mirror of
https://github.com/torvalds/linux.git
synced 2026-09-14 16:10:02 +02:00
26ae421f7f
-----BEGIN PGP SIGNATURE-----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=h+xD
-----END PGP SIGNATURE-----
Merge tag 'pci-v7.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Remove MPS/MRRS Kconfig settings (CONFIG_PCIE_BUS_*) that worked
around a WiFi device defect; use a quirk or boot-time
"pci=pcie_bus_tune_*" kernel parameter instead (Bjorn Helgaas)
- Always lift 2.5GT/s restriction in PCIe failed link retraining to
avoid clamping a link to 2.5GT/s after hot-plug changes the device
(Maciej W. Rozycki)
- Request bus reassignment when not probe-only to fix an enumeration
regression on Marvell CN106XX and possibly other DT-based systems
(Ratheesh Kannoth)
- Fix procfs race between pci_proc_init() and pci_bus_add_device()
that resulted in 'proc_dir_entry ... already registered' warnings
and pointer corruption (Krzysztof Wilczyński)
- Fix sysfs race that causes 'duplicate filename' warnings and boot
panics by converting PCI resource files to static attributes
(Krzysztof Wilczyński)
- Expose sysfs 'resourceN_resize' attributes only on platforms with
PCI mmap (Krzysztof Wilczyński)
- Require CAP_SYS_ADMIN to write to sysfs 'resourceN_resize'
attributes (Krzysztof Wilczyński)
- Add security_locked_down(LOCKDOWN_PCI_ACCESS) to alpha PCI resource
mmap path to match the generic path (Krzysztof Wilczyński)
- Use kstrtobool() to parse the 'rom' attribute input to avoid the
unexpected behavior of enabling the ROM when writing '0' with no
trailing newline (Krzysztof Wilczyński)
Resource management:
- Improve resource claim logging for debuggability (Ilpo Järvinen)
- Clean up several uses of const parameters (Ilpo Järvinen)
- Check option ROM header signatures and lengths before accessing to
avoid page faults and alignment faults (Guixin Liu)
ASPM:
- Don't reconfigure ASPM when entering low-power D-state; only do it
when returning back to D0 (Carlos Bilbao)
Power management:
- During suspend, set power state to 'unknown' for all devices, not
just those with drivers (Lukas Wunner)
- Skip restoring Resizable BARs and VF Resizable BARs if device
doesn't respond to config reads, to avoid invalid array accesses
(Marco Nenciarini)
- Add pci_suspend_retains_context() so drivers can tell whether
devices retain internal state across suspend/resume, since some
platforms reset devices on suspend; use this in nvme to avoid
issues on Qcom RCs (Manivannan Sadhasivam)
Power control:
- Only to power on/off devices that actually support power control to
avoid poking at incompatible devices mentioned in DT (Manivannan
Sadhasivam)
Virtualization and resets:
- Log device readiness timeouts as errors, not warnings, because the
device is likely unusable in this case (Bjorn Helgaas)
- Wait for device readiness after soft reset (D3hot ->
D0uninitialized transition), when the device may respond with
Request Retry Status (RRS) if it needs more time to initialize
(Bjorn Helgaas)
- Drop unnecessary retries when restoring BARs because resets should
now already include all required delays (Lukas Wunner)
- Avoid FLR for MediaTek MT7925 WiFi, where FLR fails after a VM
terminates uncleanly (Jose Ignacio Tornos Martinez)
- Avoid SBR for Qualcomm WCN6855/WCN7850 WiFi, SDX62/SDX65 modems,
