Document two optional cells in eswin,hsp-sp-csr for the TXD and RXD
delay control register offsets.
These registers are used by the driver to clear any residual delay
configuration left by the bootloader, ensuring that MAC-side RGMII delay
settings are applied solely according to the kernel configuration.
Add a reference to the EIC7700X SoC Technical Reference Manual for
background information about the HSP CSR block.
Fixes: 888bd0eca9 ("dt-bindings: ethernet: eswin: Document for EIC7700 SoC")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260518022023.427-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for the Milos SoC, which uses IPA v5.2.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://patch.msgid.link/20260410-ipa-v5-2-v2-1-778422a05060@fairphone.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This MDIO hardware is based on a Microsemi design supported in Linux by
mdio-mscc-miim.c. However, The register interface is completely different
with pic64hpsc, hence the need for separate documentation.
The hardware supports C22 and C45.
The documentation recommends an input clock of 156.25MHz and a prescaler
of 39, which yields an MDIO clock of 1.95MHz.
The hardware supports an interrupt pin to signal transaction completion
which is not strictly needed as the software can also poll a "TRIGGER"
bit for this.
Signed-off-by: Charles Perry <charles.perry@microchip.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260408131821.1145334-2-charles.perry@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the binding requires 'spi-cpha' for SJA1105 and 'spi-cpol'
for SJA1110.
However, the SJA1110 supports both SPI modes 0 and 2. Mode 2
(cpha=0, cpol=1) is used by the NXP LX2160 Bluebox 3.
On the SolidRun i.MX8DXL HummingBoard Telematics, mode 0 is stable,
while forcing mode 2 introduces CRC errors especially during bursts.
Drop the requirement on spi-cpol for SJA1110.
Fixes: af2eab1a82 ("dt-bindings: net: nxp,sja1105: document spi-cpol/cpha")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260409-imx8dxl-sr-som-v2-1-83ff20629ba0@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- crypto: move Michael MIC code into wireless (only)
- mac80211:
- multi-link 4-addr support
- NAN data support (but no drivers yet)
- ath10k: DT quirk to make it work on some devices
- ath12k: IPQ5424 support
- rtw89: USB improvements for performance
-----BEGIN PGP SIGNATURE-----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=lf+O
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-04-10' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Final updates, notably:
- crypto: move Michael MIC code into wireless (only)
- mac80211:
- multi-link 4-addr support
- NAN data support (but no drivers yet)
- ath10k: DT quirk to make it work on some devices
- ath12k: IPQ5424 support
- rtw89: USB improvements for performance
* tag 'wireless-next-2026-04-10' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (124 commits)
wifi: cfg80211: Explicitly include <linux/export.h> in michael-mic.c
wifi: ath10k: Add device-tree quirk to skip host cap QMI requests
dt-bindings: wireless: ath10k: Add quirk to skip host cap QMI requests
crypto: Remove michael_mic from crypto_shash API
wifi: ipw2x00: Use michael_mic() from cfg80211
wifi: ath12k: Use michael_mic() from cfg80211
wifi: ath11k: Use michael_mic() from cfg80211
wifi: mac80211, cfg80211: Export michael_mic() and move it to cfg80211
wifi: ipw2x00: Rename michael_mic() to libipw_michael_mic()
wifi: libertas_tf: refactor endpoint lookup
wifi: libertas: refactor endpoint lookup
wifi: at76c50x: refactor endpoint lookup
wifi: ath12k: Enable IPQ5424 WiFi device support
wifi: ath12k: Add CE remap hardware parameters for IPQ5424
wifi: ath12k: add ath12k_hw_regs for IPQ5424
wifi: ath12k: add ath12k_hw_version_map entry for IPQ5424
wifi: ath12k: Add ath12k_hw_params for IPQ5424
dt-bindings: net: wireless: add ath12k wifi device IPQ5424
wifi: ath10k: fix station lookup failure during disconnect
wifi: ath12k: Create symlink for each radio in a wiphy
...
====================
Link: https://patch.msgid.link/20260410064703.735099-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The J722S CPSW3G is mostly identical to the AM64's, but additionally
supports SGMII. The AM64 compatible ti,am642-cpsw-nuss is used as a
fallback.
Signed-off-by: Nora Schiffer <nora.schiffer@ew.tq-group.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/191e9f7e3a6c14eabe891a98c5fb646766479c0a.1775558273.git.nora.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document support for spread spectrum clocking (SSC) on RTL8211F(D)(I)-CG,
RTL8211FS(I)(-VS)-CG, RTL8211FG(I)(-VS)-CG PHYs. Introduce DT properties
'realtek,clkout-ssc-enable', 'realtek,rxc-ssc-enable' and
'realtek,sysclk-ssc-enable' which control CLKOUT, RXC and SYSCLK
SSC spread spectrum clocking enablement on these signals. These
clock are not exposed via the clock API, therefore assigned-clock-sscs
property does not apply.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Link: https://patch.msgid.link/20260405233008.148974-2-marek.vasut@mailbox.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sort the documented properties alphabetically, no functional change.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Link: https://patch.msgid.link/20260405233008.148974-1-marek.vasut@mailbox.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some firmware versions do not support the host-capability QMI request.
