linux/Documentation/devicetree/bindings/pinctrl/renesas,r9a09g077-pinctrl.yaml

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/renesas,r9a09g077-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Renesas RZ/T2H and RZ/N2H Pin and GPIO controller

maintainers:
  - Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

description:
  The Renesas RZ/T2H and RZ/N2H SoCs feature a combined Pin and GPIO controller.
  Pin multiplexing and GPIO configuration are performed on a per-pin basis.
  Each port supports up to 8 pins, each configurable for either GPIO (port mode)
  or alternate function mode. Each pin supports function mode values ranging from
  0x0 to 0x2A, allowing selection from up to 43 different functions.

properties:
  compatible:
    enum:
      - renesas,r9a09g077-pinctrl # RZ/T2H
      - renesas,r9a09g087-pinctrl # RZ/N2H

  reg:
    minItems: 1
    items:
      - description: Non-safety I/O Port base
      - description: Safety I/O Port safety region base
      - description: Safety I/O Port Non-safety region base

  reg-names:
    minItems: 1
    items:
      - const: nsr
      - const: srs
      - const: srn

  gpio-controller: true

  '#gpio-cells':
    const: 2
    description:
      The first cell contains the global GPIO port index, constructed using the
      RZT2H_GPIO() helper macro from <dt-bindings/pinctrl/renesas,r9a09g077-pinctrl.h>
      (e.g. "RZT2H_GPIO(3, 0)" for P03_0). The second cell represents the consumer
      flag. Use the macros defined in include/dt-bindings/gpio/gpio.h.

  gpio-ranges:
    maxItems: 1

  interrupt-controller: true

  '#interrupt-cells':
    const: 2
    description:
      The first cell contains the global GPIO port index, constructed using the
      RZT2H_GPIO() helper macro from <dt-bindings/pinctrl/renesas,r9a09g077-pinctrl.h>
      and the second cell is used to specify the flag.
      E.g. "interrupts = <RZT2H_GPIO(8, 6) IRQ_TYPE_EDGE_FALLING>;" if P08_6 is
      being used as an interrupt.

  clocks:
    maxItems: 1

  power-domains:
    maxItems: 1

definitions:
  renesas-rzt2h-n2h-pins-node:
    type: object
    allOf:
      - $ref: pincfg-node.yaml#
      - $ref: pinmux-node.yaml#
    properties:
      pinmux:
        description:
          Values are constructed from I/O port number, pin number, and
          alternate function configuration number using the RZT2H_PORT_PINMUX()
          helper macro from <dt-bindings/pinctrl/renesas,r9a09g077-pinctrl.h>.
      pins: true
      phandle: true
      input: true
      input-enable: true
      output-enable: true
      bias-disable: true
      bias-pull-down: true
      bias-pull-up: true
      input-schmitt-enable: true
      input-schmitt-disable: true
      slew-rate:
        description: 0 is slow slew rate, 1 is fast slew rate
        enum: [0, 1]
      drive-strength-microamp:
        description: |
          Four discrete levels are supported (via registers DRCTLm), corresponding
          to the following nominal values:
          - 2500  (Low strength)
          - 5000  (Middle strength)
          - 9000  (High strength)
          - 11800 (Ultra High strength)          
        enum: [2500, 5000, 9000, 11800]
    oneOf:
      - required: [pinmux]
      - required: [pins]
    additionalProperties: false

patternProperties:
  # Grouping nodes: allow multiple "-pins" subnodes within a "-group"
  '.*-group$':
    type: object
    description:
      Pin controller client devices can organize pin configuration entries into
      grouping nodes ending in "-group". These group nodes may contain multiple
      child nodes each ending in "-pins" to configure distinct sets of pins.
    additionalProperties: false
    patternProperties:
      '-pins$':
        $ref: '#/definitions/renesas-rzt2h-n2h-pins-node'

  # Standalone "-pins" nodes under client devices or groups
  '-pins$':
    $ref: '#/definitions/renesas-rzt2h-n2h-pins-node'

  '-hog$':
    type: object
    description: GPIO hog node
    properties:
      gpio-hog: true
      gpios: true
      input: true
      output-high: true
      output-low: true
      line-name: true
    required:
      - gpio-hog
      - gpios
    additionalProperties: false

allOf:
  - $ref: pinctrl.yaml#

required:
  - compatible
  - reg
  - reg-names
  - gpio-controller
  - '#gpio-cells'
  - gpio-ranges
  - clocks
  - power-domains

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/clock/renesas,r9a09g077-cpg-mssr.h>
    #include <dt-bindings/pinctrl/renesas,r9a09g077-pinctrl.h>

    pinctrl@802c0000 {
        compatible = "renesas,r9a09g077-pinctrl";
        reg = <0x802c0000 0x2000>,
              <0x812c0000 0x2000>,
              <0x802b0000 0x2000>;
        reg-names = "nsr", "srs", "srn";
        clocks = <&cpg CPG_CORE R9A09G077_CLK_PCLKM>;
        gpio-controller;
        #gpio-cells = <2>;
        gpio-ranges = <&pinctrl 0 0 288>;
        interrupt-controller;
        #interrupt-cells = <2>;
        power-domains = <&cpg>;

        serial0-pins {
            pinmux = <RZT2H_PORT_PINMUX(38, 0, 1)>, /* Tx */
                     <RZT2H_PORT_PINMUX(38, 1, 1)>; /* Rx */
        };

        sd1-pwr-en-hog {
            gpio-hog;
            gpios = <RZT2H_GPIO(39, 2) 0>;
            output-high;
            line-name = "sd1_pwr_en";
        };

        i2c0-pins {
            pins = "RIIC0_SDA", "RIIC0_SCL";
            input-enable;
        };

        sd0-sd-group {
            ctrl-pins {
                pinmux = <RZT2H_PORT_PINMUX(12, 0, 0x29)>, /* SD0_CLK */
                         <RZT2H_PORT_PINMUX(12, 1, 0x29)>; /* SD0_CMD */
            };

            data-pins {
                pinmux = <RZT2H_PORT_PINMUX(12, 0, 0x29)>, /* SD0_CLK */
                         <RZT2H_PORT_PINMUX(12, 1, 0x29)>; /* SD0_CMD */
            };
        };
    };