mirror of
https://github.com/torvalds/linux.git
synced 2026-08-01 03:59:40 +02:00
Linux kernel source tree
a14e6b69f3
Assuming the test setup described here:
https://patchwork.kernel.org/project/netdevbpf/cover/20210205130240.4072854-1-vladimir.oltean@nxp.com/
(swp1 and swp2 are in bond0, and bond0 is in a bridge with swp0)
it can be seen that when swp1 goes down (on either board A or B), then
traffic that should go through that port isn't forwarded anywhere.
A dump of the PGID table shows the following:
PGID_DST[0] = ports 0
PGID_DST[1] = ports 1
PGID_DST[2] = ports 2
PGID_DST[3] = ports 3
PGID_DST[4] = ports 4
PGID_DST[5] = ports 5
PGID_DST[6] = no ports
PGID_AGGR[0] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[1] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[2] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[3] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[4] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[5] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[6] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[7] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[8] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[9] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[10] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[11] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[12] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[13] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[14] = ports 0, 1, 2, 3, 4, 5
PGID_AGGR[15] = ports 0, 1, 2, 3, 4, 5
PGID_SRC[0] = ports 1, 2
PGID_SRC[1] = ports 0
PGID_SRC[2] = ports 0
PGID_SRC[3] = no ports
PGID_SRC[4] = no ports
PGID_SRC[5] = no ports
PGID_SRC[6] = ports 0, 1, 2, 3, 4, 5
Whereas a "good" PGID configuration for that setup should have looked
like this:
PGID_DST[0] = ports 0
PGID_DST[1] = ports 1, 2
PGID_DST[2] = ports 1, 2
PGID_DST[3] = ports 3
PGID_DST[4] = ports 4
PGID_DST[5] = ports 5
PGID_DST[6] = no ports
PGID_AGGR[0] = ports 0, 2, 3, 4, 5
PGID_AGGR[1] = ports 0, 2, 3, 4, 5
PGID_AGGR[2] = ports 0, 2, 3, 4, 5
PGID_AGGR[3] = ports 0, 2, 3, 4, 5
PGID_AGGR[4] = ports 0, 2, 3, 4, 5
PGID_AGGR[5] = ports 0, 2, 3, 4, 5
PGID_AGGR[6] = ports 0, 2, 3, 4, 5
PGID_AGGR[7] = ports 0, 2, 3, 4, 5
PGID_AGGR[8] = ports 0, 2, 3, 4, 5
PGID_AGGR[9] = ports 0, 2, 3, 4, 5
PGID_AGGR[10] = ports 0, 2, 3, 4, 5
PGID_AGGR[11] = ports 0, 2, 3, 4, 5
PGID_AGGR[12] = ports 0, 2, 3, 4, 5
PGID_AGGR[13] = ports 0, 2, 3, 4, 5
PGID_AGGR[14] = ports 0, 2, 3, 4, 5
PGID_AGGR[15] = ports 0, 2, 3, 4, 5
PGID_SRC[0] = ports 1, 2
PGID_SRC[1] = ports 0
PGID_SRC[2] = ports 0
PGID_SRC[3] = no ports
PGID_SRC[4] = no ports
PGID_SRC[5] = no ports
PGID_SRC[6] = ports 0, 1, 2, 3, 4, 5
In other words, in the "bad" configuration, the attempt is to remove the
inactive swp1 from the destination ports via PGID_DST. But when a MAC
table entry is learned, it is learned towards PGID_DST 1, because that
is the logical port id of the LAG itself (it is equal to the lowest
numbered member port). So when swp1 becomes inactive, if we set
PGID_DST[1] to contain just swp1 and not swp2, the packet will not have
any chance to reach the destination via swp2.
The "correct" way to remove swp1 as a destination is via PGID_AGGR
(remove swp1 from the aggregation port groups for all aggregation
codes). This means that PGID_DST[1] and PGID_DST[2] must still contain
both swp1 and swp2. This makes the MAC table still treat packets
destined towards the single-port LAG as "multicast", and the inactive
ports are removed via the aggregation code tables.
The change presented here is a design one: the ocelot_get_bond_mask()
function used to take an "only_active_ports" argument. We don't need
that. The only call site that specifies only_active_ports=true,
ocelot_set_aggr_pgids(), must retrieve the entire bonding mask, because
it must program that into PGID_DST. Additionally, it must also clear the
inactive ports from the bond mask here, which it can't do if bond_mask
just contains the active ports:
ac = ocelot_read_rix(ocelot, ANA_PGID_PGID, i);
ac &= ~bond_mask; <---- here
/* Don't do division by zero if there was no active
* port. Just make all aggregation codes zero.
*/
if (num_active_ports)
ac |= BIT(aggr_idx[i % num_active_ports]);
ocelot_write_rix(ocelot, ac, ANA_PGID_PGID, i);
So it becomes the responsibility of ocelot_set_aggr_pgids() to take
ocelot_port->lag_tx_active into consideration when populating the
aggr_idx array.
Fixes:
|
||
|---|---|---|
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| fs | ||
| include | ||
| init | ||
| ipc | ||
| kernel | ||
| lib | ||
| LICENSES | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .clang-format | ||
| .cocciconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Linux kernel
============
There are several guides for kernel developers and users. These guides can
be rendered in a number of formats, like HTML and PDF. Please read
Documentation/admin-guide/README.rst first.
In order to build the documentation, use ``make htmldocs`` or
``make pdfdocs``. The formatted documentation can also be read online at:
https://www.kernel.org/doc/html/latest/
There are various text files in the Documentation/ subdirectory,
several of them using the Restructured Text markup notation.
Please read the Documentation/process/changes.rst file, as it contains the
requirements for building and running the kernel, and information about
the problems which may result by upgrading your kernel.