Since this request occurs before firmware and board files are loaded,
the quirk cannot be expressed in the firmware itself and must be described
in the device tree.
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Co-developed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260407-skip-host-cam-qmi-req-v5-1-dfa8a05c6538@ixit.cz
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the device-tree bindings for the ATH12K AHB wifi device IPQ5424.
Signed-off-by: Raj Kumar Bhagat <raj.bhagat@oss.qualcomm.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20260407-ath12k-ipq5424-v5-1-8e96aa660ec4@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The PN557 uses the same hardware as the PN553 but ships with
firmware compliant with NCI 2.0.
Document PN557 as a compatible device.
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260403-oneplus-nfc-v3-1-fbdce57d63c1@ixit.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP clock for the Tegra234 MGBE device is incorrectly named
'ptp-ref' and should be 'ptp_ref'. This is causing the following
warning to be observed on Tegra234 platforms that use this device:
ERR KERN tegra-mgbe 6800000.ethernet eth0: Invalid PTP clock rate
WARNING KERN tegra-mgbe 6800000.ethernet eth0: PTP init failed
Although this constitutes an ABI breakage in the binding for this
device, PTP support has clearly never worked and so fix this now
so we can correct the device-tree for this device. Note that the
MGBE driver still supports the legacy 'ptp-ref' clock name and so
older/existing device-trees will still work, but given that this
is not the correct name, there is no point to advertise this in the
binding.
Fixes: 189c2e5c76 ("dt-bindings: net: Add Tegra234 MGBE")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260401102941.17466-3-jonathanh@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the boolean property 'microchip,xstbyen' to enable the dedicated
transceiver standby control function on the INT0/GPIO0/XSTBY pin of
the MCP251xFD family.
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260321135031.3107408-2-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The GEM IP has two methods for modifying the ptp timer. The first of
these, named "increment mode", relies on software controlling the timer
by setting tsu_timer_incr and tsu_timer_incr_sub_nsec and performing
once-off adjustments via the tsu_timer_adjust register. This is what the
macb driver uses. The second mechanism, "timer adjust mode" uses the
gem_tsu_inc_ctrl and gem_tsu_ms signals to control the timer. These
modes are not intended to be used in parallel, but both can be possible
on the same device and which mode is used cannot be determined from the
compatible on all devices, because some users of the GEM IP are SoC
FPGAs that permit configuring how the IP is wired up.
Add a property to indicate that gem_tsu_inc_ctrl and gem_tsu_ms are wired
up for timer adjust mode.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260325-daily-entitle-3640f7254da4@spud
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ryan added cdns,refclk-ext with the intent of decoupling the source of
the reference clock on sama7g5 (and related platforms) from the
compatible. Unfortunately, the default for sama7g5-emac is an external
reference clock, so this property had no effect there, so that
compatibility with older devicetrees is preserved.
Replace cdns,refclk-ext with one that supports both default states and
therefore is usable for sama7g5-emac.
For now, limit it to only the platforms that have USRIO controlled
reference clock selection, but this could be generalised in the future.
The existing property only works on devices that are compatible with
sama7g5-gem, so mark it deprecated, and limit its use to that specific
scenario.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260325-savior-untainted-03057ee0a917@spud
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the AXI snps,kbbe snps,mb and snps,rb properties as they have
not been used, and although the driver parses these, the code hasn't
ever used the parsed result. This parsing has now been removed.
These were introduced by commit afea03656a ("stmmac: rework DMA bus
setting and introduce new platform AXI structure").
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/E1w4ydt-0000000Dlph-3WvI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create initial schema for Nuvoton MA35 family Gigabit MAC.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Joey Lu <a0987203069@gmail.com>
Link: https://patch.msgid.link/20260323101756.81849-2-a0987203069@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the property enet-phy-pair-polarity to describe the polarity of the
PHY pairs. To ease PCB designs some manufacturers allow to wire the
pairs with a reverse polarity and provide a way to configure it.
The property 'enet-phy-pair-polarity' sets the polarity of each pair.
Bit 0 to 3 configure the polarity or pairs A to D, if set to 1 the
polarity is reversed for this pair.
Signed-off-by: Damien Dejean <dam.dejean@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260318215502.106528-4-dam.dejean@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add property enet-phy-pair-order to the device tree bindings to define
the pair order of the PHY. To simplify PCB design some manufacturers
allow to wire the pairs in a reverse order, and change the order in
software.
The property can be set to 0 to force the normal pair order (ABCD), or 1
to force the reverse pair order (DCBA).
Signed-off-by: Damien Dejean <dam.dejean@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260318215502.106528-2-dam.dejean@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Micrel KSZ8041RNLI supports LED mode, just like KSZ8041.
This fixes (a.o.) the following "make dtbs_check" warning:
arch/arm/boot/dts/renesas/r8a7791-koelsch.dtb: ethernet-phy@1 (ethernet-phy-id0022.1537): False schema does not allow 1
from schema $id: http://devicetree.org/schemas/net/micrel.yaml
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stefan Eichenberger <eichest@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/efad6c7e024b3a9aa2882db65909ee5bbbcbdc45.1773734298.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The GMAC IP on Spacemit K3 is almost a standard Synopsys DesignWare
MAC (version 5.40a) with some extra clock.
