80211
- WiFi drivers:
- Qualcomm/Atheros:
- ath11k: support for Channel Frequency Response measurement
- ath12k: a significant driver refactor to support
multi-wiphy devices and and pave the way for future device support
in the same driver (rather than splitting to ath13k)
- ath12k: support for the QCC2072 chipset
- Intel:
- iwlwifi: partial Neighbor Awareness Networking (NAN) support
- iwlwifi: initial support for U-NII-9 and IEEE 802.11bn
- RealTek (rtw89):
- preparations for RTL8922DE support
- Bluetooth:
- implement setsockopt(BT_PHY) to set the connection packet type/PHY
- set link_policy on incoming ACL connections
- Bluetooth drivers:
- btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE
- btqca: add WCN6855 firmware priority selection feature
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=O31Y
-----END PGP SIGNATURE-----
Merge tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core & protocols:
- A significant effort all around the stack to guide the compiler to
make the right choice when inlining code, to avoid unneeded calls
for small helper and stack canary overhead in the fast-path.
This generates better and faster code with very small or no text
size increases, as in many cases the call generated more code than
the actual inlined helper.
- Extend AccECN implementation so that is now functionally complete,
also allow the user-space enabling it on a per network namespace
basis.
- Add support for memory providers with large (above 4K) rx buffer.
Paired with hw-gro, larger rx buffer sizes reduce the number of
buffers traversing the stack, dincreasing single stream CPU usage
by up to ~30%.
- Do not add HBH header to Big TCP GSO packets. This simplifies the
RX path, the TX path and the NIC drivers, and is possible because
user-space taps can now interpret correctly such packets without
the HBH hint.
- Allow IPv6 routes to be configured with a gateway address that is
resolved out of a different interface than the one specified,
aligning IPv6 to IPv4 behavior.
- Multi-queue aware sch_cake. This makes it possible to scale the
rate shaper of sch_cake across multiple CPUs, while still enforcing
a single global rate on the interface.
- Add support for the nbcon (new buffer console) infrastructure to
netconsole, enabling lock-free, priority-based console operations
that are safer in crash scenarios.
- Improve the TCP ipv6 output path to cache the flow information,
saving cpu cycles, reducing cache line misses and stack use.
- Improve netfilter packet tracker to resolve clashes for most
protocols, avoiding unneeded drops on rare occasions.
- Add IP6IP6 tunneling acceleration to the flowtable infrastructure.
- Reduce tcp socket size by one cache line.
- Notify neighbour changes atomically, avoiding inconsistencies
between the notification sequence and the actual states sequence.
- Add vsock namespace support, allowing complete isolation of vsocks
across different network namespaces.
- Improve xsk generic performances with cache-alignment-oriented
optimizations.
- Support netconsole automatic target recovery, allowing netconsole
to reestablish targets when underlying low-level interface comes
back online.
Driver API:
- Support for switching the working mode (automatic vs manual) of a
DPLL device via netlink.
- Introduce PHY ports representation to expose multiple front-facing
media ports over a single MAC.
- Introduce "rx-polarity" and "tx-polarity" device tree properties,
to generalize polarity inversion requirements for differential
signaling.
- Add helper to create, prepare and enable managed clocks.
Device drivers:
- Add Huawei hinic3 PF etherner driver.
- Add DWMAC glue driver for Motorcomm YT6801 PCIe ethernet
controller.
- Add ethernet driver for MaxLinear MxL862xx switches
- Remove parallel-port Ethernet driver.
- Convert existing driver timestamp configuration reporting to
hwtstamp_get and remove legacy ioctl().
- Convert existing drivers to .get_rx_ring_count(), simplifing the RX
ring count retrieval. Also remove the legacy fallback path.
- Ethernet high-speed NICs:
- Broadcom (bnxt, bng):
- bnxt: add FW interface update to support FEC stats histogram
and NVRAM defragmentation
- bng: add TSO and H/W GRO support
- nVidia/Mellanox (mlx5):
- improve latency of channel restart operations, reducing the
used H/W resources
- add TSO support for UDP over GRE over VLAN
- add flow counters support for hardware steering (HWS) rules
- use a static memory area to store headers for H/W GRO,
leading to 12% RX tput improvement
- Intel (100G, ice, idpf):
- ice: reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new
layouts
- ice: introduces Synchronous Ethernet (SyncE) support
- Meta (fbnic):
- adds debugfs for firmware mailbox and tx/rx rings vectors
- Ethernet virtual:
- geneve: introduce GRO/GSO support for double UDP encapsulation
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- some code refactoring and cleanups
- RealTek (r8169):
- add support for RTL8127ATF (10G Fiber SFP)
- add dash and LTR support
- Airoha:
- AN8811HB 2.5 Gbps phy support
- Freescale (fec):
- add XDP zero-copy support
- Thunderbolt:
- add get link setting support to allow bonding
- Renesas:
- add support for RZ/G3L GBETH SoC
- Ethernet switches:
- Maxlinear:
- support R(G)MII slow rate configuration
- add support for Intel GSW150
- Motorcomm (yt921x):
- add DCB/QoS support
- TI:
- icssm-prueth: support bridging (STP/RSTP) via the switchdev
framework
- Ethernet PHYs:
- Realtek:
- enable SGMII and 2500Base-X in-band auto-negotiation
- simplify and reunify C22/C45 drivers
- Micrel: convert bindings to DT schema
- CAN:
- move skb headroom content into skb extensions, making CAN
metadata access more robust
- CAN drivers:
- rcar_canfd:
- add support for FD-only mode
- add support for the RZ/T2H SoC
- sja1000: cleanup the CAN state handling
- WiFi:
- implement EPPKE/802.1X over auth frames support
- split up drop reasons better, removing generic RX_DROP
- additional FTM capabilities: 6 GHz support, supported number of
spatial streams and supported number of LTF repetitions
- better mac80211 iterators to enumerate resources
- initial UHR (Wi-Fi 8) support for cfg80211/mac80211
- WiFi drivers:
- Qualcomm/Atheros:
- ath11k: support for Channel Frequency Response measurement
- ath12k: a significant driver refactor to support multi-wiphy
devices and and pave the way for future device support in the
same driver (rather than splitting to ath13k)
- ath12k: support for the QCC2072 chipset
- Intel:
- iwlwifi: partial Neighbor Awareness Networking (NAN) support
- iwlwifi: initial support for U-NII-9 and IEEE 802.11bn
- RealTek (rtw89):
- preparations for RTL8922DE support
- Bluetooth:
- implement setsockopt(BT_PHY) to set the connection packet type/PHY
- set link_policy on incoming ACL connections
- Bluetooth drivers:
- btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE
- btqca: add WCN6855 firmware priority selection feature"
* tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1254 commits)
bnge/bng_re: Add a new HSI
net: macb: Fix tx/rx malfunction after phy link down and up
af_unix: Fix memleak of newsk in unix_stream_connect().
net: ti: icssg-prueth: Add optional dependency on HSR
net: dsa: add basic initial driver for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add tag format for MxL862xx switches
dt-bindings: net: dsa: add MaxLinear MxL862xx
selftests: drivers: net: hw: Modify toeplitz.c to poll for packets
octeontx2-pf: Unregister devlink on probe failure
net: renesas: rswitch: fix forwarding offload statemachine
ionic: Rate limit unknown xcvr type messages
tcp: inet6_csk_xmit() optimization
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_syn_recv_sock()
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_connect()
ipv6: inet6_csk_xmit() and inet6_csk_update_pmtu() use inet->cork.fl.u.ip6
ipv6: use inet->cork.fl.u.ip6 and np->final in ip6_datagram_dst_update()
ipv6: use np->final in inet6_sk_rebuild_header()
ipv6: add daddr/final storage in struct ipv6_pinfo
net: stmmac: qcom-ethqos: fix qcom_ethqos_serdes_powerup()
...
- Add the missing IRQF_COND_ONESHOT flag to devm_request_irq()
This is inconsistent vs. request_irq() and causes the same issues which
where addressed with the introduction of this flag
- Cleanup IRQF_ONESHOT and IRQF_NO_THREAD usage
Quite some drivers have inconsistent interrupt request flags related to
interrupt threading namely IRQF_ONESHOT and IRQF_NO_THREAD. This leads to
warnings and/or malfunction when forced interrupt threading is enabled.
- Remove stub primary (hard interrupt) handlers
A bunch of drivers implement a stub primary (hard interrupt) handler which
just returns IRQ_WAKE_THREAD. The same functionality is provided by the
core code when the primary handler argument of request_thread_irq() is set
to NULL.
-----BEGIN PGP SIGNATURE-----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=vrmm
-----END PGP SIGNATURE-----
Merge tag 'irq-cleanups-2026-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq cleanups from Thomas Gleixner:
"A series of treewide cleanups to ensure interrupt request consistency.
- Add the missing IRQF_COND_ONESHOT flag to devm_request_irq()
This is inconsistent vs request_irq() and causes the same issues
which where addressed with the introduction of this flag
- Cleanup IRQF_ONESHOT and IRQF_NO_THREAD usage
Quite some drivers have inconsistent interrupt request flags
related to interrupt threading namely IRQF_ONESHOT and
IRQF_NO_THREAD. This leads to warnings and/or malfunction when
forced interrupt threading is enabled.
- Remove stub primary (hard interrupt) handlers
A bunch of drivers implement a stub primary (hard interrupt)
handler which just returns IRQ_WAKE_THREAD. The same functionality
is provided by the core code when the primary handler argument of
request_thread_irq() is set to NULL"
* tag 'irq-cleanups-2026-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
media: pci: mg4b: Use IRQF_NO_THREAD
mfd: wm8350-core: Use IRQF_ONESHOT
thermal/qcom/lmh: Replace IRQF_ONESHOT with IRQF_NO_THREAD
rtc: amlogic-a4: Remove IRQF_ONESHOT
usb: typec: fusb302: Remove IRQF_ONESHOT
EDAC/altera: Remove IRQF_ONESHOT
char: tpm: cr50: Remove IRQF_ONESHOT
ARM: versatile: Remove IRQF_ONESHOT
scsi: efct: Use IRQF_ONESHOT and default primary handler
Bluetooth: btintel_pcie: Use IRQF_ONESHOT and default primary handler
bus: fsl-mc: Use default primary handler
mailbox: bcm-ferxrm-mailbox: Use default primary handler
iommu/amd: Use core's primary handler and set IRQF_ONESHOT
platform/x86: int0002: Remove IRQF_ONESHOT from request_irq()
genirq: Set IRQF_COND_ONESHOT in devm_request_irq().
There is no added value in btintel_pcie_msix_isr() compared to
irq_default_primary_handler().
Using a threaded interrupt without a dedicated primary handler mandates
the IRQF_ONESHOT flag to mask the interrupt source while the threaded
handler is active. Otherwise the interrupt can fire again before the
threaded handler had a chance to run.
Use the default primary interrupt handler by specifying NULL and set
IRQF_ONESHOT so the interrupt source is masked until the secondary
handler is done.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-7-bigeasy@linutronix.de
Add QCA_CAP_HFP_HW_OFFLOAD capability flag to WCN6855 and WCN7850
device data structures to enable Hands-Free Profile (HFP) hardware
offload support on these Qualcomm Bluetooth chipsets.
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace SoC-specific check with capability-based approach for HFP
hardware offload configuration. Add QCA_CAP_HFP_HW_OFFLOAD capability
flag and support_hfp_hw_offload field to qca_serdev structure. Add
QCA_CAP_HFP_HW_OFFLOAD capability flag to QCA2066 device data
structures.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling
hci_uart_register_dev(), which calls proto->open() to initialize
hu->priv. However, if a TTY write wakeup occurs during this window,
hci_uart_tx_wakeup() may schedule write_work before hu->priv is
initialized, leading to a NULL pointer dereference in
hci_uart_write_work() when proto->dequeue() accesses hu->priv.
The race condition is:
CPU0 CPU1
---- ----
hci_uart_set_proto()
set_bit(HCI_UART_PROTO_INIT)
hci_uart_register_dev()
tty write wakeup
hci_uart_tty_wakeup()
hci_uart_tx_wakeup()
schedule_work(&hu->write_work)
proto->open(hu)
// initializes hu->priv
hci_uart_write_work()
hci_uart_dequeue()
proto->dequeue(hu)
// accesses hu->priv (NULL!)
Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open()
succeeds, ensuring hu->priv is initialized before any work can be
scheduled.
Fixes: 5df5dafc17 ("Bluetooth: hci_uart: Fix another race during initialization")
Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/
Signed-off-by: Jia-Hong Su <s11242586@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The USB device ID 0x13d3/0x3618 is listed twice in the device table.
Remove the duplicate entry and keep the one under the correct
"Realtek 8852BT/8852BE-VT Bluetooth devices" section.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add USB device ID 0x2c0a:0x8761 to the btusb driver fo the Realtek
RTL8761BU Bluetooth adapter.
Reference:
https://www.startech.com/en-us/networking-io/av53c1-usb-bluetooth
Signed-off-by: Jacopo Scannella <code@charlie.cat>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The functions are already disabled if CONFIG_PM or CONFIG_PM_SLEEP are
disabled through the use of SET_SYSTEM_SLEEP_PM_OPS() and
SET_RUNTIME_PM_OPS().
This increases build coverage and allows to drop a few #ifdef's.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The functions are already disabled through the use of pm_ptr() when
CONFIG_PM is disabled, and will be removed from the final linked code
as not needed.
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The kfree_skb() function internally checks if the skb is NULL,
so an explicit check before calling it is redundant and can be removed.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If USB autosuspend occurs while discovery is active, the ongoing
HCI operation may not complete successfully. On some devices, this
can leave discovery.state stuck in DISCOVERY_FINDING.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add USB ID 0489:e112 for the Realtek 8851BE Bluetooth adapter.
Without this entry, the device is not handled correctly by btusb and Bluetooth fails to initialise.
Adding the ID enables proper Realtek initialization for Bluetooth to work on various motherboards using this Bluetooth adapter.
The device identifies as:
Bus 001 Device XXX: ID 0489:e112 Foxconn / Hon Hai Bluetooth Radio
Tested on Realtek 8851BE. Bluetooth works after this change is made.
Signed-off-by: Techie Ernie <techieernie@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Historically, WCN685x and QCA2066 shared the same firmware files.