which seem not to support it correctly (Jose Ignacio Tornos
Martinez)
Peer-to-peer DMA:
- Prevent P2PDMA as well as CPU access to non-mappable BARs, e.g.,
s390 ISM BARs (Matt Evans)
- Add Intel QAT, DSA, IAA devices to whitelist (Lukas Wunner)
Endpoint framework:
- Add endpoint controller APIs for use by function drivers to
discover auxiliary blocks like DMA engines (Koichiro Den)
- Remember DesignWare eDMA engine base/size and expose them via the
EPC aux-resource API (Koichiro Den)
- Add endpoint embedded doorbell fallback, used if MSI allocation
fails (Koichiro Den)
- Validate BAR index and remove dead BAR read in endpoint doorbell
test (Carlos Bilbao)
- Unwind MSI/MSI-X vectors if NTB initialization fails part-way
through (Koichiro Den)
- Cache sleepable pci_irq_vector() value at ISR setup to avoid
calling it from hardirq context (Koichiro Den)
- Call sleepable pci_epc_raise_irq() from a work item instead of
atomic context, e.g., when setting bits in NTB peer doorbells in
the ntb_peer_db_set() path (Koichiro Den)
- Report 0-based vNTB doorbell vector to account for link event 0 and
historically skipped slot 1 (Koichiro Den)
- Prevent configfs writes to vNTB db_count and other values that are
already in use after EPC attach (Koichiro Den)
- Account for vNTB db_valid reserved slots (link event 0 and
historically skipped slot 1) so they don't appear as valid
doorbells (Koichiro Den)
- Implement vNTB .db_vector_count()/mask() for doorbells so clients
can use multiple vectors and avoid thundering herds (Koichiro Den)
- Report 0-based NTB doorbell vector to account for link event 0 and
historically skipped slot 1 (Koichiro Den)
- Fix doorbell bitmask and IRQ vector handling to clear only
specified bits, use the correct vector for non-contiguous Linux IRQ
numbers, and validate incoming vectors (Koichiro Den)
- Implement NTB .db_vector_count()/mask() for doorbells so clients
can use multiple vectors (Koichiro Den)
Native PCIe controller infrastructure:
- Add pci_host_common_link_train_delay() for the mandatory delay
after > 5GT/s Link training completes and use it for cadence HPA,
j721e, LGA; dwc; aardvark, mediatek-gen3, rzg3s (Hans Zhang)
- Protect root bus removal with rescan lock in altera, brcmstb,
cadence, dwc, iproc, mediatek, plda, rockchip to prevent
use-after-free or crashes when racing with sysfs rescan or hotplug
(Hans Zhang)
- Add pci_host_common_parse_ports() for use by any native driver to
parse Root Port properties (per-Link features like width, speed,
PHY, power and reset control, etc should be described in Root Port
stanzas, not the host bridge; currently only reset GPIOs
implemented) (Sherry Sun)
New native PCIe controller drivers:
- Add DT binding and driver for UltraRISC DP1000 PCIe controller
(Xincheng Zhang, Jia Wang)
Altera PCIe controller driver:
- Do not dispose of the parent IRQ mapping, which belongs to the
parent interrupt controller (Mahesh Vaidya)
- Fix chained IRQ handler ordering issue and resource leaks on probe
failure (Mahesh Vaidya)
AMD MDB PCIe controller driver:
- Assert PERST# on shutdown so any connected Endpoints are held in
reset during shutdown (Sai Krishna Musham)
Amlogic Meson PCIe controller driver:
- Propagate devm_add_action_or_reset() failure to fix probe error
path (Shuvam Pandey)