Add necessary compatible string for this device.
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260316010041.164360-2-inochiama@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add "microchip,pic64hpsc-gem" for "PIC64-HPSC" and
"microchip,pic64hx-gem" for "PIC64HX", compatible with the former.
The generic compatible "cdns,gem" works but offers limited features.
Keep it as a fallback.
The GEM IPs within pic64hpsc have their MDIO controllers unconnected
from any physical pin. Add a check to prevent adding PHYs under the GEM
node.
Signed-off-by: Charles Perry <charles.perry@microchip.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260313140610.3681752-2-charles.perry@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DWMAC IP on NXP S32G/R SoCs has connected queue-based IRQ lines,
set them to allow using Multi-IRQ mode.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20260313-dwmac_multi_irq-v12-3-b5c9d0aa13d6@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document that ipa on qcm2290 uses version 4.2, the same
as sc7180.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wojciech Slenska <wojciech.slenska@gmail.com>
Link: https://patch.msgid.link/20260310112309.79261-2-wojciech.slenska@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR (net-7.0-rc3).
No conflicts.
Adjacent changes:
net/netfilter/nft_set_rbtree.c
fb7fb40163 ("netfilter: nf_tables: clone set on flush only")
3aea466a43 ("netfilter: nft_set_rbtree: don't disable bh when acquiring tree lock")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ports in the example device tree should not have a 'label'
property. Labels for all user ports have been removed from an earlier
submission, but this was overlooked in the case of the CPU port.
Remove 'cpu' port label from the example.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/61579de297eb636ec5f1e6c97d453e26abb0625d.1772507210.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA driver currently grabs a slice of IMEM through hardcoded
addresses. Not only is that ugly and against the principles of DT,
but it also creates a situation where two distinct platforms
implementing the same version of IPA would need to be hardcoded
together and matched at runtime.
Instead, do the sane thing and accept a handle to said region directly.
Don't make it required on purpose, as it's not there on ancient
implementations (currently unsupported) and we're not yet done with
filling the data across al DTs.
Reviewed-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260302-topic-ipa_imem-v6-2-c0ebbf3eae9f@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a reference to mc-peripheral-props.yaml to allow vendor-specific
properties for memory access timings.
Fix below CHECK_DTBS warings:
arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-rdk.dtb: can@4,0 (nxp,sja1000): Unevaluated properties are not allowed ('fsl,weim-cs-timing' was unexpected)
from schema $id: http://devicetree.org/schemas/net/can/nxp,sja1000.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260212163000.1195586-1-Frank.Li@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Core & protocols
----------------
- A significant effort all around the stack to guide the compiler to
make the right choice when inlining code, to avoid unneeded calls for
small helper and stack canary overhead in the fast-path. This
generates better and faster code with very small or no text size
increases, as in many cases the call generated more code than the
actual inlined helper.
- Extend AccECN implementation so that is now functionally complete,
also allow the user-space enabling it on a per network namespace
basis.
- Add support for memory providers with large (above 4K) rx buffer.
Paired with hw-gro, larger rx buffer sizes reduce the number of
buffers traversing the stack, dincreasing single stream CPU usage by
up to ~30%.
- Do not add HBH header to Big TCP GSO packets. This simplifies the RX
path, the TX path and the NIC drivers, and is possible because
user-space taps can now interpret correctly such packets without the
HBH hint.
- Allow IPv6 routes to be configured with a gateway address that is
resolved out of a different interface than the one specified, aligning
IPv6 to IPv4 behavior.
- Multi-queue aware sch_cake. This makes it possible to scale the rate
shaper of sch_cake across multiple CPUs, while still enforcing a
single global rate on the interface.
- Add support for the nbcon (new buffer console) infrastructure to
netconsole, enabling lock-free, priority-based console operations that
are safer in crash scenarios.
- Improve the TCP ipv6 output path to cache the flow information, saving
cpu cycles, reducing cache line misses and stack use.
- Improve netfilter packet tracker to resolve clashes for most protocols,
avoiding unneeded drops on rare occasions.
- Add IP6IP6 tunneling acceleration to the flowtable infrastructure.
- Reduce tcp socket size by one cache line.
- Notify neighbour changes atomically, avoiding inconsistencies between
the notification sequence and the actual states sequence.
- Add vsock namespace support, allowing complete isolation of vsocks
across different network namespaces.
- Improve xsk generic performances with cache-alignment-oriented
optimizations.
- Support netconsole automatic target recovery, allowing netconsole
to reestablish targets when underlying low-level interface comes back
online.
Driver API
----------
- Support for switching the working mode (automatic vs manual) of a DPLL
device via netlink.
- Introduce PHY ports representation to expose multiple front-facing
media ports over a single MAC.
- Introduce "rx-polarity" and "tx-polarity" device tree properties, to
generalize polarity inversion requirements for differential signaling.
- Add helper to create, prepare and enable managed clocks.
Device drivers
--------------
- Add Huawei hinic3 PF etherner driver.
- Add DWMAC glue driver for Motorcomm YT6801 PCIe ethernet controller.
- Add ethernet driver for MaxLinear MxL862xx switches
- Remove parallel-port Ethernet driver.