Now, changes are planned for the firmware that will make it incompatible
with QCA2066, so a new firmware name is required for WCN685x.
Test Steps:
- Boot device
- Check the BTFW loading status via dmesg
Sanity pass and Test Log:
QCA Downloading qca/wcnhpbftfw21.tlv
Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
QCA Downloading qca/hpbftfw21.tlv
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
WCN7850 will first attempt to use ELF_TYPE_PATCH,
and if that fails, it will fall back to TLV_TYPE_PATCH.
To code uniformity, move WCN7850 workaround to the caller.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Switch to the generic PCI power management framework and remove legacy
callbacks like .suspend() and .resume(). With the generic framework, the
standard PCI related work like:
- pci_save/restore_state()
- pci_enable/disable_device()
- pci_set_power_state()
is handled by the PCI core and this driver should implement only
hci_bcm4377 specific operations in its respective callback functions.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On QCS9075 and QCA8275 platforms, the BT_EN pin is always pulled up by hw
and cannot be controlled by the host. As a result, in case of a firmware
crash, the host cannot trigger a cold reset. Instead, the BT controller
performs a warm restart on its own, without reloading the firmware.
This leads to the controller remaining in IBS_WAKE state, while the host
expects it to be in sleep mode. The mismatch causes HCI reset commands
to time out. Additionally, the driver does not clear internal flags
QCA_SSR_TRIGGERED and QCA_IBS_DISABLED, which blocks the reset sequence.
If the SSR duration exceeds 2 seconds, the host may enter TX sleep mode
due to tx_idle_timeout, further preventing recovery. Also, memcoredump_flag
is not cleared, so only the first SSR generates a coredump.
Tell the driver that the BT controller has undergone a proper restart sequence:
- Clear QCA_SSR_TRIGGERED and QCA_IBS_DISABLED flags after SSR.
- Add a 50ms delay to allow the controller to complete its warm reset.
- Reset tx_idle_timer to prevent the host from entering TX sleep mode.
- Clear memcoredump_flag to allow multiple coredump captures.
Apply these steps only when HCI_QUIRK_NON_PERSISTENT_SETUP is not set,
which indicates that BT_EN is defined in DTS and cannot be toggled.
Refer to the comment in include/net/bluetooth/hci.h for details on
HCI_QUIRK_NON_PERSISTENT_SETUP.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling
hci_uart_register_dev(), which calls proto->open() to initialize
hu->priv. However, if a TTY write wakeup occurs during this window,
hci_uart_tx_wakeup() may schedule write_work before hu->priv is
initialized, leading to a NULL pointer dereference in
hci_uart_write_work() when proto->dequeue() accesses hu->priv.
The race condition is:
CPU0 CPU1
---- ----
hci_uart_set_proto()
set_bit(HCI_UART_PROTO_INIT)
hci_uart_register_dev()
tty write wakeup
hci_uart_tty_wakeup()
hci_uart_tx_wakeup()
schedule_work(&hu->write_work)
proto->open(hu)
// initializes hu->priv
hci_uart_write_work()
hci_uart_dequeue()
proto->dequeue(hu)
// accesses hu->priv (NULL!)
Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open()
succeeds, ensuring hu->priv is initialized before any work can be
scheduled.
Fixes: 5df5dafc17 ("Bluetooth: hci_uart: Fix another race during initialization")
Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/
Signed-off-by: Jia-Hong Su <s11242586@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 98921dbd00 ("Bluetooth: Use devm_kzalloc in
btusb.c file").
In btusb_probe(), we use devm_kzalloc() to allocate the btusb data. This
ties the lifetime of all the btusb data to the binding of a driver to
one interface, INTF. In a driver that binds to other interfaces, ISOC
and DIAG, this is an accident waiting to happen.
The issue is revealed in btusb_disconnect(), where calling
usb_driver_release_interface(&btusb_driver, data->intf) will have devm
free the data that is also being used by the other interfaces of the
driver that may not be released yet.
To fix this, revert the use of devm and go back to freeing memory
explicitly.
Fixes: 98921dbd00 ("Bluetooth: Use devm_kzalloc in btusb.c file")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace the open-coded multiplication in kmalloc() with a call
to kmalloc_array() to prevent potential integer overflows.
This is a mechanical change, replacing BCM_FW_NAME_LEN with
the type-safe sizeof(*fw_name) as the element size
Signed-off-by: Ayaan Mirza Baig <ayaanmirzabaig85@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds the infrastructure that allow the user space program to
talk to intel pcie driver directly for fetching basic driver details.
The changes introduced are referred form
commit 04425292a6 ("Bluetooth: Introduce HCI Driver protocol")
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The new platform uses the QCA2066 chip along with a new board ID, which
requires a dedicated firmware file to ensure proper initialization.
Without this entry, the driver cannot locate and load the correct
firmware, resulting in Bluetooth bring-up failure.
This patch adds a new entry to the firmware table for QCA2066 so that
the driver can correctly identify the board ID and load the appropriate
firmware from 'qca/QCA2066/' in the linux-firmware repository.
Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some Qualcomm Bluetooth controllers, e.g., QCNFA765 with WCN6855
chip, send debug packets as ACL frames with header 0x2EDC.
The kernel misinterprets these as malformed ACL packets, causing
repeated errors:
Bluetooth: hci0: ACL packet for unknown connection handle 3804
This can occur hundreds of times per minute, greatly cluttering logs.
On my computer, I am observing approximately 7 messages per second
when streaming audio to a speaker.
For Qualcomm controllers exchanging over UART, hci_qca.c already
filters out these debug packets. This patch is for controllers
not going through UART, but USB.
This patch uses the classify_pkt_type callback to reclassify the
packets with handle 0x2EDC as HCI_DIAG_PKT before they reach the
HCI layer. This change is only applied to Qualcomm devices marked
as BTUSB_QCA_WCN6855.
Tested on: Thinkpad T14 gen2 (AMD) with QCNFA765 (0489:E0D0)
Signed-off-by: Pascal Giard <pascal.giard@etsmtl.ca>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to a hardware bug during suspend/resume, the controller may miss a
doorbell interrupt. To address this, a retry mechanism has been added to
inform the controller before reporting a failure.
Test case:
- run suspend and resume cycles.
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During S4 (hibernate), the Bluetooth device loses power. Upon resume,
the driver performs the following actions:
1. Unregisters hdev
2. Calls function level reset
3. Registers hdev
Test case:
- run command sudo rtcwake -m disk -s 60
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The UART-based H5 protocol supports CRC data integrity checks for
reliable packets. The host sets bit 5 in the configuration field of the
CONFIG link control message to indicate that CRC is supported. The
controller sets the same bit in the CONFIG RESPONSE message to indicate
that CRC may be used from then on.
Tested on a MangoPi MQ-Pro with a Realtek RTL8723DS Bluetooth controller
using the tip of the bluetooth-next tree.
Signed-off-by: Javier Nieto <jgnieto@cs.stanford.edu>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Previously, h5_open() called h5_link_control() to send a SYNC message.
But h5_link_control() only enqueues the packet and requires the caller
to call hci_uart_tx_wakeup(). Thus, after H5_SYNC_TIMEOUT ran out
(100ms), h5_timed_event() would be called and, realizing that the state
was still H5_UNINITIALIZED, it would re-enqueue the SYNC and call
hci_uart_tx_wakeup(). Consequently, two SYNC packets would be sent and
initialization would unnecessarily wait for 100ms.
The naive solution of calling hci_uart_tx_wakeup() in h5_open() does not
work because it will only schedule tx work if the HCI_PROTO_READY bit is
set and hci_serdev only sets it after h5_open() returns. This patch
removes the extraneous SYNC being enqueued and makes h5_timed_event()
wake up on the next jiffy.
Signed-off-by: Javier Nieto <jgnieto@cs.stanford.edu>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Support the platform Bluetooth to be reset by hardware pin,
when a Bluetooth exception occurs, attempt to reset the
Bluetooth module using the hardware reset pin, as this
method is generally more stable and reliable than a
software reset. If the hardware reset pin is not specified
in the device tree, fall back to the existing software
reset mechanism to ensure backward compatibility.
Co-developed: Sean Wang <Sean.Wang@mediatek.com>
Co-developed: Hao Qin <hao.qin@mediatek.com>
Co-developed: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Zhangchao Zhang <ot_zhangchao.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In btusb_mtk_setup(), we set `btmtk_data->isopkt_intf` to:
usb_ifnum_to_if(data->udev, MTK_ISO_IFNUM)
That function can return NULL in some cases. Even when it returns
NULL, though, we still go on to call btusb_mtk_claim_iso_intf().
As of commit e9087e8288 ("Bluetooth: btusb: mediatek: Add locks for
usb_driver_claim_interface()"), calling btusb_mtk_claim_iso_intf()
when `btmtk_data->isopkt_intf` is NULL will cause a crash because
we'll end up passing a bad pointer to device_lock(). Prior to that
commit we'd pass the NULL pointer directly to
usb_driver_claim_interface() which would detect it and return an
error, which was handled.
Resolve the crash in btusb_mtk_claim_iso_intf() by adding a NULL check
at the start of the function. This makes the code handle a NULL
`btmtk_data->isopkt_intf` the same way it did before the problematic
commit (just with a slight change to the error message printed).
Reported-by: IncogCyberpunk <incogcyberpunk@proton.me>
Closes: http://lore.kernel.org/r/a380d061-479e-4713-bddd-1d6571ca7e86@leemhuis.info
Fixes: e9087e8288 ("Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface()")
Cc: stable@vger.kernel.org
Tested-by: IncogCyberpunk <incogcyberpunk@proton.me>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For chips with security enabled, it's only possible to load firmware
with a valid signature pattern.
If key_id is not zero, it indicates a security chip, and the driver will
not load the config file.
- Example log for a security chip.
Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: cfg_sz 0, total sz 71301
Bluetooth: hci0: RTL: fw version 0x41c0c905
- Example log for a normal chip.
Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 0
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_config.bin
Bluetooth: hci0: RTL: cfg_sz 6, total sz 71307
Bluetooth: hci0: RTL: fw version 0x41c0c905
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Nial Ni <niall_ni@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There is a KASAN: slab-use-after-free read in btusb_disconnect().
Calling "usb_driver_release_interface(&btusb_driver, data->intf)" will
free the btusb data associated with the interface. The same data is
then used later in the function, hence the UAF.
Fix by moving the accesses to btusb data to before the data is free'd.
Reported-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2fc81b50a4f8263a159b
Tested-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com
Fixes: fd913ef7ce ("Bluetooth: btusb: Add out-of-band wakeup support")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The memory allocated for ptr using kvmalloc() is not freed on the last
error path. Fix that by freeing it on that error path.
Fixes: 9a24ce5e29 ("Bluetooth: btrtl: Firmware format v2 support")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A different structure is stored in drvdata for the drivers which used
that duplicate function, but h4_recv_buf() assumes drvdata is always an
hci_uart structure.
Consequently, alignment and padding are now randomly corrupted for
btmtkuart, btnxpuart, and bpa10x in h4_recv_buf(), causing erratic
breakage.
Fix this by making the hci_uart structure the explicit argument to
h4_recv_buf(). Every caller already has a reference to hci_uart, and
already obtains the hci_hdev reference through it, so this actually
eliminates a redundant pointer indirection for all existing callers.
Fixes: 93f06f8f0d ("Bluetooth: remove duplicate h4_recv_buf() in header")
Reported-by: Francesco Valla <francesco@valla.it>
Closes: https://lore.kernel.org/lkml/6837167.ZASKD2KPVS@fedora.fritz.box/
Signed-off-by: Calvin Owens <calvin@wbinvd.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In the current btintel_pcie driver implementation, when an interrupt is
received, the driver checks for the alive cause before the TX/RX cause.
Handling the alive cause involves resetting the TX/RX queue indices.
This flow works correctly when the causes are mutually exclusive.
However, if both cause bits are set simultaneously, the alive cause
resets the queue indices, resulting in an event packet drop and a
command timeout. To fix this issue, the driver is modified to handle all
other causes before checking for the alive cause.
Test case:
Issue is seen with stress reboot scenario - 50x run
[20.337589] Bluetooth: hci0: Device revision is 0
[20.346750] Bluetooth: hci0: Secure boot is enabled
[20.346752] Bluetooth: hci0: OTP lock is disabled
[20.346752] Bluetooth: hci0: API lock is enabled
[20.346752] Bluetooth: hci0: Debug lock is disabled
[20.346753] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[20.346754] Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631
[20.359070] Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi
[20.371499] Bluetooth: hci0: Boot Address: 0xb02ff800
[20.385769] Bluetooth: hci0: Firmware Version: 166-34.25
[20.538257] Bluetooth: hci0: Waiting for firmware download to complete
[20.554424] Bluetooth: hci0: Firmware loaded in 178651 usecs
[21.081588] Bluetooth: hci0: Timeout (500 ms) on tx completion
[21.096541] Bluetooth: hci0: Failed to send frame (-62)
[21.110240] Bluetooth: hci0: sending frame failed (-62)
[21.138551] Bluetooth: hci0: Failed to send Intel Reset command
[21.170153] Bluetooth: hci0: Intel Soft Reset failed (-62)
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds logic to handle power management control when the
Bluetooth function is closed during the SDIO reset sequence.
Specifically, if BT is closed before reset, the driver enables the
SDIO function and sets driver pmctrl. After reset, if BT remains
closed, the driver sets firmware pmctrl and disables the SDIO function.
These changes ensure proper power management and device state consistency
across the reset flow.
Fixes: 8fafe70225 ("Bluetooth: mt7921s: support bluetooth reset mechanism")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently, bcsp_recv() can be called even when the BCSP protocol has not
been registered. This leads to a NULL pointer dereference, as shown in
the following stack trace:
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:bcsp_recv+0x13d/0x1740 drivers/bluetooth/hci_bcsp.c:590
Call Trace:
<TASK>
hci_uart_tty_receive+0x194/0x220 drivers/bluetooth/hci_ldisc.c:627
tiocsti+0x23c/0x2c0 drivers/tty/tty_io.c:2290
tty_ioctl+0x626/0xde0 drivers/tty/tty_io.c:2706
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
To prevent this, ensure that the HCI_UART_REGISTERED flag is set before
processing received data. If the protocol is not registered, return
-EUNATCH.