- Add .remove() callback to deinitialize the host bridge and power
off the PHY (Shuvam Pandey)
Broadcom iProc PCIe controller driver:
- Restore .map_irq() assignment; its removal broke INTx on the iproc
platform bus driver (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- No change, but products using certain WiFi devices may be affected
by removal of CONFIG_PCIE_BUS_* (see above)
Freescale i.MX6 PCIe controller driver:
- Move IMX6SX_GPR12_PCIE_TEST_POWERDOWN handling into the core reset
functions (Richard Zhu)
- Assert PERST# before enabling regulators to ensure that even if
power is enabled, endpoint stays inactive until REFCLK is stable
(Sherry Sun)
- Parse reset properties in Root Port nodes (falling back to host
bridge) to help support Key E connectors and the pwrctrl framework
(Sherry Sun)
- Configure i.MX95 REF_USE_PAD before PHY reset (Richard Zhu)
- Assert i.MX95 ref_clk_en after reference clock stabilizes (Richard
Zhu)
- Integrate new pwrctrl API for DTs with Root Port-level power
supplies (Sherry Sun)
Intel Gateway PCIe controller driver:
- Enable clock before PHY init for correct ordering (Florian Eckert)
- Add .start_link() callback so the driver works again (Florian
Eckert)
- Stop overwriting the ATU base address discovered by
dw_pcie_get_resources() (Florian Eckert)
- Add DT 'atu' region since this is hardware-specific, and fall back
to driver default if lacking (Florian Eckert)
Loongson PCIe controller driver:
- Ignore downstream devices only on internal bridges to avoid
Loongson hardware issue (Rong Zhang)
- Quirk old Loongson-3C6000 bridges that advertise incorrect
supported link speeds (Ziyao Li)
Marvell MVEBU PCIe controller driver:
- Use fixed-width interrupt masks to avoid truncation in 64-bit
builds (Rosen Penev)
MediaTek PCIe controller driver:
- Use FIELD_PREP() to fix incorrect operator precedence in
PCIE_FTS_NUM_L0 (Li RongQing)
- Fix IRQ domain leak when port fails to enable (Manivannan
Sadhasivam)
- Use actual physical address for MSI message address instead of
virt_to_phys() (Manivannan Sadhasivam)
- Add EcoNet EN7528 to DT binding (Caleb James DeLisle)
MediaTek PCIe Gen3 controller driver:
- Deassert PCIE_PHY_RSTB so REFCLK is stable for at least 100ms
(PCIE_T_PVPERL_MS) before deasserting PERST# (Jian Yang)
- Add .shutdown() to assert PERST# before powering down device (Jian
Yang)
- Do full device power down on removal, including asserting PERST#,
when removing driver (Chen-Yu Tsai)
- Fix a 'failed to create pwrctrl devices' error message that was
inadvertently skipped (Chen-Yu Tsai)
NVIDIA Tegra194 PCIe controller driver:
- Program the DesignWare PORT_AFR L1 entrance latency based on the
'aspm-l1-entry-delay-ns' DT property (Manikanta Maddireddy)
Qualcomm PCIe controller driver:
- Add Eliza SoC compatible in DT binding (Krishna Chaitanya Chundru)
- Set max OPP during resume so DBI register accesses don't fail with
NoC errors (Qiang Yu)
- Add pci_host_common_d3cold_possible() to determine whether
downstream devices are already in D3hot and wakeup-enabled devices
are capable of generating PME from D3cold (Krishna Chaitanya
Chundru)
- Add .get_ltssm() callback to get the LTSSM status without DBI,
since DBI may be inaccessible after PME_Turn_Off (Krishna Chaitanya
Chundru)