- Convert existing driver timestamp configuration reporting to
hwtstamp_get and remove legacy ioctl().
- Convert existing drivers to .get_rx_ring_count(), simplifing the RX
ring count retrieval. Also remove the legacy fallback path.
- Ethernet high-speed NICs:
- Broadcom (bnxt, bng):
- bnxt: add FW interface update to support FEC stats histogram and
NVRAM defragmentation
- bng: add TSO and H/W GRO support
- nVidia/Mellanox (mlx5):
- improve latency of channel restart operations, reducing the used
H/W resources
- add TSO support for UDP over GRE over VLAN
- add flow counters support for hardware steering (HWS) rules
- use a static memory area to store headers for H/W GRO, leading to
12% RX tput improvement
- Intel (100G, ice, idpf):
- ice: reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new layouts
- ice: introduces Synchronous Ethernet (SyncE) support
- Meta (fbnic):
- adds debugfs for firmware mailbox and tx/rx rings vectors
- Ethernet virtual:
- geneve: introduce GRO/GSO support for double UDP encapsulation
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- some code refactoring and cleanups
- RealTek (r8169):
- add support for RTL8127ATF (10G Fiber SFP)
- add dash and LTR support
- Airoha:
- AN8811HB 2.5 Gbps phy support
- Freescale (fec):
- add XDP zero-copy support
- Thunderbolt:
- add get link setting support to allow bonding
- Renesas:
- add support for RZ/G3L GBETH SoC
- Ethernet switches:
- Maxlinear:
- support R(G)MII slow rate configuration
- add support for Intel GSW150
- Motorcomm (yt921x):
- add DCB/QoS support
- TI:
- icssm-prueth: support bridging (STP/RSTP) via the switchdev
framework
- Ethernet PHYs:
- Realtek:
- enable SGMII and 2500Base-X in-band auto-negotiation
- simplify and reunify C22/C45 drivers
- Micrel: convert bindings to DT schema
- CAN:
- move skb headroom content into skb extensions, making CAN metadata
access more robust
- CAN drivers:
- rcar_canfd:
- add support for FD-only mode
- add support for the RZ/T2H SoC
- sja1000: cleanup the CAN state handling
- WiFi:
- implement EPPKE/802.1X over auth frames support
- split up drop reasons better, removing generic RX_DROP
- additional FTM capabilities: 6 GHz support, supported number of
spatial streams and supported number of LTF repetitions
- better mac80211 iterators to enumerate resources
- initial UHR (Wi-Fi 8) support for cfg80211/mac80211
- WiFi drivers:
- Qualcomm/Atheros:
- ath11k: support for Channel Frequency Response measurement
- ath12k: a significant driver refactor to support
multi-wiphy devices and and pave the way for future device support
in the same driver (rather than splitting to ath13k)
- ath12k: support for the QCC2072 chipset
- Intel:
- iwlwifi: partial Neighbor Awareness Networking (NAN) support
- iwlwifi: initial support for U-NII-9 and IEEE 802.11bn
- RealTek (rtw89):
- preparations for RTL8922DE support
- Bluetooth:
- implement setsockopt(BT_PHY) to set the connection packet type/PHY
- set link_policy on incoming ACL connections
- Bluetooth drivers:
- btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE
- btqca: add WCN6855 firmware priority selection feature
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=O31Y
-----END PGP SIGNATURE-----
Merge tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core & protocols:
- A significant effort all around the stack to guide the compiler to
make the right choice when inlining code, to avoid unneeded calls
for small helper and stack canary overhead in the fast-path.
This generates better and faster code with very small or no text
size increases, as in many cases the call generated more code than
the actual inlined helper.
- Extend AccECN implementation so that is now functionally complete,
also allow the user-space enabling it on a per network namespace
basis.
- Add support for memory providers with large (above 4K) rx buffer.
Paired with hw-gro, larger rx buffer sizes reduce the number of
buffers traversing the stack, dincreasing single stream CPU usage
by up to ~30%.
- Do not add HBH header to Big TCP GSO packets. This simplifies the
RX path, the TX path and the NIC drivers, and is possible because
user-space taps can now interpret correctly such packets without
the HBH hint.
- Allow IPv6 routes to be configured with a gateway address that is
resolved out of a different interface than the one specified,
aligning IPv6 to IPv4 behavior.
- Multi-queue aware sch_cake. This makes it possible to scale the
rate shaper of sch_cake across multiple CPUs, while still enforcing
a single global rate on the interface.
- Add support for the nbcon (new buffer console) infrastructure to
netconsole, enabling lock-free, priority-based console operations
that are safer in crash scenarios.
- Improve the TCP ipv6 output path to cache the flow information,
saving cpu cycles, reducing cache line misses and stack use.
- Improve netfilter packet tracker to resolve clashes for most
protocols, avoiding unneeded drops on rare occasions.
- Add IP6IP6 tunneling acceleration to the flowtable infrastructure.
- Reduce tcp socket size by one cache line.
- Notify neighbour changes atomically, avoiding inconsistencies
between the notification sequence and the actual states sequence.
- Add vsock namespace support, allowing complete isolation of vsocks
across different network namespaces.