Reported-by: syzbot+4ed6852d4da4606c93da@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=4ed6852d4da4606c93da
Tested-by: syzbot+4ed6852d4da4606c93da@syzkaller.appspotmail.com
Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The "h4_recv.h" header contains a duplicate h4_recv_buf() that is nearly
but not quite identical to the h4_recv_buf() in hci_h4.c.
This duplicated header was added in commit 07eb96a5a7 ("Bluetooth:
bpa10x: Use separate h4_recv_buf helper"). I wasn't able to find any
explanation for duplicating the code in the discussion:
https://lore.kernel.org/all/20180320181855.37297-1-marcel@holtmann.org/https://lore.kernel.org/all/20180324091954.73229-2-marcel@holtmann.org/
Unfortunately, in the years since, several other drivers have come to
also rely on this duplicated function, probably by accident. This is, at
the very least, *extremely* confusing. It's also caused real issues when
it's become out-of-sync, see the following:
ef564119ba ("Bluetooth: hci_h4: Add support for ISO packets")
61b27cdf02 ("Bluetooth: hci_h4: Add support for ISO packets in h4_recv.h")
This is the full diff between the two implementations today:
--- orig.c
+++ copy.c
@@ -1,117 +1,100 @@
{
- struct hci_uart *hu = hci_get_drvdata(hdev);
- u8 alignment = hu->alignment ? hu->alignment : 1;
-
/* Check for error from previous call */
if (IS_ERR(skb))
skb = NULL;
while (count) {
int i, len;
- /* remove padding bytes from buffer */
- for (; hu->padding && count > 0; hu->padding--) {
- count--;
- buffer++;
- }
- if (!count)
- break;
-
if (!skb) {
for (i = 0; i < pkts_count; i++) {
if (buffer[0] != (&pkts[i])->type)
continue;
skb = bt_skb_alloc((&pkts[i])->maxlen,
GFP_ATOMIC);
if (!skb)
return ERR_PTR(-ENOMEM);
hci_skb_pkt_type(skb) = (&pkts[i])->type;
hci_skb_expect(skb) = (&pkts[i])->hlen;
break;
}
/* Check for invalid packet type */
if (!skb)
return ERR_PTR(-EILSEQ);
count -= 1;
buffer += 1;
}
len = min_t(uint, hci_skb_expect(skb) - skb->len, count);
skb_put_data(skb, buffer, len);
count -= len;
buffer += len;
/* Check for partial packet */
if (skb->len < hci_skb_expect(skb))
continue;
for (i = 0; i < pkts_count; i++) {
if (hci_skb_pkt_type(skb) == (&pkts[i])->type)
break;
}
if (i >= pkts_count) {
kfree_skb(skb);
return ERR_PTR(-EILSEQ);
}
if (skb->len == (&pkts[i])->hlen) {
u16 dlen;
switch ((&pkts[i])->lsize) {
case 0:
/* No variable data length */
dlen = 0;
break;
case 1:
/* Single octet variable length */
dlen = skb->data[(&pkts[i])->loff];
hci_skb_expect(skb) += dlen;
if (skb_tailroom(skb) < dlen) {
kfree_skb(skb);
return ERR_PTR(-EMSGSIZE);
}
break;
case 2:
/* Double octet variable length */
dlen = get_unaligned_le16(skb->data +
(&pkts[i])->loff);
hci_skb_expect(skb) += dlen;
if (skb_tailroom(skb) < dlen) {
kfree_skb(skb);
return ERR_PTR(-EMSGSIZE);
}
break;
default:
/* Unsupported variable length */
kfree_skb(skb);
return ERR_PTR(-EILSEQ);
}
if (!dlen) {
- hu->padding = (skb->len + 1) % alignment;
- hu->padding = (alignment - hu->padding) % alignment;
-
/* No more data, complete frame */
(&pkts[i])->recv(hdev, skb);
skb = NULL;
}
} else {
- hu->padding = (skb->len + 1) % alignment;
- hu->padding = (alignment - hu->padding) % alignment;
-
/* Complete frame */
(&pkts[i])->recv(hdev, skb);
skb = NULL;
}
}
return skb;
}
-EXPORT_SYMBOL_GPL(h4_recv_buf)
As I read this: If alignment is one, and padding is zero, padding
remains zero throughout the loop. So it seems to me that the two
functions behave strictly identically in that case. All the duplicated
defines are also identical, as is the duplicated h4_recv_pkt structure
declaration.
All four drivers which use the duplicated function use the default
alignment of one, and the default padding of zero. I therefore conclude
the duplicate function may be safely replaced with the core one.
I raised this in an RFC a few months ago, and didn't get much interest:
https://lore.kernel.org/all/CABBYNZ+ONkYtq2fR-8PtL3X-vetvJ0BdP4MTw9cNpjLDzG3HUQ@mail.gmail.com/
...but I'm still wary I've missed something, and I'd really appreciate
more eyeballs on it.
I tested this successfully on btnxpuart a few months ago, but
unfortunately I no longer have access to that hardware.
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Calvin Owens <calvin@wbinvd.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
As device coredumps are not HCI traces, maintain the device coredump at
the driver level and eliminate the dependency on hdev_devcd*()
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: 07e6bddb54 ("Bluetooth: btintel_pcie: Add support for device coredump")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
kzalloc() already zero-initializes the destination buffer 'data', making
strscpy() sufficient for safely copying 'name'. The additional
NUL-padding performed by strscpy_pad() is unnecessary.
Add a new local variable to store the length of 'name' and reuse it
instead of recalculating the same length.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Implement hdev->wakeup() callback to support Wake On BT feature.
Test steps:
1. echo enabled > /sys/bus/pci/devices/0000:00:14.7/power/wakeup
2. connect bluetooth hid device
3. put the system to suspend - rtcwake -m mem -s 300
4. press any key on hid to wake up the system
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This prevents the comments going over 80 columns which is still
required for Bluetooth code.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add Bluetooth CNVi core and platform names to the PCI device table for
each device ID as a comment.
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implements _suspend() and _resume() functions for the
Bluetooth controller. When the system enters a suspended state, the
driver notifies the controller to perform necessary housekeeping tasks
by writing to the sleep control register and waits for an alive
interrupt. The firmware raises the alive interrupt when it has
transitioned to the D3 state. The same flow occurs when the system
resumes.
Command to test host initiated wakeup after 60 seconds
sudo rtcwake -m mem -s 60
dmesg log (tested on Whale Peak2 on Panther Lake platform)
On system suspend:
[Fri Jul 25 11:05:37 2025] Bluetooth: hci0: device entered into d3 state from d0 in 80 us
On system resume:
[Fri Jul 25 11:06:36 2025] Bluetooth: hci0: device entered into d0 state from d3 in 7117 us
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the BlazarIW Bluetooth core used in the Wildcat Lake
platform.
HCI traces:
< HCI Command: Intel Read Version (0x3f|0x0005) plen 1
Requested Type:
All Supported Types(0xff)
> HCI Event: Command Complete (0x0e) plen 122
Intel Read Version (0x3f|0x0005) ncmd 1
Status: Success (0x00)
.....
CNVi BT(18): 0x00223700 - BlazarIW(0x22)
.....
.....
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some Kconfig dependencies are needed after my recent cleanup, since
the core code has its own option.
Since btmtksdio does not actually call h4_recv_buf(), move the
definitions it uses outside the BT_HCIUART_H4 gate in hci_uart.h to
avoid adding a dependency for btmtksdio.
The rest I touched (bpa10x, btmtkuart, and btnxpuart) do really call
h4_recv_buf(), so the dependency is required, add it for them.
Fixes: 0e272fc7e17d ("Bluetooth: remove duplicate h4_recv_buf() in header")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202508300413.OnIedvRh-lkp@intel.com/
Signed-off-by: Calvin Owens <calvin@wbinvd.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move the creation of debugfs files into a dedicated function, and ensure
they are explicitly removed during vhci_release(), before associated
data structures are freed.
Previously, debugfs files such as "force_suspend", "force_wakeup", and
others were created under hdev->debugfs but not removed in
vhci_release(). Since vhci_release() frees the backing vhci_data
structure, any access to these files after release would result in
use-after-free errors.
Although hdev->debugfs is later freed in hci_release_dev(), user can
access files after vhci_data is freed but before hdev->debugfs is
released.
Fixes: ab4e4380d4 ("Bluetooth: Add vhci devcoredump support")
Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This replaces devm_request_irq() with devm_request_threaded_irq().
On iMX93 11x11 EVK platform, the BT chip's BT_WAKE_OUT pin is connected
to an I2C GPIO expander instead of directly been connected to iMX GPIO.
When I2C GPIO expander's (PCAL6524) host driver receives an interrupt on
it's INTR line, the driver's interrupt handler needs to query the
interrupt source with PCAL6524 first, and then call the actual interrupt
handler, in this case the IRQ handler in BTNXPUART.
In order to handle interrupts when such I2C GPIO expanders are between
the host and interrupt source, devm_request_threaded_irq() is needed.
This commit also removes the IRQF_TRIGGER_FALLING flag, to allow setting
the IRQ trigger type from the device tree setting instead of hardcoding
in the driver.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During the shutdown process, an interrupt occurs that
prematurely terminates the wait for the expected event.
This change replaces TASK_INTERRUPTIBLE with
TASK_UNINTERRUPTIBLE in the wait_on_bit_timeout call to ensure
the shutdown process completes as intended without being
interrupted by signals.
Fixes: d019930b00 ("Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.c")
Signed-off-by: Jiande Lu <jiande.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The firmware raises an alive interrupt upon sending the HCI_RESET or
BTINTEL_HCI_OP_RESET command. As part of handling the reset command,
firmware initializes the hardware and data path and raises the alive
interrupt. Upon receiving the alive interrupt, the driver must enable
the data path and grant RX buffers to the firmware before sending any
commands.
The alive context maintained in the driver must be updated before
sending BTINTEL_HCI_OP_RESET or HCI_OP_RESET to prevent a potential race
condition where the context is also updated in the threaded IRQ.
The issue was observed in a stress reboot usecase (1/25) using "sudo
reboot" command where the firmware download was failing as the driver
was not granting RX buffer to firmware due to race condition.
Bluetooth: hci0: API lock is disabled
Bluetooth: hci0: Debug lock is disabled
Bluetooth: hci0: Minimum firmware build 1 week 10 2014
Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631
Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi
Bluetooth: hci0: Boot Address: 0xb0301000
Bluetooth: hci0: Firmware Version: 167-12.25
Bluetooth: hci0: Waiting for firmware download to complete
Bluetooth: hci0: Firmware loaded in 99902 usecs
Bluetooth: hci0: Alive context: fw_dl old_boot_stage: 0xa0db0003
new_boot_stage: 0xa0db0003
Bluetooth: hci0: sent cmd: 0xfc01 alive context changed:
fw_dl -> intel_reset1
Bluetooth: hci0: Waiting for device to boot
Bluetooth: hci0: Device boot timeout
Bluetooth: hci0: Firmware download retry count: 1
Fixes: 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The firmware raises an alive interrupt upon receiving the HCI_RESET or
BTINTEL_HCI_OP_RESET (Intel reset - 0xfc01) command. This change fixes
the driver to properly wait for the alive interrupt to avoid driver
sending commands to firmware before it is ready to process.
For details on the handshake between the driver and firmware, refer to
commit 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between
driver and firmware").
As the driver needs to handle two interrupts for HCI_OP_RESET and
BTINTEL_HCI_OP_RESET, the firmware ensures that the TX completion
interrupt is always followed by the alive interrupt.
Fixes: 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware")
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Sort WCN6855 device IDs to more easily manage them.
Signed-off-by: Zijun Hu <Zijun.Hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There are custom-made firmwares based on board ID for a given QCA BT
chip sometimes, and they are different with existing firmwares and put
in a separate subdirectory to avoid conflict, for example:
QCA2066, as a variant of WCN6855, has firmwares under 'qca/QCA2066/'
of linux-firmware repository.
Support downloading custom-made firmwares based on a table newly added.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds uevents which will be generated whenever FW dump is triggered,
FW dump is complete and FW (re)download is done.
This feature is needed for IW612 chipset, which is a tri-radio chipset,
where WLAN runs on CPU1 and BT and Zigbee runs on CPU2.
Currently, whenever BT FW crashes, and FW dump is in progress, there is
no way for 15.4 application to know that CPU2 is in bad state, and when
it will be recovered.
With the help of these uevents and udev rules, the 15.4 app, or any
userspace application can be alerted whenever CPU2 goes in bad state and
recoveres after BTNXPUART reloads the firmware.
[ 334.255154] Bluetooth: hci0: ==== Start FW dump ===
[ 334.261003] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_DUMP_ACTIVE ===
[ 351.486048] Bluetooth: hci0: ==== FW dump complete ===
[ 351.491356] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_DUMP_DONE ===
[ 352.028974] Bluetooth: hci0: ChipID: 7601, Version: 0
[ 352.034490] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se
[ 353.979977] Bluetooth: hci0: FW Download Complete: 417064 bytes
[ 355.197222] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_READY ===
Tested this change by creating a simple udev rule to store the
BTNXPUART_STATE value in a ~/<BTNXPUART_DEV>/state file, and running
15.4 traffic.
The 15.4 packets were sent over SPI only when BTNXPUART_STATE was
FW_READY.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Tested-by: Jean-Yves Salaün <jean-yves.salaun@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds proper handling for the independent reset command sent by the
driver after FW dump is complete.
In normal scenario, the independent reset vendor command gives a success
response before jumping to bootcode.
However, when FW goes in a bad state, and sends out FW dump packets, the
independent reset command does not get any response from the controller.
[ 159.807732] Bluetooth: hci0: ==== Start FW dump ===
[ 180.759060] Bluetooth: hci0: ==== FW dump complete ===
[ 182.779208] Bluetooth: hci0: command 0xfcfc tx timeout
[ 183.364974] Bluetooth: hci0: ChipID: 7601, Version: 0
[ 183.368490] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se
[ 184.679977] Bluetooth: hci0: FW Download Complete: 417064 bytes
[ 187.963102] Bluetooth: hci0: Opcode 0x0c03 failed: -110
As a fix for such scenario, the independent reset vendor command is sent
using the __hci_cmd_send() API, which does not expect any response for
vendor commands.