- Power down PHY via PARF_PHY_CTRL before disabling rails/clocks to
avoid power leakage (Krishna Chaitanya Chundru)
- Decide whether suspend should put the link in L2 and power down
using pci_host_common_d3cold_possible() instead of checking whether
ASPM L1 is enabled (Krishna Chaitanya Chundru)
- Add qcom D3cold support to tear down interconnect bandwidth and OPP
votes (Krishna Chaitanya Chundru)
- Handle unsupported mixed PERST#/PHY DT configurations, e.g., PHY in
RP node while PERST# is in the RC node, but warn about the DT issue
(Qiang Yu)
- Program T_POWER_ON based on DT 't-power-on-us' property in case
hardware advertises incorrect values (Krishna Chaitanya Chundru)
- Disable ASPM L0s for SA8775P (Shawn Guo)
- Initialize DWC MSI lock for firmware-managed ECAM hosts, which
don't use the dw_pcie_host_init() path that initializes the lock
(Yadu M G)
Renesas RZ/G3S PCIe controller driver:
- Add RZ/V2N DT support (Lad Prabhakar)
SOPHGO PCIe controller driver:
- Add 'dma-coherent' DT property for sg2042-pcie driver (Han Gao)
Synopsys DesignWare PCIe controller driver:
- Apply ECRC TLP Digest workaround for all DesignWare cores prior to
5.10a, not just 4.90a and 5.00a (Manikanta Maddireddy)
- Use common struct dw_pcie 'mode' rather than duplicating it in
artpec6, dra7xx, dwc-pcie, and keembay driver structs (Hans Zhang)
- Use DEFINE_SHOW_ATTRIBUTE for ltssm_status debugfs to reduce
boilerplate and fix a seq_file memory leak by including a
.release() callback (Hans Zhang)
- Fix a signedness bug in fault injection test code (Dan Carpenter)
- Avoid NULL pointer dereference when tearing down debugfs for
controller that lacks RAS DES capability (Shuvam Pandey)
MicroSemi Switchtec management driver:
- Add Gen6 Device IDs (Ben Reed)
Miscellaneous:
- Remove unused gpio.h include from amd-mdb, designware-plat, fu740,
visconti drivers (Andy Shevchenko)
- Fix typos in documentation (josh ziegler)
- Use FIELD_MODIFY() instead of open-coding it (Hans Zhang)"
* tag 'pci-v7.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (168 commits)
PCI/sysfs: Use kstrtobool() to parse the ROM attribute input
PCI/sysfs: Limit BAR resize attribute scope to platforms with PCI mmap
PCI/sysfs: Remove pci_create_legacy_files() and pci_sysfs_init()
PCI/sysfs: Convert legacy I/O and memory attributes to static definitions
PCI/sysfs: Add __weak pci_legacy_has_sparse() helper
alpha/PCI: Compute legacy size in pci_mmap_legacy_page_range()
PCI: Add macros for legacy I/O and memory address space sizes
PCI/sysfs: Remove pci_{create,remove}_sysfs_dev_files()
alpha/PCI: Convert resource files to static attributes
alpha/PCI: Add static PCI resource attribute macros
alpha/PCI: Remove WARN from __pci_mmap_fits() and __legacy_mmap_fits()
alpha/PCI: Fix __pci_mmap_fits() overflow for zero-length BARs
alpha/PCI: Use PCI resource accessor macros
alpha/PCI: Use BAR index in sysfs attr->private instead of resource pointer
alpha/PCI: Add security_locked_down() check to pci_mmap_resource()
PCI/sysfs: Limit pci_sysfs_init() late_initcall compile scope
PCI/sysfs: Add stubs for pci_{create,remove}_sysfs_dev_files()
PCI/sysfs: Warn about BAR resize failure in __resource_resize_store()
PCI/sysfs: Convert PCI resource files to static attributes
PCI/proc: Fix race between pci_proc_init() and pci_bus_add_device()
...