- Improve xsk generic performances with cache-alignment-oriented
optimizations.
- Support netconsole automatic target recovery, allowing netconsole
to reestablish targets when underlying low-level interface comes
back online.
Driver API:
- Support for switching the working mode (automatic vs manual) of a
DPLL device via netlink.
- Introduce PHY ports representation to expose multiple front-facing
media ports over a single MAC.
- Introduce "rx-polarity" and "tx-polarity" device tree properties,
to generalize polarity inversion requirements for differential
signaling.
- Add helper to create, prepare and enable managed clocks.
Device drivers:
- Add Huawei hinic3 PF etherner driver.
- Add DWMAC glue driver for Motorcomm YT6801 PCIe ethernet
controller.
- Add ethernet driver for MaxLinear MxL862xx switches
- Remove parallel-port Ethernet driver.
- Convert existing driver timestamp configuration reporting to
hwtstamp_get and remove legacy ioctl().
- Convert existing drivers to .get_rx_ring_count(), simplifing the RX
ring count retrieval. Also remove the legacy fallback path.
- Ethernet high-speed NICs:
- Broadcom (bnxt, bng):
- bnxt: add FW interface update to support FEC stats histogram
and NVRAM defragmentation
- bng: add TSO and H/W GRO support
- nVidia/Mellanox (mlx5):
- improve latency of channel restart operations, reducing the
used H/W resources
- add TSO support for UDP over GRE over VLAN
- add flow counters support for hardware steering (HWS) rules
- use a static memory area to store headers for H/W GRO,
leading to 12% RX tput improvement
- Intel (100G, ice, idpf):
- ice: reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new
layouts
- ice: introduces Synchronous Ethernet (SyncE) support
- Meta (fbnic):
- adds debugfs for firmware mailbox and tx/rx rings vectors
- Ethernet virtual:
- geneve: introduce GRO/GSO support for double UDP encapsulation
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- some code refactoring and cleanups
- RealTek (r8169):
- add support for RTL8127ATF (10G Fiber SFP)
- add dash and LTR support
- Airoha:
- AN8811HB 2.5 Gbps phy support
- Freescale (fec):
- add XDP zero-copy support
- Thunderbolt:
- add get link setting support to allow bonding
- Renesas:
- add support for RZ/G3L GBETH SoC
- Ethernet switches:
- Maxlinear:
- support R(G)MII slow rate configuration
- add support for Intel GSW150
- Motorcomm (yt921x):
- add DCB/QoS support
- TI:
- icssm-prueth: support bridging (STP/RSTP) via the switchdev
framework
- Ethernet PHYs:
- Realtek:
- enable SGMII and 2500Base-X in-band auto-negotiation
- simplify and reunify C22/C45 drivers
- Micrel: convert bindings to DT schema
- CAN:
- move skb headroom content into skb extensions, making CAN
metadata access more robust
- CAN drivers:
- rcar_canfd:
- add support for FD-only mode
- add support for the RZ/T2H SoC
- sja1000: cleanup the CAN state handling
- WiFi:
- implement EPPKE/802.1X over auth frames support
- split up drop reasons better, removing generic RX_DROP
- additional FTM capabilities: 6 GHz support, supported number of
spatial streams and supported number of LTF repetitions
- better mac80211 iterators to enumerate resources
- initial UHR (Wi-Fi 8) support for cfg80211/mac80211
- WiFi drivers:
- Qualcomm/Atheros:
- ath11k: support for Channel Frequency Response measurement
- ath12k: a significant driver refactor to support multi-wiphy
devices and and pave the way for future device support in the
same driver (rather than splitting to ath13k)
- ath12k: support for the QCC2072 chipset
- Intel:
- iwlwifi: partial Neighbor Awareness Networking (NAN) support
- iwlwifi: initial support for U-NII-9 and IEEE 802.11bn
- RealTek (rtw89):
- preparations for RTL8922DE support
- Bluetooth:
- implement setsockopt(BT_PHY) to set the connection packet type/PHY
- set link_policy on incoming ACL connections
- Bluetooth drivers:
- btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE
- btqca: add WCN6855 firmware priority selection feature"
* tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1254 commits)
bnge/bng_re: Add a new HSI
net: macb: Fix tx/rx malfunction after phy link down and up
af_unix: Fix memleak of newsk in unix_stream_connect().
net: ti: icssg-prueth: Add optional dependency on HSR
net: dsa: add basic initial driver for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add tag format for MxL862xx switches
dt-bindings: net: dsa: add MaxLinear MxL862xx
selftests: drivers: net: hw: Modify toeplitz.c to poll for packets
octeontx2-pf: Unregister devlink on probe failure
net: renesas: rswitch: fix forwarding offload statemachine
ionic: Rate limit unknown xcvr type messages
tcp: inet6_csk_xmit() optimization
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_syn_recv_sock()
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_connect()
ipv6: inet6_csk_xmit() and inet6_csk_update_pmtu() use inet->cork.fl.u.ip6
ipv6: use inet->cork.fl.u.ip6 and np->final in ip6_datagram_dst_update()
ipv6: use np->final in inet6_sk_rebuild_header()
ipv6: add daddr/final storage in struct ipv6_pinfo
net: stmmac: qcom-ethqos: fix qcom_ethqos_serdes_powerup()
...