__hci_cmd_send is non blocking, so before the tx_work is scheduled, it
sometimes gets canceled and 3F|FC command is never sent. Adding a small
delay after __hci_cmd_send allows the command to be sent to the
controller.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Tested-by: Jean-Yves Salaün <jean-yves.salaun@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use macro for Intel Reset command (0xfc01) instead of hard coded value.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Avoid potential NULL pointer dereference by checking the return value of
kmalloc and handling allocation failure properly.
Fixes: 7d70989fce ("Bluetooth: btusb: Add HCI Drv commands for configuring altsetting")
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
NXP bluetooth chip shares power supply and reset gpio with a WLAN
chip. Add support for power supply and reset and enforce powerup
sequence:
- apply power supply
- deassert reset/powerdown
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for 4000000 as secondary baudrate.
This value is selected from device tree property "max-speed"
which is then used to download FW chunks, and as operational baudrate after
HCI initialization is done.
Earlier, the secondary baudrate was fixed to 3000000 in driver, but now
with "max-speed" property, this secondary baudrate can be set to
4000000.
The secondary baudrate is set by the driver by sending a vendor command
(3F 09) to the firmware, with secondary baudrate parameter, in
nxp_post_init().
Any other value set for max-speed other than 3000000 or 4000000 will
default to 3000000, which is supported by all legacy and new NXP chipsets.
This feature is applicable for all new V3 bootloader chips and w8987 V1
bootloader chip.
This property does not apply for w8997 compatible device, since it
downloads a helper.bin FW file that sets secondary baudrate as 3000000
only.
The switch to 4000000 baudrate is validated using a Saleae Logic Analyzer
and imx8m-mini with AW693 M.2 module.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Enable ISO data packet RX for LE audio.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This rewords the term restart with recovery since the intend is for
hardware recovery not a regular restart, also remove some debug logs
which might just clutter the output informing the recovery counter which
isn't really useful for regular users.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver supports Function Level Reset (FLR) to recover the controller
upon hardware exceptions or hci command timeouts. FLR is triggered only
when no prior reset has occurred within the retry window, with a maximum
of one FLR allowed within this window.
This patch is tested by,
echo 1 > /sys/class/bluetooth/hciX/reset
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For GF variant of WCN6855 without board ID programmed
btusb_generate_qca_nvm_name() will chose wrong NVM
'qca/nvm_usb_00130201.bin' to download.
Fix by choosing right NVM 'qca/nvm_usb_00130201_gf.bin'.
Also simplify NVM choice logic of btusb_generate_qca_nvm_name().
Fixes: d6cba4e6d0 ("Bluetooth: btusb: Add support using different nvm for variant WCN6855 controller")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The 'quirks' member already ran out of bits on some platforms some time
ago. Replace the integer member by a bitmap in order to have enough bits
in future. Replace raw bit operations by accessor macros.
Fixes: ff26b2dd65 ("Bluetooth: Add quirk for broken READ_VOICE_SETTING")
Fixes: 127881334e ("Bluetooth: Add quirk for broken READ_PAGE_SCAN_TYPE")
Suggested-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to what seem to be a bug with variant version returned by some
firmwares the code may set hdev->classify_pkt_type with
btintel_classify_pkt_type when in fact the controller doesn't even
support ISO channels feature but may use the handle range expected from
a controllers that does causing the packets to be reclassified as ISO
causing several bugs.
To fix the above btintel_classify_pkt_type will attempt to check if the
controller really supports ISO channels and in case it doesn't don't
reclassify even if the handle range is considered to be ISO, this is
considered safer than trying to fix the specific controller/firmware
version as that could change over time and causing similar problems in
the future.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219553
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2100565
Link: https://github.com/StarLabsLtd/firmware/issues/180
Fixes: f25b7fd36c ("Bluetooth: Add vendor-specific packet classification for ISO data")
Cc: stable@vger.kernel.org
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Sean Rhodes <sean@starlabs.systems>
Some modules have BT_EN enabled via a hardware pull-up,
meaning it is not defined in the DTS and is not controlled
through the power sequence. In such cases, fall through
to follow the legacy flow.
Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During firmware download, if an error occurs, interrupts must be
disabled, synchronized, and re-enabled before retrying the download.
This change ensures proper interrupt handling to prevent race
conditions.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent invalid
routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused transient
packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmhK/3IACgkQMUZtbf5S
IruE5A//RdwiBW/pqoMIiRKLA3HZeUA/beYOl4DwVf8WFQNUIqdboeAi6k4yFrS+
SykKN0s1z8fW45lA46iFv3sR0QKYGln/v/cANsqojYqKBD3PF42dRifFlEAIz2M5
fnXK1VHPJOFK/OBOyKiiW3R6mFv+v9epZM8BKED77vFy7osDV2zkObePeE8/34B7
yVAr6JNTpB5Ex4ziG+e/6tFF6IX9RJLBl4fkRRynLDSsb1NFuy39LxPsxRQPxnzo
tlfHfxEFl5qDNGondUoSxmp38HoO6MRofWp1d1GZoBbTXi0gXV26I5WaaBHBqPkm
jZ7AtIMQq2+JuEg0y4dFFRehZLwLEMuhvlbacbIOKNBngVIsploBzvbG3ntWuUa4
Z5VFayQXumsHB5g7+vEFK6vCPaIpatKt419JsFXogNvVmmQzghALFlSymm/WbyGL
Bj3R448xGDJw+2zDAXSH/nMMHkRaQd2Ptj2czvJ0Y7Fj8bxJgH0okaHOBrk9RQTQ
bdUGCiMY84p6WI7rKDkFyyohMxppdYsY8A9hSdGgpqvu7dZi5yGmzz1Sp9+uSfSF
Lj61am4LSvRsIuTP5cdqmTBn3mZS5R49hvJsFddgXRhF+Y9gB7LSm0sypZbuOEKD
m9ijKcNETglzer0iMCwAVrIbDHGjqqHS74DkRzsuPsQ8kaCjsno=
=0mtm
-----END PGP SIGNATURE-----
Merge tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
Modify the driver to post 3 fewer buffers than the maximum rx buffers
(64) allowed for the firmware. This change mitigates a hardware issue
causing a race condition in the firmware, improving stability and data
handling.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This change addresses latency issues observed in HID use cases where
events arrive in bursts. By increasing the Rx descriptor count to 64,
the firmware can handle bursty data more effectively, reducing latency
and preventing buffer overflows.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver was posting only 6 rx buffers, despite the maximum rx buffers
being defined as 16. Having fewer RX buffers caused firmware exceptions
in HID use cases when events arrived in bursts.
Exception seen on android 6.12 kernel.
E Bluetooth: hci0: Received hw exception interrupt
E Bluetooth: hci0: Received gp1 mailbox interrupt
D Bluetooth: hci0: 00000000: ff 3e 87 80 03 01 01 01 03 01 0c 0d 02 1c 10 0e
D Bluetooth: hci0: 00000010: 01 00 05 14 66 b0 28 b0 c0 b0 28 b0 ac af 28 b0
D Bluetooth: hci0: 00000020: 14 f1 28 b0 00 00 00 00 fa 04 00 00 00 00 40 10
D Bluetooth: hci0: 00000030: 08 00 00 00 7a 7a 7a 7a 47 00 fb a0 10 00 00 00
D Bluetooth: hci0: 00000000: 10 01 0a
E Bluetooth: hci0: ---- Dump of debug registers —
E Bluetooth: hci0: boot stage: 0xe0fb0047
E Bluetooth: hci0: ipc status: 0x00000004
E Bluetooth: hci0: ipc control: 0x00000000
E Bluetooth: hci0: ipc sleep control: 0x00000000
E Bluetooth: hci0: mbox_1: 0x00badbad
E Bluetooth: hci0: mbox_2: 0x0000101c
E Bluetooth: hci0: mbox_3: 0x00000008
E Bluetooth: hci0: mbox_4: 0x7a7a7a7a
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL
returned by gpiod_get_optional()") accidentally changed the prevous
behavior where power control would be disabled without the BT_EN GPIO
only on QCA_WCN6750 and QCA_WCN6855 while also getting the error check
wrong. We should treat every IS_ERR() return value from
devm_gpiod_get_optional() as a reason to bail-out while we should only
set power_ctrl_enabled to false on the two models mentioned above. While
at it: use dev_err_probe() to save a LOC.
Cc: stable@vger.kernel.org
Fixes: 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hsin-chen Chuang <chharry@chromium.org>
Reviewed-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Return value of devm_request_irq() must be checked (function is even
annotated) and without it clang W=1 complains:
btnxpuart.c:494:6: error: unused variable 'ret' [-Werror,-Wunused-variable]
Setting up wakeup IRQ handler is not really critical, because the
handler is empty, so just log the informational message so user could
submit proper bug report and silences the clang warning.
Fixes: c50b56664e ("Bluetooth: btnxpuart: Implement host-wakeup feature")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since the size of struct btintel_dsbr is already known, we can just
start there instead of querying the EFI variable size. If the final
result doesn't match what we expect also fail. This fixes a stack buffer
overflow when the EFI variable is larger than struct btintel_dsbr.
Reported-by: zepta <z3ptaa@gmail.com>
Closes: https://lore.kernel.org/all/CAPBS6KoaWV9=dtjTESZiU6KK__OZX0KpDk-=JEH8jCHFLUYv3Q@mail.gmail.com
Fixes: eb9e749c01 ("Bluetooth: btintel: Allow configuring drive strength of BRI")
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use skb_pull() and skb_pull_data() to safely parse QCA dump packets.
This avoids direct pointer math on skb->data, which could lead to
invalid access if the packet is shorter than expected.
Fixes: 20981ce2d5 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit b16b327edb.
The sysfs node introduced by this patch could potentially race with user
space. The original motivation - Support configuring altsetting from the
user space will be added by another series.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 75ddcd5ad4.
This patch doesn't work quite well - It's observed that with this patch
HFP is flaky on most of the existing USB Bluetooth controllers: Intel
chips sometimes send out no packet for Transparent codec; MTK chips may
generate SCO data with a wrong handle for CVSD codec; RTK could split
the data with a wrong packet size for Transparent codec; ... etc.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Although commit 75ddcd5ad4 ("Bluetooth: btusb: Configure altsetting
for HCI_USER_CHANNEL") has enabled the HCI_USER_CHANNEL user to send out
SCO data through USB Bluetooth chips, it's observed that with the patch
HFP is flaky on most of the existing USB Bluetooth controllers: Intel
chips sometimes send out no packet for Transparent codec; MTK chips may
generate SCO data with a wrong handle for CVSD codec; RTK could split
the data with a wrong packet size for Transparent codec; ... etc.
To address the issue above one needs to reset the altsetting back to
zero when there is no active SCO connection, which is the same as the
BlueZ behavior, and another benefit is the bus doesn't need to reserve
bandwidth when no SCO connection.
This patch adds "Supported Altsettings" and "Switch Altsetting" commands
that allow the user space program to configure the altsetting freely.
This patch is tested on ChromeOS devices. The USB Bluetooth models
(CVSD, TRANS alt3, and TRANS alt6) could pass the stress HFP test narrow
band speech and wide band speech.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Fixes: b16b327edb ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Although commit 75ddcd5ad4 ("Bluetooth: btusb: Configure altsetting
for HCI_USER_CHANNEL") has enabled the HCI_USER_CHANNEL user to send out
SCO data through USB Bluetooth chips, it's observed that with the patch
HFP is flaky on most of the existing USB Bluetooth controllers: Intel
chips sometimes send out no packet for Transparent codec; MTK chips may
generate SCO data with a wrong handle for CVSD codec; RTK could split
the data with a wrong packet size for Transparent codec; ... etc.
To address the issue above one needs to reset the altsetting back to
zero when there is no active SCO connection, which is the same as the
BlueZ behavior, and another benefit is the bus doesn't need to reserve
bandwidth when no SCO connection.
This patch adds the infrastructure that allow the user space program to
talk to Bluetooth drivers directly:
- Define the new packet type HCI_DRV_PKT which is specifically used for
communication between the user space program and the Bluetooth drviers
- hci_send_frame intercepts the packets and invokes drivers' HCI Drv
callbacks (so far only defined for btusb)
- 2 kinds of events to user space: Command Status and Command Complete,
the former simply returns the status while the later may contain
additional response data.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Fixes: b16b327edb ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This implements host wakeup feature by reading the device tree property
wakeup-source and 'wakeup' interrupt, and nxp,wakeout-pin, and configuring
it as a FALLING EDGE triggered interrupt.
When host is suspended, a trigger from the WAKE_OUT pin of the
controller wakes it up.
To enable this feature, both device tree properties are needed to be
defined.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
release_firmware() checks for NULL pointers internally.
Remove unneeded NULL check for fmw here.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device can be unbound or probe can fail, so driver must also release
memory for the wakeup source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device can be unbound or probe can fail, so driver must also release
memory for the wakeup source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
All Intel diagnostic events are part of HCI traces and there is no need
to generate coredump for the same.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to a hardware issue, there is a possibility that the driver may miss
an MSIx interrupt on the RX/TX data path. Since the TX and RX paths are
independent, when a TX MSIx interrupt occurs, the driver can check the
RX queue for any pending data and process it if present. The same
approach applies to the RX path.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
To prevent Bluetooth SDIO card from be physically removed suddenly,
driver needs to ensure btmtksdio_close is called before
btmtksdio_remove to disable interrupts and txrx workqueue.
Fixes: 6ac4233afb ("Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Check BTMTKSDIO_FUNC_ENABLED flag before doing close to prevent
btmtksdio_close been called twice.
Fixes: 6ac4233afb ("Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A NULL pointer dereference can occur in skb_dequeue() when processing a
QCA firmware crash dump on WCN7851 (0489:e0f3).
[ 93.672166] Bluetooth: hci0: ACL memdump size(589824)
[ 93.672475] BUG: kernel NULL pointer dereference, address: 0000000000000008
[ 93.672517] Workqueue: hci0 hci_devcd_rx [bluetooth]
[ 93.672598] RIP: 0010:skb_dequeue+0x50/0x80
The issue stems from handle_dump_pkt_qca() returning 0 even when a dump
packet is successfully processed. This is because it incorrectly
forwards the return value of hci_devcd_init() (which returns 0 on
success). As a result, the caller (btusb_recv_acl_qca() or
btusb_recv_evt_qca()) assumes the packet was not handled and passes it
to hci_recv_frame(), leading to premature kfree() of the skb.