|
||
|---|---|---|
| .. | ||
| ptrace | ||
| syscalls | ||
| trace | ||
| vdso | ||
| .gitignore | ||
| 85xx_entry_mapping.S | ||
| align.c | ||
| asm-offsets.c | ||
| audit_32.h | ||
| btext.c | ||
| cacheinfo.c | ||
| cacheinfo.h | ||
| cpu_setup_6xx.S | ||
| cpu_setup_44x.S | ||
| cpu_setup_e500.S | ||
| cpu_setup_pa6t.S | ||
| cpu_setup_power.c | ||
| cpu_setup_ppc970.S | ||
| cpu_specs_8xx.h | ||
| cpu_specs_44x.h | ||
| cpu_specs_47x.h | ||
| cpu_specs_85xx.h | ||
| cpu_specs_book3s_32.h | ||
| cpu_specs_book3s_64.h | ||
| cpu_specs_e500mc.h | ||
| cpu_specs.h | ||
| cputable.c | ||
| crash_dump.c | ||
| dawr.c | ||
| dbell.c | ||
| dexcr.c | ||
| dma-iommu.c | ||
| dma-mask.c | ||
| dma-swiotlb.c | ||
| dt_cpu_ftrs.c | ||
| early_32.c | ||
| eeh_cache.c | ||
| eeh_driver.c | ||
| eeh_event.c | ||
| eeh_pe.c | ||
| eeh_sysfs.c | ||
| eeh.c | ||
| entry_32.S | ||
| epapr_hcalls.S | ||
| epapr_paravirt.c | ||
| exceptions-64e.S | ||
| exceptions-64s.S | ||
| fadump.c | ||
| firmware.c | ||
| fpu.S | ||
| head_8xx.S | ||
| head_32.h | ||
| head_44x.S | ||
| head_64.S | ||
| head_85xx.S | ||
| head_book3s_32.S | ||
| head_booke.h | ||
| hw_breakpoint_constraints.c | ||
| hw_breakpoint.c | ||
| idle_6xx.S | ||
| idle_64e.S | ||
| idle_85xx.S | ||
| idle_book3s.S | ||
| idle.c | ||
| ima_arch.c | ||
| interrupt_64.S | ||
| interrupt.c | ||
| io.c | ||
| iomap.c | ||
| iommu.c | ||
| irq_64.c | ||
| irq.c | ||
| isa-bridge.c | ||
| jump_label.c | ||
| kdebugfs.c | ||
| kgdb.c | ||
| kprobes-ftrace.c | ||
| kprobes.c | ||
| kvm_emul.S | ||
| kvm.c | ||
| l2cr_6xx.S | ||
| legacy_serial.c | ||
| Makefile | ||
| mce_power.c | ||
| mce.c | ||
| misc_32.S | ||
| misc_64.S | ||
| misc.S | ||
| module_32.c | ||
| module_64.c | ||
| module.c | ||
| msi.c | ||
| note.S | ||
| nvram_64.c | ||
| optprobes_head.S | ||
| optprobes.c | ||
| paca.c | ||
| pci_32.c | ||
| pci_64.c | ||
| pci_dn.c | ||
| pci_of_scan.c | ||
| pci-common.c | ||
| pci-hotplug.c | ||
| pmc.c | ||
| ppc_save_regs.S | ||
| proc_powerpc.c | ||
| process.c | ||
| prom_entry_64.S | ||
| prom_init_check.sh | ||
| prom_init.c | ||
| prom_parse.c | ||
| prom.c | ||
| reloc_32.S | ||
| reloc_64.S | ||
| rethook.c | ||
| rtas_entry.S | ||
| rtas_flash.c | ||
| rtas_pci.c | ||
| rtas-proc.c | ||
| rtas-rtc.c | ||
| rtas.c | ||
| rtasd.c | ||
| secure_boot.c | ||
| security.c | ||
| secvar-ops.c | ||
| secvar-sysfs.c | ||
| setup_32.c | ||
| setup_64.c | ||
| setup-common.c | ||
| setup.h | ||
| signal_32.c | ||
| signal_64.c | ||
| signal.c | ||
| signal.h | ||
| smp-tbsync.c | ||
| smp.c | ||
| stacktrace.c | ||
| static_call.c | ||
| suspend.c | ||
| switch.S | ||
| swsusp_32.S | ||
| swsusp_64.c | ||
| swsusp_85xx.S | ||
| swsusp_asm64.S | ||
| swsusp.c | ||
| sys_ppc32.c | ||
| syscall.c | ||
| syscalls.c | ||
| sysfs.c | ||
| systbl.c | ||
| tau_6xx.c | ||
| time.c | ||
| tm.S | ||
| traps.c | ||
| ucall.S | ||
| udbg_16550.c | ||
| udbg.c | ||
| uprobes.c | ||
| vdso.c | ||
| vdso32_wrapper.S | ||
| vdso64_wrapper.S | ||
| vecemu.c | ||
| vector.S | ||
| vmlinux.lds.S | ||
| watchdog.c | ||