DT core:
- Sync dtc/libfdt with upstream v1.7.2-62-ga26ef6400bd8
- Add a for_each_compatible_node_scoped() loop and convert users in
cpufreq, dmaengine, clk, cdx, powerpc and Arm
- Simplify of/platform.c with scoped loop helpers
- Add fw_devlink tracking for "mmc-pwrseq"
- Optimize fw_devlink callback code size for pinctrl-N properties
- Replace strcmp_suffix() with strends()
DT bindings:
- Support building single binding targets
- Convert google,goldfish-fb, cznic,turris-mox-rwtm, ti,prm-inst
- Add bindings for Freescale AVIC, Realtek RTD1xxx system controllers,
Microchip 25AA010A EEPROM, OnSemi FIN3385, IEI WT61P803 PUZZLE, Delta
Electronics DPS-800-AB power supply, Infineon IR35221 Digital
Multi-phase Controller, Infineon PXE1610 Digital Dual Output 6+1
VR12.5 & VR13 CPU Controller, socionext,uniphier-smpctrl, and
xlnx,zynqmp-firmware
- Lots of trivial binding fixes to address warnings in DTS files. These
are mostly for arm64 platforms which is getting closer to be warning
free. Some public shaming has helped.
- Fix I2C bus node names in examples
- Drop obsolete brcm,vulcan-soc binding
- Drop unreferenced binding headers
-----BEGIN PGP SIGNATURE-----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=RE7t
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT core:
- Sync dtc/libfdt with upstream v1.7.2-62-ga26ef6400bd8
- Add a for_each_compatible_node_scoped() loop and convert users in
cpufreq, dmaengine, clk, cdx, powerpc and Arm
- Simplify of/platform.c with scoped loop helpers
- Add fw_devlink tracking for "mmc-pwrseq"
- Optimize fw_devlink callback code size for pinctrl-N properties
- Replace strcmp_suffix() with strends()
DT bindings:
- Support building single binding targets
- Convert google,goldfish-fb, cznic,turris-mox-rwtm, ti,prm-inst
- Add bindings for Freescale AVIC, Realtek RTD1xxx system
controllers, Microchip 25AA010A EEPROM, OnSemi FIN3385, IEI
WT61P803 PUZZLE, Delta Electronics DPS-800-AB power supply,
Infineon IR35221 Digital Multi-phase Controller, Infineon PXE1610
Digital Dual Output 6+1 VR12.5 & VR13 CPU Controller,
socionext,uniphier-smpctrl, and xlnx,zynqmp-firmware
- Lots of trivial binding fixes to address warnings in DTS files.
These are mostly for arm64 platforms which is getting closer to be
warning free. Some public shaming has helped.
- Fix I2C bus node names in examples
- Drop obsolete brcm,vulcan-soc binding
- Drop unreferenced binding headers"
* tag 'devicetree-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (60 commits)
dt-bindings: interrupt-controller: Add compatiblie string fsl,imx(1|25|27|31|35)-avic
dt-bindings: soc: imx: add fsl,aips and fsl,emi compatible strings
dt-bindings: display: bridge: lt8912b: Drop reset gpio requirement
dt-bindings: firmware: fsl,scu: Mark multi-channel MU layouts as deprecated
cpufreq: s5pv210: Simplify with scoped for each OF child loop
dmaengine: fsl_raid: Simplify with scoped for each OF child loop
clk: imx: imx31: Simplify with scoped for each OF child loop
clk: imx: imx27: Simplify with scoped for each OF child loop
cdx: Use mutex guard to simplify error handling
cdx: Simplify with scoped for each OF child loop
powerpc/wii: Simplify with scoped for each OF child loop
powerpc/fsp2: Simplify with scoped for each OF child loop
ARM: exynos: Simplify with scoped for each OF child loop
ARM: at91: Simplify with scoped for each OF child loop
of: Add for_each_compatible_node_scoped() helper
dt-bindings: Fix emails with spaces or missing brackets
scripts/dtc: Update to upstream version v1.7.2-62-ga26ef6400bd8
dt-bindings: crypto: inside-secure,safexcel: Mandate only ring IRQs
dt-bindings: crypto: inside-secure,safexcel: Add SoC compatibles
of: reserved_mem: Fix placement of __free() annotation
...