Later, hci_devcd_rx() attempts to dequeue the same skb from the dump
queue, resulting in a NULL pointer dereference.
Fix this by:
1. Making handle_dump_pkt_qca() return 0 on success and negative errno
on failure, consistent with kernel conventions.
2. Splitting dump packet detection into separate functions for ACL
and event packets for better structure and readability.
This ensures dump packets are properly identified and consumed, avoiding
double handling and preventing NULL pointer access.
Fixes: 20981ce2d5 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reuse the skb buffer provided by the PCIe driver to pass it onto the
stack, instead of copying it to a new skb.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Avoid double-copying of string literals. Use a "const char *" for each
string instead of copying from .rodata into stack and then into the skb.
We can go directly from .rodata to the skb.
This also works around a Clang bug (that has since been fixed[1]).
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401250927.1poZERd6-lkp@intel.com/
Fixes: ab4e4380d4 ("Bluetooth: Add vhci devcoredump support")
Link: ea2e66aa8b [1]
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This prints an error message if the FW Dump trigger command fails. This
scenario is mainly observed in legacy chipsets 8987 and 8997 and also
IW416, where this feature is unavailable due to memory constraints.
Fixes: 998e447f44 ("Bluetooth: btnxpuart: Add support for HCI coredump feature")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts the change baudrate logic in nxp_shutdown.
Earlier, when the driver was removed, it restored the controller
baudrate to fw_init_baudrate, so that on re-loading the driver, things
work fine.
However, if the driver was removed while hci0 interface is down, the
change baudrate vendor command could not be sent by the driver. When the
driver was re-loaded, host and controller baudrate would be mismatched
and hci initialization would fail. The only way to recover would be to
reboot the system.
This issue was fixed by moving the restore baudrate logic from
nxp_serdev_remove() to nxp_shutdown().
This fix however caused another issue with the command "hciconfig hci0
reset", which makes hci0 DOWN and UP immediately.
Running "bluetoothctl power off" and "bluetoothctl power on" in a tight
loop works fine.
To maintain support for "hciconfig reset" command, the above mentioned fix
is reverted.
Fixes: 6fca6781d1 ("Bluetooth: btnxpuart: Move vendor specific initialization to .post_init")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The QCA_WCN3950_SOC_ID_S should be using qca/cmnv13s.bin, rather than
qca/cmnv13u.bin file. Correct the variant suffix to be used for this SoC
ID.
Fixes: d5712c511c ("Bluetooth: qca: add WCN3950 support")
Reported-by: Wojciech Slenska <wsl@trackunit.com>
Closes: https://github.com/qualcomm-linux/meta-qcom/pull/817#discussion_r2022866431
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The btrtl_initialize() function checks that rtl_load_file() either
had an error or it loaded a zero length file. However, if it loaded
a zero length file then the error code is not set correctly. It
results in an error pointer vs NULL bug, followed by a NULL pointer
dereference. This was detected by Smatch:
drivers/bluetooth/btrtl.c:592 btrtl_initialize() warn: passing zero to 'ERR_PTR'
Fixes: 26503ad25d ("Bluetooth: btrtl: split the device initialization into smaller parts")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This handles the scenario where the driver receives an error code after
sending cmd5 or cmd7 in the bootloader signature during FW download.
The bootloader error code is handled by the driver and FW offset is
corrected accordingly, and the cmd5 or cmd7 is re-sent to the controller
in case of CRC error.
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This corrects the bootloader error codes for NXP chipsets.
Since we have a common handling for all error codes, there is no backward
compatibility issue.
Added error handling for CRC error code in V3 bootloader signature.
Fixes: 2748936429 ("Bluetooth: btnxpuart: Add handling for boot-signature timeout errors")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove the unwanted leading whitespace.
Fixes: 6ed8304738 ("Bluetooth: btintel_pcie: Setup buffers for firmware traces")
Fixes: bb3569ac36 ("Bluetooth: btintel: Add DSBR support for ScP")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BRDS - Bluetooth Regulatory Domain Specific absorption rate
Bluetooth has regulatory limitations which prohibit or allow usage of certain
bands or channels as well as limiting Tx power. The Tx power values can be
configured in ACPI table. This patch reads from ACPI entry configures the
controller accordingly.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Ensure interrupts are not re-enabled when the IRQ handler has already been
removed. This prevents unexpected IRQ handler execution due to stale or
unhandled interrupts.
Modify btmtksdio_txrx_work to check if bdev->func->irq_handler exists
before calling sdio_writel to enable interrupts.
Co-developed-by: Pedro Tsai <pedro.tsai@mediatek.com>
Signed-off-by: Pedro Tsai <pedro.tsai@mediatek.com>
Co-developed-by: Felix Freimann <felix.freimann@mediatek.com>
Signed-off-by: Felix Freimann <felix.freimann@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove the resetting step before downloading the fw, as it may cause
other usb devices to fail to initialise when connected during boot
on kernels 6.11 and newer.
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This sets HCI_QUIRK_SYNC_FLOWCTL_SUPPORTED which indicates that
controllers created by vhci driver support Sync Flow Control.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following warning:
drivers/bluetooth/btintel_pcie.c:695:20: warning: unused function 'btintel_pcie_in_rom' [-Wunused-function]
695 | static inline bool btintel_pcie_in_rom(struct btintel_pcie_data *data)
| ^~~~~~~~~~~~~~~~~~~
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Driver dumps device core dump on firmware exception.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for setting BD address during hci registration. NXP
FW does not allow vendor commands unless it receives a reset command
after FW download and initialization done.
As a workaround, the .set_bdaddr callback function will first send the
HCI reset command, followed by the actual vendor command to set BD
address.
The driver checks for the local-bd-address property in device tree, and
if preset, it sets the HCI_QUIRK_USE_BDADDR_PROPERTY quirk.
With this quirk set, the driver's set_bdaddr callback function is called
after FW download is complete and before HCI initialization, which sends
the hci reset and 3f 22 commands. During initialization, kernel reads
the newly set BD address from the controller.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Korsnes <johan.korsnes@remarkable.no>
Signed-off-by: Kristian Krohn <kristian.krohn@remarkable.no>
Tested-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for Bluetooth Coredump feature to BTNXPUART driver to
collect FW dumps on demand, or in case FW goes in a bad state.
To trigger manual FW dump, following command can be used:
echo 1 > /sys/class/bluetooth/hci0/device/coredump
Once FW dump is complete, it can be written to a file:
cat /sys/class/bluetooth/hci0/devcoredump/data > fw_dump
While FW dump is in progress, any HCI command will return -EBUSY.
After FW dump is complete, driver will give HCI_NXP_IND_RESET command
which soft-resets the chip, allowing FW re-download.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This moves change baudrate and power save vendor commands from
nxp_setup() to nxp_post_init().
This also moves the baudrate restore logic from nxp_serdev_remove() to
nxp_shutdown() which ensure baudrate is restored even when HCI dev is
down, preventing baudrate mismatch between host and controller when
device is probed again next time.
In case of removal when the hdev is up and running, we have to call the
shutdown procedure explicitly before unregistering the hdev.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Co-developed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Set HCI_READ_VOICE_SETTING and HCI_READ_PAGE_SCAN_TYPE as broken.
Once the min/max length of the commands began to be asserted, these fake
controllers can no longer be initialized because they return a smaller
report for these commands.
This affects various fake controllers reusing the 0A12:0001 VID/PID.
Fixes: c8992cffbe ("Bluetooth: hci_event: Use of a function table to handle Command Complete")
Signed-off-by: Pedro Nishiyama <nishiyama.pedro@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On hardware error, controller writes hardware error event and optional
vendor specific hci events in device memory in TLV format and raises
MSIX interrupt. Driver reads the device memory and passes the events to
the stack for further processing.
Co-developed-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch allocates the host memory which is used by controller to dump
the firmware traces. The memory needs to be shared with controller via
context information.
Co-developed-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
WCN3950 is another example of the WCN39xx BT/WiFI family of chips. It
requires different firmware files and has different current
requirements, so add it as a separate SoC type.
The firmware for these chips has been recently added to the
linux-firmware repository and will be a part of the upcoming release:
- qca/cmbtfw12.tlv
- qca/cmbtfw13.tlv
- qca/cmnv12.bin
- qca/cmnv13.bin
- qca/cmnv13s.bin
- qca/cmnv13t.bin
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The WCN399x code has two separate cases for loading the NVM data. In
preparation to adding support for WCN3950, which also requires similar
quirk, split the "variant" to be specified explicitly and merge two
snprintfs into a single one.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When using the out-of-band WAKE_IN and WAKE_OUT pins, we have to tell
the firmware which pins to use (from controller point of view). This
allows to report remote wakeup support when WAKE_OUT(c2h) is configured.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Older boards are having entry "enable-gpios" in dts, we can safely assume
latest boards which are supporting PMU node enrty will support power
sequencer.
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit b35108a51c ("jiffies: Define secs_to_jiffies()") introduced
secs_to_jiffies(). As the value here is a multiple of 1000, use
secs_to_jiffies() instead of msecs_to_jiffies to avoid the multiplication.
This is converted using scripts/coccinelle/misc/secs_to_jiffies.cocci with
the following Coccinelle rules:
@depends on patch@
expression E;
@@
-msecs_to_jiffies(E * 1000)
+secs_to_jiffies(E)
-msecs_to_jiffies(E * MSEC_PER_SEC)
+secs_to_jiffies(E)
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Do not set 'HCI_UART_PROTO_READY' before call 'hci_uart_register_dev()'.
Possible race is when someone calls 'hci_tty_uart_close()' after this bit
is set, but 'hci_uart_register_dev()' wasn't done. This leads to access
to uninitialized fields. To fix it let's set this bit after device was
registered (as before patch c411c62cc133) and to fix previous problem let's
add one more bit in addition to 'HCI_UART_PROTO_READY' which allows to
perform power up without original bit set (pls see commit c411c62cc133).
Crash backtrace from syzbot report:
RIP: 0010:skb_queue_empty_lockless include/linux/skbuff.h:1887 [inline]
RIP: 0010:skb_queue_purge_reason+0x6d/0x140 net/core/skbuff.c:3936
Call Trace:
<TASK>
skb_queue_purge include/linux/skbuff.h:3364 [inline]
mrvl_close+0x2f/0x90 drivers/bluetooth/hci_mrvl.c:100
hci_uart_tty_close+0xb6/0x120 drivers/bluetooth/hci_ldisc.c:557
tty_ldisc_close drivers/tty/tty_ldisc.c:455 [inline]
tty_ldisc_kill+0x66/0xc0 drivers/tty/tty_ldisc.c:613
tty_ldisc_release+0xc9/0x120 drivers/tty/tty_ldisc.c:781
tty_release_struct+0x10/0x80 drivers/tty/tty_io.c:1690
tty_release+0x4ef/0x640 drivers/tty/tty_io.c:1861
__fput+0x86/0x2a0 fs/file_table.c:450
task_work_run+0x82/0xb0 kernel/task_work.c:239
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
exit_to_user_mode_loop kernel/entry/common.c:114 [inline]
exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline]
__syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline]
syscall_exit_to_user_mode+0xa3/0x1b0 kernel/entry/common.c:218
do_syscall_64+0x9a/0x190 arch/x86/entry/common.c:89
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reported-by: syzbot+683f8cb11b94b1824c77@syzkaller.appspotmail.com
Tested-by: syzbot+683f8cb11b94b1824c77@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/d159c57f-8490-4c26-79da-6ad3612c4a14@salutedevices.com/
Fixes: 366ceff495 ("Bluetooth: hci_uart: fix race during initialization")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
'hci_register_dev()' calls power up function, which is executed by
kworker - 'hci_power_on()'. This function does access to bluetooth chip
using callbacks from 'hci_ldisc.c', for example 'hci_uart_send_frame()'.
Now 'hci_uart_send_frame()' checks 'HCI_UART_PROTO_READY' bit set, and
if not - it fails. Problem is that 'HCI_UART_PROTO_READY' is set after
'hci_register_dev()', and there is tiny chance that 'hci_power_on()' will
be executed before setting this bit. In that case HCI init logic fails.
Patch moves setting of 'HCI_UART_PROTO_READY' before calling function
'hci_uart_register_dev()'.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add DSBR support for Scorpious Peak cores.
Refer commit eb9e749c01 ("Bluetooth: btintel: Allow configuring drive
strength of BRI") for details about DSBR.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Output of checkpatch shows warning:
drivers/bluetooth/bfusb.c:368: WARNING: braces {} are not necessary
for single statement blocks
Remove braces for single line statement.
Signed-off-by: Jeremy Clifton <deaner92@yahoo.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add 13 USB device IDs for Qualcomm WCN785x, and these IDs are
extracted from Windows driver inf file for various types of
WoS (Windows on Snapdragon) laptop.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the error code to the message "Failed to claim iso
interface". That allows us to know which error case
usb_driver_claim_interface() hit.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Automatically configure the altsetting for HCI_USER_CHANNEL when a SCO
is connected.
The motivation is to enable the HCI_USER_CHANNEL user to send out SCO
data through USB Bluetooth chips, which is mainly used for bidirectional
audio transfer (voice call). This was not capable because:
- Per Bluetooth Core Spec v5, Vol 4, Part B, 2.1, the corresponding
alternate setting should be set based on the air mode in order to
transfer SCO data, but
- The Linux Bluetooth HCI_USER_CHANNEL exposes the Bluetooth Host
Controller Interface to the user space, which is something above the
USB layer. The user space is not able to configure the USB alt while
keeping the channel open.
This patch intercepts the HCI_EV_SYNC_CONN_COMPLETE packets in btusb,
extracts the air mode, and configures the alt setting in btusb.
This patch is tested on ChromeOS devices. The USB Bluetooth models
(CVSD, TRANS alt3 and alt6) could work without a customized kernel.
Fixes: b16b327edb ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Initialize .owner field of force_poll_sync_fops to THIS_MODULE in order to
prevent btusb from being unloaded while its operations are in use.
Fixes: 800fe5ec30 ("Bluetooth: btusb: Add support for queuing during polling interval")
Signed-off-by: Salah Triki <salah.triki@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The SCO packets from Bluetooth raw socket are now rejected because
hci_conn_num is left 0. This patch allows such the usecase to enable
the userspace SCO support.