Reference the common PHY properties so RX and TX SerDes lane polarity
of the SGMII/1000Base-X/2500Base-X port can be configured.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/f556ef8be75e37a2f864b9d905a78962bbe76d18.1769916962.git.daniel@makrotopia.org
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- ath drivers: small features/cleanups
- rtw drivers: mostly refactoring for rtw89 RTL8922DE support
- mac80211: use hrtimers for CAC to avoid too long delays
- cfg80211/mac80211: some initial UHR (Wi-Fi 8) support
-----BEGIN PGP SIGNATURE-----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=/NUu
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-02-04' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Some more changes, including pulls from drivers:
- ath drivers: small features/cleanups
- rtw drivers: mostly refactoring for rtw89 RTL8922DE support
- mac80211: use hrtimers for CAC to avoid too long delays
- cfg80211/mac80211: some initial UHR (Wi-Fi 8) support
* tag 'wireless-next-2026-02-04' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (59 commits)
wifi: brcmsmac: phy: Remove unreachable error handling code
wifi: mac80211: Add eMLSR/eMLMR action frame parsing support
wifi: mac80211: add initial UHR support
wifi: cfg80211: add initial UHR support
wifi: ieee80211: add some initial UHR definitions
wifi: mac80211: use wiphy_hrtimer_work for CAC timeout
wifi: mac80211: correct ieee80211-{s1g/eht}.h include guard comments
wifi: ath12k: clear stale link mapping of ahvif->links_map
wifi: ath12k: Add support TX hardware queue stats
wifi: ath12k: Add support RX PDEV stats
wifi: ath12k: Fix index decrement when array_len is zero
wifi: ath12k: support OBSS PD configuration for AP mode
wifi: ath12k: add WMI support for spatial reuse parameter configuration
dt-bindings: net: wireless: ath11k-pci: deprecate 'firmware-name' property
wifi: ath11k: add usecase firmware handling based on device compatible
wifi: ath10k: sdio: add missing lock protection in ath10k_sdio_fw_crashed_dump()
wifi: ath10k: fix lock protection in ath10k_wmi_event_peer_sta_ps_state_chg()
wifi: ath10k: snoc: support powering on the device via pwrseq
wifi: rtw89: pci: warn if SPS OCP happens for RTL8922DE
wifi: rtw89: pci: restore LDO setting after device resume
...
====================
Link: https://patch.msgid.link/20260204121143.181112-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As per the RZ/G3L Hardware manual, CPG_CLKON_ETH register bits{12,13} are
to control the RMII{tx, rx} clocks. Document the rmii{tx.rx} clocks for
RZ/G3L SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260203104541.264759-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The S32 chipsets have a GPR region which has a miscellaneous registers
including the GMAC_0_CTRL_STS register. Originally, this code accessed
that register in a sort of ad-hoc way, but it's cleaner to use a
syscon interface to access these registers.
We still need to maintain the old method of accessing the GMAC register
but using a syscon will let us access other registers more cleanly.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/3b75e950b2f8faecd1a9fa757e7eb7b42ace838f.1769764941.git.dan.carpenter@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Broadcom AMAC controller is DMA coherent on some platforms, so allow
the dma-coherent property.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251215212709.3320889-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Add device tree binding support for the Gigabit Ethernet (GBETH) IP on
Renesas RZ/G3L SoC. This SoC uses different Synopsys DesignWare MAC
version 5.30 compared to RZ/G3E.
RZ/G3L requires an extra clock compared to RZ/G3E and has pps interrupts.
Add a new compatible string "renesas,r9a08g046-gbeth" for RZ/G3L SoC and
update the schema to handle hardware differences between SoC variants.
Extend the base snps,dwmac.yaml schema to accommodate the PPS interrupts.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20260131161250.5047-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A set of small features and cleanups for the next merge window.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaYC1fQAKCRAsFbugiYzL
ewYLAQDbVliEG5O2mVij/CIwUwfkvuYim9xolxec+TzfwShPsAD+NM4qAuHTFKOp
bK0hF4v+Bxy03SE/5QuhPZsC1RsQTgE=
=1LW5
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20260202' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.20/v7.0 (#3)
A set of small features and cleanups for the next merge window.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEn/sM2K9nqF/8FWzzDHRl3/mQkZwFAml91NkTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAMdGXf+ZCRnJkSB/wOdPfielzOfa4tmEQZGXW/tHXRBTbM
l7o0WjZtpWdTlqGYyHNngwPC8ie8SwP+vo6H6D9hPmLyxoQhIg8Kgi0GXh2t6n3s
UgpC+aTTtkbOtIaJL5r4xamuoyxw0KN0Y0FJSX+JnV03qe4BsQvTNAPbTdST29Bu
OC7GquBY37B2qe04B51AgeSEuKlVV1jfUmwa0N2Ugdb/LEiKe8W8PmGIiv3RnHQI
Ec2R+Tw+VZ6yX/qIMKJVeykejAxPw9GVbtfH0sBb1ZgWKPGxAYdMmlulqTzpBl2A
8KDNmmWX23giO6k1iTnDVsfNFtGXZBMuH3EIJMkM+hBWk9ZN2h24ROY3
=q55P
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.20-20260131' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2026-01-31
This first 2 patches are by Biju Das, target the rcar_canfd driver and
add support for FD-only mode.
Lad Prabhakar's patches, also for the rcar_canfd driver add support
for the RZ/T2H SoC.
The last 2 patches are by Michael Tretter and me, target the sja1000
driver and clean up the CAN state handling.
* tag 'linux-can-next-for-6.20-20260131' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: sja1000: sja1000_err(): use error counter for error state
can: sja1000: sja1000_err(): make use of sja1000_get_berr_counter() to read error counters
can: rcar_canfd: Add RZ/T2H support
dt-bindings: can: renesas,rcar-canfd: Document RZ/T2H and RZ/N2H SoCs
dt-bindings: can: renesas,rcar-canfd: Document RZ/V2H(P) and RZ/V2N SoCs
dt-bindings: can: renesas,rcar-canfd: Specify reset-names
can: rcar_canfd: Add support for FD-Only mode
dt-bindings: can: renesas,rcar-canfd: Document renesas,fd-only property
====================
Link: https://patch.msgid.link/20260131101512.1958907-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The firmware-name property was originally introduced to allow end-users
and integrators to select use-case-specific firmware for the WCN6855.
However, specifying firmware for an M.2 WLAN module in the Device Tree
is not appropriate. Instead, this functionality will be handled within
the ath11k driver. Therefore, the firmware-name property is now
deprecated.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260121095055.3683957-3-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
- cfg80211/mac80211
- most of EPPKE/802.1X over auth frames support
- additional FTM capabilities
- split up drop reasons better, removing generic RX_DROP
- NAN cleanups/fixes
- ath11k:
- support for Channel Frequency Response measurement
- ath12k:
- support for the QCC2072 chipset
- iwlwifi:
- partial NAN support
- UNII-9 support
- some UHR/802.11bn FW APIs
- remove most of MLO/EHT from iwlmvm
(such devices use iwlmld)
- rtw89:
- preparations for RTL8922DE support
-----BEGIN PGP SIGNATURE-----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=70Rs
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-01-29' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Another fairly large set of changes, notably:
- cfg80211/mac80211
- most of EPPKE/802.1X over auth frames support
- additional FTM capabilities
- split up drop reasons better, removing generic RX_DROP
- NAN cleanups/fixes
- ath11k:
- support for Channel Frequency Response measurement
- ath12k:
- support for the QCC2072 chipset
- iwlwifi:
- partial NAN support
- UNII-9 support
- some UHR/802.11bn FW APIs
- remove most of MLO/EHT from iwlmvm
(such devices use iwlmld)
- rtw89:
- preparations for RTL8922DE support
* tag 'wireless-next-2026-01-29' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (184 commits)
wifi: iwlegacy: add missing mutex protection in il4965_store_tx_power()
wifi: iwlegacy: add missing mutex protection in il3945_store_measurement()
wifi: mac80211: use u64_stats_t with u64_stats_sync properly
wifi: p54: Fix memory leak in p54_beacon_update()
wifi: cfg80211: treat deprecated INDOOR_SP_AP_OLD control value as LPI mode
wifi: rtw88: sdio: Migrate to use sdio specific shutdown function
wifi: rsi: sdio: Migrate to use sdio specific shutdown function
sdio: Provide a bustype shutdown function
wifi: nl80211/cfg80211: support operating as RSTA in PMSR FTM request
wifi: nl80211/cfg80211: add negotiated burst period to FTM result
wifi: nl80211/cfg80211: clarify periodic FTM parameters for non-EDCA based ranging
wifi: nl80211/cfg80211: add new FTM capabilities
wifi: iwlwifi: rename struct iwl_mcc_allowed_ap_type_cmd::offset_map
wifi: iwlwifi: mvm: Remove link_id from time_events
wifi: iwlwifi: mld: change cluster_id type to u8 array
wifi: iwlwifi: support V13 of iwl_lari_config_change_cmd
wifi: iwlwifi: split bios_value_u32 to separate the header
wifi: iwlwifi: uefi: cache the DSM functions
wifi: iwlwifi: acpi: cache the DSM functions
wifi: iwlwifi: mvm: Cleanup MLO code
...
====================
Link: https://patch.msgid.link/20260129110136.176980-39-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit bd3f305886 ("dt-bindings: bluetooth: qualcomm: describe the
inputs from PMU for wcn7850") changed the binding to new description
with a Power Management Unit (PMU), thus certain power-controller
properties are considered deprecated and are part of that PMUs binding.
Deprecate them to mark clearly that new PMU-based approach is preferred.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
One big Qualcomm Bluetooth schema is hardly manageable: it lists all
possible properties (19 supplies). Split qcom,wcn7850-bt to separate
bindings, so device schema will be easier to read/maintain and list only
relevant properties. Re-shuffle few properties to alphabetical order
while moving them and drop redundant enable-gpios description.
This makes the source qualcomm-bluetooth.yaml binding empty, thus drop
it making entire change a variant of file rename.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 5f4f954bba ("dt-bindings: bluetooth: bring the HW description
closer to reality for wcn6855") changed the binding to new description
with a Power Management Unit (PMU), thus certain power-controller
properties are considered deprecated and are part of that PMUs binding.
Deprecate them to mark clearly that new PMU-based approach is preferred.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
One big Qualcomm Bluetooth schema is hardly manageable: it lists all
possible properties (19 supplies). Split qcom,wcn6855-bt to separate
bindings, so device schema will be easier to read/maintain and list only
relevant properties.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit cca4fe3497 ("dt-bindings: bluetooth: Utilize PMU abstraction
for WCN6750") changed the binding to new description with a Power
Management Unit (PMU), thus certain power-controller properties are
considered deprecated and are part of that PMUs binding.
Deprecate them to mark clearly that new PMU-based approach is preferred.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
One big Qualcomm Bluetooth schema is hardly manageable: it lists all
possible properties (19 supplies). Split qcom,wcn6750-bt to separate
bindings, so device schema will be easier to read/maintain and list only
relevant properties.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