Fixes: b16b327edb ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On HCI_OP_RESET command, firmware raises alive interrupt. Driver needs
to wait for this before sending other command. This patch fixes the potential
miss of alive interrupt due to which HCI_OP_RESET can timeout.
Expected flow:
If tx command is HCI_OP_RESET,
1. set data->gp0_received = false
2. send HCI_OP_RESET
3. wait for alive interrupt
Actual flow having potential race:
If tx command is HCI_OP_RESET,
1. send HCI_OP_RESET
1a. Firmware raises alive interrupt here and in ISR
data->gp0_received is set to true
2. set data->gp0_received = false
3. wait for alive interrupt
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware")
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Closes: https://patchwork.kernel.org/project/bluetooth/patch/20241001104451.626964-1-kiran.k@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes a regression caused by previous commit for fixing truncated
ACL data, which is causing some intermittent glitches when running two
A2DP streams.
serdev_device_write_buf() is the root cause of the glitch, which is
reverted, and the TX work will continue to write until the queue is empty.
This change fixes both issues. No A2DP streaming glitches or truncated
ACL data issue observed.
Fixes: 8023dd2204 ("Bluetooth: btnxpuart: Fix driver sending truncated data")
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The function enters infinite recursion if the HCI device doesn't support
GPIO reset: btusb_reset -> hdev->reset -> vendor_reset -> btusb_reset...
btusb_reset shouldn't call hdev->reset after commit f07d478090
("Bluetooth: Get rid of cmd_timeout and use the reset callback")
Fixes: f07d478090 ("Bluetooth: Get rid of cmd_timeout and use the reset callback")
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The documentation for usb_driver_claim_interface() says that "the
device lock" is needed when the function is called from places other
than probe(). This appears to be the lock for the USB interface
device. The Mediatek btusb code gets called via this path:
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
usb_driver_claim_interface
btusb_mtk_claim_iso_intf
btusb_mtk_setup
hci_dev_open_sync
hci_power_on
process_scheduled_works
worker_thread
kthread
With the above call trace the device lock hasn't been claimed. Claim
it.
Without this fix, we'd sometimes see the error "Failed to claim iso
interface". Sometimes we'd even see worse errors, like a NULL pointer
dereference (where `intf->dev.driver` was NULL) with a trace like:
Call trace:
usb_suspend_both
usb_runtime_suspend
__rpm_callback
rpm_suspend
pm_runtime_work
process_scheduled_works
Both errors appear to be fixed with the proper locking.
Fixes: ceac1cb025 ("Bluetooth: btusb: mediatek: add ISO data transmission functions")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For WCN6855, board ID specific NVM needs to be downloaded once board ID
is available, but the default NVM is always downloaded currently.
The wrong NVM causes poor RF performance, and effects user experience
for several types of laptop with WCN6855 on the market.
Fix by downloading board ID specific NVM if board ID is available.
Fixes: 095327fede ("Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855")
Cc: stable@vger.kernel.org # 6.4
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Steev Klimaszewski <steev@kali.org> #Thinkpad X13s
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The hdev->reset is never used now and the hdev->cmd_timeout actually
does reset. This patch changes the call path from
hdev->cmd_timeout -> vendor_cmd_timeout -> btusb_reset -> hdev->reset
, to
hdev->reset -> vendor_reset -> btusb_reset
Which makes it clear when we export the hdev->reset to a wider usage
e.g. allowing reset from sysfs.
This patch doesn't introduce any behavior change.
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove the cmd timeout count in btusb since we only ever allow one
command in flight at a time. We should always reset after a single
command times out.
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove resetting mt7921 before downloading the fw, as it may cause
command timeout when performing the reset.
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If insert an USB dongle which chip is not maintained in ic_id_table, it
will hit the NULL point accessed. Add a null point check to avoid the
Kernel Oops.
Fixes: b39910bb54 ("Bluetooth: Populate hci_set_hw_info for Intel and Realtek")
Reviewed-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
devm_kstrdup() can return a NULL pointer on failure,but this
returned value in btbcm_get_board_name() is not checked.
Add NULL check in btbcm_get_board_name(), to handle kernel NULL
pointer dereference error.
Fixes: f9183eaad9 ("Bluetooth: btbcm: Use devm_kstrdup()")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The firmware-name property has been expanded to specify the names of NVM
and rampatch firmware for certain chips, such as the QCA6698 Bluetooth
chip. Although it shares the same IP core as the WCN6855, the QCA6698
has different RF components and RAM sizes, necessitating new firmware
files. This change allows for the configuration of NVM and rampatch in
DT.
Possible configurations:
firmware-name = QCA6698/hpnv21.bin, QCA6698/hpbtfw21.tlv;
firmware-name = QCA6698/hpnv21, QCA6698/hpbtfw21.tlv;
Signed-off-by: Cheng Jiang <quic_chejiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Different connectivity boards may be attached to the same platform. For
example, QCA6698-based boards can support either a two-antenna or
three-antenna solution, both of which work on the sa8775p-ride platform.
Due to differences in connectivity boards and variations in RF
performance from different foundries, different NVM configurations are
used based on the board ID.
Therefore, in the firmware-name property, if the NVM file has an
extension, the NVM file will be used. Otherwise, the system will first
try the .bNN (board ID) file, and if that fails, it will fall back to
the .bin file.
Possible configurations:
firmware-name = "QCA6698/hpnv21";
firmware-name = "QCA6698/hpnv21.bin";
Signed-off-by: Cheng Jiang <quic_chejiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When a Bluetooth raw socket is open, the HCI event related to SCO
connection changes are not dispatched to the hci_event module, and
the underlying Bluetooth controller's USB Interface 1 will not be
updated accordingly.
This patch adds `isoc_alt` sysfs attribute, allowing user space
to update the alternate setting of the USB interface alternate
setting as needed.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use usb_autopm_get_interface() and usb_autopm_put_interface()
in btmtk_usb_shutdown(), it could send func ctrl after enabling
autosuspend.
Bluetooth: btmtk_usb_hci_wmt_sync() hci0: Execution of wmt command
timed out
Bluetooth: btmtk_usb_shutdown() hci0: Failed to send wmt func ctrl
(-110)
Fixes: 5c5e8c52e3 ("Bluetooth: btmtk: move btusb_mtk_[setup, shutdown] to btmtk.c")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the apparent controller hang issue seen during stress test
where the host sends a truncated payload, followed by HCI commands. The
controller treats these HCI commands as a part of previously truncated
payload, leading to command timeouts.
Adding a serdev_device_wait_until_sent() call after
serdev_device_write_buf() fixed the issue.
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_devcd_append may lead to the release of the skb, so it cannot be
accessed once it is called.
==================================================================
BUG: KASAN: slab-use-after-free in btmtk_process_coredump+0x2a7/0x2d0 [btmtk]
Read of size 4 at addr ffff888033cfabb0 by task kworker/0:3/82
CPU: 0 PID: 82 Comm: kworker/0:3 Tainted: G U 6.6.40-lockdep-03464-g1d8b4eb3060e #1 b0b3c1cc0c842735643fb411799d97921d1f688c
Hardware name: Google Yaviks_Ufs/Yaviks_Ufs, BIOS Google_Yaviks_Ufs.15217.552.0 05/07/2024
Workqueue: events btusb_rx_work [btusb]
Call Trace:
<TASK>
dump_stack_lvl+0xfd/0x150
print_report+0x131/0x780
kasan_report+0x177/0x1c0
btmtk_process_coredump+0x2a7/0x2d0 [btmtk 03edd567dd71a65958807c95a65db31d433e1d01]
btusb_recv_acl_mtk+0x11c/0x1a0 [btusb 675430d1e87c4f24d0c1f80efe600757a0f32bec]
btusb_rx_work+0x9e/0xe0 [btusb 675430d1e87c4f24d0c1f80efe600757a0f32bec]
worker_thread+0xe44/0x2cc0
kthread+0x2ff/0x3a0
ret_from_fork+0x51/0x80
ret_from_fork_asm+0x1b/0x30
</TASK>
Allocated by task 82:
stack_trace_save+0xdc/0x190
kasan_set_track+0x4e/0x80
__kasan_slab_alloc+0x4e/0x60
kmem_cache_alloc+0x19f/0x360
skb_clone+0x132/0xf70
btusb_recv_acl_mtk+0x104/0x1a0 [btusb]
btusb_rx_work+0x9e/0xe0 [btusb]
worker_thread+0xe44/0x2cc0
kthread+0x2ff/0x3a0
ret_from_fork+0x51/0x80
ret_from_fork_asm+0x1b/0x30
Freed by task 1733:
stack_trace_save+0xdc/0x190
kasan_set_track+0x4e/0x80
kasan_save_free_info+0x28/0xb0
____kasan_slab_free+0xfd/0x170
kmem_cache_free+0x183/0x3f0
hci_devcd_rx+0x91a/0x2060 [bluetooth]
worker_thread+0xe44/0x2cc0
kthread+0x2ff/0x3a0
ret_from_fork+0x51/0x80
ret_from_fork_asm+0x1b/0x30
The buggy address belongs to the object at ffff888033cfab40
which belongs to the cache skbuff_head_cache of size 232
The buggy address is located 112 bytes inside of
freed 232-byte region [ffff888033cfab40, ffff888033cfac28)
The buggy address belongs to the physical page:
page:00000000a174ba93 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x33cfa
head:00000000a174ba93 order:1 entire_mapcount:0 nr_pages_mapped:0 pincount:0
anon flags: 0x4000000000000840(slab|head|zone=1)
page_type: 0xffffffff()
raw: 4000000000000840 ffff888100848a00 0000000000000000 0000000000000001
raw: 0000000000000000 0000000080190019 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888033cfaa80: fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc
ffff888033cfab00: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb
>ffff888033cfab80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff888033cfac00: fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc
ffff888033cfac80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Check if we need to call hci_devcd_complete before calling
hci_devcd_append. That requires that we check data->cd_info.cnt >=
MTK_COREDUMP_NUM instead of data->cd_info.cnt > MTK_COREDUMP_NUM, as we
increment data->cd_info.cnt only once the call to hci_devcd_append
succeeds.
Fixes: 0b70151328 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The most significant set of changes is the per netns RTNL. The new
behavior is disabled by default, regression risk should be contained.
Notably the new config knob PTP_1588_CLOCK_VMCLOCK will inherit its
default value from PTP_1588_CLOCK_KVM, as the first is intended to be
a more reliable replacement for the latter.
Core
----
- Started a very large, in-progress, effort to make the RTNL lock
scope per network-namespace, thus reducing the lock contention
significantly in the containerized use-case, comprising:
- RCU-ified some relevant slices of the FIB control path
- introduce basic per netns locking helpers
- namespacified the IPv4 address hash table
- remove rtnl_register{,_module}() in favour of rtnl_register_many()
- refactor rtnl_{new,del,set}link() moving as much validation as
possible out of RTNL lock
- convert all phonet doit() and dumpit() handlers to RCU
- convert IPv4 addresses manipulation to per-netns RTNL
- convert virtual interface creation to per-netns RTNL
the per-netns lock infra is guarded by the CONFIG_DEBUG_NET_SMALL_RTNL
knob, disabled by default ad interim.
- Introduce NAPI suspension, to efficiently switching between busy
polling (NAPI processing suspended) and normal processing.
- Migrate the IPv4 routing input, output and control path from direct
ToS usage to DSCP macros. This is a work in progress to make ECN
handling consistent and reliable.
- Add drop reasons support to the IPv4 rotue input path, allowing
better introspection in case of packets drop.
- Make FIB seqnum lockless, dropping RTNL protection for read
access.
- Make inet{,v6} addresses hashing less predicable.
- Allow providing timestamp OPT_ID via cmsg, to correlate TX packets
and timestamps
Things we sprinkled into general kernel code
--------------------------------------------
- Add small file operations for debugfs, to reduce the struct ops size.
- Refactoring and optimization for the implementation of page_frag API,
This is a preparatory work to consolidate the page_frag
implementation.
Netfilter
---------
- Optimize set element transactions to reduce memory consumption
- Extended netlink error reporting for attribute parser failure.
- Make legacy xtables configs user selectable, giving users
the option to configure iptables without enabling any other config.
- Address a lot of false-positive RCU issues, pointed by recent
CI improvements.
BPF
---
- Put xsk sockets on a struct diet and add various cleanups. Overall,
this helps to bump performance by 12% for some workloads.
- Extend BPF selftests to increase coverage of XDP features in
combination with BPF cpumap.
- Optimize and homogenize bpf_csum_diff helper for all archs and also
add a batch of new BPF selftests for it.
- Extend netkit with an option to delegate skb->{mark,priority}
scrubbing to its BPF program.
- Make the bpf_get_netns_cookie() helper available also to tc(x) BPF
programs.
Protocols
---------
- Introduces 4-tuple hash for connected udp sockets, speeding-up
significantly connected sockets lookup.
- Add a fastpath for some TCP timers that usually expires after close,
the socket lock contention.
- Add inbound and outbound xfrm state caches to speed up state lookups.
- Avoid sending MPTCP advertisements on stale subflows, reducing
risks on loosing them.
- Make neighbours table flushing more scalable, maintaining per device
neigh lists.
Driver API
----------
- Introduce a unified interface to configure transmission H/W shaping,
and expose it to user-space via generic-netlink.
- Add support for per-NAPI config via netlink. This makes napi
configuration persistent across queues removal and re-creation.
Requires driver updates, currently supported drivers are:
nVidia/Mellanox mlx4 and mlx5, Broadcom brcm and Intel ice.
- Add ethtool support for writing SFP / PHY firmware blocks.
- Track RSS context allocation from ethtool core.
- Implement support for mirroring to DSA CPU port, via TC mirror
offload.
- Consolidate FDB updates notification, to avoid duplicates on
device-specific entries.
- Expose DPLL clock quality level to the user-space.
- Support master-slave PHY config via device tree.
Tests and tooling
-----------------
- forwarding: introduce deferred commands, to simplify
the cleanup phase
Drivers
-------
- Updated several drivers - Amazon vNic, Google vNic, Microsoft vNic,
Intel e1000e and Broadcom Tigon3 - to use netdev-genl to link the
IRQs and queues to NAPI IDs, allowing busy polling and better
introspection.
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- mlx5:
- a large refactor to implement support for cross E-Switch
scheduling
- refactor H/W conter management to let it scale better
- H/W GRO cleanups
- Intel (100G, ice)::
- adds support for ethtool reset
- implement support for per TX queue H/W shaping
- AMD/Solarflare:
- implement per device queue stats support
- Broadcom (bnxt):
- improve wildcard l4proto on IPv4/IPv6 ntuple rules
- Marvell Octeon:
- Adds representor support for each Resource Virtualization Unit
(RVU) device.
- Hisilicon:
- adds support for the BMC Gigabit Ethernet
- IBM (EMAC):
- driver cleanup and modernization
- Cisco (VIC):
- raise the queues number limit to 256
- Ethernet virtual:
- Google vNIC:
- implements page pool support
- macsec:
- inherit lower device's features and TSO limits when offloading
- virtio_net:
- enable premapped mode by default
- support for XDP socket(AF_XDP) zerocopy TX
- wireguard:
- set the TSO max size to be GSO_MAX_SIZE, to aggregate larger
packets.
- Ethernet NICs embedded and virtual:
- Broadcom ASP:
- enable software timestamping
- Freescale:
- add enetc4 PF driver
- MediaTek: Airoha SoC:
- implement BQL support
- RealTek r8169:
- enable TSO by default on r8168/r8125
- implement extended ethtool stats
- Renesas AVB:
- enable TX checksum offload
- Synopsys (stmmac):
- support header splitting for vlan tagged packets
- move common code for DWMAC4 and DWXGMAC into a separate FPE
module.
- Add the dwmac driver support for T-HEAD TH1520 SoC
- Synopsys (xpcs):
- driver refactor and cleanup
- TI:
- icssg_prueth: add VLAN offload support
- Xilinx emaclite:
- adds clock support
- Ethernet switches:
- Microchip:
- implement support for the lan969x Ethernet switch family
- add LAN9646 switch support to KSZ DSA driver
- Ethernet PHYs:
- Marvel: 88q2x: enable auto negotiation
- Microchip: add support for LAN865X Rev B1 and LAN867X Rev C1/C2
- PTP:
- Add support for the Amazon virtual clock device
- Add PtP driver for s390 clocks
- WiFi:
- mac80211
- EHT 1024 aggregation size for transmissions
- new operation to indicate that a new interface is to be added
- support radio separation of multi-band devices
- move wireless extension spy implementation to libiw
- Broadcom:
- brcmfmac: optional LPO clock support
- Microchip:
- add support for Atmel WILC3000
- Qualcomm (ath12k):
- firmware coredump collection support
- add debugfs support for a multitude of statistics
- Qualcomm (ath5k):
- Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
- Realtek:
- rtw88: 8821au and 8812au USB adapters support
- rtw89: add thermal protection
- rtw89: fine tune BT-coexsitence to improve user experience
- rtw89: firmware secure boot for WiFi 6 chip
- Bluetooth
- add Qualcomm WCN785x support for ids Foxconn 0xe0fc/0xe0f3 and
0x13d3:0x3623
- add Realtek RTL8852BE support for id Foxconn 0xe123
- add MediaTek MT7920 support for wireless module ids
- btintel_pcie: add handshake between driver and firmware
- btintel_pcie: add recovery mechanism
- btnxpuart: add GPIO support to power save feature
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=GzPr
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"The most significant set of changes is the per netns RTNL. The new
behavior is disabled by default, regression risk should be contained.
Notably the new config knob PTP_1588_CLOCK_VMCLOCK will inherit its
default value from PTP_1588_CLOCK_KVM, as the first is intended to be
a more reliable replacement for the latter.
Core:
- Started a very large, in-progress, effort to make the RTNL lock
scope per network-namespace, thus reducing the lock contention
significantly in the containerized use-case, comprising:
- RCU-ified some relevant slices of the FIB control path
- introduce basic per netns locking helpers
- namespacified the IPv4 address hash table
- remove rtnl_register{,_module}() in favour of
rtnl_register_many()
- refactor rtnl_{new,del,set}link() moving as much validation as
possible out of RTNL lock
- convert all phonet doit() and dumpit() handlers to RCU
- convert IPv4 addresses manipulation to per-netns RTNL
- convert virtual interface creation to per-netns RTNL
the per-netns lock infrastructure is guarded by the
CONFIG_DEBUG_NET_SMALL_RTNL knob, disabled by default ad interim.
- Introduce NAPI suspension, to efficiently switching between busy
polling (NAPI processing suspended) and normal processing.
- Migrate the IPv4 routing input, output and control path from direct
ToS usage to DSCP macros. This is a work in progress to make ECN
handling consistent and reliable.
- Add drop reasons support to the IPv4 rotue input path, allowing
better introspection in case of packets drop.
- Make FIB seqnum lockless, dropping RTNL protection for read access.
- Make inet{,v6} addresses hashing less predicable.
- Allow providing timestamp OPT_ID via cmsg, to correlate TX packets
and timestamps
Things we sprinkled into general kernel code:
- Add small file operations for debugfs, to reduce the struct ops
size.
- Refactoring and optimization for the implementation of page_frag
API, This is a preparatory work to consolidate the page_frag
implementation.
Netfilter:
- Optimize set element transactions to reduce memory consumption
- Extended netlink error reporting for attribute parser failure.
- Make legacy xtables configs user selectable, giving users the
option to configure iptables without enabling any other config.
- Address a lot of false-positive RCU issues, pointed by recent CI
improvements.
BPF:
- Put xsk sockets on a struct diet and add various cleanups. Overall,
this helps to bump performance by 12% for some workloads.
- Extend BPF selftests to increase coverage of XDP features in
combination with BPF cpumap.
- Optimize and homogenize bpf_csum_diff helper for all archs and also
add a batch of new BPF selftests for it.
- Extend netkit with an option to delegate skb->{mark,priority}
scrubbing to its BPF program.
- Make the bpf_get_netns_cookie() helper available also to tc(x) BPF
programs.
Protocols:
- Introduces 4-tuple hash for connected udp sockets, speeding-up
significantly connected sockets lookup.
- Add a fastpath for some TCP timers that usually expires after
close, the socket lock contention.
- Add inbound and outbound xfrm state caches to speed up state
lookups.
- Avoid sending MPTCP advertisements on stale subflows, reducing
risks on loosing them.
- Make neighbours table flushing more scalable, maintaining per
device neigh lists.
Driver API:
- Introduce a unified interface to configure transmission H/W
shaping, and expose it to user-space via generic-netlink.
- Add support for per-NAPI config via netlink. This makes napi
configuration persistent across queues removal and re-creation.
Requires driver updates, currently supported drivers are:
nVidia/Mellanox mlx4 and mlx5, Broadcom brcm and Intel ice.
- Add ethtool support for writing SFP / PHY firmware blocks.
- Track RSS context allocation from ethtool core.
- Implement support for mirroring to DSA CPU port, via TC mirror
offload.
- Consolidate FDB updates notification, to avoid duplicates on
device-specific entries.
- Expose DPLL clock quality level to the user-space.
- Support master-slave PHY config via device tree.
Tests and tooling:
- forwarding: introduce deferred commands, to simplify the cleanup
phase
Drivers:
- Updated several drivers - Amazon vNic, Google vNic, Microsoft vNic,
Intel e1000e and Broadcom Tigon3 - to use netdev-genl to link the
IRQs and queues to NAPI IDs, allowing busy polling and better
introspection.
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- mlx5:
- a large refactor to implement support for cross E-Switch
scheduling
- refactor H/W conter management to let it scale better
- H/W GRO cleanups
- Intel (100G, ice)::
- add support for ethtool reset
- implement support for per TX queue H/W shaping
- AMD/Solarflare:
- implement per device queue stats support
- Broadcom (bnxt):
- improve wildcard l4proto on IPv4/IPv6 ntuple rules
- Marvell Octeon:
- Add representor support for each Resource Virtualization Unit
(RVU) device.
- Hisilicon:
- add support for the BMC Gigabit Ethernet
- IBM (EMAC):
- driver cleanup and modernization
- Cisco (VIC):
- raise the queues number limit to 256
- Ethernet virtual:
- Google vNIC:
- implement page pool support
- macsec:
- inherit lower device's features and TSO limits when
offloading
- virtio_net:
- enable premapped mode by default
- support for XDP socket(AF_XDP) zerocopy TX
- wireguard:
- set the TSO max size to be GSO_MAX_SIZE, to aggregate larger
packets.
- Ethernet NICs embedded and virtual:
- Broadcom ASP:
- enable software timestamping
- Freescale:
- add enetc4 PF driver
- MediaTek: Airoha SoC:
- implement BQL support
- RealTek r8169:
- enable TSO by default on r8168/r8125
- implement extended ethtool stats
- Renesas AVB:
- enable TX checksum offload
- Synopsys (stmmac):
- support header splitting for vlan tagged packets
- move common code for DWMAC4 and DWXGMAC into a separate FPE
module.
- add dwmac driver support for T-HEAD TH1520 SoC
- Synopsys (xpcs):
- driver refactor and cleanup
- TI:
- icssg_prueth: add VLAN offload support
- Xilinx emaclite:
- add clock support
- Ethernet switches:
- Microchip:
- implement support for the lan969x Ethernet switch family
- add LAN9646 switch support to KSZ DSA driver
- Ethernet PHYs:
- Marvel: 88q2x: enable auto negotiation
- Microchip: add support for LAN865X Rev B1 and LAN867X Rev C1/C2
- PTP:
- Add support for the Amazon virtual clock device
- Add PtP driver for s390 clocks
- WiFi:
- mac80211
- EHT 1024 aggregation size for transmissions
- new operation to indicate that a new interface is to be added
- support radio separation of multi-band devices
- move wireless extension spy implementation to libiw
- Broadcom:
- brcmfmac: optional LPO clock support
- Microchip:
- add support for Atmel WILC3000
- Qualcomm (ath12k):
- firmware coredump collection support
- add debugfs support for a multitude of statistics
- Qualcomm (ath5k):
- Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
- Realtek:
- rtw88: 8821au and 8812au USB adapters support
- rtw89: add thermal protection
- rtw89: fine tune BT-coexsitence to improve user experience
- rtw89: firmware secure boot for WiFi 6 chip
- Bluetooth
- add Qualcomm WCN785x support for ids Foxconn 0xe0fc/0xe0f3 and
0x13d3:0x3623
- add Realtek RTL8852BE support for id Foxconn 0xe123
- add MediaTek MT7920 support for wireless module ids
- btintel_pcie: add handshake between driver and firmware
- btintel_pcie: add recovery mechanism
- btnxpuart: add GPIO support to power save feature"
* tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1475 commits)
mm: page_frag: fix a compile error when kernel is not compiled
Documentation: tipc: fix formatting issue in tipc.rst
selftests: nic_performance: Add selftest for performance of NIC driver
selftests: nic_link_layer: Add selftest case for speed and duplex states
selftests: nic_link_layer: Add link layer selftest for NIC driver
bnxt_en: Add FW trace coredump segments to the coredump
bnxt_en: Add a new ethtool -W dump flag
bnxt_en: Add 2 parameters to bnxt_fill_coredump_seg_hdr()
bnxt_en: Add functions to copy host context memory
bnxt_en: Do not free FW log context memory
bnxt_en: Manage the FW trace context memory
bnxt_en: Allocate backing store memory for FW trace logs
bnxt_en: Add a 'force' parameter to bnxt_free_ctx_mem()
bnxt_en: Refactor bnxt_free_ctx_mem()
bnxt_en: Add mem_valid bit to struct bnxt_ctx_mem_type
bnxt_en: Update firmware interface spec to 1.10.3.85
selftests/bpf: Add some tests with sockmap SK_PASS
bpf: fix recursive lock when verdict program return SK_PASS
wireguard: device: support big tcp GSO
wireguard: selftests: load nf_conntrack if not present
...
These are a number of unrelated cleanups, generally simplifying the
architecture specific header files:
- A series from Al Viro simplifies asm/vga.h, after it turns out that
most of it can be generalized.
- A series from Julian Vetter adds a common version of
memcpy_{to,from}io() and memset_io() and changes most architectures
to use that instead of their own implementation
- A series from Niklas Schnelle concludes his work to make PC
style inb()/outb() optional
- Nicolas Pitre contributes improvements for the generic do_div()
helper
- Christoph Hellwig adds a generic version of page_to_phys()
and phys_to_page(), replacing the slightly different architecture
specific definitions.
- Uwe Kleine-Koenig has a minor cleanup for ioctl definitions
-----BEGIN PGP SIGNATURE-----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=zEHk
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"These are a number of unrelated cleanups, generally simplifying the
architecture specific header files:
- A series from Al Viro simplifies asm/vga.h, after it turns out that
most of it can be generalized.
- A series from Julian Vetter adds a common version of
memcpy_{to,from}io() and memset_io() and changes most architectures
to use that instead of their own implementation
- A series from Niklas Schnelle concludes his work to make PC style
inb()/outb() optional
- Nicolas Pitre contributes improvements for the generic do_div()
helper
- Christoph Hellwig adds a generic version of page_to_phys() and
phys_to_page(), replacing the slightly different architecture
specific definitions.
- Uwe Kleine-Koenig has a minor cleanup for ioctl definitions"
* tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (24 commits)
empty include/asm-generic/vga.h
sparc: get rid of asm/vga.h
asm/vga.h: don't bother with scr_mem{cpy,move}v() unless we need to
vt_buffer.h: get rid of dead code in default scr_...() instances
tty: serial: export serial_8250_warn_need_ioport
lib/iomem_copy: fix kerneldoc format style
hexagon: simplify asm/io.h for !HAS_IOPORT
loongarch: Use new fallback IO memcpy/memset
csky: Use new fallback IO memcpy/memset
arm64: Use new fallback IO memcpy/memset
New implementation for IO memcpy and IO memset
watchdog: Add HAS_IOPORT dependency for SBC8360 and SBC7240
__arch_xprod64(): make __always_inline when optimizing for performance
ARM: div64: improve __arch_xprod_64()
asm-generic/div64: optimize/simplify __div64_const32()
lib/math/test_div64: add some edge cases relevant to __div64_const32()
asm-generic: add an optional pfn_valid check to page_to_phys
asm-generic: provide generic page_to_phys and phys_to_page implementations
asm-generic/io.h: Remove I/O port accessors for HAS_IOPORT=n
tty: serial: handle HAS_IOPORT dependencies
...
Have exception event part of HCI traces which helps for debug.
snoop traces:
> HCI Event: Vendor (0xff) plen 79
Vendor Prefix (0x8780)
Intel Extended Telemetry (0x03)
Unknown extended telemetry event type (0xde)
01 01 de
Unknown extended subevent 0x07
01 01 de 07 01 de 06 1c ef be ad de ef be ad de
ef be ad de ef be ad de ef be ad de ef be ad de
ef be ad de 05 14 ef be ad de ef be ad de ef be
ad de ef be ad de ef be ad de 43 10 ef be ad de
ef be ad de ef be ad de ef be ad de
Fixes: af395330ab ("Bluetooth: btintel: Add Intel devcoredump support")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use devm_clk_get_optional() instead of hand writing it.
This saves some LoC and improves the semantic.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The original timeout setting for HCI Reset on shutdown is 10 seconds.
HCI Reset shouldn't take 10 seconds to complete so instead use the
default timeout for commands.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
of_find_node_by_path() returns a pointer to a device_node with its
refcount incremented, and a call to of_node_put() is required to
decrement the refcount again and avoid leaking the resource.
If 'of_property_read_string_index(root, "compatible", 0, &tmp)' fails,
the function returns without calling of_node_put(root) before doing so.
The automatic cleanup attribute can be used by means of the __free()
macro to automatically call of_node_put() when the variable goes out of
scope, fixing the issue and also accounting for new error paths.
Fixes: 63fac3343b ("Bluetooth: btbcm: Support per-board firmware variants")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
pcim_iomap_regions() and pcim_iomap_table() have been deprecated in
commit e354bb84a4 ("PCI: Deprecate pcim_iomap_table(),
pcim_iomap_regions_request_all()").
Replace these functions with pcim_iomap_region().
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds quirks for broken ats2851 features.
Signed-off-by: Danil Pylaev <danstiv404@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The variable ret is being assigned -ENOMEM however this is never
read and it is being re-assigned a new value when the code jumps
to label resubmit. The assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During firmware download, vendor specific events like boot up and
secure send result are generated. These events can be safely processed at
the driver level. Passing on these events to stack prints unnecessary
log as below.
Bluetooth: hci0: Malformed MSFT vendor event: 0x02
Fixes: 3368aa357f ("Bluetooth: msft: Handle MSFT Monitor Device Event")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The switch case statement has a default branch. Thus, the return
statement at the end of the function can never be reached.
Fix it by removing the return statement at the end of the
function.
This issue was reported by Coverity Scan.
Signed-off-by: Everest K.C. <everestkc@everestkc.com.np>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use the new devm_clk_get_optional_enabled_with_rate() clock helper to
shrink the code a bit.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add DSBR support for BlazarIW, BlazarU and Gale Peak2 cores.
Refer commit eb9e749c01 ("Bluetooth: btintel: Allow configuring drive
strength of BRI") for details about DSBR.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the device tree is properly written, the SDIO function device node
should be correctly defined, and the mmc core in Linux should correctly
tie it to the device being probed.
Only fall back to searching for the device node by compatible if the
original device node tied to the device is incorrect, as seen in older
device trees.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds a recovery mechanism to recover controller if firmware
download fails due to unresponsive controller, command timeout, firmware
signature verification failure etc. Driver attmepts maximum of 5 times
before giving up.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The following handshake mechanism needs be followed after firmware
download is completed to bring the firmware to running state.
After firmware fragments of Operational image are downloaded and
secure sends result of the image succeeds,
1. Driver sends HCI Intel reset with boot option #1 to switch FW image.
2. FW sends Alive GP[0] MSIx
3. Driver enables data path (doorbell 0x460 for RBDs, etc...)
4. Driver gets Bootup event from firmware
5. Driver performs D0 entry to device (WRITE to IPC_Sleep_Control =0x0)
6. FW sends Alive GP[0] MSIx
7. Device host interface is fully set for BT protocol stack operation.
8. Driver may optionally get debug event with ID 0x97 which can be dropped
For Intermediate loadger image, all the above steps are applicable
expcept #5 and #6.
On HCI_OP_RESET, firmware raises alive interrupt. Driver needs to wait
for it before passing control over to bluetooth stack.
Co-developed-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for driving the chip into sleep or wakeup with a GPIO.
If the device tree property device-wakeup-gpios is defined, the driver
utilizes this GPIO for controlling the chip's power save state, else it
uses the default UART-break method.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This changes the chip name of IW615 to IW610.
IW610 (formerly called IW615) is yet to be released to broad market,
hence there is no issue of backward compatibility.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This updates all FW names by dropping the _v0 suffix.
Its been decided that all NXP BT/ WiFi FW names won't support _v0 suffix.
The suffix would be kept for next HW versions such as v1, v2 and so on,
which do not have backward compatible FW.
This change affects W8987, IW416 and IW615 chipsets, out of which new FW
files for W8987 and IW615 are yet to be released to broad market.
For IW416, old and new FW names are added to maintain backward
compatibility for existing customers.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Change conditions for Bluetooth driver claiming and releasing usb
ISO interface for MediaTek ISO data transmission.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
MediaTek claim an special usb intr interface for ISO data transmission.
The interface need to be released before unregistering hci device when
usb disconnect. Removing BT usb dongle without properly releasing the
interface may cause Kernel panic while unregister hci device.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add disconnect callback function in btusb_disconnect which is reserved
for vendor specific usage before deregister hci in btusb_disconnect.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move MediaTek Bluetooth power off command before releasing
usb ISO interface.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Have exception event part of HCI traces which helps for debug.
snoop traces:
> HCI Event: Vendor (0xff) plen 79
Vendor Prefix (0x8780)
Intel Extended Telemetry (0x03)
Unknown extended telemetry event type (0xde)
01 01 de
Unknown extended subevent 0x07
01 01 de 07 01 de 06 1c ef be ad de ef be ad de
ef be ad de ef be ad de ef be ad de ef be ad de
ef be ad de 05 14 ef be ad de ef be ad de ef be
ad de ef be ad de ef be ad de 43 10 ef be ad de
ef be ad de ef be ad de ef be ad de
Fixes: af395330ab ("Bluetooth: btintel: Add Intel devcoredump support")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fake CSR controllers don't seem to handle short-transfer properly which
cause command to time out:
kernel: usb 1-1: new full-speed USB device number 19 using xhci_hcd
kernel: usb 1-1: New USB device found, idVendor=0a12, idProduct=0001, bcdDevice=88.91
kernel: usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
kernel: usb 1-1: Product: BT DONGLE10
...
Bluetooth: hci1: Opcode 0x1004 failed: -110
kernel: Bluetooth: hci1: command 0x1004 tx timeout
According to USB Spec 2.0 Section 5.7.3 Interrupt Transfer Packet Size
Constraints a interrupt transfer is considered complete when the size is 0
(ZPL) or < wMaxPacketSize:
'When an interrupt transfer involves more data than can fit in one
data payload of the currently established maximum size, all data
payloads are required to be maximum-sized except for the last data
payload, which will contain the remaining data. An interrupt transfer
is complete when the endpoint does one of the following:
• Has transferred exactly the amount of data expected
• Transfers a packet with a payload size less than wMaxPacketSize or
transfers a zero-length packet'
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219365
Fixes: 7b05933340 ("Bluetooth: btusb: Fix not handling ZPL/short-transfer")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This partially reverts 81b3e33bb054 ("Bluetooth: btusb: Don't fail
external suspend requests") as it introduced a call to hci_suspend_dev
that assumes the system-suspend which doesn't work well when just the
device is being suspended because wakeup flag is only set for remote
devices that can wakeup the system.
Reported-by: Rafael J. Wysocki <rafael@kernel.org>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Kenneth Crudup <kenny@panix.com>
Fixes: 610712298b ("Bluetooth: btusb: Don't fail external suspend requests")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Rafael J. Wysocki <rafael@kernel.org>
Commit 4e0a1d8b06
("Bluetooth: btusb: Don't suspend when there are connections")
introduces a check for connections to prevent auto-suspend but that
actually ignored the fact the .suspend callback can be called for
external suspend requests which
Documentation/driver-api/usb/power-management.rst states the following:
'External suspend calls should never be allowed to fail in this way,
only autosuspend calls. The driver can tell them apart by applying
the :c:func:`PMSG_IS_AUTO` macro to the message argument to the
``suspend`` method; it will return True for internal PM events
(autosuspend) and False for external PM events.'
In addition to that align system suspend with USB suspend by using
hci_suspend_dev since otherwise the stack would be expecting events
such as advertising reports which may not be delivered while the
transport is suspended.
Fixes: 4e0a1d8b06 ("Bluetooth: btusb: Don't suspend when there are connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Kiran K <kiran.k@intel.com>
Current release - regressions:
- eth: mlx5: fix wrong reserved field in hca_cap_2 in mlx5_ifc
- eth: am65-cpsw: fix forever loop in cleanup code
Current release - new code bugs:
- eth: mlx5: HWS, fixed double-free in error flow of creating SQ
Previous releases - regressions:
- core: avoid potential underflow in qdisc_pkt_len_init() with UFO
- core: test for not too small csum_start in virtio_net_hdr_to_skb()
- vrf: revert "vrf: remove unnecessary RCU-bh critical section"
- bluetooth:
- fix uaf in l2cap_connect
- fix possible crash on mgmt_index_removed
- dsa: improve shutdown sequence
- eth: mlx5e: SHAMPO, fix overflow of hd_per_wq
- eth: ip_gre: fix drops of small packets in ipgre_xmit
Previous releases - always broken:
- core: fix gso_features_check to check for both dev->gso_{ipv4_,}max_size
- core: fix tcp fraglist segmentation after pull from frag_list
- netfilter: nf_tables: prevent nf_skb_duplicated corruption
- sctp: set sk_state back to CLOSED if autobind fails in sctp_listen_start
- mac802154: fix potential RCU dereference issue in mac802154_scan_worker
- eth: fec: restart PPS after link state change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=cq2I
-----END PGP SIGNATURE-----
Merge tag 'net-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from ieee802154, bluetooth and netfilter.
Current release - regressions:
- eth: mlx5: fix wrong reserved field in hca_cap_2 in mlx5_ifc
- eth: am65-cpsw: fix forever loop in cleanup code
Current release - new code bugs:
- eth: mlx5: HWS, fixed double-free in error flow of creating SQ
Previous releases - regressions:
- core: avoid potential underflow in qdisc_pkt_len_init() with UFO
- core: test for not too small csum_start in virtio_net_hdr_to_skb()
- vrf: revert "vrf: remove unnecessary RCU-bh critical section"
- bluetooth:
- fix uaf in l2cap_connect
- fix possible crash on mgmt_index_removed
- dsa: improve shutdown sequence
- eth: mlx5e: SHAMPO, fix overflow of hd_per_wq
- eth: ip_gre: fix drops of small packets in ipgre_xmit
Previous releases - always broken:
- core: fix gso_features_check to check for both
dev->gso_{ipv4_,}max_size
- core: fix tcp fraglist segmentation after pull from frag_list
- netfilter: nf_tables: prevent nf_skb_duplicated corruption
- sctp: set sk_state back to CLOSED if autobind fails in
sctp_listen_start
- mac802154: fix potential RCU dereference issue in
mac802154_scan_worker
- eth: fec: restart PPS after link state change"
* tag 'net-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (48 commits)
sctp: set sk_state back to CLOSED if autobind fails in sctp_listen_start
dt-bindings: net: xlnx,axi-ethernet: Add missing reg minItems
doc: net: napi: Update documentation for napi_schedule_irqoff
net/ncsi: Disable the ncsi work before freeing the associated structure
net: phy: qt2025: Fix warning: unused import DeviceId
gso: fix udp gso fraglist segmentation after pull from frag_list
bridge: mcast: Fail MDB get request on empty entry
vrf: revert "vrf: Remove unnecessary RCU-bh critical section"
net: ethernet: ti: am65-cpsw: Fix forever loop in cleanup code
net: phy: realtek: Check the index value in led_hw_control_get
ppp: do not assume bh is held in ppp_channel_bridge_input()
selftests: rds: move include.sh to TEST_FILES
net: test for not too small csum_start in virtio_net_hdr_to_skb()
net: gso: fix tcp fraglist segmentation after pull from frag_list
ipv4: ip_gre: Fix drops of small packets in ipgre_xmit
net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check
net: add more sanity checks to qdisc_pkt_len_init()
net: avoid potential underflow in qdisc_pkt_len_init() with UFO
net: ethernet: ti: cpsw_ale: Fix warning on some platforms
net: microchip: Make FDMA config symbol invisible
...
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: bb7f4f0bce ("btmrvl: add platform specific wakeup interrupt support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix driver not allocating memory for struct btintel_data which is used
to store internal data.
Fixes: 6e65a09f92 ("Bluetooth: btintel_pcie: Add *setup* function to download firmware")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Requesting transfers of the exact same size of wMaxPacketSize may result
in ZPL/short-transfer since the USB stack cannot handle it as we are
limiting the buffer size to be the same as wMaxPacketSize.
Also, in terms of throughput this change has the same effect to
interrupt endpoint as 290ba20081 "Bluetooth: Improve USB driver throughput
by increasing the frame size" had for the bulk endpoint, so users of the
advertisement bearer (e.g. BT Mesh) may benefit from this change.
Fixes: 5e23b923da ("[Bluetooth] Add generic driver for Bluetooth USB devices")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Kiran K <kiran.k@intel.com>
CYW4373 devices soldered onto the PCB (non-removable),
use a UART connection for Bluetooth and the advertised btsdio
support as an SDIO function should be ignored.
Signed-off-by: Scott Ehlert <ehlert@battelle.org>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For tracking multiple devices concurrently with a condition.
The patch enables the HCI_QUIRK_USE_MSFT_EXT_ADDRESS_FILTER quirk
on RTL8852B controller.
The quirk setting is based on commit 9e14606d8f ("Bluetooth: msft:
Extended monitor tracking by address filter")
With this setting, when a pattern monitor detects a device, this
feature issues an address monitor for tracking that device. Let the
original pattern monitor keep monitor new devices.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use kvmemdup instead of kvmalloc() + memcpy() to simplify the code.
No functional change intended.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
